What Size Septic Tank Do I Need Az? (Question)

Sizing rules vary slightly from location to location. In Arizona, for example, a three-bedroom house with two bathrooms and roughly 20 fixtures requires a tank of at 1,250 gallons. A building with 14 occupants and three to five baths requires a 2,000-gallon tank.

The recommendation for home use is a 1000 gallon septic tank as a starting point. The 1000 gallon size tank is a minimum and *can be suitable for a 2 bedroom, 3 bedroom house. Some recommendations say to add an extra 250 gallons of septic tank capacity for each bedroom over 3 bedrooms.

How do I know what size septic tank I need?

The larger your home, the larger the septic tank you’re going to need. For instance, a house smaller than 1,500 square feet usually requires a 750 to 1,000-gallon tank. On the other hand, a bigger home of approximately 2,500 square feet will need a bigger tank, more than the 1,000-gallon range.

Can I install my own septic system in Arizona?

SITE EVALUATION – Although conventional septic systems may be installed by the homeowner if certain criteria are met, the site evaluation must be done by an Arizona- registered professional engineer, geologist, sanitarian, an appropriately licensed septic or plumbing contractor (K-41 or L-41) who has completed training

How big should a septic tank be for a 3 bedroom house?

The correct size of the septic tank depends mostly on the square footage of the house and the number of people living there. Most residential septic tanks range in size from 750 gallons to 1,250 gallons. An average 3-bedroom home, less than 2500 square feet will probably require a 1000 gallon tank.

How often does a 1000 gallon septic tank need to be pumped?

For example, a 1,000 gallon septic tank, which is used by two people, should be pumped every 5.9 years. If there are eight people using a 1,000-gallon septic tank, it should be pumped every year.

How do I calculate the size of my septic drain field?

Drainfield Size

The size of the drainfield is based on the number of bedrooms and soil characteristics, and is given as square feet.

For example, the minimum required for a three bedroom house with a mid range percolation rate of 25 minutes per inch is 750 square feet.

How much does it cost to build a septic tank in Arizona?

Installing a new conventional septic system can cost from $4,000 – $5,000 +/-. Alternative systems may cost in the range of $10,000 – $20,000… or more. In Arizona, an estimated one of every five households is served by some type of onsite wastewater system.

How long do septic tanks last in Arizona?

The usual design life of a septic system is 20 years.

What is the alternative to a septic tank?

Mound systems work well as alternatives to septic tanks when the soil around your home or building is too dense or too shallow or when the water table is too high. Although they are more expensive and require more maintenance than conventional systems, mound systems are a common alternative.

How deep should a septic tank be?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

Can you have a septic tank without a leach field?

The waste from most septic tanks flows to a soakaway system or a drainage field. If your septic tank doesn’t have a drainage field or soakaway system, the waste water will instead flow through a sealed pipe and empty straight into a ditch or a local water course.

Is a 500 gallon septic tank big enough?

The minimum tank size for a three bedroom house is 1200 gallons. 500 or 750 gallon tanks used to be quite common in old houses, but they are not large enough for modern households, and are from a time without automatic washers, large spa tub, dishwashers, or multiple daily showers.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

Septic Systems

Having your land inspected to determine the size and location of the septic system before constructing a house, construction, or well is the first step. If you have to shift buildings on paper because of setbacks or the scale of the system, it will be easier to do it on paper. In order to do so, you must engage the services of a state-certified evaluator to undertake a soil and site assessment. They will drill at least three test pits (two in the major sewage disposal area and a third in the reserve disposal field region) to a depth of 12 feet in order to assess the soil’s ability to absorb water as well as any restricting factors that may exist.

Before you may submit an application for a sewage disposal permit, you must first complete the soil and site examination.

Because of limiting conditions such as a lack of soil, high groundwater, impermeable layers, and so on, an alternative system (composting toilets are an example of an alternative system) will be recommended to you, and you will be responsible for designing a system to compensate for whatever the limiting condition is.

SiteSoil Evaluator

A competent Investigator/Evaluator can take one of the following roles:

Individuals who have received a certificate of training from a course recognized by the Arizona Department of Environmental Quality

Individuals who are Arizona registered professional engineers
Individuals who are Arizona registered professional geologists
Individuals who are Arizona registered sanitarians

CareMaintenance

Septic systems that are not properly maintained or that are failing are major causes of water contamination and possible public health problems. This information will aid you in managing your septic system for optimal sewage treatment and the longest possible life expectancy:

The septic system is a two-part sewage treatment and wastewater disposal system that is installed underground. It is made up of two components: a septic tank and a leach field. The sewage flows into the septic tank via gravity, where the particles are collected and some treatment takes place. The residual liquid drains to leach fields, where it is further treated before being allowed to seep into the soil. It is advised that the septic tank be pumped every 3 to 5 years if the home is used regularly for a long period of time. Contractors can be found in the telephone directory (in the yellow pages under Septic Tanks and Systems-Cleaning). As a result, if solids from your tank are permitted to reach the leach field, the life of your system might be dramatically reduced, resulting in costly repairs much sooner than would normally be expected. Consult your local Cochise County Environmental Health Division office for assistance in determining the location of your septic tank system. Your local government agency may be able to provide you with information on where your septic tank is in relation to your home if your house is not too old. Another option would be to personally search the yard to see if you can locate it that way. Certain clues, such as a cleanout pipe, may be hidden in your backyard. There is a direct connection from this line to the tank, which is often 10 feet or more away from the house’s foundation. An experienced plumber or septic tank pumping business may also assist you in locating the tank. Recent models of residential septic tanks are equipped with an effluent filter, which is located within the tank’s second chamber before the outlet or discharge line. The effluent filter’s aim is to prevent particles from seeping into the leach fields during the treatment process. It is necessary to clean the effluent filters on a regular basis. Removing it from the tank and cleaning it well with running water can effectively clean the filter. These filters may be cleaned by you or your septic pumper. In most cases, cleaning should be done at least once a year
The effectiveness of the septic system is connected to the amount and quality of effluent. The repair of any leaky fittings should be carried out as soon as feasible. In normal proportions, household cleaning chemicals would have no negative effects on the environment. Pesticides, herbicides, paint, solvents, and oils should not be disposed of in the septic system. It is not suggested to use chemicals or bacterial enzymes in your compost. In most cases, failure of a septic system is signaled by either sewage backing up into the residence or effluent appearing in the leach field area. When this occurs, you must establish the root reason and take steps to resolve the problem. It might indicate that the septic tank needs to be pumped and/or that the leach field’s ability to manage the intake of wastewater is reducing in capacity. The release of wastewater into the environment is considered a public health issue. A quick fix is required, such as pumping the tank and maybe getting a repair permit from the Environmental Health Department if repairs to the septic system are required.

