How To Test A Liberty Septic Tank? (TOP 5 Tips)

Remove the septic tank cover. The cover of the tank will be at the end nearest the house. If the location of the tank is unknown, check the direction of the large wastewater pipe coming from the toilet.

How do I know if my septic pump is working?

To test if the pump is working, first turn the pump on by turning the second from the bottom float upside down. While holding that float upside down, turn the next float up (that would be the second from the top), upside down. You should hear the pump turn on.

How long does a Liberty sewage pump last?

On average, new ejector pumps last around seven to 10 years, but if you keep up routine maintenance and annual inspections, some ejector pumps can last over 20 years.

Why is my septic not pumping?

If the pump does not appear to be working at all, does not respond to any tests and is not pumping effluent, there may be a wiring problem. First check your circuit breaker, and then try to use a multimeter or similar device to check wires in the septic system for damage to see what needs to be replaced.

What does flashing red light on septic tank mean?

The red light indicates the alarm is receiving a signal from the pump tank that the water level is rising higher or is dropping lower than it should be. Next, check the septic breaker to ensure the system has power. Try to minimize water usage during this time.

Do all septic tanks have alarms?

All septic systems that use a pump to move wastewater from a septic pump tank to a drainfield or mound have an alarm installed in the house. The alarm goes off when wastewater is not being pumped from the septic pump tank to the drainfield or mound.

How do I know if my sump pump is clogged?

Observe the float and the triggering of the on/off switch and make sure that the water exits the basin efficiently. Pour another 5 gallons of water into the basin and again monitor the pump’s actions. If the system efficiently pumps water out of the sump basin, you have cleared the clog.

How much is a new pump for a septic tank?

Septic Tank Pump Replacement The average cost to replace a failed pump ranges between $800 and $1,400 including labor.

Where are Liberty pumps made?

These pumps are produced in Bergen, New York in a very efficient lean-manufacturing environment.

How do you tell if your septic tank is full?

How to tell your septic tank is full and needs emptying

Pooling water.

Slow drains.
Odours.
An overly healthy lawn.

Sewer backup.
Gurgling Pipes.
Trouble Flushing.

How do you unclog a septic tank?

Sprinkle the drain with baking soda, then dump vinegar into the pipe. Leave the mixture to sit in the pipe for an hour or two. Finally, flush the drain with hot water. If the clog is small, this could be enough to clear the pipe.

How do you unclog a septic drain field?

Can Anything Unclog an Old Septic Drain Field?

Shock the System With Bacteria. A septic system bacteria packet can help clean out a clogged drain field by allowing waste material to break down and drain through.

Reduce Water Usage.
Avoid Harsh Chemicals.
Change to Gentler Toilet Paper and Soap.

Contact a Septic Professional.

What does alarm on septic tank mean?

A septic tank alarm system is a device designed to monitor the water elevation inside the tank, and it alerts you when the water level in the tank is much higher or lower than it should be. This raises the water level inside the pump tank until the controls cycle back and come on again.

What does the alarm mean on my septic system?

When the septic alarm sounds, it tells you that there is a problem getting wastewater to the drain field. Several different things may cause this. Most septic tanks have an alert when there’s too much water inside of it and could cause some kind of backup or overflow if not dealt with promptly.

Will a flooded septic tank fix itself?

Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.

Videos

Liberty Pumps has released a corporate video! Return to the top of the page

WhyLibertyPumps?

Would you want to know what it’s like to work at Liberty Pumps? Our members will be able to tell you everything about it. Return to the top of the page

Sump Pumps

It is necessary to pump surplus precipitation or groundwater away from a certain location in order for the system to function properly. A sump pump is located within a basin (also known as a sump) that is used to collect the surplus water collected. Return to the top of the page

Sewage and Effluent Pumps

The most common application for an effluent pump is in septic tank systems. Gray wastewater (also known as effluent) is the water that remains after the particles have settled out. Return to the top of the page

Drain and Specialty Pumps

The drain pump from Liberty Pumps is used to pump the drain water from a sink, which is most typically utilized in laundry tray applications, to a collection container. Return to the top of the page

EPS

Engineered Pump Systems (EPS) are available from Liberty in a variety of designs. Simplex to duplex grinder and solids handling systems are among the products we provide, and we can customize a pump system to fit your individual application requirements. Return to the top of the page

Model 406

A small, silent drain pump that is ideal for installing in cupboards or drawers. For use with a variety of items such as bar sinks, laundry trays, dehumidifiers, utility sinks, showers, and other similar items. Return to the top of the page

EPS

Grinder Pumps

In a variety of configurations, Liberty provides Engineered Pump Systems (EPS). We can deliver the exact pump system to fulfill your task needs, ranging from simplex to duplex grinders and solids-handling systems. Return to the beginning of the page

ProVore

Residential grinder pump from Liberty Pumps with 1 HP capacity is now available! Designed for use in residential situations where the addition of a bathroom or other fixtures below sewage lines necessitates pumping, the Liberty Pumps ProVoreTM PRG-Series grinders are a new generation of grinders. With a 1 horsepower motor, the machine is intended to run on either 115 or 230 volts, and it may be connected to normal 20 amp wiring without modification. Using Liberty’s revolutionary V-Slice® cutter technology, the ProVoreTM shreds solids such as feminine products, rags, and other undesired material in a matter of seconds.

You may reach Liberty Pumps at 1-800-543-2550 or visit their website at for further information.

V-Slice Cutter

Liberty Pumps’ V-Slice grinding technology is seen in this montage of film. Return to the top of the page

EPS

Engineered Pump Systems (EPS) are available from Liberty in a variety of designs.

