Go to your basement or crawl space, and then look for the main sewer line that leads to your septic tank. Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside.
How do you find a septic tank in an old house?
Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.
Will a metal detector find my septic tank?
If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.
Are septic tank locations public record?
Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.
How deep is a septic tank in the ground?
Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.
How do you tell if your septic tank is full?
Here are some of the most common warning signs that you have a full septic tank:
- Your Drains Are Taking Forever.
- Standing Water Over Your Septic Tank.
- Bad Smells Coming From Your Yard.
- You Hear Gurgling Water.
- You Have A Sewage Backup.
- How often should you empty your septic tank?
Does every house have a septic tank?
A septic tank is a crucial part of a home’s septic system. In the U.S., about 20% of homes use a septic system to manage their wastewater. Septic systems are most commonly found in the Eastern U.S., with homes in rural areas of New England being the most likely to have a septic system present.
How far is septic tank from house?
Requirements vary from one area to another, but the normal minimum distance from the house is 10 feet. If you’ll be using a private well for drinking water, however, note that many state departments of health require a minimum of 50 feet between a new septic tank and a well, according to APEC Water.
Should septic tank lids be buried?
In most cases, all components of the septic tank including the lid are buried between 4 inches and 4 feet underground. Unless the septic tank has special risers that position the lid at ground level, you’ll have to dig for it.
Can you use a metal detector to find sewer lines?
Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. The best and easiest way to find below-ground objects such as these is with a metal detector.
Are septic tanks metal?
Steel Septic Tank—Steel septic tanks are the least durable and least popular tank option. Designed to last no more than 20-25 years, they can be susceptible to rust even before that. Steel top covers can rust through and cause an unsuspecting person to fall into the tank.
Are septic tanks made of metal?
The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.
What is OWTS?
An Onsite Wastewater Treatment Systems (OWTS) is a privately owned and maintained sewage disposal system. They are commonly referred to as septic systems. All OWTS have two basic components: a two-compartment septic tank and a disposal field.
Do I have to change my septic tank?
Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.
Do homes in LA have septic tanks?
Thousands of houses throughout Southern California have septic systems.
How to Locate Your Septic Tank
It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.
This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.
How To Find A Septic Tank: Step By Step
The fact that one of the largest and most visible elements of your whole plumbing system is simultaneously one of the most difficult to locate may seem impossible to believe, but when your property is served by a septic system, this is exactly true! There’s a solid reason for this: septic tanks are huge, unattractive, smell unpleasant, and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable area on your property and hides what would otherwise be a blight on your neighborhood.
You may identify your septic system using this blog, which eliminates the need for any time-consuming, labor-intensive digging.
1. Gather Some Helpful Tools
Even while it may seem impossible to imagine that one of the largest and most visible components of your complete plumbing system is also one of the most difficult to locate, this is definitely true if your home is served by a septic system. There’s a solid reason for this: septic tanks are huge, unattractive, smell horrible, and exude an air of filth that isn’t entirely unwarranted. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable area on your property and hides what would otherwise be a blight on your landscape.
- This site is dedicated to assisting you in locating your septic system without the need for any tedious digging.
- It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath.
- You should be able to locate your septic tank anywhere between 5 and 25 feet away from your residence.
- Septic tank covers are often located at or slightly below ground level, and they are not usually visible to the human eye due to their construction.
While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.
2. Use a Septic Tank Map
If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.
3. Start Ruling Areas Out
The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:
- There are some restrictions that state exactly where a septic tank cannot be built in order to prevent major harm to your property or tank from taking place. The following will not be true of your septic tank:
4. Inspect Your Property
If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.
When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.
The likelihood of your septic tank being discovered in a few specific locations is quite high.
- Your water well, if you have one (for a variety of reasons that are rather clear)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
- Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping
5. Inspect Your Yard
A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:
- If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
- Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.
The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.
6. Follow Your Sewer Main/Sewer Pipes
Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.
The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.
If the line is labeled, it is usually made of plastic or rubber. It is important to determine where this line exits your property and in which direction it is moving, as it often travels straight out to the septic tank itself.
7. Check Your Property Records
Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.
