How to choose the best location for a septic tank?
- Apply for Permits Check Before You Dig You should never start any type of digging before checking your local septic system regulations.
- Consider the Terrain A septic tank should be installed on high,even ground that’s free of any dense root systems. Avoiding slopes and steep declines will prevent flooding.
- Test the Soil
Are septic tank locations public record?
Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.
How do you find a septic tank in an old house?
Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.
How do you find a metal detector with a septic tank?
6 Steps to Locate a Septic Tank
- Find Your Main Sewer Drain Line. Sewage from your toilets, sinks, and showers collects into a main drain line.
- Check Permits and Public Records.
- Determine Septic Tank Material.
- Time to Dig.
- Mark the Location for Future Maintenance.
How do I find out if my septic tank is registered?
Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.
How were old septic tanks built?
Many of the first septic tanks were concrete tanks that were formed out of wood and poured in place in the ground and covered with a concrete lid or often some type of lumber. In the 1960s, precast concrete tanks became more prevalent as the standard of practice improved.
How long do septic tanks last?
A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.
How deep is a septic tank in the ground?
Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.
How often should a septic tank be pumped?
Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.
Can you use a metal detector to find sewer lines?
Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.
Are septic tanks metal?
Steel Septic Tank—Steel septic tanks are the least durable and least popular tank option. Designed to last no more than 20-25 years, they can be susceptible to rust even before that. Steel top covers can rust through and cause an unsuspecting person to fall into the tank.
Are septic tanks made of metal?
The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.
How To Find My Septic Tank
- What is a septic tank
- How do I know if I have a septic tank
- And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
- What to Do Once You’ve Discovered Your Septic Tank
You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.
“How can I locate my septic tank?” is one of the most often requested inquiries we receive.
When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.
How to Locate Your Septic Tank
Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.
What Is a Septic Tank?
Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.
Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.
How Do I Know If I Have a Septic Tank?
What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.
- A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
- A septic system is likely to be installed in your home if you reside in a rather rural location.
- Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
- When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
- Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.
Why It’s Important to Know the Location of Your Septic Tank
What is the best way to determine whether or not your home has a septic system? The majority of the time, there are a few indicators. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage network. It is probable that the utility company will not charge you for wastewater or sewage services if you are utilizing a septic system to handle your wastewater management. Of course, if you have a septic system, there is a chance that you will not get a water bill at all!
- There is a good chance that you are utilizing well water rather than public utility water if the water pipe leading into your home does not have a meter attached to it.
- You are more likely to have a septic system in your home if you reside in a more rural setting.
- The likelihood is that your home is also equipped with a septic system if all of your neighbors are.
- It is common to find a mound or tiny hill on the property where a septic tank is installed that is not a natural structure.
Checking your property records is a foolproof method of determining whether or not your home has a septic system. It is quite probable that the construction permit and plans for your home and land will include information concerning the existence (or absence) of a septic tank on the site.
1. To Be Able to Care for It Properly
The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.
2. If You Want to Landscape or Remodel Your Property
Identifying your septic tank is important for several reasons. For starters, knowing where your tank is helps you to provide correct maintenance and care for it. Building or putting heavy things on top of a septic tank is generally not recommended, as it might cause damage. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it as well. Due to the weight of the automobiles, there is a risk that the tank would collapse due to excessive pressure.
3. If a Problem With Your Tank Occurs
Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.
4. Ease of Getting It Fixed
Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away
1. Use a Septic Tank Map
First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.
- If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
- The county health department is responsible for keeping track of septic systems.
- A septic tank’s position could be depicted on a survey map, for example.
- The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.
In this way, if you ever decide to sell your property, you will be able to supply the new owner with everything they will need to locate the tank and properly manage their septic system.
2. Follow the Pipes to Find Your Septic Tank
Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.
- In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
- By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
- The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
- Going via the sewage line itself is another method of locating the septic tank utilizing it.
- Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
- When the snake comes to a complete halt, it has almost certainly reached the tank.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.
