How Do You Fond A Septic Tank? (Solution found)

Follow the Main Sewer Line Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside. The sewer pipes will lead to where your septic tank is located.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

How do you find a septic tank in an old house?

Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.

Can a metal detector find a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How deep is a septic tank in the ground?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.

How do I find out if my septic tank is registered?

Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.

Do I have to change my septic tank?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

Can I drive over my leach field?

Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

How often should a 1000 gallon septic tank be pumped?

For example, a 1,000 gallon septic tank, which is used by two people, should be pumped every 5.9 years. If there are eight people using a 1,000-gallon septic tank, it should be pumped every year.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

How To Find My Septic Tank

1. What is a septic tank
2. How do I know if I have a septic tank
3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

“How can I locate my septic tank?” is one of the most often requested inquiries we receive.

When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.

The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.

In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

1. A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
2. A septic system is likely to be installed in your home if you reside in a rather rural location.
3. Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
4. When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
5. Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

1. If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
2. The county health department is responsible for keeping track of septic systems.
3. A septic tank’s position could be depicted on a survey map, for example.
4. The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

• In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
• By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
• The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
• Going via the sewage line itself is another method of locating the septic tank utilizing it.
• Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
• When the snake comes to a complete halt, it has almost certainly reached the tank.
• While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
• When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

• Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
• Directly in front of the home Immediately adjacent to your well (if you have one)
• In close proximity to trees or densely planted regions
• In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job

How Your Septic System Works

Underground wastewater treatment facilities, known as septic systems, are often employed in rural regions where there are no centralized sewage lines. They clean wastewater from residential plumbing, such as that produced by bathrooms, kitchen drains, and laundry, by combining natural processes with well-established technology. A conventional septic system is comprised of two components: a septic tank and a drainfield, often known as a soil absorption field. It is the septic tank’s job to decompose organic matter and to remove floatable stuff (such as oils and grease) and solids from wastewater.

Alternate treatment systems rely on pumps or gravity to assist septic tank effluent in trickling through a variety of media such as sand, organic matter (e.g., peat and sawdust), constructed wetlands, or other media to remove or neutralize pollutants such as pathogens that cause disease, nitrogen, phosphorus, and other contaminants.

Prior to discharging wastewater into the environment, several alternative systems are designed to evaporate or disinfect the effluent.

Specifically, this is how a typical conventional septic system works:

1. All of the water that leaves your home drains down a single main drainage pipe and into a septic tank. An underground, water-tight container, often composed of concrete, fiberglass, or polyethylene, serves as a septic system’s holding tank. Its function is to retain wastewater for a long enough period of time to allow particles to sink to the bottom and form sludge, while oil and grease float to the surface and produce scum. Sludge and scum are prevented from exiting the tank and moving into the drainfield region by compartments and a T-shaped outlet. After that, the liquid wastewater (effluent) exits the tank and flows into the drainfield. The drainfield is a shallow, covered hole dug in unsaturated soil that serves as a drainage system. Porous surfaces are used to release pretreated wastewater because they allow the wastewater to pass through the soil and into the groundwater. In the process of percolating through the soil, wastewater is accepted, treated, and dispersed by the soil, finally discharging into groundwater. Finally, if the drainfield becomes overburdened with too much liquid, it can flood, causing sewage to flow to the ground surface or resulting in toilet backups and sink backups. Finally, wastewater percolates into the soil, where it is naturally removed of harmful coliform bacteria, viruses, and nutrients. Coliform bacteria are a kind of bacteria that may be found in the intestines of humans and other warm-blooded animals, with humans being the most common host. As a result of human fecal contamination, it is a sign of this.

The Guadalupe-Blanco River Authority has built an animated, interactive model of how a residential septic system works, which you can view here.

Do you have a septic system?

