# What Does It Cost To Run Drain Pipe From Septic Tank? (TOP 5 Tips)

The average to install a sewer line ranges from \$50 to \$250 per linear foot. New pipes cost \$3 to \$20 per foot, with about \$30 to \$247 per foot for labor expenses. Trenching may or may not be included in this charge.

• The average cost is \$300, but can run up to \$500, depending on your location. The tank should be pumped out every three to five years. how does the septic tank work

## What kind of pipe do you use from house to septic tank?

Laying Out a Septic-Tank Disposal System. The septic tank should be positioned at least 50 feet from the house proper. ABS or PVC plastic or cast iron pipe can be used to connect the tank to the house drainage system.

## How deep should a septic pipe be?

A standard leach line is considered to be three (3) feet wide and three (3) feet deep with a length as required.

## How long should a septic drain field be?

A typical septic drainfield trench is 18 to 30 inches in depth, with a maximum soil cover over the disposal field of 36″; or per the USDA, 2 feet to 5 feet in depth.

## How do you calculate the slope of a drain pipe?

b) To determine the pipe slope, subtract the two manhole inverts and divide the difference by the pipe distance and multiply by one hundred (100) to obtain the percent grade of the pipe.

## What is the fall on a 4 inch sewer pipe?

For 4-inch PVC piping and a building sewer less than 50 feet long, the minimum slope is 1 inch in 8 feet, or 1/8-inch per foot, and the maximum is 1/4-inch per foot. For sewers longer than 50 feet, the slope should be 1/4-inch per foot.

## How long are septic lateral lines?

A typical drainfield trench is 18 to 30 inches in depth, with a maximum soil cover over the disposal field of 36 inches.

## How is plumbing from house connected to septic tank?

The septic tank is connected to the house by a single main drainage pipe also called inlet pipe. The water waste from your home goes through it and into the septic tank where solid and liquid waste are separated from liquid.

## What size pipe is used for septic?

A three-inch pipe is what’s used in homes to pipe toilets. The four-inch pipe is used as the building drain under floors or in crawlspaces to transport all the wastewater from a home out to the septic tank or sewer. The four-inch pipe may also be used in a home if it’s capturing two or more bathrooms.

## How far below the surface is a septic tank?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

## How do you find a buried septic tank?

Tips for locating your septic tank

1. If the septic tank lid is underground, you can use a metal detector to locate it.
2. You can use a flushable transmitter that is flushed in the toilet and then the transmitter is tracked with a receiver.

## How deep are drain fields buried?

A typical drainfield trench is 18 to 30 inches in depth, with a maximum soil cover over the disposal field of 36 inches.

## What can you put on top of a septic field?

Put plastic sheets, bark, gravel or other fill over the drainfield. Reshape or fill the ground surface over the drainfield and reserve area. However, just adding topsoil is generally OK if it isn’t more than a couple of inches. Make ponds on or near the septic system and the reserve area.

## Learn how much it costs to Install a Septic Tank.

Septic tanks range in price from \$3,157 to \$10,451, with an average cost of \$6,804 per tank. Installation of a conventional 1,000-gallon tank for a three-bedroom home might cost anywhere from \$2,100 and \$5,000. Materials range in price from \$600 to \$2,500, without labor. A comprehensive septic system, which includes a leach field (also known as a drain field), tank, and plumbing, can cost between \$10,000 and \$25,000 to install. A leach field installation might cost anywhere from \$5,000 to \$20,000, depending on the kind.

In the end, the cost of installing a septic tank is determined by the kind of system, the materials used, and the size of the tank.

This course will teach you about the several sorts of settings, such as conventional, drip irrigation, mound irrigation, evapotranspiration, recirculating sand, constructed wetland, and chambered irrigation.

## Septic System Cost Estimator

Let’s run some numbers to see what the costs are. What part of the world are you in? What part of the world are you in?

 National Average \$6,804 Typical Range \$3,157 – \$10,451 Low End – High End \$450 – \$21,000

The cost information in this report is based on real project costs provided by 948 HomeAdvisor users.

## New Septic System Cost

Most tanks and systems cost between \$2,000 and \$10,000 to install a new typical anaerobic septic system. Aerobic systems range in price from \$8,000 to \$20,000. Depending on the size of your property, the composition of the soil, and the level of the water table, you may even have to pay an extra \$10,000 or more for an alternative, specialized drain or leach field. Septic systems are composed of three major components:

• Septic tank: Either anaerobic (requiring no oxygen) or aerobic (requiring oxygen but more complicated but more efficient)
• Water runs to a leach field after it has been cleaned and separated in the septic tank, where it will naturally drain through sand, gravel, and soil in a cleaning process before reaching the water table
• Water table: Plumbing: A drainpipe to the tank, followed by another branching pipe to your field will be required.

Optional components include the following:

• Some types of systems use a dose or pump tank, which pumps wastewater up into mounded or elevated leach fields and recycles the water in some cases. Pump for aeration: If your aquarium is equipped with an aerobic system, you’ll want an aerator to force oxygen into the tank.
##### Find Local Septic Tank Installers

The installation of a traditional anaerobic system typically costs between \$3,000 and \$8,000 on average. Anaerobic systems are often less expensive to build than aerobic systems, which are more complicated. However, because they are less effective at cleaning the tank, you will need a bigger leach field to accommodate the increased burden. An anaerobic septic system is a very basic system that consists of a pipe that runs from the home to the tank and a branching pipe that runs from the tank to the drain field, among other components.

### Aerobic Septic System Cost

Aerobic systems, which are those that require oxygen to work properly, cost on average between \$10,000 and \$20,000 per system. If you’re moving from anaerobic to aerobic fermentation, you’ll almost certainly need a second tank, but the conversion will only cost you \$5,000 to \$10,000. Aerobic systems break down waste more effectively in the tank than anaerobic systems, allowing you to use a smaller drain field in many cases – which is ideal for houses with limited space. An aerobic wastewater system is a wastewater system that depends on aerobic bacteria (bacteria that thrive in the presence of oxygen) to break down trash in the tank.

