- THE TANK LEVEL ALARM prevents overfilling of liquids by sounding an alarm when liquid level changes the position of the float switch. Very easy to install – just screw the tank-mount into the tank fitting. Battery powered units need no wiring, no electricians.
How do you adjust a float switch?
Adjusting a manual float switch is easy. Start by moving the rod or tether up or down based on the water level in the pit. Most systems can be adjusted by hand or with a normal sized screw driver. Shorter tethers and rods work best for lower water levels while higher tethers and rods are better for higher water levels.
How does septic alarm float work?
A float switch inside the tank tells the pump when to come on, and a separate float switch operates an alarm that comes on when the water level exceeds a preset minimum. Aerobic septic systems also need alarms, even if the ground doesn’t slope.
How do you adjust pump floats?
How to Adjust a Tethered Float Switch Level on a Sump Pump
- Step 1: Turn Off Your Pump’s Power Source.
- Step 2: Adjust the Float Cord.
- Step 3: Pour Water Into the Sump Pump.
- Step 4: Adjust the Float Rod.
- Step 5: Pour Water Into the Sump Pump.
Can I turn off septic tank alarm?
If the alarm happens to be going off, the best thing to do is to push the red button or switch on the alarm box. This will turn off the alarm. There should be a red light and a green light located somewhere on the alarm box. The green light means that the alarm has power and should always be on.
Why is my septic tank beeping?
When the septic alarm sounds, it tells you that there is a problem getting wastewater to the drain field. Several different things may cause this. Most septic tanks have an alert when there’s too much water inside of it and could cause some kind of backup or overflow if not dealt with promptly.
How high should the float be on a sump pump?
The Float Switch should hang a few inches above the top of your sump pump motor. The exact height will vary depending on the size of your sump pit and the power of your sump pump motor.
How does a float switch work on a submersible pump?
The float switch works by simply turning the pump on when the water level goes up and turning it off when the level goes down. Because of this, the float switch is the most common failure, or most vulnerable component of a submersible pump.
How do you open a float switch?
Normally closed float switch: The electrical circuit is closed in the down position and open in the up position. So, with gravity pulling it down it is closed and as the liquid level rises to the pre-set level it will open.
Where is the float switch on a septic system?
For switches and alarms that can be installed into new septic tanks, a side-mounted float switch might be a better option. These switches are run through the side of the tank, rising and falling with water levels to an open or closes position.
Why does my septic alarm go off when it rains?
Heavy Rain – Heavy rain causes groundwater seepage into your septic system. When it overflows, your alarm may go off. Parts Problem – Your alarm will likely go off if one of your septic system’s components is faulty. It could be your pump, floats, your timer – or the alarm itself.
Why is my float switch not working?
When it comes to the failure of this type of float switch, it generally comes down to certain common causes. These causes include the incorrect configuration of the switch, poor maintenance, using a float switch that is not designed for the purpose or using a float switch that is not properly rated for the application.
Can a sump pump be too powerful?
You don’t want a pump that is either too small or too powerful. If the pump is too small, it won’t be able to keep up with water flowing into the basin. If the pump is too powerful, it will “short cycle.” This means the pump will start and stop frequently, which can cause premature pump failure.
How to Troubleshoot Septic Float Switches
Septic tank alarms and float switches are included with your septic system if it employs a pump to transport wastewater from the tank and onto a drain field. Septic tank alarms and float switches are optional. When the float reaches an unacceptably high level, an alarm is activated to alert you that your tank may be on the verge of overflowing. It is possible for the float switch to fail and cause the alarm to ring even when the tank is not overflowing. Attempt solving the problem yourself first before calling a service expert for assistance.
Step 1
If the float’s alarm is sounding, turn off the alarm switch on the float. An overflow in the system or a defective float are both indicated by this condition.
Step 2
Anything plumbing-related in your home that discharges water into the septic system, such as the washing machine and dishwasher, must be turned off immediately.
Step 3
Reset the alarm by pressing the button on the wall. Wait between six and eight hours before turning on your water supply. If the alarm does not ring again after this length of time, it is likely that the problem is anything other than a sewage overflow.
Step 4
The float switch should not be turned off by checking the circuit breaker or the GFCI plug (Ground Fault Circuit Interrupter) for a trip. If moisture is allowed to enter the outlet, the GFCI plug will trip. When the circuit is tripped, a light will illuminate to show that it has happened. Attempt to reset the GFCI plug by pressing the button on the plug, or turn off and on the circuit breaker to reset the circuit breaker. If the circuit breaker or GFCI outlet trips again, this indicates that there is a problem with the wiring or that there is moisture in the circuit.
Step 5
Check to see if the pump is activated by pressing the on/off switch on the float switch. A dead switch or a defective pump might be to blame if this doesn’t work for you.
Step 6
Verify that the on/off switch on the float switch activates the pump by pressing it on and off many times. A dead switch or a defective pump are the most likely causes of this problem.
