What Is An Inground Septic Tank? (Solved)

Underground septic tanks are also referred to as sewer tanks, below ground septic tanks, waste holding tanks, cesspool tanks, cesspits, bulk sewage tanks, and black water tanks. They are used to contain human waste, sewage, and blackwater.

• The tank is located in the ground and is usually made of concrete where blackwater from toilets and greywater from sinks and showers flow into it. In the tank, the solids sink to the bottom and the fluid drains into a series of underground pipes laid out in a grid on the property.

What is an inground septic system?

Septic Tank A buried, watertight tank designated and constructed to receive and partially treat raw domestic sanitary wastewater. Heavy solids settle to the bottom of the tank while greases and lighter solids float to the top.

Are septic tanks completely buried?

Depending on your septic tank setup, your system may include two or three lids. Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

What are the 2 types of septic systems?

There are two basic septic system types — conventional and alternative. Site and soil conditions generally determine the type of system that should be installed.

What is the difference between a septic tank and a septic field?

The septic tank is a buried, water-tight container usually made of concrete, fiberglass, or polyethylene. The liquid wastewater (effluent) then exits the tank into the drainfield. The drainfield is a shallow, covered, excavation made in unsaturated soil.

Does shower water go into septic tank?

From your house to the tank: Most, but not all, septic systems operate via gravity to the septic tank. Each time a toilet is flushed, water is turned on or you take a shower, the water and waste flows via gravity through the plumbing system in your house and ends up in the septic tank.

What are the signs that your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

• Your Drains Are Taking Forever.
• Standing Water Over Your Septic Tank.
• Bad Smells Coming From Your Yard.
• You Hear Gurgling Water.
• You Have A Sewage Backup.
• How often should you empty your septic tank?

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Can you sell a house with an old septic tank?

If you’re selling a property with a septic tank, then you must be transparent with buyers about the fact the property uses a one and provide a detailed specification of the system. In fact, You are required by law to inform a buyer in writing about the presence of a septic tank.

How deep is a septic tank usually buried?

Often, septic tank lids are at ground level. In most cases, they have buried anywhere from four inches to four feet underground. If you’ve just bought the home and you don’t know where your septic tank is located, this guide will provide information on how to find your septic tank.

How big of a septic tank do I need?

The larger your home, the larger the septic tank you’re going to need. For instance, a house smaller than 1,500 square feet usually requires a 750 to 1,000-gallon tank. On the other hand, a bigger home of approximately 2,500 square feet will need a bigger tank, more than the 1,000-gallon range.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

What to do after septic is pumped?

After you have had your septic tank pumped by a trusted septic company, there are some things you can and should do as the septic system owner.

1. 1) Get on a Schedule.
2. 2) Take Care of the System.
3. 3) Know the Parts of Your System.
4. 4) Check Other Possible Issues.

How often should a septic tank be pumped?

Inspect and Pump Frequently Household septic tanks are typically pumped every three to five years.

Are septic tanks safe?

Never work alone in or around a septic tank. Don’t ignite flames or smoke cigarettes at or near the tank. This can cause an explosion. Be sure that the tank and its access ports have sound and secure covers that do not risk collapse and which cannot be removed or nudged aside by children or animals.

Can you walk on a septic mound?

Low-maintenance perennial plants that minimize the need to walk on the mound are ideal. Walking compacts the soil and may interfere with the evaporation of effluents. Do as little digging as possible when planting to avoid disturbing the mound and be sure to wear gloves to minimize your physical contact with the soil.

Types of Septic Systems

Septic system design and size can differ significantly from one neighborhood to the next, as well as throughout the country, due to a variety of variables. Household size, soil type, slope of the site, lot size, closeness to sensitive water bodies, weather conditions, and even municipal ordinances are all considerations to take into consideration. The following are 10 of the most often encountered septic system configurations. It should be noted that this is not an exhaustive list; there are several additional types of septic systems.

• Septic Tank, Conventional System, Chamber System, Drip Distribution System, Aerobic Treatment Unit, Mound Systems, Recirculating Sand Filter System, Evapotranspiration System, Constructed Wetland System, Cluster / Community System, etc.

Septic Tank

This tank is underground and waterproof, and it was designed and built specifically for receiving and partially treating raw home sanitary wastewater. Generally speaking, heavy materials settle at or near the bottom of the tank, whereas greases and lighter solids float to the surface. The sediments are retained in the tank, while the wastewater is sent to the drainfield for further treatment and dispersion once it has been treated.

Conventional System

Septic tanks and trench or bed subsurface wastewater infiltration systems are two types of decentralized wastewater treatment systems (drainfield). When it comes to single-family homes and small businesses, a traditional septic system is the most common type of system. For decades, people have used a gravel/stone drainfield as a method of water drainage. The term is derived from the process of constructing the drainfield. A short underground trench made of stone or gravel collects wastewater from the septic tank in this configuration, which is commonly used.

Effluent filters through the stone and is further cleaned by microorganisms once it reaches the soil below the gravel/stone trench, which is located below the trench.

Chamber System

Gravelless drainfields have been regularly utilized in various states for more than 30 years and have evolved into a standard technology that has mostly replaced gravel systems. Various configurations are possible, including open-bottom chambers, pipe that has been clothed, and synthetic materials such as expanded polystyrene media. Gravelless systems can be constructed entirely of recycled materials, resulting in considerable reductions in carbon dioxide emissions during their lifetime. The chamber system is a type of gravelless system that can be used as an example.

