When Open Lids To Septic Tank They Are Both Full? (Solution found)

When you first open up a septic tank you will notice that the tank is full and close to the top with sewage. The first thought is typically that the tank is ready for pumping. However, this is the level that a tank normally operates.

Why does my septic tank have 2 lids?

Solid, watertight, buried tank made of concrete, plastic, fiberglass or metal. This tank has a way in (inlet), and a way out (outlet). So, most residential tanks should have (2) lids about 5′ away from each other. A septic tank holds all the liquid waste from your home (toilets, sinks, kitchen, bathtubs, floor drains).

Should a septic tank be full to the top?

Do not stand on the top of the tank as it could collapse due to concrete corrosion. The Septic Tank will be one of two types: A modern ‘onion’ shaped septic tank, in which case there will be only one lid with a ‘tube’ of around 600mm.

What are signs of a septic tank being full?

Here are some of the most common warning signs that you have a full septic tank:

Your Drains Are Taking Forever.

Standing Water Over Your Septic Tank.
Bad Smells Coming From Your Yard.
You Hear Gurgling Water.

You Have A Sewage Backup.
How often should you empty your septic tank?

Should both sides of septic tank be pumped?

Have your pumper pump both compartments of the septic tank. These are commonly called the “inlet” and “oulet” sides of the tank. While the inlet is absolutely necessary, the oulet is also good to have pumped.

Do all septic tanks have two lids?

A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

How far apart are the two lids on a septic tank?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

Why is my septic tank always full?

An overfilled septic tank is often a signal that your drain field is malfunctioning. The drain field is the final fixture in the septic system and serves the purpose of returning treated effluent back into the soil.

Can I shower if my septic tank is full?

Only the water would get out into the leach field in a proper system unless you run too much water too fast. The thing to do is to run your shower water outside into it’s own drain area, but it may not be allowed where you are. Used to be called gray water system.

What to do after septic tank is pumped out?

After you have had your septic tank pumped by a trusted septic company, there are some things you can and should do as the septic system owner.

1) Get on a Schedule.

2) Take Care of the System.
3) Know the Parts of Your System.
4) Check Other Possible Issues.

How do you know if your septic system is failing?

The first signs of a failing septic system may include slow draining toilets and sinks, gurgling noises within the plumbing, sewage odors inside, continuing drainage backups, or bacteria in the well water. The area of the strongest odor will point to the location of the failure in the septic system.

Why doesn’t grass grow over my septic tank?

Lawn grass species prefer moist, high pH soil, and direct sunlight. Growing grass over a septic tank can be challenging due to the acidic, low-pH soil resulting from sewage runoff into the leach field.

How often should you pump your septic tank?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

How often should a family of two pump their septic tank?

Septic tank pumping frequency The pumping frequency of the average septic tank varies from household to household. However, in general, you should pump your septic tank every three to five years, depending on a number of factors.

Can you pump your septic tank too often?

If your septic tank is pumped too often, that bacteria will have no place to go but out into the drain field, which can lead to clogs and failures. So unless your septic tank’s sludge and scum levels reach certain thresholds, it’s actually beneficial to leave the septic tank alone.

Why Your Septic Tank Looks Full After Pumping – Septic Maxx

To guarantee that your tank does not fail, you should examine it on a regular basis and get it pumped out as prescribed by the provincial codes. Septic tanks will begin to leak if they fail, and these leaks will contaminate the environment as they continue to degrade. A septic system that has failed to the point of damaging the environment will be required to be replaced by the legislation, which is quite harsh. In order to prevent this from happening, it is in your best advantage to learn about the suggested pumping schedule for your vehicle.

Water is Necessary

Pumping a septic tank removes the solid waste or sludge from the tank’s bottom, allowing it to function properly. Excessive sludge in a septic tank can find its way through the outlet and into the drain field pipes, causing severe flooding in the surrounding area. Not everyone is aware that there is a specified operating level for all septic tanks, which may be found here. 8 to 12 inches from the top of the septic tank’s lid should indicate that the tank is “full.” This might vary based on the size and kind of septic tank used.

When the water level in your tank exceeds the capacity of the pipe, your tank is considered to be overfilled.

You should get your septic system examined and water usage should be restricted until an expert can determine the source of the problem.

What Can Cause Your Septic Tank to Overfill

There might be a variety of factors contributing to your septic tank being overfilled. The presence of an overfilled septic tank is frequently a symptom that your drain field is not operating properly. The drain field is the final fixture in the septic system, and it is responsible for returning treated wastewater to the surrounding soil. When your drain field floods, the water flow becomes obstructed, causing the water level in your septic tank to increase significantly. Plumbing problems and excessive water use are two more prevalent problems.

Excessive water use might cause the septic tank to fill with more contents than it is capable of handling, resulting in a high water level.

Septic Maxx provides high-quality solutions that effectively tackle the problems that afflict septic tanks.

Get in touch with us to talk with a septic specialist right now.

Procedure for Opening Septic Tanks

ASK a question or make a comment about how to open a septic tank safely and properly for inspection or cleaning.

InspectAPedia does not allow any form of conflict of interest. The sponsors, goods, and services described on this website are not affiliated with us in any way. Instructions on how to open the septic tank. The location of the septic tank cleanout or cover, as well as the access and opening processes. We discuss some of the things to look for before opening the septic tank, such as subsidence, indications of recent work, and septic tank coverings that are not suitable to use. Then we demonstrate how to remove the septic tank lid or the access port cover from the tank.

For this topic, we also have anARTICLE INDEX available, or you may check the top or bottom of the page. Use the SEARCH BOX to discover the information you’re looking for quickly.

Procedures for Safe Opening of a Septic Tank, Cesspool, or Drywall for Inspection or Cleaning

Conflicts of interest are not tolerated at InspectAPedia.com. No affiliation exists between us and any sponsors, products, or services mentioned on this website. Instructions on how to access the septic system. Procedures for accessing and opening the septic tank cleanout or lid. We discuss some of the things to look for before opening the septic tank, such as subsidence, indications of recent work, and septic tank covers that are not safe to be opened. Afterwards, we show you how to remove the septic tank lid or access port cover.

There is an article index for this topic available as well, or you can use the page top or bottom navigation options.

How to remove the lid from a septic tank

When it comes to pumping out the septic tank, which septic tank entrance should be used? Why

In this septic tank pumpout article series, you’ll learn how to locate, open, pump out, clean, and inspect conventional septic tanks, as well as how to locate, open, pump out, clean, and inspect conventional septic tanks using photos. In addition to septic pumping tank truck operators, this guideline is meant to provide basic information to homeowners and septic service providers that are concerned about septic system maintenance.

In this septic tank pumpout article series, you’ll learn how to locate, open, pump out, clean, and inspect conventional septic tanks, as well as how to locate, open, pump out, clean, and inspect standard septic tanks using photographs and illustrations. As a general guideline, this document is designed for septic pumping tank truck operators as well as homeowners and septic service firms that are concerned about septic system maintenance.