You’ll need an aerator as well as an electrical circuit that connects to the system to complete the setup. Small, mounded, or speciality fields may necessitate the addition of a dose or pump tank to assist in pushing effluent (sewage or wastewater) upward or out in batches.

##### Get Quotes From Local Septic Tank Pros

Beyond the tank and leach field, there will be a few more costs to consider when creating your budget for the project. You may already have some of these costs included in your total project pricing, so make sure to get line-item prices on your estimate.

• Excavation costs \$1,200–\$4,500
• Building permits cost \$400–\$2,000
• And a perc test costs \$700–\$1,300. Labor costs range from \$1,500 to \$4,000
• The cost of septic tank material ranges between \$500 and \$2,000.
• Plastic and polymer materials cost \$500–\$2,500
• Concrete costs \$700–\$2,000
• And fiberglass costs \$1,200–\$2,000.
• 500: \$500–\$900
• 750: \$700–\$1,200
• 1,000: \$900–\$1,500
• 1,200: \$1,200–\$1,600
• 1,500: \$1,500–\$2,500
• 2,000: \$3,000–\$4,000
• 3,000: \$4,500–\$6,000
• 5,000+: \$7,500–\$14,000
• 500: \$500–\$900
• 1,200: \$1,200–\$1,

### Leach Field Cost

Installing a leach or drain field, which is a component of your septic system, can cost anywhere from \$3,000 to \$15,000 in total. The cost of a typical drain field ranges from \$2,000 to \$10,000. The drain field, also known as the leach field, is the component of the septic system that is responsible for returning wastewater to the soil. Most of the time, a flooded area in the yard or a strong stink of sewage on the property is the first symptom of a problem with the drainfield. It is possible that you may require further treatment for blocked or flooded fields, which would increase the cost of the drain field repair from \$10,000 to \$50,000.

## Alternative Septic Systems Cost

When you have a tiny property, a high water table, high bedrock, poor soil, or just wish to utilize less space, an alternate septic system is a good choice.

### Mound Septic System Cost

Installing a mound septic system can cost between \$10,000 and \$20,000 dollars. In places with high water tables, thin soil depths, or shallow bedrock, this is the most costly system to build; yet, it is frequently required. In order to create a drain field, it uses a raised mound of sand rather than digging into the soil. Its extra cost is a result of both the additional technology required to pump sewage upward into the mound and the materials and labor required to construct the mound in the first place.

### Recirculating Sand Filter Septic System Cost

Sand filter septic systems range in price from \$7,500 to \$18,500. They can be built above or below ground depending on the situation. In order to disperse the wastewater in the ground, they employ a pump chamber to force the wastewater through a sand filter. The liner of the filter box is normally made of PVC. This is accomplished by pumping the effluent through the sand and returning it to the pump tank, where it is then disseminated throughout the ground.

### Drip Septic System Cost

Drip systems range in price from \$8,000 to \$18,000, depending on the size and complexity. They operate in the same way as previous systems, with the exception that they employ extensive drip tubing and a dosage mechanism. They deliver lower dosages over a shorter period of time, which is particularly effective at shallow soil depths. This method is more expensive than a standard system since it requires a dosage tank, a pump, and electrical power to operate.

### Evapotranspiration System

Evapotranspiration systems range in price from \$10,000 to \$15,000 per system. In order to allow the liquid to evaporate from the top of an open-air tank, they employ a novel drain field configuration. They’re only usable in dry, arid areas with little rain or snow, thus they’re not recommended.

### Built Wetland System

Built-in wetland systems range in price from \$8,000 to \$15,000, with the cost increasing if an aerobic tank is included. They are designed to simulate the natural cleaning process observed in wetland ecosystems.

After traveling through a wetland tank, where it is treated by microorganisms, plants, and bacteria, it is returned to the soil. The waste also has the effect of assisting the growth of wetland plants and the population of microbes.

### Chambered System

Installation of chambered systems ranges from \$5,000 to \$12,000 dollars. They employ plastic perforated chambers surrounding pipes, which are frequently laid in sand, to keep them cool. Gravel is no longer required as a result of this. They are quick and simple to install, but they are more subject to crushing pressures, such as those caused by automobiles.

## Septic Tank Replacement Cost

The installation of chambered systems ranges from \$5,000 to \$12,000. Pipes are encircled by perforated plastic chambers that are frequently embedded in sand. Gravel is no longer required as a result of this method. The fact that they are quick and simple to install makes them more vulnerable to crushing forces, such as those caused by automobiles.

## Septic System Maintenance Costs

The installation of chambered systems ranges from \$5,000 to \$12,000 dollars. They employ plastic perforated chambers surrounding pipes, which are frequently put in sand as a protective barrier. Gravel is no longer required as a result. They are quick and simple to install, but they are more vulnerable to crushing pressures, such as those caused by cars.

### Inspect and Pump Your Septic Frequently

Installation of chambered systems ranges from \$5,000 to \$12,000 USD. They employ plastic perforated chambers surrounding pipes that are frequently laid in sand. This removes the need for gravel. They’re quick and simple to install, but they’re more vulnerable to crushing forces, such as those caused by automobiles.

• Installation of chambered systems ranges from \$5,000 to \$12,000 dollars. They employ plastic perforated chambers surrounding pipes, which are frequently laid in sand, to keep them cool. Gravel is no longer required as a result of this. They are quick and simple to install, but they are more subject to crushing pressures, such as those caused by automobiles.

### Use Household Water Efficiently

A toilet that leaks or runs continuously might waste as much as 200 gallons of water per day, although the average family consumes just 70 gallons of water. Take, for example, high-efficiency toilets, which consume 1.6 gallons or less of water every flush or less. The use of new, high-efficiency washing machines and showerheads can also help to reduce water waste, which will relieve the load on your septic system.

