- Apply liberally around the bases of the risers with a trowel, completely sealing the edges to the top of the septic tank. Allow to dry completely. Bolt the lids onto the risers according to the manufacturer’s directions, using a socket wrench. Cover the septic tank with soil.
Can you replace the lid on a septic tank?
Concrete septic tank covers require replacement when they develop cracks or other damage. These can be purchased online or at a home improvement store near you. Many septic tanks have risers so the lid is visible above ground.
Should a septic tank lid be covered with dirt?
The lid covers should fit tightly — if they don’t, a company that specializes in septic repairs should be called to fix them. A septic tank stores the solids from drains and needs to be pumped out about every two years, so it’s not a good idea to cover the area — you need to always be sure where to find the tank.
Should you cover your septic tank?
You should cover your tank up with something that can be easily moved when you need to move it. Animals Need to Stay Away from Your Septic Tank System: Keep animals away from your septic system. It is not a good idea to grow a vegetable garden to cover up your septic tank pumping system though.
How thick is a septic tank lid?
The exterior walls of the septic tank are made of concrete, normally 4 inches thick. The concrete is either a minimum of 4,000 or 5,000 PSI concrete.
How do you remove a septic tank lid?
Some tank lids have built-in handles to pull on, but others require a pry bar to lift them open. If the lid comes with handles, ask for the assistance of a friend or family member to remove the lid. If it doesn’t, push a screwdriver into the seam around the lid and insert the pry bar into the gap. Then, press down.
Do septic tanks need to be airtight?
Septic tanks need to be watertight. The riser should be sealed to the top of the tank and the riser cover should be sealed to the riser with butyl rubber or some other flexible sealant. No liquid should enter or leave the tank.
Should I install a riser on my septic tank?
Having a riser in place can also significantly reduce the cost of septic tank maintenance over time through the ease of access and time on the job saved. Plus you will be spared digging up your lawn every time as well.
How many lids are on a septic tank?
A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.
Does homeowners insurance cover septic tank collapse?
Yes, your septic tank is considered part of your home and would be covered by the dwelling coverage portion of your home insurance in the event that it is suddenly damaged.
How far apart are septic tank lids?
The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.
How deep is a septic tank cover?
In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid.
Installing Access Risers
In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below. Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.
A few safety tips before you get started:
- Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website
- Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.
Gather all the MaterialsTools You will Need
It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.
Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.
Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.
See below for Step 4 on attaching risers to the tank entrance.
- Tank Adapter Ring (TAR)
- Riser Adapter Ring Kit
- Butyl Rope
- Risers
- Domed Lid OR Flat Lid
- Stainless Steel Screws
The following materials will be required for digging up your septic tank(s):
- Digging up your septic tank(s) will require the following materials.
To cut risers to the proper size, the following tools are required:
- Circular saws, saber/jig saws, and hand saws
- Raspor file
- Marking pen
- Tape measure
- Drill with a 1/4″ bit
Materials required to seal the risers to the tank include:
- High-strength concrete patch mix
- A small bucket
- A mixing stick
- And gloves
Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.
Step 1: LocateYour Septic Tank(s)
When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.
Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.
The presence of underground electricity or other utility lines and cables might put your septic tank in danger.
If you run into a power line, the consequences could be fatal. Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.
Step 2: Uncover Your Septic Tank (s)
Once you’ve discovered your septic tank, you may start digging about. The tank is typically 6 feet wide by 8 feet long, with the width being the largest size. Remove all of the pebbles and debris from around the tank’s lid openings and dig out the whole top of the tank. You will want to clean out any dirt that has accumulated on the surface of your septic tank. This will assist you in ensuring that you generate a high-quality seal. You should have two openings: one over the inlet (which comes from the home) and another over the outlet (which comes from the yard) (into the drainfield or pump chamber).
- You’ll need a riser for each of the doors you open.
- Typically, the inlet side is the one that is nearest to the home.
- When cleaning the tank, it is beneficial to remove the complete top of the tank.
- Risers must be modified in order to be correctly installed, and all manholes (holes 24 inches or bigger in diameter or square in shape) must also be updated, as well as the tankinlet and outlet baffle covers (if separate from the manholes).