How to Wire a Septic Pump Alarm
Home-Diy Septic system alarms notify the homeowner if there is a possibility of a sewage backup. Internally, a float switch that is anchored to a fixed point in the tank floats up and down in response to the level of the liquid in the tank. When the liquid level rises over a certain threshold, a switch inside the float shuts the alarm circuit, resulting in the alarm being activated. When the length of the sources is equal to zero, this.parentNode.removeChild(sources); otherwise, this.onerror = null; this.src = fallback; )(, arguments.target.currentSrc.replace(), ‘, /public/images/logo-fallback.png’) ” loading=”lazy”> ” loading=”lazy”> Septic alarms notify homeowners when there is a problem with their septic system.
While one wire is dedicated to powering the pump, the other is dedicated to the septic pump alarm circuit.
Installation of the alarm float switch is done by septic system contractors on the inside of the septic tank. The connection of the float switch to the alarm circuit is still the responsibility of the homeowner in this case.
- Electrical conduit
- Septic alarm float
- Screwdriver
- Septic alarm with mounting hardware
- Junction box with cover Two wire nuts for wire with a gauge of 12 AWG
Tip
By gently pushing on the wire connections, you can determine whether they are secure. Physically raising the alarm floats to their upright position will allow you to test the alert. The alarm will ring if everything is done correctly.
Warning
A junction box must not be connected to the septic tank via a direct conduit. Gases from the septic tank might seep into the connection box and pose an explosive threat to the surrounding area.
At the Tank
- Locate the float wires for the alarm system as well as the alarm circuit wires that lead to the home. (They should be clearly labeled.) Push the wires through the electrical conduit and into the junction box as quickly as possible. To assemble the black wires, hold the bare ends of each together and place the pair into a wire nut, twisting it until it is secure. Carry out the same procedure with the white wire and the other wire coming from the float switch
- Install the junction box lid and tighten it down to hold in all of the electrical wire.
In The Home
- In a high-traffic area near the incoming septic tank alarm wires as well as an electrical plug-in, install the alarm. Incorporate the mounting screws into the alarm housing by threading them through the mounting holes. Screw the alarm into the wall. Connect the black wire coming from the septic tank alarm circuit to the positive terminal of the alarm system. Connect the white wire to the negative terminal on the circuit breaker. Screw the terminal lugs all the way down until they are tight. The alarm’s power connector should be inserted into the power receptacle.
The Drip Cap
- Septic system alarms notify the homeowner that a sewage backup is impending
- Nevertheless, they are not always effective. Float switches are located inside the septic tank and are connected to a fixed point in the tank. (Float switches should be clearly labeled to indicate where they are located.) The alarm’s power connector should be inserted into the power receptacle.
How a Septic Tank Alarm Works
A septic alarm provides you with early warning of potentially serious problems. iStock/Getty Images image courtesy of Katarzyna Bialasiewicz/iStock An effluent pump is required in any typical septic system in which the drain field is located at a higher elevation than the tank in order to move wastewater from the tank to the drain field. The pump is controlled by a float switch located inside the tank, and an additional float switch runs an alarm that sounds when the water level in the tank drops below a certain minimum.
The Need for a Septic Alarm
Septic systems that are gravity-fed transport waste from the house to a holding tank where solids settle to the bottom and overflows leave through an outlet onto the drain field. Whenever a pump is required to convey waste to a higher elevation – as is frequently the case – the pump is activated by a float, similar to the one found in a toilet tank. Pump or float failure can cause major difficulties, such as a sewage backlog in the home or an overflow of the tank’s holding tank. If the system generates an alarm, the problem may be identified and remedied as soon as possible, avoiding the worst repercussions.
Alarm Operation
The septic alarm is activated by a separate float switch, which should be connected to a separate electrical circuit in order for it to continue to work even if the breaker controlling the pump is thrown. When the water level reaches the preset cut-in point for the float switch, a buzzer, a light, or some other alarm mechanism may be activated, which may be positioned on the tank, on the side of the house, in the basement, or in a utility room, depending on the configuration of the switch. Alarms connected to a municipal grid are required in some areas so that authorities may monitor sewage systems that are not operating properly.
What the Alarm Means
When a septic alarm goes off, it typically signifies that the water level in the tank has risen too high, which indicates that the pump is not working properly. It’s possible that the circuit breaker that controls it has tripped, and all you have to do is reset it to correct the situation. Another possibility is that the pump is blocked and has to be repaired, or that a continuous leak is forcing it to work too hard as a result of its overwork. The worst-case situation is that the drain field becomes clogged, and the pump is unable to rid the tank of waste materials.
Because this may occur during a period of heavy rain, the drain field is saturated; you should turn off the pump and avoid from using the plumbing until it has dried up completely.
Aerobic Septic Systems
In an aerobic septic system, compressed air is pumped through sewage in order to encourage decomposition. This sort of system also requires an alert to function properly. It is regulated by a switch that is sensitive to air pressure, and when it trips, it typically indicates that the compressor pump is not working properly. It is common for this sort of system to contain a separate storage tank for treated water as well as a pump that directs the water to pop-up sprinklers that distribute it over the drain field.