The key advantage of the chamber system is the enhanced simplicity with which it can be delivered and built.

This sort of system is made up of a number of chambers that are connected to one another.

Wastewater is transported from the septic tank to the chambers through pipes. The wastewater comes into touch with the earth when it is contained within the chambers. The wastewater is treated by microbes that live on or near the soil.

Drip Distribution System

An effluent dispersal system such as the drip distribution system may be employed in a variety of drainfield configurations and is very versatile. In comparison to other distribution systems, the drip distribution system does not require a vast mound of dirt because the drip laterals are only placed into the top 6 to 12 inches of soil. In addition to requiring a big dosage tank after the sewage treatment plant to handle scheduled dose delivery of wastewater to drip absorption areas, the drip distribution system has one major disadvantage: it is more expensive.

Aerobic Treatment Unit

Aerobic Treatment Units (ATUs) are small-scale wastewater treatment facilities that employ many of the same procedures as a municipal sewage plant. An aerobic system adds oxygen to the treatment tank using a pump. When there is an increase in oxygen in the system, there is an increase in natural bacterial activity, which then offers extra treatment for nutrients in the effluent. It is possible that certain aerobic systems may additionally include a pretreatment tank as well as a final treatment tank that will include disinfection in order to further lower pathogen levels.

ATUs should be maintained on a regular basis during their service life.

Mound Systems

Using mound systems in regions with short soil depth, high groundwater levels, or shallow bedrock might be a good alternative. A drainfield trench has been dug through the sand mound that was erected. The effluent from the septic tank runs into a pump chamber, where it is pumped to the mound in the amounts recommended. During its release to the trench, the effluent filters through the sand and is dispersed into the native soil, where it continues to be treated. However, while mound systems can be an effective solution for some soil conditions, they demand a significant amount of land and require regular care.

Recirculating Sand Filter System

Sand filter systems can be built either above or below ground, depending on the use. The effluent is discharged from the septic tank into a pump compartment. Afterwards, it is pushed into the sand filter. The sand filter is often made of PVC or a concrete box that is filled with a sand-like substance. The effluent is pushed through the pipes at the top of the filter under low pressure to the drain. As the effluent exits the pipelines, it is treated as it passes through the sand filtering system.

However, sand filters are more costly than a standard septic system because they provide a higher level of nutrient treatment and are thus better suited for areas with high water tables or that are adjacent to bodies of water.

Evapotranspiration System

Evaporative cooling systems feature drainfields that are one-of-a-kind. It is necessary to line the drainfield at the base of the evapotranspiration system with a waterproof material. Following the entry of the effluent into the drainfield, it evaporates into the atmosphere. At the same time, the sewage never filters into the soil and never enters groundwater, unlike other septic system designs. It is only in particular climatic circumstances that evapotranspiration systems are effective. The environment must be desert, with plenty of heat and sunshine, and no precipitation.

Constructed Wetland System

Construction of a manufactured wetland is intended to simulate the treatment processes that occur in natural wetland areas. Wastewater goes from the septic tank and into the wetland cell, where it is treated. Afterwards, the wastewater goes into the media, where it is cleaned by microorganisms, plants, and other media that eliminate pathogens and nutrients. Typically, a wetland cell is constructed with an impermeable liner, gravel and sand fill, and the necessary wetland plants, all of which must be capable of withstanding the constant saturation of the surrounding environment.

As wastewater travels through the wetland, it may escape the wetland and flow onto a drainfield, where it will undergo more wastewater treatment before being absorbed into the soil by bacteria.

Cluster / Community System

In certain cases, a decentralized wastewater treatment system is owned by a group of people and is responsible for collecting wastewater from two or more residences or buildings and transporting it to a treatment and dispersal system placed on a suitable location near the dwellings or buildings. Cluster systems are widespread in settings like rural subdivisions, where they may be found in large numbers.

How Your Septic System Works

Underground wastewater treatment facilities, known as septic systems, are often employed in rural regions where there are no centralized sewage lines. They clean wastewater from residential plumbing, such as that produced by bathrooms, kitchen drains, and laundry, by combining natural processes with well-established technology. A conventional septic system is comprised of two components: a septic tank and a drainfield, often known as a soil absorption field. It is the septic tank’s job to decompose organic matter and to remove floatable stuff (such as oils and grease) and solids from wastewater.

Alternate treatment systems rely on pumps or gravity to assist septic tank effluent in trickling through a variety of media such as sand, organic matter (e.g., peat and sawdust), constructed wetlands, or other media to remove or neutralize pollutants such as pathogens that cause disease, nitrogen, phosphorus, and other contaminants.

Prior to discharging wastewater into the environment, several alternative systems are designed to evaporate or disinfect the effluent.

