How To Locate Septic Tank In House Built In 1963 In Texas? (Solution found)

How to find a septic tank near your house?

  • As you follow the pipes leaving your house, you can use a thin probe which is also known as a soil probe. You can keep probing every two feet in search of the septic tank. Usually, the septic tanks are constructed between 10 to 25 feet from your house. The tank will not be located very close to your property.

How do you find a septic tank in an old house?

Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.

How do I find out where my septic tank is located?

Follow the Main Sewer Line Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside. The sewer pipes will lead to where your septic tank is located.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

What were septic tanks made of in the 1960s?

In the 1960s, precast concrete tanks became more prevalent as the standard of practice improved. Most tanks were still single compartment 750, 1,000 or 1,200-gallon tanks, usually depending on the size of the house.

Can a metal detector find a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How do you find a buried septic tank?

Tips for locating your septic tank

  1. If the septic tank lid is underground, you can use a metal detector to locate it.
  2. You can use a flushable transmitter that is flushed in the toilet and then the transmitter is tracked with a receiver.

How far is septic tank from house?

Requirements vary from one area to another, but the normal minimum distance from the house is 10 feet. If you’ll be using a private well for drinking water, however, note that many state departments of health require a minimum of 50 feet between a new septic tank and a well, according to APEC Water.

How do septic tanks look?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.

How do I find out if my septic tank is registered?

Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.

How do I find my septic lateral lines?

Call your local electric utility provider or gas company to locate buried gas or utility lines before digging. A septic tank probe can also help you find the location. Stick the long, thin metal probe into the ground until you feel it hit the tank and feel the edges of the tank.

What is OWTS?

An Onsite Wastewater Treatment Systems (OWTS) is a privately owned and maintained sewage disposal system. They are commonly referred to as septic systems. All OWTS have two basic components: a two-compartment septic tank and a disposal field.

What were old septic tanks called?

This treatment chamber became known as the septic tank. Note that the septic tank has a baffle at each end to help keep waste in the tank. The original pit remained as the part of the system that returned “clarified” wastewater to the ground. It now became known as a drywell.

When were septic tanks developed?

This leads us to the very first septic tank, designed by French inventor Jean-louis Mouras in 1860, who believed that storing sewage before discharging it would be better than allowing it to seep into the surrounding land straight away.

When did septic tanks become plastic?

By the 1940s, septic systems were common from coast to coast, and by the 1960s, when these systems began failing, significant improvements to the overall design were developed. Today, most modern septic systems feature more advanced materials, including fiberglass, precast concrete, polyurethane, and other plastics.

Basics for Septic Systems

On-site sewage facilities, also known as OSSFs, must be developed on the basis of a site evaluation that takes into consideration the specific requirements of the location. The system of choice for around 20% of new homes being built in Texas is the radon mitigation system. An On-Site Sewage Facility (OSSF), sometimes known as a “septic system,” is a sewage treatment system that is located on a property. As a result of the unexpected surge in new housing construction in suburban and rural regions, more Texas families are reliant on an OSSF for the treatment and disposal of their domestic sewage.

Systems that accomplish their jobs well while also protecting the environment are made possible by new methods to design and oversight of OSSFs.

A number of soil tests are ruling out traditional systems, which separate liquids from solid waste in a holding tank and then distribute them throughout a drainfield using underground pipes or other proprietary items in many regions of the state.

However, because the majority of Texas soils are incapable of adequately absorbing contaminants, different treatment procedures are necessary.

Any work on an OSSF must be done by a licensed installer or, in the case of a single-family property, by the homeowner himself or herself.

Who checks to make sure the requirements are followed?

Local governments in most parts of the state have taken on the obligation of ensuring that OSSFs in their jurisdictions comply with all applicable state regulations and procedures. There are several local governments that serve as “authorized agents” (AA) of the Texas Commission on Environmental Quality, which is in charge of managing the OSSF Program. A “designated representative” (DR) assists the AA in carrying out their tasks, which include examining plans for constructing, changing, extending, or repairing each OSSF; granting permits; and checking the system’s installation, among others.

