What Do You Use To Probe Around A Septic Tank? (Solution found)

  • Simply use a measuring tape to measure out the dimensions to find the septic tank lid. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid. You can locate the lid of your septic tank by poking the ground every few feet with a metal probe.

How do you probe a septic line?

Follow the pipe by sticking a thin metal probe (known as a soil probe) into the ground near the sewer line. Probe about every two feet. Most septic tanks are around 10-25 feet away from your home, and cannot be closer than five feet.

Will a metal detector locate a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

What is a septic tank probe?

This soil probe is an easy to use job site tool for underground pipe detection. The probe simply drives into the ground to locate the pipe before digging. You can save time and money by digging unobstructed.

How do I find my septic laterals?

Call your local electric utility provider or gas company to locate buried gas or utility lines before digging. A septic tank probe can also help you find the location. Stick the long, thin metal probe into the ground until you feel it hit the tank and feel the edges of the tank.

How far apart are septic tank lids?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

Where are most septic tanks located?

Toe the Line. Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.

How do you put in a Drainfield probe?

Scan the area for markers: The location of your septic tank should be marked by a cement marker the size of a manhole cover. Look for it 10 to 20 feet away from your home. Once you locate the tank, follow the downward-most path and check for an empty downward-sloping field. You may have just found your drain field.

How do you ground a probe?

Using the soil probe is easy. Simply insert the pointed end into the soil and push as deep as you can, then slowly pull up.

Should septic tank lids be buried?

In most cases, all components of the septic tank including the lid are buried between 4 inches and 4 feet underground. Unless the septic tank has special risers that position the lid at ground level, you’ll have to dig for it.

How do you tell if your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

  1. Your Drains Are Taking Forever.
  2. Standing Water Over Your Septic Tank.
  3. Bad Smells Coming From Your Yard.
  4. You Hear Gurgling Water.
  5. You Have A Sewage Backup.
  6. How often should you empty your septic tank?

How many lids are on a septic tank?

In order to make repairs or perform regular maintenance or cleaning/pumping of the tank, access must be provided. There are usually two lids located at the top of the septic tank-one located over the inlet “T” and one located over the outlet “T” (see “Septic Components: Septic Tanks”).

How to Use Special Equipment to Find The Septic Tank or Septic Waste Lines

  • To guarantee that your tank does not fail, you should examine it on a regular basis and get it pumped out as prescribed by the provincial codes. Septic tanks will begin to leak if they fail, and these leaks will contaminate the environment as they continue to degrade. A septic system that has failed to the point of damaging the environment will be required to be replaced by the legislation, which is quite harsh. In order to prevent this from happening, it is in your best advantage to learn about the suggested pumping schedule for your vehicle. Provincial legislative regulations, as stated above, set the timetable for the events.

To guarantee that your tank does not fail, you should examine it on a regular basis and get it pumped as prescribed by the provincial rules. If a septic tank fails, it will begin to leak, and any leaks will pollute the surrounding area. A septic system that has failed to the extent of damaging the environment will be required to be replaced by the legislation, which is particularly stringent in this case. As a result, it is in your best interest to ensure that you are aware of the suggested pumping schedule.

ToolsEquipmentto Find theSeptic Tank

The following section discusses sewage tank finding tools and equipment. If you have not already done so, please read our more basic method to locating your septic tank by visual inspection: SEPTIC TANK, HOW TO FIND. Remember to use caution while probing or excavating a septic tank, drywell, or cesspool, especially if you are not convinced that the installation has a safe and secure cover. Probing or excavating over a failing septic tank or cesspool, or even drywall, can cause the system to collapse, which is potentially lethal.

  • Some inspectors or septic service companies use a simple septic tank locating probesuch such as a 1/4″ steel rod or a heavier steel wrecking bar to probe the ground over a suspected septic tank location. Caution: jamming a heavy wrecking bar into the soil can perforate a steel septic tank cover or break a terra cotta septic tank cover. However, these methods can be useful if used carefully in soft or wet soils (in a related application, the examination of septic fields, we’ve used a wrecking bar to make holes in a drainfieldnot directly over a drain line in order to look at soil conditions. A failing septic system may send effluent right up to the surface through such an opening. The use of a shovel to locate any buried object is a low-tech and high-sweat method of locating any buried object if you have a general idea of where to look. When we first searched for our septic tank in 1969, our contractor used a backhoe to “find” the septic tank. He “found” it, to be sure, by driving over and collapsing an old steel septic tank. I wished we had started more gently Using a metal detector, you may locate certain septic tanks that have steel tank tops or manhole covers that have been utilized to cover the entry port to the tank. A special plumbing snake fed into the main house drain line and extended until it hits an obstruction, which may be an obstruction in the drain line or it may be that the snake has extended into and harmed the septic tank: Some plumbing contractors can at this point find the exact location of the septic tank by using an electronic drain pipe sensor. To locate the septic tank, ground scanning radar is used. Ground scanning radar can identify buried septic tanks, buried oil tanks, and other items beneath the earth. Companies that provide buried oil tank locating services are frequently able to provide this (more expensive) service.