### Properly Dispose of Your Waste

Your septic system is responsible for disposing of everything that goes down your drains and toilets. One easy rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless it is absolutely necessary. That implies you should never flush the following items down the toilet or drop them down the sink drain:

• Your septic system is responsible for disposing of everything that goes down your drains and into your toilets. One easy rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless absolutely necessary. You should never flush the following down the toilet or pour it down the sink drain.

Everything you flush down the toilet and down the drain ends up in your septic system. One easy rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless it absolutely necessary. That implies you should never flush or drop the following items down the toilet or down the drain:

• Never park or drive your vehicle on your drainfield. Don’t ever put trees near your drainage system. Maintaining a safe distance between your drainfield and roof drains, sump pumps, and other drainage equipment
##### Get in Touch With Septic Tank Installers Near You

A septic tank or septic pump tank can range in price from \$350 to \$14,000, depending on the material used and the size of the tank. In most home situations, you won’t have to spend more than \$3,000 on the tank’s actual construction. The majority of big, high-priced units are intended for use in apartment buildings or as part of a communal sewage system.

### Concrete Septic Tank Cost

Concrete tanks range in price from \$700 to \$2,000. The total cost of installation ranges from \$2,300 to \$6,500. They’re one of the most often seen forms of installation. Despite the fact that they are vulnerable to cracking and separation, they are often resilient for several decades.

It’s critical to have it carefully inspected on a regular basis for cracks and runoff, among other things. Inspections and frequent cleanings will assist to extend its useful life. Your professional can tell you how frequently you should get it inspected, but it’s normally every one to three years.

### Plastic and Poly Septic Tank Prices

Septic tanks made of plastic range in price from \$500 to \$2,500 on average, not counting installation costs. Plastic is a long-lasting, lightweight, and reasonably priced building material. They do not break as easily as concrete and do not rust. Because of their small weight, plastics are more susceptible to harm during the installation process.

### Fiberglass Septic Tank Prices

Fiberglass septic tanks are typically priced between \$1,200 and \$2,000, not including installation. Fiberglass does not split or rust readily, but it is prone to damage during the installation process, much like plastic. However, because of its lighter weight, it is more prone to structural damage, and the tanks themselves can move in the soil.

### Steel

It’s unlikely that you’ll ever see a new steel tank constructed. They will rust or corrode with time, no matter how well-made they are at the time. As a result, they are not permitted by many municipal construction rules, and you will only encounter them in existing installations. Steel is not a long-lasting material in the earth, and it is the least preferred.

### Labor Costs to Install a Septic System

The cost of labor accounts for 50 percent to 70 percent of your overall expenses. Labor is typically more expensive than the tank itself in a normal installation, making it the most expensive option. For example, while the size required for a 3 to 4-bedroom home may cost between \$600 and \$1,100, the labor to install it might cost anywhere between \$1,500 and \$4,000.

##### Compare Quotes From Local Pros

Here is a breakdown of how much septic tanks cost in different parts of the country. Massachusetts:\$9,700 California:\$4,500 Florida:\$5,300 Texas:\$8,000 \$5,600 in New York City Colorado:\$7,800 Idaho:\$10,000

## DIY vs. Hire a Septic System Pro

The installation of a septic system is a time-consuming operation. An incorrectly fitted unit can result in water contamination, structural damage to the property, and the need for costly repairs. In addition, an unpermitted installation might make it harder to sell and insure a property when it is completed. Make a point of interviewing at least three pros before making a final decision. Contact a septic tank installation in your area now for a free quote on your job.

## FAQs

A septic tank has an average lifespan of 20 to 30 years, however it may live anywhere from 14 to 40 years, depending on the following factors:

• What it is made of is a mystery. Concrete tends to require more care, but commercial-grade fiberglass and plastic are known to survive for decades in most environments. It’s amazing how well you’ve kept it up. Every one to three years, have your system inspected and pumped out
• Every three to five years, have it pumped out. It will depend on whether or not it gets vehicle traffic over the leach field. Driving over the leach field compresses it, which increases the likelihood of it failing. The soil’s chemical makeup is important. The length of time it may endure varies depending on the soil type and depth.

### What are the signs I need a new septic tank?

There are a few indicators that it is time to replace your septic tank. These are some examples: If you smell sewage, you may have a solid waste problem in your septic tank that has to be dealt with immediately. Standing water: If there is no clear explanation for standing water, such as a significant rainstorm, it is possible that you have an oversaturated drain field, a damaged pipe, or a faulty septic system. A clogged septic tank will cause pipes to drain more slowly than they would otherwise be.

Construction on your home or the addition of more occupants will have an impact on your septic system.

pollution of nearby water: A septic tank leak can result in wastewater contamination, which can deposit nitrate, nitrite, or coliform bacteria in water sources around your property as a result of the leak.

If these bacteria are discovered in your vicinity, you should investigate your septic system to determine if it is the cause. Old age: If your septic system has reached the end of its useful life, it is time to replace it.

### Does homeowners insurance cover septic systems?

Many unforeseen and abrupt repairs to septic tanks are covered by homeowners’ insurance policies. They do not, however, often cover harm caused by a failure to perform routine maintenance. Make certain that you are pumping and cleaning it on a yearly basis.

### How much do septic system repairs cost?

Many unexpected and abrupt septic tank problems are covered by homeowner’s insurance. They do not, however, often cover damage caused by a failure to maintain the vehicle. Every year, check to see that it has been pumped and cleaned out.

• Tank Pumps cost between \$800 and \$1,500. A septic tank that is placed below the drain field may necessitate the installation of a pump to transport wastewater to the drain field. Pumping costs between \$300 and \$600 per year. Pumping is required to remove solid waste from even a perfectly functioning system every two or three years, even if it is in good working order. Tank Lids cost between \$100 and \$300 to purchase and install. If you purchase the lid and attach it yourself, it will cost you between \$50 and \$150
• Tank Lid Risers range in price from \$300 to \$1,000. Deeply submerged tanks can have their lids raised to the surface by using these devices.
##### Still Have Questions About Septic Tanks?

