How To Locate Rural Septic Tank Lid? (Solved)

Probe around the tank to locate the edges and mark the perimeter. If you do not feel the lid by probing, a shallow excavation with a shovel within the perimeter and near the center (or broken into halves for a two compartment tank) should reveal the location of the lid or lids.

You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath. You can also use a metal detector, as most lids have a metal handle or fastener on them to keep the lid closed.

How far down is my septic lid?

Dig Up The Lids Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

Will metal detector find septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

Do septic tanks have two lids?

Locate The Lid A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

Do I have to change my septic tank?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

What is OWTS?

An Onsite Wastewater Treatment Systems (OWTS) is a privately owned and maintained sewage disposal system. They are commonly referred to as septic systems. All OWTS have two basic components: a two-compartment septic tank and a disposal field.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.

Are septic tanks metal?

Steel Septic Tank—Steel septic tanks are the least durable and least popular tank option. Designed to last no more than 20-25 years, they can be susceptible to rust even before that. Steel top covers can rust through and cause an unsuspecting person to fall into the tank.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

How to Find A Septic Tank Lid?

Disclosure: This post contains affiliate links, which means that if you purchase a product after clicking on one of our links, we may receive a commission or free product from the firms featured in this post. Amazon is a good illustration of this. Because the septic tank is so enormous, you would think it will be simple to locate a septic tank lid. However, keep in mind that the lid is buried deep beneath and is not usually visible from above the surface of the earth. The good news is that there are several simple methods for finding the septic tank lid when you need it.

So, what is the best way to locate a septic tank lid?

In order to locate the lid, a metal probe is utilized to identify the edges and label the perimeters of the container.

Continue reading to learn about other methods of locating a septic tank lid, how a metal detector may be used to assist in the search, and whether it is possible to locate the lid on your own.

CALL 855.925.0760 FOR SEPTIC SERVICES

Every homeowner is responsible for knowing where their septic tank is placed. If you know where your septic tank is located, it will be much easier to detect the many issues that may be affecting it. In the case of flooding directly at the septic tank lid, you will know that there is an issue with overloading. Furthermore, once you know the position, you may make certain that no cars are parked on top of it. It is possible that the lid will collapse if cars are parked or move over it. The entire septic system will come crashing down.

As a result, it assists in saving both money and time.

CALL 855.925.0760 FOR SEPTIC SERVICES

If you are not the original owner of your property, it is possible that you will not be aware of the exact position of the septic tank. Here are a few pointers to keep in mind when looking for septic tank covers.

Follow the Sewage Pipes — It is important to remember that the drainfield and septic tank are often constructed in a line with the sewer lines. The sewer line runs from the house to the backyard. The 4-inch sewer pipe will be found in the basement, since it is the conduit that connects the house to the sewer system.

Simply follow this pipe all the way across your property. Continue probing the ground every 2 feet for the rest of the day. Tanks are typically placed at least 5 feet away from the home. These are typically between 10 and 25 feet distant from the subject.

Investigate the County Construction Permit Records –Counties often maintain account of their building permits, which may include the installation of a septic system. This is offered with a graphic as well as the necessary measurements. It aids in the identification of the septic tank on the site

In addition, a schematic of the septic system will be included in the house inspection documentation. Check for information such as the distance between the tank and the side of your house or the sewer outflow, among other things. Keep in mind, however, that historical landmarks are always changing.

Dig the Lids — Depending on the septic tank configuration, there may be two or three lids on the septic tank. Most septic systems are rectangular in design, measuring 5 feet by 8 feet in size. The components are typically buried between 4 inches and 4 feet below the surface of the earth. Finding the lid by probing with a metal object is beneficial. In addition, you can excavate with a shovel, which should disclose the lid of the container.

CALL 855.925.0760 FOR SEPTIC SERVICES

Any ancient property might be difficult to navigate while trying to locate the position of the septic tank’s lid. In order to accomplish this, you will require probes or metal detectors. When it comes to locating septic system components such as the lid, these are fantastic tools. In order to locate a septic tank lid on an ancient property, you will want expert assistance.

However, due to the fact that older homes include several levels of pipes and cables, caution should be exercised. These can be deceptive, and they can lead to problems in reading comprehension. Learn more about how a septic system works by reading this article.

Where are Most of The Septic Tanks Located?

