How To Fix Septic Tank Baffle?

  • If the baffle has been damaged, knocked off or has rusted out, it must be replaced or repaired. A plumber can knock off a baffle by using a drain router to unclog a pipe. The router strikes the baffle and it falls into the septic tank without anyone knowing it until a problem develops.

Can you repair a septic tank baffle?

If the baffle becomes damaged or is forced out of place, it would be impossible to repair. This is because repairing it would effectively mean digging the septic tank out of the ground and attempting to break it in to two halves again!

How much does it cost to fix a septic tank baffle?

Repairing a baffle costs $300 to $900 on average. You may pay more if it’s tough to access. The baffle helps to prevent buildup in the incoming or outgoing pipes of the tank.

How long does a septic baffle last?

Inspectapedia estimates that a steel tank baffles will rust out in 15 to 20 years and may collapse if driven over, but a concrete tank will last 40 years or more as long as the wastewater is not acidic. It’s important to consider the life expectancy of a drain-field, too.

Do all septic tanks have baffles?

Every septic tank contains two baffles, one at the inlet and one at the outlet.

How does a baffle tee work?

The baffle is inside the tee and it directs the water, that is being ejected from the disposal with force, downward. With out the baffle the pressure is to great and the water will shoot the wrong way. In the photo below the water comes from the disposal on the right, the baffle is in the tee.

What is the average life of a septic system?

Age of the System It’s pretty common for a septic system to last 40 years or longer, which means if you buy a new home, you might never need to replace it. However, you might have an older home whose septic system has been in place for nearly half a century.

How much does it cost to replace lateral lines?

FULL REPLACEMENT If you need to get part of the lateral replaced, you will pay between $50 and $200 per linear foot. If you need to get a small piece of the sewer lateral replaced, that will be between $3,000 and $6,000. For sections longer than 50 feet, the cost will be between $5,000 and $13,000.

Why does my septic filter keep clogging?

A properly working septic tank outlet filter will become clogged as effluent is filtered and leaves the septic tank. As the solid materials accumulate over time, they progressively clog more and more of the filter, requiring maintenance. They should also be cleaned when you get the tank pumped and cleaned.

How do you know if your lateral line is clogged?

Stay vigilant for five signs your drainfield does not drain correctly anymore.

  1. Slowing Drainage. Homeowners first notice slower than usual drainage from all the sinks, tubs, and toilets in a home when they have a compromised drainfield.
  2. Rising Water.
  3. Increasing Plant Growth.
  4. Returning Flow.
  5. Developing Odors.

Why does my septic tank keep getting clogged?

A clogged septic tank or drain is caused by a number of things: An obstruction in the line caused by a buildup of pressure between the object and the inner circumference of the pipe. An example is a diaper stuck in the sewer drain line. There is simply too much diaper to fit through the line at once!

Why do septic tanks have baffles?

The inlet baffle directs the flow of wastewater into your septic tank, and prevents the scum layer in the tank from being disturbed. It also can help prevent solids from backing up toward the house if you should experience a septic system backup.

Where is the baffle located on a septic tank?

Septic baffles are located at the junctions where pipes enter and exit the tank. The one at the inlet pipe is called the inlet baffle, and the one at the outlet is called the outlet baffle.

Expert Tips for Baffle Repair

Receive articles, stories, and videos about repair sent directly to your email! Now is the time to sign up. Repair+ Receive Notifications One perk of working on septic systems for more than 40 years is that the folks I’ve met and worked with are frequently willing to offer images or tales that they find interesting. In this particular instance, my colleague Kim Seipp emailed me a photo of a repair work she had completed in Colorado. Hopefully, everyone who reads this recognizes right away that this is not the appropriate method of repairing or replacing a baffle in a concrete tank.

These baffles must be the right length and have a space between their top and the bottom of the tank lid to allow for the exchange of gases and the ventilation of the tank.

Thus, sewage travels through the tank on an irregular course, providing the detention time necessary for bigger particles to be settled out before the effluent is transferred to the final treatment and dispersion section of the system.

A floating scum blockage is prevented by the intake baffle from clogging the inlet pipe.

  1. It is necessary to maintain floating scum in the tank, which is composed of oil and soap residue, so that it can be removed when the tank is cleaned.
  2. A deteriorating concrete baffle at the exit of a septic tank is seen in this photograph.
  3. Due to the fact that the sanitary tee is connected to the tank’s output pipe by couplings, the person(s) who completed this project had the appropriate concept.
  4. This baffle will not perform the critical job of providing a relatively clear liquid to the next component of the system since there is no effluent filter in place.
  5. The concrete around the pipe may require repair, and a rubber gasket may need to be installed retroactively to guarantee that the tank stays watertight and root-free.
  6. The outlet baffle should be extended to a depth of 25 percent of the operating depth in the tank to ensure proper operation.

As an example, if the tank is 60 inches deep, the baffle would need to be 15 inches longer. I’d be interested in hearing how others might go about mending a baffle in the future. Leave a comment below or send an email to kim.[email protected] with your baffle repair suggestions.