The average cost of sewage line installation is between \$1,300 to \$5,100. Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. Your home’s sewer connection allows you to perform things like wash your hands, take a shower, or even just flush the toilet without having to worry about clogging the system. Sewage lines link the residence to the main sewer drain and are the duty of the homeowner to install, maintain, or replace when they become damaged.

In most cases, the cost of installing a sewage line runs between \$50 and \$250 per linear foot.

## How Much Does It Cost to Install a Sewer Line Near You?

The cost of installing a sewage line varies widely depending on where you live because different cities determine their own costs based on local water resources and the present configuration of your street. For the sake of illustration, the following are some samples of what it may cost to establish a sewage line in various locations around the country:

• Massachusetts (\$2,420), Miami (\$1,760), Chicago (\$2,310), New Orleans (\$1,600), Detroit (\$3,420), New York (\$3,400), Portland (\$4,160), Houston (\$2,940), Los Angeles (\$4,130), and Dallas (\$1,630) are the top cities in the country.

## How Much Does It Cost to Install a Sewer Line Yourself?

When it comes to installing your sewage line, you should always pick a plumber with a reputable reputation. To complete this work, you’ll need specific expertise and experience, which the common homeowner just doesn’t possess. In light of the potential consequences of a faulty sewage line, which include clogged drains and pricey repairs, it is recommended to leave this home improvement endeavor to the pros.

## Sewer Line Installation Cost Breakdown

Adobe Stock PK (stock.adobe.com): The cost of sewage line installation is influenced primarily by a number of factors, including materials, labor, trenching, and permits and regulations.

## Materials

For a sewage line installation to be successful, you must first acquire the pipes that will link the main sewer drain to your property. New pipes range in price from \$3 to \$20 per linear foot, depending on the material.

## Labor

In addition, you’ll have to pay a certified plumber to install the sewage line for you. While it may be tempting to cut corners on work such as sewage line installation, it is always best to leave these tasks to the pros. The cost of labor for sewage line installation is from \$30 and \$247 every linear foot of pipe installed.

## Trenching

Installing the sewage line will also require the services of a qualified plumber.

It may be tempting to cut corners on projects like sewage line construction, but doing so will only result in higher expenditures in the long-term. Depending on the length of the sewer line, labor costs anywhere from \$30 and \$247 per linear foot of pipe.

## Permits and regulations

In addition, you’ll need to obtain permits in order to connect to the city sewer line. The cost of these licenses ranges from \$400 to \$1,600, with an average of around \$1,000. According to local rules, the cost of the project may vary, and homeowners are often needed to secure the necessary permissions well in advance of the start date. If your installation is not within the supervision of your municipality, speak with your plumber about what you need do. The ability for plumbers or contractors to get permits on your behalf may be available in specific instances.

Before beginning a sewage line installation job, you should think about any additional fees that may be involved. You should decide whether the task will necessitate tree removal, driveway repair, or patio resurfacing before proceeding. Before you agree to these additional fees, you should consult with your plumber to see if there is any way to avoid them.

## How much does sewer line replacement or repair cost?

You may require sewage line repair or replacement if anything is wrong with your sewer lines, or if you’re suffering a clog or obstruction in your sewer lines. The cost of replacing or repairing a sewage line is from \$1,400 and \$4,100, depending on the problem.

## Do I really need to replace my sewer line?

While the answer to whether or not you need to replace your sewage line may depend on your unique scenario, it’s typically a good idea to be proactive when it comes to plumbing maintenance. The unfortunate reality is that many sewage line problems simply worsen with time. When a specific problem with your sewage line, such as impinging tree roots, exists, you may be able to delay the need for a permanent solution by implementing a temporary remedy.

## How much does it cost to install a two-way cleanout for a sewer line?

For a sewage line, installing a two-way cleanout costs between \$500 to \$2,000 in labor and materials. Cleanouts that allow plumbers to reach your sewage from the outside might make it easier for them to eliminate clogs and obstructions from your sewer line.

## How to keep Septic Tank pumping costs to a minimum

There is nothing more unpleasant than dealing with the foul stench of sewage in the house, let alone dealing with dirty, stinking water on the front yard. If you’re having these problems, it’s most likely because your septic tank is full or broken, or because there is a problem with your drain field. However, there are other signs that might include slow home drains, gurgling pipes, and a very green patch of grass in the drainage field region, in addition to the typical ones such as odors and water pooling.

## Why Septic Tank pumping?

Owners are responsible for the upkeep of their septic tanks and drain fields, among other things. So you’re probably wondering how much it costs to have your septic tank pumped. It is necessary to consider a variety of criteria when determining the price for septic tank pumping. A septic tank must be pumped when the top layer of scum (or scum layer) approaches within 6 inches of the exit pipe, according to the Environmental Protection Agency (EPA). Unfortunately, you may not be aware that your septic tank is full until there is a problem, such as bad odors emanating from your drains or, even worse, a septic system backlog, which can be quite unpleasant.

See also:  What Issues With Using A Garbage Disposal With A Septic Tank? (Solution)

The septic tank receives all of the wastewater from the house, which is sent through a pipe.

Since only wastewater is disseminated into the drain field due to the tank architecture, it prevents sludge and scum from escaping the septic tank.

In addition, newer tanks make accessing the septic tank simple since they have risers that extend to ground level and are covered with lids. Septic tank entrances and subterranean access points for older tanks are provided.

## Typical problems leading to Septic Tank pumping

A septic tank is typically efficient between each pumping of the tank’s sewage disposal system. Problems, on the other hand, might arise for a variety of causes. Some of the most common septic tank issues are as follows:

• The septic tank is filled with scum and sludge that has accumulated on the surface. There are clogs or obstructions in the lines connecting the inside fixtures to the septic tank. The levels of scum and sludge in the septic tank are so high that they overflow into the drain field, clogging the drain field and preventing water from penetrating into the earth. Because of significant rainfall or a high water table, the earth has become saturated. Because of breaks in the drainpipe caused by roots or by anything else, an excessive amount of water is spilled into the field area. Because the drainpipe has been smashed, water levels in the septic tank have risen above normal, causing sewage to flow into the home’s drains.