Warning about using metal detectors or electronic pipe sensors to find Septic Tanks

Metal detectors or probes that indicate the course of an underground pipe are great and quick methods of locating buried drain and septic system components, as well as other buried infrastructure. However, on an older property, we’ve had an odd problem that may have been quite disastrous. If your property is old, it may contain numerous generations of underground cables and pipes, which can cause errors in the readings from sensors such as those for buried pipe or buried septic tank monitoring.

After attaching a transmitting unit to a pipe at the gas meter, the technician proceeded to paint a yellow line over our (at the time frozen) earth with a paintbrush.

We started digging 18 inches deep using a jackhammer to break through frozen earth in order to locate a water pipe “a safe distance away from the yellow line indicating the gas line As one might expect, we came across the gas line itself while we were excavating!

Keep an eye out for: Excavation equipment such as backhoes, wrecking bars, and jackhammers should not be used in areas where potentially dangerous utilities are underground.

SEPTIC LOCATION VIDEOS includes videos that demonstrate how to locate a septic system, septic tank, and septic drainfield, among other things.

Reader CommentsQ A

Please accept my apologies, but I am not familiar with the term “dry tank.” I know where the septic tank is, but I can’t seem to locate the dry tank. My home was constructed in the 1960s. I’m trying to locate the health department because I want to put up a vehicle awning for my camper. In order to determine the *exact* position of the entrance and exit of a septic tank, you must first locate the tank. 2. Remove the cover from the risers or cleanout apertures depending on the tank type and size, there may be two, three, or more of these openings.

  • I normally take measurements from the building’s nearest corners and develop a diagram for future reference.
  • Those measuring methodologies are described in greater depth in the preceding article.
  • It is reasonable to assume that the septic hookup would be near to the edge of the actual RV rectangle if the location where the RV was parked can be identified and identified.
  • A plumber can install a buried drain tracing wire at the septic tank and use an above-ground detector to trace the course of the plumbing.
  • There were two RVs here a few years ago, but no hookups can be discovered now.
  • The ground is quite difficult!
  • How can I locate the septic tank if a septic line runs down into a cement pad and is not visible?
  • Alternatively, choose a topic from the closely related articles listed below, or browse the entireARTICLE INDEX.

Recommended Articles

  • HOW TO FIND THE LOCATION AND SIZE OF THE SEPTIC TANK COVERS
  • HOW TO FIND THE LOCATION AND SIZE OF THE SEPTIC TANK
  • SEPTIC D-BOX INSTALLATION, LOCATE, AND REPAIR. HOW TO FIND THE LOCATION AND SIZE OF THE SEPTIC TANK COVERS.
  • THE DISTANCE TO THE SEPTIC TANK
  • FIND THE MAIN WASTE LINE EXIT
  • POSSIBLE SEPTIC TANK LOCATIONS
  • SEPTIC TANK COVERS
  • SEPTIC TANK DEPTH
  • SEPTIC TANK DESIGN DEPTH
  • SEPTIC TANK LOCATING EQUIPMENT
  • SEPTIC TANK LOCATION SKETCH
  • SEPTIC TANK RISERS
  • SEPTIC TAN

Suggested citation for this web page

AT INSPECT A PEDIDO.COM- an online encyclopedia of building and environmental inspection, testing, diagnosis, repair, issue avoidance advice- you will find all you need to know about locating septic tanks. Alternatively, have a look at this.

INDEX to RELATED ARTICLES:ARTICLE INDEX to SEPTIC SYSTEMS

Alternatives include asking a question or searching InspectApedia using the SEARCH BOXfound below.

Ask a Question or Search InspectApedia

We encourage you to use the search box just below, or if you prefer, you may make a question or remark in theCommentsbox below and we will get back to you as soon as possible. InspectApedia is a website that allows you to search for things.