Here is an example of a septic tank cover that was discovered atop an unstable home-made collection of concrete blocks that had been piled by the owner to serve as an access well to his septic tank. Because the masonry blocks were misaligned and loose, and because the tank aperture into which the cover opened was bigger than the cover, there was a serious collapse risk that may have resulted in a deadly hazard. We covered the area with plywood and roped it off, and we quickly informed the residents and the property owner of the situation, both verbally and in writing

Procedure for Opening the Septic Tank Pumping Access Port

It is necessary to clean the septic tank using a cleanout port, which is normally positioned in the center of the tank. A small access opening, such as one over an intake or outlet baffle, does not provide enough space for adequate sludge removal from the septic tank bottom, and it increases the likelihood of future clogging of the tank’s inlet or outlet due to partially removed floating scum that has not been completely removed from the tank bottom. In this particular scenario, we already had the measurements to the exact placement of the septic tank cleanout cover due to previous work.

A wrecking bar is set to be used to remove the cover from the vehicle.

Reader CommentsQ A

@Ron, In order for a concrete septic tank lid to be correctly erected, it must feature both access openings and cast in iron loops to which a hoist may be attached. Alternatively, if your septic tank cover does not have those points of purchase for lifting, you will require a flat bar and a larger wrecking bar to pry up the excavated lid from the septic tank sufficiently to allow you to put a chain around the lid, most likely two Chainz, and lift the lid with a hoist and tripod mechanism or you will use an on-site motorized hoist.

1/2 x 27/4 removing the top of a septic tank @Phil, Although what you describe is theoretically doable, it may be less expensive and more rational to do so in a different way.

This is due to the fact that just stitching a circular hole does not ensure that I am creating a hole through which the lid will not be dropped.
Edge My concrete septic tank, which was constructed when the home was built in 1979 and does not have any manholes or openings for pumping out, is in poor condition.
Is it feasible to cut two manholes using a concrete saw that are 20″/24″ in diameter and then build risers and a cover on top of them?

Could you please share a picture of the tank top?
It is common for the concrete top to be tapered; nevertheless, it may just be trapped by effloresent salts and filth.
I have a feeling that simply tugging will not be effective.

This would have stopped leaks but would have made it extremely difficult to open the tank for the next person who needed to open the tank.

Repeat this process many times all around the cover’s perimeter.

For me, this has worked almost every time in the past.

It is recommended that you build a septic tank riser that is sealed to the tank top, as well as a new secure cover on top of the riser if your septic tank lid is not near to the ground level.

Never work on your own.

I’ve erected two wood 4x4s on top of the lifting ring to provide additional support.

All I’ve done three times is shattered those 4x4s.

Do you have any recommendations?

A septic tank pumping provider can remove plastic bags, tiny pebbles, and other debris from your tank, as well as the sediments, scum, and sludge that has accumulated there.

What is the best way to get them out?

When the septic tank is drained out, would it make sense to place a plastic bag over the top hole of the tank to keep the odors contained?

Gerard A plastic bag as a sewer line cap doesn’t seem right to me – it’s not durable, it’s the incorrect material if a cover is required, and if it’s a vent rather than an access pipe, the vent must be open to the atmosphere and protected from animal intrusion.

What is the function of this item?

A typical septic tank is equipped with clean out access covers that are strategically placed.

Maybe something as basic as a flat piece of concrete or stone will be sufficient, or maybe something more complex.

To be quite honest, I would have expected the contractor who dug the hole to be accountable for ensuring that the system was repaired and safe.

What should I do to solve it?

What store would I go to in order to acquire septic tank covers?

A few years ago, I had a beautiful new house built for me.

I have three plastic polylok lids, one of which is above ground and is for the pump.

I’d like to purchase risers so that I may build all three at a depth of around 6 inches below ground level.

What are the advantages and disadvantages.

Do you have any other suggestions?

I apologize for the lengthy post.

Sorry, but “True Bolt” isn’t a phrase I’m familiar with or associate with septic tank lids in any way.

Although this is not always the case, Mary, as the pumper may be able to access the entire tank bottom from a single opening depending on the tank’s size and shape; however, if your pumper is unable to do so from a single opening, you may want both openings opened to inspect the condition of the tank baffles.

There are two holes in my septic tank. Is it necessary to open both doors for a pump out?

Question:cannot find the manhole cover of the septic tank

@Ron, In order for a concrete septic tank lid to be correctly erected, it must feature both access openings and cast in iron loops to which a hoist may be connected. Alternatively, if your septic tank cover does not have those points of purchase for lifting, you will require a flat bar and a larger wrecking bar to pry up the excavated lid from the septic tank sufficiently to allow you to put a chain around the lid (probably two Chainz), to lift the lid with a hoist and tripod mechanism, or you will use an on-site motorized hoist.

Half-inch by 27-quarter-inch septic tank top pushing up @Phil, Although what you describe is theoretically conceivable, it may be less expensive and more reasonable to do it in a different way, as described above.
This is due to the fact that just stitching a circular hole does not ensure that I am creating a hole through which the lid will not fall.
Edge My concrete septic tank, which was placed when the home was built in 1979 and does not have any manholes or openings for pumping out, was not designed for this.

What if I want to cut two manholes using a concrete saw that are 20″/24″ in diameter and then construct risers with a lid on top of them?
Please provide a photo of the tank top.
Are there any specific details?

The lid should be forced up using a chain hoist or a strip of horizontal timber held on one end by a post and the other by a hydraulic jack.

If someone was trying to seal the tank lid against ground water leaking when it was last installed, it’s likely that they oozed some silicone or butyl sealant over the lid edges, which would stop leaks but make it a nightmare for the next person who has to open the tank.

Repeat this process many times all around the cover.

In my experience, this method has worked nearly every time.

It is recommended that you build a septic tank riser that is sealed to the tank top, as well as a new secure cover on top of the riser, if your septic tank lid is not near to ground level.

Working alone is never a good idea.

Over the top of the lifting ring, I’ve built up two oak 4x4s.

Nothing more than breaking those 4x4s three times.

Do you have any advice?

In addition to plastic bags and tiny rocks, septic tank pumping companies may also remove the particles scum and sludge that have built up in your tank over time.

the best way to get them out of my system Gerard A plastic bag as a sewer line cap doesn’t seem right to me – it’s not durable, it’s the incorrect material if a cap is required, and if it’s a vent rather than an access pipe, the vent should be open to the atmosphere and protected from animal ingress.

Is this a good idea?

Gerard A plastic bag as a sewer line cap doesn’t seem right to me – it’s not durable, it’s the incorrect material if a cap is required, and if it’s a vent rather than an access pipe, the vent should be open to the atmosphere and protected from animal ingress.
Is this a good idea?
John, What you’re saying strikes me as a bit weird.

