- One of the best ways to pinpoint exactly where the septic tank is on your property is to perform a records search. If you still have a copy of your original home inspection, there may be an attached document called the “as-built.” This diagram will show exactly how far from the house the septic tank was installed.
How do I know if my septic tank has a pump?
Standing Water The most common places for this to occur are in the area around the septic tank and/or the drainfield. If you have water pooling in these areas, this is a sure sign that you need your septic system pumped and inspected immediately.
Does every septic system have a pump?
Does Your Septic System Require A Pump? Generally, a septic pump isn’t needed if the waste can flow at a rate of at least two-feet per second with gravity only. Pumps are usually necessary for septic tanks that sit lower than the drain field and gravity is unable to carry and/or push the effluent out of the tank.
Are septic tank locations public record?
Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.
Can a metal detector find a septic tank?
If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.
Is my septic tank full or clogged?
If the septic tank is completely clogged, water will back up into the house quickly. If the septic tank is only partially clogged, the drains will become slow as the water struggles to wind its way down into the septic tank.
What are signs of septic tank problems?
7 Warning Signs Your Septic System Is Failing
- Gurgling Pipes. They would occur when you run water in the house (e.g. when using the sink or shower) or flush the toilet.
- Bad Odours. It’s never a pleasant experience when this occurs.
- Water At Ground Level.
- Green Grass.
- Slow Drainage.
- Blocked Pipes.
How much does it cost to pump a septic tank?
How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.
What happens if septic pump fails?
Most septic systems fail because of inappropriate design or poor maintenance. Failure to perform routine maintenance, such as pumping the septic tank generally at least every three to five years, can cause solids in the tank to migrate into the drain field and clog the system.
How long does a septic pump last?
The average life expectancy is 5 to 7 years for a residential sewage pump and 5 to 15 years for a commercial sewage pump. Life expectancy of the pump depends on many different factors, some of which are the quality of the pump, how often the pump has to run, and the electrical supply to the pump.
How do you find a septic tank in an old house?
Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.
Do I have to change my septic tank?
Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.
How do I find my septic lateral lines?
Call your local electric utility provider or gas company to locate buried gas or utility lines before digging. A septic tank probe can also help you find the location. Stick the long, thin metal probe into the ground until you feel it hit the tank and feel the edges of the tank.
Can I drive over my leach field?
Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.
What can I use to find my septic tank?
In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid.
How To Find Septic Tank Location: A Guide for Property Owners
The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.
Follow the Main Sewer Line
Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.
If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.
Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.
Inspect Your Property
Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.
If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.
Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.
- Paved surfaces
- Unique landscaping
- Your water well, if you have one
- And other features.
If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.
Check the Property Records
Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.
Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.
Don’t Try to Fix Septic Tank Issues Yourself
Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.
Schedule Septic Tank Maintenance
The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.
We are open seven days a week, twenty-four hours a day.
Frequently Asked Questions
A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.
How do I know if I have a septic tank?
Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.
If you’re also using well water, it’s possible that you won’t receive one at all.
What do I do once I locate my septic tank?
If there are no visible signs that you may have a septic tank – such as uneven landscaping in your yard – there are a few ways to find out if you do or do not have a septic tank. Checking your property records is the most reliable technique to ensure that you are utilizing the correct equipment. When you acquired your house, you should have received a map of the septic system with the property documents. Checking your utility statement is another approach to determine this information. The public utility services should not issue you a water bill because your septic system is part of your wastewater management system.
In fact, if you’re also using well water, you might not even get one. It is likely that you are connected to well water rather than the public sewer system if you do not have a meter linked to your water supply.
How to Check Your Septic Panel and Pump Chamber
It is recommended that you inspect your pump chamber once a year to ensure that everything is in proper working order. Follow the 11-step procedure outlined below to complete this task on your own! (Do you require further assistance? Alternatively, you may watch our instructional video below.)
1. Let’s start by inspecting the panel. Make sure the power is on by verifying the power switch to the panel is on.
The following items should be included in this general overview: The electrical box may be seen in the lower left corner of the image below, starting at the bottom of the image. Check to verify that all of the cables are firmly connected before using it. Next, take a look at the lower right corner of the shot, where you can see the discharge pipe for the pump. Check to see if it is operational (valve should be lined up with pipe). It’s now time to have some fun!