Please keep in mind that the publication of your remark below may be delayed if it contains an image, a web link, or text that seems to the program to be a web link. Your submission will appear when it has been reviewed by a moderator. We sincerely apologize for the inconvenience.

Technical ReviewersReferences

Please use the search box just below, or, if you prefer, you may make a question or remark in theCommentsbox below and we will react as soon as we can. Thanks for visiting! InspectApedia is a website that allows you to search for information. Please keep in mind that the publication of your Comment below may be delayed if it contains an image, a web link, or text that seems to the program to be a web link. Your posting will appear when it has been reviewed by a moderator. Excuse the delay in getting back to you!

Septic Locating – All American Septic

If the septic tank is covered, it is necessary to locate it. Our skilled specialists can find for an extra cost using an As-Built and a water probe, which they will provide to you. The As-built provides us with a general place from which to begin investigating. With the water probe, we are able to enter the earth and discover the position of the septic tank without having to dig up your lawn or harm your landscaping. Lids on septic tanks may be located electronically – It may be essential to find the Septic Tank lids electronically in some situations.

See also:  How Much Time Between Septic Tank Pumping? (Solved)

The use of an electronic locator should only be done as a last option.

It will aid you in finding the general placement of the Septic Tank itself if you have an As-Built.

1 Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby.

Depending on the quality of your septic system, the grass in the vicinity of the tank may be greener and more vigorously growing than elsewhere.

If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.

County health departments are frequently in charge of keeping track of septic systems. If your municipality or county does not have a property survey map accessible, you might inquire if such a map is available. A septic tank’s position could be depicted on a survey map, for example.

2 Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. Notify yourself of where your pipe exits the home, and then proceed outside to locate the matching place in your yard.

Every two feet, take a probe and see what you find.

The tank will be located after the probe detects the impact of flat concrete, fiberglass, or polyethylene against the surface.

What to Do After You Find Your Septic Tank?

All septic tanks eventually fill with sediments and must be pumped out on a regular basis in order to remain in excellent functioning order. If the tank’s lid is not on a riser at ground level and you are not the home’s original owner, you may be unable to determine where the lid is located. A typical septic tank is 4 inches to 4 feet underground, with all of its components, including the cover, buried between 4 inches and 4 feet underneath. This is true regardless of whether the septic tank is equipped with special risers that keep the lid flush with the surface of the ground.

Consult A Map

First, choose with the most straightforward choice. The installation of septic tanks at all locations is recorded in most counties’ permission records, which are kept on file for future reference. Typically, this will include a schematic indicating the placement of the tank on the land, as well as certain dimensions that will allow you to measure to the precise site of the tank. If your tank was placed before your county made it a requirement to record the location of such tanks, you may find yourself with nothing to show for your efforts.

Search For A Sign

Septic tanks are placed in such a way that they are as unnoticeable as possible on the land. After the grass has grown back after installation and some time has passed, it is possible that just a few visual indications will remain. Pay particular attention to the contours of your yard for any inexplicable high or low points that might suggest the presence of an underground storage tank.

Follow The Pipe

Installation of the septic tank takes place along the sewage line that runs from the house into the front yard. Locate the 4-inch sewage pipe at the point where it exits the home in the basement or crawl space, if it is there. Locate the same spot outside and make a note of it. Insert a thin metal probe into the earth, identify the 4-inch sewage line, and follow it across the yard, probing every 2 feet, until you reach the end of the property.

Septic tanks are required to be at least 5 feet apart from the home in all states except Alaska. The majority of them are between 10 and 25 feet distant. Whenever the probe makes contact with flat concrete, fiberglass, or polyethylene it indicates that the tank has been located.

Locate The Lid

The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Investigate the tank’s circumference to determine its boundaries and outline the rectangle’s boundary using a pencil. A septic tank that was built before 1975 will have a single concrete lid that is 24 inches in diameter in the center of the rectangle. If the tank was built after 1975, it will have two covers made of fiberglass or polyethylene, centered at the ends of the rectangle and centered at the ends of the rectangle.

Call A Professional

Opening a septic tank is a job best left to the pros once the lid has been discovered. Concrete septic tank lids are extremely heavy, and many require the use of lifting tools to remove them completely. An open tank has the potential to release toxic gases. Anyone going around on the property who comes into contact with an exposed septic tank might be in risk. Because of the noxious vapors present in an open tank, falling into one can be lethal.