The OSSF’s authorized agents and representatives also investigate and respond to complaints to verify that the OSSF is in compliance with minimal requirements.

After that, the agent can file a criminal complaint with the local judge of the peace, who will then investigate the matter.

Industrial or hazardous waste cannot be introduced into an OSSF; instead, this waste will be handled in the soil, destroying the OSSF by actually killing the microorganisms that break down the biosolids and causing it to fail.

Keep in mind that septic systems are intended to manage human waste rather than chemicals.


All OSSFs will require maintenance at some point in their lives. Conventional anaerobic systems require the septic tank to be pumped out on a regular basis in order to remove sediments and prevent the system from backing up. It is advised that you pump your septic tank once every three to five years in order to avoid short circuiting the treatment process and causing damage. To acquire a list of registered sludge transporters in your region, go to theSludge Transporter Queryonline. Aerobic systems are more complicated and require more upkeep than anaerobic ones do.

  • A number of regulatory authorities have enacted more strict rules, which may include homeowner training or even prohibiting homeowners from performing upkeep on their properties.
  • In order to guarantee that the system runs appropriately, it is recommended that you contract with a licensed maintenance provider to verify, debug, and test the system as required by 30 TAC 285.91(4).
  • Once every six months if the system employs an electronic monitor, automated radio, or telephone to alert the maintenance provider of system or component failure as well as to monitor the quantity of disinfection remaining in the system, reporting might be lowered to once every six months.
  • If any needed repairs are not completed, the permitting authority will be notified of the failure.
  • The pills are extremely reactive, and within 10 minutes, they will have killed 99 percent of the germs present in the effluent.
  • Please contact us at (800) 447-2827.
See also:  Standard Septic Tank Test For What? (Best solution)

Where can I find more information and assistance?

The Small Business and Local Government Assistance Section of the Texas Commission on Environmental Quality (TCEQ) provides free, confidential assistance to small enterprises and local governments seeking to comply with state environmental requirements.

Call us at (800) 447-2827 or visit our website at for more information.

Identifying the Main Sewer Clean-Out in Your House

Clogged drains in a single plumbing device, such as a tub or sink, are one thing; they are an issue that is typically pretty simple to resolve. When you have a major drain line blockage, on the other hand, it is a whole other story. This is a clog in the massive, main drainline that serves your entire house and transports all wastewater to the municipal sewage system or to a septic drain field. An obstruction in your primary sewer line causes raw sewage to no longer flow as it should, resulting in backups throughout your whole home, which may be extremely dangerous and even fatal.

A situation that is unpleasant and might be extremely costly to solve.

The Main Clean-Out

Clearing a main sewage line blockage is best accomplished through the use of a fitting known as the mainclean-out valve. Every home should have one, but regrettably, some don’t, despite the fact that they should. Using a drain snake or a motorized auger to dislodge the clog in your main drain line and restore proper function to your home’s drainage system is the best option for you or your plumber in this situation. Finding the major clean-out, on the other hand, is not always straightforward.

Here are some pointers on how to locate your main drain.

Outdoor Clean-Outs

It is common for the primary clean-out fitting to be located outdoors in warm areas when residences are built on slab foundations, generally towards the external walls of the home. Look behind shrubs or inside a metal or plastic box that has been sunk into the earth. Large-diameter pipes with threaded plugs at the top are commonly used as the primary clean-out fitting. Depending on where it is located, it may be elevated above ground near an exterior wall or confined within a ground box with a metal cover.

In a Bathroom or Utility Area

Another option for homes built on slab foundations is to position the main drain in a bathroom, often on the floor near the toilet, or in a garage or utility area, typically in close proximity to a floor drain. Depending on the location, the threaded plug may be flush-mounted into the floor or it may be threaded into a short piece of large-diameter pipe that extends up from the ground level. It may be opened with a big pipe wrench in order to provide access for drain-clearing instruments to be placed within it.