As a result, I’m completely baffled as to what sort of tank you’re running.
Attention: We don’t want surface water seeping into the tank, and we don’t want an unsafe cover that may cause harm or death if someone were to fall into the tank.
They cut a hole in the tank in order to pump out the contents.

Maree, The most convenient option is to locate a local septic tank provider near where you live rather than searching online.

Tom, What you’re proposing is totally acceptable in my opinion.

It was good when I had my tanks cleaned last week; the only problem was that he had to dig approximately 12 inches below ground for the lids.

I have two more in the basement.

All three of these structures will be around 6 inches below ground level, thus I would like to obtain risers for them.

What are the benefits and drawbacks of each option?

Do you have any additional ideas?

Your assistance has been greatly appreciated!

It is possible to access my septic tank from two directions. For a pump out, do both valves have to be opened?

Reply:

If it’s a cesspool, rather than a septic tank, and it’s spherical, the access lid is normally located in the center of the container.

Question: how do i remove septic tank lid that is stuck

The entrance lid would normally be in the center of the cesspool, if it is in fact a cesspool rather than a septic tank, and it is spherical.

Reply:

Anon:WARNING: If the septic tank cover, lid, or access aperture has partially caved in or sank into the tank, the condition is extremely dangerous – an unsecure cover implies that someone might fall into the tank, which is generally lethal very quickly. Please keep everyone away from the septic tank area until such time as you have had the tank inspected and opened for additional inspection by a professional. Depending on the tank type and condition, lifting the lid may necessitate the use of a pry bar or wrecking bar, as well as a small portable winch (which is unusual).

Alternatively, consider the following:

Septic Pumping ProcedurePumper Truck Operation Articles

PROCEDURE FOR INSPECTING SEPTIC TANKS
MISTAKES MADE IN THE PUMPING OF SEPTIC TANKS

PROCEDURE FOR PUMPING SEPTIC TANKS

HOW TO CLEAN A SEPTIC TANK
WHEN TO CLEAN A SEPTIC TANK

WHEN NOT TO PUMP A SEPTIC TANK
HOW TO FIND A SEPTIC TANK
HOW TO OPEN A SEPTIC TANK

INSPECT THE SEPTIC TANK BEFORE PUMPING
SEPTIC TANK INSPECTION PROCEDURE
SEPTIC TANK LEVELS OF SEWAGE

PUMPER TRU

Suggested citation for this web page

CLEANING SEPTIC TANKS; WHEN TO CLEAN THE SEPTIC TANK; WHEN NOT TO PUMP A SEPTIC TANK; HOW TO FIND THE SEPTIC TANK; HOW TO OPEN A SEPTIC TANK; INSPECT THE SEPTIC TANK BEFORE PUMPING; SEPTIC TANK INSPECTION PROCEDURE; SEPTIC TANK LEVELS OF SEWAGE; PUMPER TRUCK O

INDEX to RELATED ARTICLES:ARTICLE INDEX to SEPTIC SYSTEMS

Alternatives include asking a question or searching InspectApedia using the SEARCH BOXfound below.

Ask a Question or Search InspectApedia

We encourage you to use the search box just below, or if you prefer, you may make a question or remark in theCommentsbox below and we will get back to you as soon as possible. InspectApedia is a website that allows you to search for things. Please keep in mind that the publication of your remark below may be delayed if it contains an image, a web link, or text that seems to the program to be a web link. Your submission will appear when it has been reviewed by a moderator. We sincerely apologize for the inconvenience.

Technical ReviewersReferences

Please use the search box just below, or, if you prefer, you may make a question or remark in theCommentsbox below and we will react as soon as we can. Thanks for visiting! InspectApedia is a website that allows you to search for information. Please keep in mind that the publication of your Comment below may be delayed if it contains an image, a web link, or text that seems to the program to be a web link. Your posting will appear when it has been reviewed by a moderator. Excuse the delay in getting back to you!

How to Find the Lid on a Septic System

All septic tanks eventually fill with sediments and must be pumped out on a regular basis in order to remain in excellent functioning order. If the tank’s lid is not on a riser at ground level and you are not the home’s original owner, you may be unable to determine where the lid is located.

A typical septic tank is 4 inches to 4 feet underground, with all of its components, including the cover, buried between 4 inches and 4 feet underneath. This is true regardless of whether the septic tank is equipped with special risers that keep the lid flush with the surface of the ground.

Consult A Map

First, choose with the most straightforward choice. The installation of septic tanks at all locations is recorded in most counties’ permission records, which are kept on file for future reference. Typically, this will include a schematic indicating the placement of the tank on the land, as well as certain dimensions that will allow you to measure to the precise site of the tank. If your tank was placed before your county made it a requirement to record the location of such tanks, you may find yourself with nothing to show for your efforts.

Search For A Sign

Septic tanks are placed in such a way that they are as unnoticeable as possible on the land. After the grass has grown back after installation and some time has passed, it is possible that just a few visual indications will remain. Pay particular attention to the contours of your yard for any inexplicable high or low points that might suggest the presence of an underground storage tank.

Follow The Pipe

Installation of the septic tank takes place along the sewage line that runs from the house into the front yard. Locate the 4-inch sewage pipe at the point where it exits the home in the basement or crawl space, if it is there. Locate the same spot outside and make a note of it. Insert a thin metal probe into the earth, identify the 4-inch sewage line, and follow it across the yard, probing every 2 feet, until you reach the end of the property. Septic tanks are required to be at least 5 feet apart from the home in all states except Alaska.

Whenever the probe makes contact with flat concrete, fiberglass, or polyethylene it indicates that the tank has been located.

Locate The Lid

The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Investigate the tank’s circumference to determine its boundaries and outline the rectangle’s boundary using a pencil. A septic tank that was built before 1975 will have a single concrete lid that is 24 inches in diameter in the center of the rectangle. If the tank was built after 1975, it will have two covers made of fiberglass or polyethylene, centered at the ends of the rectangle and centered at the ends of the rectangle.

Call A Professional

Opening a septic tank is a job best left to the pros once the lid has been discovered. Concrete septic tank lids are extremely heavy, and many require the use of lifting tools to remove them completely. An open tank has the potential to release toxic gases. Anyone going around on the property who comes into contact with an exposed septic tank might be in risk. Because of the noxious vapors present in an open tank, falling into one can be lethal.

Mark The Spot

Make a note on the ground near where the tank was pumped by a professional and the lid was buried to serve as a reference in the future.

In order to keep track of where you are, you should choose a hefty circular patio tile that is embedded in the ground. Additionally, draw your own map of the area and store it with your other important papers.

Does a septic tank have two lids?

In most cases, there are two lids that allow you to access your septic tank. Asked in category: GeneralLast updated: 1st July, 2020 If your septic tank was erected before 1975, it will feature a single 24-inch concrete lid in the center of the rectangle, which must be left open when pumping out your septic tank. Atwo -compartmenttankinstalled after 1975 willhave two lidsof either fiberglass or polyethylene, located at opposing ends of the rectangle.Also,can a septic tank have only one lid? Installation of a Pressure Distribution System – This tank will only have one mainlid, which will be located in the center of the tank.

