When Do You Need A Riser For A Septic Tank? (Correct answer)

  • Deep septic tanks should have a service riser installed. If the septic tank happens to be buried more than just a few inches below ground surface, good practice includes installing a septic riser, a large diameter pipe that gives good access to the septic tank for inspection and cleaning. Click to see full answer.

Is a septic riser necessary?

Installing septic tank risers are a highly recommended addition to your septic system. The septic tank riser will make maintaining and monitoring your septic system much easier and more convenient.

Why do I need a riser on my septic tank?

It creates a vertical portal at the ground surface for easy access to the septic tank for inspection and pumping out. Having a riser in place can also significantly reduce the cost of septic tank maintenance over time through the ease of access and time on the job saved.

Should septic tank riser be above ground?

Landscaping Around Septic Tank Risers However, septic tank risers should never be buried. Instead, they should be 2 inches above final grade to prevent groundwater from entering the system.

Are septic tank risers safe?

Fortunately, lids and risers in today’s onsite market can help prevent these unfortunate incidents. These innovative products ensure septic tank covers are secure and prohibit unauthorized tank access. Polyethylene septic tank covers from Hedstrom Plastics fit standard 18- and 24-inch double-wall corrugated pipe.

How many lids are on a septic tank?

A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

Do they make square risers for septic tanks?

The Polylok square riser adapter ring is designed to connect the Polylok septic tank risers or lids to an existing concrete tank with large square or round openings.

How do you hide a septic tank riser?

The easiest way to hide your septic riser is by simply placing something over it, such as a hollow, lightweight landscape rock, a birdbath, a sundial or a decorative lawn ornament. Apply basic landscaping principles when deciding what to use.

How high should septic tank riser be?

Tank risers are typically installed about 3 inches above grade. Having the lid above grade will make it easy to find, however, some people will choose to have the lid just a couple of inches below grade so that is easier to mow over and less visible.

How much weight can a septic tank riser lid hold?

The 24-inch solid fiberglass DuraFiber riser lid from Orenco Systems has a flat-style lip for PVC and HDPE pipe. It weighs 10 pounds, but resists damage from lawn equipment and can withstand a 20,000-pound load.

Can you cover septic tank lids?

If you have a traditional septic system, the tank should be pumped every 3-5 years. That means that the septic lids should be accessible every 3-5 years. You can use almost any temporary, movable objects to cover your lids, like: Mulch (but not landscaping)

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

The benefits of septic tank risers

Installing septic tank access risers will save you money as well as your back. Accessing the septic tank is made simple by the use of rippers. | Photo courtesy of the Michigan State University College of Agriculture and Natural Resources The process of finding and pulling up the lid to your septic tank may be time-consuming and frustrating. In many cases, homeowners aren’t even sure where to begin their search for the lid to their septic tank. Some people are just unable to pull themselves out of a hole.

What method do individuals use to locate the buried treasure that is their septic tank lid?

Others look for a clue, such as a dead spot of grass or other visual signals, to help them find their way.

Whatever way you choose, digging it out is still necessary, and if the correct location cannot be discovered, another hole must be excavated.

  • Some counties, such as Kalamazoo, Oakland, and Otsego, mandate that septic tank access risers be erected; these are just a few examples.
  • Contact your Michigan County to find out about the most recent onsite waste water rules that apply to you.
  • A septic tank riser is a pipe that can be built of plastic, fiberglass, or concrete to carry waste away from the tank.
  • The lid is then either left uncovered or covered with a very thin layer of soil and grass, depending on the preference of the gardener.
  • It goes without saying that any modifications to your septic tank or system will need to be approved by your county environmental health department or another qualified inspector.
  • You may arrange the installation of a riser in your septic system to coincide with your usual septic system maintenance schedule.
  • It is also possible that having a riser in place will dramatically lower the overall cost of septic tank maintenance over time, owing to the increased ease of access and reduced time spent on the operation.
  • MSU Extension Educator Beth Clawson can provide further information on the onsite waste water systems you may be interested in.
  • The Michigan Department of Natural Resources has a team of natural resources educators working to provide aquatic invasive species instructional programming and support throughout the state.

You can reach out to an educator using MSU Extension’s ” Find an Expert ” search engine by searching for “Natural Resources Water Quality” in the keywords field. Resources:

Did you find this article to be informative?

You Might Also Be Interested In

If you have an older septic system, you may be wondering what a septic tank riser is and why you would need one. Traditional systems were designed to be out of sight, out of mind; they were buried for 15-20 years with no consideration given until they required emergency pumping or repair. Newer septic systems now have risers, which are a positive thing, since they provide a more efficient way of draining the tank. Septic tank risers provide simple access to your septic tank from the ground level as well as increased view into the operation of your septic system.

