How To Install Septic Tank With Aeration Systems?

• The aerator gets placed right in the septic tank. It must get pushed right down to the bottom of your septic tank. Close the lid to your septic system. Wash and clean up thoroughly. You have just been working in an area that has millions of particles of bacteria.

Does a septic system need an aerator?

An aerator helps to push air into your septic system. Research has shown that when the air is introduced into the septic system, the air helps to break up waste faster. It also helps to give the good bacteria in your tank air that they need to survive, help them to thrive, and break up waste quickly.

What is an aerated septic system?

What exactly is a septic tank aerator? An aerator, or air pump, pushes air and oxygen into your septic system. The additional oxygen increases natural bacterial activity within the system, that then provides additional treatment for nutrients in the effluent.

How do I know if my aerator is working?

The surest sign your aerator has failed is an overwhelming unpleasant odor coming from where your system discharges, whether into a secondary treatment system or directly into the environment.

How long should an aerator run in a septic tank?

The aerator should run 24/7 nonstop and should not cost more than 10 dollars a month to run. If you electric bill is high something else is causing it or the system is not correctly hooked up.

How long does it take a septic aerator to work?

Most systems respond rather quickly, say within 4 weeks. The system will be fully functional during this period.

What is the difference between an aerator and a septic tank?

Aeration systems usually will have a septic tank or “trash trap” as the first treatment of the sanitary waste from the home. Therefore, sometimes the secondary treatment behind an aeration tank will be smaller in size because of the expectation of the water to be cleaner and easier for the soil to dissipate.

What size air pump do I need for my septic tank?

A typical septic aerator pump might run at 5 CFM or 80 LPM of air output. The typical range of septic air pumps for residential septic systems is about 2 to 8 cfm or from about 40 to 200 LPM of air.

How much is an aerobic system?

Aerobic systems are much more complicated than anaerobic systems and can cost between $10,000 and $20,000 to install.

How do you maintain an aerobic septic system?

Here are the dos:

1. Regularly Inspect Your Septic System.
2. Pump Out Whenever Necessary.
3. Be Water-wise.
4. Use Licensed, Certified Companies.
5. Flush Solids Down the Drains.
6. Pour Harsh Chemicals in Your Toilets.
7. Park Cars or Trucks on Your Drainfield or Reserve Area.
8. Add Septic Tank Additives.

Are aerobic septic systems good?

Aerobic bacteria break down waste solids faster than their anaerobic counterparts. The treated water that flows out of an aerobic septic system is cleaner, making an aerobic system a good choice if your property has a higher water table or other environmental challenges.

What is the purpose of aeration tank?

The biological treatment of the wastewater takes place in the aeration tank. Before the wastewater gets to this tank, it is mixed with activated sludge. This contains countless microorganisms, such as bacteria, that are able to break down the colloidal, organic contaminants dissolved in the wastewater.

How does aeration work?

Aeration brings water and air in close contact by exposing drops or thin sheets of water to the air or by introducing small bubbles of air and letting them rise through the water. Dissolved gases are then removed from the solution and allowed to escape into the surrounding air.

How to Install a Septic Aerator

A septicaeratoriis a relatively basic and straightforward piece of equipment to install in your septic system. The aerator is particularly beneficial for older septic systems since it contributes to the addition and provision of a significant amount of oxygen to the septic system. The presence of oxygen in the waste that flows to and from your septic tank is a critical component of the breakdown process. A professional can often complete the installation of this equipment in a matter of hours.

The procedure is, on the other hand, manageable and quite straightforward.

Step 1 – Familiarize Yourself with the Unit

As soon as you have acquired the sepic aeration system, you should bring out the instruction manual and go through the information that is contained within that particular item. Make certain that you have gone over all of the specifics. Learn about the parts, components, and factors that make up your new system so that you are comfortable with them. If you have any questions, you should contact with a specialist that specializes in the installation of these sorts of systems. Step 2 – Have the land surveyors come out and measure it.

1. A survey will be required if you wish to apply for a construction permit to install the septic system on your property.
2. Before you can start working on your septic system, you must first apply for a permit and submit a schematic of your system to the appropriate local government agency.
3. To find out who you need to contact in order to obtain the application, seek up the phone number or the location of your local township or municipality on the internet.
4. They will be able to point you in the direction of the application process.