Simplex to duplex grinder and solids handling systems are among the products we provide, and we can customize a pump system to fit your individual application requirements. Return to the top of the page

StormCell® Features Video

Battery backup pumps provide high-quality protection for professionals. Return to the top of the page

AscentII

Liberty Pumps is proud to introduce the new Ascent II macerating toilet system to the market. The full solution for adding a bathroom in a practical manner to remodeling and addition projects. Videos on the overview, features, and installation are included. Return to the top of the page

Ascent II Overview

Liberty Pumps’ Ascent II Macerating Toilet System is now available for purchase. The comprehensive solution for the quick and easy addition of a bathroom in remodeling and expansion projects is available. Return to the top of the page

Ascent II Features

Install a restroom virtually anywhere with the Liberty Pumps Ascent II Macerating Toilet System Ruggedness Video. Return to the top of the page

Ascent II Installation

This video shows the installation of a Liberty Pumps Ascent II Macerating Toilet System Ruggedness. Return to the top of the page

Ascent II Razor Ruggedness

The Ascent II RazorCut Ruggedness Test is seen in this video. Return to the top of the page

Install Videos

Anywhere in the globe, you can keep track on what’s going on with your pump. Return to the top of the page

NightEye® Install Video

Anywhere in the globe, you can keep track on what’s going on with your pumps. Return to the beginning of the page

NightEye® App Set Up Video

Learn how to link your NightEye app to your NightEye alarm so that you may get notifications from any location! Return to the top of the page

Troubleshooting Pumps: The Pump Motor Doesn’t Run

Check the wires in the septic system for damage with a voltmeter or comparable gadget to determine whether or not they need to be replaced.

Interested in Pumps?

Get the latest Pumps articles, news, and videos delivered directly to your email! Now is the time to sign up. Pumps+ Receive Notifications Checking for faults with a septic pump’s electrical system, the pump itself, and its controls are all important first steps when it won’t start. Dealing with electricity may be extremely dangerous; thus, exercise extreme caution while working with electricity and turn off power supply breakers when testing components inside the electrical system. If you are not 100 percent sure in your ability to execute any of these tests safely, consult with a specialist before proceeding.

Electrical problems

If the pump does not appear to be operating at all, does not respond to any testing, and does not appear to be pumping effluent, it is possible that there is a wiring issue. Examine your circuit breaker first, and then try to use a voltmeter or similar equipment to check the wires in your septic system for damage to determine whether or not they need to be changed. If the wires are damaged, replace them.

A fuse has blown or a circuit breaker has been triggered on the circuit. Check the fuses and circuit breakers. Fuse replacement is necessary as needed. Take note of the pump manufacturer’s suggested size as well as the pump nameplate rating. In the event that a circuit repair is required, contact an electrician. The power cord for the pump is improperly connected and makes poor contact with the pump. The pump cable cap prongs should be checked for tightness and corrosion if the system is equipped with a piggyback plug in. Alternatively, replace the plug, clean the plug prongs with abrasive paper, or have the electrical receptacle changed

The branch circuit wiring is insufficient to support the pump load. Check the voltage on the line and compare it to the manufacturer’s standards if necessary. The pump should be hooked into a separate circuit breaker from the rest of the system (or fuse). If the circuit breaker also supplies electricity to other outlets or appliances, an additional outlet should be added so that the pump has its own circuit breaker as well. The pump motor overload tripped the circuit, which necessitated the call for an electrician. Allow the pump to cool for five to ten minutes before reconnecting it to the power source. If the overloadtrip occurs again, remedial action should be taken. Verify that the line voltage is within specifications by comparing it to the manufacturer’s specs. Check the voltage of the branch circuit with an electrician or with the power provider. Make sure that the pump is connected to a separate branch circuit since the voltage provided is insufficient. Voltagenmust be within 10% of motor ratings on either side of the equation. Check that adequate power is being sent through the system by measuring the voltage at the pressure switch, the control box, and any other components through which power is being delivered. a. If you notice that the electricity is too high or too low at the power panel, you may need to call the electric utility provider for assistance. Thermal overload and shutdown will occur as a result of low voltage at the pump. Call your local electrician to fix the circuit and, if necessary, contact your energy supplier. Check the controlpanel connections and watertightness as well. Look for clear evidence of flaws and wear on the control panel with a visual inspection. Check for faulty connections as well as burned or melted components. Perhaps your prior examination of the power supply at your control panel led you to the conclusion that a bad splice connection or broken conduit could be the source of your problem. Make a visual inspection of any electrical splice connections for corrosion and other visible evidence that power is not being delivered to the pump. It is important to ensure that the conduit, and thus the wire within it, has not been damaged (for example, if it has been struck by a lawn mower).

Pump problems

It is possible that the motor for the lift pump is not functioning properly, in which case power is still flowing to the pump but it is unable to function. At this stage, make sure that the pump is not clogged and that it is capable of performing its intended function; otherwise, the pump will need to be fixed or replaced totally.

Theimpeller has been blocked or restricted. Disconnect the power, remove the pump from the sump, and inspect it for freedom of rotation of the impeller and shaft. Clean the volute and impeller, and remove any obstructions
The bearings have frozen in their positions. Disconnect the power, remove the pump from the sump, and inspect it for freedom of rotation of the impeller and shaft. Lower bearing of the column pump should be free and lubricated. In order to repair the pump bearing, contact a licensed service shop. The water level is not sufficiently enough to activate the control switch. Water should be added to the sump to make it turn on. Control floats or weights must be readjusted
An internal motor problem exists. Pump should be removed, power should be disconnected, and rated voltage should be connected before the controlswitch is actuated. To have your vehicle repaired or replaced, contact an authorized service shop.