FIRST.PUT ON GLOVES!That is one step you DO NOT want to miss. Remove the float tree (the pipe with a pvc handle located upright left in our picture) and pull up the alarms.
*Please keep in mind that these instructions are for a 4-float system. Some systems contain only two or three floats.
If you don’t hear an alarm, this is cause for concern. Starting at the top, I will explain the floats and how to ensure each one is working.
NOTE: If your water supply is depleted, you may need to replenish it. Fill it up a little with water from a yard hose.
7. Continue testing.
If your water supply is running low, you may need to top it off with more water. Fill it up with water from a yard hose.
8. Now is the time to inspect the power cords.
Check to see that everything is securely tied to the float tree and not just hanging free. Zip ties can be used to reattach any stray cables.
9. Securely return the float tree to its holder and coil any dangling cords so that they are out of the water.
- What is a septic tank
- How do I know if I have a septic tank
- And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
- What to Do Once You’ve Discovered Your Septic Tank
You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.
- “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
- When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
- The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
- In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.
How to Locate Your Septic Tank
Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.
What Is a Septic Tank?
Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.
Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.
How Do I Know If I Have a Septic Tank?
What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.
- A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
- A septic system is likely to be installed in your home if you reside in a rather rural location.
- Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
- When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
- Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.
Why It’s Important to Know the Location of Your Septic Tank
You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:
1. To Be Able to Care for It Properly
The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.
2. If You Want to Landscape or Remodel Your Property
If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.
For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.
3. If a Problem With Your Tank Occurs
Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.
4. Ease of Getting It Fixed
Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away
1. Use a Septic Tank Map
First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.
- If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
- The county health department is responsible for keeping track of septic systems.
- A septic tank’s position could be depicted on a survey map, for example.
- The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.
2. Follow the Pipes to Find Your Septic Tank
Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.
- In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
- By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
- The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
- Going via the sewage line itself is another method of locating the septic tank utilizing it.
- Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
- When the snake comes to a complete halt, it has almost certainly reached the tank.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.
If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.
3. Inspect Your Yard
Whether or not there is an existing map of your septic tank on hand, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to search down and find the tank. Following the sewer lines that lead away from your property is one method of accomplishing this. The septic tank is situated along the sewage line that runs from your home and into your yard, as we’re sure you’re well aware. You should be able to locate a four-inch sewer pipe in your home’s basement or crawl area, which will direct the flow of waste to your septic tank.
- A four-inch-diameter pipe that exits your home via a basement wall is generally what you’re searching for, but specifics vary.
- Sticking a thin metal probe (also known as a soil probe) into the earth near the sewage line can allow you to track the pipe’s location.
- A typical septic tank is located between 10 and 25 feet away from your property, with no tank closer than five feet to your residence.
- An alternative method of locating the septic tank using the sewage pipe is to pass through it.
- Instead, use a drain snake, which is similar to what you would use to unclog a toilet or drain.
- Most likely, the snake has reached the tank by the time it pauses.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns along its length.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet to direct you to the tank.
- Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
- Directly in front of the home Immediately adjacent to your well (if you have one)
- In close proximity to trees or densely planted regions
- In the shadow of a patio, deck, or other building
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.
Depending on the quality of your septic system, the grass in the vicinity of the tank may be more lush and vigorously growing. Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.
4. Talk to Your Neighbors
If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.
5. Look for Your Septic Tank Lid
It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.
The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.
What to Do After You Find Your Septic Tank
Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.
1. Mark Its Location
The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities.
In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position. Keep the map or diagram with your other home documents in case you need it in the future.
2. Take Care of Your Septic Tank
Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.
In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.
For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.
Call a Professional Plumber
Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.
Request an Estimate for the Job
Does Your Septic System Require A New Pump?
A septic tank’s waste and sewage are evacuated from it and discharged into a drain field, either by gravity or with the assistance of a septic system lift pump. In most cases, a septic pump is not required if the waste can flow at a rate of at least two feet per second through the system using gravity alone. Pumps are typically required for septic tanks that are located lower than the drain field and for which gravity is unable to transport and/or force the effluent out of the tank due to its location.