Mark The Spot

Make a note on the ground near where the tank was pumped by a professional and the lid was buried to serve as a reference in the future. In order to keep track of where you are, you should choose a hefty circular patio tile that is embedded in the ground. Additionally, draw your own map of the area and store it with your other important papers.

How to Locate Your Septic Tank

It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.

This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.

How To Find A Septic Tank: Step By Step

It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.

The Plumbing Experts have put out all you need to know about locating the septic tank on your property in this blog post for your convenience.

1. Gather Some Helpful Tools

Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.

Using this method, you may also locate the cover for your septic tank.

While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.

2. Use a Septic Tank Map

If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.

3. Start Ruling Areas Out

The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:

  • Immediately adjacent to your well
  • Beneath your home
  • Directly against your home
  • For example, underneath your driveway
  • Under trees
  • And other locations. Structures like a patio or deck are good examples of this.

4. Inspect Your Property

If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.

When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.

The likelihood of your septic tank being discovered in a few specific locations is quite high.

  • Your water well, if you have one (for a variety of reasons that are rather clear)
  • Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
  • Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
  • Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping

5. Inspect Your Yard

A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:

  • If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
  • Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.

The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not.

As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.

6. Follow Your Sewer Main/Sewer Pipes

Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.

The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.

If the line is labeled, it is usually made of plastic or rubber.

7. Check Your Property Records

Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.

See also:  How Do You Fond A Septic Tank? (Solution found)

If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.

What to Do Once You Find Your Septic Tank

Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities. You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be.

When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.

Inspect Your Property

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.

  • Paved surfaces
  • Unique landscaping
  • Your water well, if you have one
  • And other features.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

It is also possible to question your neighbors about the location of their septic system on their property if you are still having trouble locating yours. Finding out how far away their septic systems are will help you figure out where yours may be hidden in your yard or garden.

Don’t Try to Fix Septic Tank Issues Yourself

Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems.

Falling into an open sewage tank can lead to injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.

Schedule Septic Tank Maintenance

The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.

We are open seven days a week, twenty-four hours a day.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.

If you’re also using well water, it’s possible that you won’t receive one at all.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not blow away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis. Preventing worse problems and the need for costly repairs down the line may be accomplished via proper septic system maintenance. All of the heavy lifting has been delegated to our team of professionals.

How To Find My Septic Tank

  1. What is a septic tank
  2. How do I know if I have a septic tank
  3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
  4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

  1. “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
  2. When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
  3. The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
  4. In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

  • A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
  • A septic system is likely to be installed in your home if you reside in a rather rural location.
  • Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
  • When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
  • Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

See also:  How To Unclog A Slow Bathtub Drain With A Septic Tank? (Best solution)

4. Ease of Getting It Fixed

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being used all at once.

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

  • If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
  • The county health department is responsible for keeping track of septic systems.
  • A septic tank’s position could be depicted on a survey map, for example.
  • The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

  1. In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
  2. By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
  3. The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
  4. Going via the sewage line itself is another method of locating the septic tank utilizing it.
  5. Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
  6. When the snake comes to a complete halt, it has almost certainly reached the tank.
  7. While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
  8. When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

  • Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
  • Directly in front of the home Immediately adjacent to your well (if you have one)
  • In close proximity to trees or densely planted regions
  • In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

It is only the beginning of the effort to locate your septic tank. Following the discovery of the tank, the following step is to locate the lid. Your soil probe will be able to help you track it down. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet in length and width. Investigate the tank’s circumference to determine its edges and mark them with a marker. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into half for a two compartment tank) should show the position of the lid or lids if you are unable to feel them with your fingers.

A foul odor, if not deadly, vapors, are likely to emanate from within the tank itself. Keep your joy at having located your tank, but leave any maintenance or repair work on it to a team of experienced plumbers.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank.

Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build. As a result, and due to the fact that it requires constant pumping, you’re very certain to discover it in a location that can be reached by a huge truck while looking for it.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

3.

Almost usually, your septic tank will be constructed near where the main sewage line exits your property.

Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.

When you do, that’s when your septic tank comes into play!

Look for the Lid.

You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.

Those areas should be excavated in order to disclose the lids.

Get in touch with the pros.

Lifting concrete lids will necessitate the use of specialized equipment.

A fall into an unprotected septic tank has the potential to be lethal.

Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it!

To book a plumbing service in Bastrop County, please contact us now!

Leave a Comment

Your email address will not be published. Required fields are marked *