Similarly, one may wonder how far apart the two lids of a septic tank are located.
What is the diameter of thelidson thetank?

The answer is between 20 and 24 inches.
Septic tanks are generally rectangular in shape and measure roughly 5 feet by 8 feet in size.

Help! My Septic Tank is Full!

Posted on a regular basis We receive a lot of calls concerning septic tanks that are “full.” But what does the term “full” truly imply? A septic tank should always be “filled” to its normal liquid level, which is the level at which the effluent exits the tank and flows to the absorption area, according to the manufacturer. On average, this typical liquid level is between 8″ and 12″ below the tank’s maximum capacity, depending on the model (see picture at right). If the liquid level is near the bottom of the outflow pipe, it is reasonable to believe that the absorption area is receiving the wastewater generated by the home.

If the tank is overflowing, it is typically a sign that there is a problem with the absorption area.

Plumbing or septic issue?

We get a lot of calls from folks who want us to pump their tank because they claim it is full.usually because they are experiencing troubles. However, there are situations when the plumbing is the source of the problem. What is the best way to determine if an issue can be resolved by your septic maintenance provider or a professional plumber?

Check the cleanout

If the problem is caused by backup in the house, we recommend that you check your cleanout between the house and the tank (if one is present and accessible) to see if there is any backup in the cleanout (which is typically a 4″ PVC pipe with a removable cap). If the problem is caused by backup in the house, we recommend that you check your cleanout between the house and the tank (if one is present and accessible) to see if there is any backup in the cleanout. If the cleanout does not contain any backlog, then we normally recommend consulting a plumber, since this implies the wastewater from the residence is not making it to the cleanout.

Afterwards, you may check to see if the liquid level in the septic tank is normal or excessive by removing the lid(s) of the tank and looking inside.

If it is overflowing, you may be dealing with more serious problems (i.e.

Till you have a cleanout, your odds of requiring the services of either a plumber or a septic firm are 50/50, and you won’t know unless one of the two comes out to inspect the situation for you.

If you are able to see straight into your tank to gauge the quantity of liquid in it, this might assist you in determining which service provider to call for assistance.

Check for smells

If the problem is caused by backup in the house, we recommend that you check the cleanout between the house and the tank (if one is present and accessible) to see if there is any backup in the cleanout (which is typically a 4″ PVC pipe with a removable cap). If the problem is caused by backup in the house, we recommend that you check the cleanout between the house and the tank (if one is present and accessible) to see if there is any backup in the cleanout. If there is no backup in the cleanout, we normally recommend that you call a plumber since this implies that the wastewater from the home is not making it to the cleanout.

This may then be established by removing the lid(s) of the septic tank and looking to see if the liquid level is normal or excessively high in the tank.
There may be more serious problems if the container is overflowing (i.e.
Till you have a cleanout, your odds of requiring the services of either a plumber or a septic firm are 50/50, and you won’t know unless one of the two comes out to inspect the situation.
This will assist you in determining which service business to call for assistance.

Signs of a larger problem

After being drained out, a septic tank would normally refill to its regular liquid level within a few days to a week, depending on the size of the tank and the number of people living in the property. As soon as the tank has been refilled to its usual liquid level, effluent can begin to flow back into the absorption area again. If the septic tank is “overfull” this may be a sign of a larger problem with the system (see picture at right) (see picture at right). If you are experiencing this problem, draining out your septic tank may provide some temporary respite, but it is unlikely to provide long-term relief.

Over the course of 80 years, Van Delden Wastewater Systems has proven itself to be the premier Wastewater System provider, supplying San Antonio, Boerne, and the surrounding Texas Hill Country with services you can rely on today and in the future.

What you should expect when your septic tank needs pumping

A septic tank will normally refill to its regular liquid level within a few days to a week after it has been drained out, depending on the size of the tank and the number of people living in the property. As soon as the tank has been refilled to its usual liquid level, effluent can begin to flow back into the absorption region. The fact that the septic tank is “overfull” may indicate a more serious problem with the entire system (see picture at right). A temporary solution such as pumping out the septic tank will usually suffice in this situation; however, it is unlikely to provide long-term solutions.

Over the course of 80 years, Van Delden Wastewater Systems has proven itself to be the premier Wastewater System provider, supplying San Antonio, Boerne, and the neighboring Texas Hill Country with services you can rely on today and in the future.

We can assist you with any of your wastewater system needs, and our specialists can also assist you with your septic installation and maintenance needs: 210.698.2000 (San Antonio) or 830.249.4000 (Austin) (Boerne).

Choosing a certified pumper

We recommend that you identify your septic tank before contacting a pumping company. Here is a list of questions you should ask the pumper about their services that we recommend you ask:

What is the approximate cost of the pump-out
And Will additional gallons be charged if the septic tank has a capacity more than 1,000 gallons? Is it included in this price the expense of excavating to expose the septic tank lid(s)
If not, do you charge by the foot or by the meter? How much do you charge to dig you out if you don’t have one
Is there a charge for dumping fees included? Was it determined that this fee includes a visual check of the septic tank’s entrance and exit baffles? Do you charge an additional fee for cleaning the filter baffle? If a tank has not been properly maintained, is there an additional price for the additional water and time necessary to pump it out? (for example, pumped on a regular basis)
Please specify the distance and elevation to where the Pumper’s vehicle will be stationed if you have a long distance to pump or if you will be pumping up a steep hill (for example, in your driveway or in the yard). The Pumper will decide whether or not the vehicle is capable of providing this sort of service. Is pumping the pump tank a frequent component of your routine maintenance? What is the cost of providing this service? It is recommended that a pump tank be pumped in addition to the septic tank, cleaned with water, and then dried with a blow dryer. If the pump tank is quite full, you may be charged an additional price

Locating the septic tank

Once you’ve decided on a Pumper, you’ll need to locate the septic tank on your property. Most Pumpers will charge you for the time it takes to locate the tank and open the septic tank lid (s). You can perform the necessary work to expose the septic tank lid(s) prior to the arrival of the Pumper. Ohio Public Health – recommends that you have “risers” installed to make septic tank pumping and inspection visits easier and less time-consuming for the Pumper and for you. With locking gas tight lids linked to both the tank and the riser and access raised to the surface, there is no digging required every time the septic tank needs to be pumped.

