How To Unblock A Toilet With Septic Tank? (Solution)

If a clog is still present, you can mix baking soda and vinegar to form a natural drain cleaner that is safe for a septic system. Pour one cup of baking soda into your toilet, trying to get as much as possible in the hole in the center. After that has settled, pour two cups of white vinegar over the baking soda.

How do you unclog a toilet with a plunger with a septic tank?

Right after, with force, start pushing the plunger down multiple times without compromising the seal. After pushing the plunger a few times aggressively, pull it up swiftly to break the seal. The water should start flowing down the drain, which then means that your toilet is unclogged.

Will toilet flush if septic tank is full?

Toilets Flush Slowly When your septic tank is excessively full, your toilet may start acting odd. You might find that your toilet doesn’t fully flush or flushes very slowly and odd noises occur when you flush your toilet. These noises usually sound like gurgling or bubbling.

Why won’t my toilet flush with a septic tank?

A common indicator of septic tank problems is a toilet that’s slow to flush — or won’t flush at all — and a plunger can’t fix the issue. The tank may be full, or there could be a clog in the pipes. Slow Drains. Watch out for slow-draining sinks, showers, and bathtubs.

What can break down poop in septic tank?

Yeast helps actively breaks down waste solids when added to your septic system. Flush ½ cup of dry baking yeast down the toilet, the first time. Add ¼ cup of instant yeast every 4 months, after the initial addition.

How do you know if your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

1. Your Drains Are Taking Forever.
2. Standing Water Over Your Septic Tank.
3. Bad Smells Coming From Your Yard.
4. You Hear Gurgling Water.
5. You Have A Sewage Backup.
6. How often should you empty your septic tank?

Why is my poop stuck in toilet?

Unclogging the toilet full of poop by using hot water is an efficient method, but it requires your patience and enough time. Wait for 5 to 10 minutes while the poop starts softening. Then flush the toilet. If the bowl is still clogged, you should repeat the action by pouring hot water with dish soap into the toilet.

How do you know your septic tank needs emptying?

Here are some of the signs for which you should look.

1. Water puddling above the septic tank. So you noticed a small pool of water but it didn’t rain?
2. Drains moving slowly. If the drain is moving slowly when you flush the toilet, it could be due to a clog.
3. Bad smells coming from the septic tank.
4. The sewer has backed up.

How long does it take for poop to break down in a septic tank?

The bacteria take 2-4 hours to germinate and then begin to break down solid waste. If the temperature and conditions are favorable, then the bacteria will multiply to the maximum level that the environment will allow in about 2-4 days.

How do you unclog a toilet full of poop and water?

All you have to do is pour about two cups of household bleach into the bowl. Wait for it to dissolve the poop, then flush. You can repeat a few times until the entire toilet clog is gone.

How do you dissolve sludge in a septic tank?

How to Reduce Sludge in a Septic Tank Without Pumping

1. Install an aeration system with diffused air in your septic tank.
2. Break up any compacted sludge.
3. Add a bio-activator or microbe blend.
4. Maintain the aeration system.
5. Add additional Microbes as required.

How to Unclog a Septic Tank Toilet

Unclogging a toilet that is linked to a septic tank may be a difficult task since you cannot use chemical clog removers such as Green Gobbler or Drano Max Gel because these chemicals would destroy the enzymes and bacteria in your septic system that are necessary for waste breakdown. Some of these chemicals are so potent that they might really cause harm to your septic system if not used properly. When it is not possible to utilize drain cleaners or chemical clog removers, how can you go about unclogging your septic tank toilet without resorting to chemicals?

One of these is quite likely to be successful.

Toilet Plunger

When it comes to unclogging a septic toilet, the first option that has been proven time and time again is the use of a toilet plunger. First and foremost, it is critical to recognize that not all plungers are created equal. Some plungers are designed to be used in sinks, while others are designed to be used just in toilets. A toilet plunger differs from a sink plunger in that it does not have flat bottoms, and it is supplied with a flange that is designed to fit exactly into the curvature of the toilet bowl.

• You must use the proper plunger for the job.
• Plungers with a flange that folds into the rubberized plunging cup are common in this category.
• Ensure that you have covered the floor of your bathroom with old newspapers before you begin plunging.
• Once the plunger is depressed, release it.
• Following that, begin repeatedly pressing the plunger down with force to ensure that the seal is not compromised.
• After a few seconds, water should begin to flow down the drain, indicating that your toilet has been unclogged.
• Sometimes a blockage might be so stubborn that even a few plunges aren’t enough to remove it completely.

Plumbing Snakes/Augers

You should consider utilizing a plumbing snake or auger if using a toilet plunger did not work for you. You may purchase an auger at your local home improvement or hardware shop if you do not already have one. You can get away with using a cheaper snake or auger to get the job done, but you’ll run the danger of scratching your toilet bowl, so make sure you invest in a high-quality item. Start by uncoiling the wire end of the plumbing snake and inserting it into the toilet, if you have one available.

If the toilet does not unclog after several attempts with the plunger, continue to try a couple more times before giving up and calling a plumber.