Know If Your System Uses A Septic Effluent Pump Or Septic Grinder Pump
Knowing what sort of pump your septic system is equipped with is critical to the overall operation of the system. A septic effluent pump is a device that transfers waste from a septic tank to a drain field. A septic grinder pump is responsible for the grinding and movement of human waste and toilet paper. Septic tank businesses in Gainesville, FL such as Jones PlumbingSeptic Tank Service can help if you’re not sure what sort of pump the system is using or where it’s located in the system.
Our professionals will identify the pump and check the septic system in order to notify you of the procedures that need to be taken in order to keep all components in proper operating order.
How Septic Pumps Work
A septic pump is a sort of submersible pump that is installed in either the last chamber of the septic tank or in a separate chamber outside the main tank of the system. As waste builds up in the chamber, it activates a float switch, which then activates the septic pump. After that, waste is forced up the outflow pipe and into the drain field by an impeller. Installing a septic tank pump alarm is an excellent strategy to avoid having to clean out your septic tank on a regular basis. One of our professionals will connect the float switch to an alarm panel, which will sound if the pump fails for any reason during the installation.
This alarm will ring and notify you if there is a sewage backup in your home.
Maintenance For A Septic Pump
The upkeep of a septic pump goes hand in hand with the upkeep of a septic system in its whole. Never drain or flush any of the following common home objects to avoid the need for emergency septic service and to ensure the pump’s long-term functionality:
- Baby wipes
- Cat litter
- Fats, oils, and/or grease produced by or utilized in the preparation of meals
- Dental floss
- Personal hygiene products
- And Q-tips or other cotton swabs are all recommended.
In addition, avoid using the garbage disposal because this can cause the septic tank to fill up more rapidly and force water into the tank, among other things. If there is an excessive amount of water entering the septic system, it can cause sediments to enter the septic pump, resulting in a probable blockage in either the pump or the drain field. If or when this occurs, contact Jones PlumbingSeptic Tank Service for prompt and dependable septic tank repairs.
Common Septic Pump Issues
Even with proper maintenance, a septic pump can develop a variety of problems over time, including the following:
Noise Or No Noise
There are occasions when it is possible to hear the septic pump operating within the chamber itself. Do not hesitate to contact us for septic service if it appears that the pump is having difficulty or is failing to transport waste effectively.
Leaking Into The Septic Tank
The septic pump is equipped with a check valve, which provides a pressure gradient in order to keep the waste flowing through the pump and into the drainage system. Whenever the valve wears down or breaks, waste is forced back into the septic tank, causing the tank to overflow and back up into the pipes.
Faulty Float
Floats can become stuck open or closed, or they might become damaged as a result of material entering the septic tank. Depending on the extent of the damage, a professional from Jones PlumbingSeptic Tank Service may be able to remove the debris or may need to replace the float entirely.
Burnt Out Motor
If the motor within the septic pump burns out or fails, the pump will be unable to transfer waste, even if the energy is still being supplied to the device, since the waste would be trapped. In most cases, replacing the pump will address the problem.
Installing A New Septic Pump Or System
Jones PlumbingSeptic Tank Service will replace your septic tank if it is essential, and they will also install a new pump. Everything begins with an application, which is needed by the Florida Department of Health.
We will always assist you in filling out the application and applying for any permissions that may be required. Our professionals will be pleased to walk you through the procedure and answer any questions you may have along the way.
Septic Tank Service
Jones PlumbingSeptic Tank Service can solve any septic issue, regardless of whether your sewage system currently has a pump or if you’re interested whether installing a pump will increase the system’s overall efficiency. When performing septic tank repairs in Gainesville, our specialists take into consideration the demands of the family or company. Call Jones PlumbingSeptic Tank Service immediately to make an appointment for septic service!
How to Find Your Septic Tank
Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.
5 Ways to Find Your Septic Tank
1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.
- 3.
- Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
- Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
- When you do, that’s when your septic tank comes into play!
- Look for the Lid.
- You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
- Those areas should be excavated in order to disclose the lids.
- Get in touch with the pros.
- Lifting concrete lids will necessitate the use of specialized equipment.
- A fall into an unprotected septic tank has the potential to be lethal.
- Produce your own diagram of your yard, which you may file away with your other important house paperwork.
That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!
How to Locate a Septic Tank
A surprising number of homeowners have had to figure out how to find the location of a septic tank on their premises. If you’re purchasing a home with a septic system or discover that your property’s tank hasn’t been maintained in years, you’ll want to know where the tank is located because all septic tanks must be pumped at some point in time. In the course of a real estate transaction, the property owners or real estate agent may be aware of the location of the tank. Inquire about the “as-built,” which is a schematic of the septic system and the specifics of its installation.