For anyone seeking for septic tank lids, it is necessary to be familiar with the basic location of these tanks. This type of structure is often built between ten and twenty feet away from your home. If you are unable to locate the septic tank or if it has been buried, you can look in the crawl space or the basement. You will come across the sewer lines that are exiting the property at this location. In most cases, the septic tank will be located outside, close to where the sewer pipe terminates.

CALL 855.925.0760 FOR SEPTIC SERVICES

It is your obligation to ensure that the septic tank is in good working order after it has been identified. There are no damages to the and it is simple to get to when professionals return to their homes. In order to guarantee that the septic tank lid is properly maintained, you may do the following:

You should make a habit of periodically clipping the grass that likes to grow around the lid. You may clean away any debris or grime that has accumulated on the lid. Anything that extends over the lid is not permitted – even flower pots are not suggested. A car should not be parked on anything erected above the system
You should also make certain that no weight is placed on it. Place a garden décor object, such as a beautiful rock or a flag, just above or alongside the lid to serve as a marker for where the lid is

By marking the position of the septic tank, you will not have to spend additional time looking for it the next time you need to.

CALL 855.925.0760 FOR SEPTIC SERVICES

If the septic tank was erected prior to 1975, it will have a single lid to protect it. This is a 24 inch lid that sits perfectly in the middle of the rectangular shape. A two-compartment tank, or one that was added after 1975, will have two covers, one on each compartment. These are often built towards the end of a rectangle’s length and width. The process of opening and closing a septic tank lid can be difficult, especially if you do not have the proper tools. You’ll need a pry bar to get it out of the way.

The prybar has been placed in the proper position.

With the help of this tool, you may effortlessly remove the lid from its hole.
You may place this cover on top of the surface.
There are two baffles in the tank: an inlet baffle and an exit baffle, if there are two baffles in the tank.

As a result, the tank settles and distinct strata begin to form.
You should make sure that the location of the lid is clearly marked so that no one drives over it, even by accident.
The lid should not be searched for if there is an emergency and specialists are called to your home.

CALL 855.925.0760 FOR SEPTIC SERVICES

What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00

How Do I Find My Septic Tank

Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.

A tiny proportion of septic tanks have a capacity of 3000L or more.

Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.

If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system. To learn more about our wastewater treatment plant, please visit our Waste Water Treatment Plant website.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.

A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
Using an electronic service locator, you may locate a septic tank.
In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.

Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.

Check the rest of the toilets in the home by repeating the procedure.

Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.

a link to the page’s load

How to Find a Septic Tank

A septic tank is big, and it is tempting to believe that keeping track of it will be a simple chore. However, if your septic tank lid is buried underground, as is frequently the case, it may be a little more difficult to locate than you may expect. Certain circumstances may apply, particularly if you are not the original owner of the home or land. It is possible that you will not know where to begin looking if you are not knowledgeable. If you own a large piece of land, things have just gotten a little more complicated for your family.

We’ve compiled a list of suggestions based on our own personal experiences that we believe may be useful in making the process a bit less difficult.

(+1) 478-3721 (252) 478-3721

Follow the Sewer System Pipes

Septic tank installation methods vary, but the most usual is to place the tank and drainfield parallel to the sewage line that extends from your home to the sewer main. Look for a 4-inch sewage pipe in the basement or crawl area of your home, which indicates the location of the point where the septic system exits the house. To probe the ground every 2 to 3 feet or more, slowly and carefully follow the pipe across the yard, probing every 2 to 3 feet or more. According to rules, the septic tank should not be located closer than 5 feet from the home.

Check and Review County Records

Checking with the county records might be beneficial, especially if you are not the original owner of the property. Most counties maintain records of all building permits issued, as well as the installation of septic systems on each individual property. Most of the time, the documents will include a schematic with dimensions that depicts where on the land the septic tank is located. Additionally, a home inspection was performed prior to the purchase of the property, and the report may include a schematic of the septic system.

Particular attention should be paid to landmarks, because they have a tendency to alter through time.

Schedule Maintenance

You should call Brantley Septic regardless of whether you were successful in identifying your septic tank. They can arrange for a comprehensive maintenance and inspection. One thing to keep in mind is that you should never attempt to open the tank yourself. Because of the weight of concrete septic tank lids, it is possible that special lifting gear may be necessary for their removal. Most significantly, due to the potentially harmful wastes and poisonous gases present in an open tank, it may be extremely dangerous.