There is little doubt that when you notice a bad stench in your house, it indicates that there is more to the situation than a full septic tank. When a professional does a septic system pumping, he or she is also trained in identifying drain field issues and sewage that is flowing in the other direction of where it should be entering the septic tank.

## What is the Septic Tank pump out going to cost?

Septic tank pump out costs are affected by several factors, the most significant of which are as follows.

• The dimensions of the septic tank
• The amount of liquid in the tank at the time of septic pumping
• Septic pumping preparation work is done by the homeowner before the service comes. In-field pipe condition
• Condition of the drain field
• The age of the septic tank (earlier tanks may not have risers)
• The type of septic tank installed. Geographical location (contractor charges vary depending on region)
• Contractor selection
• And

In comparison to the costs of repairing or replacing a septic tank or a drain field, the cost of septic tank pumping can be rather affordable in some situations. The following are the average costs associated with septic pumping:

• Septic tank pumping costs range from \$295 to \$610 on average in the United States. Costs for up to 750-gallon tanks range from \$175 to \$300
• Costs for up to 1,000-gallon tanks range from \$225 to \$400
• Costs for 1,250- to 1,500-gallon tanks range from \$275 to \$500
• And costs for 1,250- to 1,500-gallon tanks range from \$275 to \$500. Large tanks larger than 1,500 gallons cost \$600.

Most homeowners will spend between \$250 and \$500 for a septic system pumping service, depending on the size of their system. Occasionally, a homeowner might save money by prepping the space for the septic tank specialist to work in. For example, the homeowner can make certain that the tank access port is free for the technician to pass through.

## What else does a Septic pumping service do?

A regular septic tank pump out might take anywhere from one to five hours to complete. Pricing structures are determined by each individual firm. Septic tank pumping services are offered by many firms, some of which charge by the hour, while others charge a fixed rate, with additional expenses if there is more work necessary than simply septic tank pumping. Sometimes the septic pumping service will entail the repair or replacement of the septic tank. This can add up to an additional \$1,500 to the expense of septic tank pumping.

Having a drain field replaced or repaired so that the septic system functions correctly might easily cost several thousand dollars or more.

The Environmental Protection Agency (EPA) advises pumping a septic tank every three to five years in order to keep the septic system in excellent working order.

## Take the guessing out of Septic pumping cost

Don’t be concerned if this appears to be a complex process. If you keep your septic tank in good condition, it is uncommon to develop difficulties for many years. Because a well kept septic tank has a life expectancy of up to 30 years, it is important to keep it in good condition. Dealing with a septic tank mess is never a pleasant experience. Being prepared with a Plumbing Plan from HomeServe is a wise idea in this situation.

When it comes to covered repairs, we offer a selection of economical options that will help you secure your funds up to the benefit amount. Check out what HomeServe plans are available in your region by entering your zip code.

## How Much Does a Septic Tank System Cost?

A Quick Look at Septic Tank Prices

• Total cost: \$3,900 on average
• \$1,500 to \$5,000 on a sliding scale
• Anaerobic septic tanks cost between \$2,000 and \$5,000
• Aerobic septic tanks cost between \$10,000 and \$20,000
• Gravity septic tanks cost between \$1,500 and \$4,000
• Mound septic tanks cost between \$10,000 and \$20,000
• Chamber septic tanks cost between \$1,500 and \$5,000
• Conventional septic tanks cost between \$2,000 and \$5,000.

The wastewater generated by your household is teeming with potentially harmful germs. In order to properly dispose of waste and prevent it from backing up into your sinks and toilets, you must ensure that your septic tank is in good working condition. This Might Also Be of Interest to You: What Is the Difference Between a Septic System and a Sewer System? Everything you need to know about septic tank replacement, including how much it will cost, can be found in this article.

## What Is a Septic Tank?

A septic tank is an underground chamber that is used to treat residential wastewater to a modest degree. It is intended to store wastewater for an extended period of time, allowing particles to settle to the bottom and oil and grease to float to the surface. After that, the liquid waste is filtered away.

## How Much Does It Cost to Install a Septic Tank?

In most cases, a new septic tank system will cost you around \$3,900 to install. It costs between \$1,500 and \$5,000 to install a conventional 1,250-gallon tank, which is the perfect size for a three- or four-bedroom house. This price includes the tank itself, which ranges in price from \$600 to \$2,100 or more depending on the size and kind. Workman’s compensation is included in the price of the installation and often ranges from \$1,500 to \$4,000.

## Types of Septic Tank Systems

In most cases, a new septic tank system will cost you around \$3,900 to install. The cost of a conventional 1,250-gallon tank, which is an appropriate size for a three- or four-bedroom home, ranges from around \$1,500 to \$5,000. This price includes the tank itself, which ranges in price from \$600 to \$2,100 or more depending on the size and configuration. Workman’s compensation is included in the installation fee, which typically ranges from \$1,500 to \$4,000.

### Anaerobic Septic System

Anaerobic systems are a popular alternative for many homes since they don’t require any additional electricity or chemicals to function properly. Anaerobic systems include microorganisms that do not require oxygen to exist and hence are called anaerobic systems. Solid waste is broken down by microbes, and any leftover liquid waste is pumped out and spread beneath the surface of the soil. The garbage is naturally recycled when the water seeps into the ground and returns to the environment. The installation of these devices is between \$2,000 and \$5,000.

### Aerobic Septic System

Aerobic systems, in contrast to anaerobic systems, make use of microorganisms that do not require oxygen to live. To activate the bacteria in the tank, oxygen is injected into it, and the bacteria then feed on the solid waste. Aerobic systems perform effectively in soils that are unsuitable for other systems and in areas where the groundwater table is elevated. It is an excellent choice for residences that are close to a body of water. Aerobic systems are more costly to install than anaerobic ones.