Dishwashing DetergentHot Water

As previously said, you should avoid using any chemical uncloggers since they have the potential to do significant damage to your septic system. Even if the two previously described ways do not work to unclog your toilet, there are some DIY options that you may experiment with. To begin, measure up a teaspoon of dishwashing soap and pour it into the bowl with the other ingredients. Don’t go crazy with the amount of salt you use. From then, you want to let your toilet bowl in its current state for 10-15 minutes before flushing it.

Please keep in mind that the water should not be heated over the boiling point of water (212°F), since boiling water can actually harm or shatter your toilet bowl if it gets too hot.

If you’re pouring the water, avoid getting too near to the bowl since you’ll need the force of the pouring to be significant in order to drive the clog lower, which is why we recommend pouring at waist height.

There are multiple times that you will need to use this procedure before you will notice any benefits.

Baking SodaAcidic Liquid

Another tried-and-true natural approach for unclogging a toilet is to combine baking soda with any acidic liquid, especially white vinegar because of its exceptional cleaning characteristics. Lemon juice can be used as a substitute to vinegar, although it will not be as effective as vinegar in this situation. Using a spoon, scrape out some of the water in the toilet bowl before adding the baking soda to the bowl. Following that, add an amount of baking soda equal to approximately half a box on the baking soda, and then gently pour an entire bottle of vinegar on top of the baking soda, resulting in a bubbling chemical reaction.

In the meantime, you want to have a couple of gallon of water heated to just below boiling point and then pour it into the toilet while you are waiting.

Final Thoughts

We’re convinced that one of the procedures suggested above will be effective in unclogging your septic toilet system. If none of these solutions work, you’ll need to call a qualified plumber since the blockage may be located farther down the drainage system or one of the sewage line pipes may have been ruptured, among other possibilities.

What Does a Clogged Toilet Mean When You Have a Septic System?

No one enjoys the sensation of having a toilet that is always blocked. When your toilet refuses to flush, you have a serious problem on your hands, and it has to be addressed as soon as possible to avoid more damage. However, if your home is equipped with a septic tank rather than municipal water, a blocked toilet might signal the beginning of a far more serious problem. When you are connected to the municipal sewer system, having your toilet stop working is a nightmare in and of itself. No matter what sort of system you have, you will still need to locate and remove the clog, which will need you to spend some quality time with your plunger to accomplish.

• You still have to locate and clear up the clog that has been causing you problems, as well as seek for strategies to prevent it from recurring.
• Taking these factors into mind might result in a septic system that is no longer functioning properly in your backyard, as well as a large repair bill arriving in your postal box.
• When a holding tank reaches its maximum capacity, it may back up and block the toilet, preventing it from functioning correctly.
• Leaving your drain fields unattended for an extended period of time might cause damage and threaten the overall system.
• Some of the activities you do in your house might be contributing to the problem with your toilet as well.
• It may feel wonderful on your body, but it is not healthy for your septic system, which is why you should avoid using it.
• If you have a cat, you should never dump cat litter down the toilet, even if the litter manufacturer indicates that it is safe to flush.
• Your septic system must be properly maintained, and any indicators of trouble must be reported immediately to the appropriate authorities.

A toilet that does not flush or clogs on a regular basis is a major source of concern, and it is not something you can afford to overlook. To determine if your toilet is blocked, you must examine not just the toilet within your home, but also the toilet and septic tank outside your home.

Unclogging a Drain or Toilet Attached to a Septic System?

When unclogging a toilet on a septic system, it is important to take precautions to avoid using chemicals that might be harmful to the septic system. Having said that, it is normally possible for the homeowner to complete the task. This article contains information on unclogging a drain or toilet that is connected to a septic system.

3 Questions

Inquire about something The following are the questions posed by members of the community. Continue reading to see the responses offered by the ThriftyFun community, or submit a new question.

Question:Unclogging Toilet Hooked to Septic Tank?

The 8th of January, 2010 Do you know of anyone who has tried the soap and hot water approach to unclog toilets who has a septic tank? Is it possible that this might cause harm to your septic tank? By Billy Hicks, a resident of Rocky Mount, North Carolina

Answers

1st of January, 20101 This was beneficial to me. The Most Effective Response It is effective and will not cause harm. In truth, the vast majority of commercial items are not harmful to kids. Simply follow the directions on the container’s label. Reply Was this information useful? 1 Provide an answer to this question

Question:Cleaning a Drain on a Septic System?

The 28th of July, 2016 The drain in our kitchen is sluggish. If you have a septic tank, what can you use to clean it?

Answers

HelloBronze Post a Medal for All Time on the wall! This was useful to 107 people on February 27, 2017. Using a teakettle full of water, 1 cup of baking soda, and 1 cup of vinegar, I’ve had fantastic success with this method. Go to the drain and pour in the baking soda in its entirety, followed by the vinegar on top of it. Then, when the fizzy reaction has occurred, pour the full pot of hot water over the muck. This is also really beneficial in the toilet. JudyGold’s Post Medal for All-Time Excellence!