Troubleshooting a Sticking Float in a Septic Tank
Pump chambers in septic tanks feature effluent pumps that are actuated by float switches. Float switches are used in septic systems to activate alarms and to shut down and restart effluent pumps. It is possible for float switches that have been put incorrectly or carelessly to become stuck on other wires in the tank or become useless owing to debris in the tank. Sticking float switches fail to warn a homeowner that sewage is backing up into the house. 3ups or failing to switch off an effluent pump are unacceptable.
Septic tank floats should be examined for good operation on a regular basis, and this should be done every time septic tank maintenance is conducted.
Step 1
Effluent pumps are housed in the pump chambers of septic tanks, which are controlled by float switches. To activate alarms and to halt and restart effluent pumps in septic systems, float switches are used. Because of the dirt in the tank, float switches that have been poorly or carelessly fitted may become stuck on other wires in the tank or ineffective altogether. In the case of stuck float switches, homeowners are not alerted to sewage backup. Failure to switch off an effluent pump is a 3ups offense.
Septic tank floats should be examined for good operation on a regular basis, and this should be done every time septic tank maintenance is carried out on the system.
Step 2
Look for electrical cables and other trash in the tank and note where they are. The wires connecting from the float switches to the pump’s standpipe should be firmly secured and should not obstruct the free movement of the floats in any manner.
Step 3
Reduce the height of the pump hook until it is below the float switch’s position. Raising and lowering the float switch will allow you to determine whether an electrical wire or other debris is preventing it from moving.
Step 4
Ensure that the float is in its completely open position before bumping it. If the pump does not pump or the alarm does not sound, the float has to be bumped again. If the alarm is triggered or the pump is activated, the float should be replaced.
Step 5
Replace the access cover for the septic tank’s upkeep.
Warning
When working around sewage tanks, you should use caution. Don’t forget to put on your safety gear.
What do I do if My Septic Alarm is Going Off?
In the event that your septic alarm goes off, it may surely create some anxiety and uncertainty; and if you happen to be experiencing this right now, then you’ve arrived to the correct location! Don’t be concerned; it does not necessitate urgent action. Instead, take your time to go through this full essay so that you will be prepared to act now or in the future if the situation arises. What Septic Systems Are and How They Work The alarm works in conjunction with the septic system to alert you when the water level within the pump tank has increased to an unsafe level or has decreased to an unsafe level.
- The timer is in charge of regulating the time intervals during which the pump is permitted to pump wastewater into the drainage system.
- Thus, during periods of excessive water use, the drain field is kept from getting overflowing, which might cause damage to the drainage system.
- A large amount of water is injected into the system in between pumping cycles for whatever cause, and the water has nowhere else to go but back into the system’s pump tank.
- Depending on how much water was and continues to be put into the system and how the pump is set up to operate on a timer, it may take many pumping cycles until the water levels are returned to normal.
- There is an excessive amount of water being put into the septic system. This is the result of excessive water use, which might be caused by multiple loads of laundry, an excessive quantity of dishwashing, or a disproportionate number of long showers.
- Somehow, groundwater is making its way into the system. If there is an excessive amount of standing water surrounding the septic tanks, whether generated by rain or another source, the water may seep into the tanks and cause the internal water level to rise.
- It’s possible that one of the components of the septic system is malfunctioning. If anything goes wrong with your system — including the pump and floats — the alarm and timer will go off and the septic system will stop working correctly.
The Best Thing to Do If Your Alarm Goes Off Alternatively, if you hear an alert, you should press the red button or turn on the alarm box. The alarm will be turned off as a result of this action. There should be a red light and a green light on the alarm box, which should be situated someplace on the unit. The green light indicates that the alarm is operational and should be left on at all times. It is shown by a red light if the alarm is getting a signal from the pump tank indicating that the water level is increasing above or decreasing below what is expected.
- If the breaker occurs to be tripped, look around the septic tanks to see if there is any standing water.
- It is possible that the red light on the alarm box will go out on its own after allowing the septic system to operate for a couple of pump cycles (which should take approximately 10-15 hours).
- If the red light turns off, it signifies that the system is operating properly and that it only needs to catch up with the extra water that has overflowed into the storage tank.
- To be clear, an alarm signal from the septic system does not always imply that sewage is about to back up into the house right away.
- Do you require septic system repair on a regular basis or emergency service?
To arrange an appointment, please call (804) 581-0001 or send us an email through our contact page. Want to learn more about septic systems? Explore our septic system web sites by clicking on the “Septic” navigation option in the top navigation bar.
How to Check Your Septic Panel and Pump Chamber
It is recommended that you inspect your pump chamber once a year to ensure that everything is in proper working order. Follow the 11-step procedure outlined below to complete this task on your own! (Do you require further assistance? Alternatively, you may watch our instructional video below.)