3. Inspect Your Yard
Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation.
However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:
- Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
- Directly in front of the home Immediately adjacent to your well (if you have one)
- In close proximity to trees or densely planted regions
- In the shadow of a patio, deck, or other building
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.
Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.
4. Talk to Your Neighbors
If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.
5. Look for Your Septic Tank Lid
It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.
The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.
What to Do After You Find Your Septic Tank
Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.
However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.
1. Mark Its Location
The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.
2. Take Care of Your Septic Tank
Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.
In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.
For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.
Call a Professional Plumber
Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.
Request an Estimate for the Job
How Do I Find My Septic Tank
What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00
How Do I Find My Septic Tank
Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.
A tiny proportion of septic tanks have a capacity of 3000L or more.
Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.
If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system. To learn more about our wastewater treatment plant, please visit our Waste Water Treatment Plant website.
How Can I Find My Septic Tank?
Is There a Septic Tank on My Property? It is extremely possible that you have a septic tank or a waste water treatment system if your home is situated on an acreage or in a rural location. In what shape and size does the septic tank come in? Typical 1600L concrete septic tanks account for the great majority of installations. A spherical concrete top with a large lid in the center and two smaller lids on either side is used to hold the items. Although the lids of these tanks may have been altered or modified on occasion, this is not always the case with these tanks.
Three-thousand-liter (3,000-liter) capacity septic tanks are available.
We have a 3000L septic tank, and our expert is opening the hefty lid.
A waste water treatment plant system may be present if you have discovered a tank or tanks that do not look like the ones shown in these photographs.
- There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.
The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.
Check the rest of the toilets in the home by repeating the procedure.
Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.
a link to the page’s load
How to Locate Your Septic Tank
It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.
This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.
How To Find A Septic Tank: Step By Step
It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.
1. Gather Some Helpful Tools
Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.
Using this method, you may also locate the cover for your septic tank.
While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.
2. Use a Septic Tank Map
If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.
3. Start Ruling Areas Out
The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:
- Immediately adjacent to your well
- Beneath your home
- Directly against your home
- For example, underneath your driveway
- Under trees
- And other locations. Structures like a patio or deck are good examples of this.
4. Inspect Your Property
If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.
When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.
The likelihood of your septic tank being discovered in a few specific locations is quite high. Because of code issues or just because it doesn’t make sense, it’s highly unlikely that your septic tank will be located near any of the following locations:
- Your water well, if you have one (for a variety of reasons that are rather clear)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
- Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping
5. Inspect Your Yard
A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:
- If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
- Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.
The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.
6. Follow Your Sewer Main/Sewer Pipes
Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.
The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.
If the line is labeled, it is usually made of plastic or rubber.
7. Check Your Property Records
Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.
If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.
What to Do Once You Find Your Septic Tank
Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities.
You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!
How to Find Your Septic Tank
Many folks have contacted me through e-mail (typically from across the nation) to inquire about the location of their septic tank. “I have no idea,” I generally say as a helpful response to the question. I really want to add something like, “It’s just off your driveway, near that bushy thing,” or anything along those lines. But, truly, even for the most experienced searchers, septic tanks are difficult to come by. The following are some strategies you might employ to assist you in locating your tank.
- Precaution should be exercised before you get started.
- So, proceed with caution!
- Please let me know if you have any queries or need assistance.
- Get to know the beast!
- tanks are normally buried 4 inches to 4 feet below the surface of the ground.
- You might be astonished to hear that someone knows exactly where it is hidden in plain sight.
- It is against the law to dig or probe in your own yard without first locating and marking the underground services.
You will receive the following tools to aid you in your search: Measurement tape, tile probe, and a shovel (if you are ambitious) The following tools are required: a metal detector (borrow or rent one since septic tanks often include iron steel rebar in the lids), and a hoagie sandwich (because locating sewage tanks makes you hungry.trust me on this).
- Examine the basement wall to see where all of the pipes join together and exit through the basement ceiling.
- If you don’t have a basement, walk outdoors and check for the roof vents on your house.