How to Replace a Septic Tank Baffle

In the event if your septic tank is kept in good condition by frequent plumping, a septic tank baffle is not necessarily essential. Even if there isn’t one, the tank is perfectly functioning. Providing that it is well maintained, with regular pumping, or that there are no other difficulties that might cause a large amount of sludge to accumulate in your tank, this should be possible for you. For example, if your tank has to be pumped out once every 4 or 5 years, or if the wastes are discharged into a drain field, you should consider installing a filter on the outlet side of the tank.

If the baffle on your tank has been rusted or broken, you may replace it rather than having to purchase a completely new tank.

Step 1 – Accessing the Septic Tank

You should get access to the exterior of the septic tank, which is where the water is discharged into the drain field. If you are unable to reach the lid from the ground level, you will need to dig to gain access to the lid.

Step 2 – Clean the Area

If there is a tank leak, you should contact the local health department to find out what you need do to clean up the area around the leaking tank.

Step 3 – Pump the Tank

If there are any issues, you should pump the tank in order to ease the difficulties that are now present. If you want to replace the baffle or possibly the entire septic tank, this is a very crucial step. Step 4 – Unlock the outlet side of the device. Once you’ve opened the lid on the outlet side, you should be able to reach the top of the baffle and slide the new filter or new baffle down until you reach the handle of the filter, as shown in the picture. The access plate should be elevated above ground level if digging was required in order to reach it.

Extra Tips

You should keep in mind that, while filters can solve many issues, they can also cause many new ones. So be cautious while using filters. If you are the system owner and you perform the work on your own, you are aware that the system and filter must be properly maintained in order to avoid clogging and other problems. Solid waste depositions in the drain field are caused by clogging of the drain. According to other reports, the technology may even back them up inside the house. It is possible to extend the life of a septic tank and system by reducing the quantity of water that enters the particular system.

If you keep track of how much water you use, you may save money on water and avoid having to make costly repairs to your septic tank.

How to Replace an Outlet Baffle in an Existing Septic Tank

The baffles in your septic tank are critical to the proper operation of the tank. If the baffles in the tank are not working properly, the sludge floating in the tank might enter the field lines or back up into the home drainage system.

It is possible for baffles to rust, crack, or otherwise degrade over time. Every time the tank is emptied out, it is important to inspect the baffles to ensure that they are in excellent working order.

Step 1

Find the location of the septic tank. Most contemporary tanks feature two access doors, one on each end of the tank, which makes for easier maintenance. Excavate to the top of the septic tank and remove enough dirt to expose both access hatches and provide you with enough space to operate comfortably and safely. Check to see that you will not be dumping dirt into the tank while you are working.

Step 2

Make sure you open both hatches and get a professional to pump out the septic tank. A licensed specialist is equipped with the necessary equipment to correctly pump out waste materials and dispose of them in a safe and legal manner, as well. It is not recommended that you enter the septic tank or allow anybody else to enter the tank. The gases are poisonous, and the absence of oxygen can induce asphyxia in a short period of time.

Step 3

Make sure to open both hatches and call a professional to pump out your septic tank. In order to effectively pump out waste materials and dispose of them in a safe and legal manner, it is necessary to hire a qualified specialist. If you enter the septic tank or enable anybody else to enter the tank, you should be in trouble. In addition to being hazardous, the absence of oxygen can result in asphyxia within minutes.

Step 4

Check that all of the fittings and connections are securely and firmly in place before proceeding. Check to see that the seal around the pipe where it enters the septic tank is secure to ensure that there is no leaking. For effective liquid flow management into the field line, the baffle on the outlet end of the septic tank should be 4 to 6 inches longer than the baffle on the input end. According to the manufacturer, the 24-inch portion of pipe that was installed should be more than enough to satisfy this requirement.

Step 5

In order to ensure that they are firmly in place, replace the access hatches and back-fill the hole with a suitable material. It is important to check on the new baffles the next time the tank is emptied out to ensure that they are still in place and in excellent shape.

Can you repair a septic tank baffle

Furthermore, this is only applicable if your septic tank empties to a soakaway system. As previously stated, the aim of a septic tank baffle is to keep solid waste contained within the tank while enabling waste water to escape via the tank’s opening. Afterward, the waste flows via a soakaway system, which is typically comprised of a network of perforated or slotted pipes that allow the waste to safely percolate through the sub soils. So, what does any of this have to do with septic tank baffle repair, I hear you wonder?

This is due to the fact that if the baffle is not functioning properly, solid waste might escape from the tank and into the soakaway system.

As a result, the soakaway often becomes blocked.

As a result, even if a septic tank baffle repair were possible, it is more than likely that it would not resolve the drainage issues you are experiencing.

Even if the septic tank was able to be repaired, the soakaway would have been rendered useless. Instead of the waste water being able to filter into the surrounding soil, it will be unable to do so and will simply flow back to the tank or rise above ground.


