How Do You Find Out Where To Dig Up Septic Tank?

a1environmental.net

• Most septic tanks are rectangular and will measure something in the neighborhood of 5’ x 8’. Use a metal probe to locate the edges and then mark off the perimeter. If you aren’t able to find the location of your septic tank using a probe, you’ll have to create a shallow excavation using a shovel along the perimeter to eventually locate the lid.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

How do I find a buried septic tank lid?

You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath.

How do I know if my house has a septic tank?

A surefire way to confirm whether or not your home has a septic system is to check your property records. It is likely that the building permit and blueprints for your home and property will contain information about the presence (or lack) of a septic tank.

How do you find a septic tank in an old house?

Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.

How deep is a septic tank in the ground?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.

Will metal detector find septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

Is septic tank better than sewer?

Although septic systems require a bit more maintenance and attention, they have a number of advantages over sewer lines. Since they don’t pump wastewater long distances to be processed at a water treatment facility, they use less energy overall and have a smaller environmental impact.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

What’s the difference between septic and sewer?

The main difference between a septic system and a sewer system is, a septic system treats your wastewater on site. Usually, it’s placed underground on the land your house is built on. Sewer systems take the wastewater away from your home and route it underground to a treatment plant typically operated by the city.

How to Find the Lid on a Septic System

All septic tanks eventually fill with sediments and must be pumped out on a regular basis in order to remain in excellent functioning order. If the tank’s lid is not on a riser at ground level and you are not the home’s original owner, you may be unable to determine where the lid is located. A typical septic tank is 4 inches to 4 feet underground, with all of its components, including the cover, buried between 4 inches and 4 feet underneath. This is true regardless of whether the septic tank is equipped with special risers that keep the lid flush with the surface of the ground.

Consult A Map

First, choose with the most straightforward choice. The installation of septic tanks at all locations is recorded in most counties’ permission records, which are kept on file for future reference. Typically, this will include a schematic indicating the placement of the tank on the land, as well as certain dimensions that will allow you to measure to the precise site of the tank. If your tank was placed before your county made it a requirement to record the location of such tanks, you may find yourself with nothing to show for your efforts.

Search For A Sign

Septic tanks are placed in such a way that they are as unnoticeable as possible on the land. After the grass has grown back after installation and some time has passed, it is possible that just a few visual indications will remain. Pay particular attention to the contours of your yard for any inexplicable high or low points that might suggest the presence of an underground storage tank.

Follow The Pipe

Installation of the septic tank takes place along the sewage line that runs from the house into the front yard. Locate the 4-inch sewage pipe at the point where it exits the home in the basement or crawl space, if it is there. Locate the same spot outside and make a note of it. Insert a thin metal probe into the earth, identify the 4-inch sewage line, and follow it across the yard, probing every 2 feet, until you reach the end of the property. Septic tanks are required to be at least 5 feet apart from the home in all states except Alaska.

Whenever the probe makes contact with flat concrete, fiberglass, or polyethylene it indicates that the tank has been located.

Locate The Lid

The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Investigate the tank’s circumference to determine its boundaries and outline the rectangle’s boundary using a pencil. A septic tank that was built before 1975 will have a single concrete lid that is 24 inches in diameter in the center of the rectangle. If the tank was built after 1975, it will have two covers made of fiberglass or polyethylene, centered at the ends of the rectangle and centered at the ends of the rectangle.

It should be possible to uncover the lid or lids by digging with a spade in specific spots, depending on when year the tank was constructed.

Call A Professional

Opening a septic tank is a job best left to the pros once the lid has been discovered. Concrete septic tank lids are extremely heavy, and many require the use of lifting tools to remove them completely. An open tank has the potential to release toxic gases. Anyone going around on the property who comes into contact with an exposed septic tank might be in risk. Because of the noxious vapors present in an open tank, falling into one can be lethal.

Mark The Spot

Septic tank lid opening is best left to the pros after you’ve discovered where it may be found. Several lifting tools are required to remove concrete septic tank lids, which are very heavy in some cases. An open tank may release toxic vapors into the atmosphere. Anyone roaming about on the property who comes into contact with an exposed septic tank might be seriously injured or perhaps killed. In addition to the noxious vapors, falling into an open tank can be lethal.