- Ordinarily, the sewage line that leads to the septic tank will exit the home right below this ventilation opening.
- On sometimes, the ancient proverb “The grass is always greener on the other side of the septic tank” is true.
Your tank may be located by probing or digging for it, and with luck, you will locate it. Keep in mind that not everything that seems to be a septic tank actually is! It’s possible that you came upon one of the following instead:
- Rubble buried in the ground (not to be confused with Barney Ruble)
- SepticDrywell
- An old foundation
- In case you happen to live in a cemetery (which is spooky), you may use a grave vault to keep your belongings safe.
After a few hours of unsuccessfully digging around in your yard, it will be time to eat your hoagie and take a short nap. Following that, it will be necessary to rent or borrow a metal detector. In the event that your next-door neighbor collects Star Wars action figures or has more than three unidentifiable antennas on his roof, there is a good chance that you can borrow his metal detector. If you’re lucky, the metal detector will actually assist you in finding your septic tank, rather than just a bunch of old buried automobile parts.
- According to local legend, a pumper known as “Zarzar The Incredible” can locate septic tanks with a metal measuring tape measuring 30 feet in length.
- Continue to push your commode (“commode” sounds sophisticated) tape farther and farther down the pipes until he “feels” the bottom of the tank with his tape.
- I recently purchased locate equipment that can be used to locate septic tanks, and I’m excited about it.
- For more information, please contact me at 574-533-1470.
- After that, you can have a video of the inside of your sewer pipes created!
- Related: Visit our Septic System Maintenance page for more information.
- Services provided by Meade Septic Design Inc.
- Both Clients and Projects are included.
- Send me an email!
How to Locate a Septic Tank
A surprising number of homeowners have had to figure out how to find the location of a septic tank on their premises. If you’re purchasing a home with a septic system or discover that your property’s tank hasn’t been maintained in years, you’ll want to know where the tank is located because all septic tanks must be pumped at some point in time. In the course of a real estate transaction, the property owners or real estate agent may be aware of the location of the tank. Inquire about the “as-built,” which is a schematic of the septic system and the specifics of its installation.
Unfortunately, locating the septic tank may not be as simple as it appears.
In other cases, not filing the as-built with the local health department was not required. Because septic system permits have only been needed in Oregon since 1972, you may have to depend on visual indicators to determine whether your system is working properly.
1.Follow the Outgoing Sewer Pipe
Look for the four-inch sewage pipe that runs through the structure and the location where it exits the building in the basement or crawl space. Locate the location outside the building where the pipe exits the building or the location of an access cover over the pipe. It is required that septic tanks be at least five feet away from the structure, although they are usually between 10 and 25 feet away. You may follow the pipe all the way to the tank using a metal probe. It is important to note that sewage lines may curve and run around the corner of a building rather than following a straight path to the holding tank.
2.Search for Septic Tank Risers and Lids
Depending on their age, septic tanks are either one- or two-compartment structures. Each compartment has a cover, with two additional lids for dual-compartment tanks that were added later. If the tank includes an access point known as a riser, the lid may be readily visible from outside. Look for round, plastic discs that are about a foot or two in diameter. Due to the fact that the lids might be flush with the ground or just a few inches above it, they can get overrun with grass and other plants over time.
Tanks without risers are likewise equipped with lids, however they are located underground.
3.Find the Drain Field First
Depending on their age, septic tanks can be divided into one or two compartments. For dual-compartment tanks that were installed later, each compartment has two lids. For tanks with an access point called a riser, the lid may be readily visible from the outside. Try to find a foot- or two-wide round plastic disc. Due to the fact that the lids can be level with the ground or just a few inches above it, they can get overrun with grass and other plant life. Additionally, you could come upon a hefty concrete container lid.