Float/control problems

In comparison to a float tree, a pump linked to a line is used. If the pump detects sewage levels using a float, the float may become caught or destroyed, in which case the pump will not operate.

Usually, you can adjust the float or otherwise correct it so that it floats normally again, but if the problem is severe enough, you may need to replace the float totally.

The operation of the float is hampered or restricted in some way. Water should be added to the sump to make it turn on. Make any necessary adjustments to the control floats or weights. If the float rod is bent or obstructed by debris, consider adding a separate float tree to make pump removal and float operation easier. If the float rod is bent or obstructed by debris, consider replacing it. Examine and keep an eye on things. Make necessary adjustments to the control floats or weights
The float switch is faulty. Remove the pump, turn off the power, connect the power to the rated voltage, and turn on the controlswitch. Inspect for deformation, charred or melted components, or a significant amount of black discoloration. Unplug the pump’s chord from the piggyback plug on the floatswitch, and then reconnect the cord. To test the pump, just put the plug straight into an electrical outlet. If the pump continues to run, the float switch has failed and must be replaced. (Do not keep the pump plugged in for an extended period of time or it may burn out.) Make any necessary adjustments to the control floats or weights. Replace the liquid level control with a new one. Give the pressure switch a thorough visual inspection to check for flaws and wear and tear. Turning on and off switches is essential for a fully functioning system, and they are reasonably priced.

a little about the author Sara Heger, Ph.D., is an engineer, researcher, and lecturer in the Onsite Sewage Treatment Program at the University of Minnesota’s Water Resources Center. She holds a bachelor’s degree in civil engineering and a master’s degree in environmental science. She has given presentations at several local and national training events on topics such as the design, installation, and administration of septic systems, as well as research in the related field. Her responsibilities include serving as the education chair for the Minnesota Onsite Wastewater Association and the National Onsite Wastewater Recycling Association, as well as serving on the National Science Foundation’s International Committee on Wastewater Treatment Systems.

Heger will respond as soon as possible.

This article is part of a series on troubleshooting pumps:

If the pump motor does not turn on, troubleshooting is necessary. Pump problems include: the pump turns on, but there is no water

The pump turns on, but there is no water. Pump problems include the following: the pump runs continuously or cycles too frequently
Pump problems include the following: the pump makes a lot of noise
Pump Troubleshooting: There is a strong odor of sewer gas

Does Your Septic System Require A New Pump?

A septic tank’s waste and sewage are evacuated from it and discharged into a drain field, either by gravity or with the assistance of a septic system lift pump. In most cases, a septic pump is not required if the waste can flow at a rate of at least two feet per second through the system using gravity alone. Pumps are typically required for septic tanks that are located lower than the drain field and for which gravity is unable to transport and/or force the effluent out of the tank due to its location.

Know If Your System Uses A Septic Effluent Pump Or Septic Grinder Pump

Knowing what sort of pump your septic system is equipped with is critical to the overall operation of the system. A septic effluent pump is a device that transfers waste from a septic tank to a drain field. A septic grinder pump is responsible for the grinding and movement of human waste and toilet paper. Septic tank businesses in Gainesville, FL such as Jones PlumbingSeptic Tank Service can help if you’re not sure what sort of pump the system is using or where it’s located in the system. Our professionals will identify the pump and check the septic system in order to notify you of the procedures that need to be taken in order to keep all components in proper operating order.

How Septic Pumps Work

A septic pump is a sort of submersible pump that is installed in either the last chamber of the septic tank or in a separate chamber outside the main tank of the system. As waste builds up in the chamber, it activates a float switch, which then activates the septic pump. After that, waste is forced up the outflow pipe and into the drain field by an impeller. Installing a septic tank pump alarm is an excellent strategy to avoid having to clean out your septic tank on a regular basis. One of our professionals will connect the float switch to an alarm panel, which will sound if the pump fails for any reason during the installation.

This alarm will ring and notify you if there is a sewage backup in your home.

Maintenance For A Septic Pump

The upkeep of a septic pump goes hand in hand with the upkeep of a septic system in its whole.

Never drain or flush any of the following common home objects to avoid the need for emergency septic service and to ensure the pump’s long-term functionality:

Baby wipes
Cat litter
Fats, oils, and/or grease produced by or utilized in the preparation of meals

Dental floss
Personal hygiene products
And Q-tips or other cotton swabs are all recommended.

In addition, avoid using the garbage disposal because this can cause the septic tank to fill up more rapidly and force water into the tank, among other things. If there is an excessive amount of water entering the septic system, it can cause sediments to enter the septic pump, resulting in a probable blockage in either the pump or the drain field. If or when this occurs, contact Jones PlumbingSeptic Tank Service for prompt and dependable septic tank repairs.

Common Septic Pump Issues

In addition, avoid using the garbage disposal because this might cause the septic tank to fill up more rapidly and force water into the tank as a result. Excess water entering the septic system can lead to the accumulation of sediments in the pump, which can lead to a potential blockage in either the pump or the drain field. When or if this occurs, contact Jones PlumbingSeptic Tank Service for prompt and dependable septic tank repair services.

Noise Or No Noise

There are occasions when it is possible to hear the septic pump operating within the chamber itself. Do not hesitate to contact us for septic service if it appears that the pump is having difficulty or is failing to transport waste effectively.

Leaking Into The Septic Tank

The septic pump is equipped with a check valve, which provides a pressure gradient in order to keep the waste flowing through the pump and into the drainage system. Whenever the valve wears down or breaks, waste is forced back into the septic tank, causing the tank to overflow and back up into the pipes.