If you are unable to locate your septic system lids, or if you prefer that Brantley Septic locates them for you, you can skip the steps outlined above and simply contact us.

When the Work is Done, Disguise the Lids

Following the time-consuming procedure of locating your tank, digging up the lids, and installing risers, you should ensure that the area is kept clear and visible so that you do not have to repeat the process the next time your septic tank requires repair. Septic tank lids, on the other hand, can be a bit of an eyesore! The use of an object such as a lightweight plastic pebble, a birdbath, or a planter box to conceal your lids in plain sight are some examples of how you may conceal your lids in plain sight.

Schedule service online or give us a call at (252) 478-3721 right now.

How To Locate Septic Tank Cap

In most cases, a septic tank cap, also known as a lid or an access hatch, is positioned towards the middle of the tank on the tank’s top. Is it difficult to locate your septic tank because of snow on the ground? If you have an old house with a septic tank entrance that’s not functioning properly,

How to find your septic tank 1.

In most cases, a septic tank cap, also known as a lid or an access hatch, is positioned towards the middle of the tank’s top. Is it difficult to locate your septic tank because of snow on the terrain? If you have an old house with a septic tank entrance that’s not functioning properly, you should consider replacing it.

Everything You Need To Know About Your Septic System

Florida people rely on roughly 2.6 million septic systems to dispose of waste and wastewater on a daily basis, accounting for 30% of the state’s population. Homes and businesses in rural regions rely on these systems to dispose of garbage in an efficient and environmentally friendly manner.

What Are Septic Tanks Made From?

Septic tanks are a waterproof box composed of concrete, fiberglass, or polyethylene material that is used to dispose of sewage. In other words, there will be no debris, dirt, or water from the surrounding ground that may get into the tank. Septic tanks made of concrete and/or fiberglass are the most common types.

Common Styles Of Septic Tanks

Septic tanks are waterproof containers constructed of concrete, fiberglass, or polyethylene.

In other words, there will be no trash, dirt, or water from the surrounding ground able to enter the tank. Septic tanks made of concrete and/or fiberglass are the most common.

Double Compartment

Most tanks built since 1976 feature two compartments for filtering effluent, sediments, and wastewater that enters the tank during the construction process. The first compartment, which is placed adjacent to the intake pipe, is often bigger than the second compartment, which is located further away. It is possible to see the liquid flowing from the first container into the second compartment. Before the effluent is discharged into the outflow pipe, any remaining sludge and scum separate from the liquid.

Pump Tank

The quantity of wastewater that flows from the septic tank is controlled by a pump tank. Pump tank level increases as effluent accumulates in the tank and eventually reaches the level set by a control float. As soon as the float is activated, the pump starts pumping effluent into the drain field in a predefined volume.

Holding Tank

In lieu of septic tanks, holding tanks can be used to collect and store waste. They are either above or below ground and require constant pumping to remove the contents of their holding tanks. The majority of holding tanks are equipped with an alarm that sounds when the tank is full.

Single Compartment

A single compartment tank was utilized in the majority of septic systems constructed before to 1976. These tanks could hold up to 1,000 gallons of liquid at a time. After entering the tank and separating into three levels, liquid waste is discharged into the septic drain field via the outflow line.

What Is FOG?

Fats, oils, and grease (also known as FOG) are frequent cooking byproducts that occur naturally in a wide variety of foods and other items. While FOG is viscous when it first enters the septic tank, it cools swiftly as it comes into contact with the wastewater in the tank. However, because of its viscosity, FOG coats and covers every surface it comes into contact with when it solidifies.

How A Septic Tank Works

Solids sink to the bottom of the tank’s intake pipe, while FOG rises to the surface of the wastewater and collects at the top of the tank’s intake pipe. In most cases, the tank is large enough to keep wastewater for an extended period of time, allowing effulent separation to take place. There are three levels within the tank as a result of this separation: a sludge layer on the bottom, a wastewater layer in the middle, and a scum layer on top. bacteria, enzymes, and other microorganisms often present in human waste begin to break down the sludge layer and break down the sludge layer further.

Upon entry into the septic tank and drain field, two baffles direct and filter the water.

What Are Septic Tank Solids?

The majority of solids contained in a septic tank may be divided into three categories:

Non-biodegradable organic solids include pet litter, plastics, and other items that do not decompose over time

Biodegradable organic solids include vegetable scraps and other cellulosic compounds, as well as toilet paper
And biodegradable organic solids include solid human feces.