In a Basement

The major clean-out is commonly found on the basement floor, usually along the foundation wall, in buildings built in colder areas where it is standard construction practice to construct dwellings over basements. It will be possible to insert a threaded plug into a short section of large-diameter pipe that reaches up from the floor. If you are having difficulty locating the clean-out, make a direct line from the vertical soil stack to the foundation wall, following the shortest path possible—the main clean-out will most likely be located along this line.

There may be a Y-fitting at the bottom of the main drain soil stack, near where it disappears beneath the concrete slab, if this type of fitting is not present.

In larger homes, there may be two or even three clean-out fittings, one for each of the main drain pipes running from separate soil stacks out to the street.

Routine Maintenance

Most plumbers are capable of performing main drain line cleaning, but there are other firms who specialize in this type of job. An yearly examination and cleaning by a sewer professional is recommended, especially if you have a landscape that includes huge trees. Tree roots may quickly infiltrate sewage lines, and maintaining a regular practice of sewer drain line cleaning will help to avoid a devastating obstruction in the pipelines. Homeowners can clear a clogged main drain, but they may need to use specific instruments, such as a motorized drain auger, which can be rented from tool rental companies and big home improvement stores to do so.

How to locate a septic tank

A home’s construction year and whether a copy of the septic permit is accessible determine the procedure for locating a septic tank on a property, which might take many weeks or months. Please choose one of the scenarios listed below and follow the instructions.

For homes built in the last five (5) years or less

Obtain a copy of your septic tank permit from your local Department of Health and Human Services office. Please fill out as much of the information below as possible to help us expedite the search:

  • Number of the tax map
  • Lot number
  • Block number
  • Address in the physical world
  • When the system was installed or when the house was built (if this information is available)
  • Name of the original permit holder (if any information is available)
  • Name of the subdivision (if the property is located within a subdivision)

A copy of a septic tank permit can be obtained from a local DHEC office by any individual or group, regardless of whether or not they own the land in question.

For homes older than five (5) years or if a copy of the septic permit was not able to be located.

It is recommended that you call an experienced septic contractor who will come to the site and assist you with the identification of the current septic system. You may find a list of licensed septic installers by clicking here.


Septic Tank Alerts Septic Tank Alerts

How to locate a septic tank

A home’s construction year and whether a copy of the septic permit is accessible determine the procedure for locating a septic tank on a property, which might take many weeks or months. Please choose one of the scenarios listed below and follow the instructions.

For homes built in the last five (5) years or less

Obtain a copy of your septic tank permit from your local Department of Health and Human Services office. Please fill out as much of the information below as possible to help us expedite the search:

  • Number of the tax map
  • Lot number
  • Block number
  • Address in the physical world
  • When the system was installed or when the house was built (if this information is available)
  • Name of the original permit holder (if any information is available)
  • Name of the subdivision (if the property is located within a subdivision)

A copy of a septic tank permit can be obtained from a local DHEC office by any individual or group, regardless of whether or not they own the land in question.

For homes older than five (5) years or if a copy of the septic permit was not able to be located.

It is recommended that you call an experienced septic contractor who will come to the site and assist you with the identification of the current septic system. You may find a list of licensed septic installers by clicking here.


Septic Tank Alerts Septic Tank Alerts

See also:  How Much To Empty My Septic Tank?

What You Should Know If Your Home Was Built Before 1975

Cast iron pipes are likely to be found in older homes constructed before 1975, and you should inspect them for signs of wear or damage. Your pipes may be buried beneath the earth or in the basement, but an ounce of prevention is worth a pound of cure when it comes to flooding. You don’t want to wind yourself in the same situation as this family, who was forced to leave their house due to sewage backup. After only 25 years, it is usual for cast iron pipes to begin to deteriorate. Residential pipe systems are subject to typical wear and tear.

Waste pipes made of cast iron have a lifespan ranging from 50 to 100 years.

It is usual for cast iron pipes to deteriorate after just 25 years, thus it is important for homeowners to undertake periodic inspections. It is estimated that 76 million American houses contain cast iron pipes that have failed and must be replaced.