1. Let’s start by inspecting the panel. Make sure the power is on by verifying the power switch to the panel is on.
The following items should be included in this general overview: The electrical box may be seen in the lower left corner of the image below, starting at the bottom of the image. Check to verify that all of the cables are firmly connected before using it. Next, take a look at the lower right corner of the shot, where you can see the discharge pipe for the pump. Check to see if it is operational (valve should be lined up with pipe). It’s now time to have some fun!
FIRST.PUT ON GLOVES!That is one step you DO NOT want to miss. Remove the float tree (the pipe with a pvc handle located upright left in our picture) and pull up the alarms.
*Please keep in mind that these instructions are for a 4-float system. Some systems contain only two or three floats.
If you don’t hear an alarm, this is cause for concern. Starting at the top, I will explain the floats and how to ensure each one is working.
NOTE: If your water supply is depleted, you may need to replenish it. Fill it up a little with water from a yard hose.
7. Continue testing.
Check that the pump is operating properly by flipping the second float from the bottom upside down and then turning it back around. With your other hand, turn the next float up (which would be the second from the top) upside down while still holding the first float. You should be able to hear the pump start up. As soon as you have confirmed that the pump is operational, just release these two floats. There’s one more float to go. The top float serves as an alert in case of high water. Turn it over down to see whether this is the case.
8. Now is the time to inspect the power cords.
Check to see that everything is securely tied to the float tree and not just hanging free. Zip ties can be used to reattach any stray cables.
9. Securely return the float tree to its holder and coil any dangling cords so that they are out of the water.
In the United States, approximately one-quarter of homes rely on a specialized septic system to handle their household wastewater. A septic system is a fragile system that is dependent on a number of biological and mechanical processes to function properly. Septic systems that are properly maintained are rarely in need of repair, but even the finest upkeep cannot avoid every problem. Because of this, an operational septic tank alarm system is an extremely critical component of any system. Septic tank alarms alert you when water levels in your tank rise to the point where backup or overflow is possible.
How does a septic system work?
Septic tanks are subterranean tanks that are normally found in the back or side yard of a residence. An intake pipe allows water from the residence – such as laundry waste, shower water, dishwater, and toilet waste – to enter the tank. Heavy solid waste sinks to the bottom of the tank (referred to as the “sludge layer”), while lighter waste, such as oil, floats to the top (referred to as the “scum layer”) of the tank. Clarified water is left in the centre of the container. The clean water is then discharged through a discharge pipe into a drain field that has been designated.
It is generally recommended that septic tanks be emptied of collected solid waste once every three to five years in order to avoid jams and backups.
Environment factors such as a drain field that is too saturated with water to absorb septic output, excessive water consumption, or clogs created by inorganic materials such as cigarette butts or sanitary napkins can also cause backup.
What happens when a septic system backs up?
In the vicinity of the residence, septic tanks are often buried underground in the back or side yard. An input line allows water from the residence to enter the tank, including laundry waste, shower water, dishwater, and toilet waste. Heavy solid waste sinks to the bottom of the tank (this is referred to as the “sludge layer”), while lighter waste, such as oil, floats to the top (this is referred to as the “scum layer.” It is left in the center to act as clarification. The clean water is subsequently discharged through a discharge pipe onto a drain field that has been set aside for this purpose.
It is generally recommended that septic tanks be cleaned out of collected solid waste every three to five years in order to avoid obstructions and backups.
This Is Where A Septic Tank Level Sensor Is Needed
Backups can be avoided by using a high-quality septic tank sensor in conjunction with regular maintenance and waste treatment. A floatswitch is programmed to sound an alarm when the water level in the tank becomes dangerously high, alerting you to the situation and allowing you to take steps to reduce water use and identify the source of the problem before it is too late. Even while most septic tank sensor alarm systems have the float switch set at a level where you will still have a day or two of regular water consumption before an overflow or backup is near, it’s still critical to conduct an investigation as soon as possible after receiving an alarm.
Choose SMD Fluid Controls for Your Float Switch
The septic tank level sensor may fail if the float switch is not trustworthy, resulting in a septic tank backup and the need for a replacement. If you’re installing or updating your home’s septic tank alarm system, make sure to use the best switch you can find in order to guarantee long-term performance and reliability. There is a large choice of float switches and other liquid level sensors available from SMD Fluid Controls that are ideal for use in septic tank alarm systems, including sump-style floats and horizontal switches as well as bespoke multilevel sensors and other options.
Get in touch today!
For the collection, treatment, and distribution of sewage and wastewater, many Ramsey MN residences rely on their own on-site septic system. Certain sewer systems are fitted with a Septic Tank Alarm, which serves as a warning device in the event that the pump is not operating properly. Depending on the severity of the problem, it might be as simple as aTripped Breaker or as significant as aMechanical Problem or a Clogged Outflow Line. If you are unable to reset the breaker panel, contact a Licensed Septic Repair Company such as CSI Custom Septic, Inc.
Why Is My Septic Tank Alarm Going Off?