The Benefits of a Septic Tank Riser

If you have an older septic system, you may be wondering what a septic tank riser is and why you would need one. Traditional systems were designed to be out of sight, out of mind; they were buried for 15-20 years with no consideration given until they required pumping or repair in an emergency situation. Newer septic systems now have risers, which are a positive thing, since they provide a more efficient way of draining the tanks. Increased visibility into the functioning of your septic system is made possible by septic tank risers, which are accessible from the ground level.

  • Even when the ground is frozen, it is possible to get access during the winter months. Maintenance and pumping of the septic system may be done quickly and easily. Septic system repair should not need digging up your yard. A visual reminder of the importance of your septic system

The last advantage may appear to be somewhat counter-intuitive. What are the benefits of having a visual reminder of your septic system? Preventing premature septic system collapse is possible through periodic septic system maintenance. With a septic tank riser, you’ll not only be able to identify the position of your septic system, but you’ll also have a visual reminder to have your system pumped at least once every two to three years as well. However, the septic tank risers that we install are intended to fit in with the surrounding environment.

How Much a Septic Tank Riser Costs

Perhaps the most surprising advantage is the final one. What is the point of having a visual reminder of your septic system? Why would you want one? Septic system maintenance is important because it protects the system from failing prematurely. With a septic tank riser, you’ll not only be able to identify the position of your septic system, but you’ll also have a visual reminder to have your system pumped at least once every two to three years. However, the septic tank risers that we install are meant to fit in with their surrounding environment.

What are the benefits of a septic tank riser?

The last advantage may appear to be a little counter-intuitive. The reason why you’d want a visual reminder of your septic system is a mystery. Septic system maintenance is essential in preventing septic system failure before it occurs. In addition to knowing where your septic system is, a septic tank riser serves as an excellent visual reminder to have your system drained at least every 2 to 3 years.

Having said that, the septic tank risers that we install are intended to fit in with their surroundings. Despite the fact that it will serve as a useful visual reminder, it will not be an eyesore.

  • Even when the ground is frozen, it is possible to get access during the winter months. Maintenance and pumping of the septic system may be done quickly and easily. Septic system repair should not need digging up your yard. Your septic system will be visible as a reminder

The ability to gain access to the site even when the ground is frozen during the winter months Maintenance and pumping of the septic system may be completed quickly. Septic system repair does not necessitate digging up your yard Your septic system will be shown as a reminder.

How much does a septic tank riser cost?

In your house, your septic system is one of the most vital mechanical systems to have working properly. A septic tank riser, which costs only a one-time installation price, can safeguard your septic system for many years to come. The ease with which maintenance and pumping may be performed will almost instantly result in a return on your investment. You may also say goodbye to costly and unsightly excavations when it comes to upkeep. Although the ground may be frozen in winter, you will be able to inspect your septic system visually even during the coldest months of the year.

In addition to protecting your system and saving you money, a septic tank riser is a reasonably easy solution.

We’d be happy to tell you more about how septic tank risers might help you.

for an appointment or to learn more about our services.

Felix Septic Service is a company that provides septic service. 2020-05-19T15:44:01-04:00

5 Reasons to Install Septic Tank Risers

Most homeowners consider their septic system to be a “out of sight, out of mind” service that receives little or no attention unless there is a problem. Septic systems are buried underground, and if you aren’t sure where your tank and its components are, it might be tough to discover your access ports or manhole covers if you aren’t familiar with your property’s layout. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings.

  1. What is a septic tank riser and how does it work?
  2. Risers, sometimes known as “extensions,” are available in a variety of heights to raise any access port up to grade.
  3. Because the riser extends from your tank entrance to the lawn surface, it makes it much easier to reach your septic tank for pumping, maintenance, and inspections than it would otherwise be.
  4. Digging down to your septic tank lid or access port and fitting the riser to the entrance are the steps involved in installation.
  5. Then we’ll fill the area around the pipe with earth and put the lid on top of it once it’s in place.

To make the lid integrate smoothly into your yard and landscaping, you are invited to put grass or mulch around the top of the lid. The AdvantagesWhen it comes to septic tank risers, there are a plethora of advantages to consider.