At Home Depot, you may purchase a zip-it, which is a little snake.

Provide an answer to this question

Question:Unclogging a Drain Attached to a Septic System?

The 6th of December, 2010 Is there anyone who can provide me some pointers on how to unclog a drain? Because we have a septic tank, it must be as natural as possible (we don’t want to kill the microorganisms). ByJacqui428

Answers

This was beneficial on December 6, 20100. Pour a package of baking soda down the drain and follow it up with a large pot of boiling water to clear the clogged drain. If it doesn’t work, you can try snaking the drain instead. This was proven to be useful on December 7, 20100. In addition, I have a septic tank and a drainage system. I’ve used sodium hydroxide (lye) numerous times without issue, so it’s possible that it might be of assistance. Provide an answer to this question ThriftyFun.Desktop Page |View Mobile Version of this page Disclaimer|Privacy Policy|How to Get in Touch Cumuli, Inc.

How do you unclog a toilet from a septic tank?

Asked in the following category: General The most recent update was made on the 9th of January, 2020. You may combine baking soda and vinegar to create a natural drain cleaner that is suitable for use in an aseptic system if a clog is still present after cleaning. Pour one cup of baking soda into your toilet, making sure to get as much of it as possible into the hole in the center of the toilet bowl. The most frequent cause of a clogged septic tank is when you flush the toilet and water rises up in the tub or shower or into a fixture on a lower floor of the house after you flush.

• Pumping out your septic tank is necessary.
• Please wait a few minutes.
• Baking soda and vinegar react together to produce bubbles, so be sure to pour slowly and carefully to avoid splashing or overflowing the toilet water when you flush.
• Take one sheet and submerge it in the water for 2 seconds flat on its back.
• If it almost completely dissolves, it will be safe to use in the septic tank.
• To the contrary, all Drano®products are septic-safe drain cleaners that will not disturb or interfere with the natural bacteria in septic systems.

Drano®Max Build-Up Remover should be used on a monthly basis to replace the bacteria in the septic system that aid in the breakdown of toilet paper and organic debris in the pipes.

Best septic-safe way to unclog a toilet?

Ars Tribunus AngusticlaviusTribus: Up, down, left, right. you know the rest.Registered: Jun 8, 2000Posts: 7951

We have a clogged toilet that is resisting rectification.I went to the store to get some Liquid Plum-r yesterday but for the first time ever noticed that most of those types of products warn on the label not to use in toilets.So, wanting to be cautious so as not to possibly have a plumbing problem, I got something that was mostly sulfuric acid and said it was safe to use in toilets and with septic tanks.Well, that didn’t work.The clog doesn’t completely close the pipe; water can drain through, albeit very slowly, but I assume that the product is not as effective since it’s not having as much time to work on the clog as it would if the pipe were more fully closed.Does anyone have any (relatively cheap) suggestions for unclogging a toilet?Should I just go back and get some Liquid Plum-R?We’ve used that before in toilets and (to my knowledge) without any ill effects.Why don’t they want you to use it in toilets?

Common Septic Issues

The question was submitted to the category of General. The most recent update was made on January 9th, 2020. You may combine baking soda and vinegar to create a natural drain cleaner that is suitable for use with an aseptic system if a clog is still present after cleaning. Pour one cup of baking soda into your toilet, making sure to get as much of it into the hole in the middle as possible. The most frequent cause of a clogged septic tank is when you flush the toilet and water comes up in the tub or shower or into a fixture on the lower level of the house after you do.

1. Pumping out your septic tank is essential.
2. is a legitimate question.
3. Keep your patience for a moment or two longer.
4. To avoid toiletwater splashing or overflowing because of the reaction between baking soda and vinegar, pour gently and carefully to avoid creating bubbles.
5. Float one sheet in the water for 2 seconds, then remove it and repeat the process.
6. As long as it is practically dissolving, it will be safe to use in the septic system.
7. To the contrary, all Drano®products are septic-safe drain cleaners that will not disturb or interfere with the natural biological action of septic systems.

• Inspections and certifications of septic systems
• Pumping of septic systems Maintenance plans including service reminders for one, two, and three years
• Installations
• Repairs
• And line cleaning
• Water jetting at a high rate of speed
• Camera on the first row
• Service reminders for one, two, and three years
• Tank and pipe finding services in the underground
• Cleaning of the filter
• Septic service firm with one-stop shopping
• Lowest prices

To place an order for residential Septic Tank services, please email us. Superior Septic Service LLC is completely insured and bonded, and we are dedicated to providing the greatest customer service while also being environmentally conscious and concerned about our neighborhood. Septic System OdorsThere are various sites within an onsite system where odor might be a problem, including the septic tank.