- If you discover one – and only one – riser already installed, it is most likely for the pump chamber, which only requires a single riser to provide access to the pump to function properly.
- Remove the concrete lids so that they may be disposed when the project is completed.
- Consult your’As-built’Recorddrawing to establish whether you have a distribution box (D-box), which you will also need to unearth and place a riser on if you have a typical gravity system.
- Once the lids have been removed, proceed with caution around the tank.
- Inform someone of your whereabouts in case you are involved in an accident.
You should be aware that exposure to sewage can result in serious sickness, so make sure you wear gloves and thoroughly wash your hands afterward with soap and water. It is also recommended that you wear eye protection in the event that debris falls into a tank and splashes back at you.
Step 3: Fit Risers to Component Openings
In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:
- Theriser will fit into the tank hole if the aperture is between 26 and 29 inches in diameter. Measure the distance from the ground to the top of the septic tank and multiply the measurement by three inches. The following is required if the aperture is greater than 29 inches: a 3-foot square fiberglass plate (with a 22-inch hole in the middle) is required. In this case, it lies above the manhole and narrows the aperture, allowing a 24-inch riser to be utilized instead of a more expensive 30-inch riser, saving money.
The distance between the ground and the top of the fiberglass plate should be measured. You may choose to place the risers so that they are level with the surface of the ground, or you may want them to stand out a few inches above the ground (if a riser is above ground make sure you are careful when mowing). Tips: To shorten a big riser with ribs, drill a 1/4-inch hole between the ribs above the cut line and finish the cut by following one of the grooves between the ribs with a saber/jig saw to finish the cut.
By eliminating one of the ribs from the largeriser, it may be made to fit more snugly into a smaller manhole entrance.
Step 4: Attach Risers toSeptic Tank (s)
It is recommended to pump out an old septic tank that is 20 years or older in order to check its structural integrity and water-tightness before using it again. If the tank requires extensive repairs, it is preferable to replace it with a new septic tank that includes risers as part of the installation. A permit from the local health department is required for the replacement of a septic tank. Remove any dirt and debris from the tank’s surface by cleaning it off. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s instructions.
- Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names available.
- NOTE: For optimal results, just a little amount of concrete patch should be mixed at a time.
- The patch mix should be used to seal the riser to the septic tank.
- If you want to avoid a safety danger, make sure you properly attach theriser lid using the screws that come with it!
- Risers for inlet or outlet apertures that are smaller than the openings should have the bottom few inches sanded with rough sandpaper to allow a firmer connection between the two surfaces.
- A useful source of information on correct installation of risers on septic tanks may be found at your local hardware store where you purchased the risers and covers.
Thurston County Environmental Health is should be commended for providing the foundation for this documentation.
How To Instal Risers On A Septic Tank
A septic tank riser system will be installed today, and we will demonstrate how to do it. If you have a concrete septic tank that does not have risers built, this instruction is for you. It is currently mandatory in many areas to have risers and lids installed on your septic tank. When it comes time to have your septic system pumped out, installing a riser system can also save you money. Please follow the instructions in the following section and you will have no difficulties.
Step 1 – Gather The Parts You Need
The following things will be required for the installation of a riser system on your septic tank. (Click on the item to make a purchase.) Tuf-Tite Tank Adapter Ring (optional) (TAR) 2)Riser Adapter Rings Kit (includes riser adapter rings) Butyl Rope (number three) Tip-Tite Risers are a type of tie-down device. 5)Tuf-Tite Domed Lid (optional). ORTuf-Tite Flat Lid (Ortuf-Tite Flat Lid) 6) Screws made of stainless steel Keep in mind that you will have to determine the size of the hole in your septic tank.
Consider this: If the hole in your septic system is 22 inches across at its widest point, you will need to purchase the 24 inch Tank Adapter Ring, 24 inch Risers, and 24 inch Lid.