  1. The expense of installing a riser is one-time, but the advantages are long-lasting. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times
  2. There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. This is in addition to the mess that it can create in your yard if the lid is buried several feet down
  3. Nonetheless, it saves you money. Time is money, after all! Furthermore, since it is simpler to reach your septic tank, our staff can complete your task or resolve your problem much more quickly
  4. It is critical to understand where everything is located. If you’re putting up a new patio, house addition, or backyard project, understanding where your tank and its components are located will be quite beneficial to your project. We’ll even draw you a schematic if you need one
  5. Just let us know.

Are you ready to talk to us about septic risers and how they can make your next septic pumping job a whole lot easier? For a $20 discount, call 717-898-2333 and mention this article. We provide service to homes and businesses across Central Pennsylvania, and if you know your tank is due for a pumping, we can install your risers at the same time that your tank is being serviced.

See also:  When Washer Drains Water Backs Up Into Shower On Septic Tank? (Solved)

undefined

The inefficiency of having to dig up your grass to access your septic tank whenever it has to be pumped or undergoes periodic maintenance is well known to those who own septic systems. However, while burying the tank below is a practical approach to keep it secure and hidden, it can make routine duties more complex, costly, and time-consuming. This is one of the primary reasons why many individuals prefer to install a septic tank riser. As the name implies, it is a concrete or plastic pipe that runs from the pump-out hole to the ground level of a sewage system.

If you’re deciding whether or not to acquire a tank riser, consider the following advantages and disadvantages:

  • Anyone who has had their septic tank pumped or needs periodic maintenance knows how inconvenient it can be to have to dig up your grass every time it has to be serviced or cleaned out. However, while burying the tank below is a simple approach to keep it secure and hidden, it can make performing routine operations more complex, expensive, and time consuming. The installation of a septic tank riser is becoming increasingly popular. As the name implies, it is a concrete or plastic pipe that connects the pump-out hole to the ground level of a septic system. An easy and cost-effective way to keep your septic tank in good working order is to simply install a septic tank riser. Prior Lake, Minnesota If you’re wondering whether or not to acquire a tank riser, consider the following benefits and drawbacks.

The inefficiency of having to dig up your grass to access your septic tank whenever it has to be pumped or undergoes normal maintenance is well known to those who possess a septic system. However, while burying the tank below is a simple approach to keep it secure and hidden, it can make routine duties more complex, expensive, and time-consuming. Many folks opt to have a septic tank riser installed for this reason. As the name implies, it is a concrete or plastic pipe that runs from the pump-out hole to the ground level of a septic system.

If you’re deciding whether or not to acquire a tank riser, consider the following benefits and drawbacks:

Benefits of Installing Septic Tank Risers

Many people consider their septic system to be a “out of sight, out of mind” service that they don’t think about until there’s an issue. Due to the fact that septic tanks are underground, it might be difficult to discover the access ports if you aren’t familiar with the area where your tank and its components are placed. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings. Continue reading to learn more about septic tank riser installation in the Twin Tiers region, or contact us to arrange service now.

  1. It is a large-diameter concrete or plastic pipe that runs vertically from the pump-out apertures or access ports on top of a sewage treatment system down to ground level.
  2. With a lid that fits firmly on top of the riser and lies flush with the ground, digging and searching are no longer necessary.
  3. Installation Every week, our staff completes the installation of risers.
  4. When feasible, we’ll pick a riser that will stretch all the way to the surface of your grass, or we’ll trim one to fit.

To make the lid merge perfectly into your yard or landscape, you are welcome to put grass or mulch around the top. Benefits When it comes to septic tank risers, there are a range of advantages to consider.

  1. The cost of installing a riser is a one-time expense. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times
  2. There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. Furthermore, it saves you money by avoiding the mess that it might create in your yard. We understand that time is money, and when our staff has simpler access to your septic tank, we can get your project done or your problem resolved more quickly. It’s critical to be aware of where things are at all times. Are you thinking of building a new patio, home extension, or backyard project? The ability to pinpoint the location of your tank and its components is quite beneficial. We’ll even draw you a schematic if you need one
  3. Just let us know.

Are you ready to speak with us about septic risers? When it comes to septic tank repair, this is a straightforward service that will make your life a whole lot simpler. To schedule service, please call us at: 607-564-7931.

What is Septic Tank Riser

If you are one of the twenty percent of houses in the United States who are not linked to a centralized sewer system, the likelihood is that you have a septic system installed in your yard. A septic system is a sewage maintenance system that is installed on-site. While you are no longer required to pay monthly sewer fees to your local municipality, you are still responsible for the upkeep and maintenance of your septic tank system. Septic Connection, for example, is an excellent choice for an experienced septic service company in your area.