If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.
What to Do Once You Find Your Septic Tank
Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities. You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!
How To Find My Septic Tank
- What is a septic tank
- How do I know if I have a septic tank
- And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
- What to Do Once You’ve Discovered Your Septic Tank
What is a septic tank; how do I know if I have a septic tank; what is the best way to maintain a septic tank; what is the best way to maintain a septic tank In this article, we will discuss why it is important to know where your septic tank is. The Best Way to Find a Septic Tank Following the discovery of your septic tank, what should you do?
How to Locate Your Septic Tank
Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.
What Is a Septic Tank?
Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.
Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.
How Do I Know If I Have a Septic Tank?
What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.
- A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
- A septic system is likely to be installed in your home if you reside in a rather rural location.
- Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
- When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
- Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.
Why It’s Important to Know the Location of Your Septic Tank
You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:
1. To Be Able to Care for It Properly
The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.
2. If You Want to Landscape or Remodel Your Property
If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.
For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.
3. If a Problem With Your Tank Occurs
Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.
4. Ease of Getting It Fixed
Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away
1. Use a Septic Tank Map
First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.
- If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
- The county health department is responsible for keeping track of septic systems.
- A septic tank’s position could be depicted on a survey map, for example.
- The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.
2. Follow the Pipes to Find Your Septic Tank
Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.
- In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
- By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
- The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
- Going via the sewage line itself is another method of locating the septic tank utilizing it.
- Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
- When the snake comes to a complete halt, it has almost certainly reached the tank.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.
If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.
3. Inspect Your Yard
Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:
- Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
- Directly in front of the home Immediately adjacent to your well (if you have one)
- In close proximity to trees or densely planted regions
- In the shadow of a patio, deck, or other building
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.
Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.
4. Talk to Your Neighbors
Following the elimination of potential locations for your tank, it is time to begin searching for hints as to its whereabouts. Continue to keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground storage tank. When looking at your property, you could see a hill or mound on the ground, which is usually an indication that there is a septic tank nearby. In addition, the presence of grass or other plants in your yard should be taken into consideration when selecting a septic tank installation.
A “bald patch,” or an area where the grass is having a difficult time growing, may be seen if the tank was not correctly installed.
5. Look for Your Septic Tank Lid
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for hints as to where it may be hiding. Keep your eyes peeled as you go about your property, looking for any odd high or low locations that might suggest the presence of an underground tank. For example, you could see a hill or mound on your land, which is generally an indication that a septic tank is nearby. Another consideration when selecting a septic tank is the presence of grass or other plants in your yard.
Alternatively, if the tank was not adequately buried, you may see a “bald patch,” or an area where the grass is having difficulty growing.
What to Do After You Find Your Septic Tank
Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.
However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.
1. Mark Its Location
The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.
2. Take Care of Your Septic Tank
Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.
In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.
For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.
Call a Professional Plumber
Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.
Request an Estimate for the Job
How to Find Your Septic Tank
It is not common for people to undertake their own septic system maintenance. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job properly. If you’ve attempted to locate your septic tank on your own but have been unsuccessful, it may be necessary to seek the assistance of a professional plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage system.
Please call us right away if you are suffering plumbing difficulties or if you would want to be proactive in addressing your home’s plumbing concerns. Obtain an Estimate for the Project
5 Ways to Find Your Septic Tank
1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.
- 3.
- Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
- Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
- When you do, that’s when your septic tank comes into play!
- Look for the Lid.
- You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
- Those areas should be excavated in order to disclose the lids.
Get in touch with the pros.
Lifting concrete lids will necessitate the use of specialized equipment.
A fall into an unprotected septic tank has the potential to be lethal.
Produce your own diagram of your yard, which you may file away with your other important house paperwork.
That’s all there is to it!
To book a plumbing service in Bastrop County, please contact us now!
How To Locate a Septic Tank
Customers frequently inquire about the location of a septic tank. Unless your septic tank is equipped with special risers that elevate the lids above ground level, you may need to enlist the assistance of a qualified professional. However, there are a number of things you may do to prepare yourself before calling for assistance. When it comes time to have your septic system repaired, being how to find your own septic system will save you money. Public health records can be obtained by contacting your local health department.