By Admin on November 12, 2020 Your efforts to live as environmentally conscious as possible, as a responsible homeowner, are likely already underway, with practices such as recycling, composting, and purchasing energy-efficient equipment among your list of accomplishments. As a septic tank owner, you want to be sure that anything you put into your tank and septic field is causing the least amount of ground contamination as is reasonably practicable. Fortunately, there are a number of modest improvements you can do immediately to make your septic system even more ecologically friendly than it already is.

  • Have your septic tank inspected and pumped on a regular basis.
  • A bigger septic tank with only a couple of people living in your house, for example, will not require pumping as frequently as a smaller septic tank or as a septic tank that must manage the waste products of multiple family members will require.
  • When in doubt about how often to pump your septic tank, consult with a professional for advice.
  • In addition to locating and repairing any damage, a professional can ensure that the septic field is in good working order and that your septic tank is functional, large enough to handle your family’s waste, and not causing any unwanted pollution in nearby ground water.
  • Avoid flushing non-biodegradable items down the toilet or down the toilet.
  • Items that are not biodegradable are unable to properly decompose in the septic tank and might cause the system to get clogged.
  • In addition to causing issues in your house, septic system backups can damage ground water in the area surrounding your septic field.
See also:  How To Clean The Trap That Leads To The Septic Tank? (Solution)

Towels made of paper Products for feminine hygiene Grease or fats are used in cooking.

grinds from a cup of coffee Even if you have a trash disposal, the food scraps that you flush down the drain and bring into your septic system may cause unanticipated harm to your plumbing system.

Food scraps can enhance the amounts of nitrogen and phosphorus in the wastewater, which can disturb the natural bacterial balance of the septic tank, among other things.

Water conservation should be practiced.

Exceedingly large amounts of water use will interfere with the normal flow of wastewater from your home into your septic tank.

Limiting the amount of time you spend in the shower and turning off the faucet while brushing your teeth, as well as purchasing a smaller dishwasher and washing machine that use less water, are all simple strategies to reduce water use in your home.

The following are some basic steps you can take to make your septic system more ecologically friendly: save water, maintain your septic system and tank, and recycle wastewater. To get answers to any of your septic tank-related issues, get in touch with the experts at Upstate Septic Tank, LLC.

Preventive Maintenance: Baffle Replacement Becomes Legitimate…

This intake baffle will be unsuccessful at directing flow downward for efficient settling because it will not direct flow downward.

Interested in Onsite Systems?

Efforts to divert flow downhill for efficient settling will be futile with this input barrier installed.


The exit baffle prevents floating scum or debris from entering the drainfield and guarantees that the effluent that is discharged to the next component of the system comes from the tank’s clean effluent zone, which is important for water quality. In today’s world, we improve debris removal by utilizing effluent screens to prevent big floating particles from entering the downstream flow. My response to the question is as follows: If the baffle is degrading and the degradation is preventing the baffle from performing its intended function, the baffle should be changed immediately.

  • In this column, I will provide a suggestion for the second half, which is easier than convincing the homeowner that they need expensive repair done on their system, which is more difficult.
  • As previously stated, many licensing agencies need effluent screens when a tank is rebuilt or repaired, as noted above.
  • Salespeople should have little trouble convincing homeowners that an effluent screen is a type of insurance policy that would cover the more expensive components of their system.
  • Thanks to Jeff and Kim Seipp of High Plains Sanitation in Colorado for providing the photo of the outlet baffle that was used in this article.
  • Other photos, including one from Arizona, were taken as part of a point-of-sale real estate inspection and have been shared with us.


When the exit baffle is in place, it prevents floating scum or debris from entering the drainfield, as well as ensuring that the effluent that is discharged to the drainfield is from the tank’s clear effluent zone. These days, we improve debris removal by utilizing effluent screens to prevent big floating particles from going through the system and into the environment. Therefore, my response to the question is as follows: If the baffle is degrading and this degradation is preventing the baffle from performing its intended function, the baffle should be replaced.

  1. In this column, I will provide a suggestion for the second element, which is easier than convincing the homeowner that they need expensive repair done on their system, because it is subjective.
  2. If the tank is changed or repaired, as previously stated, many permitting agencies may need effluent filters.
  3. It should be reasonably simple to persuade the homeowner that an effluent screen is a form of insurance that will safeguard the more expensive components of their system.
  4. Thanks to Jeff and Kim Seipp of High Plains Sanitation in Colorado for providing the photo of the outlet baffle that I used in this article.

Tank conditions and corrosion-related factors have been the subject of an ongoing debate. Other photos, including one from Arizona, were taken as part of a real estate inspection at the point of sale.

Maine Septic and Pumping – Lewiston Maine

A baffle is located at the inflow and exit of a septic tank. Typically, these baffles are formed of concrete and are included into the tank’s overall design. When the intake baffle is in place, the flow of liquid entering the tank is slowed down, and turbulence is reduced, enabling particles to settle to the bottom of the tank. Using the outlet baffle, you may aid to keep solids in the tank and prevent them from exiting the tank and making their way to your absorption area. A tank that does not have an output baffle might reduce the longetivity of your septic system and lead it to collapse sooner than expected.