Dig (Excavate) to Locate Septic Tank or Drainfield

• POSTPONE a QUESTION or COMMENTabout digging to locate a septic tank, drainfield, D-box, or septic pipe, or about any other septic system components
• POSTPONE a QUESTION or COMMENTabout septic system components

InspectAPedia does not allow any form of conflict of interest. The sponsors, goods, and services described on this website are not affiliated with us in any way. The following are the times when it is necessary to dig to locate the septic system, tank or drainfield, soakaway beds or pipes, or D-box: We’d like not to have to dig up the entire yard in order to locate the septic tank or other septic components, wouldn’t you say? Septic system location videos are included with this article to demonstrate how to locate the leach field or drainfield component of a septic system, as well as situations in which digging or exploratory excavation is required and warranted.

(Septic drain fields are sometimes referred to as soil absorption systems or seepage beds in some circles.) For this topic, we also have anARTICLE INDEX available, or you may check the top or bottom of the page.

How to use Excavating to find Drainfield TrenchesTheir Condition

Part 7 of A Guide to Locating the Drainfield Based on the above-mentioned site observations, a homeowner could decide to drill a test hole in an area where he or she believes a leach line is located. The depth of a leach line may vary depending on the site circumstances, but it is typically 24″ or so. Alternatively, a septic contractor can just build a trench across the property, assuming that the soil cut will intersect the buried line. Digging over the whole property may be sensible only if we already know that the system has to be replaced, because the backhoe is likely to destroy any hidden piping it “discovers” when it is digging across the entire property.

Why we Like Digging by Hand First and Excavating by Backhoe Second

Equipment is preferred over shovels for digging on construction sites because it is faster, physically easier (using a machine is easier than wielding a shovel), and most importantly, it is more profitable.

Undoubtedly, in many situations, a backhoe is the only feasible option for digging. However, wherever feasible, we prefer to dig by hand before using a machine. When hunting for septic components, hand excavation causes the least amount of harm to a construction site because:

• Hand excavation causes the least amount of damage to the site, yard, plants, and other structures. Hand excavation can begin gradually, directly next to the building wall, without the need to wait for the arrival of heavy equipment
• Hand excavation can be completed by a motivated owner or her companions (but first read about SEPTICCESSPOOL SAFETY)
• Hand excavation helps to prevent harming steel septic tanks and covers (but first read about SEPTICCESSPOOL SAFETY)
• It also saves time. As a result, hand excavation (or a cautious backhoe operator) will not result in a freshly “explored” but now completely ruined septic system, which means you will not be able to utilize the building plumbing and will be compelled to accept whatever repair quote the contractor gives. (Trying to obtain septic repair cost estimates prior to any excavation is difficult since the contractor understands that there are too many unknowns – but insist on upper fair cost boundaries)

Where to Excavate to Look for Septic or Sewer Components

However, at some point, it becomes necessary to excavate, either because your hand digging proved futile or because you’ve discovered that substantial investigation and septic repair are likely required. An experienced excavation contractor usually has a very good sense of where another excavator would have excavated to locate a drainfield trench, D-box, or other septic system component, and can make educated guesses. Walking around the site and ruling in or out potential excavation sites can help to drastically minimize the amount of excavation required.

How to Think First and Dig Second – Narrowing the Search for the Drainfield

The day will come when you must excavate, either because your hand digging was ineffective or because you have discovered that substantial investigation and septic repair are likely to be necessary. It’s usually very easy for an experienced excavation contractor to make educated guesses about where another excavator would have excavated to install a drainfield trench, D-box, or any other septic system component. Taking a walk around the site and ruling in or out potential excavation sites will help to limit the amount of excavation required.

Septic Excavation Case Illustrated – step by step excavation to replace a sewer line

Our sewer line case study demonstrates in detail the stages involved in locating and digging septic components at a property. Detailed instructions on when, how, and why to repair the underground drain line that connects a house to a septic tank are included in this procedure.