Signs of Trouble

If a homeowner notices that their pipes are rusty, decaying, discolored, or cracked, he or she should see a plumber to assess whether the entire piping system needs to be replaced. The presence of sporadic leaks should be reason for concern since they may lead to a more major flood of water or raw sewage overflow in the future, resulting in foul odors and the attraction of pests to your property. Rather than patching and replacing parts of broken pipes, a complete (and expensive) replacement of the pipes may be necessary.

  • Drains that are slow to drain
  • Clogs or backups
  • Sewage gas odors are foul-smelling. Infestation with roaches and other pests Wood flooring that are warped or split
  • Floor tiles with a tinted surface (raised)
  • Floor tiles that are loose or damaged
  • Floor tiles (grout) that have been discolored by water
  • Carpet or rug/mat that has been damaged or discolored by water

Coughing, sneezing, eye discomfort, and weariness are all symptoms of a leak that can cause major health concerns. A faulty plumbing system may also cause a decrease in the value of a home.


There are a lot of reasons why underground waste pipelines fail. One explanation is exterior corrosion, which is produced by elements contained in the soil, as previously stated. Acidity, stray electric currents, and pollutants are all present in high concentrations in soil, and all of these factors contribute to the rusting of cast iron pipes. External rust is not always a reason for concern, however it may be a sign of more significant issues with the pipe system within the building. Sulfuric acid is corrosive to cast iron, as is sulfur dioxide.

It is possible that waste flowing through pipes could induce a buildup of hydrogen sulfide gas, which will oxidize and form sulfuric acid.

Experts recommend that you verify the contents on household drain cleaners since many of them include sulfuric acid, which promotes the corrosion of the pipes.

Corrosion Is More Common Than You Think

Pipe corrosion is common in American cities, regardless of temperature, although salt and moisture-rich conditions, such as those found in Florida, can exacerbate the problem significantly. However, because domestic plumbing is frequently concealed behind walls or in neglected subterranean tunnels or utility rooms, issues might go unreported for years before they are finally discovered. In order to maintain proper house maintenance practices, homeowners should examine exposed tubing on a regular basis for symptoms of degradation.

Protect Your Rights as a Homeowner

When it comes to homeowners insurance policy, coverage for water damage is a thorny issue that requires careful consideration. If you have experienced financial losses or health concerns as a result of water damage caused by faulty pipes, you may be able to file a genuine claim for compensation. If you have experienced financial losses or health concerns as a result of water damage caused by faulty pipes, you may be able to file a claim for compensation. Generally speaking, most insurers will not pay for pipe repair or replacement, but they may pay for damage caused by deterioration under one condition: you must not have been aware of the problem when you purchased the house in the first place.

A knowledgeable attorney can assist you in appealing a claim denial relating to water damage or in obtaining funds for a complete system replacement. Protect your legal rights as a homeowner by requesting a free case evaluation right now.

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

  1. 3.
  2. Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
  3. Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
  4. When you do, that’s when your septic tank comes into play!
  5. Look for the Lid.
  6. You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
  7. Those areas should be excavated in order to disclose the lids.
  8. Get in touch with the pros.
  9. Lifting concrete lids will necessitate the use of specialized equipment.
  10. A fall into an unprotected septic tank has the potential to be lethal.
  11. Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

How Do I Find My Septic Tank

What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00

How Do I Find My Septic Tank

Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.

A tiny proportion of septic tanks have a capacity of 3000L or more.

Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.

If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

See also:  How To Connect 6 Inch Pvc To Plastic Septic Tank? (TOP 5 Tips)

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

  1. They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
  2. Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
  3. A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
  4. Using an electronic service locator, you may locate a septic tank.
  5. In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
  6. Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
  7. Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

  • There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.

Check the rest of the toilets in the home by repeating the procedure.

Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.

a link to the page’s load

4500 N Interstate 35 Gainesville, TX 76240

Status:Active Farm/Ranch is the type of property. Three thousand nine hundred square feet (MLS:14713449) On the Ground: 92 Days Lot Dimensions: 248 Acres Cooke Ranch has been a well-known horse breeding and training center for many years in the county. Main house with adjacent office, 9 mobile houses suited for stafftrainer living, all in a newly renovated complex. Two huge barns built for mares and foals, two dry mare motel barns, and one wet mare motel barn are among the 16 barns with a total of 200 individual stalls.