What Happens Without an Outlet Baffle?

An input baffle and an output baffle are both present in a sewage treatment system. They are typically formed of concrete, and they form an integral aspect of the tank’s design. When the intake baffle is in place, the flow of liquid entering the tank is slowed down, and turbulence is reduced, enabling particles to settle to the tank’s bottom. Using the outlet baffle, you may aid to keep solids in the tank and keep them from exiting the tank and making their way to your absorption region. A tank that does not have an exit baffle might shorten the life of your septic system and cause it to collapse sooner than expected.

Simple Procedure to Replace!

Using a new plastic sanitary tee, Maine SepticPumping may repair your outlet baffle and restore proper operation to your system. The replacement will aid in the retention of solids and will assist to restore protection to the absorption region.

Residential Baffle Repairs & Installation

The baffles in your septic system are one of the most significant components because they prevent sediments in your septic tank from escaping into the drain field. If sediments make their way into the drain field, they may cause the drain field to clog, which may result in the collapse of the entire system. Our highly skilled professionals evaluate your inlet and outlet baffles as part of our complimentary 10-point inspection to ensure that they are in perfect functioning order. River Valley Septic is the company to call if you reside in Bucks, Northampton, or Hunterdon County and have a baffle that needs to be fixed or replaced.

The presence of broken or missing baffles can result in significant difficulties, and they should be changed as soon as possible to maintain effective operation of your septic system and to prevent big issues from arising in the future.

Call today for a free estimate!

You have the problems and we have the fixes, call now!

The septic tank baffle tee (also known as a baffle) is a device that may be found at either the inlet or exit of your septic tank. It is made of plastic and has a hole in the center. The goal of these devices is to prevent sewage from entering into pipelines. There are two types of septic tank baffles: inlet baffles and exit baffles, which are called after the locations in your septic tank where they are installed. In both cases, the idea is to simply channel waste water around your septic tank while also removing the particles from the wastewater.

Its goal is to aid in the effective flow of wastewater into your tank while avoiding disruption of the scum layer.

As previously stated, the outlet baffle is extremely significant since it is responsible for preventing sediments from entering your septic tank and reaching the leach field.

Because of the nature of the task that baffles do for your septic system, they become worn down over time and eventually decline in performance.

You may receive a free estimate from your friends at One Way Septic to get started, and you can learn more about this critical septic system component by continuing to read below.

Signs Your Baffle Tee Needs to Be Replaced

Clearly, baffles are a crucial component of your home’s septic system, and there are a few signs that they may need to be replaced that you should be aware of.

  • Clearly, baffles are a vital component of your home’s septic system, and there are a few signs that they may need to be replaced that you can look out for.

To be sure, if you’re unclear about whether or not your baffle tee needs to be changed, give us a call and we’ll arrange an examination for you!

Why Partner With Our Local Septic Company?

Assistance is available 24 hours a day, seven days a week. A total of more than 30 years of combined experience Response Times That Are Incredibly Quick Services that are centered on the customer

When Should I Replace My Baffle Tee?

It is possible that the reasons for when one should replace theirs will differ from tank to tank because they are different. Generally speaking, the answer is straightforward: if the baffle has been broken or is progressively decaying, it’s generally a good idea to replace it. In the end, that degeneration will be the factor that prohibits it from accomplishing its goals and objectives. You should replace your baffles regardless of whether or not you’ve observed a drop in overall performance.

Preventative maintenance is always the best course of action to take in order to avoid encountering worse problems in the future, as previously stated.

Work With an Experienced Septic Company in Acworth

Whether you’re looking to perform preventative maintenance on your system or have a baffle tee that’s in desperate need of replacement, One Way Septic is proud to offer a wide range of septic services, including emergency septic services, to residents and business owners in the greater Philadelphia area. Throughout our service region, from Lawrenceville to Stone Mountain and beyond, you will find our professionals ready to meet your requirements. Get in touch with us right away!

Get In Touch With One Way Septic

If you are facing a septic emergency, we offer the finest answer for the situation you are experiencing. Contact us now. Don’t just sit around and expect that the problem will go away on its own. Give your friends at One Way Septic a call instead if you require immediate help. Our professional specialists are here to assist you 24 hours a day, seven days a week, regardless of whether your problem is residential or commercial in nature. We guarantee that we will come to your call as fast as possible, and that we will be prepared with all of the essential equipment, tools, and tried-and-true procedures to ensure that your emergency service is as quick, efficient, and stress-free as it possibly can be.

You can also phone us right now at (404) 775-1164 for quick assistance.