Septic System Drain Fields

After leaving the septic tank, effluent goes into a drain field, which is a network of underground pipes and dirt that collects the waste.

Other phrases that are commonly used include absorption field, leach field, and trench. The size of the space required is determined by the following factors:

Soil type
Seasonal variations in groundwater level
Amount of water absorbed each day

And soil percolation rate are all factors to consider.

The soil percolation rate is defined as the amount of water that the soil can absorb in one minute per inch of soil thickness. A significant consideration in determining the site of a septic drain field in Florida is the percolation rate, which is crucial because the state has a high water table.

How A Drain Field Works

An underground network of perforated pipes may be found in this location, which can be found in either several trenches or a gravel-lined soil bed. Drainage from the pipes filters through the gravel and dirt before entering the sewer system. Compaction of the soil has a significant impact on its function, which is why it is critical not to construct structures on it or drive or park vehicles of any size over it.

Why Is A Drain Field Important?

Natural filtration is provided for effluent, which is recycled back into the groundwater source. It is possible that biological and chemical pollutants may infiltrate the water and create health problems for anybody who consumed or came into touch with the water without this filtering system in place.

How To Find Your Septic TankSeptic Drain Field

The location of the septic system will be shown on the majority of property plans and surveys. Possibly handed to you after the sale of your house or company, these documents are also maintained on file at the county government office. The septic tank is often built along the sewage line that leads away from the house or other structure. When this line is many inches in diameter, it means that it is located at the lowest level of your home, such as a basement or crawl space. Stick a metal probe every two feet along the sewage line as it exits the house, following it all the way out to the street.

Locate the borders of the septic tank lid with the probe – typically tanks are 5 feet by 8 feet in size, so this may take some time.

As soon as you discover a discrepancy between the system location and previously prepared diagrams or maps, make sure to update these materials and retain a duplicate for your records.

The Septic Tank Pumping Process

In order to prepare for extraction, the floating scum layer is first broken up by alternately sucking out liquid from the tank and pumping it back in to break up the bottom solid layer. Pumping is accomplished through the two access ports, which are referred to as manholes. The tank should never be pumped through the inspection apertures on the baffle wall. This can not only cause damage to the baffles, but it can also result in insufficient waste removal from the tank. Until the septic tank is completely depleted, industrial vacuums are used to remove waste from the tank and into our tanker truck.

How Often A Septic Tank Should Be Pumped?

In most cases, every three to five years is sufficient.

However, depending on the size of your septic tank and the amount of sediments and wastewater you produce on a daily basis, you may need to contact a septic tank pumping firm such as Jones PlumbingSeptic Tank Service sooner rather than later.

What To Expect During A Septic Tank Pumping

Before starting the pumping process, it is necessary to measure the thickness of the scum and sludge. This information is important in determining the pace at which waste accumulates and in determining when the next pumping should be scheduled. The pumping process is monitored closely by our personnel, who are actively monitoring for any possible system problems, such as backflow from the outflow pipe. Backflow that is significant typically indicates a backup in the drainfield, whereas slight backflow indicates a weaker outflow line in most cases.

Septic Tank Cleaning

Septic tank cleaning and septic tank pumping are not the same thing, despite the fact that many people use the phrases interchangeably. Pumping just removes liquid and uncompressed materials; cleaning, on the other hand, eliminates any leftover solids before washing the interior of the tank with soap and water. Following the removal of the liquid layer from the tank, our professionals employ pressured jets of water to break up any residual particles in the tank. Solids are removed from the tank with the use of an industrial-grade vacuum and a connected hose before the inside of the tank is washed.

This can result in the formation of sinkholes or the breakdown of the entire system.

How Often Should A Septic Tank Be Cleaned?

With every septic tank pump out, there is a new beginning. Keep in mind that the frequency with which the tank is pumped is determined by the number of people who are using the system and the volume of wastewater created on a daily basis. You may work with an aseptic tank pumping firm, such as Jones PlumbingSeptic Tank Service, to establish a regular pumping and cleaning program for your tank.

How To Keep A Septic Tank In Good Condition Between Cleanings

The most effective strategy to ensure that your septic tank remains in good working order for many years is to be informed of what can and cannot be put into the system.