Digging up a Failed Drainfield

Of course, if the leach field is already in need of repair, it is likely that the end of a leach line may be identified by observing where effluent is leaking to the surface of the ground.

Septic Drainfield Location Articles

• Clearance Disturbances, Septic System
• Odors, Septic or Sewer
• Locations of Septic Components
• Septic Drainfield Inspection Test at Home
• Septic Drainfield Location
• Septic Drainfield Inspection Test at Work

• LOCATION OF THE DRAINFIELD PIPE, EXACT
• EXCAVATE TO LOCATE THE DRAINFIELD
• REASONS FOR LOCATION OF THE DRAINFIELD
• Recordings to LOCATE the DRAINFIELD
• SURPRISING DRAINFIELD LOCATIONS
• UNLIKELY DRAINFIELD LOCATIONS
• VISUAL CLUES LOCATE the DRAINFIELD
• VISUAL CLUES LOCATE the SEPTIC TANK

• SERVING SEPTIC DRAINFIELDS
• SEPTIC DRAINFIELD SIZE
• SEPTIC DRAINFIELD Shape
• SEPTIC DRAWINGS
• SEPTIC DRAINFIELD RESTORERS

. Continue reading atREASONS to FIND THE DRAINFIELD, or choose a topic from the closely-related articles listed below, or see the completeARTICLE INDEX. Alternatively, read SEPTIC TANK, HOW TO FIND for further information on locating the septic tank, chamber, drywell, or seepage pit. LOCATION OF THE SEPTIC DRAINFIELD- HOUSE Inspection of septic drainfields at the residence Where to Look for the Septic Tank. Visit SEPTIC VIDEOS for more information on septic system location and maintenance.

Suggested citation for this web page

EXCAVATE in order to LOCATED DRAINFIELDatInspection An online encyclopedia of building environmental inspection, testing, diagnosis, repair, and issue preventive information is available at Apedia.com. Alternatively, have a look at this.

INDEX to RELATED ARTICLES:ARTICLE INDEX to SEPTIC SYSTEMS

Alternatives include asking a question or searching InspectApedia using the SEARCH BOXfound below.

Ask a Question or Search InspectApedia

We encourage you to use the search box just below, or if you prefer, you may make a question or remark in theCommentsbox below and we will get back to you as soon as possible. InspectApedia is a website that allows you to search for things. Please keep in mind that the publication of your remark below may be delayed if it contains an image, a web link, or text that seems to the program to be a web link. Your submission will appear when it has been reviewed by a moderator. We sincerely apologize for the inconvenience.

Technical ReviewersReferences

Citations can be shown or hidden by selecting Show or Hide Citations.

InspectApedia.com is a publisher that provides references. Daniel Friedman is an American journalist and author.

How to Locate Your Septic Tank

It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.

This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.

How To Find A Septic Tank: Step By Step

The fact that one of the largest and most visible elements of your whole plumbing system is simultaneously one of the most difficult to locate may seem impossible to believe, but when your property is served by a septic system, this is exactly true! There’s a solid reason for this: septic tanks are huge, unattractive, smell unpleasant, and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable area on your property and hides what would otherwise be a blight on your neighborhood.

You may identify your septic system using this blog, which eliminates the need for any time-consuming, labor-intensive digging.

1. Gather Some Helpful Tools

Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.

Using this method, you may also locate the cover for your septic tank.

While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.

2. Use a Septic Tank Map

If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation.

You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.

3. Start Ruling Areas Out

The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:

• Immediately adjacent to your well
• Beneath your home
• Directly against your home
• For example, underneath your driveway
• Under trees
• And other locations. Structures like a patio or deck are good examples of this.

4. Inspect Your Property

If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.

When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.

The likelihood of your septic tank being discovered in a few specific locations is quite high.

• Your water well, if you have one (for a variety of reasons that are rather clear)
• Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
• Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
• Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping

5. Inspect Your Yard

A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:

• If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
• Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.

The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.

6. Follow Your Sewer Main/Sewer Pipes

Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.

The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.

If the line is labeled, it is usually made of plastic or rubber. It is important to determine where this line exits your property and in which direction it is moving, as it often travels straight out to the septic tank itself.