What size of septic tank do I need?

It is a sewage treatment and wastewater disposal system that is installed underground in two parts. Septic tanks and leach fields are the components of this system. Gravity transports sewage to the septic tank where particles are removed and some treatment is performed. A septic tank should be pumped every 3 to 5 years if it is used for typical home purposes since the residual liquid goes to leach fields where it is further treated before being absorbed into the soil. In the telephone directory, you may find information on contractors (in the yellow pages under Septic Tanks and Systems-Cleaning).

The Cochise County Environmental Health Division office closest to you can assist you in locating your septic tank system.
It’s also possible to personally search the yard to see if you can locate it this way.

There is a direct connection between this line and the tank, which is often 10 feet or more away from the home’s foundation.
Most newer septic tanks include an effluent filter installed within the tank’s second chamber, prior to the tank’s outlet or discharge line.
Regular cleaning of effluent filters is required.

These filters may be cleaned by you or by your septic pumping company.
The repair of any leaky fittings should be carried out as soon as practical.
Chemicals such as disinfectants (such as bleach), pesticides, herbicides, paint, solvents, and oils should not be disposed of in the septic tank.

In most cases, failure of a septic system is signaled by either sewage backing up into the house or effluent appearing in the leach field area.
It might indicate that the septic tank needs to be pumped and/or that the leach field’s capacity to manage the intake of effluent is deteriorating as a result.

Public health is deemed to be endangered when wastewater is exposed to the environment. A quick fix is required, such as pumping the tank and maybe getting a repair permit from the Environmental Health Department if repairs to the septic system are necessary.

septic tanks for new home construction

The exact size of the septic tank is determined mostly by the square footage of the house and the number of people who will be living in it. The majority of home septic tanks have capacities ranging from 750 to 1,250 gallons. A 1000 gallon tank will most likely be required for a typical 3-bedroom home that is smaller than 2500 square feet in size. Of course, all of this is dependent on the number of people who live in the house as well as the amount of water and waste that will be disposed of through the plumbing system.

For the most accurate assessment of your septic tank needs, you should speak with an experienced and trustworthy sewer business representative.

planning your drainfield

Here are some helpful hints for deciding where to locate your drainfield when you’re designing it.

Vehicles should not be allowed on or around the drainfield. Planting trees or anything else with deep roots along the bed of the drain field is not recommended. The roots jam the pipes on a regular basis. Downspouts and sump pumps should not be discharged into the septic system. Do not tamper with or change natural drainage features without first researching and evaluating the consequences of your actions on the drainage field. Do not construct extensions on top of the drain field or cover it with concrete, asphalt, or other materials. Create easy access to your septic tank cover by placing it near the entrance. Easy maintenance and inspection are made possible as a result. To aid with evaporation and erosion prevention, plant grass in the area.

a home addition may mean a new septic tank

Vehicles should not be allowed on or near the drainfield. Planting trees or anything else with deep roots near the drain field’s bed is not recommended. Clogged pipes are frequently caused by the roots of plants; Downspouts and sump pumps should not be drained into the septic system; and If you want to tamper with or change natural drainage characteristics, do so after researching and evaluating the impact on the drain field. Do not construct extensions on top of the drain field or cover it with concrete, asphalt, or other similar materials.

Easy maintenance and inspection are made possible as a result of this; To aid with evaporation and erosion prevention, plant grass in the soil.

For a home addition that will result in increased use of your septic system, your local health department will require a letter from you that has been signed and authorized by a representative of your local health department confirming that your new septic system is capable of accommodating the increase in wastewater. It is not recommended that you replace your septic system without the assistance of a certified and competent contractor.

how to maintain your new septic system

Septic tank cleaning and septic tank pumping services are provided by Norway Septic Inc., a service-oriented company devoted to delivering outstanding septic tank cleaning and septic tank pumping services to households and business owners throughout the Michiana area. “We take great delight in finishing the task that others have left unfinished.” “They pump, we clean!” says our company’s motto. Septic systems are something we are familiar with from our 40 years of expertise, and we propose the following:

Make use of the services of a qualified specialist to develop a maintenance strategy. Make an appointment for an annual examination of your septic system. Utilize the services of an effluent filter to limit the amount of particles that exit the tank, so extending the life of your septic system. Waste items should be disposed of properly, and energy-efficient appliances should be used. Make sure you get your septic system professionally cleaned every 2 to 3 years, or more frequently if necessary, by an experienced and qualified expert

If you have any reason to believe that there is an issue with your system, contact a professional. It is far preferable to catch anything early than than pay the price later. Maintain a record of all septic system repairs, inspections, and other activities

common septic questions

Here are some of the most frequently asked questions by our septic customers.

How do I determine the size of my septic tank?

Our septic clients frequently ask us the following questions:

How many bedrooms does a 500-gallon septic tank support?

How deep in the ground is a septic tank?

Your septic system is normally buried between four inches and four feet underground, depending on the climate.