Step 4 – Install a Riser and Lid Kit

If you do not already have a riser and lid kit installed on your septic system, you should purchase one. Install the kit first, then proceed to install the aerator. This will make it easier for you to acquire access to your septic system for future renovations and work. Each riser and lid set is unique in its own way. Make certain that the instructions provided by the manufacturer are followed.

Step 5 – Install the Aeration Pump

The aeration pump must be put at a reasonable distance of your residence. The pump is directly connected to the aerator (which was built in Step 3) and will assist in pumping in the additional oxygen that is required in the tank.

Step 6 – Install the Aerator

Installing the aeration pump in close proximity to your residence is required. Aerator (installed in Step 3) is directly connected to the pump, which will assist in pumping in the additional oxygen that is required in the tank.

DIY Septic Aerator? 4 Tips to Consider

With the aging and deteriorating of septic systems, a variety of difficulties may occur that can lead to backups in your septic tank and drain field, as well as standing water and other concerns in and around your drain field. Installing an Aero-Stream aeration system may frequently assist in improving the functioning of your existing system as well as resolving these issues in a timely and safe fashion. Using systems such as those supplied by Aero-Stream, you may improve the efficiency of your existing septic system without having to spend the money and time on a complete replacement.

The patented Aero-Stream Remediation technique has been copied multiple times, and several kits are available on the market that are copies of the original.

These methods do not allow for adequate settling of the solids in the tank, and as a result, the sediments will be discharged into the drainfield, causing even more issues than you already have.

Aero-Stream has spent the last 20 years refining their aeration system to the highest possible standard.

This technology has been rigorously tested and verified to meet the strict NSF 40 requirement for sanitation facilities. Here are four suggestions for properly installing your new aeration system and maximizing the efficiency and lifespan of your septic tank and drain field system.

DIY Septic Aerator – Read the instructions

Be sure to go through the installation instructions completely before you begin to verify that you have all the necessary tools and equipment on available. (See video for more information.) This can save you a significant amount of time and effort throughout the installation procedure. In certain circumstances, additional electrical cabling may be required in order to power your new aeration system; reviewing the installation instructions ahead of time will help to ensure that the entire operation goes smoothly and according to schedule.

Plan for future access

A septic tank riser kit, depending on the architecture of your current septic system, may be necessary in order to provide easy access to the aerator should septic system difficulties emerge in the future. Incorporating an access point for your new aeration system might make it easier to execute repairs in the event that they become necessary. When installed at the same time as the initial aerator installation, septic tank risers may be readily removed and reinstalled, allowing for more ease when performing future maintenance and repair activities.

Cover the wires

Self-installed septic aerator pumps are put above ground and are driven by electrical current. These systems, which are intended for outdoor usage, are safe and dependable when used as intended. Nonetheless, shielding or covering the electrical cables and outlets can help to prevent moisture and weather from causing damage to these critical components of the aeration system. While mowing the grass or completing other gardening duties around the house, taking this precaution will help you prevent accidentally damaging your electrical wiring and appliances.

Add a filter

Adding an effluent filter to the septic tank system during the installation process is a good option since it will help to reduce the quantity of solid waste that can escape the system during the repair process. Aeration may help avoid clogs and blockages in the output pipe, and it can also help to ensure that your freshly aerated septic system is processing wastewater and particle matter as efficiently as possible. If an effluent filter is being built, it is highly recommended that an aseptic tank riser be erected.

Using these four suggestions, you may considerably boost the efficiency and functionality of your current septic tank and drain field by introducing a sophisticated aeration solution that can significantly improve the efficiency and functionality of this critical household system.

Get The Best DIY Septic Aerator

A DIY septic aerator is something that you may try to put together yourself. You may assume you are saving money, but in the long term, you will be spending far more money than you saved. Purchasing an Aero-Stream septic aerator, which has been proved and patented, will save you both time and money. We have over 20 years of expertise and have installed tens of thousands of systems all around the world.

Your purchase will include free technical assistance as well as the highest level of customer care available anywhere in the world. Call our specialists at 877-254-7093 right away to schedule a free consultation. Alternatively, you may inform us about your system by emailing us electronically.

Changing From a Conventional Septic System to an Aerobic System

Changes to septic system laws are on their way for much of the United States, and they will have an impact on many homeowners who have traditional septic systems. When a septic system becomes old and/or poorly managed, the owners of these systems may be faced with the option of shifting to an aerobic treatment procedure. Many property owners around the country have informed us that they have been asked to convert or replace their existing septic treatment systems with an aerobic treatment system, which we believe is correct.