Faulty Float

Floats can become stuck open or closed, or they might become damaged as a result of material entering the septic tank. Depending on the extent of the damage, a professional from Jones PlumbingSeptic Tank Service may be able to remove the debris or may need to replace the float entirely.

Burnt Out Motor

If the motor within the septic pump burns out or fails, the pump will be unable to transfer waste, even if the energy is still being supplied to the device, since the waste would be trapped. In most cases, replacing the pump will address the problem.

Installing A New Septic Pump Or System

Jones PlumbingSeptic Tank Service will replace your septic tank if it is essential, and they will also install a new pump. Everything begins with an application, which is needed by the Florida Department of Health. We will always assist you in filling out the application and applying for any permissions that may be required. Our professionals will be pleased to walk you through the procedure and answer any questions you may have along the way.

Septic Tank Service

Jones PlumbingSeptic Tank Service can solve any septic issue, regardless of whether your sewage system currently has a pump or if you’re interested whether installing a pump will increase the system’s overall efficiency. When performing septic tank repairs in Gainesville, our specialists take into consideration the demands of the family or company. Call Jones PlumbingSeptic Tank Service immediately to make an appointment for septic service!

The Best Sewage Pumps of 2022

If you purchase a product after clicking on one of our affiliate links, BobVila.com and its partners may get a commission. Image courtesy of depositphotos.com Septic systems are used to handle waste in homes that are not connected to municipal sewage systems. It is necessary to utilize an efficient wastewater pump in order to transport wastewater from a residence to the wastewater treatment system. To the contrary of effluent pumps and sump pumps, which only move water, sewage pumps are capable of transporting wastewater with particles up to 2 inches in diameter.

They are made of a sturdy cast-iron construction that can withstand the corrosive environment of a wastewater treatment basin.

This article will go into great detail on what characteristics are critical to consider when searching for a sewage pump, as well as examining some of the best models currently available on the market.

The Zoeller 267-0001 M267 Waste-Mate Sewage Pump is the best overall choice. Liberty Pumps LE51A LE50-Series Sewage Pump is the runner-up in this race. THE BEST VALUE FOR MONEY CAN BE FOUND: Superior Pump 93501 Cast Iron Sewage Pump with 1/2 horsepower

Image courtesy of Amazon.com

What to Consider When Choosing the Best Sewage Pump

In addition to the amount of gallons per hour that your sewage pump can move, there are a number of other important elements to consider when searching for a sewage pump. These include the quality of the pump’s construction and the size of its engine. Continue reading to discover more about these and other critical characteristics of a sewage pump.

Material

Sewage pumps spend the most of their life immersed in wastewater, therefore they must be extremely sturdy in order to last. In order to accommodate this, the majority of sewage pumps are constructed of cast iron or thermoplastic. However, while cast-iron pumps cost more than thermoplastic pumps, they are stronger and more robust and will therefore last longer than thermoplastic pumps, which are less expensive but will fail much sooner than an iron pump. Because of the solid waste that travels through it, the impeller, which is the portion of the pump that pushes the water, must be strong and long-lasting.

Other features of certain sewage pumps include the ability to quickly replace out individual components that are likely to wear out before the engine does.

Size and Weight

When purchasing a sewage pump, it is critical to evaluate the pump’s overall size in order to decide if it will fit correctly into a wastewater basin or septic pit. The majority of sewage pumps are around 16 inches tall and 11 inches broad. The weight of these models varies depending on how they are constructed. Premium pumps, which are constructed of heavy-duty cast iron housings, may weigh up to 45 pounds, whilst those that are constructed of cast iron and plastic can weigh as little as 20 pounds.

To handle solid waste up to 2 inches in diameter, residential sewage pumps must have an input and output of at least 2 inches in both directions.

Horsepower

The amount of sewage that a pump can handle on a daily basis is determined by its horsepower. Keeping this in mind, the larger the family, the more horsepower a sewage pump will require to keep up with the daily demands of the system. A sewage pump with 12 horsepower is sufficient for the majority of houses, but big households with more than four persons may require a sewage pump with 1 horsepower or higher. It’s vital to note that the lifespan of a sewage pump is directly proportional to the number of hours it operates.

This means that they will have a longer lifespan than a sewage pump that is less powerful and thus has to work more to meet the demands of a home.

As a result, while a less powerful sewage pump may be less expensive up front, it will not survive as long as a more powerful sewage pump, so offsetting the cost savings made initially.

GPH

The amount of wastewater that a sewage pump can transport in an hour is measured in gallons per hour (GPH). Some firms also use gallons per minute as a unit of measurement (GPM). The GPH or GPM of a sewage pump is determined by the horsepower of the pump as well as the elevation between the pump and the main sewage line or septic system to which the pump is pushing waste. Most sewage pumps may display their GPH in conjunction with an elevation, which is generally referred to as “head” measurement.

This indicates that if the height difference between the pump and the sewage line is 5 feet, the pump will be able to transport 4,000 gallons of water per minute.

The horsepower of a pump’s motor, as well as the design of the pump, affect how much GPH it can generate.

Features

The number of gallons per hour (GPH) that a sewage pump can move in an hour indicates how much wastewater it can transport. Gallons per minute is another term used by some manufacturers (GPM). The capacity of a sewage pump in terms of GPH or GPM is governed by the horsepower of the pump as well as the elevation difference between the pump and the main sewage line or septic system to which it is pumping waste. In most cases, sewage pumps will state its GPH in conjunction with an elevation, which is referred to as “head.” 5 feet of head = 4,000 GPH is an example of a pump’s flow rate.