Get in Touch With Us Immediately

Old Septic System Baffle Repair

Over 680,000 strictly plumbing related postsWelcome to the We are the best online (strictly) PLUMBING advice, help, dyi, educational, and informational plumbing forum. Questions and discussions about toilets, sinks, faucets, drainage, venting, water heating, showers, pumps, water quality, and other exclusively PLUMBING related issues.Please refrain from asking or discussing legal questions, pricing, where to purchase a product, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing.Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups. We do not sell your information. We are made possible by:
Old Septic System Baffle Repair
Author:mstruttm (FL)Just had my very old septic system inspected and pumped. Turns out the concrete baffles have rotten and fallen into the tank. It’s not really feasible to use PVC tees as new baffles because the tank is so old that it has two clay outlet pipes. I was thinking about building some baffles out of stainless steel similar to the old concrete baffles and fastening them with tapcons to the septic walls. Is this a good idea?The outlet baffle looked like this _/ if you were looking from the top down into the septic tank, with the outlet pipe in between the opening. It probably went down about two feet. The inlet baffle seemed to just be a wall that went from one side of the tank to the other, but I’m not sure how far it went down.Edited 1 times.
Post Reply
Re: Old Septic System Baffle Repair
Author:Dunbar (KY)Those baffles go to the bottom, and are designed as such to allow the first bay to take on most of the solids, second bay to settle waterborn particulates, third bay to be the finished “clear” effluent that safely distrubutes to the finger system of leaching fields.I haven’t seen John Aldrich “Septic Tank Yank” here in a long time. Anyone know of his whereabouts?His last post was around 318,000 and we’re at 383,000 on this thread.Right about the time I stopped getting emails from him. I hope all is well.-Always be aware of cross-connections in your potable water systems-They could one day harm you and your loved ones.Edited 2 times.
Post Reply
Re: Old Septic System Baffle Repair
Author:PBwrencher (WI)Tank Yank would be the best source for this question however; from my limited experience this person is looking at replacing that old thing, you could image what the rest it of looks like, it’s lived it’s life and now a new one is needed.10-22-08, 8:18am- – – – – – – – – – – – – – – – – – – -3 years before Google started has been THE best plumbing supplier on the web. Please visit our sponsor
Post Reply
Re: Old Septic System Baffle Repair
Author:hj (AZ)The outlet baffle is to prevent grease, etc., on top of the water from exiting through the outlet. The inlet baffle goes down to a point a foor or so above the floor to give the influent time to separate.
Post Reply
Re: Old Septic System Baffle Repair
Author:mstruttm (FL)I understand that the system is very old and will need replacing, but it is still functioning and I would like to get as much life out of it as possible. Now isn’t the best time to be forking out $5,000-$10,000.After the tank was pumped, I could see the outlet baffle at the bottom of the tank and it definately was not long enough to go all the way to the bottom. The pump guy said it only runs down a couple of feet. He told me I shouldn’t really be concerned with the inlet baffle and it was the outlet baffle that was important. I’m just thinking something will be better than nothing so I can get some more life out of the system.
Post Reply
Re: Old Septic System Baffle Repair
Author:dlh (TX)this isnt a car. i have never heard of anyone repairing a septic tank.i have found it is much better to bite the bullet now than it is to wait. waiting almost always means a larger bill in the end.-PLUMBERS “Protecting The Health Of The Nation”
Post Reply
Re: Old Septic System Baffle Repair
Author:yonson (SC)My septic guy told me the same thing when my exit collapsed (the exit is most important). He placed a “t” type port at the exit, but mine was PVC. An easy fix.
Post Reply
Re: Old Septic System Baffle Repair
Author:LemonPlumber (FL)Do you have a scrap or 12″ diameter pvc pipe,two feet long?cut it in half use half at each end tapcon it with the top, at the top of the inlet hole and the outlet four inches or so higher than that.Old culvert pipe.Dead propane cylinder.If you use metal it may decay faster but should give you five years to save up.Good Luck with any rig.You need a new tank.
Post Reply
Re: Old Septic System Baffle Repair
Author:mstruttm (FL)Ok, I know the tank needs replacing, but it’s not going to hurt by rigging it to last a little longer since the entire system will need to be replaced anyway. I am not doing any more damage by not replacing it now.So, the 12″ PVC sounds like the best idea yet.
Post Reply
Re: Old Septic System Baffle Repair
Author:PBwrencher (WI)”There is nothing so permanent then something so temporary.”The plumber I served my apprenticeship under would say that when we were called in to make the correct repair after a handyman or homeowner only did a temporary fix that would last sometimes for years.Be honest, it will never get fixed until the system completely craps out.10-23-08, 7:18am- – – – – – – – – – – – – – – – – – – -3 years before Google started has been THE best plumbing supplier on the web. Please visit our sponsor
Post Reply
Re: Old Septic System Baffle Repair
Author:yonson (SC)”it will never get fixed until the system completely craps out”Pun intended?
Post Reply
Re: Old Septic System Baffle Repair
Author:mstruttm (FL)I also plan on constructing new concrete lids. Is this ok to do with quickrete conrete mix and rebar? I want to make sure that there is no danger of the lids breaking, which there is with the current lids.
Post Reply
Re: Old Septic System Baffle Repair
Author:hi (TX)Hello,You may still be helped.The exit T and the baffle are placed to keep solids and greases out of the leach field which will plug the pores and render the leach field inoperative and result in effluent finding its way to the surface.You have a two chamber tank that has made itself a one chamber tank with the collapse of the baffle wall.This is not an infrequent finding during septic inspections done properly.Your best (most effective and cost effective)fix is to place a PVC Tee on the outlet to the box.This keeps the floating solids out of the field.It needs to be fit solidly and leak free to be effective and long lasting.If possible also place an inlet T to force “incoming” waste to go to the bottom rather than float across to the exit of the tank.If the repair exposes the exit of the tank you may also want to include an effluent filter to trap solids before they go to the field. This is a newer design that further reduces material that can plug up the leach field.Be careful with the tanks as they can collapse and may not have enough oxygen to support life inside!Safety is Most important!Here is a article discussing your exact question. The website contains a “wealth” of septic info.Here is another (scroll about 3/4 way down and see the part about the baffle deterioration and repair.)
Post Reply
Re: Old Septic System Baffle Repair
Author:mstruttm (FL)I mentioned in my first post that using tees is not feasible at the outlet due to there being two clay outlet pipes. I guess I could try to use two tees, but how would I secure them to the clay pipes?
Post Reply
Re: Old Septic System Baffle Repair
Author:LemonPlumber (FL)You might be better off wrapping the old ones,with rewire making the joint on top then adding a 2″ layer of topping mix.Good Luck.Unless you intend to pour the lid’s six or more inches thick,smaller stone or sand type should be used.
Post Reply
Re: Old Septic System Baffle Repair
Author:PBwrencher (WI)Don’t you have plumbing codes in Florida where the concrete tank and top must be made of Monolithic Concrete and must have the strength of 2000lbs per sq inch or more so it does not cave in on a poor sole years from now:10-25-08, 8:20am- – – – – – – – – – – – – – – – – – – -3 years before Google started has been THE best plumbing supplier on the web. Please visit our sponsor
Post Reply
Re: Old Septic System Baffle Repair
Author:redwood (CT)Things are a tad bit lax in Florida IMHO- – – – – – – – – – – – – – – – – – – -Since 1995 (3 years before Google started) has been THE best plumbing supplier on the web. Please visit our sponsor
Post Reply
Re: Old Septic System Baffle Repair
Author:mstruttm (FL)Quickrete says it is 4000 psi.
Post Reply
Re: Old Septic System Baffle Repair
Author:rca411 (OK)Can’t you just dig it up some behind the tank, then stub PVC back into the septic tank and glue on a sanitary tee for a new baffle?
Post Reply
  • Messages that are inappropriate or that are obvious advertisements will be removed. Unfortunately, we cannot be held liable for incorrect or insufficient advise
  • Furthermore, has no control over external content that may be linked to from messages placed on this site. Please use caution when clicking on external links
  • is strictly for the exchange of plumbing-related advice and NOT for questions about pricing or costs, where to find a product (try Google), how to operate or promote a business, or questions about ethics (law) and the like
  • is also not a place to ask questions about radiant heating (try, electrical, or even general construction type questions
  • is strictly for the exchange of plumbing-related advice and NOT We are only here to answer plumbing-related questions.
Search for plumbing parts on our sponsor’s site:

Special thanks to our sponsor:

Baffle, Repair Replace

Repair and baffle Replace niftyadmin2022-02-01T19:28:43+00:00 Make an appointment for a free on-site quote now! When it comes to septic systems, the septic baffle is the most crucial component. When the input baffle is closed, wastewater from the sewage line is forced to settle at the bottom of the tank rather than flowing over the surface and into the outlet pipe that leads to the absorption zone. A device installed on the outlet of a septic tank that deflects gas and bubbles away from the outlet while also reducing the amount of solid particles carried over from the septic tank via the outlet.

A flow deflecting device that is used in septic tanks and distribution boxes to prevent the discharge of floating materials, lower the quantity of settleable solids that escape, and reduce the exit velocity of the wastewater are all examples of settling devices.

We provide essential maintenance to all customers!

We feel it is critical to support organizations and businesses who are striving to make a good difference in our industry and community at large. We take great satisfaction in growing as a company by utilizing the greatest products, from reliable vendors, and ethical business procedures in order to provide superior service to our customers. It would not be feasible to deliver the Honest and Ethical Service that we do without the support of our industry partners and the client relationships that we have built across Southern Idaho since 1948.

a link to the page’s load

Our Services

Our pump truck is waiting for you, fully stocked and ready to get to work for you right away. Having cutting-edge equipment that can get the job done when others are struggling is something we take great pleasure in.

RV Pumping

If you have a recreational vehicle and are unable to move it, we can provide pumping services for your vehicle. To prevent your waste tank from being sucked flat during the operation, a specific connection must be used. Our vehicles are well equipped and prepared for the job.

Inspection Camera Work

If you are concerned about a possible problem and would want to get a better look at it before investing a lot of time and money on it, you may want to consider employing our camera equipment to get a better look at it. Before you start digging, make sure you’re making the appropriate choice.