### Gravity Septic System

Gravity septic systems employ gravity to filter and move water through the system.

They must be put on a mild slope in order to allow water to flow without the use of a pump. The cost of installation ranges from \$1,500 to \$4,000.

### Conventional Septic System

A standard septic system is comprised of a septic tank and a trench that serves as a drain field for the collection of waste. The trench is built on stone or gravel and is designed to allow water to move through it easily. In order to prevent sand or dirt from contaminating the clean soil, geofabric is laid over the top of the trench and secured in place. In order to function properly, a traditional septic system requires a huge amount of room. The installation of these devices is between \$2,000 and \$5,000.

### Mound Septic System

If your groundwater table is close to the surface, a mound septic system is the most appropriate option for your situation. An area for the septic system is prepared, and a sand mound is built to allow effluent from the tank to be pumped into the mound in modest amounts. The sand then acts as a filter, preventing the water from reaching the soil and groundwater. This design necessitates a large amount of floor space. They’re also expensive to install since a sand mound needs to be built before they can be utilized.

### Chamber Septic System

Chamber septic systems have lately gained popularity as an alternative to traditional septic systems. They are comparable to conventional systems, with the exception that plastic chambers, rather than gravel, are utilized in the drain field. These are less difficult to build and have a lower carbon footprint. The cost of installing them ranges from \$1,500 to \$5,000.

## Septic Tank Materials

Another aspect that influences cost is the type of material used to construct your septic tank. The following are some of the most often seen materials:

### Concrete

Concrete septic tanks are the most prevalent form of septic tank because they are extremely long-lasting and reliable. They can survive for 20 to 30 years if they are properly maintained. Concrete, on the other hand, may break with time. When concrete is reinforced with rebar, the strength of the concrete is increased when subjected to pressure. Because of its weight, installation is more difficult and necessitates the use of specialized equipment. The cost of a typical-sized concrete tank ranges from \$720 to \$2,050 dollars.

### Fiberglass

Concrete septic tanks are the most frequent form of septic tank since they are the most long-lasting variety available. They have a lifespan of 20 to 30 years if they are properly maintained. Concrete, on the other hand, is susceptible to cracking with age. When concrete is reinforced with rebar, the strength of the concrete is increased. Its weight necessitates the employment of more sophisticated installation techniques and equipment. It costs between \$720 to \$2,050 to build an average-sized concrete tank.

### Plastic

Tanks made of plastic are lightweight and simple to install. They’re also fairly long-lasting. Plastic tanks range in price from \$830 to \$1,400 on average, depending on the kind.

### Steel

In spite of steel’s strength and durability, septic tanks built of steel are susceptible to rust and collapse if not properly maintained.

As a result, several municipal governments have tightened their restrictions in order to discourage their usage. Typically, you’ll discover them in regions where the system was already in operation. If you are able to have one installed, they range in price from \$900 to \$9,900.

## What Size Septic Tank Do You Need?

The size of your septic tank is normally decided by the number of bedrooms in your house. This is used to calculate the amount of water that will flow through the system on a daily basis. In general, the expense of a system increases in direct proportion to its size.

### Two Bedrooms

A septic system with a minimum of a 750-gallon septic tank is required for a two-bedroom residence. However, in many localities, a 1,000-gallon tank is the least capacity that may be accommodated.

### Three Bedrooms

A minimum of a 1,000-gallon water tank is required for a three-bedroom residence, which handles around 360 gallons of water each day on a daily basis.

### Four Bedrooms

A bigger tank, with a minimum volume of 1,250 gallons, is required for a four-bedroom residence. It is capable of handling around 480 to 600 gallons of water each day. Additional Related Articles:

• How to keep the cost of septic tank pumping to a bare minimum
• 3 Symptoms of Sewer and Septic System Problems
• Do you have a clogged sewer line? Here’s What You Should Do
• Water Sewer Line Repair: Do It Yourself or Hire a Professional
• Listed here are 15 common plumbing problems that every homeowner should be aware of.

## Septic Tank Repair Costs

It’s conceivable that only a certain component of your septic tank has to be replaced rather than the complete tank. Repairs and replacement parts can be purchased for a fraction of the cost of a complete system replacement. The following are some of the most often seen repairs:

### Drain Field

Drain fields can get overloaded and flood, resulting in sewage backing up into toilets and sinks. The cost of replacing a drain or leach field ranges from \$3,500 to \$11,000.

### Tank Pump

A replacement septic tank pump typically costs between \$500 and \$1,200.

### Tank Filter

It is the most typical type of filter change that is performed by homeowners. It typically costs between \$230 and \$280.

### Tank Lid

Concrete coverings and steel lids may break and corrode as a result of exposure to the elements. In most cases, you can repair a septic tank lid on your own for about \$35 and \$60. In most cases, having it changed by a professional is more expensive.

### Tank Baffle

The baffle is responsible for directing wastewater through the septic tank. A replacement baffle piece will cost between \$23 and \$44 dollars.

A septic tank can be built either below or above ground, depending on your preferences. Because of the amount of excavating and footing preparation required, installing a tank underground is a pricey endeavor. Underground septic tanks necessitate the construction of a drain field that can accommodate a soakaway. In addition, because the soakaway allows for part of the wastewater to drain into the ground, the tank will require less emptying over time. Over time, this might result in a reduction in your expenditure.

Some demand that an inspector check and approve the site, which might result in a fee being charged to the homeowner.

## How Long Does a Septic Tank Last?

The lifespan of a septic tank varies based on the material used and the type of system used. The lifespan of a septic tank might be reduced if the tank becomes clogged due to roots or floods from groundwater. Septic systems have a lifespan of 15 to 20 years on average. Maintaining your septic tank on a regular basis is the most effective approach to extend its life. Keep in mind that maintaining your tank entails more than just draining out the contents; it’s also crucial to have a professional evaluate your tank on a regular basis and perform routine maintenance.