Aerobic and septic treatment methods are two distinct types of treatment processes.

In this case, “aerobic treatment system” (ATS) or something like would be more appropriate.

• When it comes to septic tanks and aerobic septic systems, what is the difference between the two? What are the benefits of converting a septic tank to an aerobic septic system
• In what way does one go about changing a septic tank into an aerobic septic system?

What is the difference between a septic tank and an aerobic septic system?

Whether there is air or not, Simple answer: an aerobic septic system, also known as an aerobic treatment system, employs air supplied into the water being treated to support aerobic bacteria or microorganisms that devour contaminants present in the wastewater. A septic tank makes use of anaerobic bacteria, which do not require oxygen to survive, in order to devour the toxins present in the wastewater. Bacteria that are aerobic vs anaerobic In comparison to anaerobic bacteria, aerobic microbes absorb contaminants more quickly and thoroughly.

1. Equipment From the standpoint of equipment, a septic system is far less complicated than an aerobic treatment system.
2. The tank will be equipped with a number of access points for inspection and pumping.
3. An aerobic treatment system, like an anaerobic treatment system, is primarily comprised of a single tank that is separated into many chambers.
4. For this purpose, extra equipment such as mixers, air compressors, media, and other ways will be required.

Why convert a septic tank to an aerobic septic system?

There are a variety of reasons to switch from septic to aerobic systems:

• Changes in permit regulations that mandate the conversion from a septic system to an aerobic system Drain field circumstances necessitate a more intensive degree of treatment than that provided by aerobic therapy. an ardent desire to preserve the environment Drinking wells and an aquifer are in close vicinity

Overall, an aerobic treatment system is beneficial if you want better treatment of your sewage and to increase the quality of the water that you are re-introducing into the ecosystem.

Please keep in mind that the water that you put back into the ground ultimately comes out of your tap (particularly if you use a well for drinking water).

How do you convert a septic tank to an aerobic septic system?

Briefly stated, an aerobic treatment system is the most effective way to increase the treatment of your sewage as well as the quality of the water that you return to the environment after use. Recall that the water you put back into the soil will ultimately come out of your tap (this is especially true if you utilize a well for drinking water).

1. Improve the efficiency of your current septic tank by installing technology that allows it to employ aerobic microorganisms. Removing your septic tank and replacing it with an aerobic treatment system is the best option.

This blog entry is primarily concerned with the treatment system itself; it does not discuss the drain field or any concerns that may arise in connection with drain fields. Drain fields that are blocked or damaged must be treated separately from the rest of the plumbing system. Your drain field will not be repaired simply by switching from septic to aerobic treatment! Option 1: Converting a septic tank to an aerobic treatment system by installing additional equipment. There are systems available that may be put in a septic tank to convert it to an aerobic treatment process, which is more environmentally friendly.

1. By introducing air, however, we will also be mixing the contents of the tank, which means that solids that would normally be sat at the bottom of the tank will now be whirling about the tank when the air is introduced.
2. If you have a septic system that has numerous compartments, you should add air to the upstream (first) compartment and use the downstream (second) compartment for settling the wastewater.
3. If you have a pump tank for your drain field that is located downstream of the septic tank, that tank might be utilized for settling.
4. Adding healthy bacteria to the water after the aeration system has been built is something we recommend.
5. Option 2: Eliminate your septic tank completely and replace it with an aerobic treatment system.
6. Not only that, but it is also the most entirely successful path to take.
7. Depending on your needs, you may optionally add additional components to the treatment system that improve the quality of the water entering and exiting the system.

The footprint of an aerobic treatment system should be fairly comparable to the footprint of the septic system that it is intended to replace.

FAQs About Septic Tank Aerators

It’s possible that you’ve recently moved into a home that has an aeration system or an aerated septic tank, or that you’re looking to install a new ATU to repair your current septic system, that you’re looking for answers aboutseptic tank aerators. If this is the case, you’ve come to the right place. Depending on where you reside and what state you live in, an aerated septic system is referred to by a variety of various names: Aerobic Treatment Unit (ATU), aeration system, septic aerator, advanced onsite treatment unit, and other terms are used to describe these devices.

The septic tank aerator is sometimes the sole moving item in the whole system.

As a result, you want to make certain that it is constantly working smoothly and that it is regularly maintained.