Baffle Replacement

Septic tanks are nothing more than enormous solids-collection containers. Baffles are a component of a septic tank that helps to keep sediments contained. When baffles are missing, incorrectly fitted, or degraded after years of exposure to hydrogen sulfide gas, which is found in all septic tanks, it is recommended that they be removed and replaced.

Filter Installation

Having a filter put on the outflow of your sewer system is another method of keeping sediments contained in your septic tank. Filters like this are reusable and simple to clean. By keeping tiny solid particles from leaking into your pump chamber or drain field, you may extend the life of your septic system by many years or more.

Riser Installation

The use of rippers is mandatory on all new septic systems, and they may be retrofitted to older septic systems as well. Risers are devices that raise the lids of septic tanks to the surface of the ground. Inspections, maintenance, and pumping access will be much easier as a result of this. There aren’t many firms nowadays that will find and dig for free. The money you would have spent on excavating and finding will be used to pay for your riser installation over the course of time. Not to add the time saved if you have a backup tank and need to get to the tank quickly when you don’t have one.

Submersible Pump Replacement

Septic systems are growing more sophisticated than they have ever been before. In many septic systems, one or more submersible pumps are included as part of the overall system. The pumps in question are electromechanical devices.

They require the services of a service specialist to properly connect them to the water supply and set the floats in accordance with the design specifications. The electrical work is next required to be completed by a licensed electrician in the labor business.

Drain Field Installation / Repair

More and more complicated septic systems are being installed. Septic systems frequently use one or more submersible pumps as integral components. This type of pump is made of electro-mechanical components and components. They require the services of a service specialist to properly connect them to the water supply and set the floats in accordance with the specifications of the building. The electrical work is then required to be completed by a licensed electrician, as required by the labor industry.


We are completely competent of doing inspections for a variety of clients.

  • Home sale
  • County health department approval required
  • Septic system certifications required

Septic System Certifications Required; Home Sale; County Health Department Required;

  • Home Sale
  • County Health Department Requirement
  • Septic System Certifications

For all of your unsolved issues, symptoms, and problems related to your septic system, we can provide system troubleshooting and guidance. When you have a problem with your septic system, let our years of knowledge guide you to the most cost-effective solutions.

Preferred Customer Program

Superior is assisting you in lessening the impact of growing septic system maintenance expenses on your pocketbook. I am pleased to offer you this tool, which allows you to set money aside in a trust account for the sake of system maintenance. Call and ask for further information at 425-905-2485.

Tank Locating

We can locate almost any tank using the most up-to-date electronic devices. Simply flush a transmitter and follow it to the tank to complete the process.

Main Line Cleaning (jetting)

Using soap and disposing of grease from clothing and dishes add to the accumulation of sediment in the main line leading to the septic tank, which can cause it to back up and overflow. This buildup will cause drainage to become sluggish and eventually back up into the residence. Every six years, it is suggested that you have your line cleaned. Line cleaning equipment with a high volume and pressure scours the line like new and then draws the loosening material back to the tank using our high volume and pressure equipment.

It is recommended that the line be cleaned every other time if your septic system is on a three-year inspection and pumping plan.

Trap Clear

There are a variety of solutions available to keep your lines clean these days, but Trap Clear is one that is particularly well-known in our field. It is not available for purchase over the counter, and it is only available for purchase via industry specialists.

Rapid Baffle Repairs For Titusville Septic Systems

These days, there are a plethora of treatments available to keep your lines clean, but Trap Clear is one that is particularly well-known in the business. Aside from industry specialists, it is not available for purchase over-the-counter.

What Are Your BafflesWhat All Do They Do?

A total of many baffles are installed on each septic tank, and both types serve an important function. Your baffles are responsible for ensuring that no backflow into your home occurs, so keeping the interior of your home safe. They are located on one end of the tank. Your baffles, on the other hand, are intended to aid in the prevention of backflow into your drainage field.

In the event that any of these baffles is damaged or has fallen into disrepair, it can result in a variety of problems that can only be resolved by expert repairs performed by an experienced septic service company.

How Do You Fix Your Baffles?

Baffle repairs are performed in a variety of ways, one of the most popular being the installation of a septic tee in places where an original baffle has been damaged or lost. Unblocking the tank is made possible by the use of an inexpensive plastic pipe that can be attached to either side of the tank to restore functioning. In and of itself, the pipe tee isn’t very expensive, but depending on how much of the tank needs to be repaired as well as how much excavation is required, the expense of baffle repairs can become prohibitively expensive.

Our latest projects

  • How to Keep Your Home Safe by Taking Good Care of Your Septic System Your Titusville home is more than simply a place for you and your family to live
  • It is also a secure haven where memories are built, meals are shared, and a variety of other activities take place. Moreover, it’s one of your most crucial investments. How to Prepare for the Installation of a Septic Tank The process of installing a new septic tank system on your property is time-consuming and labor-intensive. There’s no getting around it, and it’s a procedure that should be handled seriously and completed by an industry specialist in order to achieve the best results possible.