Homeowners are intended to be informed when there is a problem with the Septic Pump through the use of a Float Alarm System. The alarm is most likely programmed to sound when the water level in the tank climbs to within a few inches of the tank’s maximum capacity.
Because no one likes to see sewage backing up into their home’s plumbing system, it is critical to respond swiftly if your alarm is sounding. Reasons for your septic tank alarm to beep or red light to remain on include:
- Septic Pump Electrical Problem
- Septic Tank Pump Mechanical Problem
- Septic Alarm Malfunction
- Clogged Outflow Line Failed on/off float switch
- Faulty pump timer
- Excessive water consumption in the home
- Excessive rain or flood water entering the septic tank
Steps To Take When Septic Alarm Goes Off
It is important not to be alarmed if you hear an alert from the Septic Pump Tank.
- To silence the alarm, use the Silence Button. Look for a Green Light, which shows that the alarm has been activated. A flashing red light indicates that there is a problem with the Pump or one of its parts. Look for a tripped circuit breaker or a ground fault interrupter. If necessary, reset the control panel. Discontinue the use of the water for up to 8 hours to check whether the pump is able to empty away the surplus water and switch off on its own. In order to have your septic system inspected and repaired if necessary, contact CSI Custom Septic, Inc.
Licensed MN Septic Repair Company
The Quality Septic Services that CSI Custom Septic, Inc. provides to keep your home’s sewage system healthy and in optimal functioning condition are provided by a Licensed Septic Repair Company CSI Custom Septic, Inc. You shouldn’t hesitate to contact us if you hear yourSeptic Alarm going off and need assistance in repairing the situation. Our crew is experienced in repairing problems with septic pumps, switches, and alarms, as well as other septic components. Maintaining and inspecting your sewer system on a regular basis will help you avoid unneeded sewer problems on your home.
provides quality septic system inspections and repairs in the Ramsey, Minnesota region.
undefined
Some residences are equipped with septic systems rather than relying on the city’s public sewer system. It is your responsibility to maintain and clean your septic tank, which includes maintaining it in excellent functioning order and pumping it on a regular basis. If you own your septic tank, you are responsible for all of the cleaning and maintenance that goes along with it. In this case, a septic tank alarm system might be of great assistance to you. Unless you have an entirely new septic system put on your property, there’s a good probability that you already have a septic tank alarm placed someplace in your residence.
- An overview of the many types of septic tank alarms Essentially, a septic tank alarm system is a gadget that monitors water elevation inside the tank and sends you notifications when the water level is much higher or lower than it should be.
- It is recommended that all septic systems that include pumps be equipped with a timer that regulates when the pump can push waste water into the drain field.
- Timer systems operate the pump for specific periods of time at specific times of the day.
- When the controls cycle back and on again, the water level within the pump tank rises as a result.
- The causes of rising water levels are as follows: There might be a variety of factors contributing to low tank water levels.
- Repeatedly doing laundry, running the dishwasher continually, and having everyone in your home take a lot of long showers are all examples of practices that contribute to excessive water use.
- Seepage may occur if there is an excessive amount of rain.
- Alternatively, it is possible that anything is wrong with a septic component (pump, timer, alarm, floats).
- Whenever your septic tank alarm is triggered, just press the red button or switch on the emergency alarm box to silence it.
- Check to see that the septic system is operating properly and that there is no standing water around the tank before proceeding.
During this period, you should reduce your water consumption. Mike’s SepticMcKinley Sewer Services will answer any concerns you have concerning a specific septic alert in Prior Lake, Minnesota. We’re here to assist you!
PumpAlarm.com Sewage and Septic Alarm Kit
Everything you need to monitor a high water level (or a low water level if necessary), as well as high and low temperatures and power failures is included. Helping to avoid damage caused by pump failures or septic system overflows, as well as receiving warnings when systems fail due to a power outage, is possible. This product is intended for indoor usage only. If you are placing it outside, it must be protected from the elements with a weatherproof enclosure.
What’s Included:
1 – Cellular Detection Unit One Tether Switch for Septic and Sewage Applications, four AA Batteries, and instructions. 4 – Straps for mounting Hose Clamps (no. 2) 3 – Plastic Anchors and Screws for Mounting 1 – Installation Guide for a Quick Start One-Year Limited Warranty Among the several sensor possibilities are: Sensor de l’eau numérique This product is ideal for drip pans, floor drains, and beneath appliances. Float Switch with Digital Display A single float that is ideal for pit, tank, and crock installations.
Sump pump applications benefit from multi-level water monitoring, which is provided by this device.
What Are the Annual Costs of this device?
There is now a one-time cost of $49.99 for a yearly subscription. This refers to the device’s capacity to send and receive text messages in real time. You can cancel your subscription to the service at any time. Once you have unsubscribed, your unit will lose the ability to send text messages as well as the ability to adjust the temperature sensor and other input customizations. However, your unit will continue to sound the audible alarm for any inputs or temperature thresholds that you have previously set, as well as chirp when the batteries are running low.