It’s possible that you’re already aware that you have a septic system. If you are not sure, here are some tell-tale symptoms that you most likely are:

• You make use of well water. In your home, the water pipe that brings water into the house does not have a meter. In the case of a water bill or a property tax bill, you will see “$0.00 Sewer Amount Charged.” It is possible that your neighbors have a septic system

How to find your septic system

You can locate your septic system once you have confirmed that you have one by following these steps:

• Taking a look at the “as constructed” drawing of your house
• Making a visual inspection of your yard for lids and manhole covers
• Getting in touch with a septic system service provider for assistance in locating it

Failure symptoms: Mind the signs!

A bad odor is not necessarily the first indicator of a septic system that is failing to work properly. Any of the following signs should prompt you to seek expert assistance:

• Water backing up into the drains of homes and businesses
• It is especially noticeable in dry weather that the drainfield grass is bright green and spongy. The presence of standing water or muddy soil near your septic system or in your basement
• A strong stench emanating from the area surrounding the septic tank and drainfield

How to Locate Your Septic Tank

It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.

This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.

How To Find A Septic Tank: Step By Step

It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.

1. Gather Some Helpful Tools

Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.

Using this method, you may also locate the cover for your septic tank.

While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.

2. Use a Septic Tank Map

If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.

3. Start Ruling Areas Out

The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:

• Immediately adjacent to your well
• Beneath your home
• Directly against your home
• For example, underneath your driveway
• Under trees
• And other locations. Structures like a patio or deck are good examples of this.

4. Inspect Your Property

If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.

When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.

The likelihood of your septic tank being discovered in a few specific locations is quite high.

• Your water well, if you have one (for a variety of reasons that are rather clear)
• Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
• Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
• Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping

5. Inspect Your Yard

A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:

• If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
• Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.

The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.

6. Follow Your Sewer Main/Sewer Pipes

Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.

The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.

If the line is labeled, it is usually made of plastic or rubber. It is important to determine where this line exits your property and in which direction it is moving, as it often travels straight out to the septic tank itself.

7. Check Your Property Records

Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.

If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.

What to Do Once You Find Your Septic Tank

Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities. You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!

Looking for Your Septic Tank? Here’s How to Find It

“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.

Why you need to know where your septic tank is located

If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.

In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.

How to find your septic tank

1. Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
2. Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.

After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank.

When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.

• The post was published on July 16, 2019 under the category Septic Tank System.

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

• 3.
• Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
• Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
• When you do, that’s when your septic tank comes into play!
• Find the Lid.
• You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
• Those areas should be excavated in order to disclose the lids.
• Get in touch with the pros.
• Lifting concrete lids will necessitate the use of specialized equipment.
• A fall into an unprotected septic tank has the potential to be lethal.
• Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

How to find your Septic Tank at Home

When was the last time you paused to think about what happens to the things you flush down the toilet? It’s a little disgusting to think about, isn’t it? It’s possible that you’re conjuring up images of cobwebby crawlspaces with a swarm of creepy-crawly unmentionable creatures sliding, slithering, creeping, or crawling over crusty, rusted, ooey-gooey piping that’s oozing slimy goo from every joint. If this sounds like something you’re picturing then you’re not too far off the mark. I sincerely hope you are.

1. That’s why I’d want to assist you in learning how to locate your septic tank.
2. Simply dial 911 and ask for assistance in a calm manner.
3. Most hide-and-seek games are won by septic tanks, which are well-known for their amazing ability to outperform the typical human rival.
4. The good news is that.
5. Contrary to common misconception, septic tanks are not often found in attics, basements, or any of the numerous closets that may exist in a house or apartment.
6. Relax in your favorite place for a few minutes with your favorite beverage in hand.
7. Yes, you read that correctly: your yard.

Alternatively, you can sink.

Or whatever it is that’s causing the terror to rise in your chest to rise in your chest.

Septic tanks are normally installed in one of your backyards or on your property.

How are you doing?

If your septic tank is in close proximity to your well, this should be avoided.

Septic tanks are often located on the other side of a house from where your home is located.

Tanks are often placed with their tops buried beneath the surface of the ground, usually at least 12 inches below the level of the ground’s surface.