It is likely that the majority of septic system Pumpers will be able to assist you.
Both compartments must be examined and pumped in order to meet the requirements.
If your septic system is equipped with an as-built (a map of your septic system), identifying the septic tank will be straightforward.
The following talents will be required by you or your Pumper if an as-built is not available: investigation

If there is a crawl space, you may be able to locate the tank by determining where the plumbing exits the foundation wall and then using a probing bar to locate it. If you have a fiberglass or polyethylene tank, a probe bar is not suggested unless extreme caution is exercised when using the probe bar. Testing will only be effective if the tank is not more than 1 to 2 feet below the surface of the water. If no crawl space is available you can sometimes go by where the plumbing vents are located in the roof. A person who is walking behind the home and coming from a restroom can find themselves at the exit point of the sewage line that connects to the septic tank

Using an electronic detecting equipment may be essential if none of the above mentioned approaches prove successful. Some rental services contain a transmitter that may be flushed down the toilet and is detected by a receiving unit, which can be found in some rental services. In certain cases, drainfield location is the specialty of septic system contractors. See a list of septic system installers who are certified. As long as the tank is exposed, sketch a map depicting the location of the septic tank lid(s) in relation to the home and make a copy of the map for your records.

Pumping the septic tank

Before the Pumper begins the process of pumping out the tank, you may request that he measure the thickness of the scum and sludge layer layers on the inside of the tank. Using this method, you can determine the pace at which the particles collect in the tank, which will assist you in determining when it is necessary to have the septic tank pumped again. Pumping frequency will be in the range of 2 to 3 years for the vast majority of families. It doesn’t matter how often you pump your septic system; frequent inspections will provide you peace of mind that everything is in working order inside those tanks.

Concerning the inspection of your septic system. The septic tank Pumper should present you with a receipt that details the services that were done to your tank. This receipt should contain the following information:

The company’s name, address, and phone number
Pumper’s certification number
Number of gallons that were pumped in an approximate manner the number of compartments that have been pumped In good working order, the tank baffles In-tact condition of the septic tank
Provide specifics on any work performed on baffles or access lids. This information should be included on the pump receipt if the scum and sludge layers were measured. Any work done on the septic tank or pump tank should be documented. Any additional service work that is completed

Proper Access Opening for Septic Tank Pumping

Pumping of the septic tank must take place through the septic tank lid openings in order to be effective. The only method to completely remove all of the waste from the tank is to thoroughly agitate the tank, which will remove both the water and the solids that have accumulated inside the tank. This is done in order to eliminate anything and everything from the tank! If someone is pumping through a clean-out or inspection port, they are not conducting a full cleaning job, according to industry standards.

Pumping vs. Cleaning Your Septic Tank

Pumping of the septic tank must take place through the septic tank lid ports in order for the tank to function properly. A full extraction of all waste from a tank can only be accomplished by stirring the tank sufficiently to remove both water and solids contained inside it. This is done in order to eliminate everything and everything from the tank. If someone is pumping through a clean-out or inspection port, they are not performing a comprehensive cleaning procedure, according to the manufacturer.

How Many Lids Does My Septic Tank Have?

Most of the time, these lids are situated beneath the surface of the earth, and excavation is necessary to discover and expose those lids. Some tanks will only have one lid opening, while others will have two or three. How do you know what you have in your tank? The answer to this question is based on the year in which your septic tank was installed. From 1960 to 1970, the coffin lid was the most common type of lid. This will need further excavation in order to move the lid and pump. 1970s through the 1990s*: These septic tanks are normally one-compartment tanks with a manhole in the center that is 18 inches in diameter.

Years 2000–present: These tanks MIGHT additionally include a filter in the back chamber that has to be cleaned.

What If My Septic Tank Has Risers?

Septic tank “risers” come in a variety of shapes and sizes. The correct risers from which we may pump are composed of a polymer or concrete, depending on the use. Their mounting will be done immediately on the lids of the septic tanks, which is a good idea. The green and brown lids in the illustration above are the correct pumping ports. Because we will have to excavate and expose the septic tank lids if you do not have these types of risers, we will be forced to pump your septic tank. Many people do not want to disturb the grass in the surrounding region, but it must be done anyway!

Do you want to add Septic Tank Risers to your existing septic system?
Riser installation is something we do for you.
The cost of the risers is generally recouped within a couple of pumping operations, and the access is now at grade, making regular maintenance servicing and filter cleaning easier, especially if you have a more recent system installed.
Contact us now.
We will be delighted to answer any issues you may have or to provide any clarification you require.

It is more than a pump job when you hire Priority Pumping as your contractor! We like educating our customers about their systems and assisting them in developing a good maintenance plan that will keep their systems happy and healthy for years to come.

Common Septic Tank Facts

Septic systems are a low-cost and frequently successful alternative to conventional sewer systems. Concrete tanks have been the most frequent since the 1940s, with 3 – 500lids for a 1000 gallon tank and 4 – 500lids for a 1500 gallon tank being the most typical. Tanks began to be equipped with 16″ square concrete plugs with a lifting bail in the late 1990s, allowing for easier access to both sides of the tank. Many tanks today are made of fiberglass or plastic. Over time, the concrete might degrade, and the lids may develop cracks or possibly shatter completely due to the pressure.

Even broken lids should be replaced for the sake of the public’s safety.
They give access to your septic tank by removing 20” green covers.
This is done in order to prevent anyone, especially children, from removing a lid and falling into the container.
A typical water level for a tank should be 6″ below the top of the tank, and the tank should be kept completely filled at all times.
The level of the water is often a good sign of potential problems.
Additionally, it might suggest a clogged intake line, which could be caused by roots, a damaged pipe, or a loose joint.
If there has been a lot of rain, the earth may get saturated, making it impossible for any additional water to seep through the soil to the surface.
If your tank has allowed particles to enter the field lines, this might cause the openings in the corrugated pipe to get clogged, preventing water from percolating through the soil as effectively as it should be.
An output filter may be placed to prevent particulates from entering the field lines, but it would need to be cleaned on an annual basis to ensure that this does not happen.

How Your Septic System Works

Underground wastewater treatment facilities, known as septic systems, are often employed in rural regions where there are no centralized sewage lines. They clean wastewater from residential plumbing, such as that produced by bathrooms, kitchen drains, and laundry, by combining natural processes with well-established technology. A conventional septic system is comprised of two components: a septic tank and a drainfield, often known as a soil absorption field. It is the septic tank’s job to decompose organic matter and to remove floatable stuff (such as oils and grease) and solids from wastewater.

Alternate treatment systems rely on pumps or gravity to assist septic tank effluent in trickling through a variety of media such as sand, organic matter (e.g., peat and sawdust), constructed wetlands, or other media to remove or neutralize pollutants such as pathogens that cause disease, nitrogen, phosphorus, and other contaminants.

Prior to discharging wastewater into the environment, several alternative systems are designed to evaporate or disinfect the effluent.