The greater the elevation, the lower the GPH is expected to be.

It is similar to the case with horsepower: getting a less costly pump with a lower GPH will not save you money in the long run since it will have to work longer and will wear out more rapidly than a more powerful pump that does not have to work nearly as hard.

Our Top Picks

The models listed below include strong motors, long-lasting cast-iron construction, and high flow rates, which distinguish them as some of the best models available on the marketplace. Any of the pumps listed below would be suitable for use as a sewage-pump solution in a residence. Image courtesy of Amazon.com This model, from one of the industry’s most venerable brands, may be an investment, but its long-lasting construction and high-performance engine make it well worth it. The cast-iron structure of this pump instills trust in the user by providing a heavy-duty feel right out of the package.

At a height of 5 feet, a 12-horsepower engine can pump waste at a rate of 128 gallons per minute, and it can pump trash up to a maximum height of 21.5 feet if the situation calls for it.

According to the level of the water in the tank, the float switch automatically turns the pump on and off.

This type also incorporates an automated shutdown feature in the event that the pump becomes inoperative, so preventing harm. Approximately 11 inches long, 13.6 inches wide, and 16 inches high, the Zoeller 267-0001 measures in at 16 inches. Pros

Completely submersible due to its cast-iron structure. It has a maximum flow rate of 128 gallons per minute. Pump with non-clogging impeller designed for solid items Features such as automatic shut-off and a float switch

Image courtesy of Amazon.com This model from Liberty is one of the more powerful versions on the market, with to its solid cast-iron structure and strong motor, which pumps 160 gallons per minute to a height of 5 feet. Its 12-horsepower motor pumps to a height of 5 feet. Using a float switch, the pump is activated when the water level is between 12 and 16 inches above the bottom of the basin and turned off when the level drops below 6 inches from the bottom of the basin. The pump’s impeller and discharge can handle solids up to 2 inches in diameter, and its impeller and discharge are capable of handling larger solids.

Rust and corrosion are prevented from forming on the pump housing due to the powder coat finish applied to it.

Pros

Housing is made of heavy cast iron with a powder coat finish. 160 gallons per minute pumping capacity Solids up to 2 inches in diameter can be passed via a semi-open impeller. A maximum height of 25 feet is allowed.

Image courtesy of Amazon.com This sewage pump is a good choice because of its long-lasting structure and high production. This 12-horsepower pump can move a decent 4,800 gallons per hour at even height, and it has a maximum vertical height of 25 feet, which is outstanding for its size. And, while it may not have the same flow rate as higher-end pumps, the quality of build on this model makes it stand out from the crowd. A black coating protects the housing from rust and corrosion, and the housing is constructed of cast iron for long-lasting durability and reliability.

This pump, which can handle solids up to 2 inches in diameter, measures 9.75 inches in length, 16.75 inches in height, and 9 inches in width, which is about typical in size.

Cast-iron structure that is resistant to rust and corrosion

Impeller made of cast aluminum
It grinds bigger items. a tank that moves 4,800 gallons per hour A maximum height of 25 feet is allowed.

Our Verdict

TheZoellermodel is our top option for the finest sewage pump because of its cast-iron structure, submersible capabilities, and capacity to transport more than 128 gallons per minute, among other characteristics. Pumping water to a height of 21.5 feet and accepting tiny particles with its non-clogging impeller, this pump is simple to use and hassle-free to maintain. The Superior Pump, on the other hand, has the same cast-iron structure as the Superior Pump option, but it is significantly less expensive.

However, keep in mind that the 4,800 gallon per hour output means that less water is carried than with a typical pump.

How We Chose the Best Sewage Pumps

Sewage pumps are responsible for transporting wastewater (together with solids) from a residence to a septic system. In making our recommendations for the finest sewage pumps, we considered the materials used, the number of gallons per minute/hour transported, and any extra features that were incorporated to make operation more convenient. The above-mentioned choices are constructed of heavy-duty cast iron and aluminum for long-lasting sturdiness and submersibility. These alternatives also include durable impellers that can grind and transfer tiny debris and trash without blocking the pump’s intake or discharge valves.

Another advantage of the above possibilities is their capacity to reach heights of 21.5 to 25 feet while diverting 80 to 128 gallons per minute, depending on the configuration.

Furthermore, several of the above-mentioned choices have automated shut-off functions as well as float switches for increased efficiency.

FAQs

Learn how sewage pumps vary from effluent pumps, as well as how to determine what size sewage pump you require by continuing reading this article.

Q. What is the difference between an effluent pump and a sewage pump?

If the gray water has minimum particulates less than 12 inches in diameter, an effluent pump or sump pump can pump it out; on the other hand, a sewage pump can pump out black water that contains human waste up to 2 inches in diameter.

Q. What size sewage pump do I need?

A residential sewage pump must be capable of handling sediments up to 2 inches in diameter. In addition to that, most homes require a 12-horsepower sewage pump that can pump around 5,000 gallons per hour to the height of the main sewage line or septic tank, depending on the size of the home. It is possible that homes with sewage lines that are much higher than the sewage pump basin will require a more powerful pump to complete the task.

Q. How long do sewage pumps last?

A sewage pump will normally survive between 7 and 10 years, depending on how hard it is required to work and the quality of the materials used in its construction.

What do I do if My Septic Alarm is Going Off?

In the event that your septic alarm goes off, it may surely create some anxiety and uncertainty; and if you happen to be experiencing this right now, then you’ve arrived to the correct location! Don’t be concerned; it does not necessitate urgent action. Instead, take your time to go through this full essay so that you will be prepared to act now or in the future if the situation arises. What Septic Systems Are and How They Work The alarm works in conjunction with the septic system to alert you when the water level within the pump tank has increased to an unsafe level or has decreased to an unsafe level.