- These permits should be accompanied by a graphic depicting the location of the septic system’s burying spot.
- Public Records Request for the County of Nevada Request for Public Records from the County of Placer Examine the findings of your inspection report.
- Make contact with the construction company that built your home.
- Find the location of the main sewer line.
- Locate the 4 inch sewer pipe that runs through your basement or crawlspace and take a measurement of the point at which it leaves the home.
- By carefully probing the yard every few feet and following the septic pipe across your yard, you should be able to detect any problems.
- The majority of septic tanks are placed 1 to 3 feet below and are located roughly 10 to 20 feet away from the house.
An electronic metal detector can find the reinforcing bars in a concrete tank if it is built out of concrete.
Please contact us.
We have specialized technology that we can use to pinpoint the location of your tank.
You should make a note of the position of your tank for future reference if you were successful in discovering it.
A riser elevates the septic lid above the ground, making it easier to find and access your septic tank and its contents.
As a result, you will not have to pay a professional to identify and dig up the lids every time your septic system is repaired, which will help to protect your landscape and save you money.
Solved! How to Find Your Septic Tank
Istockphoto.com
Q: When I bought my home, I was told the house’s septic system needs to be cleaned out every three to five years. I recently tried to locate my septic tank, but I can’t remember where the previous homeowner said it was buried. Is there a way to find my septic tank without knowing its general location?
A:A septic tank should be pumped on a regular basis, otherwise it can create backups throughout your entire home’s wastewater system. Identifying and repairing leaks or floods might be tough if you don’t know where your septic tank is located. This can lead to more expensive problems down the road. It is possible to locate your septic tank utilizing one or more of these probable options, even if you do not know the exact location of your septic tank.
Inspect your yard for signs of the septic tank.
Going on a stroll around your property is one of the most straightforward methods of locating a septic tank. In most cases, septic tanks may be identified by checking for traces of a huge hidden item in the ground in your yard. A significant divot or hill, which frequently appears when the first hole drilled for a septic tank is either too large or too little, would be a likely clue. Examine the lawn in general, looking for areas that are spotty and difficult to grow grass or plants on. Because of the lack of a considerable amount of earth covering the tank, it is probable that the region will have minimal plant growth in the near future.
There are a few places where you don’t have to look for anything.
You can also exclude locations near any large landscaping or yard elements, such as a pool, from consideration.
Look for the septic tank lid using a soil probe.
There are either one or two lids on a septic tank, depending on whether it has a single compartment or two compartments for filtering and decomposing wastewater particles. Because these lids tend to protrude from the main tank, they may frequently be located using a soil probe (which makes for a highly effective septic tank locator tool). You may also use a piece of rebar or any other long, thin item that is firm enough to break up the dirt without exerting too much effort to break up the soil.
While probing, take careful not to drive the probe too far into the earth, since this might cause damage to the septic tank lid.
Septic tank installation companies do not all bury tanks at the same depth, so your septic tank might be put as little as a foot underground or as much as 4 feet underground, depending on the company you use.
Ametal detectors may also be used to discover septic tanks, and they may also detect the metal handles on the lids of the tanks, which can help you limit down your probing options even more.
When you have found the position of your tank, mark it with a lawn ornament, a tiny sign, or measure the distance between the two nearest corners of your property and maintain a note of this information for future reference. Associated: How Much Does a Septic Tank Cost in the U.S.?
Follow the main sewer line from your home to your septic tank.
Because septic tanks are connected to the main sewer line or waste pipe of a property, you may use the direction of the pipe to assist you locate where your tank is buried in order to locate it. Look down your basement, cellar, or crawl space to locate the main sewer line that comes into your property from the street. This pipe will typically be around 4 inches in diameter and built of cast iron or strong PVC pipe, depending on the use. When you’ve located the pipe, make a note of the location where it exits your residence.
The majority of drain pipes are built in a straight line, so you can be certain that the septic tank is buried someplace around where the main waste pipe exits the house.
A probe can assist you in confirming that you have located the tank’s position, and it is also a good idea to use a shovel to lift the lid of the tank.