1. Within the home
2. In the vicinity of the septic tank
3. In close proximity to a pretreatment unit
4. In the vicinity of the soil treatment area
5. Outside, in the garden

1. There are odors in the house. The presence of odors in a home is usually an indicator of a plumbing problem. When a trap in a basement floor drain dries out, gases from the septic tank are allowed to seep back into the residence, which is a fairly typical problem. Solution: Ensure that all floor drain traps are frequently refilled with fresh water. In addition, the cleanout access plug within a drain may be unfastened, allowing sewage gas to escape into the environment. One of the most prevalent problems is the plumbing vent placed on the top, which is responsible for allowing the pressure in the drainpipes to equalize as wastewater passes through them.

1. During particularly cold weather, these plumbing vents may get frozen shut, or they may become blocked with leaves or other debris.
2. 2.
3. As a preliminary step, check to see that all manholes and risers are properly covered if there is a particularly strong stench in the vicinity of the septic tank(s).
4. The manhole for the septic tank can be covered with a maximum of 12 inches of earth or it can be exposed to the surface.
5. They must also be securely fastened in place with lag screws or other types of fasteners as necessary.
6. This seal will need to be changed when the maintenance has been completed.
7. The presence of odors in close proximity to a pretreatment unit If an odor is persistent in the vicinity of one of these pretreatment units, a qualified onsite specialist who is familiar with the specific type of unit should be contacted for assistance.

The presence of odors in the vicinity of the soil treatment area There may be a problem with a section of the system if there are strong scents in the soil treatment region (for example, surrounding an in-ground drain field, bed, or mound).

A visual check of the entire region should be carried out in order to detect whether there are any damp or spongy soil patches that indicate that sewage is coming to the surface from beneath the ground.

A public health threat has been identified, and quick action should be taken to address the situation.

Odors emanating from the yard You should investigate whether the plumbing vent pipe (mentioned in1 above) on your house or on a neighbor’s house needs to be lengthened in order to distribute the septic gas odours across the yard.

If there is a strong wind blowing over a house, the air currents that are designed to move gases up and away might instead convey sewage gas into the yard.

In order to spread scents, the vent pipe should be extended to the outside of the home and out of sight. For added odor control, carbon filters can be installed on top of the vent to assist absorb odors. For the filters to be effective, they must be replaced on a regular basis (every 1 to 5 years).

How to Unclog Your Septic Tank

1. The presence of odors in the home. 2. In most cases, foul odors in a home indicate the presence of a plumbing issue. When a trap in a basement floor drain dries out, gases from the septic tank are allowed to seep back into the residence, which is a relatively typical situation. Solution: Ensure that all floor drain traps are frequently refilled with fresh water. Another possibility is that the cleanout access plug within a drain is faulty, allowing sewage gas to escape. The presence of a plumbing vent on the roof, which allows the pressure in the drainpipes to equalize as wastewater runs through them, is a second typical source of frustration.

1. It is possible for these plumbing vents to become blocked with leaves and other debris during extended cold seasons.
2. 2.
3. However, if there is a particularly strong stench in the vicinity of the septic tank(s), the first action should be to ensure that all manholes and risers are well covered.
4. Depending on the situation, the septic tank manhole can be covered with up to 12 inches of earth or it can be exposed to the elements.
5. Lag screws or other types of fasteners must be used to firmly hold them in place as well.
6. Upon completion of the maintenance, this seal will need to be replaced.
7. If an odor is persistent in the vicinity of one of these pretreatment units, a qualified onsite specialist who is familiar with the specific type of unit should be contacted for assistance.

The presence of odors in the vicinity of the soil treatment facility There may be a problem with a section of the system if there are strong scents in the soil treatment region (such as around an in-ground drain field, bed, or mound).

If there are any moist or spongy soil regions, it is necessary to do a visual assessment of the entire area to establish whether or not sewage is coming to the surface.

A public health threat has been identified, and quick action should be taken to address the issue.

Smells in the back yard.

The wind patterns that blow across valleys, wooded regions, and low-lying places may not be optimal for dispersing smells away from the living spaces and yard.

In order to spread scents, the vent pipe should be extended to the outside of the house. For added odor control, carbon filters can be installed on top of the vent to assist trap the odors. If you want your filters to remain effective, you must replace them on a regular basis (every 1 to 5 years).

1. 1 Check the inflow pipe by lifting the access cover of the tank that is nearest to your residence. The plastic or concrete cover in your yard that is closest to your house should be the first place you look. Carefully raise the cover of the tank up and away from the tank so that you can see what’s within. If you notice a white or green pipe at the end of the tank closest to your home, look for anything that could be blocking the pipe’s outlet. If there is, it is possible that the blockage is the source of the problem.

• Assuming the water level is below the level of the entrance pipe, the blockage might be located in the drain pipe that runs between the septic tank and your residence. If the water level is higher than the inlet but there is nothing blocking the end of the pipe, the clog is most likely in the leach field
• However, this is not always the case. It may be necessary to dig up the access lid with a shovel or raise it with a pry bar in order to get access.

• Advice: If you are unable to locate the access lid for your septic system, consult with your home’s as-built plans, which are blueprints prepared after your home is constructed, or with a professional septic service. 2 If the scum is trapped at the end of the input pipe, use a pole or a stick to push it out of the way. The scum layer is composed of solid waste that accumulates on the surface of the septic tank. Make use of a long, strong piece of wood or metal to slide the scum down or to the side of the entrance pipe as needed. Continue to remove as much scum as you can from the area around the pipe so that it can continue to fill your tank.