Specifically, this is how a typical conventional septic system works:

1. All of the water that leaves your home drains down a single main drainage pipe and into a septic tank. An underground, water-tight container, often composed of concrete, fiberglass, or polyethylene, serves as a septic system’s holding tank. Its function is to retain wastewater for a long enough period of time to allow particles to sink to the bottom and form sludge, while oil and grease float to the surface and produce scum. Sludge and scum are prevented from exiting the tank and moving into the drainfield region by compartments and a T-shaped outlet. After that, the liquid wastewater (effluent) exits the tank and flows into the drainfield. The drainfield is a shallow, covered hole dug in unsaturated soil that serves as a drainage system. Porous surfaces are used to release pretreated wastewater because they allow the wastewater to pass through the soil and into the groundwater. In the process of percolating through the soil, wastewater is accepted, treated, and dispersed by the soil, finally discharging into groundwater. Finally, if the drainfield becomes overburdened with too much liquid, it can flood, causing sewage to flow to the ground surface or resulting in toilet backups and sink backups. Finally, wastewater percolates into the soil, where it is naturally removed of harmful coliform bacteria, viruses, and nutrients. Coliform bacteria are a kind of bacteria that may be found in the intestines of humans and other warm-blooded animals, with humans being the most common host. As a result of human fecal contamination, it is a sign of this.

The Guadalupe-Blanco River Authority has built an animated, interactive model of how a residential septic system works, which you can view here.

Do you have a septic system?

It’s possible that you’re already aware that you have a septic system. If you are not sure, here are some tell-tale symptoms that you most likely are:

• You make use of well water. In your home, the water pipe that brings water into the house does not have a meter. In the case of a water bill or a property tax bill, you will see “$0.00 Sewer Amount Charged.” It is possible that your neighbors have a septic system

How to find your septic system

You can locate your septic system once you have confirmed that you have one by following these steps:

• Taking a look at the “as constructed” drawing of your house
• Making a visual inspection of your yard for lids and manhole covers
• Getting in touch with a septic system service provider for assistance in locating it

Failure symptoms: Mind the signs!

A bad odor is not necessarily the first indicator of a septic system that is failing to work properly. Any of the following signs should prompt you to seek expert assistance:

• Water backing up into the drains of homes and businesses
• It is especially noticeable in dry weather that the drainfield grass is bright green and spongy. The presence of standing water or muddy soil near your septic system or in your basement
• A strong stench emanating from the area surrounding the septic tank and drainfield

Underground Septic Holding Tanks

Protankprovides the highest-quality polyethylene plastic below-ground storage tanks available on the market today, including: Below-ground septic tanks are available in capacities ranging from 200 to 1500 gallons. Our plastic septic tanks are built to last and are intended for quick and simple installation. In addition, because our plastic septic tanks are composed of polyethylene, they are resistant to soil chemicals as well as to the chemicals and gases contained in sewage, which means that our plastic septic tanks will not rust or corrosion.

• We also provide pre-plumbed septic tanks, which are pre-plumbed in accordance with state regulations.
• Tanks that have been PRE-PLUMBED are sent to you ready to be installed.
• Tees are measured and cut to meet the requirements of each state code, ensuring that the tank you get is ready for installation.
• If you want assistance in selecting the most appropriate septic tank for your needs, our sales staff would be happy to assist you.

How Does a Septic Tank Work?

Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.

How does a septic tank work?

Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.

It’s critical to understand how a septic tank works in order to maintain one.

Let’s take a look below ground and observe what happens in a properly operating septic system, shall we? After that, I’ll explain why things go wrong and offer you some tips on how to keep your system in peak operating condition.

Understand that a septic system is a cafeteria for bacteria

Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.

• A layer of sludge settles to the bottom of the container.
• 4.
• Scum is mostly constituted of fats, greases, and oils, among other substances.
• Grease and oils float to the surface of the water.
• (5) A filter stops the majority of particles from reaching the exit pipe.
• The effluent is discharged into the drain field.
• Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.
• The garbage is completely decomposed by aerobic bacteria found in gravel and dirt.
• Potable water seeps into the groundwater and aquifer system from the surface.

Septic Tank Clean Out: Don’t abuse the system

Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank. However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.

• Drains are used to dispose of waste that decomposes slowly (or not at all). Cigarette butts, diapers, and coffee grounds are all known to cause issues. Garbage disposers, if utilized excessively, can introduce an excessive amount of solid waste into the system. Lint from synthetic fibers is emitted from washing machine lint traps. This substance is not degraded by bacteria in the tank and drain septic field. Bacteria are killed by chemicals found in the home, such as disinfecting cleansers and antibacterial soaps. The majority of systems are capable of withstanding limited usage of these goods, but the less you use them, the better. When a large amount of wastewater is produced in a short period of time, the tank is flushed away too quickly. When there is too much sludge, bacteria’s capacity to break down waste is reduced. Sludge can also overflow into the drain field if there is too much of it. Sludge or scum obstructs the flow of water via a pipe. It is possible for tree and shrub roots to obstruct and cause harm to a drain field. Compacted soil and gravel prevent wastewater from seeping into the ground and deprive germs of oxygen. Most of the time, this is caused by vehicles driving or parking on the drain field.

Get your tank pumped…

Your tank must be emptied on a regular basis by a professional. Pumping eliminates the accumulation of sludge and scum that has accumulated in the tank, which has caused the bacterial action to be slowed. If you have a large tank, it may be necessary to pump it once a year; but, depending on the size of your tank and the quantity of waste you send through the system, you may go two or three years between pumpings. Inquire with your inspector about an approximate guideline for how frequently your tank should be pumped.

…but don’t hire a pumper until you need it

Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.

Install an effluent filter in your septic system

Garbage from your home accumulates into three distinct strata.

The septic filter is responsible for preventing blockage of the drain field pipes.