Step 2 – Clean The Top Of Your Septic Tank
The following materials will be required in order to construct a riser system on your septic tank: If you want to purchase something, simply click on the image. Tuf-Tite Tank Adapter Ring (optional) 1) (TAR) Riser Adapter Rings Kit (Set of 2) Rope made of butyl Tite-Risers are a type of tie-down device. Tuff-Tite Domed Lid (optional). A Flat Lid made of ORTuf-Tite is a type of lid that is made of rubber. screwed into the surface of the stainless steel Remember to measure the size of the hole in your septic tank before you begin the repair.
Example: If the longest point of the hole in your septic system is 22 inches across, you will need to purchase the 24 inch Tank Adapter Ring, 24 inch Risers, and 24 inch Lid.
Step 3 – Apply Butyl Rope To Tank Adapter Ring
To secure your Tuf-Tite Tank Adapter ring to the bottom of your tank, tie a butyl rope ring around it. This will aid in the creation of a water-tight seal. Make sure the butyl stretches all the way around the Adapter Ring before you tighten it.
Step 4 – Put Adapter Ring Around Hole And Screw It Down
Firmly push the Tuf-Tite Tank Adapter Ring onto the septic tank’s adapter ring to secure it. To begin drilling the holes, use the drill bit that included with the package. The Adapter Ring will have divots in the areas where the holes will be located. Once you have pre-drilled the holes, you may use the blue concrete tapping screws that are provided to secure the ring to the top of your installation system.
Step 5 – Add Butyl Rope To The Bottom Of Each Riser
The bottom of each riser will have a recessed ring in the center. In this ring, insert a strip of butyl rope and tighten it. This will ensure that the risers are watertight.
Step 6 – Put Risers and Lids On The Adapter Ring
Each riser will have a recessed ring at the bottom of it.
This is where you’ll insert a strip of butyl rope. This will ensure that the risers are watertight for the foreseeable future.
How to Install Risers and Lids on Concrete Septic Tanks w/ Square Hole
Posted on the web by Installing risers and lids will make it much easier to get access to the septic tank for inspection, repairs, and pumping. There is an up-front expense, but that cost can be compensated over time by the cost of locating and digging every time you require access to the tank, which can add up over time. Determine the height of the riser. Tank risers are normally installed around 3 inches above the ground’s surface temperature. Having the lid at ground level will make it simpler to locate; however, some people prefer to have the lid a few of inches below ground level so that it is easier to mow over and less noticeable while in use.
- The height that is chosen is entirely a matter of personal taste.
- Begin by digging all the way down to the tank, cleaning and preparing the area surrounding the existing hole to the best of your ability.
- Attach the tank adapter ring to the tank using stainless steel concrete anchors after applying the butyl sealant tape to the bottom of the ring.
- Install half of the epoxy on the adapter ring and lower the riser so that it rests on top of the epoxy.
- The epoxy and riser are seen in the illustration below.
- Use the provided fasteners to attach the lid, as illustrated below.
Steps that you should follow to install risers on a septic tank
Many American households are projected to consume more than 300 gallons of water each day in their houses, but do you know what happens to the wastewater once it leaves your home? Many people assume that whatever they flush down the toilet will just disappear; but, if you have a septic system, everything will wind up in your septic tank as a result of the flushing.
- Where does this waste water originate from? Toilets, showers, sinks, dishwashers, and washing machines are all potential sources.
It’s critical to understand how your septic system operates and why flushing particles and chemicals down the toilet can have negative consequences. This might result in the need for more regular septic tank services, which no one wants to deal with. As you are undoubtedly aware, a septic tank is extremely essential since it aids in the separation of particles from wastewater, allowing as much of the material as possible to decompose as the liquid runs to the drain field and into the environment.
Installing risers on a septic tank with Blue Diamond pumps makes a lot of sense since they will make pumping, inspection, and maintenance much easier; not to mention the fact that they are required by law in many areas.
1.Get all the necessary parts together
In order to prepare to build a riser system on your septic tank, you will need to purchase a few goods.