  • Installation of an aseptic tankriser can help to reduce the amount of time spent on sewer maintenance.
  • Due to the fact that septic tanks are often constructed many yards below and even the lids are just a few feet deep, locating and reaching the tank lid may be a time-consuming and difficult task.
  • The installation of a septic tank riser is a cost-effective solution to this issue.
  • The Advantages and Disadvantages of a Septic Tank Riser The world is not full of rainbows and butterflies.
  • Septic tank risers are built of sturdy materials that protect the septic tank lid from the weather. They are installed on the outside of the tank. A septic tank riser not only makes the placement of your septic tank lid evident, but it also protects your septic tank against unintentional pressure buildup. It’s easy to lose track of where the septic tank is and end up parking your car over it or dumping heavy equipment on it, which is dangerous. In addition, homeowners may be concerned about the expense of installing a new septic tankriser, but it should be emphasized that installation is straightforward and inexpensive. In addition, the expense is insignificant when compared to the long-term savings. With a septic tank riser, you will save both time and money during future septic system maintenance because your septic service provider will be able to find the tank and perform the necessary repairs more quickly
  • And The problem of aesthetics is also a source of concern for many homeowners. The fact that you do not want a pipe protruding from your property is totally understandable. If aesthetics are important to you, inform your septic tank riser installation professional so that they can ensure that the riser is installed such that the top of the riser is a few inches below the ground surface. By doing so, you may cover the surface with a thin layer of dirt and grass.

The Process of Locating a Reliable Septic Tank Riser Installer South Carolina-based Septic Connection is a fully licensed and insured firm with years of industry expertise, competent experts, and a professional staff. Our state-of-the-art equipment enables us to complete installations in a short amount of time and at a cost that is reasonable to our customers. So you never have to worry about dealing with septic difficulties on your own again, we offer emergency services around the clock. Are you ready to form a partnership?

Septic Tank Risers

In what capacity does an aseptic tank riser serve, and why would you require one? If your septic tank service worker has to dig up your yard every time your septic tank has to be cleaned, you do not have a riser built, and it is probable that you have a concrete cover buried someplace underground. The Ariser septic tank lid replaces your old septic tank lid, allowing you to access your tank from aboveground, making it easier to manage. It is possible that installing a riser will lower the cost of pumping your tank (this is not a guarantee; be sure to inquire).

It may even be possible to gain access to your septic main for cleaning and inspection depending on your external pipe system.

However, if you have an older system, the majority of tanks were built with concrete lids that frequently degrade and are typically buried beneath the earth.

Most septic pumping companies also provide riser installation, and it is typically less expensive to consolidate services rather than buy them separately because you save on service fees by doing so.

Septic Tank Riser Styles

Septic tank risers are available in a variety of designs and are composed of a variety of various materials, including concrete. Despite the fact that some are built of concrete (which are the most durable), some people find them ugly. Concrete risers are more difficult to construct and may need the use of special equipment to lift them off trucks, increasing the labor costs even if the materials are less expensive. Septic covers made of polyethylene, PVC, and other plastic materials are lower in weight and come in a variety of heights to meet your demands.

  • The majority of designs may be made to fit your specific height requirements.
  • It should be noted that the load-bearing capacities of the lids varies.
  • Riser pipes are available in a variety of sizes ranging from 8 to 24 inches in diameter, with lengths varying based on the depth of your tank entrance.
  • Although it is possible to cover them with sod and mark their location in order to be able to raise them for maintenance, this defeats the point of accessibility and may lose you of the potential savings that come from not having to dig out your cover every time it has to be serviced.

Septic Tank Riser Cost

Depending on the size, the material, the design, and the installation, the cost of a septic tank riser can vary significantly. Spend at least $150 on a basic model, but keep in mind that they may cost up to $400 depending on the model you select. If you have a twin septic tank, double the above figure by two. The labor and supplies are one-time expenses that will be soon recouped by not having to pay for digging when you want pumping or inspections of your system. Most of the time, they can be installed in a half-hour or less.

Septic Tanks Risers- Bring Your Access To Ground Level

Depending on the size, the material, the design, and your installation, the cost of a septic tank riser might vary significantly. Plan on paying at least $150 for a basic model, but keep in mind that they may cost as much as $400, depending on the type you select. Increase this amount by two if you have two septic tanks. The labor and supplies are one-time expenses that will be soon recouped by not having to pay for digging when you want pumping or inspections in the future. A half-hour or less is generally enough time to complete the installation.

THE POLYLOK ADVANTAGE

Septic tank risers are available in a variety of shapes, sizes, and designs on the current market.