Septic tank filter close-up

The septic tank filter is responsible for capturing suspended particles that may otherwise block the drain field pipes. Obtain an effluent filter for your tank from your contractor and place it on the outflow pipe of your tank. (It will most likely cost between $50 and $100, plus labor.) This device, which helps to prevent sediments from entering the drain field, will need to be cleaned out on a regular basis by a contractor to maintain its effectiveness.

Solution for a clogged septic system

If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.

1. Keep the effluent filter in place since it is required by your state’s health law.
2. Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
3. Your filter, on the other hand, should not require cleaning every six months.
4. A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
5. A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
6. Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.
7. More information on removing lint from your laundry may be found here.

Get an inspection

Following a comprehensive first check performed by an expert, regular inspections will cost less than $100 each inspection for the next year. You will be able to find out how a septic tank works from a professional, as well as how often your system should be inspected. As simple as a septic system may appear, determining its overall health requires the expertise of a professional. There are a plethora of contractors who would gladly pump the sludge out of your tank, but many, in my experience, are unable to explain how a septic system works or how it should be maintained.

The Secretary of State’s office can tell you whether your state has adopted certification programs for septic contractors; check with them to see if yours is one of them.

The tank’s capacity for your household will also be determined by a professional inspector, as will the maximum amount of water that can be sent through it in a day.

Adding bacteria to your system, such as with RID-X, may be able to boost the function of the entire system. As you learn more about how a septic tank works, your professional should be able to tell you whether or not your system will benefit from this treatment.

Alternatives to a new drain field

If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.

• Pipes should be cleaned. A rotating pressure washer, used by a contractor, may be used to clean out the drain septic field pipes. The cost of “jetting” the pipes is generally around $200. Chemicals should be used to clean the system. A commercial solution (not a home-made one) that enhances the quantity of oxygen in the drain field should be discussed with your contractor before installing your new system. Septic-Scrub is a product that I suggest. A normal treatment will cost between $500 and $1,000. Make the soil more pliable. The practice of “terra-lifting,” which involves pumping high-pressure air into several spots surrounding the drain field, is authorized in some regions. Some contractors use it to shatter compacted dirt around the pipes. Depending on the circumstances, this might cost less than $1,000 or as much as $4,000 or more.

Protect your drain septic field from lint

When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.

Don’t overload the septic system

Reduce the amount of water you use. The volume of water that flows into your tank, particularly over a short period of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to save water.

Meet the Expert

Septic systems, according to Jim vonMeier, are the solution to America’s water deficit because they supply cleaned water to depleted aquifers, according to vonMeier. He travels the country lobbying for septic systems, giving lectures, and giving testimony. For septic system inquiries, as well as information on the operation of the septic tank, contact him by email.

Septic Tank Installation and Pricing

To process and dispose of waste, a septic system has an underground septic tank constructed of plastic, concrete, fiberglass, or other material that is located beneath the earth. Designed to provide a customized wastewater treatment solution for business and residential locations, this system may be installed anywhere. Although it is possible to construct a septic tank on your own, we recommend that you hire a professional to do it owing to the amount of skill and specific equipment required.

Who Needs a Septic Tank?

For the most part, in densely populated areas of the nation, a home’s plumbing system is directly connected to the municipal sewer system. Because municipal sewer lines are not readily available in more rural regions, sewage must be treated in a septic tank. If you’re moving into a newly constructed house or onto land that doesn’t already have a septic tank, you’ll be responsible for putting in a septic system on your own.

How to Prepare for Your Septic Tank Installation

Here are a few pointers to keep in mind to make sure your septic tank installation goes as smoothly as possible.

Receive Multiple Estimates

Here are a few pointers to keep in mind to make sure your septic tank installation goes successfully.

Test the Soil and Obtain a Permit

For septic systems to function properly, permeable soil surrounding the tank must absorb and naturally handle liquid waste, ensuring that it does not pollute runoff water or seep into the groundwater. The drain or leach field is the name given to this region. Before establishing a septic tank, you are required by law to do a percolation test, sometimes known as a “perc” test. This test indicates that the soil fits the specifications established by the city and the local health agency. In most cases, suitable levels of permeable materials, such as sand or gravel, are necessary in a soil’s composition.

Note: If you wish to install a septic tank on your property, you must first ensure that the ground passes the percolation test. Prior to acquiring the land that you want to utilize for residential purposes, we recommend that you obtain a soil test.

Plan for Excavation

Excavation of the vast quantity of land required for a septic tank necessitates the use of heavy machinery. If you are presently residing on the property, be careful to account for landscaping fees to repair any damage that may have occurred during the excavation process. Plan the excavation for your new home at a period when it will have the least influence on the construction process if you are constructing a new home. Typically, this occurs before to the paving of roads and walkways, but after the basic structure of the home has been constructed and erected.

The Cost of Installing a Septic Tank

There are a few installation charges and additional expenditures connected with constructing a new septic system, ranging from a percolation test to emptying the septic tank and everything in between.

Percolation Test

A percolation test can range in price from $250 to $1,000, depending on the area of the property and the soil characteristics that are being tested. Ordinarily, specialists will only excavate a small number of holes in the intended leach field region; however, if a land study is required to identify where to excavate, the cost of your test may rise.

Building Permit Application

A permit will be required if you want to install a septic tank on your property. State-by-state variations in permit prices exist, however they are normally priced around $200 and must be renewed every few years on average.

Excavation and Installation

When you have passed a percolation test and obtained a building permit, your septic tank is ready to be professionally placed. The cost of a new septic system is determined by the size of your home, the kind of system you choose, and the material used in your septic tank. The following is a list of the many treatment methods and storage tanks that are now available, as well as the normal pricing associated with each.