How to Calculate Septic Tank Size

If you find yourself on the verge of needing a larger septic tank than you anticipated, be liberal with your calculations and purchase a little larger septic tank. When it comes to septic tanks, having a little excess space is preferable to not having enough. sewage can back up into your home if a septic tank is installed that is too small for the job. When installing a septic tank, it is critical that you determine the proper size for the job.

The majority of towns require even the smallest septic tanks to carry a minimum of 1,000 gallons of wastewater. As the number of bedrooms, occupants, bathrooms, and fixtures that will be serviced by the septic system rises, the needed capacity for the system increases accordingly.

Step 1

Calculate the number of inhabitants who will be utilizing your septic system on a regular basis. The majority of towns believe that a two-bedroom house will have four regular inhabitants, even though the property only has two bedrooms. A three-bedroom residence may accommodate up to six people.

Step 2

The number of bathrooms that will be served by the septic tank should be counted. If you just have one bathroom but want to add another in the future, make sure to include the second bathroom in your count to avoid having to replace your tank further down the line.

Step 3

In your home, make a list of all of the plumbing fittings you have. This figure includes all faucets, toilets, showers, dishwashers, laundry washers, and any other fixture that will drain into your septic tank. It does not include your water heater.

Step 4

Take your calculations to your local permit office, where they will be checked against your local rules in order to establish the acceptable septic tank sizing for your home or business. The guidelines for clothing sizing differ somewhat from one place to the next. As an example, in Arizona, a three-bedroom house with two bathrooms and around 20 fixtures requires a tank that holds approximately 1,250 gallons. A 2,000-gallon water tank is required for a structure with 14 residents and three to five bathrooms.

Septic Tank Size: What Size Septic Tank Do You Need?

Take your calculations to your local permit office, where they will be checked against your local rules in order to establish the right septic tank sizing for your home and yard. From one place to the next, the standards for clothing sizing differ slightly. When building a three-bedroom house with two bathrooms and around 20 fixtures in Arizona, the tank must hold at least 1,250 gallons of water. A 2,000-gallon tank is required for a building with 14 residents and three to five bathrooms.

Basics of Septic Tanks

Your septic system is a self-contained chamber that is designed to retain the wastewater generated by your home. A septic system is comprised of two major components: the soil absorption area or drain, and the holding tank. Septic tanks absorb solid waste when wastewater is discharged into them, resulting in the formation of an asludge layer at the septic tank’s base. A layer of soap residue, grease, and oil forms on the top of the water. The effluent or wastewater is contained within the intermediate layer.

To discover more about how a septic tank works, check out our page that goes into further detail on how a septic tank functions.

The Main Types of Septic Tanks

Before you start thinking about septic tank sizes, it’s important to understand the many types of septic tanks that exist.

Septic tanks made of fiberglass
Septic tanks made of plastic

Septic tanks made of concrete

Concrete septic tanks are the most prevalent variety, but since they are so massive, you will need big and expensive equipment to build them. Fiberglass and plastic septic tanks are lighter than concrete and are therefore more suited for difficult-to-reach and distant locations.

Before purchasing a septic tank, you should check with your local building department to learn about the rules and guidelines governing private wastewater management. You may also be interested in:Do you have a septic tank?

Why Septic Tank Sizes is Important

If the capacity of your home’s septic tank is insufficient to satisfy your requirements, it will be unable to handle the volume of wastewater generated by your home. As a result, a wide range of annoying difficulties can arise, including bad smells, floods, and clogs. Nonetheless, the most common consequence of a septic tank that is too small is that the pressure that builds up will cause the water to be released before it has had a chance to be properly cleaned. This suggests that the solid waste in the septic tank will not be sufficiently broken down, and will thus accumulate more quickly, increasing the likelihood of overflows and blockages in the system.

A septic tank that is too large will not function properly if it does not get the required volume of wastewater to operate.

What Determines Septic Sizes?

Here are some of the elements that influence septic tank sizes; keep them in mind when making your purchase to ensure that you get the most appropriate septic tank for your property.

Consider Your Water Usage

The most accurate and practical method of estimating the appropriate septic tank size for your property is to calculate the quantity of water you use on a regular basis. The size of the septic tank required is determined by the amount of water that can be held in it before being drained into the soil absorption field. In many places of the United States, the smallest capacity of septic tank that may be installed is 1,000 gallons or less. The following are the suggested septic tank sizes for your household, which are based on your household’s entire water use.

A septic tank with a capacity of 1,900 gallons will handle less than 1,240 gallons per day
A septic tank with a capacity of 1,500 gallons will handle less than 900 gallons per day. A septic tank with a capacity of 1,200 gallons is required for less than 700 gallons per day
A septic tank with a capacity of 900 gallons is required for less than 500 gallons per day.

Consider the Size of Your Property

Another factor to consider when determining the most appropriate septic tank size for your home is the square footage of your home. The size of your home will determine the size of the septic tank you will require. For example, a dwelling with less than 1,500 square feet typically requires a tank that holds 750 to 1,000 gallons. On the other side, a larger home of around 2,500 square feet will require a larger tank, one that is more than the 1,000-gallon capacity.

The Number of Bedrooms Your Property Has

An additional issue to consider is the amount of bedrooms in your home, which will influence the size of your septic tank. The size of your septic tank is proportional to the number of bedrooms on your home. The following table lists the appropriate septic tank sizes based on the number of bedrooms.

In general, a 1-2 bedroom house will require a 500 gallon septic tank
A 3 bedroom house will demand 1000 gallon septic tank
A 4 bedroom house will require 1200 gallon septic tank

And a 5-6 bedroom house would require a 1500 gallon septic tank.

The Number of Occupants

In general, the greater the number of people that live in your home, the larger your septic tank must be. In the case of a two-person household, a modest septic tank will be necessary. If your house has more than five tenants, on the other hand, you will want a larger septic tank in order to handle your wastewater more effectively and hygienically. When determining what size septic tank to purchase, it is important to remember that the size of your septic tank determines the overall effectiveness of your septic system.