We believe our Polylok septic tank risers are the best money can buy in terms of quality. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

Pre-installed gaskets are included with every Polylok product, making it the only one on the market that does this. Because of this, there is no additional work needed to ensure that the riser system is airtight and watertight! This is critical in order to keep groundwater out of your tank, wastewater inside your tank, and potentially hazardous gases out of your yard! The majority of other solutions need you to purchase or apply some other type of sealant between each riser component, but with our Polylok septic tank risers, you won’t have to bother about that!

LIDS WITH HANDLES

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place. This implies that no further work is necessary to ensure that the riser system is both airtight and watertight! Important for keeping ground water out of your tank, wastewater inside of it and potentially hazardous gases out of your yard! Most other products need you to purchase or apply some other type of sealant between each riser part, but with our Polylok septic tank risers, you won’t have to worry about it!

See also:  How Much Copper Sulfate Roots In Septic Tank? (Perfect answer)

LARGE ADAPTER RING

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already attached. This implies that no further work is necessary to ensure that the riser system is airtight and watertight! This is extremely crucial in order to keep ground water out of your tank, wastewater inside your tank, and potentially hazardous gases out of your yard! The majority of other solutions need you to purchase or use some other type of sealant between each riser component, but with our Polylok septic tank risers, you won’t have to bother about it!

GET OUT YOUR MEASURING STICK!

A few measures must be taken before purchasing a septic tank riser system in order to ensure proper installation. The first thing to consider is the size of your opening. Take a measurement of the aperture in your septic tank at its widest point to determine the size of your tank. Instead than measuring the present lid, it’s critical to measure the opening. Because you will be removing the present cover, the measurements of the lid are no longer important and may differ from the size of the aperture itself.

You are now prepared to make a purchase based on these two measures!

THE COMPLETE RISER SYSTEM

We have a large selection of components from which you may pick to create your own own full riser system.

Our many various options offer our product the adaptability to be utilized in virtually any application, but they may also be a bit daunting when attempting to pick which components to buy for a certain application. Each component is discussed in further depth below.

ADAPTER RINGS

The adapter ring is the first component that you’ll need to put together in order to assemble a full riser system. The adapter ring attaches directly to the septic tank, allowing the risers to stack, lock, and mount to it without the need for any additional hardware. Having this component is critical since the risers are not flat on the bottom because they are meant to be stackable, and it is not feasible to install them straight to the septic tank without this piece. The adapter ring provides the flat surface you need to mount to the tank while also being able to accommodate the stackable risers that are included with the tank.

Our square tank adapter ring can accommodate big square apertures up to 25 inches in diameter and large round openings up to 27 inches in diameter.

They are intended to be used with openings that are 24″ or less in diameter.

Concrete anchors, a masonry bit for installing the anchors, and butyl sealer are all included in this set.

RISERS

Following your selection of the adapter ring, it is time to go shopping for risers. The Polylok risers are available in two heights: 6″ and 12″, as well as in two diameters: 24″ and 20″. Stackable, each unit has a gasket that has been fitted as well as stainless steel screws to allow for easy installation. Determine which risers will work best for your application based on the height measurement you made between the septic tank and ground level.

OPTIONAL SAFETY SCREEN

In addition to the 20″ and 24″ riser systems, Polylok also produces safety screens that fit within the riser systems. These screens serve as a supplementary layer of protection in the event that the riser cover is unintentionally damaged or removed, and they keep foreign objects from entering the septic tank. They also keep dogs from slipping into unprotected septic tank openings!

RISER LIDS

You will require a lid to complete your riser system, which is the final component you will require. Both the 20″ and 24″ riser systems may be used with the Polylok lids, which are available in two different types to suit your needs. For ease of access, the basic lid is equipped with handles and a gasket that has been factory placed, as well as stainless steel screws to keep it in place. These lids are strong enough to withstand foot traffic as well as the weight of a riding lawn mower driving across them.

Stainless steel screws are included for installation.

Installations below grade or in regions with a high volume of foot traffic are advised for the heavy-duty lids.

The shipping of these items in large boxes necessitates the addition of additional time, materials, and UPS shipping fees.

SIMPLY ADD THE ITEMS TO YOUR SHOPPING CART AND THEN CHECK YOUR SHIPPING COST. If you place your order before 2 PM CST, you will be able to get your order sent the same day you placed it.