Types of Septic Tank Systems

Septic system that is used in the traditional sense Traditionally, a septic system relies on gravity to transport waste from the home into the septic tank. Solid trash settles at the bottom of the sewage treatment plant, while liquid sewage rises to the top. Whenever the amount of liquid sewage increases over the outflow pipe, the liquid waste is discharged into the drain field, where it continues to disintegrate. This type of traditional septic system is generally the most economical, with an average cost of roughly $3,000 on the market today.

Drain fields for alternative systems require less land than conventional systems and discharge cleaner effluent.

Septic system that has been engineered A poorly developed soil or a property placed on an uphill slope need the installation of an engineered septic system, which is the most difficult to install.

It is necessary to pump the liquid waste onto a leach field, rather than depending on gravity to drain it, in order to ensure that it is equally dispersed across the land. The average cost of these systems is roughly $8,000.

Types of Septic Tanks

• Concrete septic tanks are long-lasting and rust-proof, but they are difficult to repair if they are damaged. It is possible that concrete tanks will cost up to $2,000 depending on their size. Plastic —While plastic tanks are cost-effective, they are also susceptible to damage. They are around $1,200 in price. Fiberglass —While fiberglass septic tanks are more durable than their plastic counterparts, they are susceptible to shifting or displacement if the water table rises to an excessive level. Depending on the model, these tanks may cost up to $2,000

More information may be found at: Septic Warranty Coverage and Costs.

Using Your Septic Tank

It is important to maintain the area around your new septic tank’s drain field and to frequently check your tank using the lids included with it. Never use a trash disposal in conjunction with your septic tank since it might cause the system to clog. Additionally, avoid driving over the land where your septic tank is located or putting heavy gear on top of your septic tank or drain field to prevent damage. Most of the time, after five years of septic system use, you’ll need to arrange a cleaning and pumping of the system.

Send an email to our Reviews Team [email protected] if you have any comments or questions regarding this post.

Septic System Guide: How It Works and How to Maintain It

As soon as you flush the toilet in most metropolitan locations, the waste is pumped out to the nearest sewage treatment facility. Garbage is processed at this factory, which separates it into two types of waste: water that is clean enough to be dumped into a river and solids known as residual waste. The remaining material is either disposed of in landfill or utilized as fertilizer. Septic systems, which are used in places where there aren’t any sewage treatment plants, provide a similar function, but on a much smaller scale.

What are Septic Tanks and How Do They Work?

Septic tanks are normally composed of concrete or heavyweight plastic and have a capacity of 1000 to 2000 gallons, depending on the manufacturer. In the tank, there are two chambers that are divided by a portion of a wall. The waste from the residence is channeled into the bigger room. Solids sink to the bottom of the chamber, and liquids make their way through a partial wall into the smaller second chamber, which is located above it. Anaerobic bacteria, which are found naturally in the environment, digest the solids and convert them into water, carbon dioxide, and a tiny amount of indigestible debris.

Septic Fields Distribute Liquid Effluent

The second chamber has an output pipe via which the liquid (known as effluent) from the tank is discharged to a disposal or leach field, depending on the situation. It is drained into the earth by a network of perforated pipes or through perforated plastic structures known as galleries, which are constructed of perforated plastic. It is common practice to lay the pipe or galleries in a bed of gravel, which aids in dispersing the liquid. During the course of the effluent’s percolation through the soil, the soil absorbs remaining bacteria and particles, resulting in water that is safe to drink by the time the water reaches the aquifer deeper down.

They are not much deeper than that since a large quantity of water escapes through evaporation or is transpired by grass growing above ground.

If you have sandy soils that drain too rapidly, you may not be able to treat the wastewater properly.

Sometimes the water cannot be disposed of properly because the natural soils include a high concentration of silt or clay.

Topsoil and grass are applied to the mound, which allows more water to leave through transpiration and evaporation than would otherwise be possible.

Septic Systems Rely on Gravity, Most of the Time

The majority of septic systems rely on gravity to transfer the liquid from the home to the tank and then to the field where it will be disposed of. However, due to the slope of the land, the tank or the field may need to be higher than the house in some instances. It is necessary to have a pump, or occasionally two pumps, in order for this to operate. A grinder pump, which liquefies sediments and is installed in a pit in the basement or crawlspace of the home, will be used if the tank is higher than the house.

Sewage pumps are essentially large sump pumps that are used for heavy-duty applications.

How to Treat Your Septic System

It is not necessary to do much to keep your septic system in good working order, other than cut the grass above it and keep the drainage area free of trees and plants with roots that may block it.

How Often Do You Need to Pump A Septic Tank?

You should have a septic provider pump out the particles from your tank every two years, at the absolute least. A manhole at the surface of the tank will provide the pump operator access, but older systems may necessitate digging a hole in the tank’s top so the pumping hatch can be exposed. Unless the tank is continuously pumped, sediments will build up in it and ultimately make their way into the leach field, clogging it. You’ll know it’s occurring because untreated effluent will rise to the surface of the tank and back up into the home, causing it to overflow.

Pumping the tank on a regular basis can ensure that the leach fields continue to work eternally.