7. Check Your Property Records

Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.

If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.

What to Do Once You Find Your Septic Tank

Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities. You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!

How to locate your septic tank and your drainfield

Septic systems on-site are used for accepting and treating wastewater in homes that are not linked to the municipal wastewater management system. A septic system is comprised of three components: a septic tank, a drain field, and piping. As a homeowner, it is your responsibility to properly operate and maintain your septic system in order to avoid system failure. For example, depending on the legislation in your area, you may be compelled to pump it on a regular basis. It is impossible to perform maintenance operations, however, if you do not know where the tank is located.

Steps to follow to locate your septic tank and drain field

The contractor that designed and constructed the septic tank on your property should have submitted an as-built diagram with the local health authority before starting work on the project. In the event that you have the contractor’s contact information, you can ask them for a schematic, which you can then use to pinpoint the location of your septic tank. If you do not have a copy of the schematic, you can request one from the local authorities. Depending on whether the installed system included electrical components, the schematic may be available at the regional building department offices.

When it comes to pinpointing the exact placement of your septic tank and drain field, this graphic may be quite helpful. If you are unable to locate the tank using this diagram, you will need to do more research on the land in order to determine its position.

The sewage outlet pipe is an excellent spot to start your physical evaluation of the property because it is accessible from the outside. This pipe is commonly found in the basement of a home, and it is a 4″ black pipe with a cleanout at the bottom. If the cleanout is behind a wall or in a closet, it is considered a hidden location. Simply look for possible access coverings or a structure that might be concealing it. Lift pumps are sometimes installed in basements to assist in pumping sewage from the building.

• Having discovered it, flush a toilet and listen to the pump to determine where the sewage is being discharged.
• You should now be able to see the general orientation of the septic tank and drain field from this point.
• The septic tank will be located a few meters away from the home, and the outflow pipe may be at an angle of 30 or 45 degrees from the house.
• Work your way around the home in a circle, starting at an electrical outlet and continuing until you find the septic tank.

Tips for locating your septic tank

Septic tank lids should be visible from the outside. An underground riser may have been added, which will make it simple to find your septic tank in some instances. However, it is conceivable that the septic tank cover is buried underground, which is especially true for older homes. Following are some pointers to assist you in locating the septic tank in this and other similar situations.

• It may be possible to discover the septic tank lid underneath using a metal detector if it is buried. Prevent wearing footwear that contains steel or any other metal in order to avoid interfering with the readings of the detector
• Instead, you can use a flushable transmitter that is flushed down the toilet and then tracked with a receiver. When it comes to septic tanks, the strongest signal will be seen close to the intake region of the tank.

Depending on whether the septic tank is above or below ground, you may have to dig to get to it. Construction materials for septic tanks include concrete, fiberglass, or plastic, and their shapes can range from oblong to cylindrical to rectangular. The majority of modern septic tanks will have their lids positioned in the center of the tank, and the lid should be within three feet of the ground surface in most cases. However, depending on a variety of conditions, such as farming and other human activities on the property, it is conceivable that it will be significantly deeper.

Additionally, you may use a small steel rod to probe the earth in order to pinpoint exactly where the tank is located as you continue digging.

Inspecting the tank

It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been identified. First and foremost, you may unscrew the lid to inspect the scum and sludge layer beneath it. In addition, the use of tracer dye tablets allows you to check the septic tank without having to dig it up. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of two days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field has a glowing green hue surrounding it.

It is possible that someone will fall into the tank, causing significant damage or possibly death. Additionally, all septic tank maintenance techniques should be carried out in accordance with the legislation governing the sewage system.

Conclusion

You can identify your septic tank without assistance from a professional, but it is a good idea to have someone who is properly educated in septic tank maintenance examine and maintain your septic tank on your behalf. The effluent filter in your tank should be washed into the open septic tank rather than on the ground in your yard if your tank has one. It may also be a good idea to make a note of the position of the septic tank when it has been discovered. This will be beneficial to anyone else who may require access to the septic tank in the future.

Septic tanks release combustible and hazardous gases, and as a result, they must be located in an open area.