Specifically, this is how a typical conventional septic system works:

All of the water that leaves your home drains down a single main drainage pipe and into a septic tank. An underground, water-tight container, often composed of concrete, fiberglass, or polyethylene, serves as a septic system’s holding tank. Its function is to retain wastewater for a long enough period of time to allow particles to sink to the bottom and form sludge, while oil and grease float to the surface and produce scum. Sludge and scum are prevented from exiting the tank and moving into the drainfield region by compartments and a T-shaped outlet. After that, the liquid wastewater (effluent) exits the tank and flows into the drainfield. The drainfield is a shallow, covered hole dug in unsaturated soil that serves as a drainage system. Porous surfaces are used to release pretreated wastewater because they allow the wastewater to pass through the soil and into the groundwater. In the process of percolating through the soil, wastewater is accepted, treated, and dispersed by the soil, finally discharging into groundwater. Finally, if the drainfield becomes overburdened with too much liquid, it can flood, causing sewage to flow to the ground surface or resulting in toilet backups and sink backups. Finally, wastewater percolates into the soil, where it is naturally removed of harmful coliform bacteria, viruses, and nutrients. Coliform bacteria are a kind of bacteria that may be found in the intestines of humans and other warm-blooded animals, with humans being the most common host. As a result of human fecal contamination, it is a sign of this.

The Guadalupe-Blanco River Authority has built an animated, interactive model of how a residential septic system works, which you can view here.

Do you have a septic system?

It’s possible that you’re already aware that you have a septic system. If you are not sure, here are some tell-tale symptoms that you most likely are:

You make use of well water. In your home, the water pipe that brings water into the house does not have a meter. In the case of a water bill or a property tax bill, you will see “$0.00 Sewer Amount Charged.” It is possible that your neighbors have a septic system

How to find your septic system

You can locate your septic system once you have confirmed that you have one by following these steps:

Taking a look at the “as constructed” drawing of your house
Making a visual inspection of your yard for lids and manhole covers
Getting in touch with a septic system service provider for assistance in locating it

Failure symptoms: Mind the signs!

A bad odor is not necessarily the first indicator of a septic system that is failing to work properly. Any of the following signs should prompt you to seek expert assistance:

Water backing up into the drains of homes and businesses
It is especially noticeable in dry weather that the drainfield grass is bright green and spongy. The presence of standing water or muddy soil near your septic system or in your basement
A strong stench emanating from the area surrounding the septic tank and drainfield

Septic Tank Cleaning

Water backing up into the drains of homes and businesses. It is most noticeable in dry times when the drainfield is lush and green. The presence of standing water or muddy soil near your septic system or in your basement. A strong stench emanating from the area surrounding the septic tank and drainfield; and

Locating and Exposing Septic Tank Lid(s)

Some septic lids are more difficult to locate than others. If this is the case with your septic system, our service technicians will find it with the use of the appropriate equipment. Using a shovel or an excavator, we’ll uncover your septic lids once they’ve been located and exposed. Lids may break from time to time due to corrosion or a fault in the structural integrity of the container. Our service technicians will be able to simply replace them in this situation. You should keep in mind that whether or not you have one or two lids is determined by the age of your system.

Cleaning the Tank

It is essential that all liquid and compacted sludge or solid waste from a septic tank be removed from the tank in order to perform an effective septic tank cleaning. To achieve this, we adopt a method called backflushing. It is important to backflush to guarantee that even the most obstinate build-up is cleared. After that, the walls of your tank are sprayed down with new water, which thoroughly cleans the entire system.

Post-Clean Inspection

After your tank has been cleaned, our specialist will inspect the interior of your tank and tell you if there are any symptoms of structural damage that may need to be repaired. Septic tank cleanings should be performed on average every two to three years to minimize the need for costly repairs or replacements. If you would like to book your service or receive a quotation for your next septic tank cleaning, contact the professionals at Forever Clean today!

Call on Us for All of Your Raleigh, NC Septic Tank Cleaning Needs!

That is why we are regarded as professionals in our field of expertise. Septic tank cleaning is a process that we take very seriously. We strive to complete your project as quickly as possible while minimizing the impact on your landscaping, and we keep you informed throughout the process.

Forever Clean’s many repeat clients rely on us for their routine septic tank cleaning because of the results we produce and the continuously smooth, hassle-free process that we provide on a constant basis. We complete the task quickly and efficiently, causing you no trouble or concern.

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

3.
Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
When you do, that’s when your septic tank comes into play!
Look for the Lid.
You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
Those areas should be excavated in order to disclose the lids.
Get in touch with the pros.
Lifting concrete lids will necessitate the use of specialized equipment.
A fall into an unprotected septic tank has the potential to be lethal.
Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

3 THINGS TO KNOW ABOUT SEPTIC TANK BAFFLES

By Admin on November 12, 2020 Your efforts to live as environmentally conscious as possible, as a responsible homeowner, are likely already underway, with practices such as recycling, composting, and purchasing energy-efficient equipment among your list of accomplishments. As a septic tank owner, you want to be sure that anything you put into your tank and septic field is causing the least amount of ground contamination as is reasonably practicable. Fortunately, there are a number of modest improvements you can do immediately to make your septic system even more ecologically friendly than it already is.

Have your septic tank inspected and pumped on a regular basis.
A bigger septic tank with only a couple of people living in your house, for example, will not require pumping as frequently as a smaller septic tank or as a septic tank that must manage the waste products of multiple family members will require.
When in doubt about how often to pump your septic tank, consult with a professional for advice.
In addition to locating and repairing any damage, a professional can ensure that the septic field is in good working order and that your septic tank is functional, large enough to handle your family’s waste, and not causing any unwanted pollution in nearby ground water.
Avoid flushing non-biodegradable items down the toilet or down the toilet.
Items that are not biodegradable are unable to properly decompose in the septic tank and might cause the system to get clogged.
In addition to causing issues in your house, septic system backups can damage ground water in the area surrounding your septic field.

Towels made of paper Products for feminine hygiene Grease or fats are used in cooking.

grinds from a cup of coffee Even if you have a trash disposal, the food scraps that you flush down the drain and bring into your septic system may cause unanticipated harm to your plumbing system.

Food scraps can enhance the amounts of nitrogen and phosphorus in the wastewater, which can disturb the natural bacterial balance of the septic tank, among other things.

Water conservation should be practiced.

Exceedingly large amounts of water use will interfere with the normal flow of wastewater from your home into your septic tank.

Limiting the amount of time you spend in the shower and turning off the faucet while brushing your teeth, as well as purchasing a smaller dishwasher and washing machine that use less water, are all simple strategies to reduce water use in your home.

The following are some basic steps you can take to make your septic system more ecologically friendly: save water, maintain your septic system and tank, and recycle wastewater. To get answers to any of your septic tank-related issues, get in touch with the experts at Upstate Septic Tank, LLC.

Everything You Need To Know About Your Septic System

Florida people rely on roughly 2.6 million septic systems to dispose of waste and wastewater on a daily basis, accounting for 30% of the state’s population. Homes and businesses in rural areas rely on these systems to dispose of waste in an efficient and environmentally friendly manner.

What Are Septic Tanks Made From?

Septic tanks are a waterproof box composed of concrete, fiberglass, or polyethylene material that is used to dispose of sewage. In other words, there will be no debris, dirt, or water from the surrounding ground that may get into the tank. Septic tanks made of concrete and/or fiberglass are the most common types.