Don’t DisposeFlush Items At-Will

In order to degrade materials that enter the tank, a septic system relies on bacteria that are found in nature. Although it is a mutually beneficial connection, it is susceptible to being pushed out of balance depending on the materials that are disposed of. Fat, oil, and grease (FOG); chemicals, paints, fuels, and/or motor oils; disposable diapers, sanitary, and personal hygiene products; coffee grounds; egg and nut shells; and disposable diapers, sanitary, and personal hygiene products are all common household items that should never be flushed down the toilet.

Schedule Annual Inspections

Home and business owners may do an outside inspection of their septic system on their own. However, only a professional and skilled septic tank firm, such as Jones PlumbingSeptic Tank Service, should check the tank and its interior components. Because of the formation of toxic vapors and gases within the sewage treatment plant, it is dangerous to work near one without the proper safety equipment and training.

Look for areas of unusually tall grass, sewage odors or smells, and unexplained standing water as you walk around the area where the septic tank is situated. These symptoms are typically connected with septic systems that are in need of repair.

PumpClean The Tank As Necessary

Skipping regular septic tank services is a surefire way to end yourself in a situation that might have been avoided. Performing routine pumping and cleaning allows our personnel to check the overall health of the system and correct any issues that may arise before they become a major concern.

Keep Records Of Septic LocationService

It is essential to understand the location of the entire system in order to properly maintain it. Parking or driving cars over any portion of the septic system should be avoided at all costs. The weight of vehicles can cause the system to collapse. When this occurs, the only option for repair is a complete replacement. It is also recommended by Jones PlumbingSeptic Tank Service that you preserve records of when the system was examined, pumped, and cleaned for your own records and in case you decide to sell your home in the future.

Conserve Water

The volume of water entering a septic system has a greater influence on the health of the system than the amount of solids created by the system. The greater the volume of water that flows through the drain field, the shorter the functional lifespan of the drain field and the overall system. An excessive amount of water flow impairs effective separation of particles inside the tank, increasing the likelihood of clogged intake and outflow pipes, which can result in sewage backups in the tank.

Septic Tank Repair In Gainesville, FL

Too much water in the septic tank increases the likelihood of sediments being transferred into the pipes, which might result in a clogged system.

Aggressive Tree Roots

Tree roots are well-known for generating problems with septic tanks and systems. Many species of tree roots are stronger than septic tanks, and they can cause leaks and other structural damage by cracking the pipes and tank.

Common Septic Tank Repairs

There are a variety of reasons why the pipes might fail, including compacted and/or moving soil. Once the pipes burst, they must be fixed as soon as possible to avoid significant drainage problems. When it comes to reaching and repairing the pipes, excavation of the area is frequently necessary.

Broken Baffles

The baffles of a septic tank are responsible for keeping sediments contained within the tank. Rust or contact with sulfuric acid are the most common causes of damage. It is quite beneficial to have an annual septic check performed in order to see if there are any difficulties with the baffles before a problem occurs.

How To Prevent A Septic Tank Failure

The fact is that septic systems are not foolproof and that they benefit immensely from routine maintenance and upkeep. The majority of failures may be avoided by paying attention to what goes into the plumbing and septic lines.

Only Flush Toilet Paper

As a rule, toilet paper degrades and disintegrates more quickly than other types of paper goods. Particularly problematic are paper towels and wet wipes, which are two of the most prevalent causes of septic tank clogging and premature tank cleanouts.

Never Pour FOG Down The Drain

FOG is extremely harmful to all plumbing systems, including the septic system. FOG, when it is in liquid form, readily flows into the septic tank and collects in the top scum layer of the tank.

This may not appear to be a problem, but the mixture has the potential to run into the drain field, where it might cause contamination concerns with groundwater and the surrounding soil if allowed to do so.

Regular Drain Cleaning

The numerous commercial drain cleaners available may temporarily unclog a clogged drain and associated plumbing, but they do so at the expense of the septic system’s ability to function properly. They include chemicals that swiftly eliminate the bacteria that are important for the decomposition of particles within the septic tank once they are applied. The layer of solids accumulates quickly — and needlessly — on the surface of the water. As an alternative, call a plumber to do expert drain cleaning.