Unfortunately, locating the septic tank may not be as simple as it appears.
Because septic system permits have only been needed in Oregon since 1972, you may have to depend on visual indicators to determine whether your system is working properly.
1.Follow the Outgoing Sewer Pipe
Look for the four-inch sewage pipe that runs through the structure and the location where it exits the building in the basement or crawl space. Locate the location outside the building where the pipe exits the building or the location of an access cover over the pipe. It is required that septic tanks be at least five feet away from the structure, although they are usually between 10 and 25 feet away. You may follow the pipe all the way to the tank using a metal probe. It is important to note that sewage lines may curve and run around the corner of a building rather than following a straight path to the holding tank.
2.Search for Septic Tank Risers and Lids
Depending on their age, septic tanks are either one- or two-compartment structures. Each compartment has a cover, with two additional lids for dual-compartment tanks that were added later. If the tank includes an access point known as a riser, the lid may be readily visible from outside. Look for round, plastic discs that are about a foot or two in diameter. Due to the fact that the lids might be flush with the ground or just a few inches above it, they can get overrun with grass and other plants over time.
Tanks without risers are likewise equipped with lids, however they are located underground.
3.Find the Drain Field First
In the absence of a riser and lid, search for indicators of a drain field, such as an area of grass that grows more quickly or more slowly than the rest of the yard, grass that is a different color from the rest of the yard, or areas where snow melts more quickly than in other parts of the yard. Spots of high or low ground in the yard might possibly indicate the presence of a subterranean tank or drain field. You will be able to discover the tank if you probe these regions.
Reasons to Hire a Contractor for Help
Attempting to locate a septic tank on your own can be risky, and in some cases, lethal, if the septic system is old and in danger of collapse. In the event that you fall into a cesspool, dry well, or septic tank, you will die.
Removing septic tank lids on your own might potentially put you at risk of contracting bacterial or virus diseases. If you detect any of the following issues, please contact a contractor to assist you in locating or inspecting your septic tank:
- Soil that is sinking around the tank or drain field. Drainage backup into the home’s sewer system, or toilet backup
- A foul odor in the area where you assume the tank and drain field are located
- When there is no rain, pooling water, muddy soil, or spongy grass might occur. Septic tank covers that are rusted, cracked, or have been replaced with improvised lids are prohibited.
Even though you may be ashamed about forgetting where your septic tank is, it is a very frequent problem among homeowners. A contractor may assist you in locating it, and he or she may do it as part of the pumping service. If you need assistance locating your tank or if you have any other questions, please contact us at 503-630-7802. We are available to assist you!
How to Find Your Septic Tank
Many folks have contacted me through e-mail (typically from across the nation) to inquire about the location of their septic tank. “I have no idea,” I generally say as a helpful response to the question. I really want to add something like, “It’s just off your driveway, near that bushy thing,” or anything along those lines. But, truly, even for the most experienced searchers, septic tanks are difficult to come by. The following are some strategies you might employ to assist you in locating your tank.
- Precaution should be exercised before you get started.
- So, proceed with caution!
- Please let me know if you have any queries or need assistance.
- Get to know the beast!
- tanks are normally buried 4 inches to 4 feet below the surface of the ground.
- You might be astonished to hear that someone knows exactly where it is hidden in plain sight.
- It is against the law to dig or probe in your own yard without first locating and marking the underground services.
You will receive the following tools to aid you in your search: Measurement tape, tile probe, and a shovel (if you are ambitious) The following tools are required: a metal detector (borrow or rent one since septic tanks often include iron steel rebar in the lids), and a hoagie sandwich (because locating sewage tanks makes you hungry.trust me on this).
- Examine the basement wall to see where all of the pipes join together and exit through the basement ceiling.
- If you don’t have a basement, walk outdoors and check for the roof vents on your house.
- Ordinarily, the sewage line that leads to the septic tank will exit the home right below this ventilation opening.
- On sometimes, the ancient proverb “The grass is always greener on the other side of the septic tank” is true.