How does our alarm help protect Your property?
Would you choose to remedy an issue before it happens if you were given the opportunity? The built-in temperature sensor allows you to check the temperature of the indoor air from any location where you have cellular connectivity. Text messages are sent out in the case of a power loss, a low temperature, a hot temperature, as well as for further sump pump monitoring and basement flood protection. Alerts that you want to be aware of at all times, 24 hours a day, seven days a week.
Where should you use a Cellular Sump Pump Alarm?
Due to the tilt switch included in the package, you’ll receive early notice of grinder pit and septic system overflows, allowing you to prevent damage and costly cleaning as a result of blackwater leaking into living spaces. Along with excellent water detection, the supplementary water detector ($15, available here) allows you to monitor areas around drains, water pans, and beneath appliances such as refrigerators, water heaters, and air conditioning units in addition to the primary water detector.
Why is PumpAlarm.com your best choice?
We have faith in this technology to the extent that we have engineered and manufactured it, and we stand by it completely. Receive real-time notifications before harm happens, and be assured that we will provide complete assistance for the device’s installation and operation.
We’re happy only when you’re satisfied. Find out why so many people rely on PumpAlarm.com as the sole option for protecting their homes from costly damage.
What do I do when my septic alarm goes off?
Posted on 04/37/2009 at 04:37 0 Comments on hinBlog When the water level in the pump tank rises beyond what is considered normal or falls below what is considered normal, an alarm system will sound. It is recommended that all septic systems with pumps be equipped with some type of timer. The timer regulates the amount of time that the pump is permitted to pump waste water into the drain field. During periods of increasing water consumption, this protects the drain field from becoming overloaded with water.
- Systems that use timers allow the pump to run for a predetermined period of time at particular times of the day.
- The water level within the pump tank will rise until the pump is able to be turned back on.
- This is something that can happen from A-C.
- An excessive amount of water is being pumped through the septic system.
- It appears that groundwater is entering the system.
- If there is an excessive amount of standing water surrounding the septic tanks, the water may seep into the tanks, causing the water level within the tanks to rise.
- It’s possible that one of the components of the septic system is malfunctioning.
When the alarm goes off, pressing the red button or turning on the alarm box is the recommended course of action.
Both a red and green light will be put on the alarm box for easy identification.
The presence of a green light indicates that the alarm is operational.
After that, check the septic breaker to ensure that the septic system is receiving electricity.
If the breaker is off, turn it back on.
During this period, try to use as little water as possible to save money.
Simply put, it needed to catch up with the excess water that had been pumped into the system.
An alarm signal does not necessarily indicate that sewage is ready to overflow into the residence.
If the warning is sounding, restrict your water use to the bare minimum.
If something goes wrong, the slowed water flow will give you plenty of time to fix it before sewage backs up into the home and floods the house.
Call Us Right Now! Vac-Tec SepticWater LLC.11603 Canyon RD. EPuyallup, WA 98373PH:(253) 268-0322WS:vactecseptic.com Vac-Tec SepticWater LLC.11603 Canyon RD. EPuyallup, WA 98373 Links: Call us at (253) 268-0322 or stop by our location at to talk with an expert about your system.
Sump Pump High Water Alarms, Float Switch, Septic Tank Control Panels, Pump Floats
You may place an order online or call our sales department at 1-877-925-5132 for help.
Observer 500 SerieS Outdoor High Water Alarm15′ or 30′ mechanical alarm float, 6′ Power Cord
It is used to monitor liquid levels in sump and sewage basins, septic tanks and aeration systems, cisterns, and other similar applications. Easy installation is made possible by the inclusion of a 6-foot power wire and outlet. Specifications of the product
- With a big light and a loud trumpet, this indoor/outdoor alarm will keep you safe. Mechanical alarm float with tie strap in 15′ or 30′ lengths
- Electrical Connectors that are watertight
- Power cord with plug for easy installation
- 6 foot power cord with plug for easy installation Horn mute and alarm test switch are included. Primary voltage is 120 volts, secondary voltage is 12 volts, and the frequency is 60 hertz. 6.5 watts maximum in alarm status
Availability: IN STOCKWith 15′ Mechanical Switch Item10A500 Click To View Larger Image EASY INSTALLATIONBox Dimensions: 5.5′ x 3.75′ x 3.75’Observer 500 Specifications Observer 500 Installation Manual
All high water alarms are shipped out the same day, free of charge.