How To Tell When You Need A New Septic System

A septic system may last anywhere from 20 to 40 years if it is maintained properly and repaired when needed on time. However, if you detect any of these frequent indicators of a failing septic system, it’s time to call Jones PlumbingSeptic Tank Service to have a new septic system installed in your home or commercial property. The following are common indicators that the present system should be replaced:

Sinks and toilets that take a long time to drain

Plumbing that is always backed up
Sewage odors in the company, house, or yard
Patchy mushy, swampy, or damp areas of the yard Gray water that has accumulated

And grass that has grown more swiftly and is a darker shade of green

What To Know Before A Septic Tank Is Installed

In order to prevent the contamination of water sources and the creation of public health hazards that can result from incorrectly designed septic systems, the state of Florida and local municipalities have established rules and regulations to guide new septic system installations.

Required Applications, FeesPermits

The Environmental Health Service of the Florida Department of Health (FDOH) in Alachua County is responsible for issuing the necessary applications and permits. Before a permit may be issued, the house or business owner must submit a completed application, as well as a site plan, a building floor plan, and any applicable application costs to the local building department. A site evaluation is also necessary, which analyzes the overall condition of the land, as well as the soil type. Total fees are determined on the kind of septic system installed as well as the services provided by the county health division.

Minimum Tank Size

A minimum 900-gallon capacity is required for all septic tanks in Florida; however, this capacity requirement rises based on the size of the occupancy and whether the system is intended for residential or commercial usage. The specialists at Jones PlumbingSeptic Tank Service can assist you in determining the right tank size that complies with local and state specifications.

Landscaping Changes

Because septic systems are installed underground, it is probable that the existing landscaping will need to be removed and replaced. Our professionals, on the other hand, may propose that the new system be installed in a different place in order to minimize interference with plant and tree roots. The Florida Department of Health mandates that the following distances be respected in order to prevent groundwater pollution from septic systems:

If the property is located more than 75 feet from the annual flood line of a permanent, non-tidal surface water body or from the high water line of a tidal body of water, the following restrictions apply: 15 feet from a dry drainage ditch or stormwater retention area

10 feet from stormwater pipelines
At least 200 feet away from public drinkable wells that are already in use for non-residential or residential structures with a total daily sewage discharge of more than 2,000 gallons
And At least 11 feet away from any water storage tanks that come into touch with potable or groundwater

A minimum of 15 feet away from a groundwater interceptor drain is required
Minimum distances between bays, lakes and surface water
Minimum distances between multi-family wells and/or private potable water wells

And minimum distances between other wells.

New Home ConstructionSeptic Systems

Construction of new dwellings in rural locations or in any area that is not served by a municipal sewer system necessitates the installation of septic systems. Any system installed as part of a new house building project will have to take into consideration the elements and laws outlined above.

In addition to establishing septic systems for countless new houses, Jones PlumbingSeptic Tank Service is happy to assist you through the application and permitting process, in addition to properly installing the system.

How to Find Your Septic Tank Lid

Previous PostNext PostWhether you realize it or not, it is critical that you be aware of the position of your septic tank lid and the septic tank itself. Despite the fact that septic tanks are fairly huge, they can be difficult to identify, particularly if they have not been properly maintained over time. Continue reading to find out how to locate your septic tank lid.

Why It’s Good to Know Where to Find Your Septic Tank Lid

Knowing the location of your septic tank is a fantastic approach to spot septic tank problems as soon as they occur. Consider the following scenario: If you saw water near your septic tank lid, you would know right away that you could have a problem with your system being overloaded with waste. Furthermore, by understanding where your septic tank is located, you may avoid parking cars on top of it, which might cause the tank to collapse and create flooding. You’ll also be able to point service personnel in the right direction for septic tank services, which will eventually save them time and money while also saving you money.

How to Find Your Septic Tank Opening

Knowing how critical it is to know where your septic tank lid is located, it’s time to go out and find one for yourself. Keep an eye out for a circular lid that is roughly two feet in diameter during your quest. Septic tank lids are normally constructed of green or black plastic, however they can occasionally be made of concrete. It is not always simple to locate the septic tank lid, however, because untidy vegetation, mud, or debris might obscure the lid’s location. If you live in a snowy climate, seek for a spot of lawn where the snow melts more quickly than it does anywhere else on the property.

How to Find Your Septic Tank Lid as a New Homeowner

During the process of purchasing your house, you should have been provided with a map of your property that showed the location of your septic tank. This is normally included as a part of your home inspection service package. All you have to do from there is compare the diagram to your land, find the septic tank location, and potentially dig around it to check whether the lid has been hidden by vegetation or other obstructions. People have been known to place an object such as a huge rock on top of the septic lid, so be sure to look beneath landscaping stones as well.