As a result, it is critical that you examine septic tank sizes in order to pick the most appropriate alternative for your property in order to avoid these difficulties. Please contact us to determine the optimal septic system size for your North Atlanta, GA house.

Arizona Septic Tank Installations

The size of your septic tank is proportional to the number of people that live in your home. For example, if your house has just two tenants, you will only require a tiny septic tank. If your home has more than five people, on the other hand, you will want a larger septic tank in order to manage your wastewater more effectively and hygienically. Consider the following when determining the amount of septic tank you require: septic tank sizes impact the overall effectiveness of your septic system; It is possible for wastewater to back up your house when the holding capacity of your septic tank is exceeded, producing clogs and floods, and placing you and your family in danger.

Septic system sizes for North Atlanta, GA homes may be determined by contacting us.

Homeowners!With any new septic tank installation, you’ll receive a Cutco knife gift with our thanks!

The amount of people living in your home determines the size of your septic tank. In the case of a two-person household, a modest septic tank will be required. A larger septic tank will be required if your house has more than five tenants, since this will allow you to handle your wastewater more effectively and hygienically. Consider the following when determining the amount of septic tank you require: septic tank sizes impact the overall efficiency of your septic system. When the holding capacity of your home’s septic tank is exceeded, wastewater can back up into your home, causing blockages, floods, and putting you and your family at risk.

Please get in touch with us to determine the optimal septic size for your North Atlanta, GA house.

Site and Soil Testing, Certifications for Septic Systems

Count on Sunset Septic to install your septic system in a professional and timely manner. We also provide quick site and soil testing for builders, banks, and lenders in order to establish whether or not a septic system (or systems) can be constructed on a particular piece of property. For complex septic repairs and needs, we collaborate with local plumbing businesses in Maricopa and Pinal counties to provide a comprehensive solution.

How much does a septic system cost? Let’s talk480-988-1401

For additional information on alternate options to traditional septic tanks for your residential or business property, please contact us now.

Dimension List – Arizona Precast Septic Concepts LLC

From the bottom of the tank to the bottom of the stub out, the outlet is 114 inches.

HOLE DIMENSIONS

15’10” in length, 8’10” in width 15.5 inches in length, 11 inches in width, and 10.5 inches in height

Other sizesavailable upon request

8′′X8′′ taper to 6.75′′X6.75′′6′ long x 6′′ tall x 8.5′′ wide 8′′X8′′ taper to 6.75′′X6.75′′ 47 inches in length, 5 inches in height, and 9 inches in width

Other sizes made upon request

24 inches inside diameter, 34 inches outside diameter

Welcome to Gila County

QUESTIONS ARE ASKED OF THE WASTEWATER DEPARTMENT ON A REGULAR BASIS. What is a septic system, and how does it work? What is a septic tank, and how does it work? As for the solid materials in the tank, what happens to them? Why should I keep my septic system in good working order? When should a tank be pumped and how often? What is the best way to find my septic tank? What is involved in pumping out a septic tank and how does it work? Who is in charge of pumping septic tanks? Do septic tank additives have any effect?

What is a cesspool, exactly?

What is the maximum distance my septic tank may be from.?
Can you recommend someone to design my on-site sewage treatment system?
An underground sewage treatment and disposal system, the septic system is composed of two parts that are buried in the earth.

The sewage is directed into the septic tank by gravity, where the particles separate from the liquid and are discarded.
The result is water that is clean and ready to re-enter the fresh water supply.
The standard septic tank is often a waterproof building made of concrete, fiberglass, or plastic, in which effluent from toilets, bathtubs, showers, laundry, and the kitchen is collected and treated.

This is known as the retention time.

The water part, also known as effluent, is forced out of the tank by gravity.

Return to the top of the page THE SOLID MATERIALS IN THE TANK EXPERIENCE WHAT HAPPENS?

Bacteria that can survive in the lack of oxygen break down a tiny portion of the solid material, with the remainder being evacuated from the tank by the pumping action of the pump.

Return to the top of the page WHY SHOULD I KEEP MY SEPTIC SYSTEM IN GOOD WORKING ORDER?

When indicators of breakdown appear, it is possible that costly repairs may be required.

Until a big indicator arises, such as surface sewage or back-ups into the residence, it is difficult to determine what is wrong with the system.

This is the most common cause of system failure and necessitates the installation of a new system. Maintenance Tips for a Healthier Septic System:

WHEN QUESTIONS ARE ASKED OF THE WASTEWATER DEPARTMENT, Septic systems are what they sound like. The term “septic tank” means “sewage treatment system.” In the tank, what happens to the solid materials? What are the benefits of keeping my septic system in good condition? Is it necessary to pump your tank on a regular basis? What is the best way to find my septic system? Pumping a septic tank involves several steps. Who is in charge of pumping out septic systems? Whether or not septic tank additives are beneficial. What is a drain field, and why do you need one. I’m not familiar with the term “cesspool.” When it comes to my septic tank, what should I not throw down the drains? What is the maximum distance between my septic tank and. Which type of sewage system would my property require and how can I find out? Who can help me with the design of my on-site sewage disposal system? CAN YOU EXPLAIN WHAT A SEPTIC SYSTEM IS? Sewage treatment and disposal systems are buried in the ground and consist of two parts: treatment and disposal. Septic tanks and soil drain fields are the two components of this system. Solids settle out of solution in the septic tank as a result of gravity pulling sewage into it. When the liquid, known as effluent, reaches the drain field, it soaks into the ground, where oxygen-breathing microorganisms devour and/or destroy any leftover sewage, bacteria, and viruses. The result is water that is clean and ready to re-enter the drinking water supply. Returning to the beginning CAN YOU EXPLAIN WHAT A SEPTIC TANK IS. The standard septic tank is often a waterproof building made of concrete, fiberglass, or plastic, in which effluent from toilets, bathtubs, showers, laundry, and kitchen sinks is gathered and processed. In order for the majority of heavy suspended solids, such as fecal matter, dirt, grit, and food residues, to sink to the bottom of the tank, the tank must retain the wastewater for an extended period of time. This is known as the retention time. At the same time, lighter elements such as oils, fats, and paper products float to the top of the tank, where they become stuck between the input and outflow pipe. It is pushed out of the tank, together with the water part. The effluent, which contains organic debris as well as high concentrations of bacteria and viruses, is dumped into an underground pipe system known as a drain field or leach field, depending on where it is located. Returning to the beginning THE SOLID MATERIALS IN THE TANK EXPERIENCE WHAT HAPPENS. In a tank, solid materials will eventually settle to the bottom or float to the top depending on their density. Microorganisms that can survive in the lack of oxygen decompose only a limited amount of solid material, with the remainder being removed from the tank by pumping the tank. Several biological materials disintegrate very slowly, but others, such as polymers and metals, as well as other inorganic materials, do not dissolve at all (see Figure 1). Returning to the beginning WHY SHOULD I KEEP MY SEPTIC SYSTEM IN GOOD WORKING ORDER. If you maintain your wastewater drain field on a regular basis rather than waiting for indicators of failure to appear, you will extend the life of the system. It is possible that costly repairs will be required if failure signals appear. Its “out of sight, out of mind” nature is the most significant barrier to proper septic tank care. Until a big indicator arises, such as surface sewage or back-ups into the home, it is difficult to determine what is wrong with the plumbing. If sludge and scum are not cleaned from the tank, they will build up, resulting in sewage particles being washed out into the drain field, where they will prematurely block the soil and choke the drain field. Maintaining a healthier septic system is the most common cause of system failure, and it almost always necessitates the replacement of the system.

Return to the top of the page A SEPTIC TANK SHOULD BE PUMPED ON A REGULAR BASIS. The frequency with which this is done is determined by the size of the tank and the number of people that live in the home. It is dependent on the overall daily flow as well as the amount of solids that enter the system. A general rule of thumb is that a residence with three people and a 1000-gallon tank should have its tank pumped every four years; with more occupants and larger tanks, this number may vary. Due in part to the unique behaviors of different families and the number of people in the family, some systems may not require maintenance for several years, while others may require it every two (2) years, depending on the kind of system.

Please refer to the pumping chart for information on the optimum time range for pumping your tank.

The following are the guidelines:Scum + Sludge “Scum3″/”Sludge12” refers to the 25-33 percent of tank volume that is below the outflow level.

To find out where your septic tank system is situated, call the Gila County Wastewater Division and ask whether or not your system is on their list of known septic tanks.

Some of the clues to the location of your septic system may be visible in your yard, such as pipes protruding from the ground, such as a two-way cleanout on one side of your house where the septic tank is located, an orange diverter valve after the septic tank, white inspection pipes at the end of each leach line, or indentations in the ground where excavation has taken place.

You can find contractors that are competent to locate your system on the Gila County Contractors List– Transfer of Ownership Inspectors.
Pumping a septic tank entails removing the tank’s lid and opening both manholes at the same time.

In order to be properly disposed of, the liquid/solid combination, known as septage, must be transported to an approved landfill or sewage treatment plant.
Return to the top of the page WHO IS IN CHARGE OF PUMPING SEPTIC TANKS?
Septic system products such as yeast, bacteria, enzymes, and chemicals are offered with the premise that they will improve the performance of septic systems.

It is also possible that sediments in an overcrowded tank will be re-dissolved in the effluent and carried into leach lines, resulting in blockage and premature failure of the system.
It is therefore necessary to do routine tank pumping to ensure that your system operates properly and to avoid early failure of your system.

Return to the top of the page WHAT IS A DRAIN FIELD AND HOW DOES IT WORK?

It serves as a filter and disinfectant, eliminating the majority of contaminants, disease-causing viruses, and bacteria present in the effluent before it reaches the environment.

The term “cesspool” refers to an excavation or non-watertight device that accepts untreated and water-carried liquid human waste from a house or business and allows it to be discharged directly into the soil.

A variety of papers, including Water Quality and Your Property Value and Gila County Cesspool Policy, might provide further information about properties where sewage disposal is handled by a cesspool.

Keep an eye on what you flush down the toilet!

Replacing it will cost between $3,000 and $12,000, depending on whether your site still qualifies for a standard septic system, and up to $30,000 if the soil and lot features necessitate the installation of an alternative system due to their unique qualities.

It is possible for hydraulic overload of the absorption field to occur due to very high water consumption from poor water fixtures and extremely large volumes of washing.

In addition to disrupting the biological activity in the tank, chemicals such as paint thinner, vehicle oil, and bleach poured down domestic drains can pollute the groundwater in your area and clog the soil pores in the absorption field.

Here are the setbacks that are most typically required from any element of your on-site wastewater system: Footings and foundations for a building Ten driveways and parking lots; five home water lines; five water mains; ten wells; one hundred feet.

Return to the top of the page WHAT IS THE BEST WAY TO DETERMINE WHAT KIND OF SEWAGE SYSTEM MY LOT WILL NEED?

Local private contractors that have completed soil testing and sewage treatment system design training as well as the Arizona On-site standards that regulate soil testing, sewage system design and installation conduct the tests.

In addition to the fees imposed by the private contractor, Gila County charges a fee of $150, which must be paid to the county.

Gila County will organize a soil test with the designated party on a mutually convenient date.

According to Gila County Ordinance01-2, septic systems may be designed by private contractors who have received training in soil testing, sewage treatment system design, and the Arizona On-site rules, which govern soil testing, sewage system design, and installation, as well as in the Arizona On-site rules and regulations.

Ordinance01-2 also requires that all alternative systems be designed by Arizona Registered Professional Engineers who are denoted by a * before their names in the same Designer Section of the Contractors List and installed by properly licensed Arizona Contractors who are listed in the Contractors Section of the Contractors List, as well as by properly licensed Arizona contractors who are listed in the Designer Section of the Contractors List.