1. Aeration systems and aerated septic tanks are common in modern homes. If you’ve recently moved into a home that has an aeration system or an aerated septic tank, or you’re looking to install a new ATU to repair your current septic system, then you may be looking for information on septic tank Aerators. Depending on where you reside, an aerated septic system is known by a variety of distinct names: Aerobic Treatment Unit (ATU), aeration system, septic aerator, advanced onsite treatment unit, and other terms are used to describe various types of wastewater treatment. Every one of these terms refers to patented wastewater treatment units that have been approved by a regulatory authority and that employ an air pump or other mechanism to inject air into the tank that contains the wastewater. Sometimes, the septic tank aerator is the sole piece of equipment that moves in the whole system. Your wastewater is processed and your drainfield is protected by this component, which serves as the system’s heart. Thus, you want to be certain that it is constantly in good working order and that it is well maintained. Continue reading for answers to some frequently asked questions about septic aerators.

Contact HIBLOW for Septic Aerators!

It’s possible that you’ve recently moved into a house that has an aeration system or an aerated septic tank, or that you’re wanting to install a new ATU to fix your present septic system, that you’re looking for answers aboutseptic tank aerators. If so, you’ve come to the right place. Depending on where you reside, an aerated septic system is referred to by a variety of different names: Aerobic Treatment Unit (ATU), aeration system, septic aerator, advanced onsite treatment unit, and other terms are used to describe these systems.

Most of the time, the septic tank aerator is the sole moving component in the whole system.

As a result, you want to make certain that it is constantly working well and that it is properly maintained.

Septic system failed – should I try installing an aeration unit?

In the previous couple of weeks, I’ve made significant strides forward in my circumstance. My leach field was around 95 percent obstructed, with very little, if any, movement in the water. I had already moved the graywater to another solution, which had been beneficial for a time, but the field began to fail gradually, eventually failing to the point of being virtually unusable. I have a single septic tank and wanted to experiment with aeration without incurring the expense of a second tank. I discovered a number of things that I haven’t seen openly stated on any of the boards, so I wanted to share them here in the hopes that it would be of use to someone else.

• Too much air volume was introduced into the tank, and it was placed in the middle of the tank, causing excessive churning and sediments to escape the tank.
• I was under the impression that it didn’t work for a number of months.
• However, in the last couple of weeks, I’ve noticed that the water levels have really dropped to the point that they are STAYING at the edge of the output pipe!
• I utilized the approaches outlined below to prevent having to replace my field without spending $1000 on a solution.
• They must pass through the first baffle and separate in order for the lighter stuff to ascend and the heavier materials to descend through.
• If you look about, you can find diaphragm diffusers for as little as $35 that can be attached to PVC pipe and activated by an air valve that supplies JUST ENOUGH air pressure/volume to activate the diaphragm (this is an air RELIEF valve, not a cutoff valve).
• If you use too much, you’ll get a torrential downpour (which you don’t want).

Everything may happen away from where the tank is settling, which saves time and energy.

In addition, I received a 4 “On the output side, there was a TEE that acted as a divider.

You don’t want bubbles to rise into the TEE, since this might cause some debris to be drawn into the TEE.

When it comes to my solitary concrete tank, one idea I had from a local contractor was to empty it, climb inside, and create a cinderblock wall that would allow for two-thirds incoming/settling and one-third aeration.

There is a requirement for several hundred gallons of aeration space.

If you can find a method to open the other end of your leach lines in order to expand your field, even temporarily, you will be able to move this newly invigorated aerated bacteria through there more quickly, allowing it to begin to work sooner.

It is important to note that I did not need to purchase super duper amplified bacteria to add.

That’s analogous to purchasing weed seeds: if you give dirt enough rain, the weeds will appear.

My findings show that the low agitation treatments available for $500-$1000 that are already on the market would almost likely work. I just choose to experiment with a do-it-yourself option. I hope this is of use to someone.

Can we install an aeration unit in an older septic system?

I’m writing to you nine years later, hoping that your situation has been handled. As soon as I saw the year 2013 on the calendar after I had developed a response, I decided to practice saying it. Sewage backup may be quite distressing. Here are some of my personal thoughts. When sewage comes up via your shower drain, it indicates that there is a full blockage in the system since the raw sewage has nowhere to flow. If it was leaking through the earth that covered your stone ditches, it might have created an offensive-smelling moist environment.