• If you are working in your septic tank, you should always wear gloves to prevent bacteria and waste from getting on your hands. If water starts to flow out of the pipe after you’ve pushed the scum out of the way, you’ve successfully eliminated the clog.

• Advertisement
• s3 If the blockage is deeper inside the pipe, use the pole or stick to probe the end of the pipe. Insert the end of the stick or pole you’re using as far as it will go into the end of the pipe you’re working with. Make use of the end of your probe to scrape the edges of the pipe and draw any waste from the pipe into the tank. Even if the clog is at the very end of the pipe, you should be able to dislodge it and get the water flowing once again. It is likely that the clog is located deeper inside the pipe if water does not flow out of it.

• Depending on where the pipe is located, you may or may not be able to insert your probe into the pipe.

• Depending on where the pipe is located, you may or may not be able to insert your probe.

• If at all possible, take a shower or bath as soon as possible after working on your septic tank
• When you wash your garments, use bleach or laundry sanitizer to ensure that no bacteria is left on them after washing.

• 5 If you were able to resolve the issue, replace the access lid on the septic tank. Lift the lid and place it over the opening that leads into the septic tank to prevent it from closing. Slowly drop the lid down until it fully covers the hole and does not move around any more. Continue to leave the lid open in order to insert a mechanical auger if you haven’t removed the blockage.

• Never leave the septic tank door open while you aren’t working on it to prevent anything from falling into the tank.

• 6 Make use of a reputable service. If your tank was completely filled, you should pump it within 5 days. It is conceivable that your tank will back up again even after you have removed the clog. This is especially true if your main tank is completely full to the entrance line. Inform septic service personnel that the scum level has reached the pipe by contacting them through telephone or email. It is best to schedule them within the following 5 days, otherwise you will increase the likelihood of septic fluid returning up the drainpipes. The service will drain your septic tank, ensuring that scum does not re-enter your plumbing system.

• Having a septic tank pumped typically costs between $75 and $200 USD, depending on the size of the tank and the amount of waste that has to be removed. Every 3–5 years, or whenever the tank becomes full, have your septic tank cleaned and emptied.

1. In order to get to the inflow line, you must first remove the septic tank access lid that is closest to your residence. Because the intake pipe is more likely to be located on the access lid nearest to your home, if your septic tank has multiple access lids, select the one that is closest to your home. Using your hands, lift or pull the tank’s cover off and set it aside while you continue to work. Inside your tank, look for the end of a white or green pipe that protrudes from the side that is closest to your house.

• If you are unsure about the location of your tank’s access lids, consult your home’s as-built plans or consult a professional service.

• 2 Insert the cutting blade of a mechanical auger into the jammed pipe’s end with the auger’s handle. A mechanical auger is comprised of a long metal cable that is inserted into your pipes and equipped with a revolving bit that cuts through the obstruction. Begin at the end of the blocked pipe or at an access point for the pipe, such as a cleanout port, to unclog the blockage. Placing the cutting blade of the auger inside the obstructed pipe and pushing the line in around 1–2 feet (30–61 cm) can clear the blockage.

• It is possible to purchase a mechanical auger either online or from a local hardware shop. Investigate whether your local hardware shop provides equipment rentals to see if you can borrow an auger for the day without having to pay the whole price

• A mechanical auger may be purchased either online or from a local hardware shop. Investigate whether your local hardware shop provides equipment rentals to see if you can borrow an auger for the day without having to pay the whole price
• And

• It’s possible that you’ll require an extension cord to connect the mechanical auger. You should never use the auger without wearing gloves or wearing safety eyewear since you might suffer a serious injury. Because the auger would spin violently if you start it with the cutting end outside of the pipe, you should never do so.

• 4) Continue to feed the auger deeper into the pipe until the obstruction is broken apart. Holding the auger’s line with both hands, guide it into the pipe until you encounter resistance if necessary. Try rotating the line in your hands to see how far it will travel within the pipe if the resistance feels substantial. It is possible that it has encountered a curve in the pipe. To drive the obstruction apart if this is not possible, use short, back and forth strokes to push and pull the auger. Continue to force the auger into the blocked piece of pipe until it is able to pass smoothly through it

• Feed the auger further into the pipe each time to ensure that the clog is broken apart. Continue to guide the auger’s line into the pipe with both hands until you encounter resistance. Try rotating the line in your hands to see how far it will travel within the pipe if the resistance feels substantial. It is possible that it has encountered a curve in the pipe. Other than that, use short back and forth strokes to push and pull the auger to break up the clog. Attempt to force the auger into the jammed piece of pipe until it is able to travel freely through it

• 4 Continue to feed the auger deeper into the pipe until the obstruction is broken apart. Using both hands, guide the auger’s line into the pipe until you encounter resistance. Because it is possible that the line has reached a curve in the pipe, try rotating the line in your hands to see if it travels further inside. Otherwise, use short, back-and-forth strokes to push and pull the auger to drive the obstruction apart. Continue to force the auger into the obstructed piece of pipe until it slides freely through it