FREQUENTLY ASKED QUESTIONS

You will require a lid to complete your riser system, which is the last component. Both the 20″ and 24″ riser systems may be used with the Polylok lids, which are available in two different types to match your needs. For ease of access, the basic lid is equipped with handles and a gasket that has been factory placed, as well as stainless steel screws to secure it in position. A riding lawn mower may be driven on these lids without causing damage. They can also withstand foot usage. Heavy Duty lids are the second type of lid we provide.

They are also available in a variety of colors.

These goods may all be purchased from the following websites: NOTICE: FREE SHIPPING IS NOT AVAILABLE ON ORDERS FOR SEPTIC TANK RISERS AND LID.

SIMPLY ADD THE ITEMS TO YOUR SHOPPING CART TO RECEIVE THE SHIPPING COSTS.

WILL THE LID FIT DIRECTLY ON THE ADAPTER RING OR DO I NEED TO USE A RISER?

With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength. The height of this reinforcement is actually more than the height of the adapter ring. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter. The lid will not fit through any aperture less than 24 inches in diameter.

CAN I CUT THE RISER SYSTEM DOWN TO A SPECIFIC HEIGHT?

In most situations, with the exception of the 24″ Heavy Duty Lid, the lid will fit straight onto the adaptor rings. At the bottom, the Heavy Duty Lid measures 24 inches in diameter and is strengthened. Actually, the height of this reinforcement is higher than the height of the adapter ring. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter ring if your opening is at least 24″ wide. It is not possible to use the lid if the aperture is less than 24 inches in diameter.

DO I BRING THE RISER SYSTEM JUST BELOW, AT, OR ABOVE GRADE?

It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade. Because the riser system is airtight and watertight, there is no danger in moving it up to or above grade level.

SHOULD I USE THE STANDARD OR THE HEAVY DUTY LID?

The regular lid is sturdy enough to withstand foot activity and weights up to the weight of a small riding lawn mower passing over it without bending or breaking.

If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].

What is a Septic Tank Riser?

  • When used as intended, the regular lid can withstand foot traffic and weights up to the weight of a small riding lawn mower passing over it without breaking. In areas with high traffic or where the riser system will be run over by lawn equipment on a frequent basis, the heavy-duty lid is recommended for further protection. Further questions should be directed to 1-877-925-5132 or [email protected]

The regular lid is sturdy enough to withstand foot activity and weights up to the weight of a small riding lawn mower passing over it without breaking down. If the riser system is located in a high traffic location or will be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended. If you have any queries, please contact us at 1-877-925-5132 or [email protected].

What Is a Septic Tank Riser?

The regular lid is sturdy enough to withstand foot traffic and weights of up to a small riding lawn mower passing over it. If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, we recommend the heavy duty lid. For any more queries, please contact us at 1-877-925-5132 or [email protected].

The Benefits: How Septic Risers Save You Money

As a rule of thumb, septic system manufacturers recommend that you examine your septic tank once a year and pump your septic tank every three to five years. However, if your septic system is not equipped with a riser, you may be forced to pay additional fees.

No Digging Fees

You or your septic tank specialist will have to spend time and money digging through the earth to locate your tank if you or he does not know the precise position of your tank. Your septic tank will need to be recovered with earth once it has been serviced and pumped without a riser, and they will need to do this every time they service your septic tank going forward.

Reduces Labor Costs

Incorporating an easily visible septic tank riser makes it easier for the contractor to access the riser lid, insert the pump hose, and start to work more quickly and efficiently. In this case, they may leave their heavy equipment at home, which saves you from having to spend a large amount of money in labor.

You’ll Only Pay for Materials and Labor Once

When you have a septic tank riser installed, you will only be responsible for the labor and materials used in the installation. The money you save on yearly inspections and regular local maintenance will more than compensate for the cost of the septic tank riser over time.

Septic Tank Riser Styles

Image courtesy of Ekaterina / Adobe Stock Septic tank risers are available in a variety of concrete and plastic types ranging in size from eight to 24 inches. Each style has its own set of pros and disadvantages.

Concrete Septic Tank Risers

Concrete septic tank risers are more durable than other materials, but they have certain drawbacks of their own. Pros:

  • Depending on how well it is maintained and drained, it can endure for 40 years. Septic tank risers made of steel are more durable than those made of plastic. Require less upkeep than plastic
  • With correct drainage and upkeep, it can endure up to 40 years. septic tank risers made of metal are more durable than plastic ones. Maintenance is less involved than with plastic

Plastic Septic Tank Risers

Plastic septic tank risers are available in a variety of materials, including PVC and polyethylene, among others. Pros:

  • Purchase and installation costs are less expensive than those of concrete. Transport does not necessitate the use of large equipment. When compared to concrete septic tank risers, they are lighter in weight
  • They may be covered with sod to improve their looks
  • It is not susceptible to cracking like cement. Plastic is resistant to erosion.
  • It is possible to crush it beneath the earth
  • However, it is not as durable as concrete. Maintenance is more difficult to keep up with than with plastic.