The timer is in charge of regulating the time intervals during which the pump is permitted to pump wastewater into the drainage system.

Thus, during periods of excessive water use, the drain field is kept from getting overflowing, which might cause damage to the drainage system.
A large amount of water is injected into the system in between pumping cycles for whatever cause, and the water has nowhere else to go but back into the system’s pump tank.
Depending on how much water was and continues to be put into the system and how the pump is set up to operate on a timer, it may take many pumping cycles until the water levels are returned to normal.

If you’ve ever had your septic alarm go off, you know how much stress and uncertainty it can create. If you’re now experiencing this, you’ve come to the perfect spot! Don’t be concerned
It does not necessitate urgent action. Instead, take your time to go through this full essay so that you will be prepared to act now or in the future if the situation warrants. What Septic Systems Are and How They Function In conjunction with the septic system, this alarm is designed to alert you when the water level within the pump tank has increased over a certain level or decreased below a certain level. All septic systems with pumps are required to have some type of timer installed. Using a timer, you may control how much wastewater the pump is permitted to pump into the drain field at different times of day. At certain periods of the day, these precise time intervals will occur. Thus, during periods of excessive water use, the drain field is prevented from getting flooded, which might cause damage to the drainage system. How Does a Problem Occur When There Is One? A large amount of water is brought into the system in between pumping cycles for whatever cause, and the water has nowhere else to go but back into the system’s storage tank. As a result, the water level within the pump tank will rise until the timer enables the pump to be turned back on. It may take many pumping cycles until the water level in the system returns to normal levels, depending on how much water was and continues to be injected into the system during the time intervals specified by the timer. Causes of the alarm going off that might occur

Somehow, groundwater is making its way into the system. If there is an excessive amount of standing water surrounding the septic tanks, whether generated by rain or another source, the water may seep into the tanks and cause the internal water level to rise.

It’s possible that one of the components of the septic system is malfunctioning. If anything goes wrong with your system — including the pump and floats — the alarm and timer will go off and the septic system will stop working correctly.

The Best Thing to Do If Your Alarm Goes Off Alternatively, if you hear an alert, you should press the red button or turn on the alarm box. The alarm will be turned off as a result of this action. There should be a red light and a green light on the alarm box, which should be situated someplace on the unit. The green light indicates that the alarm is operational and should be left on at all times. It is shown by a red light if the alarm is getting a signal from the pump tank indicating that the water level is increasing above or decreasing below what is expected.

If the breaker occurs to be tripped, look around the septic tanks to see if there is any standing water.

It is possible that the red light on the alarm box will go out on its own after allowing the septic system to operate for a couple of pump cycles (which should take approximately 10-15 hours).
If the red light turns off, it signifies that the system is operating properly and that it only needs to catch up with the extra water that has overflowed into the storage tank.
To be clear, an alarm signal from the septic system does not always imply that sewage is about to back up into the house right away.

Do you require septic system repair on a regular basis or emergency service?

To arrange an appointment, please call (804) 581-0001 or send us an email through our contact page. Want to learn more about septic systems? Explore our septic system web sites by clicking on the “Septic” navigation option in the top navigation bar.

Liberty Sewage Sewage Ejector Lift Pumps

Sewage ejector pumps are intended to handle raw sewage as well as solid waste products, according to the manufacturer. Pumps like this are often used to move raw sewage uphill, from a whole house or basement bathroom to a septic tank, aerobic treatment system, or gravity sewer main. Sewage pumps have a discharge of 2″ or 3″ and can handle spherical particles up to 2″ in diameter. Sewage ejector pumps are intended to handle raw sewage as well as solid waste products, according to the manufacturer.

Sewage pumps have a discharge of 2″ or 3″ and can handle spherical particles up to 2″ in diameter.

SEWAGE EJECTOR PUMPS

Submersible Sewage Ejector pumps are capable of handling raw sewage pumping duties. These pumps are meant to transport raw sewage wastewater from a lift station, which is often located in a basement or right outside the home, to a septic tank or aerobic treatment system, respectively. Our sewage ejector pumps can handle particles up to 2″ in diameter and have a discharge that is either 2″ or 3″ NPT. These pumps are designed for pumping operations requiring low pressure and large volume. Little Giant, Liberty, Ashland, and Myers are just a few of the sewage ejector pumps that we sell.

LITTLE GIANT

Little Giant is a branch of Franklin Electric, which is based in Chicago. The company Franlkin Electric has been acknowledged as the world’s top maker of submersible electric motors since 1944, when it first opened its doors. The Little Giant brand has been trusted by specialists in the water transfer sector for more than 70 years because of the reliability of its pump solutions, packaged system choices, accessories, and overall value. Little Giant is the brand of choice for hundreds of millions of people throughout the world because of its extensive line of sump, sewage, and effluent products.

LIBERTY PUMPS

Liberty Pumps, with its headquarters in Bergen, New York, is a prominent manufacturer of pumping devices for ground water and wastewater removal in residential and commercial applications in the United States. Our comprehensive choice of pump types includes sump pumps, sewage pumps, effluent pumps, drain pumps, grinder pumps, entire pre-assembled sewage packages, and pump accessories. We place a strong emphasis on creative product design in all of our products. Liberty’s products are relied on by hundreds of skilled contractors every day because they are distributed through a broad network of Plumbing Wholesalers and Pump Distributors.