These items include a Tuf-Tite tank adapter ring (TAR), a kit for riser adapter rings, butyl rope, Tuf-Tite risers, a Tuf-Tite domed lid or a Tuf-Tite flat lid, and stainless steel screws. The adapter, lid, and risers should all be slightly bigger in diameter than the hole in your septic tank.
2.Make sure the top of the septic tank is clean
One of the most important steps in ensuring that you do a good job of installing risers on your septic tank is to ensure that you create a good seal; this means that you must ensure that the top of your septic tank is perfectly clean so that dirt does not ruin the seal during the installation process.
3.Applying the butyl rope to your tank adapter ring
The butyl rope that you ordered is primarily intended to assist you in achieving a watertight seal on your container. Your butyl rope must be applied carefully and methodically, immediately to the bottom of your Tuf-Tite tank adapter ring, making certain that it is applied completely around your tank adapter ring. Again, getting this correctly ensures a water-tight seal, so take your time and do it perfectly the first time.
4.Putting the adapter ring in place properly
The next stage in the process of placing risers on your septic tank is to ensure that the Tuf-Tite tankadapter ring is correctly secured in place. You’ll want to press the adapter ring onto the septic tank with a little force to ensure that it stays in place. As part of the package that you ordered, you should have a drill bit that will enable you to begin drilling holes in the areas where you see divots on the adapter ring. As soon as the holes are drilled, you may use the tapping screws that included with the package to fasten the adapter ring to the top of your system in the right manner.
5.Apply butyl rope to the risers
In order to make each riser watertight, butyl rope should be wrapped around the recessed rings on the bottom of each one.
6.Place the risers on the adapter ring
The next step is to ensure that the risers are correctly secured to the adapter ring. That’s all there is to it!
What You Should Know About Septic Tank Risers
Septic tank risers are an important part of any septic system, and they should be installed in every property. This article will provide you an overview of septic tank risers and how they may help your septic system. What Is the Function of a Septic Tank Riser? A septic tank riser is a conduit that connects your home’s surface drainage system to your septic tank beneath the ground level. An access port or the pump-out ports on the septic tank are where the riser connects to the tank. Septic tank risers are equipped with lids that can be quickly removed to allow you to check or pump your septic tank without having to dig up your yard.
- These structures are often made of materials that disintegrate slowly over time, such as plastic or concrete.
- What Are the Advantages of Using Risers?
- Normally, this entails digging up your yard before the pump is installed and reburying the tank once it has been installed.
- The use of a septic tank riser can help to minimize the amount of time spent pumping your septic tank.
- The fact that the riser is visible above the surface of your yard makes it an ideal signal for locating your septic tank the first time you need to discover one in your yard.
- For those who want to stay in their house for several years, septic tank risers are not only handy, but they are also cost-effective.
- Concrete risers are more durable, but they are also more expensive, and the price will be determined by the quote you receive from the contractor who will be installing them.
Because labor expenses account for a large amount of the fees that contractors charge for septic system inspection and pumping, installing a riser may possibly reduce the future cost of septic service by as much as 50 percent.
Each and every property can profit from the installation of a septic tank riser, but this does not imply that you should do so immediately.
This allows for the installation of the pump and riser to be completed in a single step.
Because a riser should be considered a long-term investment, you should be certain that your tank is in good functioning shape before installing one.
A septic tank riser is a straightforward concept that may save you a significant amount of money and pain when it comes to septic system maintenance and repair.
We look forward to hearing from you and addressing any concerns you may have concerning your septic system requirements. Contact us now. Please let us know how we may be of assistance to you and your septic system right now!
How to Install Septic Tank Risers
A septic-tank riser is a pipe that goes from a septic tank to the surface in order to raise the tank’s lid. Installation of these low-cost devices eliminates the need to dig in order to reach the tank’s lid for inspection or maintenance purposes, saving you time and money. To place risers on your tank without needing to employ a professional, simply follow these instructions.
Step 1 – Choose the Material
The materials used to make risers include concrete, polyvinyl chloride (PVC), and polyethylene. Concrete is the most common material utilized. The pricing, durability, and convenience of installation of these three materials are all different. Even while concrete is the most inexpensive material, it is also the most difficult to install due to its weight. Risers made of polyethylene are lighter and quicker to install, and they are more resistant to soil erosion than steel risers. They are, however, more susceptible to gas and water leaks than other alternatives.