VersAlarm™ I/OOutdoor High Water Alarm15′ or 30′ Mechanical alarm Float, 6′ Power Cord
Water level monitoring is accomplished with the VersAlarm I/O series High Water Alarm, which is utilized in sump and sewage basins, septic tanks and aeration systems, cisterns, and a variety of other applications. Easy installation is made possible by the inclusion of a 6-foot power wire and outlet. Enclosure that has been UL listed. Specifications of the product
- With a big light and a loud trumpet, this indoor/outdoor alarm will keep you safe. Mechanical alarm float with pipe mount for 15′ or 30′ lengths of pipe. Power cord with plug for simple installation
- 6′ power cord with plug
- Electrical cable connections that are watertight are supplied. It is possible to drill and install to satisfy specific requirements
- There is no electrical plug included with this alarm. 120 VAC, 5 amps maximum, 60 Hz
- Nema 4X waterproof thermoplastic enclosure that is UL approved
- THREE-YEAR WARRANTY WITHOUT DEALEXTENDING
Availability: IN STOCKWith 15′ Mechanical Switch Item8040 Click To View Larger Image ITEM QUALIFIES FOR WHALE OF A DEAL.CLICK HERETO SEE WHAT IT MEANS! Box Dimensions: 5.0′ x 5.3′ x 2.25’VersAlarm I/O Specifications
You may place an order online or call our sales department at 1-877-925-5132 for help.
Observer 400 Series Outdoor High Water Alarm15′ Mechanical alarm Float, No Power Cord
It is used to monitor liquid levels in sump and sewage basins, septic tanks and aeration systems, cisterns, and other similar applications. Enclosure that has been UL listed. Specifications of the product
- With a big light and a loud trumpet, this indoor/outdoor alarm will keep you safe. With a 15-foot mechanical alarm float and a tie strap
- Auxiliary Dry Contacts at 120VAC
- The electrical box connections are not included. It is possible to drill and install to satisfy specific requirements
- There is no electrical plug included with this alarm. It has to be wired. 120 VAC, 5 amps maximum, 60 Hz
- Nema 3R waterproof thermoplastic enclosure that is UL approved
Availability: IN STOCKItem10A400 Click To View Larger Image Box Dimensions: 6.5′ x 4.5′ x 3’Observer 400 Specifications Observer 400 Installation Manual
You may place an order online or call our sales department at 1-877-925-5132 for help.
VersAlarm™ I/OOutdoor High Water Alarm20′ Mechanical alarm Float, No Power Cord
Water level monitoring is accomplished with the VersAlarm I/O series High Water Alarm, which is utilized in sump and sewage basins, septic tanks and aeration systems, cisterns, and a variety of other applications. Enclosure that has been UL listed. Specifications of the product
- With a big light and a loud trumpet, this indoor/outdoor alarm will keep you safe. Mechanical alarm float with pipe mount, 20′ in length
- The electrical box connections are not included. It is possible to drill and install to satisfy specific requirements
- There is no electrical plug included with this alarm. It has to be wired. 120 VAC, 5 amps maximum, 60 Hz
- Nema 4X waterproof thermoplastic enclosure that is UL approved
Availability: IN STOCKItem7032 Click To View Larger Image Box Dimensions: 5.0′ x 5.3′ x 2.25’VersAlarm I/O Specifications
All high water alarms from septic solutions® are sent quickly and at no additional charge.
BIO-HWAP SINGLE Light Control PanelHIGH WATER ALARM WITH multiple circuits
This control panel, which has many circuits, is used to detect rising water levels. You can use several circuits to operate a submersible pump that is not connected to the high water alert circuit at the same time. Specifications of the product
- Pumpalarm circuits are protected by circuit breakers
- An external run/test/mute switch is required. Audible alarms that are externally mounted
- A 360-degree red alarm light
- An external loud buzzer with a high decibel volume
- The enclosure is a Nema 4X. Listing of UL 508A panels
- Internal wiring that is color coded
- Floats are available for purchase separately.
Availability: IN STOCKItem50B010 Click To View Larger ImageBox Dimensions: 10.25′ x 8.5′ x 4’Floats Sold Separately! Click Here! Outside View of the Control BoxNeed Help? Watch This Video! Features and Specifications
Do you require assistance in selecting a high water alarm? Please contact us at 1-877-925-5132 toll free.
Observer 100 SeriesPedestal Alarm Outdoor High Water Alarm With float switch
In addition to monitoring liquid levels in sump and sewage basins, as well as septic tanks and aeration systems, cisterns, and other storage containers, the Observer 100 Series Pedestal High Water Alarm is also employed in other applications.
The pedestal may either be fitted over a 4×4 post or it can be inserted straight into the ground to complete the installation. Specifications of the product
- In addition to monitoring liquid levels in sump and sewage basins, as well as septic tanks and aeration systems, cisterns, and other storage areas, the Observer 100 Series Pedestal High Water Alarm is also employed in other applications. Installing the pedestal into the ground is as simple as sliding it over an 8-by-4-inch post or digging a hole in the ground. Details about the product
Item10A100 Click To View Larger Image Dimensions: 6′ W x 35′ H x 6′ DEASILY INSTALLS ON 4×4 POST or directly into the groundObserver 100 Specifications Observer 100 Installation Manual
We have the greatest collection of septic goods on the internet, with over 1000 different options!