How to Find Your Septic Tank Lid as an Existing Homeowner

Still having trouble locating your septic tank lid? There’s a significant probability it’ll end up in the ground. The pipes coming from your basement should be followed, as they will take you in the direction of your septic system, which is what we propose. Then, once you’ve determined the correct direction, check for any high or low points in the yard that might reveal the location of your septic tank. You can find the lid of your septic tank by probing the ground with a metal probe every few feet with the probe.

Because most lids have a metal handle or fastener on them to hold the lid closed, you may also use a metal detector to find them.

The majority of lids are buried up to a foot deep, but some lids might be buried as deep as four feet in extreme cases! In some instances, a professional with specialized locating equipment may be required.

How to Maintain Your Septic Tank Lid

Following the discovery of your septic tank lid, keep it in good condition to avoid damage and ensure simple access for future septic tank maintenance, such as pumping your septic tank every three- to five-year period. Here are some pointers for keeping your septic tank lid in good working order:

Following the discovery of your septic tank lid, keep it in good condition to avoid damage and ensure simple access for future septic tank maintenance, such as pumping your septic tank every three- to five-year interval. For good maintenance of your septic tank lid, follow these suggestions:

Professional Septic Tank Services

Is it difficult to find trustworthy septic tank services or septic tank installation? If you are looking for septic tank installation, inspection, and cleaning services, check with your local Mr. Rooter ® Plumbing franchise. Mr. Rooter charges a set amount up front, with no overtime fees or additional expenses. To get started, call us at (855) 982-2028 or fill out our online estimate request form. Is the lid of your septic tank obscured by grass? Inquire with The Grounds Guys about routine lawn care and upkeep.

Rooter, is a member of Neighborly’s network of dependable home service experts, which includes Mr.

By hiring The Grounds Guys to provide trustworthy grass mowing and landscape care services, you can be assured that your septic tank lid will always be simple to locate.

How Deep Are Septic Tanks Buried? (And How Do You Find It?)

Is it difficult to find trustworthy septic tank maintenance or septic tank installation? For more information about septic tank installation, inspection, and cleaning, check with your local Mr. Rooter ®Plumbing location. With Mr. Rooter, you will never be surprised by an unexpected bill for overtime. To get started, call (855) 982-2028 or submit a request for an estimate online. Grass has grown up around the top of your septic tank lid. For more information on basic lawn maintenance, contact The Grounds Guys now.

Rooter and The Grounds Guys.

The preceding and next posts

You May Not Know

Despite the fact that it appears to be something that every homeowner should be aware of, understanding how deep a septic tank is buried can be difficult to determine. Perhaps you forgot about the septic tank after it was installed years ago, or perhaps you are moving into a house that already has a septic tank constructed in previously. Whatever the situation, determining the depth of your septic tank can be a challenging task under the circumstances, especially if you are unsure of the location of the lids.

How to Locate Your Septic Tank

Perhaps you’re unsure of the location of your septic tank on your property and are attempting to identify it on your own. There are really quite a few quick and simple methods for determining the location of your tank without having to go through a lengthy process. The first method is to follow the path laid out by your sewer lines. Typically, the tank and your drain field will be placed along a line parallel to the sewage line that goes from your property out to the street. Your home’s crawl area or basement may even have a four-inch sewage line that leads away from the structure of the building.

Follow the pipe all the way across the yard, checking every few of feet to make sure you’re still on the right track, and then turn around.
When you don’t feel like digging around in your yard, you can always look up your house’s address in the county records database.
Diagrams with measurements and even the particular location of where the septic tank is located should be included in this document.

You can also choose to dig your lid out from under it.
This is what will tell you how many lids are on your septic tank and how many are missing.
The majority of septic tanks are rectangular in shape and measure around in the neighborhood of 5′ x 8′ in size.
If you are unable to determine the position of your septic tank using a probe, you will need to do a shallow excavation around the perimeter of the tank using a shovel in order to finally locate the lid.
First, look for visual cues to help you.
There is no doubt about it, this will tell you exactly where the tank is located beneath.
Take a look at the plumbing in your structure, as well as the overall state of the property, to get a good sense of where the tank is situated.