Call your expert titusville septic company today!

A septic tank is an extremely important component of any property. You can’t take the chance of getting into the unhealthful and maybe deadly condition that comes with it breaking down. However, it is impossible to ignore the reality that the tank would eventually get contaminated. What should you do if anything like this happens? Several factors might contribute to the failure of the baffle on a sewer tank, including a leak in the tank, a blockage within the tank or even a design flaw during the building process.

Some of these components may include the drainpipe, the baffle, or the tank’s lid, among others.

As a result, you must ensure that any breakages are repaired as soon as possible.

The baffle is the subject of this blog.

What really is the septic tank baffle?

Not everyone who owns a septic tank is likely to be familiar with all of the components of the tank and their respective roles. Some people may only be familiar with these areas if they have called a plumber to address a problem. One downside of this approach is that you may wind up spending more for repairs because you have no clue how much the plumber will charge you in the first place. It is completely natural if you be unaware of these details. Nonetheless, you may need to be familiar with what an aseptic tank baffleis and what it accomplishes in the tank in order to properly operate it.

The intake baffle directs the material from the house’s sewage system directly into the tank’s collection system.

The outlet baffle, on the other hand, is responsible for dealing with the material that is expelled.

How to know if a septic tank baffle needs replacement

When looking for a spoiled baffle, it might be difficult to tell the difference unless you are very attentive. In other words, when do you know for certain that the baffle will need to be replaced? For starters, the baffles in older tanks are often made of concrete that has been put in place. Those in new tanks are sanitary tees, which enable for a sewage screen to be installed at the exit of the tank. As a result, if the baffle’s condition has deteriorated to the point that it is no longer effective, it must be replaced.

It is critical that you adhere to the standards of your local government on this matter.

You can check to see whether this is the case or if it was created incorrectly.

The newest technology, equipment, method, and septic tank design may all be utilized by a competent contractor to discover the best answer to this problem.

When replacing a baffle, it is important to be careful not to harm the tank wall when removing the concrete remnants of the baffle. This is especially true for ancient tanks. It is possible that replacing your baffle will also assist you in determining whether or not your tank requires replacement.

How much will replacing the baffle cost you?

Depending on where you are located, the cost of baffle replacement may differ. However, the average cost should be $100, however you may have to pay up to $300-400 on rare occasions. Other elements that may influence expenses include the plumber or septic tank firm with whom you are working and the type of baffle and tank involved, as well as any municipal or state baffle replacement standards that may be in effect. Other cost variables, such as the materials used, the soil types in your house, the time of year, and the urgency of the repair or replacement requirement, may also be considered.

It may be more expensive to replace the baffle during snowy weather since it takes more effort to reach the septic system, resulting in a higher labor cost.

Frequently asked questions about baffle on septic tank

This is because it prevents sediments from exiting the tank and entering the leach field, where they may produce a clog in the system and lead it to fail. This is a serious concern since rebuilding a leach field is an extremely expensive endeavor. Unfortunately, this is the first piece of the puzzle to come away. A septic tank intake baffle is positioned at the junction of the septic tank and the main sewage line for the residence. Its purpose is to guarantee that wastewater enters the tank smoothly and without disturbing the scum layer at the bottom of the tank.

How to know if the septic tank is clogged?

The level of water is rising. Instead of clogging, drainfield pipes that crack open and burst open unleash an excessive amount of water over the field area. Puddles, as well as spongy and mushy ground, may be observed throughout the area. It is also possible for water levels within the baffle of a septic tank to rise as the consequence of a clogged or crushed drain field.

What are the possible causes of leaks in a new baffle tee?

Leaks at the new baffle tee are prevented by proper sealing. Groundwater, in addition to wastewater, has the potential to flood and harm the system. A sewage backup into the building occurs in the worst case scenario. If you find any signs of a leak in your new baffle tee, it is highly suggested that you contact a competent septic tank service.

How do I go about a septic tank with an inlet pipe but no tee?

You can increase the size of the entrance hole on the tank’s side and add a tee at the same time. To fit inside the outlet pipe, you might purchase a polyethylene pipe tee with a lower male insert diameter than the pipe tee you now have. It may be necessary to remove a portion of the current pipe if this is not practicable. This will allow you to create more space in the septic tank wall, which will allow you to place and seal the new tee.

Is it safe to remove an inlet baffle from a septic tank?


Never remove an intake baffle from a tank without first consulting the manufacturer. An obstruction at the septic tank entrance may cause a sewage backup into the building, which would be quite unpleasant.

The Bottom Line

At some point, your septic tank will require maintenance or repair. It is possible that the baffle needs to be replaced or that the lid needs to be repaired. The argument is that prevention is always preferable to treatment. After all, why wait until you have to spend additional money to repair or replace a full septic tank, which might be quite expensive, when you could only fix a malfunctioning baffle? You’re well aware of the steps necessary to repair your baffle. It is imperative that the whole tank be replaced as soon as possible.

Leave a Comment

Your email address will not be published. Required fields are marked *