How to Locate a Septic Tank

You can identify your septic tank without assistance from a professional, but it is a good idea to have someone who is properly educated in septic tank maintenance examine and maintain your septic tank on an ongoing basis for you. If your tank is equipped with an effluent filter, it should be rinsed into the open septic tank rather than on the ground in your yard. In addition, it may be beneficial to make a note of the position of the septic tank after it has been discovered. The information provided here will be useful to anybody else who may require access to the septic tank in the future.

The presence of septic tanks in the open is required due to the release of combustible and hazardous gases.

1.Follow the Outgoing Sewer Pipe

Look for the four-inch sewage pipe that runs through the structure and the location where it exits the building in the basement or crawl space. Locate the location outside the building where the pipe exits the building or the location of an access cover over the pipe. It is required that septic tanks be at least five feet away from the structure, although they are usually between 10 and 25 feet away. You may follow the pipe all the way to the tank using a metal probe. It is important to note that sewage lines may curve and run around the corner of a building rather than following a straight path to the holding tank.

2.Search for Septic Tank Risers and Lids

Depending on their age, septic tanks are either one- or two-compartment structures. Each compartment has a cover, with two additional lids for dual-compartment tanks that were added later. If the tank includes an access point known as a riser, the lid may be readily visible from outside. Look for round, plastic discs that are about a foot or two in diameter.

Due to the fact that the lids might be flush with the ground or just a few inches above it, they can get overrun with grass and other plants over time. You can also come upon a large concrete lid. Tanks without risers are likewise equipped with lids, however they are located underground.

3.Find the Drain Field First

In the absence of a riser and lid, search for indicators of a drain field, such as an area of grass that grows more quickly or more slowly than the rest of the yard, grass that is a different color from the rest of the yard, or areas where snow melts more quickly than in other parts of the yard. Spots of high or low ground in the yard might possibly indicate the presence of a subterranean tank or drain field. You will be able to discover the tank if you probe these regions.

Reasons to Hire a Contractor for Help

Attempting to locate a septic tank on your own can be risky, and in some cases, lethal, if the septic system is old and in danger of collapse. In the event that you fall into a cesspool, dry well, or septic tank, you will die. Removing septic tank lids on your own might potentially put you at risk of contracting bacterial or virus diseases. If you detect any of the following issues, please contact a contractor to assist you in locating or inspecting your septic tank:

• Soil that is sinking around the tank or drain field. Drainage backup into the home’s sewer system, or toilet backup
• A foul odor in the area where you assume the tank and drain field are located
• When there is no rain, pooling water, muddy soil, or spongy grass might occur. Septic tank covers that are rusted, cracked, or have been replaced with improvised lids are prohibited.

Even though you may be ashamed about forgetting where your septic tank is, it is a very frequent problem among homeowners. A contractor may assist you in locating it, and he or she may do it as part of the pumping service. If you need assistance locating your tank or if you have any other questions, please contact us at 503-630-7802. We are available to assist you!

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

If you’re like most people, you like relaxing on your back patio or porch and taking in the scenery rather than worrying about where your septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repairs. Learn more about how to locate your septic tank by continuing reading this article. 1.

Inspect Your Property

Imperfections in the terrain might sometimes provide clues as to where your septic tank is located. Septic tanks are often placed in such a way that you can scarcely know they are there. However, dips in the soil or tiny hills in the landscape may suggest the presence of a septic tank hidden beneath the ground. You may use your soil probe to find your septic tank if these dips or hills are located between five and twenty-five feet distant from your property line. Because most septic tanks are located between six inches and four feet underground, make sure you probe the soil to a sufficient depth before installing the tank.

While you are inspecting your property, keep a look out for the septic lid that may be missing.

With the help of your metal soil probe, you should be able to locate the septic tank lid. These are often found at or slightly below ground level, depending on the situation. It is unlikely that your septic tank will be located beneath any of the following:

• Paved surfaces
• Unique landscaping
• Your water well, if you have one
• And other features.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.

Most counties, on the other hand, keep records of septic tank installations for every address.