A plastic access tube or a concrete riser structure that runs from the top of the tank to the ground level will often be included to give access for a Septic Pumping firm to empty the tank. Shankster Brothers (also known as Shanksters)

Many septic tank installers will attempt to blend these access risers into the surrounding landscaping so they don’t create an ugly eyesore.

So the next step is to mentally go about your yard, looking for any circular, plastic lids that could be lying around. These can range in size from 10 inches to 24 inches in diameter and can be either black or green. Second, if the answer is no, consider any round, square, or rectangular concrete lids that may be present in your yard or landscaping as a possible source of contamination. Often, they will be practically flat with the surface of the ground, allowing a lawnmower or rake to pass directly over the top of them without causing damage.

• Typically, the septic tank access will be no more than 10 feet away from your home, but in the event of an older home or a subsequent addition to the property, they may be closer than that.
• Hopefully, you have a basement to store your belongings.
• If your home does not have a basement or crawlspace, we will rely on other indications to locate your home.
• All of these pipes should converge into a single bigger pipe (usually 4 inches in diameter) that exits the house via one of the home’s walls.
• Now it’s time to go outdoors.

Check the area where the pipe comes out of the house. There may be a PVC pipe extending to the surface, with a threaded cleanout cap on it. If you find this, you’re well on the way to victory.

Take a check at the roof if your property is constructed on a slab with no basement or crawlspace beneath it. Check the roof for a vent pipe that is coming out of it. An internal vent that travels straight up, through the roof, and out the top of your home is common. If you can identify that vent, it might be possible to figure out where the pipe is departing the house. Continue walking outside from the house for a few steps, keeping an eye out for that round, square, or rectangular cover. If you can’t discover it, check for a little sunken place in the yard that could be hiding anything.

If you notice one of those, you might want to look underneath it to see if there is an entry point hidden there.

It’s possible that here is where your tank is lurking. If none of these suggestions have resulted in victory, and you begin to observe your neighbors peering through their blinds with those anxious glances that neighbors are so prone to giving.give us a call!

We have foundseptic tanksin many strange and unpredictable places. Here’s hoping you win the game on how to find your septic tank. Here tanky, tanky, tanky! If you need to schedule aseptic tank cleaning, pumping, or inspection, don’t hesitate to call Shankster Bros at(260)-982-7111. any time.

What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00

How Do I Find My Septic Tank

Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.

A tiny proportion of septic tanks have a capacity of 3000L or more.

Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.

If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

1. They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
2. Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
3. A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
4. Using an electronic service locator, you may locate a septic tank.
5. In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
6. Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
7. Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

• There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.

Check the rest of the toilets in the home by repeating the procedure.

Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.

a link to the page’s load

How Does a Septic Tank Work?

Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.

How does a septic tank work?

Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.

It’s critical to understand how a septic tank works in order to maintain one.

Let’s take a look below ground and observe what happens in a properly operating septic system, shall we?

Understand that a septic system is a cafeteria for bacteria

Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.

• A layer of sludge settles to the bottom of the container.
• 4.
• Scum is mostly constituted of fats, greases, and oils, among other substances.
• Grease and oils float to the surface of the water.
• (5) A filter stops the majority of particles from reaching the exit pipe.
• The effluent is discharged into the drain field.
• Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.

When gravel is used to surround pipes, water can run into the soil and oxygen can reach germs. The garbage is completely decomposed by aerobic bacteria found in gravel and dirt. 9. Potable water seeps into the groundwater and aquifer system from the surface.

Septic Tank Clean Out: Don’t abuse the system

Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank. However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.