Your tank may be located by probing or digging for it, and with luck, you will locate it. Keep in mind that not everything that seems to be a septic tank actually is! It’s possible that you came upon one of the following instead:
- Rubble buried in the ground (not to be confused with Barney Ruble)
- SepticDrywell
- An old foundation
- In case you happen to live in a cemetery (which is spooky), you may use a grave vault to keep your belongings safe.
After a few hours of hopelessly digging about in your yard, it will be time to eat your hoagie and take a little sleep. Following that, it will be necessary to rent or borrow a metal detector. In the event that your next-door neighbor loves Star Wars action figures or has more than three unidentified antennae on his roof, there is a significant probability that you can borrow his metal detector. If you’re lucky, the metal detector will really assist you in finding your septic tank, rather than simply a bunch of old buried automobile parts.
- According to local legend, a pumper known as “Zarzar The Incredible” can locate sewage tanks using a metal measuring tape spanning 30 feet in length.
- Continue to press your commode (“commode” sounds sophisticated) tape deeper and farther down the pipes until he “feels” the bottom of the tank with his tape.
- I recently acquired locate equipment that can be used to locate septic tanks, and I’m excited about it.
- For further information, please contact me at 574-533-1470.
- After that, you may have a movie of the inside of your sewer pipes created!
- Related: Visit our Septic System Maintenance page for more information.
- Services provided by Meade Septic Design Inc.
- Both Clients and Projects are included.
- Send me an email!
How to Find the Lid on a Septic System
All septic tanks eventually fill with sediments and must be pumped out on a regular basis in order to remain in excellent functioning order. If the tank’s lid is not on a riser at ground level and you are not the home’s original owner, you may be unable to determine where the lid is located. A typical septic tank is 4 inches to 4 feet underground, with all of its components, including the cover, buried between 4 inches and 4 feet underneath. This is true regardless of whether the septic tank is equipped with special risers that keep the lid flush with the surface of the ground.
Consult A Map
First, choose with the most straightforward choice. The installation of septic tanks at all locations is recorded in most counties’ permission records, which are kept on file for future reference. Typically, this will include a schematic indicating the placement of the tank on the land, as well as certain dimensions that will allow you to measure to the precise site of the tank.
If your tank was placed before your county made it a requirement to record the location of such tanks, you may find yourself with nothing to show for your efforts. When you acquire a house, a schematic of your septic system may also be included as part of the home inspection process.
Search For A Sign
Septic tanks are placed in such a way that they are as unnoticeable as possible on the land. After the grass has grown back after installation and some time has passed, it is possible that just a few visual indications will remain. Pay particular attention to the contours of your yard for any inexplicable high or low points that might suggest the presence of an underground storage tank.
Follow The Pipe
Installation of the septic tank takes place along the sewage line that runs from the house into the front yard. Locate the 4-inch sewage pipe at the point where it exits the home in the basement or crawl space, if it is there. Locate the same spot outside and make a note of it. Insert a thin metal probe into the earth, identify the 4-inch sewage line, and follow it across the yard, probing every 2 feet, until you reach the end of the property. Septic tanks are required to be at least 5 feet apart from the home in all states except Alaska.
Whenever the probe makes contact with flat concrete, fiberglass, or polyethylene it indicates that the tank has been located.
Locate The Lid
The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Investigate the tank’s circumference to determine its boundaries and outline the rectangle’s boundary using a pencil. A septic tank that was built before 1975 will have a single concrete lid that is 24 inches in diameter in the center of the rectangle. If the tank was built after 1975, it will have two covers made of fiberglass or polyethylene, centered at the ends of the rectangle and centered at the ends of the rectangle.
Call A Professional
Opening a septic tank is a job best left to the pros once the lid has been discovered. Concrete septic tank lids are extremely heavy, and many require the use of lifting tools to remove them completely. An open tank has the potential to release toxic gases. Anyone going around on the property who comes into contact with an exposed septic tank might be in risk. Because of the noxious vapors present in an open tank, falling into one can be lethal.
Mark The Spot
Make a note on the ground near where the tank was pumped by a professional and the lid was buried to serve as a reference in the future. In order to keep track of where you are, you should choose a hefty circular patio tile that is embedded in the ground. Additionally, draw your own map of the area and store it with your other important papers.
What you should expect when your septic tank needs pumping
The following are general recommendations: It is advised that you pump your septic tank every two to three years. The frequency with which you pump is determined by the volume of water you utilize. Generally speaking, the more individuals that use your septic system, the greater the increase in water flow.