Make a note of this information and put it somewhere secure so you can refer to it in the future.
Consult local county records for your home’s septic system permit.
If your septic tank is linked to the main sewer line or waste pipe of your house, following the path of the pipe will assist you locate exactly where it has been dumped. The main sewer line going into your property can be found by searching through your basement, cellar, or crawl space. In most cases, this pipe will be around 4 inches in diameter and constructed of cast iron or strong PVC pipe. Make a note of where the pipe leaves your home after you’ve found it. To get away from the house, choose the appropriate space outside and walk straight away from it.
Keep following the projected course of the drain line and keeping an eye out for any indicators that a septic tank has been buried anywhere in the vicinity.
You can mark the spot with a lawn ornament, a tiny sign, spray paint, or by measuring the distance between the two nearest corners of the house.
istockphoto.com
Check with local septic maintenance companies.
If your local government does not have any records of your septic tank, it’s conceivable that it was erected without a permit or that it is an older system that predates the necessity for a permit. If you have any questions, contact your local government. However, any septic system would have required pumping at least once every three to five years to keep it in proper operating condition.
You might reach out to local plumbing firms that provide septic maintenance services to determine if the tank has been previously pumped by them and if they are aware of where the tank is located. istockphoto.com
Ask your neighbors or contact a professional.
Unless your local government has records of your septic tank, it is probable that it was erected without a permission or that it is an older system that was established before permit requirements were in place. However, any septic system would have required pumping at least once every three to five years to keep it in excellent operating condition. You might reach out to area plumbing firms that provide septic maintenance services to determine if the tank has previously been pumped by them and if they are aware of where the tank is located.
How to Find a Septic Tank With a Metal Detector
Unless your local government has records of your septic tank, it is conceivable that it was erected without a permission or that it is an older system that predates the necessity for a permit. However, any septic system would have required pumping at least once every three to five years to maintain proper operation. You might go out to area plumbing firms that provide septic maintenance services to determine if the tank has been previously pumped by them and if they are aware of where the tank is.
How do septic systems work?
A septic system is made up of two parts: the septic tank and the drain field (or leach field).
Septic Tank
Waste from toilets, sinks, and showers is sent down a main sewage line and into a holding tank known as the septic tank. A septic tank is a large, subterranean container that acts as the initial stage of a home’s sewage treatment system by collecting and treating sewage. Watertight containers such as concrete, steel, plastic, and fiberglass are used to construct the tank. Until the particles and liquids separate into three different layers, sewage is allowed to remain in the septic tank. This picture shows how sewage from the home drains into a two-compartment underground septic tank.
The liquid wastes are subsequently discharged into the drain field.
The bacteria produce a sludge that is “digested” and stays in the tank until it is drained.
This stratum is referred to as effluent in most circles.
Drain Field
Drain fields are composed of layers of gravel and dirt that allow liquid sewage to flow down. It eventually becomes part of the groundwater supply. Aerobic bacteria (bacteria that require oxygen to survive) and other microbes decompose the organic debris that remains.
What happens if a septic tank gets too full?
In the event that your septic tank becomes overflowing, sewage may back up into your home. It is more difficult to breakdown sludge than it is to collect it. If the sludge isn’t cleaned, the solids will build up until they overflow into the drain field, causing the drain to back up. This has the potential to clog pipes and produce a backup. The sludge must be cleared on a regular basis in order to avoid this.
Many households only get their tanks emptied after the system malfunctions. Waiting until that stage can result in repair expenses in the tens of thousands of dollars. Every three to five years, we suggest that you have your septic tank pumped.
6 Steps to Locate a Septic Tank
Water from your toilets, sinks, and showers is collected in a main drain pipe and disposed of properly. This line departs your home and enters your septic tank through the basement or crawl area where it was installed. Find the line in question. Afterwards, walk outside and look for the identical location on the opposite side of the wall. Make a note of this spot since you’ll need it in a moment.