• 4 Continue to feed the auger farther into the pipe, allowing it to break apart the obstruction. Hold the auger’s line with both hands and move it through the pipe until you encounter resistance. If the resistance seems substantial, try rotating the line in your hands to see if it travels farther within the pipe, as it may have encountered a curve in the pipe. Otherwise, use short, back and forth strokes to push and pull the auger to drive the obstruction apart. Continue to force the auger into the blocked piece of pipe until it is able to pass through it effortlessly

• 6 The tools should be cleaned with a solution made up of 5 parts water and 1 part bleach. Stir the solution together by pouring 1 part chlorine bleach and 5 parts clean water into a bucket and mixing thoroughly. Clean the end of the auger with a cleaning rag to eliminate any germs that may have remained on the surface and avoid contaminating other parts of the machine. You should drain the solution into your septic tank after you’re finished

• 6 The tools should be cleaned using a solution composed of 5 parts water and 1 part chlorine bleach. Stir the solution together by pouring 1 part chlorine bleach and 5 parts clean water into a bucket and mixing well. To avoid contaminating anything else, wipe off the end of the auger with a cleaning cloth to remove any germs that may have been left on the surface after it was cleaned. When you’re finished, drain the solution into your septic tank.

1. 7Remove the septic tank’s cover and replace it. Lift the lid off the ground by grabbing it by the handles or the sides of the container. Lift and carefully drop the lid back onto the opening going into your sewage treatment system until it is completely enclosed. Make sure the lid does not slip or shift in any way, or otherwise it may break loose and fall off the septic tank. Advertisement

1. 7Remove the septic tank’s cover and close it. Lid should be lifted off the ground by the handles or sides of its rim. Lift and carefully drop the lid back onto the hole going into your sewage treatment system until it is completely covered. (See Figure 1). Take care to ensure that the septic tank lid does not slip or shift, since this might cause it to fall off easily. Advertisement

• Using strong chemical cleansers down your drain is not recommended due to the possibility that they can destroy the natural bacteria in your septic tank that is responsible for decomposition of solid waste. You should never pour cooking oil down the drain because it might harden in the pipes and cause blockages that are difficult to clear.

• As a reminder, you do not need to add any additional natural enzymes or bacteria to your septic tank in order for it to properly break down solid waste. Any additional enzymes will be ineffective in comparison to the enzymes that naturally present in the tank
• 2 Reduce the amount of water you use in your home so that the septic system can drain correctly. Avoid running water in your home until absolutely necessary, since doing so may cause the tank to fill up too rapidly and overflow. Use as little water as possible when bathing or cleaning, so that you only have as much as is necessary at any one time. In the event that you have any outdated or leaking fixtures, you should repair them or replace them with more energy-efficient systems, such as toilets that flush less water or faucets with aerators.

• It will also save you money on your utility bills if you keep your water consumption to a minimum.

• 3 Avoid driving or planting over the area where your septic tank is located. Heavy weight can cause pipes going from your septic tank to collapse or break, so if at all possible, avoid driving over the region in a vehicle as much as possible. Plant roots can also grow into the pipes or septic tank, causing them to clog more quickly than they otherwise would. Maintain a distance of at least 20–30 feet (6.1–9.1 m) between your septic system and any trees or plants you intend to plant so that the roots are not able to grow within.

• Even if you use a mechanical auger to remove the roots out of your pipes, the roots will come back if the problem is not addressed. Root barriers purchased from gardening supply stores destroy roots on touch and can help to prevent overgrowth in your septic system. To protect your septic system from pipes, dig a trench around it that is 2 feet (61 cm) deep and 3 feet (91 cm) away from them. Make sure that you place the root barrier in the trench vertically before you fill the trench back up with earth.

• 4 Improve drainage by cleaning the effluent filter located on the outflow pipe. The effluent filter is a plastic cylinder that is installed in the exit line of your septic tank to prevent solid waste from escaping. Make sure the tank closest to your home has an access cover that can be opened. Look for a vertical white or green pipe that holds the filter and protrudes through the top layer of scum on the interior of the filter. Remove the filter from the vertical pipe by pulling it straight out and rinsing the waste back into the tank using a hose. Push the filter back into the pipe so that it may continue to prevent waste from escaping

• Not every septic system will be equipped with an effluent filter
• However, most will. Check your filter every time you have your tank pumped or examined to ensure that it does not become clogged.

1. 5. Have a professional inspection of your septic tank performed once every three years. Septic tanks typically take 3–5 years to fill, however this might vary based on the size of the tank and the quantity of water it receives. Consult with a professional provider to have the water levels and pipes for your system checked to determine if any adjustments are necessary. If the provider has any issues, you should solve them as quickly as possible to avoid having a malfunctioning septic system later on. Advertisement

Create a new question

• Questions can be added at any time.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

• Unless you are skilled in septic tank unclogging or there is significant damage to the pipes, you should hire a septic specialist to conduct the necessary repairs for you to guarantee that everything is in compliance with the law. When working on your septic tank, always use protective eyewear and disposable gloves to prevent contamination.