Return to the top of the page

Septic System Installation & Alterations

Are you constructing a brand-new residence? Are you planning to add more bedrooms to your present residence? Is your present septic system on its last legs and in desperate need of replacement? Priority Pumping will provide you with a FREE ESTIMATE for any problem you are experiencing. The installation of traditional and advanced treatment septic systems is offered by Priority Pumping for new construction residences, additions, remodels, and whole sewage system replacements due to aged or failing systems.

Traditional septic systems are straightforward systems that consist of a septic tank and a leach field.
An advanced treatment system, also known as an ATU (Aerobic Treatment Unit), is a more complicated septic system in which the effluent is treated either before it enters the disposal field or with designed products within the leach field, depending on the situation.
Using our full-service permitting program, Priority Pumping can assist you in obtaining the necessary permits for your septic tank installation.
If you live in or around the Phoenix region, we are your one-stop shop for all of your septic tank installation needs.

Priority Pumping offers support through all stages of the installation process.

Perc testing is performed on the same day as the site evaluation.

Phase 2 Permitting

Construction and septic system design – both traditional and innovative – are examples of application.

Installation Service

Installation services for traditional and sophisticated treatment systems are provided on a turnkey basis.

Septic System Alterations

Permitting is necessary if you are replacing only the septic tank or the waste disposal field.

Abandonment/ Sewer Connections

In order to connect to public or private sewers, the septic system must be abandoned.

Phase I Permit Application – Site And Soil Testing (perc test)

The Phase I permits application entails filling out a form given by the County that contains a broad summary of the property as well as the designs for the new septic system, among other information. This permitting process necessitates the creation of a plot map of the planned house site in order to ensure that the correct setback criteria are satisfied while establishing the location of the septic system. If you aren’t sure where you want to place the house or if the testing is necessary in order for the bank to loan money on the land, we will choose a decent middle ground and conduct the testing there.

We’ll take care of submitting phase 1 tests to the County on your behalf.

It is necessary to undertake a site and soil test, which is also known as a perc test, as part of the initial Phase I permitting process.

The planned disposal field will have three locations: two in the proposed disposal field area and one in the proposed reserve disposal field.

(A full percolation test is performed in a slightly different manner than the sitesoils test; we’ll discuss this in more detail later.) We collaborate with a professional sanitarian who will do our site and soils examination on the same day as the hole excavation and report back to us the results.

This term refers to the rate at which water is absorbed by the soil once it has been injected, and it describes the fundamental constitution of soil properties.
Also included will be a site study based on the proposed plot map, which will guarantee that the needed setback dimensions are achievable with the planned home site.
Our sanitarian will complete the six-page report needed by the County and return it to us within 3-5 business days of receipt of the report.
If the results of the site and soil testing indicate that the circumstances for a normal conventional system are not appropriate, a comprehensive percolation test will need to be carried out.
If the location where you wish to build is already in a high-traffic area for necessary ATU systems, we will notify you and help you prepare for the test.

We constantly aim to save our clients money by doing the site and soils tests first, because in Arizona, conventional systems do not require full PERC tests.

Phase II Permit Application and Septic System Design

You must submit your septic system design to the county for approval before you can begin construction during this step of the permitting procedure. It is necessary to complete this step in order to pick the appropriate septic tank size and create the most appropriate disposal strategy based on the SAR number that was supplied in Phase I. The selection of the appropriate septic tank size is accomplished in one of two methods, with thorough consideration given to both in detailed calculations.

(This includes garage sinks, barns, pool baths, guest quarters, and other similar facilities.) Each plumbing fixture in the house is assigned a number based on the amount of water it takes to run it properly.
On a calculation sheet, all of the fixtures are put together, and a grand total of “fixtures” is noted down.
Dens may be used as bedrooms in some circumstances, however this is not always the case.
A new home may be built with the intention of adding an expansion or constructing a garage/workshop in the near future, which is common.
Although the system appears to be a little too large for the existing property, this will save the need for septic system re-construction in the future if the new rooms or fixtures exceed the permitted limit.

Check out the links here to help you understand the process.

It is necessary, in addition to determining the appropriate septic tank size, to determine the complexity of the disposal field by multiplying the number of bedrooms/fixtures in your home by the SAR number acquired during Phase I-Site and Soil testing. Seepage pit(s), leach lines, and chamber systems are the most popular types of traditional septic system disposal fields in the state of Arizona. Each disposal field is extremely distinct from the others, and each is employed for a different set of requirements and applications than the others.

If your soils test results indicate that you need an advanced treatment unit, we can advise you on the most appropriate system for your house, its intended use, and its maintenance needs.
Proper septic system design will ensure that you have a system that will last you for many years and will do its job effectively every time.
In order to begin the installation procedure, this is the signal that must be sent.
Our service covers the completion of all applications, the collecting of all essential documents, the creation of comprehensive scaled site plans, the scheduling of inspections, and other services as needed.

We’ve put in the time and effort to learn everything we can about the permits and how to get them completed as fast as possible. Allow us to assist you right now!

Full Septic Installation Service

We can arrange your installation project to begin as soon as the County has granted the Approval for Construction document. With county inspections, most systems may be implemented in one to two weeks, depending on the complexity of the system. In order to complete this massive operation, our installation crew will utilize our own excavation equipment, which we will have completely licensed and insured. Our installation crew has years of combined expertise and is comprised of some of the nicest men you’ll ever come across.

After that is completed, the two halves of the system are linked together using the appropriate plumbing and connections to form a whole.
The final construction of the septic system is typically inspected by a representative within 48 hours of it being completed before any component of the system is covered up.
That’s all there is to it!
Your permission package, which includes all necessary documentation for your files, as well as a maintenance manual for your system, will be delivered to you at the completion of your project.