2. Check Permits and Public Records
The majority of county health agencies keep public records of septic system installation permits on their websites. These permits must be accompanied by a schematic or design depicting the proposed location of the septic tank and drainage field systems. They also give a description of the tank’s dimensions and construction material. Having this information can be quite beneficial when trying to locate a submerged tank lid. In some cases, depending on the age of your septic system and the digitization efforts of your county’s health department, you may be able to do a public records search online.
If you live in Colorado, we’ve provided links below that will allow you to check septic records in a few different areas.
- Colorado’s counties of Adams, Arapahoe, and Douglas Colorado Septic Records Search
- Colorado Permits Search
- El Paso County Records Search
- Jefferson County Septic Records Search
- Jefferson County Records Search
- Mesa County Septic Systems Search
- Pueblo County Records Search. Colorado Septic Records Search
- Pueblo County Records Search
3. Determine Septic Tank Material
If you’ve located your septic permit, you’ll find information about the size, shape, and material of your septic tank there as well. But don’t be concerned if your septic data aren’t readily available. We can perform some basic detective work to determine what material your septic system is built of. Let’s start with a look at the materials.
Types of Septic Tank Materials
Construction of septic tanks is mostly done using four types of materials: concrete, steel, fiberglass, and polyethylene plastic. Until the 1880s, the most extensively used septic tank material was concrete, which was then replaced by steel. These tanks have a lifespan of around 40 years and are built to last. They are susceptible to cracking, however, in locations where temperature variations are strong and frequent. Concrete tanks are frequently required by municipalities that have strict requirements on septic system construction.
- Steel septic tanks begin to corrode within 20 to 25 years of installation in most regions.
- If a human or animal walks across the weakened tank, it may collapse under the weight of the person or animal.
- They will not break or corrode, however, in contrast to concrete or steel tanks.
- PlasticSeptic tanks made of polyethylene have been in use since the 1980s.
They are not susceptible to rusting and are less prone to break when compared to concrete. They are, however, not quite as long-lasting. Because of the weight of the earth above them, or because a vehicle passes over the area where they are buried, plastic tanks are susceptible to collapse.
How Old is Your House?
Next, let’s determine the approximate age of your home. In some cases, all you need to do is take a glance at the house’s façade to get an idea of how old it really is. However, you may examine the tax assessor’s records in your county to get a more precise assessment. Similarly to searching for septic records, your mileage may vary depending on which county’s digitized documents you are searching for. Let’s go over an example search utilizing Boulder County’s Property Search tool so that you can have a better sense of what you should be looking for.
- Look up your home address on the internet. When searching for a home, some programs provide separate areas for your address and street name, while others (such as Boulder County) merge the two into a single search box. Look for information on Deeds and/or Sales Records in the public domain. You’ll find a list of transactions here, with dates showing when the property was purchased and sold. Find the transaction that occurred on the earliest possible date. This is most likely the year in which your home was constructed.
This information allows you to make an informed guess regarding the sort of material that your septic tank is built of.
4A. If it’s Concrete or Steel, Use a Metal Detector
After coming to the conclusion that the tank is most likely built of concrete or steel in Step 3, a metal detector may be used to make the work of locating it much simpler. But not just any metal detector will do. It must be the right one. Standard metal detectors have a depth range of 6 – 8″ (15 – 20 cm) below the surface of the ground. As previously stated, the majority of septic tanks are placed 1′ to 3′ (0.3 m to 1 m) underground, putting them outside of the acceptable range. An advanced sort of metal detector known as a Magnetic Locator, which can detect objects as deep as 16′ (4.8 m), is available for purchase.
How to Use a Metal Detector to Search for a Septic Tank
After coming to the conclusion that the tank is most likely built of concrete or steel in Step 3, a metal detector may be used to make the work of locating it significantly easier. Metal detectors, however, are not just ordinary detectors. Ordinary metal detectors have a depth range of 6 – 8″ (15 – 20 cm) below the surface of the ground. In addition, as previously stated, most septic tanks are located between one and three feet (0.3 to one meter) underground, putting them outside of the floodplains’ floodplains.
Only iron and steel are detected by this device, making it perfect for identifying the iron handles and rebar in concrete septic tanks, or for detecting the walls of steel tanks.