In the event that you have a plan in place, you can call our 24-hour repair hotline anytime a covered problem develops. We’ll dispatch one of our locally based, licensed, and highly qualified professionals to complete the work for you right away.

## How Much Does a Septic System Cost?

 Medium: Averages \$2,000-\$5,000; Runs \$4,000-\$12,000 in Higher Cost Areas Enhanced System: \$10,000-\$20,000+
For homes that aren’t connected to a municipal sewer plant, a septic is an on-site system that collects, treats and disposes of household wastewater by slowly filtering it through underground soil. Typically there are two main parts, a septic tank and a soil absorption system (also called a drainfield, leachfield or disposal field). These are located underground and connected to the house by sewage pipes.Typical costs:
• The cost of installing or rebuilding a traditional septic system (including the tank) is from \$2,000 to \$5,000 in the Midwest, but can range from \$4,000 to \$12,000 or more in locations with higher material and labor costs. Septic systems that are designed, engineered-like or alternative septic systems, such as mounds, soil/peat filters, aerobic systems, and/or artificial wetlands, can cost \$10,000 to \$20,000 or more, according to the Rhode Island Regional Water Quality Program. These alternative septic systems perform better than the conventional technique in areas with high groundwater levels or soil that is slowly or fast percolating, as well as in areas near drinking water supplies, wetlands, coastal ponds, or other water resources. Simply installing a septic tank will cost between \$500 and \$1,800 based on its size (varying from 300 to 1,000 gallons) and kind. It costs an additional \$100-\$200 to purchase piping and other necessary supplies
• New Mexico State University gives an overview of the septic tank installation process. Many locations, however, require that a septic system be planned and constructed by experienced and licensed experts

Related articles:Septic Tank Cleaning,Sewer Line Replacement,Replacing Copper Pipes What should be included:

• It is necessary to employ Septic systems when sewage treatment plants are not accessible, which is typically the case in rural or suburban areas with big lots. Essentially, a septic tank is a huge, underground, waterproof container that can be constructed of concrete, fiberglass, or plastic (polyethylene). An explanation of how septic systems function and where they might be utilized can be found at the North Carolina State University Ag Extension
• Installing or replacing a septic system might take anything from a few days to a week or more. The procedure entails substantial excavating, which is frequently accomplished using powerful earth-moving equipment.
• The majority of counties and states require a construction permit for the installation or replacement of a septic system, which may cost anywhere from \$250 to \$1,000 or more depending on the location and complexity of the job. For further information, contact your local building and planning department. A septic system installation typically entails substantial digging and damage to the landscaping
• New grass and other plantings can cost anywhere from \$100 to \$1,000 or more.
• Unlike individual septic tanks, each house has its own underground septic tank, but all of the septic tanks are connected to a single drainfield, leachfield, or soil absorption system. A cluster septic system, which is often implemented by developers, distributes the expense of drainfield installation and maintenance across a large number of dwellings.
• To find out if your local sanitation agency maintains a list of licensed septic installation firms, contact them and ask. Onsite wastewater recycling contractors can be found by contacting the National Onsite Wastewater Recycling Association for recommendations. Inquire about training and previous experience. Check to see if the firm is legally bonded, insured, and licensed in your jurisdiction.
CostHelper News What People Are Paying – Recent Comments Page 2 of 2-Previous12
 Posted by:Fredbill in Ashland, VA. Posted:October 28th, 2020 10:10AM Type:PVC pipe

When flushing my toilet during wet weather, it was gurggling and not flowing out properly. Septic company wants to replace old black pipe with PVC pipe running 80 feet from septic tank to distribution box. They think the 65 year-old black pipe is collapsing. Is \$37.50 per foot a reasonable price?

 Posted by:Fiorella in Miami, FL. Posted:July 28th, 2020 05:07PM Type:Conventional septic

Septic tank needed repair. House did not have a drain fill. Had one collapsed leg that was installed years back. Repair was done to the tank and an entire drain fill with 5 legs was installed. My house is located in a high water table. I hired a reputable plumbing company that offers a three years warranty. Is this a reasonable price to pay for repairing a septic tank and installing a complete drain fill with 5 legs?

 Posted by:Dorie Dew in Nederland, CO. Posted:May 22nd, 2020 02:05PM Type:leach field install

I am being told that because of county planning dept regs and not enuf “soil” (4 ft) before bedrock here in the Rockies, it will cost \$40,000 to install a septic system for a 2 bedroom home (the smallest unit). Please tell me there is an alternative!

 Posted by:in Stone Mountain/atlanta, GA. Posted:September 9th, 2019 04:09PM Type:New system

1000 gallon septic tank with 195 feet of quick 4 plus high capacity infiltrator per county code. Inlet line from house to tank plumbing with level 3 soil test and permit. By Easy Clean Septic 678-532-1276 Easycleanseptic.com

 Posted by:in Stone Mountain/atlanta, GA. Posted:September 9th, 2019 04:09PM Type:New system

1000 gallon septic tank with 195 feet of quick 4 plus high capacity infiltrator per county code. Inlet line from house to tank plumbing with level 3 soil test and permit.

 Posted by:Gregory Chappel in Trinidad, CA. Posted:August 15th, 2019 01:08PM Type:New tank and drain field

1500 gallon tank, 4″line, 90′ rock trenches took 3 days

 Posted by:Unclebob in McArthur, CA. Posted:January 26th, 2019 09:01AM Type:Trailer park

I fought septic tank, leach field problems for years. this is a trailer park, with 35 trailers going into a 7500 gallon tank with 1000 feet in length of leach field. The killer was cooking oil and grease. Plugged up the leach field. Educating the tenants made a huge difference. Then I found the magical cheap combination that worked much better than those expensive enzymes.Equal parts, Yeast, Brown Sugar, and Baking soda.