1. This box is located underneath the septic tank and is utilized if you have more than one trench for your septic system.
2. Finally, it was coming up from the drain in your bathroom.
3. Is that place squishy and dripping wet?
4. Yes, a new field can be quite expensive; however, if a different reason can be identified and resolved, the day may be saved.
5. Last but not least, when people discover that the septic tank is full of liquid, they are understandably alarmed.
6. Septic tanks are designed to hold settalable solids for later disposal.
7. They decompose due to anaerobic activity (lack of oxygen), bacteria consumes the solids, and they get smaller.

The exit of a septic tank is several inches lower than the entry of a septic tank.

It is necessary to pump them out in order to guarantee that the thickness of collected and degraded solids does not reach a depth that would enable raw solids to flow out of the discharge port.

In the context of waste management, effluent is classified as a secondary waste, meaning that it can be further treated by passing downhill through a few feet of drier soil.

Long trenches were created in order to provide the amount of space required for the amount of water that a residence consumes.

Septic fields were initially used in a systematic manner in the 1960s.

At the time of their introduction, there was general agreement that it would take approximately 30 years before all households would be serviced by Municipal Sewerage Collection and Treatment systems, therefore eliminating the need for all septic field systems.

Aeration Septic – The Top Five Items to Keep Out of Your Septic System

Despite the fact that there are several alternative ways to dispose of trash within the home, some people just opt to use their toilet or garbage disposal for materials that do not belong in these pieces of equipment – which may put their septic system at risk. There are certain things that a toilet is supposed to handle and rid of, such as body waste, particular paper products, and the occasional spider that gets tangled in toilet paper, but there are other items that people flush that can cause far more harm than good.

You might believe that “if it flushes, it’s alright,” but this isn’t always the case, even when it comes to goods that are advertised as safe to flush as a form of disposal.

What is a septic system?

In spite of the fact that there are several alternative options for disposing of trash within the home, some individuals just prefer to use their toilet or garbage disposal for materials that do not belong in these pieces of equipment, which may endanger the septic system. There are certain things that a toilet is supposed to handle and rid of, such as body waste, particular paper products, and the occasional spider that gets tangled in toilet paper, but there are other items that people flush that can cause considerably more harm than good.

However, even when goods are promoted as being safe to flush as a form of disposal, this isn’t always the truth, as evidenced by the fact that many things aren’t.

This is true for a variety of reasons, including the fact that it’s easier to remember.

Here’s a list of the top five things you should avoid introducing into your home’s septic system:

• Coffee grounds: While coffee grounds are not flushed, they frequently make their way into a garbage disposal and, ultimately, into the septic tank. Because of their texture, bacteria have a tough time breaking them down, which can put your septic system in risk over time as they accumulate. One excellent comparison is to think of these grounds as if they were gravel, despite the fact that they are far smaller. In the long run, the number of coffee grounds that do not decompose will contribute to an increase in the amount of solids (or sludge) present in the system, which might cause it to malfunction. Strong disinfectants, such as bleach: Because a properly functioning septic system relies on beneficial bacteria to break down waste, introducing these sorts of chemicals into the system in excessive quantities can be detrimental to the system. The weekly cleanings and the introduction of these chemicals into the toilet bowl insert in tiny amounts per flush are both perfectly acceptable practices
• Nevertheless, the use of excessive amounts is not encouraged. A decrease in the quantity of bacteria present in the holding and treatment tanks, which is a “living system,” might lead to an increase in the amount of solid waste accumulating in the system, which may necessitate more regular visits from a septic services specialist. Contrary to popular belief, condoms, disposable diapers, flushable wipes, and tampons are not as safe to flush as you may assume. Due to the fact that rubber does not degrade within the system, flushing condoms may put a septic system at risk of failure. Although the materials that are used to manufacture disposable diapers and tampons are termed biodegradable, this does not imply that they are beneficial to the general health of the system. However, while they will ultimately fail within the system, it may take a long time for them to do so, resulting in these objects remaining in the system for extended periods of time and causing further problems. Is it one of these other problems? These huge things have the potential to block pipes or become caught around the motor of a septic system, leading it to fail. A septic motor is a high-priced device that will normally cost upwards of $600 to repair or replace. Is taking this chance worth it? Grease and oil derived from the cooking process: Despite the fact that it may appear simple to simply drop these items down the drain while cleaning pots and pans, they may cause more harm than good. Although some oil and grease can unavoidably enter a septic system, an excessive amount of this will undoubtedly cause difficulties over time, especially in older homes with older septic systems. What is the explanation behind this? Over time, these materials have a tendency to harden and solidify, making it more difficult to break them down. The particles may also become attached to the sides of the pipes and walls of the septic tank, as well as to the moving mechanisms within it, causing backups, blockages, and overflow – or even a breakdown of the aerator or any other affected sections. Medications: Additionally, drugs have the potential to kill the bacteria that must be present in a septic system when they are flushed, and in some cases, they do so. This does not just apply to unused tablets
• Liquid drugs should never be flushed down the toilet too. Many of these prescriptions contain high amounts of antibiotics, and when these pills are flushed down the toilet, the chemicals in these medications will disrupt the delicate balance that must exist in the tank. Another item to take into consideration? If there is a problem with your septic tank – such as an undiscovered leak – these chemicals will be released into the environment as well, and this is harmful.