Septic System Alterations

It is critical to understand that a septic system is comprised of two equally significant components: the septic tank and the disposal field (or leach field). In the event that one or more sections of a septic system have failed and need to be changed, this is known as a septic system modification. The following are examples of situations in which a change may be necessary:

As long as the septic tanks are not damaged beyond repair and the disposal field is still in good working order, you may just need to replace the septic tanks
Otherwise, you may need to replace the disposal field as well. If the disposal field is over-saturated or the structure is damaged beyond repair, but the septic tank is still operational, you may just be required to replace the disposal field
However, this is not always the case.

If the septic tank and disposal field are no longer operational, the entire system must be abandoned, and you will be required to go through the full installation procedure again from scratch. Do you have any questions? Please contact us! 602-601-5751 We wish to be of assistance to you! When applying for an Alterations Permit for a septic tank, there are a few points on your checklist that you should keep in mind. As long that the home is the same size (in terms of bedroom count) as the previous system was approved for, you may simply submit a modifications permission to replace the septic tanks with like-for-like ones.

Through the use of a Report of Inspection form, we will need to identify the specific disposal field technique, as well as the size and functioning of the disposal field, before moving forward.

This would provide us with a SAR number that we could use to compute the new field.

Given that this is such a unique circumstance, Priority Pumping is delighted to conduct a little background study on your initial permitting procedure in order to provide you with the most accurate quote possible for your modification.

Septic System AbandonmentSewer Connection

If the septic tank and disposal field are no longer functional, the entire system must be abandoned, and you will be required to go through the full installation procedure again from scratch. Question? Please ask it below. Dial our number to speak with one of our friendly representatives. 602-601-5751 This is something we are interested in doing for you! When applying for an Alterations Permit for your septic tank, there are a few things you should keep in mind. It is not necessary to get an alterations permission to switch out like-for-like septic tanks if the residence is still the same size (in terms of bedroom count) as the original system was approved for.

Through the use of a Report of Inspection form, we will need to ascertain the specific disposal field technique, as well as the size and functioning of the disposal field.

In order to calculate the new field, we would need a SAR number.

We understand that every circumstance differs, and we are delighted to conduct some preliminary study into your initial permission procedure in order to provide you with the most accurate quote possible for your modification.

Some portions of a system may only require partial dismantling in some cases. This is referred to as a septic system change, and it was previously described. If you are simply modifying the tank or the field, you will only be required to abandon the component of the system that is being replaced
If you are replacing the complete septic system, you will be required to leave the entire system. Whether you are leaving a full failure system, upgrading to a larger system, or deciding to connect to the city sewage, you will find yourself in this predicament.

There are two methods for completing the abandonment process. We may either slurry or dirt fill the septic tank and field, or we can completely remove the tank and field system. We will advise you on the best course of action for your individual scenario. If your septic system fails and there is a sewage line in close proximity to your property, you may be required to connect to the sewer system according to local regulations. The counties of Maricopa and Pinal are expanding at a fast rate. What a shocker to learn that Maricopa County has been the nation’s fastest expanding county for three years in a row!

Some of these capital improvement projects include the installation of new sewage lines across septic communities that are over 100 years old.
You can get assistance with this procedure from Priority Pumping.
Contact us now.
For further information, please contact us at 602-601-5751.

More information can be found at Due to the fact that I had a septic system that did not pass inspection, plus the fact that I was a Realtor, I was having difficulty getting some septic work completed.

Priority Pumping came to my attention by chance.
They completed all of the tasks they had promised, and they did it in a timely way.
We did the project on schedule, and everyone was pleased with the results.
I want to utilize them again whenever the opportunity arises.
Because it was a Friday, I had anticipated having to wait until Monday, but when I indicated that it was an emergency, they squeezed me into their schedule and arrived exactly on schedule.
You may rest assured that you will have my business in the future!
Jeff Stanley is an American actor and director who was born in the United States.

More information can be found at While working in an industry that frequently stinks (no pun intended), Tanya and her colleagues are extraordinary.

Professionalism, promptness, and a high level of communication distinguish the pros from the other amateurs out there who don’t return calls or, even worse, don’t show up to the task that you’ve hired them to accomplish on your behalf.

Tanya, thank you for being who you are!

Excellent communication skills.

They communicated with us throughout the process, arrived on time, and completed the work in a professional and quick manner. I would strongly suggest them to anyone who is searching for a professional organization.

Servicing Commercial and Residential Locations Across the Valley, Including:

Our services range from simple septic tank design to intricate alternative systems, including permits, engineering, and septic system installation. Contact us now to learn more. We are a full-service turnkey contractor that can also provide servicing once the installation is complete, if necessary. We also provide full-service septic tank pumping and septic cleaning in the following Arizona cities:Phoenix (including Scottsdale and Cave Creek), Carefree (including Anthem and Fountain Hills), Glendale (including Peoria) and Peoria (including Surprise and Waddell), Tempe (including Gilbert and Chandler), and many others.

We can handle any and all of your septic tank or waste system requirements.
We are licensed and insured by the state of Arizona.
As a leading service provider, Arizona Septic Tank is well-equipped to manage your excavation and septic tank dig as well as leach trenching and, in certain cases, septic leach drilling.
You can rely on us to provide dependable services that get the job done effectively.
Leave the task in the hands of our professionals for the sake of your residence or place of business.

What do I need to know about my septic tank?

We are here to answer any questions you may have concerning your septic tank, as well as to assist you in understanding how and when it should be maintained. Here are some of the most commonly asked questions we receive, to assist you in better understanding the process!