ASHLAND PUMP

As a leading manufacturer and distributor of high-quality products for use in plumbing, onsite sewage, and the residential, commercial, industrial, and light municipal markets, the Ashland Pump Company has a diverse product range that is both durable and dependable.

A comprehensive line of sump, effluent, sewage, grinder, and non-clog pumps up to 20 horsepower is manufactured by Ashland Pump Company.

EJECTOR PUMPS OR GRINDER PUMPS. WHICH DO YOU CHOOSE?

Please keep in mind that grinder pumps should only be utilized in situations where they will be subjected to a minimum of 30 feet of head pressure. Without having to pump against at least this much back pressure, the motor will begin to spin at an excessively high rate of RPMs, causing it to overheat and eventually burn down very rapidly. Consequently, if you are not pumping into a common sewer main or have less than 30 feet of head, a sewage ejector, rather than a sewage grinder pump, is the better choice.

In the case of pumps connected to a pressurized sewer main

In the case of pumping over a large distance (greater than 1000 ft)
You have a long vertical distance to travel in order to remove the water (at least 30 feet)

The following are the situations in which a Sewage Ejector Pump will perform optimally:

When sewage is being pumped to a septic tank
When sewage is being pumped to a gravity sewer line
In the case of short distance sewage pumping (750 feet or less)
When lifting the water, you have a short vertical distance to overcome (less than 70 feet).

Summary: Sewage grinder pumps are not always required for the pumping of raw sewage, and not all sewage handling pumps are grinder pumps. In reality, in the vast majority of circumstances, a Sewage Ejector pump is the far superior choice. Furthermore, there are some situations in which you might utilize either kind.

Liberty Grinder Residential Sewage Grinder Pumps

Raw sewage and solid waste products are handled by sewage grinder pumps, which are specifically constructed for this purpose. Sewage grinder pumps are equipped with cutting blades that macerate particles prior to pumping them into the system. High pressure sewage pumps, such as those used in residential and commercial pumping applications and pumping to pressurized city sewer mains, are intended to handle long distances and high lifts, as well as pumping to high pressure sewage pump applications.

Raw sewage and solid waste products are handled by sewage grinder pumps, which are specifically constructed for this purpose.

High pressure sewage pumps, such as those used in residential and commercial pumping applications and pumping to pressurized city sewer mains, are intended to handle long distances and high lifts, as well as pumping to high pressure sewage pump applications.

SEWAGE GRINDER PUMPS

Sewage Grinder pumps, like Sewage Ejector pumps, are intended to handle raw sewage pumping duties. They are similar in design to Sewage Ejector pumps. Pumps for sewage grinders, on the other hand, are significantly more powerful. These pumps are capable of grinding sewage into a slurry and pumping it under extremely high pressure to its intended destination, among other things. There are a handful of applications in which these pumps are typically employed. In the first case, wastewater is pumped from a dwelling into a publicly accessible pressurized sewage main.

All of our grinder pumps have discharges that are 1-1/4″ NPT and have a starting horsepower of 2.0 HP.

Each model is available in two configurations: one with internal capacitors and another without internal capacitors (see below).

The internal capacitor versions are the most often encountered. These do not require the use of a control panel to function. In order to run the pump on the units that do not have internal capacitors, a separate control panel with built-in capacitors must be used.

GRINDER PUMPS OR EJECTOR PUMPS. WHICH DO YOU CHOOSE?

Please keep in mind that grinder pumps should only be utilized in situations where they will be subjected to a minimum of 30 feet of head pressure. Without having to pump against at least this much back pressure, the motor will begin to spin at an excessively high rate of RPMs, causing it to overheat and eventually burn down very rapidly. When pumping into a common sewage main or when you have less than 30 feet of head, you should use a Sewage Ejector pump rather than a Sewage Grinder pump, as explained above.

In the case of pumps connected to a pressurized sewer main
In the case of pumping over a large distance (greater than 1000 ft)
You have a long vertical distance to travel in order to remove the water (at least 30 feet)

The following are the situations in which a Sewage Ejector Pump will perform optimally:

When sewage is being pumped to a septic tank
When sewage is being pumped to a gravity sewer line
In the case of short distance sewage pumping (750 feet or less)
When lifting the water, you have a short vertical distance to overcome (less than 70 feet).

Liberty Pumps P372LE51 Pro370 Sewage Pump System Review

A sewage pump will be required if you need to remove sewage wastewater from a below-grade sewage system (i.e., one where a gravity drain line cannot be used) or pump it to a septic tank. A lot of homeowners, landlords, and small business owners try to save money at this stage by purchasing the lowest pump they can find and installing it as inexpensively as possible. Nevertheless, if you’re anything like us, you’d rather spend a little extra money and have the work done well the first time, since time is money, and peace of mind is priceless.

We’ve found the Liberty Pumps PRG101A to be the greatest sewage grinder pump we’ve discovered under $1,000, and it’s the most affordable.
In contrast, if you want an ejector pump that is boxed and ready to be installed as part of a home sewage package for a quick, uncomplicated, and dependable installation, you should look into the Liberty Pumps P372LE51 Sewage Pump System.
Does it perform as expected?
You can read our complete review of the book below, and you can purchase it here.
Included is the LE51A sewage ejector pump, which is powered by a 1/2 horsepower electric motor that has been throttled down to a maximum pumping rate of 8,400 gallons per hour and a maximum head of 24 feet.
It measures 30 inches in height, 20-1/4 inches in width at the base, and 24 1/2 inches across at its broadest point at its widest point.
The P372LE51 can pass spherical solids up to 2 inches in diameter and has heat protection built into the motor.