This material is not only simple to install, but it also does not readily leak water or gas when exposed to extreme temperatures.
Step 2 – Decide Where to Install the Risers
Risers are used to replace the cover of the septic tank and to allow access to the tank closer to the ground’s surface. This access can be constructed above ground, where the risers are clearly visible, or it can be installed close below the surface, where the risers are not visible. Typically, above-ground installation is employed in regions that are neither visible nor interfere with grass maintenance procedures. Installing risers above ground also makes it easier to get to the tank when it is needed.
While this approach makes the risers more inconspicuous, you will have to remove the grass that has grown on top of the risers every time you need to get access to the tank in this manner.
Step 3 – Determine the Height
Septic tanks can be buried as far as three feet below the surface of the ground, although the typical depth is 18 inches, according to the EPA. Risers are available in two different heights: 6 inches and 12 inches. They are built on top of one another until they reach the surface or come to a halt just below the surface of the water. Measure the distance between the tank and the location where the new lid will be put in order to calculate the number of risers that will be required.
Step 4 – Gain Access to the Septic-Tank Lid
In order to install risers, you must first dig down to the septic tank’s lid in order to obtain access to the tank. Allow ample space, roughly 2 feet in all directions, for the installer to be able to move around without being obstructed.
Step 5 – Install an Adapter Ring
Remove the current septic tank cover from its position. Make use of an adapter ring to seal up the entry to the septic system. All of the risers will be attached to this ring at the same time. Concrete is used to hold the ring to the tank in place.
Step 6 – Install the Risers
Install as many risers as necessary to attain the requisite height for an above- or below-ground installation, depending on the situation.
Screwing the risers together will allow them to be connected to one another. The fact that they are screwed together makes them watertight and airtight. It is simple to repair a septic-tank riser if one is ever damaged or destroyed.
Step 7 – Install a New Lid
Lids are available in a variety of sizes. Select a lid based on the size of the risers that you want to use. Installation Instructions: Place it on top of the final riser and fasten it using the two pins that are included.
Septic Tanks Risers- Bring Your Access To Ground Level
Various diameters are available in lids. You should select a lid based on the size of the risers that you want to utilize. Install it on top of the final riser and fix it in place using the two pins that are included with the package.
THE POLYLOK ADVANTAGE
Septic tank risers are available in a variety of shapes, sizes, and designs on the current market. We believe our Polylok septic tank risers are the best money can buy in terms of quality. There are several causes for this, but the following are the most significant:
FACTORY INSTALLED GASKETS
The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.
INTERNAL STRUCTURAL RIBS
Once the hole has been backfilled, the structural ribs in the Polylok septic tank risers are inserted inside around each riser piece, providing them with tremendous strength and allowing them to maintain their shape under the pressure of the earth being pressed on them. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.
LIDS WITH HANDLES
The access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise maintained. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.
LARGE ADAPTER RING
An adapter ring is required in order to properly install septic tank risers on your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!
GET OUT YOUR MEASURING STICK!
An adapter ring is required in order to attach septic tank risers to your septic tank.
You can cover up to a 25″ square aperture or a 27″ circular opening with Polylok’s adapter rings, which are among the biggest available on the market today. Because it accommodates both 20″ and 24″ risers, you have a great deal of choice when it comes to the size of the aperture.
THE COMPLETE RISER SYSTEM
We have a large selection of components from which you may pick to create your own own full riser system. Our many various options offer our product the adaptability to be utilized in virtually any application, but they may also be a bit daunting when attempting to pick which components to buy for a certain application. Each component is discussed in further depth below.
ADAPTER RINGS
The adapter ring is the first component that you’ll need to put together in order to assemble a full riser system. The adapter ring attaches directly to the septic tank, allowing the risers to stack, lock, and mount to it without the need for any additional hardware. Having this component is critical since the risers are not flat on the bottom because they are meant to be stackable, and it is not feasible to install them straight to the septic tank without this piece. The adapter ring provides the flat surface you need to mount to the tank while also being able to accommodate the stackable risers that are included with the tank.