Arizona Septic Tank Services

All of our repair, inspection, and maintenance services are accessible around the clock, and we are always happy to answer any questions or concerns. We are delighted to answer any questions you may have and assist you in establishing exactly what it is that you want. Whether you require an expert immediately or simply have a question, please contact us. In addition to providing high-quality, professional septic services, we also provide services in the following areas:

A comprehensive septic pumping and cleaning
A grease trap pumping and cleaning
A septic tank inspection for home sales
Any and all necessary repairs (no matter how little)
Cleaning, replacement, and installation of the effluent filter are all included in this price. Therapy with enzymes
Treatment with roots
Installation of a service port and electronic position

A State Inspection Report detailing the condition of a septic system must be sent to the buyer if you are selling a property that is linked to a septic system, as required by law. For further information, please contact us. Is There a Process Going On in My Septic Tank? Your septic tank is the starting point for the wastewater treatment process, owing to the optimum circumstances that exist in the tank that allow bacteria to flourish and flourish. Almost any organic waste is consumed as food by the bacteria, which collects at the bottom of the tank as’sludge.

Any gases that are created as a result of this liquefaction are expelled through particular vents in the plumbing.
According to the Department of Environmental Quality’s requirements, we recommend that you get your tank pumped every 3 – 5 years.
What if I don’t have any problems with my tank?
Yes, if you want your tank to last a long time.
4.
Don’t get too worked up over it!
Inspect the water level in your “P” traps, check the seals around the bases of your toilets, and sprinkle soil over the top of your septic tank cover to filter out any gas odours that may be generated from the tank itself.

My toilets have become clogged.

First and foremost, call us!

Is it normal for my toilet to make unusual gurgling noises?

Ensure that your kitchen and bathroom sinks are free of obstructions if your toilet gurgles while being flushed or refilled.

There might be a clog in the sewage line, your tank could be overflowing, or the entire system could be malfunctioning.

We provide you with helpful suggestions to assist you remember what you should and should not send through your septic tank.

Maintain a close eye on all leaks and make certain that roof drains and sump pumps are routed away from the septic system.

The use of bleach in the laundry on occasion, as well as the use of most household cleaners, is OK; nevertheless, it is a good idea to check the labels to verify that they will not cause harm to the septic system. It is best not to flush any of the following objects through the plumbing system:

The following items are prohibited: coffee grounds, sanitary pads, dental floss, tampon applicators, diapers, cigarette butts, condoms, bandages, fat and oil.

I’m inviting a large number of folks to stay. Is it necessary for me to be concerned about my septic tank system? A large gathering is a good time to get your septic tank repaired, as the tank might become overcrowded as a result of the high volume of people. An emergency pump service would be required, which would be both costly and stressful; instead, arrange a pump service ahead of time so that you don’t have to worry on the big day! Is it necessary for me to add more therapies to the system?

It is incredibly simple to incorporate a bacteria treatment into your system — the treatment may simply be flushed down the toilet.

This is particularly good if you have recently had extensive cleaning done in your home, which included the use of harsh chemicals, or if someone in your household has become severely unwell.

Arizona Septic Tank, a full service septic system service company

My guests will number in the hundreds. Are there any issues with my septic tank system that I should be concerned about? A large gathering is a good time to get your septic tank repaired since the tank might become overloaded if it is overworked. An emergency pump service would be required, which would be both costly and stressful; instead, arrange a pump service ahead of time so that you don’t have to worry on the big day itself. Whether or whether I should supplement the system is up to me.

It is incredibly simple to incorporate a bacterium treatment into your system – the treatment may simply be flushed away.

In particular, if you have recently had substantial cleaning done in your home with harsh chemicals, or if you or a member of your family has been unwell, this can be really beneficial.

Standard Conventional Septic Systems

Generally speaking, there are two types of typical standard systems: those that integrate chambers and those that will employ a gravel basis in the drain field. Traversing at least 3 feet deep and laying out leach rock in the trenches to aid in proper sewage / waste water drainage are typical features of a conventional gravel system. The term “leach rock” refers to the leach rock that is laid out in the trenches to aid in proper sewage / waste water drainage. The standard chamber type is one of the more recent and more suited methods; septic systems that employ chambers instead of leach stones are becoming increasingly popular among septic installers and septic tank contractors.

The same test is used to assess the depth of the trenches, as well as the size and number of bedrooms, bathrooms, and drains that are present in your property.
In most cases, the usual tank capacity will be between 1250 and 1500 gallons, although this can climb to as much as 3000 gallons for bigger houses or workplaces.
However, the majority of the treatment will take place in the waste water that is discharged from the tank into the leach field or leach chambers that are installed in the trenches below ground, as described above.
Over time, organisms and bacteria will eat any organic debris that is present in the waste water stream itself.

Biomat is a layer formed by organisms that forms over time and in the presence of significant oxygen allows parasites and worms to feed on the micro bacteria, resulting in an extremely thick biomat barrier that prevents waste water from penetrating into the soil below.

Alternative Septic System

Systems that integrate chambers and those that employ a gravel basis in the drain field are the two types of typical standard systems that are now available. Traversing at least 3 feet deep and laying down leach rock in the trenches to aid in appropriate sewage / waste water drainage are typical features of a traditional gravel system. The term “leach rock” refers to the leach rock that is used in the trenches to aid in adequate sewage / waste water drainage. Modern septic systems that employ chambers instead of leach stones are becoming increasingly popular with both residential and commercial septic system installers and septic tank contractors.

To establish the length and number of trenches required for installation of the chambers, the trenches are built and engineered according on soil characteristics and perk rate.

The installation of a standard septic tank will also need the selection of the appropriate septic tank for your project.

Initially, waste treatment takes place in the tank itself, with bacteria eating away at waste and the solids settling to the bottom of the tank.

Filtration of waste water occurs in the leach fields, which are filtered by leach rock and/or the ground dirt.

The organisms produce a layer known as a biomat, which builds up over time and with sufficient oxygen will allow parasites and worms to feed on the micro bacteria, resulting in a thick biomat barrier that prevents waste water from penetrating into the soil below.

Septic System Plumbing Advice

Plumbing Guidance for Your Home Improvement Projects This is your greatest opportunity to obtain a more comprehensive grasp of septic system plumbing. It is critical that you study as much as you can today, before any problems arise in the future. Make use of the excellent suggestions offered in this article.