Common Styles Of Septic Tanks

ATUs employ three compartments — a garbage compartment, aeration chamber, and clarifying compartment — to treat and filter waste. An aerobic, or well oxygenated, environment is created in the effluent by forcing compressed air through it. Because the bacteria thrive in this environment, waste decomposes more quickly than it would in a conventional septic tank. This helps to limit the quantity of organic material that enters the soil and groundwater around the house.

Double Compartment

Most tanks built since 1976 have two compartments for filtering effluent, solids, and wastewater that enters the tank during the construction process. The first compartment, which is placed adjacent to the intake pipe, is often bigger than the second compartment, which is located further away. It is possible to see the liquid flowing from the first compartment into the second compartment. Before the effluent is discharged into the outflow pipe, any remaining sludge and scum separate from the liquid.

Pump Tank

The quantity of wastewater that flows from the septic tank is controlled by a pump tank. Pump tank level increases as effluent accumulates in the tank and eventually reaches the level set by a control float. As soon as the float is activated, the pump starts pumping effluent into the drain field in a predefined volume.

Holding Tank

The quantity of wastewater that flows out of the septic tank is controlled by a pump tank. Pump tank level rises as effluent accumulates in the tank and eventually reaches the level controlled by a floating float. A predefined volume of effluent is discharged into the drain field when the float is activated.

Single Compartment

A single compartment tank was utilized in the majority of septic systems constructed before to 1976. These tanks could hold up to 1,000 gallons of liquid at a time. After entering the tank and separating into three levels, liquid waste is discharged into the septic drain field via the outflow line.

What Is FOG?

Fats, oils, and grease (also known as FOG) are frequent cooking byproducts that occur naturally in a wide variety of foods and other items. While FOG is typically viscous when it enters the septic tank, it cools swiftly as it intermingles with wastewater. However, because of its viscosity, FOG coats and covers every surface it comes into contact with when it solidifies.

How A Septic Tank Works

Solids sink to the bottom of the tank’s intake pipe, while FOG rises to the surface of the wastewater and collects at the top of the tank’s intake pipe. In most cases, the tank is large enough to keep wastewater for an extended period of time, allowing effulent separation to take place. There are three levels within the tank as a result of this separation: a sludge layer on the bottom, a wastewater layer in the middle, and a scum layer on top. bacteria, enzymes, and other microorganisms often present in human waste begin to break down the sludge layer and break down the sludge layer further.

Upon entry into the septic tank and drain field, two baffles direct and filter the water. The intake baffle prevents the scum layer from obstructing the inflow pipe, while the outflow baffle keeps scum and particles in the tank until they are removed by the drain.

What Are Septic Tank Solids?

The majority of solids contained in a septic tank may be divided into three categories:

Non-biodegradable organic solids include pet litter, plastics, and other items that do not decompose over time
Biodegradable organic solids include vegetable scraps and other cellulosic compounds, as well as toilet paper
And biodegradable organic solids include solid human feces.

Septic System Drain Fields

After leaving the septic tank, effluent goes into a drain field, which is a network of underground pipes and dirt that collects the waste. Other popular phrases include absorption field, leach field, and trench. The size of the space required is determined by the following factors:

Soil type
Seasonal variations in groundwater level
Amount of water absorbed each day
And soil percolation rate are all factors to consider.

The soil percolation rate is defined as the amount of water that the soil can absorb in one minute per inch of soil thickness. Because Florida has a high water table, the percolation rate is a significant element in selecting the site of the septic drain field.

How A Drain Field Works

An underground network of perforated pipes may be found in this location, which can be found in either several trenches or a gravel-lined soil bed. Drainage from the pipes filters through the gravel and dirt before entering the sewer system. Compaction of the soil has a significant impact on its function, which is why it is critical not to construct structures on it or drive or park vehicles of any size over it.

Why Is A Drain Field Important?

Natural filtration is provided for effluent, which is recycled back into the groundwater source. It is possible that biological and chemical pollutants may infiltrate the water and create health problems for anybody who consumed or came into touch with the water without this filtering system in place.

How To Find Your Septic TankSeptic Drain Field

It serves as a natural filter for wastewater, which is then recycled back into the groundwater supply system. It is possible that biological and chemical pollutants might infiltrate the water and create health problems for anyone who consume or come into touch with the water without this filtering system in place.

The Septic Tank Pumping Process

In order to prepare for extraction, the floating scum layer is first broken up by alternately sucking out liquid from the tank and pumping it back in to break up the bottom solid layer. Pumping is accomplished through the two access ports, which are referred to as manholes. The tank should never be pumped through the inspection ports on the baffle wall. This can not only cause damage to the baffles, but it can also result in insufficient waste removal from the tank. Until the septic tank is completely depleted, industrial vacuums are used to remove waste from the tank and into our tanker truck.

How Often A Septic Tank Should Be Pumped?

In most cases, every three to five years is sufficient. However, depending on the size of your septic tank and the amount of sediments and wastewater you produce on a daily basis, you may need to contact a septic tank pumping firm such as Jones PlumbingSeptic Tank Service sooner rather than later.

What To Expect During A Septic Tank Pumping

Before starting the pumping process, it is necessary to measure the thickness of the scum and sludge. This information is important in determining the pace at which waste accumulates and in determining when the next pumping should be scheduled. The pumping process is monitored closely by our technicians, who are actively looking for any potential system problems, such as backflow from the outflow pipe.

Backflow that is significant typically indicates a backup in the drainfield, whereas slight backflow indicates a weaker outflow line in most cases. As soon as the septic tank is completely depleted, it is ready for cleaning, and the waste is transported to a state-approved disposal facility.

Septic Tank Cleaning

Septic tank cleaning and septic tank pumping are not the same thing, despite the fact that many people use the phrases interchangeably. The removal of liquid and uncompressed solids is accomplished through pumping, whereas the removal of remaining solids is accomplished through cleaning, which includes washing the inside of the tank. Once the liquid layer has been removed from the tank, our technicians use pressurized streams of water to break up any remaining solids. Solids are removed from the tank with the use of an industrial-grade vacuum and a connected hose before the inside of the tank is washed.

This can result in the formation of sinkholes or the breakdown of the entire system.

How Often Should A Septic Tank Be Cleaned?

With every septic tank pump out, there is a new beginning. Keep in mind that the frequency with which the tank is pumped is determined by the number of people who are using the system and the volume of wastewater created on a daily basis. You may work with an aseptic tank pumping firm, such as Jones PlumbingSeptic Tank Service, to establish a regular pumping and cleaning program for your tank.

How To Keep A Septic Tank In Good Condition Between Cleanings

The most effective strategy to ensure that your septic tank remains in good working order for many years is to be informed of what can and cannot be put into the system.