Don’t Try to Fix Septic Tank Issues Yourself

Having trouble getting this? We can help. Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can use. – Perhaps you will be shocked to learn that there are several ways to obtain information on your property without ever leaving the comfort of your own residence. Structure permits, for example, are frequently found in county records, and they may include schematics with specifications on how far away from a septic tank a building should be, as well as other valuable information such as the size of the tank.

Yet the majority of counties continue to keep track of septic tank installations at all locations.

Schedule Septic Tank Maintenance

The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.

Metropolitan Atlanta and the neighboring areas receive high-quality service from us. We are open seven days a week, twenty-four hours a day. When you require emergency sewer services, we are here to assist you.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.

If you’re also using well water, it’s possible that you won’t receive one at all.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis.

All of the heavy lifting has been delegated to our team of professionals.

Dig the Correct Cover

Here are a few pointers to assist you in locating and digging the proper cover for your septic tank:

• Locate the 4′′ sewage pipe that runs from your toilet and shower to the exterior wall of your home. It should be visible. Most of the time, your tank is 8 to 15 feet from the place where the sewer pipe exits
• Perhaps you have seen an area outdoors where snow melts each winter
• Most of the time, this location is within the 8 to 15-foot range. This is an excellent place to begin. To identify the four corners of the tank, probe the ground with an abar and mark the locations. A septic tank measures roughly 8 feet long by 5 feet broad and is covered with three different types of coverings. Some tanks, on the other hand, are longer and made of plastic, making them more difficult to spot. Our company, Maine SepticPumping, requests that you find and excavate the center cover in order for us to thoroughly clean and remove any sediments from your tank. If you have a septic system that includes a pump, you should exercise caution. Unground electrical wire will be present, and it is possible that it could pose a hazard. You should also find and dig the cover for your pump chamber so that it can be pumped at the time of our service
• If you are experiencing sluggish drains and the digging is relatively simple, you can try excavating all of the tank covers. All of the covers being removed would allow us to inspect your input region and eliminate any sediments that may be blocking the passage of the water. This also allows us to view your outlet baffle clearly, allowing us to ensure that it is secure. If you have any questions when trying to locate your tank, please contact our office. MaineSepticPumping can also assist you in locating and digging your cover.

How to Find Your Septic Tank Lid

Previous PostNext PostWhether you realize it or not, it is critical that you be aware of the position of your septic tank lid and the septic tank itself.

Despite the fact that septic tanks are fairly huge, they can be difficult to identify, particularly if they have not been properly maintained over time. Continue reading to find out how to locate your septic tank lid.

Why It’s Good to Know Where to Find Your Septic Tank Lid

Knowing the location of your septic tank is a fantastic approach to spot septic tank problems as soon as they occur. Consider the following scenario: If you saw water near your septic tank lid, you would know right away that you could have a problem with your system being overloaded with waste. Furthermore, by understanding where your septic tank is located, you may avoid parking cars on top of it, which might cause the tank to collapse and create flooding. You’ll also be able to point service personnel in the right direction for septic tank services, which will eventually save them time and money while also saving you money.

How to Find Your Septic Tank Opening

Knowing how critical it is to know where your septic tank lid is located, it’s time to go out and find one for yourself. Keep an eye out for a circular lid that is roughly two feet in diameter during your quest. Septic tank lids are normally constructed of green or black plastic, however they can occasionally be made of concrete. It is not always simple to locate the septic tank lid, however, because untidy vegetation, mud, or debris might obscure the lid’s location. If you live in a snowy climate, seek for a spot of lawn where the snow melts more quickly than it does anywhere else on the property.

How to Find Your Septic Tank Lid as a New Homeowner

During the process of purchasing your house, you should have been provided with a map of your property that showed the location of your septic tank. This is normally included as a part of your home inspection service package. All you have to do from there is compare the diagram to your land, find the septic tank location, and potentially dig around it to check whether the lid has been hidden by vegetation or other obstructions. People have been known to place an object such as a huge rock on top of the septic lid, so be sure to look beneath landscaping stones as well.