It is capable of handling liquids up to 140 degrees Fahrenheit, and it comes with an automated mechanical wide angle float switch.

At zero feet, the maximum pumping speed of the P372LE51 is lower than the maximum pumping speed of the LE51A alone; it peaks at 8,400 GPH at zero feet, then drops to 6,480 GPH at 10 feet, 2,640 GPH at 20 feet, and shuts down completely at 24 feet when the max head is reached.

This is accomplished by the use of a top inspection cover that has integrated rubber seals.

The system is delivered totally built, and it includes a transparent plastic overhead cover to keep it protected during the rough-in and masonry stages of the construction process.

This increased size of the basin, as compared to the more common 18 inch by 30 inch basin, can result in a decrease in pump and switch cycles of up to 40% and a longer life for both the pump and the switch.

Pumping rates are slower in the P372LE51 than in the LE51A owing to the way the pump is configured within the basin, but the maximum head stays the same in both.

The PRG101A is a superior sewage pump since it is a grinder pump rather than an ejector pump, which makes it more efficient.

As a grinder, it is capable of dealing with items that should not be flushed down toilets but are still flushed.

As an added bonus, the PRG101A has a significantly powerful engine (1 hp) and has a maximum pumping height that is more than twice as high as the PRG101, at 50 feet compared to 24 feet.

As a minimum, ensure that your dug hole has at least 8 inches of space around the tank; however, you’ll want to make it as tiny as feasible after that.

For back fill, you don’t want to utilize sand or native soil because of the contaminants.

It is important to ensure that your discharge pipe has at least the same diameter as your pump.

It is possible that a higher pipe size will be required to decrease losses due to friction.

It has to be at least as large as the discharge size in order to be effective.

On the subject of service life, the P372LE51’s design should provide you with significantly more years of service than you would get from the LE51A installed on its own; we estimate that up to 20 years of service will likely be possible, although the specific lifespan you’ll get on your model will naturally depend on a healthy dose of luck.

The bigger basin also has a longer life span since it reduces wear on both the pump and your switches.
There are several possibilities for why the pump is not running: a power problem (low voltage or blown fuse), an obstacle in the basin that is preventing the switch from being activated, not enough liquid in the pit to trigger the switch, or a broken switch (see below).
You’ll need to check for many things, including a clogged or blocked discharge, a check valve that’s reversed or closed, a ballvalve or gate valve that’s closed, too much lift for the pump to handle, a plugged volute casing or a jammed pump impeller.
After everything is said and done, if you’re looking for one of the most straightforward “plug and play” sewage ejector pump systems on the market, you’ll have a difficult time finding anything better than the P372LE51.
You may expect up to 20 years of trouble-free service if you install it in a household or business setting where people solely flush human waste down toilets.
In the end, the optimal response will be determined by your target audience, budget, and risk tolerance.
The Liberty Pumps LE51A can be purchased from this website.
The Zoeller M267 is available for purchase here.
You may get a quiet 2 inch check valve from this website.
In the event that you find our work at PumpThatSump to be useful, you may put our unrelenting testing of every pump and fixture available on the market to the test by shopping through our links above for everything you need to make your house a home.

Despite the fact that we are self-employed, we vow not to spend the entire amount for health insurance.

Differences Between Sewage Pumps and Grinder Pumps

Despite the fact that they seem identical, sewage and grinder pumps work in a completely distinct way to dispose of raw sewage. You may learn more about the differences between them by reading on. Do not hesitate to contact your local qualified plumber if you feel that your sewage ejector pump or septic grinder pump may be malfunctioning or have been damaged.

Sewage Ejector Pumps

Wategejector pumps are meant to pump raw sewage from your house into an onsite septic tank or gravity flow sewer main system for treatment and disposal. As a result, they are only capable of pumping to distances of less than 750 feet. A benefit of sewage ejector pumps, on the other hand, is that they are designed to transfer up to 200 gallons per minute of untreated raw sewage. This is a huge increase above the amount of waste that can be pumped by septic grinders. Generally speaking, sewage ejector pumps are designed to handle large quantities of sewage while operating at low pressures.

For example, unlike their grinder pump equivalents, sewage ejector pumps do not contain grinding blades to grind the sewage out of the system.

The sewage is subsequently forced into the discharge pipe with the use of pressure.

Septic Grinder Pumps

System with a high pressure and minimal volume, such as septic grinder pumps. They are therefore more suitable for transporting small quantities of raw sewage over greater distances than sewage injector pumps. If you require sewage to be transported to your pressured sewer main, a septic grinder pump will assist you in accomplishing this goal. The septic grinder pump is equipped with blades that are used to grind raw sewage into a slurry before it is released into the environment. It is then transferred to a pressurized sewer main where it is disposed of.

This implies that it will not be sent to the secondary system, which might result in the destruction of your subsurface leach field if it does.

Which Pump Should I Use?

When determining which sewage pump is appropriate for your home’s sewage pumping needs, it’s crucial to consider the amount of sewage you need to pump, the destination of the sewage, and the distance the sewage has to travel to reach its destination. In the event that you must pump sewage to a pressured sewer main, we propose that you install a grinder pump. Pumping to an aseptic tank or a gravity flow sewer main is far more efficient than pumping directly to the sewer main using a standard pump.

The trade-off is that grinder pumps are only capable of pumping small amounts of waste water.

The finest advice you can get when choosing a new sewage pump system for your house comes from a professional sewage pump plumber.

Our certified Rockford plumbers are available at (616) 901-1149 if you have any questions or concerns about our sewage or grinder pump services. Grand Valley Plumbing takes great satisfaction in assisting homeowners in maintaining the functionality of their plumbing systems.