With a wide screened holding area, the indoor arena is ideal.

A square cutting pen-arena, a round cutting pen, and an open exercising track are all available.

There are six ponds and many wet weather streams on the property.

Mortgage Calculator

Payment of $000 per month Only the loan and interest are included. Taxes and insurance are not included in the price.

Detailed Maps

Located near 4500 North Interstate 35 in Gainesville, Texas, 76240.


3 bedrooms and 2 bathrooms Bathrooms: 4 full bathrooms and 1 half bathroomYear of construction: 1963 Stories:1 Style:Ranch Block and wood are the primary building materials. Details of the foundation: PierBeam

Features / Amenities

Interior Amenities: Cable television is available. Flooring options include carpet and laminate. Electric cooktop and electric oven are included in the price. Arena, equestrian center, holding pens, round pens, stable/barn, storage building, and a workshop with electricity are among the outside features. Building Information: Barn(s), electric to barn, equipment barn, hay barn, indoor arena, living quarters, and other buildings Loaf Shed(s), Stable(s), Tack Room, Wash Rack, and Water to Barn are all included.

Security features include: Detector for the detection of smoke Heating options include central air-electric, central heat-electric, and propane. Ceiling fans are among the energy-saving features available.

Property Features

Lot Dimensions: 248 Acres Dimensions of the property: more than 100 acres Horses permitted on this property; some trees; a tank/pond; and plenty of space. Waterfront:No Docking is not permitted. No, there is no lake pump. Buildings on the exterior: Bunk House Topography:Level Utilities include an all-weather road, overhead utilities, a septic system, and a well. Utilities: Electricity and phone service are available. Propane gas, an off-site generator, and a septic system are required. Take Interstate 35 north to FM 1202.

Continue on the service road after passing the FM 1202.

Tax and Financial Info

Restriction: There are no known restrictions (s)

Listing Agent/Office

Listed with the assistance of David Burgher of Briggs Freeman Sotheby’s International Realty.


Please be patient while the page loads.

Schedule a Tour

Schedule a TourWhile the MLS and NTREIS believe the information to be valid, they cannot guarantee its accuracy. In order for the information to be useful to consumers for their personal, non-commercial purposes, it may not be reproduced, redistributed, or otherwise used for any purpose other than to identify prospective properties that consumers might be interested in purchasing, unless expressly authorized in writing by the provider. In addition to Texas Grand Realty, real estate listings owned by brokerage firms other than Texas Grand Realty are identified by the NTREIS IDX logo and further information about them includes the name of the listing brokerage company.

Texas Real Estate For Sale – Abilene – Austin – Dallas – Fort Worth – Fredericksburg – Houston

There is a problem with your search because the page you were looking for does not exist. This can occur for a variety of causes, including the following:

  1. The page you were searching for does not exist, we’re sorry for the inconvenience. This can occur for a variety of causes, including:

In the interim, please find below links to some of our most popular parts of our website.

Advanced Search

Search the Multiple Listing Service (MLS), which is a consumer database of properties for sale in Austin, Texas. Search for properties based on their price, location, or neighborhood features. Go to PROPERTY SEARCH to find out more.

Map Search

Do you like to search using a map? Our interactive map search will allow you to look for properties from the air, including those with Google Street View and Satellite View. Navigate to MAP SEARCH.

Community Guide

Are you looking to purchase a home in Austin, Texas? With a single click, you may access our Community Guide to see a list of the locations we specialize in, as well as search for Austin area real estate listings by community with a single click. Go to theCOMMUNITY GUIDE page.

Contact Us

Do you have a query, want further information on a property listing, or are you just unable to locate what you are searching for? We’re here to assist you, and we’ll assist you in locating the information you want. Please see CONTACT US for further information.

Leave a Comment

Your email address will not be published. Required fields are marked *