There are methods for disposing of all of these things that are not limited to the sink or toilet, and homeowners should consider taking advantage of these possibilities. Even if it means that garbage bags will fill up fast or that an empty jar will be required to collect grease, making these decisions will save you time, concern, and most likely a significant amount of money in the long run. Septic system maintenance is neither difficult nor prohibitively costly as long as you follow the instructions of septic service specialists.

For those who have not complied with suggestions and may have introduced items such as these into their system?

Don’t be scared to ask about the many septic system treatment alternatives accessible to folks who need to reintroduce healthy bacteria into their systems while also eliminating some of the known concerns.

For more information on how to properly maintain your home’s septic system, call Aeration Septic at (330)791-3226 to talk with a knowledgeable representative and book an in-home consultation with an expert.

Aeration Septic – Certified Hydro Action Septic Providers

We provide a Septic Maintenance Contract, under which we will be glad to maintain your septic system through two site visits each year on your behalf. Our service technicians will completely examine the septic system during these visits to verify that all components are functioning correctly and effectively. We will notify the health department that we are servicing your system and will ensure that you are in full compliance with all applicable laws and regulations. We will also offer a sludge judge, which will measure the contents of the tank, allowing us to eliminate the guesswork involved in determining when the system should be flushed.

We forgo our $95 service call charge for contract clients in the event that any repair work is required, and we give discounted prices on any components that are required to get the system back up and operating again.

has been in the business of installing, repairing, and maintaining septic systems for more than three decades.

Septic Aeration – Septic Tank Problem Solved with Our Septic Aerator

The procedure is not hindered by high temperatures at any point during the process. The aerator is equipped with a fan to keep it cool even in high temperatures. Aeration systems for septic systems are being erected all throughout North America, from Arizona to Alaska and Canada, where temperatures can drop below -40 degrees Fahrenheit and there is feet of snow cover during the winter. Our septic aeration systems are not adversely affected by these harsh weather conditions.

Do I need any special tools to install one of your Septic Aeration Systems?

To do this project, you will need a garden shovel, a 5/8-inch drill bit and drill motor, and a small bottle of silicone caulk, assuming you have an outside outlet (power source).

I hear a gurgling sound when I flush the toilet

When this happens, it indicates that the pipes are not draining correctly. A blockage in the pipe might occur either before or after the septic tank is installed. Remove the septic tank cover and check to see if the level in the tank is greater than the level in the baffle. If it is, the blockage is located there. The blockage might be anywhere between the home and the septic tank if this is not the case. A mature biomat that has to be removed using the Septic System Saver® aerator is most likely present if your septic tank level is high.

Will I have to touch or come in contact with sewage when I install one of your septic aeration systems?

In most cases, if the septic aerator is properly placed, you should not come into touch with any waste water. When you remove the clean out lid from the septic tank, you will notice a strong stench of septic waste.

Do I need to pump the tank before installing one of your septic aeration systems?

If you decide to place the product in your septic tank, we recommend that you pump the tank prior to installing the device.

Do I need to pump the tank out while one of your septic aeration systems is working?

You should not have to pump the septic tank any more frequently than you did before the septic aerator was installed in the tank.

After around 30 percent of total tank content has been reached by solids, we recommend that you pump out your septic tank and replace it with new solids.

My septic pumper told me that I have a problem with septic water running back from my drain field. What does he mean?