Reasons to Hire a Contractor for Help
Attempting to locate a septic tank on your own can be risky, and in some cases, lethal, if the septic system is old and in danger of collapse. In the event that you fall into a cesspool, dry well, or septic tank, you will die. Removing septic tank lids on your own might potentially put you at risk of contracting bacterial or virus diseases. If you detect any of the following issues, please contact a contractor to assist you in locating or inspecting your septic tank:
- Soil that is sinking around the tank or drain field. Drainage backup into the home’s sewer system, or toilet backup
- A foul odor in the area where you assume the tank and drain field are located
- When there is no rain, pooling water, muddy soil, or spongy grass might occur. Septic tank covers that are rusted, cracked, or have been replaced with improvised lids are prohibited.
Even though you may be ashamed about forgetting where your septic tank is, it is a very frequent problem among homeowners. A contractor may assist you in locating it, and he or she may do it as part of the pumping service. If you need assistance locating your tank or if you have any other questions, please contact us at 503-630-7802. We are available to assist you!
How To Find a Septic Tank Location in an Old House (Tips and Techniques)
It is important for every homeowner to be aware of the location of their septic tank. It is quite beneficial for dealing with a variety of septic system difficulties. The septic tank can be difficult to identify in some older homes, which can be a major hassle if you are moving into one.
In this post, we’ll discuss the significance of your septic tank, as well as how to determine whether or not you actually have one. Following that, we’ll go through some of the measures you may take to locate a septic tank in an old house or property.
Importance of Locating Your Septic Tank
There are a variety of reasons why it is important for you to be aware of the location of your septic tank. For starters, it makes it easier to inspect and fix your septic system. Being aware of the location of your septic tank can also assist you with any future maintenance you conduct around the property. It is impossible to avoid damage to the tank and its associated lines unless you are aware of their location. If you hire a professional, they will be able to spend more time searching for your tank.
More information may be found at:
- How To Locate Your Septic Drain Field Lines
- Different Types Of Septic Systems (Which Is The Best For You? )
- How To Find Your Septic Drain Field Lines
How to Know if You Have a Septic Tank
If you have recently purchased a home, it is possible that you are unaware of the presence of a septic tank. The simplest method to find out is to look at your monthly water bill. Sewer services will not be charged if you have a septic tank, which will save you money. Additionally, the location of your home is an important factor to consider. If you live in a rural region, the likelihood that your home is equipped with a septic tank is rather high.
Where Can’t Your Septic Tank Be?
In the next part, we’ll have a look at the various strategies for locating your tank. But first and foremost, it’s crucial to note that there are several sites where your tank is not permitted. This will assist you in narrowing down your search.
Under Paved Surfaces
A tank is not permitted to be located beneath any paved surface. This refers to a driveway or a number of parking spaces.
In the House
Most individuals would probably consider this to be self-evident. Septic tanks are not permitted to be installed anyplace in your home. However, the tank is usually buried someplace outdoors, despite the fact that there are hints in your home that would lead you in the appropriate location. Can you image how bad that would smell?
Immediately Next to Your House
Most individuals would probably consider this obvious. Septic tanks are not permitted to be installed in any part of a home or building. However, the tank is always hidden outside, despite the fact that there are indicators in your home that will take you in the appropriate place. What a stench you might picture!
Under the Patio
The same line of reasoning holds true for installing a septic tank beneath your deck, patio, addition, shed or other structure. If you notice a building in your backyard, don’t even bother looking for your tank there.
Next to Your Well
It’s safe to assume that if you have a well, there is no tank in the vicinity.
Under Trees
Anyone who wants to plant trees should avoid doing so above or near to their sewage tank. Due to the age of your home, there is a possibility that this regulation will not be effective. After the tank was initially erected, it’s possible that someone came by and planted a tree decades later. The presence of a tree near your septic tank increases the likelihood of frequent blockages and other difficulties with your system. It is usually recommended to remove any trees that are in close proximity to your septic system.
How to Find Your Septic Tank
Anyone who wants to plant trees should avoid doing so above or near to their septic tanks. It’s possible that this guideline won’t work in your situation because your house is older. After the tank was initially erected, it is possible that someone came by and planted a tree.