Our square tank adapter ring can accommodate big square apertures up to 25 inches in diameter and large round openings up to 27 inches in diameter.
They are intended to be used with openings that are 24″ or less in diameter.
Concrete anchors, a masonry bit for installing the anchors, and butyl sealer are all included in this set.
RISERS
Following your selection of the adapter ring, it is time to go shopping for risers. The Polylok risers are available in two heights: 6″ and 12″, as well as in two diameters: 24″ and 20″. Stackable, each unit has a gasket that has been fitted as well as stainless steel screws to allow for easy installation. Determine which risers will work best for your application based on the height measurement you made between the septic tank and ground level.
OPTIONAL SAFETY SCREEN
In addition to the 20″ and 24″ riser systems, Polylok also produces safety screens that fit within the riser systems. These screens serve as a supplementary layer of protection in the event that the riser cover is unintentionally damaged or removed, and they keep foreign objects from entering the septic tank. They also keep dogs from slipping into unprotected septic tank openings!
RISER LIDS
You will require a lid to complete your riser system, which is the final component you will require. Both the 20″ and 24″ riser systems may be used with the Polylok lids, which are available in two different types to suit your needs. For ease of access, the basic lid is equipped with handles and a gasket that has been factory placed, as well as stainless steel screws to keep it in place. These lids are strong enough to withstand foot traffic as well as the weight of a riding lawn mower driving across them.
Stainless steel screws are included for installation.
Installations below grade or in regions with a high volume of foot traffic are advised for the heavy-duty lids.
The shipping of these items in large boxes necessitates the addition of additional time, materials, and UPS shipping fees.
SIMPLY ADD THE ITEMS TO YOUR SHOPPING CART AND THEN CHECK YOUR SHIPPING COST. If you place your order before 2 PM CST, you will be able to get your order sent the same day you placed it.
FREQUENTLY ASKED QUESTIONS
The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered!
WILL THE LID FIT DIRECTLY ON THE ADAPTER RING OR DO I NEED TO USE A RISER?
With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength. The height of this reinforcement is actually more than the height of the adapter ring. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter. The lid will not fit through any aperture less than 24 inches in diameter.
CAN I CUT THE RISER SYSTEM DOWN TO A SPECIFIC HEIGHT?
No, the Polylok riser system is available in increments of 6″ and 12″, and it cannot be customized to a certain height. Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.
DO I BRING THE RISER SYSTEM JUST BELOW, AT, OR ABOVE GRADE?
It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade. Because the riser system is airtight and watertight, there is no danger in moving it up to or above grade level.
SHOULD I USE THE STANDARD OR THE HEAVY DUTY LID?
The regular lid is sturdy enough to withstand foot activity and weights up to the weight of a small riding lawn mower passing over it without bending or breaking. If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].
What is a Septic Tank Riser?
- A septic tank riser is normally priced between $200 and $400, not including installation. Risers reduce labor expenses by saving septic contractors time
- Therefore, they lower overall expenditures. The installation of a septic tank riser is not a do-it-yourself activity. Septic tank risers are available in both concrete and plastic construction.
Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. If you’re a homeowner in the United States who relies on a septic tank, you’re probably aware that they’re buried deep in the earth and can be difficult to detect and access when it comes time to do maintenance on them. As a result, you may be required to pay substantial digging and labor fees. With a septic tank riser, you can now find and manage your septic system more rapidly, which will allow you to put more money back in your pocket as a result.
What Is a Septic Tank Riser?
As the name implies, it is a long, robust pipe made of plastic or concrete that connects your septic tank, which is located deep below, with the surface of your lawn. The riser is connected to the septic tank by an access port or a pumping aperture in the tank’s wall. For inspection, maintenance, and pumping, risers have lids that can be opened without digging up your yard. This avoids the need to dig up your yard.
The Benefits: How Septic Risers Save You Money
As a rule of thumb, septic system manufacturers recommend that you examine your septic tank once a year and pump your septic tank every three to five years.