It will be full to just a few inches below the underside of your tank lid when your tank is fully charged to its regular level of filling capacity. If the lid is constructed of plastic, fiberglass, or steel, the upper surface of the lid may have some variation in color or texture.

Where Should the Septic Tank Be Located?

If your property does not presently have a septic tank, but you are interested in the possibility of installing one, it is critical that you understand where it should be installed. Ordinarily speaking, most septic tanks will be situated between 10 and 25 feet away from the house. You should bear in mind that septic tanks cannot and should not be located any closer than five feet from your residence. Using a probe, you may search for flat concrete to determine whether or not a tank has previously been put on a property that you have recently purchased.

Planting Above a Septic Tank

Even though it may not appear to be the finest idea in the world, putting vegetation over a septic tank may really be perfectly acceptable as long as you choose the appropriate plants to grow. Not only is it perfectly OK to do so, but it may also be rather helpful depending on what you are planting and harvesting. It is possible to avoid erosion in your tank with the correct sort of vegetation, and it is even possible to absorb some of the additional moisture that might accumulate in your drain field.

Perennial plants and grasses (as previously indicated) are the ideal kind of plants to use in and around your drain field and septic tank.
You can use non-woody ground covers for a similar purpose as you do with woody ground covers.
Take, for example, the expanding environment.
If you don’t have access to enough sunshine, you might want to choose a shade garden plant instead.
Keep in mind that the soil that surrounds the septic tank drain field will typically be wetter than the surrounding soil in the rest of the yard.
As a result, choose a perennial such as a hollyhock, wild violet, or bee balm to ensure that you cover all of those bases when planting.
A septic system beneath these plants does not imply that deer will avoid the area because of its presence on your property.
Something like a spring bulb or an attractive grass that the deer aren’t generally interested in eating.

Plants That You Don’t Want to Grow

Just because you have the option of planting over your septic tank does not mean that everything is appropriate for this situation. A few plants should be avoided at all costs while landscaping around your septic tank, particularly huge trees that are known for their rapid growth. On the same vein, shrubs and trees with aggressive root systems are some of the worst plants to grow around your home. These roots will shoot out in quest of water, and they will not be concerned with where they locate it.

The infiltration of those roots into your septic drain field might result in catastrophic damage to your septic tank and drain field.

It’s possible that you’ll need a complete replacement.

Many other plants have strong root systems that you should avoid growing anywhere near your septic tank or drain field, and there are lots of them.

How Your Septic System Works

It is possible that understanding how your septic system operates may help you better manage, maintain, and care for it. Aside from that, it is just a large tank buried in the ground that collects your waste (which is true, but still). In remote locations, there may be a deficiency in sewage infrastructure. Because not every rural location is the same, it is not a given that septic systems will be required in your local rural area. The septic tank, in any case, serves as a form of wastewater treatment facility when there are no sewage lines available.

The tank is designed to be waterproof, ensuring that your wastewater does not leech into the surrounding environment.
Solids sink to the bottom of the container, scum rises to the top of the container, and liquids sit in the center of the three levels described above.
The wastewater that is being discharged from your home is the cause of the exit.
This liquid is carried out of your home through a pipe and into a bigger portion of your sanitary sewer system.
Your drain is typically comprised of a network of perforated PVC pipes that are put underground in trenches to collect water and waste.
Because the drains are perforated, the wastewater is allowed to seep out into the crushed gravel or stone, and then eventually into the surrounding soil.
The natural evaporation process will then take care of any surplus moisture in the soil, unless you do something to prevent the water from flowing out of the pipes.

How to Plan a Septic Field

The tank is only one component of the whole equation. You’ll also need a drain field to catch all of the liquid waste that will be generated. When you are planting around your septic tank, the drain pipes are the most significant source of worry. Having those aggressive roots infiltrate and ruin your septic drain system is the very last thing you want. When this occurs, it can prevent your septic tank from emptying correctly and potentially cause it to get contaminated by groundwater. According to a solid rule of thumb, the less horticultural labor you have to do in close proximity to your septic tank, the better.

Just remember that they must be planted every year, so keep that in mind while planting them.

The first step is to fill in the septic drain field with earth.

In the second instance, too much mulch is being applied to the area in question. The third issue is that you may be watering your plants more than you should be. All three of these factors can impair the capacity of your drain field to evaporate in a typical manner.