If your tank is located beneath a tree, you should expect to experience frequent blockages and other issues with your septic system. In general, it is recommended to remove any trees that are in close proximity to your septic tank.
Look at the Drawings
Every septic system that has been installed with a permit has been documented with a drawing. These drawings are public documents, and you may obtain a copy of them by contacting the health department in your county. It may be more difficult to obtain the blueprints for certain older homes because of their age. However, it is still a smart initial step because it will provide you with the most precise information on where your tank is. These drawings show the location of your septic system, as well as a flow diagram and the components that make up your system.
Visually Inspect Your Yard
For the majority of folks, visual inspection of their yard is the most straightforward method of locating their tank. There are some clues to hunt for, so you get to pretend for a little while that you’re a detective on the case! You may expect the tank to be buried in your yard at some point. In older homes, the earth around the tank has had more opportunity to settle as a result of the passage of time. Here are several visible cues that indicate that you have located your septic tank: Grass that is more lush than usual Septic systems are responsible for releasing liquid waste and fertilizer into the surrounding soil.
- Some individuals opt to spend a few days without watering their lawn in order to see a more visible improvement in the quality of their grass.
- Grass that has died If you have a large patch of dead grass, this might be an indication that something is wrong with your tank.
- It might also be a sign of a problem with your computer system.
- See which area of grass thaws the fastest compared to the others.
- Spots of high or low pressure It is impossible to miss a little slope or pit in an otherwise level backyard.
Look at the Pipes
If you are unable to locate some hints outdoors, let us look inside. You are already aware that your plumbing drains into your septic tank, which implies that there is a line that runs from your home to the tank and back again. A pipe might be found in the crawlspace or basement of your home (typically 3-6 inches in diameter). It should be one of the only pipes that exits your home, and it has the strength to punch through a wall. This is the conduit that connects your tank to the rest of the house.
Exit your home and get to the area of your yard where the pipe is located immediately.
Because the pipe will be in a straight line, it will be simple to follow along with it.
Take a soil probe and follow the line to the end.
Concrete, polyethylene, or fiberglass are the most common types of hard, flat materials you’ll come across when looking. When you come upon a hard surface, congratulate yourself! The location of your septic tank indicates that you’ve struck gold.
Use a Pipe Camera
The usage of a pipe camera is a more high-tech alternative. This is a snake with a camera attached to the end of its tail. In order to see what’s going on, you may input the line into the machine. You’ll eventually reach your septic tank, at which point you’ll be able to exit the house and continue down the route. This also helps you to check whether there are any clogs or blockages in your line. The pipe camera also allows you to physically check the intake of your septic tank, which is an added bonus.
This product’s price and availability information will be presented on the product’s purchase page at the time of purchase.
Call a Pro
If all else fails, you may always hire an expert to assist you. They will be well aware of what to do and where to look. You could even witness them use some of the techniques described above, but these professionals will have access to equipment and expertise that is well beyond that of a typical DIYer.
Safety Tips While Searching for an Old Septic Tank
You should be on the lookout for a few additional safety dangers in your home because it is an older structure. If you see sinking dirt in locations that might potentially contain your septic tank throughout this operation, proceed with caution. Avoid going near these locations since it might be an indicator that your tank or system has collapsed, so stay away from them. Walking across these spots has the potential to cause you to fall through and into your tank, which is extremely dangerous and might be fatal.
Lastly, keep an eye out for any signs of rust on any portion of your septic system that you may come across.
You Might Also Like…
Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.
5 Ways to Find Your Septic Tank
1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.
3.
Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
When you do, that’s when your septic tank comes into play!
Look for the Lid.
You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
Those areas should be excavated in order to disclose the lids.
Get in touch with the pros.
Lifting concrete lids will necessitate the use of specialized equipment.
A fall into an unprotected septic tank has the potential to be lethal.
Produce your own diagram of your yard, which you may file away with your other important house paperwork.
That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!