Power Post 4x Pedestal AlarmOutdoor High Water Alarm With float
The Power Post 4X pedestal alarm and pump connection center is intended for use with a septic tank or pump tank to monitor levels in the tank. The Power Post 4X is equipped with a high-water alert as well as a power connection for a submersible pump, among other features. Specifications of the product
- Pedestal with a 48-inch height and an alarm for excessive water
- Mechanical Alarm Float Switch with Pipe Mount
- Female Plug for Submersible Pump Connection
- Alarm Test and Mute Switch
- 20ft Mechanical Alarm Float Switch with Pipe Mount
- A red polycarbonate beacon with an audible buzzer (100 dB at 10 feet)
- A NEMA 4X watertight enclosure that is UL 508 approved
- 120VAC, 60Hz
- And a three-year warranty are included.
Availability: IN STOCKItem7115 Click To View Larger Image Box Dimensions: 48′ x 5′ x 5’Features andSpecifications
Pedestal with a 48-inch height and an alarm for high water. Mechanical Alarm Float Switch with Pipe Mount; Female Plug for Submersible Pump Connection; Alarm Test and Mute Switch; 20-foot mechanical alarm float switch with pipe mount; A red polycarbonate beacon with an audible buzzer (100 dB at 10 feet); a NEMA 4X watertight enclosure that is UL 508 approved; 120VAC, 60Hz; and a three-year manufacturer’s warranty
Observer 200 SeriesIndoor High Water Alarm 15′ Mechanical Float, 6’Power Cord
It is used to monitor liquid levels in sump and sewage basins, septic tanks and aeration systems, cisterns, and other similar applications. Easy installation is made possible by the inclusion of a 6-foot power wire and outlet. This product is strictly for indoor usage! Specifications of the product
- With an audible and visible trumpet, this indoor alarm box may be set off at any time. Float with mechanical alarm 15′ in length
- A 9V battery backup
- A power wire with a connector that is 6 feet long. Dry contacts for auxiliary purposes
- Terminal connectors that snap together in a flash
Availability: IN STOCKItem10A200 Click To View Larger Image EASY INSTALLATIONBox Dimensions: 6′ x 3.75’x 2.5′ Observer 200 Specifications Observer 200 Installation Manual
To speak with a member of our customer care team, please call us toll free at 1-877-925-5132.
Versalarm™Indoor High Water Alarm 15′ Mechanical Float, 6’Power Cord
Using the VersAlarm series High Water Alarm, you can keep track of liquid levels in sump and sewage basins, septic tanks and aeration systems, cisterns, and a variety of other applications. Easy installation is made possible by the inclusion of a 6-foot power wire and outlet. This product is strictly for indoor usage! Specifications of the product
- With an audible and visible trumpet, this indoor alarm box may be set off at any time. Float with mechanical alarm 15′ in length
- A 9V battery backup
- A power wire with a connector that is 6 feet long. Dry contacts for auxiliary purposes
- Warranty for three years
Availability: IN STOCKItem7001 Click To View Larger Image Box Dimensions: 6.0′ x 4.0’x 2.0′ VersAlarm™ Specifications
Septic Solutions provides fast and free same-day shipping on all high water alarm products.
Versalarm™ SUMP PITIndoor High Water Alarm WITH WATERSPOTTER™ PROBE FOR USE IN SUMPS
In sump and sewage basins, the VersAlarm series High Water Alarm is used to monitor the amount of liquid in the basin. When the water level on the Waterspotter Probe reaches the sensors on the probe, the buzzer and light on the probe will be triggered. When compared to a float switch, the Waterspotter Probe takes far less area to function. Specifications of the product
- With an audible and visible trumpet, this indoor alarm box may be set off at any time. WaterSpotterTM Probe is mounted to a pipe and has a 15-foot cord with a 9-volt battery backup. a power wire with a plug measuring 6 feet in length
- Dry contacts for auxiliary purposes
- Warranty for three years
Availability: IN STOCKItem7002 Click To View Larger Image Box Dimensions: 6.0′ x 4.0’x 2.0′ VersAlarm™ Specifications WaterSpotter™ Probe Diagram
To speak with a member of our customer care team, please call us toll free at 1-877-925-5132.
Versalarm™ FLOOD SENSORIndoor High Water Alarm WITH WATERSPOTTER™ FLOOD SENSOR
The VersAlarm series High Water Alarm is intended to warn people of impending flooding before it occurs. When the water level on the Waterspotter FloodSensor reaches the sensors on the device, the buzzer and light on the device will be triggered. This device is used to detect floodwater around sump pits, washing machines, and water heaters, among other things. Specifications of the product
- With an audible and visible trumpet, this indoor alarm box may be set off at any time. WaterSpotterTM Sensor with a 15-foot cord, a 9-volt battery backup, and a 6-foot power wire with a plug. Dry contacts for auxiliary purposes
- Warranty for three years
Availability: IN STOCKItem7003 Click To View Larger Image Box Dimensions: 6.0′ x 4.0’x 2.0′ VersAlarm™ Specifications
Put your trust in the professionals with more than 20 years of expertise in the wastewater business.