How to Find Your Septic Tank Lid as an Existing Homeowner

Still having trouble locating your septic tank lid? There’s a significant probability it’ll end up in the ground. The pipes coming from your basement should be followed, as they will take you in the direction of your septic system, which is what we propose. Then, once you’ve determined the correct direction, check for any high or low points in the yard that might reveal the location of your septic tank. You can find the lid of your septic tank by probing the ground with a metal probe every few feet with the probe.

Because most lids have a metal handle or fastener on them to hold the lid closed, you may also use a metal detector to find them.

The majority of lids are buried up to a foot deep, but some lids might be buried as deep as four feet in extreme cases! In some instances, a professional with specialized locating equipment may be required.

How to Maintain Your Septic Tank Lid

Following the discovery of your septic tank lid, keep it in good condition to avoid damage and ensure simple access for future septic tank maintenance, such as pumping your septic tank every three- to five-year period. Here are some pointers for keeping your septic tank lid in good working order:

• Keeping the grass around the septic tank lid regularly mowed is important. Remove any dirt or debris that may have accumulated on your septic tank lid
• Mark the area to ensure that no one parks or constructs structures there. It is possible to do this using a flag, garden décor, or ornamental pebbles.

Professional Septic Tank Services

Is it difficult to find trustworthy septic tank services or septic tank installation? If you are looking for septic tank installation, inspection, and cleaning services, check with your local Mr. Rooter ® Plumbing franchise. Mr. Rooter charges a set amount up front, with no overtime fees or additional expenses. To get started, call us at (855) 982-2028 or fill out our online estimate request form. Is the lid of your septic tank obscured by grass? Inquire with The Grounds Guys about routine lawn care and upkeep.

Rooter, is a member of Neighborly’s network of dependable home service experts, which includes Mr.

By hiring The Grounds Guys to provide trustworthy grass mowing and landscape care services, you can be assured that your septic tank lid will always be simple to locate.

How To Find My Septic Tank

1. Is it difficult to find trustworthy septic tank maintenance or septic tank installation? For more information about septic tank installation, inspection, and cleaning, check with your local Mr. Rooter ®Plumbing location. With Mr. Rooter, you will never be surprised by an unexpected bill for overtime. To get started, call (855) 982-2028 or submit a request for an estimate online. Grass has grown up around the top of your septic tank lid. For more information on basic lawn maintenance, contact The Grounds Guys now. Neighborly’s network of trustworthy home service providers includes companies such as Mr. Rooter and The Grounds Guys. With trustworthy grass mowing and landscape care services from The Grounds Guys, you can be assured that your septic tank lid will always be simple to locate. The preceding and next posts

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

1. “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
2. When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
3. The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
4. In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

1. A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
2. A septic system is likely to be installed in your home if you reside in a rather rural location.
3. Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
4. When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
5. Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

What is the best way to determine whether or not your home has a septic system? The majority of the time, there are a few indicators. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage network. It is probable that the utility company will not charge you for wastewater or sewage services if you are utilizing a septic system to handle your wastewater management. Of course, if you have a septic system, there is a chance that you will not get a water bill at all!

• There is a good chance that you are utilizing well water rather than public utility water if the water pipe leading into your home does not have a meter attached to it.
• You are more likely to have a septic system in your home if you reside in a more rural setting.
• The likelihood is that your home is also equipped with a septic system if all of your neighbors are.
• It is common to find a mound or tiny hill on the property where a septic tank is installed that is not a natural structure.

Checking your property records is a foolproof method of determining whether or not your home has a septic system. It is quite probable that the construction permit and plans for your home and land will include information concerning the existence (or absence) of a septic tank on the site.

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

• If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
• The county health department is responsible for keeping track of septic systems.
• A septic tank’s position could be depicted on a survey map, for example.
• The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

In this way, if you ever decide to sell your property, you will be able to supply the new owner with everything they will need to locate the tank and properly manage their septic system.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

1. In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
2. By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
3. The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
4. Going via the sewage line itself is another method of locating the septic tank utilizing it.
5. Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
6. When the snake comes to a complete halt, it has almost certainly reached the tank.
7. While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
8. When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation.

However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

• Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
• Directly in front of the home Immediately adjacent to your well (if you have one)
• In close proximity to trees or densely planted regions
• In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job