Unless you are skilled in septic tank unclogging or there is significant damage to the pipes, you should hire a septic specialist to conduct the necessary repairs for you to verify that everything is in compliance with local codes. If you are working on your septic tank, you should always use safety eyewear and disposable gloves to prevent contamination.

Things You’ll Need

• Hose
• Paper towel
• Mechanical auger
• Safety glasses
• Work gloves

About This Article

The writers of this page have together authored a page that has been read 315,143 times.

Did this article help you?

Unclog your toilet and protect your septic tank from further damage using wikiHow – The How-To Manual You Can Edit Clogged toilets happen at the most inconvenient times, and they tend to happen at the most inconvenient times. Fortunately, most blockages may be cleared without the need for a professional plumber’s assistance. If you follow these procedures, you should be able to resolve the situation before your in-laws arrive for dinner.

Steps

1. Only flush the toilet once. If it doesn’t flush the first time, don’t flush it a second time. This will result in more water being pushed into the toilet bowl as a result of this. Let the water in the bowl rest for a time
2. It should eventually drain at least a little amount, albeit at a snail’s pace in some cases. Put on a pair of rubber gloves to protect your hands. However, even though toilets are naturally unclean places to work, a decent pair of rubber cleaning gloves will keep you safe from the bacteria that lurk inside. Preserve the condition of the floor. What could possibly be worse than a blocked toilet? A toilet that is overflowing. Preventing or stopping overflow as soon as possible will help you avoid an unpleasant mess and damage to your home. Newspapers should be placed on the floor. There is a good chance that you may make a few minor splashes and spills when unclogging the toilet. It is advisable to place several layers of newspaper around the toilet to protect the floor. Check to see that the water supply to the toilet is turned off. It should be situated just behind the toilet, and it has the appearance of a standard faucet knob. Keep the water supply to your home from being turned off, since this will prevent others from taking use of the resource. If the water is turned off to the toilet at the very least, this will avoid the bathroom getting flooded.

Method Using Dish Soap and Hot Water

1. Pour a little amount of dish soap (a few squirts) into the toilet tank. However, if you live in an apartment complex, you should be cautious about adopting this strategy. Put in half a bucket of extremely hot water (NOT boiling water–this can dissolve vital seals) from approximately waist level and pour it into the bowl with a pot on top. Ideally, the water should not be hotter than a hot cup of tea that you can safely drink
2. Nonetheless, a little amount will not enough
3. Rather, you want to elevate the temperature of the water traveling around or pushing on the clog. Allow for a few minutes of contemplation. If the water level has not decreased after several attempts, repeat the procedure or go on to the plunging approach. The addition of warm water to a clog (not boiling hot) will sometimes loosen and eliminate the obstruction on its own
4. However, this should only be done in extreme cases.

The Plunger Technique If you are certain that an object (such as a child’s toy) is the source of the clog, you can skip the plunging step and go to the next step.

1. Method of the Plunger You can skip the plunge and move right to another option if you know there’s an object (such as a child’s toy) causing the blockage.

Method Using a Wire Coat Hanger If plunging does not work to unclog the drain, a wire coat hanger may be used to dislodge the blockage.

1. Remove the coat hanging from its hook. Separate the coat hanger’s upper ends by twisting them apart until they are no longer linked. One end of the wire should be inserted into the drain. In order to clear the drain, twist and push the wire into the drain while maneuvering in a circular motion with your hands. This will usually work if there is an obstruction in the first several inches of the drain
2. However, it may not always work.

Method of Using a Plumbing Snake A snake (also known as a “auger,” “flexible cleaning tool,” or “flexible cleaning tool”) is a flexible coil of wire that can “snake” between the bends of a drain and reach deeper levels than a wire alone.

1. Technique Using a Plumbing Snail A snake (also known as a “auger,” “flexible cleaning tool,” or “flexible cleaning tool”) is a flexible coil of wire that can “snake” between the bends of a drain and reach deeper levels than a wire alone can achieve.

Method of Using a Snake in the Plumbing A snake (also known as a “auger” or “flexible cleaning tool”) is a flexible coil of wire that can “snake” between the bends of a drain and reach deeper than a wire alone.

Video

Unclogging a toilet is a simple task when you have the correct equipment. To unclog a toilet without flooding your bathroom, Julie Sussman and Stephanie Glakas-Tenet demonstrate their technique.