• Drains are used to dispose of waste that decomposes slowly (or not at all). Cigarette butts, diapers, and coffee grounds are all known to cause issues. Garbage disposers, if utilized excessively, can introduce an excessive amount of solid waste into the system. Lint from synthetic fibers is emitted from washing machine lint traps. This substance is not degraded by bacteria in the tank and drain septic field. Bacteria are killed by chemicals found in the home, such as disinfecting cleansers and antibacterial soaps. The majority of systems are capable of withstanding limited usage of these goods, but the less you use them, the better. When a large amount of wastewater is produced in a short period of time, the tank is flushed away too quickly. When there is too much sludge, bacteria’s capacity to break down waste is reduced. Sludge can also overflow into the drain field if there is too much of it. Sludge or scum obstructs the flow of water via a pipe. It is possible for tree and shrub roots to obstruct and cause harm to a drain field. Compacted soil and gravel prevent wastewater from seeping into the ground and deprive germs of oxygen. Most of the time, this is caused by vehicles driving or parking on the drain field.

Get your tank pumped…

Your tank must be emptied on a regular basis by a professional. Pumping eliminates the accumulation of sludge and scum that has accumulated in the tank, which has caused the bacterial action to be slowed. If you have a large tank, it may be necessary to pump it once a year; but, depending on the size of your tank and the quantity of waste you send through the system, you may go two or three years between pumpings. Inquire with your inspector about an approximate guideline for how frequently your tank should be pumped.

…but don’t hire a pumper until you need it

Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.

Install an effluent filter in your septic system

Garbage from your home accumulates into three distinct strata. The septic filter is responsible for preventing blockage of the drain field pipes.

Septic tank filter close-up

The septic tank filter is responsible for capturing suspended particles that may otherwise block the drain field pipes. Obtain an effluent filter for your tank from your contractor and place it on the outflow pipe of your tank. (It will most likely cost between $50 and $100, plus labor.) This device, which helps to prevent sediments from entering the drain field, will need to be cleaned out on a regular basis by a contractor to maintain its effectiveness.

Solution for a clogged septic system

If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.

1. Keep the effluent filter in place since it is required by your state’s health law.
2. Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
3. Your filter, on the other hand, should not require cleaning every six months.
4. A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
5. A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
6. Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.

For additional information on what should and should not be flushed down the toilet, contact your local health authority. More information on removing lint from your laundry may be found here.

Get an inspection

Following a comprehensive first check performed by an expert, regular inspections will cost less than $100 each inspection for the next year. Your professional will be able to inform you how often you should get your system inspected as well as how a septic tank functions. As straightforward as a septic system appears, determining its overall condition necessitates the services of a professional. There are a plethora of contractors who would gladly pump the sludge out of your tank, but many, in my experience, are unable to explain how a septic system works or how it should be maintained.

A certification scheme for septic contractors has been established in certain states; check with your state’s Secretary of State’s office to see whether yours is one of them.

Also, a qualified inspector will be able to tell you whether or not your tank is large enough to accommodate your household’s needs, as well as the maximum amount of water that can be passed through it in a single day.

As you learn more about how a septic tank works, your professional should be able to tell you whether or not your system will benefit from this treatment.

Alternatives to a new drain field

If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.

• Pipes should be cleaned. A rotating pressure washer, used by a contractor, may be used to clean out the drain septic field pipes. The cost of “jetting” the pipes is generally around $200. Chemicals should be used to clean the system. A commercial product (not a home-made one) that increases the amount of oxygen in the drain field should be discussed with your contractor before installing your new system. Septic-Scrub is a product that I suggest. A typical treatment will cost between $500 and $1,000. Make the soil more pliable. The process of “terra-lifting,” which involves injecting high-pressure air into numerous locations around the drain field, is legal in some states. Some contractors use it to fracture compacted soil around the pipes. Depending on the circumstances, this might cost less than $1,000 or as much as $4,000 or more.

Protect your drain septic field from lint

When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.

Don’t overload the septic system

Reduce the amount of water you use. The volume of water that flows into your tank, particularly over a short period of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to save water.

Meet the Expert

Septic systems, according to Jim vonMeier, are the solution to America’s water deficit because they supply cleaned water to depleted aquifers, according to vonMeier. He travels the country lobbying for septic systems, giving lectures, and giving testimony. For septic system inquiries, as well as information on the operation of the septic tank, contact him by email.