What to Do if Your Septic System Fails

Solids should be pumped from the tank around every two years, according to a septic service company. A manhole at the surface of the tank will provide the pump operator access, but older systems may necessitate digging a hole in the tank’s top so the pumping hatch can be revealed. If you don’t get it pumped on a regular basis, the tank will fill with solids, which will ultimately make their way into the leach field and clog it. The untreated effluent will rise to the surface of the tank and back up into your home, which will alert you that this is taking place.

It is possible to maintain leach fields operational indefinitely by regularly pumping the tank.

• The Septic Locator provided by the National Onsite Wastewater Recycling Association
• Association of Wastewater Technicians (National Association of Wastewater Technicians)

It is rare for a homeowner to have to worry about their septic system because it is well-maintained and doesn’t cause problems. Simple maintenance, such as keeping the tank pumped and the lawn trimmed, should result in decades of trouble-free service.

What kind of protection do you have in place for your home’s systems and appliances against unforeseen maintenance needs? If this is the case, you might consider purchasing a house warranty.

• It is rare for a homeowner to have to worry about their septic system because it is well-maintained and does not cause any problems. Simple maintenance, such as keeping the tank pumped and the lawn trimmed, should provide years of trouble-free service. What level of protection do you have in place for your home’s systems and appliances against unexpected maintenance needs? If you don’t have one, you should think about getting one.

5 THINGS YOU NEED TO KNOW BEFORE INSTALLING A HOLDING TANK

Septic tank and holding tank are two words that are frequently used interchangeably. Despite the fact that they are both sanitation systems, there are significant variances between them. Both types of tanks collect wastewater from the home, but they each manage this effluent in a different manner than the other. If you want to learn more about installing a holding tank, continue reading to discover more about this type of sanitation system. 1. HOLDING TANKS ARE DIFFERENT FROM SEPTIC TANKSA septic tank is a large vessel that collects household wastewater through an inlet pipe, treats the effluent through a bio-action process, and releases the treated water into a drainfield where the water percolates underground.

1. A holding tank is also used to collect wastewater from the home, which is accessed by an inlet.
2. Secondly, STORAGE TANKS REQUIRE CONSTANT PUMPING It is recommended by experts that you pump your septic tank every two to three years, depending on factors such as the size of your family or structure.
3. If you want to utilize the holding tank on a regular basis, it is possible that you will need to clean the unit every 6 to 8 weeks.
4. The frequency with which the alarm will sound will be determined by a variety of factors, including the size of the tank and the number of people within.
5. Avoid putting unsuitable objects down the drain, such as food particles and grease, to ensure that your holding tank lasts as long as possible.
6. 3.
7. Many factors go into the construction of a functioning and fail-safe holding tank.

Additionally, you must determine the proper depth for building the subterranean tank as well as complete complex plumbing operations.

4.

Holding tank owners in California are obliged to get the necessary permits from their local Environmental Health Officer and to pay the associated costs before constructing a holding tank.

Once your holding tank has been installed, you must wait for clearance from the local health authorities before you may begin using it.

5.

In addition to permit fees, labor costs, and site conditions will all influence the cost of establishing a holding tank.

Holding tanks, on the other hand, may have a greater maintenance cost than other types of units due to the constant pumping of these units.

Overall, when comparing the upfront costs of building, running, and maintaining a septic tank to the cost of a holding tank, the holding tank comes out on top for property owners looking for the most value for their money.

It can be used in a variety of situations. Do you want to put up a holding tank at your plant to store waste? You can rely on the professionals at Pete’s Outflow Technicians to complete the work correctly. Make a phone call now to talk with one of our knowledgeable professionals.

4 Types of Septic Tanks – HomeAdvisor

The characteristics of each type of septic tank are crucial to understand whether you’re deciding which type of tank to use in conjunction with your septic system or solving a problem with your existing tank. Each installation option has its own set of pros and limitations, just like any other installation. Knowing the relative advantages and disadvantages of each option will assist you in making the right selection while establishing, repairing, or replacing your septic tank. Please keep in mind that most of these issues are the consequence of improper septic maintenance or installation.

The cost of an inspection might vary significantly based on a variety of criteria.

• Solid Waste Container— Solid waste containers made of concrete are prone to cracking and even separation. These fissures, which are usually extremely durable for several decades, might appear sooner if a poor quality concrete mix was used or if the septic system has not been adequately maintained. These gaps will allow effluence (waste) to leak out of the concrete septic tank and/or allow groundwater to seep in through the tank’s drainage system. Either scenario is undesirable. The system may get clogged as a result of a blockage. Runoff is harmful, but it will not be discovered by a typical dye test since it is invisible. If a concrete septic tank is not physically inspected, it is possible that the problem will not be discovered until it is too late and major difficulties have developed. Tanks made of steel are the least long-lasting and most unpopular of the available tank options. They are intended to survive no more than 20-25 years, although they can succumb to rust even earlier than that. Steel top covers have the potential to rust through, allowing an unwary individual to fall into the tank. It is possible to change these covers without having to replace the complete tank. If you’re purchasing a property or already live in one that has a steel septic tank cover, personally viewing the cover will not necessarily provide you a clear indicator of the general state of your tank in the long run. As with any septic tank, pay particular attention to the baffles (entry and exit points) because they are the first to corrode in most cases. Fiberglass/Plastic Septic Tank—Unlike steel and concrete septic tanks, plastic septic tanks are virtually immune to the corrosion and cracking that occurs in steel and concrete septic tanks. Nonetheless, they have their own set of difficulties that should be kept an eye out for. In some cases, a low effluent level might indicate that a blockage at the bottom of the tank has gotten dislodged. Pumping should be performed even if the effluent level seems to be normal throughout the process
• Nevertheless, any clogs should be carefully checked after the pumping. It is possible that the process of pumping a septic tank will be sufficient to remove a clog.