However, if your septic system is not equipped with a riser, you may be forced to pay additional fees.
No Digging Fees
You or your septic tank specialist will have to spend time and money digging through the earth to locate your tank if you or he does not know the precise position of your tank. Your septic tank will need to be recovered with earth once it has been serviced and pumped without a riser, and they will need to do this every time they service your septic tank going forward.
Reduces Labor Costs
If you or your septic tank expert don’t know where your tank is, they’ll have to spend time and money digging through the earth to discover it. Your septic tank will need to be recovered with earth after it has been serviced and pumped, and a fresh hole will need to be dug each time it is serviced in the future.
You’ll Only Pay for Materials and Labor Once
When you have a septic tank riser installed, you will only be responsible for the labor and materials used in the installation. The money you save on yearly inspections and regular local maintenance will more than compensate for the cost of the septic tank riser over time.
Septic Tank Riser Styles
Image courtesy of Ekaterina / Adobe Stock Septic tank risers are available in a variety of concrete and plastic types ranging in size from eight to 24 inches. Each style has its own set of pros and disadvantages.
Concrete Septic Tank Risers
Concrete septic tank risers are more durable than other materials, but they have certain drawbacks of their own. Pros:
- Depending on how well it is maintained and drained, it can endure for 40 years. Septic tank risers made of steel are more durable than those made of plastic. Maintenance is less involved than with plastic
- Installing it is difficult, and purchasing it is expensive. Over time, it becomes more susceptible to corrosion and cracking. Increased labor expenses due to the need to lift and maneuver during installation or inspection
Plastic Septic Tank Risers
Plastic septic tank risers are available in a variety of materials, including PVC and polyethylene, among others. Pros:
- Purchase and installation costs are less expensive than those of concrete. Transport does not necessitate the use of large equipment. When compared to concrete septic tank risers, they are lighter in weight
- They may be covered with sod to improve their looks
- It is not susceptible to cracking like cement. Plastic is resistant to erosion.
- It is possible to crush it beneath the earth
- However, it is not as durable as concrete. Maintenance is more difficult to keep up with than with plastic.
How Much a Septic Tank Riser Costs
It’s possible to smash it beneath the soil surface. Unlike concrete, it is less durable. When compared to plastic, wood requires more upkeep.
Installation Usually Requires a Plumber
In part due to the difficulty of septic tank installation, it is not recommended as a Do It Yourself job. While it is possible to purchase all of the supplies for a DIY installation on the internet, there are several safety dangers associated with doing so. Opening a septic tank access can result in the emission of poisonous fumes, which can cause someone to go unconscious. Additionally, without prior experience, waterproofing and ensuring that the risers are properly connected together might be difficult.
They’ll dig up the area surrounding the access hole, then fill up the dirt around the pipe and install a cap on the upper section of the riser to make it easier to get to the pipe in the future.
Tired of Digging Up Your Septic Tank Lid? Install a Riser. – Advanced Septic Services Inc
- Home
- Blog
- Are you tired of digging up your septic tank lid every time it rains? Install a stair riser.
December292017InBlog Depending on where they are located in the ground, septic tanks can be anywhere from a few inches to several feet below the surface of the earth, necessitating the excavation of the septic tank lid every time it has to be repaired. Hand digging can be tiresome and back-breaking job, and it is something that many people prefer to avoid at all costs. The avoidance of digging frequently results in a septic system that has been neglected, and in severe cases, has failed. Many homeowners are not aware of the potential improvements that may be done to their septic tank in order to avoid the need to excavate entirely from their property.
What exactly is a riser?
In many circumstances, the installation is rapid, simple, and reasonably priced.
We usually replace the old concrete lid with a green, plastic cover that is affixed to the riser pipe itself, rather than the riser pipe itself.
A septic tank preventer may save you time, effort, and money in the long run.
Make contact with our staff at Advanced Septic Services by calling (717) 789 – 4548 or using our online form to schedule your riser installation. CMR Designs retains ownership of the copyright. All intellectual property rights are retained.