It’s possible that he’s referring to two separate concerns. The vent pipe should be terminated at a height of at least 12 inches above the ground. Rainwater will not be able to enter the septic system through the vent system as a result of this. According to him, the other problem was that when pumping the septic tank, he noticed effluent leaking backward into the septic system from the drain field. A saturated drain field means that the septic effluent cannot be disbursed as quickly as it is received by the septic system, and this indicates that the drain field has become clogged.

This problem will be resolved by our septic aerator.

How do I know if my septic system is failing because of a clogged biomat?

The biomat in the great majority of septic systems becomes blocked, resulting in the system failing. Hire a pumper to inspect your system and establish whether any effluent is returning to the septic tank while the system is being pumped. Instruct them to estimate the amount of effluent that returned to the tank. If it is a tiny quantity, it is possible that a clogged pipe exists between the tank and the field. If there is a significant amount, there is a good possibility that the biomat is clogged.

How do I know if my septic system is failing?

In certain cases, you may notice effluent ponding on the surface of the ground, as well as smells from the septic system, gurgling pipes, sluggish flowing drains, or backups. When the system is being pumped, it is possible to encounter back flow from the field.

I have a septic odor in my back yard. Will your septic aerator fix this?

Yes, the Septic System Saver® aerator will completely eradicate the stink from the system. The presence of a septic odor in your yard indicates that wastewater has either reached the surface or is very close to the surface. A walk around the region of your yard where the septic system is installed is recommended. Look for spots where the grass is more lush or greener than the rest of the lawn. If you come across an area like this, the most likely reason for it is the establishment of a clogged biomat.

Can I speed up the process?

In order to accelerate the restoration process, water consumption must be reduced, as well as the use of chemicals that are flushed down the toilet. Unless your behaviors are very harmful, you should not be required to change them! Simple actions like turning off the water while brushing your teeth, keeping a container of drinking water in the refrigerator, and spacing out laundry loads, among other things, should be done to ensure that your water fixtures are not leaking before they become a problem.

My septic pumper tells me I need to install a new field

Others have told us that local septic system suppliers have informed them that the only answer is to rebuild their drainage field. We have received several reports like this. Many tens of thousands of dollars are required to implement this solution. There is also the possibility that your whole drainage system may be condemned during the permission procedure for a new drainage bed and will have to be replaced with extremely expensive systems such as a mound system or a holding tank.

This isn’t the case at all. Please contact us by phone at (800) 969-8792 or by email at for an eFREE consultation!

Will the Septic System Saver® septic aeration system work on all septic system types?

Others have told us that local septic system suppliers have informed them that the only answer is to completely rebuild the drainage field. Several thousand dollars will be spent on this solution. The possibility exists that your whole drainage system will be condemned during the permitting process for a new drainage bed and will be replaced with extremely expensive systems such as a mound system or holding tank. This isn’t the case, unfortunately. You can reach us by phone at (800) 969-8792 or by email at for an eFREE consultation.

Septic Tank Installation and Repair

Zuech’s Environmental Services Inc. is a company that specializes in providing timely, efficient, and professional service on each and every assignment. With excellent supplies and appropriately qualified employees, we believe in getting the work done perfectly the first time, every time. Zuech’s Environmental Services Inc. installs the following products and components:

• Nayadic aeration systems
• Complete septic systems
• Septic tanks and absorption beds
• Septic tanks and sand filters
• Complete septic systems Replacement of a septic tank
• Installs and repairs equipment.

Additionally, in addition to septic tank installation services, we also provide a variety of septic tank repair services. All components of your septic tank must function properly in order to provide the best possible outcomes for your wastewater. If a single object is cracked or damaged, it has the potential to cause significant damage in the future. We provide a wide range of repairs, including the following:

• Baffle replacement
• Line repair or replacement in and out of the septic tank
• Replacement of the D-Box

Zuech’s Environmental Services Inc. is the Nayadic Aeration Systems authorized reseller in the counties of Cattaraugus and Chautauqua in southern New York State. We sell, install, and give yearly service agreements to ensure that the system is in perfect working order at all times. The following services are available: sewage and water line installation: If you live within a village and are connected to municipal sewer and water, we can repair and or replace your lines as needed. We are capable of identifying, evaluating, and repairing a wide range of drain line issues.

It is not necessary for sewer line rehabilitation to be associated with the destruction of yards or driveways.

Trenchless pipe repair essentially eliminates the disturbance and mess produced by standard pipe repair procedures, which involve trench digging to complete the repair.