Tips

• If nothing seems to work, it’s possible that you have an issue deeper in the plumbing lines, and you’ll need to hire a plumber to fix it. While it is likely that you will be able to remove the blockage yourself, you will have at the very least demonstrated your commitment to the cause by fighting the good fight. After you’ve dislodged the clog from the toilet bowl, disinfect it using a disinfectant cleaner to prevent future clogs. Do not use bleach because if you pour it down the toilet and flush it, it will combine with the sewage and generate fatal carbon monoxcide. Remove the wire (if it was used) and disinfect or discard the rubber gloves, as well as any other equipment (such as a plunger or a snake) that you may have employed. If not properly cleaned, these tools have the potential to transmit germs and emit a foul odor. After plunging, a used plunger (particularly one of the flange plungers listed above) may still have water trapped inside of it. Keep it over the toilet, turn it a little, and shake it a little to drain it so that it doesn’t leak on the ground. In the event that you need to halt the flow of water into the toilet bowl at any moment, you may do so by either opening up the toilet tank and lifting the float arm, or by turning the toilet valve off (which is normally placed behind or to the side of the toilet). When the float is raised over a specific point, the water will come to a halt. It will continue as soon as you release your grip on the arm. If you can see what is causing the clog, put on a pair of rubber gloves and try to remove it from the toilet if at all feasible
• Otherwise, call a plumber.

Warnings

• Because it is unnecessary and will result in splashing, you should avoid pushing or pulling the plunger aggressively while it is in the toilet bowl. Drain-cleaning chemicals are typically exceedingly toxic and detrimental to human health and the environment. Avoid contact with the skin and eyes, and do not combine different chemicals together. Make sure you follow all manufacturer directions to the letter, and pay attention to any cautions. When it comes to toilet cleaning products, the majority of those sold in retail stores are not designed for this purpose. Check the product label to check that the product is compatible with toilet drains before using it.

Things You’ll Need

• A plunger, optional dish soap, rubber gloves, an optional wire hanger, an optional pail, and newspaper are all good additions.

Related wikiHows

• To turn off the water supply to a toilet, follow these steps. To fix a running toilet, follow these steps. Learn how to clean a toilet using Coca-Cola. Any toilet may be converted to a low flush toilet with a few simple tools.

Sources and Citations

• VideoJug.com Unclogging a toilet is demonstrated in this video. This article’s original source may be found here. This information has been shared with consent.

The information in this article was supplied by wikiHow, a wiki how-to manual. It is recommended that you change this page and include author credits from the original wikiHow article on How to Unclog a Toilet. Unless otherwise stated, all content on wikiHow is available under a Creative Commons license. So far, there has been one comment. Please leave a remark.

SEPTIC PROBLEMS THAT CAN MIMIC DRAIN CLOGS

A wiki how-to manual is used to create this article. It is recommended that you change this article and include author credits from the original wikiHow article onHow to Unclog a Toilet. Creative Commons licenses are granted to all of the content on WikiHow. As of now, there has been only one comment. Specify your thoughts in the comments section

Clogged Drain or Clogged Septic Tank?

Robs Septicon is the author of this piece. Postings under Uncategorised A blocked septic tank can cause difficulties that are quite similar to those caused by a clogged drain. Knowing the difference between the two might assist you in taking care of your house. Here’s all you need to know about the situation. When a septic tank overflows, why do drains become clogged? The septic tank is a holding tank that is located underground. All of the wastewater from the house flows into the septic tank, which steadily fills up with garbage over time.

Towards the top of the tank, there is a pipe that flows into the yard, into an area known as the drain field, where the tank is located.

The dirt filters the water and kills the bacteria that are there.

It is possible for the septic tank to fill up without any water draining out if the line feeding into the drain field becomes plugged.

As the water rises via the main line, the capacity of fixtures in the house to drain correctly diminishes.

The drains will become sluggish if the septic tank is just half blocked, as the water strains to make its way down into the septic tank.

What Are the Signs of a Septic Tank Clog?

It might be difficult to detect the difference at times.

Due to the fact that they are the most closely associated with the septic tank, the lower drains in the home will be affected first when the septic tank overflows.

In addition to being more sluggish, they may begin to produce unusual noises, such as gurgling sounds, as they age.

Local clogs often only impact a single fixture or a small number of fixtures that are linked to it.

If all of the other fixtures in the house are operating properly, this is an indicator that there is a blockage in the house rather than in the septic tank itself.

A blockage in a septic tank should not be repaired by someone who has just rudimentary expertise or who lacks the necessary instruments.

In certain cases, you may be able to address the problem yourself if you suspect that the blockage is in the pipe rather than in the septic tank.

Allow for an hour or two for the mixture to settle in the pipe before using it.

Depending on how large the blockage is, this may be sufficient to empty the pipe.

An auger is made out of a long, rigid cable with a pointed, twisting end at the other end.

A plumber may be required if neither of these approaches proves effective in clearing the clog from the drain.

Chemical drain cleaners have the potential to harm beneficial microorganisms in your septic tank, which might lead to another clog in the future.

Clogs in septic tanks can arise for a number of different causes.

Many septic tanks require pumping every three to five years, depending on the size of the tank.

Exactly What Should You Do If You Suspect You Have a Septic Tank Issue?

An inspection by a septic tank firm will allow them to determine whether or not the tank needs to be drained.

Rob’s Septic Tanks, Inc. can provide you with further information on clogs and septic tanks. We’ll be pleased to answer any questions you have and provide you with further information.