• In spite of the fact that plastic septic tanks are more resistant to the chemical processes that occur naturally in a septic system, their lower weight makes them more prone to structural damage. It is necessary to install the tank with care in order to avoid damage to the tank. The ground above the tank should be carefully observed. Avoid driving any vehicles over the tank’s filling station. During periods of wet soil, the lighter can also cause the tank to shift in its position in the ground. Occasionally, a plastic septic tank may emerge from the earth, destroying pipes along the way.

• Using oxygen to help in the degradation of the effluent is what aerobic septic tanks are all about, according to the manufacturer. They also necessitate the use of power. When a septic system fails, aerobic septic tanks are most frequently utilized to replace it. They can also, on occasion, minimize the amount of space necessary for their drain field. Aerobic septic tanks are generally two to three times more expensive than conventional septic tanks, but their high efficiency can result in significant savings in terms of reclaimed land in the drain field and a longer tank life. The capacity of an aerobic septic tank to function has nothing to do with its long-term dependability. A more regular and more thorough maintenance schedule is required for an aerobic septic system. Because of its more intricate breakdown structure, there is a greater possibility that something may go wrong. However, if the system is properly maintained, its effectiveness will allow you to keep your effluent under control for an almost unlimited period of time.

• Important Caution: Exercise extra caution when in the vicinity of open or uncovered sewage tanks. Falling into a sewage tank will almost always result in death due to asphyxiation. The simple act of leaning over a septic tank might lead you to pass out.

Our True Cost Report gathers information from homeowners on the expenses of small and big capacity septic systems. Use this resource while planning your installation project’s financial budget.

Plastic Septic Tanks

Plastic-Mart.com is one of the nation’s top suppliers of plastic septic tanks, offering a diverse selection of goods from the most dependable manufacturers in the business. When looking for a sewage holding tank for a residential or business installation, rotomolded plastic septic tanks made of polyethylene resins are an excellent choice. Our rotational molding technology creates better, stronger plastic tanks at a far lower cost than our competitors’ processes. We provide ribbed septic tanks for in-ground usage, as well as a large choice of other septic tank accessories.

Septic tanks are used for a variety of purposes, including holding tanks, waste storage tanks, and more.

We even offer plastic septic tanks that can be sent in as little as 48 hours, such as:

• Plastic Septic Pump Tanks: 200 Gallon Plastic Septic Pump Tank
• 300 Gallon Sphere Pump Tank
• 500 Gallon Low Profile Plastic Septic Tank
• 1000 Gallon 2 Compartment Plastic Septic Tank
• 200 Gallon Low Profile Plastic Septic Pump Tank

As one of America’s leading septic tank suppliers, we have locations spread throughout the U.S. for pick up and we offer direct drop ship straight to your door as well. Email or give us a call toll free at866-310-2556for plastic septic tank selection assistance.NORWESCO BELOW GROUND TANKS – Conversion OptionInformationSelecting an installation site for your Plastic Septic TankPlastic-Mart offers rotationally molded polyethylene septic tanks fromNorwesco, Rotonics,Ace-Roto MoldSnyder Industries. If you have any questions or would like to buy a septic tank you can do so online or call our sales department toll free at866-310-2556.

How Deep Are Septic Tanks Buried? (And How Do You Find It?)

It is possible that this content contains affiliate links. It is possible that I will receive a commission if you make a purchase after clicking on an affiliate link. In addition, as an Amazon Associate, I receive a commission from qualifying purchases.- Septic tanks, for example, might become a requirement in more remote places where some services are not readily available or easily accessible. After all, we rely on contemporary conveniences such as adequate plumbing to make our lives more comfortable and easy.

Discovering the location of your septic tank in your yard, as well as what may be grown near or on top of it, will help you determine how much of your yard is suitable for regular gardening.

You May Not Know

Despite the fact that it appears to be something that every homeowner should be aware of, understanding how deep a septic tank is buried can be difficult to determine. Perhaps you forgot about the septic tank after it was installed years ago, or perhaps you are moving into a house that already has a septic tank constructed in previously. Whatever the situation, determining the depth of your septic tank can be a challenging task under the circumstances, especially if you are unsure of the location of the lids.

The usual rule of thumb is that most septic tanks may be buried anywhere from four inches to four feet underground, depending on the circumstances.

How to Locate Your Septic Tank

Perhaps you’re unsure of the location of your septic tank on your property and are attempting to identify it on your own. There are really quite a few quick and simple methods for determining the location of your tank without having to go through a lengthy process. The first method is to follow the path laid out by your sewer lines. Typically, the tank and your drain field will be placed along a line parallel to the sewage line that goes from your property out to the street. Your home’s crawl area or basement may even have a four-inch sewage line that leads away from the structure of the building.