Jet™ Aeration Systems

The cost-effectiveness, dependability, and durability of the JetTM Aeration system make it, without a doubt, the most cost-effective and long-lasting option for wastewater treatment.

What is the difference between a Jet™ Aeration system and a septic system?

An Aeration system such as the JetTM Aeration system treats wastewater by using aerobic bacteria, which is a more efficient method of treatment. This treatment is comparable to the way municipal sewage facilities handle the wastewater generated by the general public. Because they are so energy efficient, Jet Aeration systems generally cost the homeowner less to operate than the majority of their major household appliances, such as the television and refrigerator, over the course of their lifetime.

Due to our position as Licking County’s only licensed distributor of JetTM Aeration systems, we are able to not only install your JetTM Aeration system, but also repair and maintain it, guaranteeing that it is in proper working order during the whole day. This includes the following:

• Installation of JetTM Aeration systems
• Sales of JetTM Aeration parts
• Repair of JetTM Aeration motors
• And JetTM Aeration maintenance (service contracts).

Our company is authorized to service your Jet system in the counties listed below.

LickingDelawareTuscarawasMorrowGuernseyMarion

KnoxFairfieldAshlandWayneUnionHolmes

FranklinPerryCrawfordFranklinHarrisonCoschocton

MansfieldOntarioRichland

Owner’s Manual for the JetTM 1500 Series Bat® Media Plants is available for free download. Instruction manual for the JetTM Wastewater Treatment Solutions 1500 Series Bat® Media Plants (included).

Is My Aerobic Septic System Supposed to Run All the Time?

7:00 p.m. on May 23, 2019 One of the most often asked concerns we have from our clients is if their aerobic septic system is meant to be operating all of the time. The answer is both yes and no. The vast majority of septic systems are equipped with air compressors that are continually running. Some companies, like as Norweco, do, however, provide an Aerator that is meant to operate for 30 minutes on and then 30 minutes off. The inquiry itself seems to reflect a lack of understanding of how septic systems are meant to work in their most basic form and function.

1. Here is some information to take into consideration.
2. The tank is normally rectangular or cylindrical in shape, and it is composed of concrete, polyethylene, or fiberglass in most cases.
3. During the disposal process, the particles that enter the septic tank float on top of the water where they interact with beneficial bacteria and begin to decompose.
4. Septic tanks are available in a variety of configurations, including double-compartment and single-compartment configurations.
5. It still carries pathogens, contaminants, and organic waste despite the fact that it has undergone some treatment.
6. Accordingly, wastewater shall not be dumped onto the ground’s surface or into any surface or ground water.
7. The drainfield should be suitably covered with grasses or shallow-rooted plants to prevent erosion.
8. Its capacity to function as an efficient filter may be compromised if the soil is contaminated.

Think about how frequently you use your home’s water sources, together with how long it takes for bacteria in the system to react with the solids over a lengthy period of time, and you’ll see why the system must be running at all times, not only to keep it running but to keep it running properly.

Get in touch with Countryside Construction Inc. now to discover more about the inner workings of your aerobic septic system in Canyon Lake and the Foothill Communities of Texas! Aerobic Treatment Systems are a subcategory of this category. Admin is the author of this blog article.

Waste Water Treatment

• Dosing tank must be at least 1000 gallons in capacity. Automatic or manual head works box or distribution valving are both options. A wastewater pump that is sized appropriately for the field and positioned in the dosing tank
• When the effluent pump is activated, the control panel regulates the frequency and duration of pump operation
• It also includes an audio-visual warning to warn of excessive water levels. Sch 40 PVC pipe is often utilized for distribution from the dosing tank to the drip field and is 1 inch in diameter. In order to enable the field to drain between dosings, vacuum breaks must be installed. Drip tubing, the amount of which varies depending on the use

Normal plow depths range from 6″ to 10″ and are achieved by using a specialized plow made specifically for this purpose. The design of a system is not difficult. Each design parameter is listed on a work sheet, and a computer software with easy-to-follow sizing instructions is included as an additional bonus. It is necessary to use clean Class I effluent in this system, which must be preceded by an aeration system. When there is no secondary filtration in the aeration system, an effluent filter such as the NORWECO BK2000 should be installed after it.

Extra protection will improve system performance and prevent back flushing on the emitters in the drip field as a result of the addition.

Obtaining this information is essential in order to appropriately design and situate the proposed irrigation field.