How Much a Septic Tank Riser Costs

Installing a septic tank riser will cost between $200 and $400. Double septic tank risers will cost you twice as much as a single riser. It is more expensive to build concrete risers than it is to install plastic risers because of the weight of the concrete risers and the equipment necessary for installation.

Installation Usually Requires a Plumber

Septic tank riser installation can run you $200 to $400. Double septic tank risers will cost you twice as much as one. Because of its weight and the equipment required for installation, concrete risers are more expensive to install than plastic risers.

How to Care for Your Septic Tank Risers

You will not be short of resources when it comes to learning how to properly care for your septic system, since there is a lot of information available on the basic maintenance of your system. The instruction on how to properly care for your septic tank risers, on the other hand, is conspicuously absent.

Despite the fact that they are seldom given much attention, they are an extremely vital component of your septic system. In this post, we’ll go over how to properly care for your septic tank risers, as well as how to determine when it’s time to repair or replace them.

What are Septic Tank Risers?

Sewage tank risers are straightforward in construction, consisting of concrete, plastic, or fiberglass pipes that stretch vertically from the septic tank up to the ground level. It is usual for them to be 12-24 inches in diameter and 2-4 feet in length, depending on how far below earth your tank has been buried. In order for your service provider to have access to your buried septic tank for service visits or inspections, risers must be installed at ground level on your property. It has been around twenty years since septic tank risers have been needed for all systems in the state of Ohio.

See also:  How To Tell If Septic Tank Divider Broke? (Question)

Proper Installation of Septic Tank Risers

Unlike previous versions consisting of clay tile, which were prone to cracking when struck by a lawnmower, modern septic tank risers are composed of concrete, plastic, or fiberglass, and are therefore far more durable. Because they feature rubber gaskets between portions and are fastened together, today’s risers provide a better seal than their clay equivalents of the past. To the contrary, septic tank risers should be completely waterproof in order to prevent groundwater from entering your tank.

Landscaping Around Septic Tank Risers

You’ll discover a plethora of resources on the internet that advise disguising septic tank risers by burying them under mulch or just beneath the surface of the soil. Septic tank risers, on the other hand, should never be buried. To avoid groundwater entering the system, they should be 2 inches above final grade rather than 2 inches below final grade. Mulch should not be used near septic tank risers. It is possible that mulch will fall into the tank during inspections and servicing visits, producing unsightly blockages and perhaps causing major damage.

Keep in mind that the vegetation you grow around your septic tank risers should be considered as well.

Tall ornamental grasses have particularly problematic roots, which can make them difficult to maintain.

Common Issues with Septic Tank Risers

Tank risers, like every other component of your septic system, should be inspected on a regular basis to verify that they are in perfect working order and are not in need of repair. The most common problem we see with septic risers is damage caused by the lawnmower, which occurs when homeowners bump into or drive over the riser with their vehicle. Make certain that anybody who will be caring for your grass is aware of the location of the risers and understands the necessity of not striking them with any maintenance equipment, such as lawnmowers, weed eaters, and the like.

Northeast Ohio’s varied temperatures, particularly during our frosty season, have the potential to move them and cause the watertight barrier to collapse.

When inspecting for infiltration, open the lid of the riser and circulate water around it for 10 minutes while keeping an eye out for signs of leakage. The risers will need to be fixed if water is seeping into the system, and this will prevent groundwater from coming into your plumbing system.

Supeck Septic is Your Trusted Septic Service Provider

Supeck Septic is the leading septic service provider in Northeast Ohio, and the company has been providing great customer care since its founding in 1968. We are fully licensed, bonded, and insured to provide routine and emergency septic services, including the installation and repair of septic tank risers, to both residential and commercial customers. We retrofit old tanks with new risers, repair existing risers, and supply all of the components and accessories needed for the do-it-yourselfer.

Articles that are related Mulch your septic system to keep it running smoothly.

Grants for the Upgrade and Repair of Septic Systems in Ohio

Installing Access Risers

In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below. Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.

A few safety tips before you get started:

  • Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website
  • Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.

Gather all the MaterialsTools You will Need

It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.

Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.

Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.

See below for Step 4 on attaching risers to the tank entrance.