As a result, your septic tank will fill up more quickly, necessitating more regular pumping. It is likely that the septic tank will need to be pumped more frequently than every two to three years. Learn about the operation of your septic tank.
Choosing a certified pumper
We recommend that you identify your septic tank before contacting a pumping company. Here is a list of questions you should ask the pumper about their services that we recommend you ask:
- What is the approximate cost of the pump-out
- And Will additional gallons be charged if the septic tank has a capacity more than 1,000 gallons? Is it included in this price the expense of excavating to expose the septic tank lid(s)
- If not, do you charge by the foot or by the meter? How much do you charge to dig you out if you don’t have one
- Is there a charge for dumping costs included? Was it determined that this fee includes a visual check of the septic tank’s entrance and exit baffles? Do you charge an additional fee for cleaning the filter baffle? If a tank has not been properly maintained, is there an additional price for the additional water and time necessary to pump it out? (for example, pumped on a regular basis)
- Please specify the distance and elevation to where the Pumper’s vehicle will be stationed if you have a long distance to pump or if you will be pumping up a steep hill (for example, in your driveway or in the yard). The Pumper will decide whether or not the vehicle is capable of providing this sort of service. Is pumping the pump tank a frequent component of your routine maintenance? What is the cost of providing this service? It is recommended that a pump tank be pumped in addition to the septic tank, cleaned with water, and then dried with a blow dryer. If the pump tank is extremely full, you may be subject to an additional price.
Locating the septic tank
Once you’ve decided on a Pumper, you’ll need to locate the septic tank on your property. Most Pumpers will charge you for the time it takes to locate the tank and open the septic tank lid (s). You can perform the necessary work to expose the septic tank lid(s) prior to the arrival of the Pumper. In order to make septic tank pumping and inspection trips easier and less time-consuming, the Ohio Department of Public Health advises that you install “risers.” With locking gas tight lids linked to both the tank and the riser and access raised to the surface, there is no digging required every time the septic tank needs to be pumped.
The majority of septic system pumpers will be able to do this service for you.
Both compartments must be examined and pumped in order to meet the requirements.
The location of your septic tank will be straightforward if you have an as-built (a map of your septic system) for your system.
The following talents will be required by you or your Pumper if an as-built is not available: investigation
- If there is a crawl space, you may be able to locate the tank by determining where the plumbing exits the foundation wall and then using a probing bar to locate it. If you have a fiberglass or polyethylene tank, a probe bar is not suggested unless extreme caution is exercised when using the probe bar. Probing will only be effective if the tank is not more than 1 to 2 feet below the surface of the ground
- If there is no crawl space available, you may occasionally discover the tank by looking for the plumbing vents in the roof. A person who is walking behind the home and coming from a restroom can find themselves at the exit point of the sewage line that connects to the septic tank
Using an electronic detecting equipment may be essential if none of the above mentioned approaches prove successful. Some rental services contain a transmitter that may be flushed down the toilet and is detected by a receiving unit, which can be found in some rental services. In certain cases, drainfield location is the specialty of septic system contractors. See a list of septic system installers who are certified. As long as the tank is exposed, sketch a map depicting the location of the septic tank lid(s) in relation to the home and make a copy of the map for your records.
Pumping the septic tank
Before the Pumper begins the process of pumping out the tank, you may request that he measure the thickness of the scum and sludge layer layers on the inside of the tank. Using this method, you can determine the pace at which the particles collect in the tank, which will assist you in determining when it is necessary to have the septic tank pumped again. Pumping frequency will be in the range of 2 to 3 years for the vast majority of families. It doesn’t matter how often you pump your septic system; frequent inspections will provide you peace of mind that everything is in working order inside those tanks.
Concerning the inspection of your septic system. The septic tank Pumper should present you with a receipt that details the services that were done to your tank. This receipt should contain the following information:
- The company’s name, address, and phone number
- Pumper’s certification number
- Number of gallons that were pumped in an approximate manner the number of compartments that have been pumped In good working order, the tank baffles In-tact condition of the septic tank
- Provide specifics on any work performed on baffles or access lids. This information should be included on the pump receipt if the scum and sludge layers were measured. Any work done on the septic tank or pump tank should be documented. Any additional service work that is completed