I mix a pound of each and flush it down a toilet every couple of months. My Pumpings have gone from every 6 months to every 3 years, and it is not as bad at 3 years as it used to be at 6 months. Sams club and Costco sell it in bulk cheap.

 Posted by:a user in moreland, GA. Posted:July 20th, 2018 12:07AM

That seems like a lot of money for s single drain line

 Posted by:Sfr Development LLC in Boone, NC. Posted:August 11th, 2017 12:08PM Type:Conventional 2 Foot Chambers

1000 gallon tank. In Mountains Boone NC. Have 30 inches to 48 inches of soil. 3 – 60 Feet 2 foot chamber lines

 Posted by:rrrr in berlin, NJ. Posted:July 12th, 2017 02:07PM Type:septic

location-south jersey-sandy soil approx cost please? looking for economy and conformity.

 Posted by:Any Help Appreciated in Charleston, SC. Posted:May 12th, 2017 08:05AM

Getting ready to purchase a piece of land that requires a septic system in order to build. From soup to nuts, (permits, materials, installation) what should I be looking at for total cost? This house will be built very close to water(Charleston, SC less than.5 miles) How long does the process typically take? Any and all help truly appreciated

 Posted by:Ken Carbaugh in Leesburg, VA. Posted:June 20th, 2016 06:06PM Type:conventional to alternative systems

A perc or perk test in Northern Va from a licensed consultant will cost between 1200-2500 dollars depending the district and county fees. Fairfax County costs are 2-4x as much due to local health dept bureaucracy and redtape requiring a surveyor and engineer to be used for any certification or permitting. Real costs of conventional systems (3-4 bedrooms) are from 14-25k depending on the soil percolation results and whether or not a pump is required. If the system is an alternative (BAT in MD) the design costs add 1000-2500 in costs and the installation of the specialized equipment adds costs that can total 20-35,000 easily.

Your property is the most valuable asset you will own so be careful with the land you contract to purchase and beware not all property is equal in value for development.

 Posted by:Bob42 in High rolls, NM. Posted:March 25th, 2016 12:03PM Type:Concrete tank, leachfield

\$5500 was the total cost for everything including permits and inspection certificate, tank, pipes, new leachfield etc. I live rurally in a mountainous region with sloping land so more work was required to remediate the land for the leach field to be level. Took about a week from contract signing to completion.

 Posted by:Susana in cumming, GA. Posted:August 24th, 2015 04:08PM Type:treating the leach field

I had a septic company come to do a septic tank pump for \$150 but they said I needed a more expensive leach field treatment at a cost of over \$2500 even thought there is no back up or smell anywhere. They wind up doing an enxyme one leaving me with 6 gallons of liquid enzyme I am suppose to pour down the toiled once a month. My son says I was ripped off. Is he right?

 Posted by:payed too much? in Effort, PA. Posted:August 2nd, 2015 11:08PM Type:dual tank w mound

Had Pump replaced as well as wire to house, dug up yard, to replace line, replaced pump, didn’t take garbage, didn’t clean up landscape, pump both tanks included in price, found truck parts in driveway and tanks not pumped, claim truck broke be back to pump.was this a lot, I had to rake out landscape and driveway, clean wires, boxes and garbage left behind,.I hope they pump the tanks soon.

 Posted by:Daytrp in Eldersburg, MD. Posted:July 17th, 2015 08:07PM Type:Repair – new construction

Repair permit: \$130-450 depending on county.New construction permits: \$250-550.New septic \$16-22k for advanced treatment, \$8-10k conventional Perc test for repair: \$850-\$1,400 takes 2-6 hours. Done with county sanatarian onsite. A common septic repair: (installation of 2 – 60′ long x 3′ wide x 8′ deep with 4′ of stone below pipe invert) runs about \$6,500.Trench dimensions are determined by number of bedrooms (occupancy) and percolation rates from perc test. price varies depending on Trench size.

Some states Have programs to help upgrade your septic tank. Check with your county health department.I bid these jobs and this is my basic start point. Specailty jobs, difficulty of access, heavy rock, all add to the bid price

 Posted by:ABMCCAA in Bakersfield, CA. Posted:June 26th, 2015 05:06PM

New 1500 Gallon Tank, Engineering, 60′ of Leach Field with Rock base drainage system. 50 ton of 3/4″ rock, new 4″ main line to house, soils testing and permits. Took 3 days total.

 Posted by:andrewbasil in hemet, CA. Posted:March 23rd, 2015 06:03AM Type:simple leach line replacement

75 feet of leach line were dug up and replaced the. attached up to original fifteen hundred gallon 1973 concrete septic tank and re buried. they had to knock down two fruit trees and by accident sheared off a water tap. (Having not repaired the water line it has now become a 5 foot stream shooting straight up in air.) I do feel grandmother was taken advantage and charged double of not more for services that. and this is the worst part. a permit nor independent inspection was never done for this job.

Help me out here what do I do?

 Posted by:ltodd kinsey in cda, ID. Posted:February 26th, 2015 11:02PM Type:all

If properly maintained a working system should never need pumped

 Posted by:M. IRIARTE in STROUDSBUR, PA. Posted:February 4th, 2015 05:02AM Type:SEPTIC

ANYONE IN THE POCONOS HAS HAD THEIR SEPTIC SYSTEM REPLACE. WHAT WAS THE COST OF REPLACEMENT.WOULD LIKE TO GET FEEDBACK Page 2 of 2-Previous12 External Resources:

1. Twri.tamu.edu/reports/1999/l5234.pdf
2. sohioline.osu.edu/aex-fact/0744.html
3. s

More Articles on the Subject of the Home and Garden

 Check Out All Costs for Home and Garden How Much Does a Kitchen Remodeling Cost? How Much Does a Propane Tank Cost? How Much Does a Plumber Cost?
 CostHelper is based in Silicon Valley and provides consumers with unbiased price information about thousands of goods and services. Our writers are experienced journalists who adhere to our stricteditorial ethics policy.