  1. Tank Adapter Ring (TAR)
  2. Riser Adapter Ring Kit
  3. Butyl Rope
  4. Risers
  5. Domed Lid OR Flat Lid
  6. Stainless Steel Screws

The following materials will be required for digging up your septic tank(s):

  1. As-built condition of the sewage treatment system The following items are required: sketch on paper, measuring tape, shovel, probing instrument, eye protection, and work gloves.

To cut risers to the proper size, the following tools are required:

  1. Circular saws, saber/jig saws, and hand saws
  2. Drilling with a 1/4-inch bit File containing Raspor
  3. Markingpen
  4. A tape measure is a tool used to measure anything.

Materials required to seal the risers to the tank include:

  1. High-strength concrete patch mix
  2. A small bucket
  3. A mixing stick
  4. And gloves

Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.

Step 1: LocateYour Septic Tank(s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.

Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.

The presence of underground electricity or other utility lines and cables might put your septic tank in danger.

Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.

Step 2: Uncover Your Septic Tank (s)

Once you’ve discovered your septic tank, you may start digging about. The tank is typically 6 feet wide by 8 feet long, with the width being the largest size. Remove all of the pebbles and debris from around the tank’s lid openings and dig out the whole top of the tank. You will want to clean out any dirt that has accumulated on the surface of your septic tank. This will assist you in ensuring that you generate a high-quality seal. You should have two openings: one over the inlet (which comes from the home) and another over the outlet (which comes from the yard) (into the drainfield or pump chamber).

  • You’ll need a riser for each of the doors you open.
  • Typically, the inlet side is the one that is nearest to the home.
  • When cleaning the tank, it is beneficial to remove the complete top of the tank.
  • Risers must be modified in order to be correctly installed, and all manholes (holes 24 inches or bigger in diameter or square in shape) must also be updated, as well as the tankinlet and outlet baffle covers (if separate from the manholes).
  • If you discover one – and only one – riser already installed, it is most likely for the pump chamber, which only requires a single riser to provide access to the pump to function properly.
  • Remove the concrete lids so that they may be disposed when the project is completed.
  • Consult your’As-built’Recorddrawing to establish whether you have a distribution box (D-box), which you will also need to unearth and place a riser on if you have a typical gravity system.
  • Once the lids have been removed, proceed with caution around the tank.
  • Inform someone of your whereabouts in case you are involved in an accident.

You should be aware that exposure to sewage can result in serious sickness, so make sure you wear gloves and thoroughly wash your hands afterward with soap and water. It is also recommended that you wear eye protection in the event that debris falls into a tank and splashes back at you.

Step 3: Fit Risers to Component Openings

In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:

  • Theriser will fit into the tank hole if the aperture is between 26 and 29 inches in diameter. Measure the distance from the ground to the top of the septic tank and multiply the measurement by three inches. The following is required if the aperture is greater than 29 inches: a 3-foot square fiberglass plate (with a 22-inch hole in the middle) is required. In this case, it lies above the manhole and narrows the aperture, allowing a 24-inch riser to be utilized instead of a more expensive 30-inch riser, saving money.

The distance between the ground and the top of the fiberglass plate should be measured. You may choose to place the risers so that they are level with the surface of the ground, or you may want them to stand out a few inches above the ground (if a riser is above ground make sure you are careful when mowing). Tips: To shorten a big riser with ribs, drill a 1/4-inch hole between the ribs above the cut line and finish the cut by following one of the grooves between the ribs with a saber/jig saw to finish the cut.

By eliminating one of the ribs from the largeriser, it may be made to fit more snugly into a smaller manhole entrance.

Step 4: Attach Risers toSeptic Tank (s)

It is recommended to pump out an old septic tank that is 20 years or older in order to check its structural integrity and water-tightness before using it again. If the tank requires extensive repairs, it is preferable to replace it with a new septic tank that includes risers as part of the installation. A permit from the local health department is required for the replacement of a septic tank. Remove any dirt and debris from the tank’s surface by cleaning it off. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s instructions.

Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names available.

NOTE: For optimal results, just a little amount of concrete patch should be mixed at a time.

The patch mix should be used to seal the riser to the septic tank.

If you want to avoid a safety danger, make sure you properly attach theriser lid using the screws that come with it!

Risers for inlet or outlet apertures that are smaller than the openings should have the bottom few inches sanded with rough sandpaper to allow a firmer connection between the two surfaces.

A useful source of information on correct installation of risers on septic tanks may be found at your local hardware store where you purchased the risers and covers.

Thurston County Environmental Health is should be commended for providing the foundation for this documentation.

Leave a Comment

Your email address will not be published. Required fields are marked *