Don’t DisposeFlush Items At-Will

In order to degrade materials that enter the tank, a septic system relies on bacteria that are found in nature. Although it is a mutually beneficial connection, it is susceptible to being pushed out of balance depending on the materials that are disposed of. Fat, oil, and grease (FOG); chemicals, paints, fuels, and/or motor oils; disposable diapers, sanitary, and personal hygiene products; coffee grounds; egg and nut shells; and disposable diapers, sanitary, and personal hygiene products are all common household items that should never be flushed down the toilet.

Schedule Annual Inspections

In order to digest sediments that enter the tank, a septic system must rely on naturally existing bacteria. Although it is a mutually beneficial connection, it is susceptible to being thrown out of balance depending on the materials that are thrown away. Among the typical household objects that should never be flushed down the toilet are: fat, oil, and grease (FOG); chemicals, paints, gasoline, and/or motor oils; disposable diapers, sanitary, and personal hygiene products; coffee grounds; egg shells; and nut shells.

PumpClean The Tank As Necessary

Skipping regular septic tank services is a surefire way to end yourself in a situation that might have been avoided. Performing routine pumping and cleaning allows our personnel to check the overall health of the system and correct any issues that may arise before they become a major concern.

Keep Records Of Septic LocationService

It is essential to understand the location of the entire system in order to properly maintain it. Parking or driving cars over any portion of the septic system should be avoided at all costs. The weight of vehicles can cause the system to collapse.

When this occurs, the only option for repair is a complete replacement. It is also recommended by Jones PlumbingSeptic Tank Service that you preserve records of when the system was examined, pumped, and cleaned for your own records and in case you decide to sell your home in the future.

Conserve Water

The volume of water entering a septic system has a greater influence on the health of the system than the amount of solids created by the system. The greater the volume of water that flows through the drain field, the shorter the functional lifespan of the drain field and the overall system. An excessive amount of water flow impairs effective separation of particles inside the tank, increasing the likelihood of clogged intake and outflow pipes, which can result in sewage backups in the tank.

Septic Tank Repair In Gainesville, FL

Too much water in the septic tank increases the likelihood of sediments being transferred into the pipes, which might result in a clogged system.

Aggressive Tree Roots

Tree roots are well-known for generating problems with septic tanks and systems. Many species of tree roots are stronger than septic tanks, and they can cause leaks and other structural damage by cracking the pipes and tank.

Common Septic Tank Repairs

There are a variety of reasons why the pipes might fail, including compacted and/or moving soil. Once the pipes burst, they must be fixed as soon as possible to avoid significant drainage problems. When it comes to reaching and repairing the pipes, excavation of the area is frequently necessary.

Broken Baffles

The baffles of a septic tank are responsible for keeping sediments contained within the tank. Rust or contact with sulfuric acid are the most common causes of damage. It is quite beneficial to have an annual septic check performed in order to see if there are any difficulties with the baffles before a problem occurs.

How To Prevent A Septic Tank Failure

The fact is that septic systems are not foolproof and that they benefit immensely from routine maintenance and upkeep. The majority of failures may be avoided by paying attention to what goes into the plumbing and septic lines.

Only Flush Toilet Paper

As a rule, toilet paper degrades and disintegrates more quickly than other types of paper goods. Particularly problematic are paper towels and wet wipes, which are two of the most prevalent causes of septic tank clogging and premature tank cleanouts.

Never Pour FOG Down The Drain

FOG is extremely harmful to all plumbing systems, including the septic system. FOG, when it is in liquid form, readily flows into the septic tank and collects in the top scum layer of the tank. This may not appear to be a problem, but the mixture has the potential to run into the drain field, where it might cause contamination concerns with groundwater and the surrounding soil if allowed to do so.

Regular Drain Cleaning

The numerous commercial drain cleaners available may temporarily unclog a clogged drain and associated plumbing, but they do so at the expense of the septic system’s ability to function properly. They include chemicals that swiftly eliminate the bacteria that are important for the decomposition of particles within the septic tank once they are applied. The layer of solids accumulates quickly — and needlessly — on the surface of the water. As an alternative, call a plumber to do expert drain cleaning.

How To Tell When You Need A New Septic System

A septic system may last anywhere from 20 to 40 years if it is maintained properly and repaired when needed on time.

However, if you detect any of these frequent indicators of a failing septic system, it’s time to call Jones PlumbingSeptic Tank Service to have a new septic system installed in your home or commercial property. Common signals the present system needs to be changed are:

Sinks and toilets that take a long time to drain
Plumbing that is always backed up
Sewage odors in the company, house, or yard
Patchy mushy, swampy, or damp areas of the yard Gray water that has accumulated
And grass that has grown more swiftly and is a darker shade of green

What To Know Before A Septic Tank Is Installed

In order to prevent the contamination of water sources and the creation of public health hazards that can result from incorrectly designed septic systems, the state of Florida and local municipalities have established rules and regulations to guide new septic system installations.

Required Applications, FeesPermits

The Environmental Health Service of the Florida Department of Health (FDOH) in Alachua County is responsible for issuing the necessary applications and permits. Before a permit may be issued, the house or business owner must submit a completed application, as well as a site plan, a building floor plan, and any applicable application costs to the local building department. A site evaluation is also necessary, which analyzes the overall condition of the land, as well as the soil type. Total fees are determined on the kind of septic system installed as well as the services provided by the county health division.

Minimum Tank Size

A minimum 900-gallon capacity is required for all septic tanks in Florida; however, this capacity requirement rises based on the size of the occupancy and whether the system is intended for residential or commercial usage. The specialists at Jones PlumbingSeptic Tank Service can assist you in determining the right tank size that complies with local and state specifications.

Landscaping Changes

Because septic systems are installed underground, it is probable that the existing landscaping will need to be removed and replaced. Our professionals, on the other hand, may propose that the new system be installed in a different place in order to minimize interference with plant and tree roots. The Florida Department of Health mandates that the following distances be respected in order to prevent groundwater pollution from septic systems:

If the property is located more than 75 feet from the annual flood line of a permanent, non-tidal surface water body or from the high water line of a tidal body of water, the following restrictions apply: 15 feet from a dry drainage ditch or stormwater retention area
10 feet from stormwater pipelines
At least 200 feet away from public drinkable wells that are already in use for non-residential or residential structures with a total daily sewage discharge of more than 2,000 gallons
And At least 11 feet away from any water storage tanks that come into touch with potable or groundwater
A minimum of 15 feet away from a groundwater interceptor drain is required
Minimum distances between bays, lakes and surface water
Minimum distances between multi-family wells and/or private potable water wells
And minimum distances between other wells.

New Home ConstructionSeptic Systems

Construction of new dwellings in rural locations or in any area that is not served by a municipal sewer system necessitates the installation of septic systems. Any system installed as part of a new house building project will have to take into consideration the elements and laws outlined above. In addition to establishing septic systems for countless new houses, Jones PlumbingSeptic Tank Service is happy to assist you through the application and permitting process, in addition to properly installing the system.