• Follow the pipe all the way across the yard, checking every few of feet to make sure you’re still on the right track, and then turn around.
• When you don’t feel like digging around in your yard, you can always look up your house’s address in the county records database.
• Diagrams with measurements and even the particular location of where the septic tank is located should be included in this document.
• You can also choose to dig your lid out from under it.
• This is what will tell you how many lids are on your septic tank and how many are missing.
• The majority of septic tanks are rectangular in shape and measure around in the neighborhood of 5′ x 8′ in size.
• If you are unable to determine the position of your septic tank using a probe, you will need to do a shallow excavation around the perimeter of the tank using a shovel in order to finally locate the lid.
• First, look for visual cues to help you.
• There is no doubt about it, this will tell you exactly where the tank is located beneath.
• Take a look at the plumbing in your structure, as well as the overall state of the property, to get a good sense of where the tank is situated.

It will be full to just a few inches below the underside of your tank lid when your tank is fully charged to its regular level of filling capacity. If the lid is constructed of plastic, fiberglass, or steel, the upper surface of the lid may have some variation in color or texture.

Where Should the Septic Tank Be Located?

If your property does not presently have a septic tank, but you are interested in the possibility of installing one, it is critical that you understand where it should be installed. Ordinarily speaking, most septic tanks will be situated between 10 and 25 feet away from the house. You should bear in mind that septic tanks cannot and should not be located any closer than five feet from your residence. Using a probe, you may search for flat concrete to determine whether or not a tank has previously been put on a property that you have recently purchased.

Planting Above a Septic Tank

Even though it may not appear to be the finest idea in the world, putting vegetation over a septic tank may really be perfectly acceptable as long as you choose the appropriate plants to grow. Not only is it perfectly OK to do so, but it may also be rather helpful depending on what you are planting and harvesting. It is possible to avoid erosion in your tank with the correct sort of vegetation, and it is even possible to absorb some of the additional moisture that might accumulate in your drain field.

1. Perennial plants and grasses (as previously indicated) are the ideal kind of plants to use in and around your drain field and septic tank.
2. You can use non-woody ground covers for a similar purpose as you do with woody ground covers.
3. Take, for example, the expanding environment.
4. If you don’t have access to enough sunshine, you might want to choose a shade garden plant instead.
5. Keep in mind that the soil that surrounds the septic tank drain field will typically be wetter than the surrounding soil in the rest of the yard.
6. As a result, choose a perennial such as a hollyhock, wild violet, or bee balm to ensure that you cover all of those bases when planting.
7. A septic system beneath these plants does not imply that deer will avoid the area because of its presence on your property.
8. Something like a spring bulb or an attractive grass that the deer aren’t generally interested in eating.

Plants That You Don’t Want to Grow

Just because you have the option of planting over your septic tank does not mean that everything is appropriate for this situation. A few plants should be avoided at all costs while landscaping around your septic tank, particularly huge trees that are known for their rapid growth. On the same vein, shrubs and trees with aggressive root systems are some of the worst plants to grow around your home. These roots will shoot out in quest of water, and they will not be concerned with where they locate it.

The infiltration of those roots into your septic drain field might result in catastrophic damage to your septic tank and drain field.

It’s possible that you’ll need a complete replacement.

Many other plants have strong root systems that you should avoid growing anywhere near your septic tank or drain field, and there are lots of them.

How Your Septic System Works

It is possible that understanding how your septic system operates may help you better manage, maintain, and care for it. Aside from that, it is just a large tank buried in the ground that collects your waste (which is true, but still). In remote locations, there may be a deficiency in sewage infrastructure. Because not every rural location is the same, it is not a given that septic systems will be required in your local rural area. The septic tank, in any case, serves as a form of wastewater treatment facility when there are no sewage lines available.

1. The tank is designed to be waterproof, ensuring that your wastewater does not leech into the surrounding environment.
2. Solids sink to the bottom of the container, scum rises to the top of the container, and liquids sit in the center of the three levels described above.
3. The wastewater that is being discharged from your home is the cause of the exit.
4. This liquid is carried out of your home through a pipe and into a bigger portion of your sanitary sewer system.
5. Your drain is typically comprised of a network of perforated PVC pipes that are put underground in trenches to collect water and waste.
6. Because the drains are perforated, the wastewater is allowed to seep out into the crushed gravel or stone, and then eventually into the surrounding soil.
7. The natural evaporation process will then take care of any surplus moisture in the soil, unless you do something to prevent the water from flowing out of the pipes.

How to Plan a Septic Field

It is possible that understanding how your septic system works may help you manage, maintain, and care for it more effectively. Otherwise, it is simply a large tank buried in the earth that gathers your garbage (which is true, but still). The absence of sewage infrastructure in rural regions is a common occurrence. Because not every rural location is the same, it is not a given that septic systems will be required in your local rural community. In any case, where there are no sewer systems in place, the septic tank serves as a form of wastewater treatment facility.

In order to prevent your wastewater from leaching into the ground, the tank is designed to be waterproof.

Solids sink to the bottom of the container, scum rises to the top, and liquids float in the middle of the container between the aforementioned layers of solids and liquids.

The baffle is constructed in such a way that only liquids may depart through this particular pipe and that no solids can do so.

Leach or drain fields are what you’re looking at.

In order to increase the durability and lifespan of these trenches, gravel or crushed stone are used to fill them; however, you may cover those drains with drain field cloth to prevent dirt from getting into your drains.

After a few days, the wastewater will begin to gently drift over the soil, removing the majority of the hazardous bacteria present in waste before it reaches the groundwater.

A septic service will come out to your home approximately every three years and pump the scum and sludge out of your septic tank, thereby cleaning it and resetting it back to its previous condition.