- To begin, start at the location you highlighted in Step 1 where the sewage drain line leaves the home. From here, you may switch on the locator and adjust the gain to a high setting. Walking over the search area, sweep the locator from left to right, as if looking for anything. As you go, make a note of the regions with the strongest signal strength. It is most likely that the tank-iron lid’s handles will be located in one of these positions
- As soon as you’ve exhausted the search region in one direction, sweep over it perpendicularly and make note of the spots with the strongest signal strength. Continue on to Step 5
4B. If it’s Plastic or Fiberglass, Probe Gently
Septic tanks made of plastic or fiberglass are typically buried one to two feet (0.3 to 0.91 m) below ground level. They feature circular covers made of green or black plastic that are roughly two feet (0.91 m) wide and have a diameter of around two feet (0.91 m). Due to the fact that these tanks are totally made of plastic, a metal detector will not be of use in locating them. In this situation, a soil probe is really useful. An inexpensive soil sampling instrument, soil probes are comprised of a 4′ (1.2 m) metal rod with a pointed tip on one end and are used for soil sample.
Gently poke the earth with a soil probe every 2 to 3 feet, using a light touch (0.61 to 0.91 m).
Make a note of any areas where you encounter resistance and continue exploring around in your search area. The use of a soft touch is essential here, since the metal tip of the probe can cause damage to plastic septic tanks (and sewage lines) if too much force is used.
5. Time to Dig
Following the placement of an amagnetic locator (or the probing of the ground) to record the places with the highest signal strength, you are ready to begin digging. Septic tank lids can be located anywhere from 4″ (10 cm) to 4′ (1.2 m) below the surface of the ground.
6. Mark the Location for Future Maintenance
Having discovered your septic tank, you’ll want to ensure that it can be readily detected and accessed in the event that it has to be repaired or replaced. You may accomplish this by installing a septic tank riser. Sewage Tank Risers are devices that provide for easy access to the septic tank from the ground. They are shafts made of plastic or concrete that link the top of the tank to the surface of the ground below the tank. The tank lid will no longer require you to dig to access it whenever maintenance is required.
How to Find Your Septic Tank
Many folks have contacted me through e-mail (typically from across the nation) to inquire about the location of their septic tank. “I have no idea,” I generally say as a helpful response to the question. I really want to add something like, “It’s just off your driveway, near that bushy thing,” or anything along those lines. But, truly, even for the most experienced searchers, septic tanks are difficult to come by. The following are some strategies you might employ to assist you in locating your tank.
- Precaution should be exercised before you get started.
- So, proceed with caution!
- Please let me know if you have any queries or need assistance.
- Get to know the beast!
- tanks are normally buried 4 inches to 4 feet below the surface of the ground.
- You might be astonished to hear that someone knows exactly where it is hidden in plain sight.
- It is against the law to dig or probe in your own yard without first locating and marking the underground services.
You will receive the following tools to aid you in your search: Measurement tape, tile probe, and a shovel (if you are ambitious) The following tools are required: a metal detector (borrow or rent one since septic tanks often include iron steel rebar in the lids), and a hoagie sandwich (because locating sewage tanks makes you hungry.trust me on this).
- Examine the basement wall to see where all of the pipes join together and exit through the basement ceiling.
- If you don’t have a basement, walk outdoors and check for the roof vents on your house.
- Ordinarily, the sewage line that leads to the septic tank will exit the home right below this ventilation opening.
- On sometimes, the ancient proverb “The grass is always greener on the other side of the septic tank” is true.
Your tank may be located by probing or digging for it, and with luck, you will locate it. Keep in mind that not everything that seems to be a septic tank actually is! It’s possible that you came upon one of the following instead:
- Rubble buried in the ground (not to be confused with Barney Ruble)
- SepticDrywell
- An old foundation
- In case you happen to live in a cemetery (which is spooky), you may use a grave vault to keep your belongings safe.
After a few hours of hopelessly digging about in your yard, it will be time to eat your hoagie and take a little sleep. Following that, it will be necessary to rent or borrow a metal detector. In the event that your next-door neighbor loves Star Wars action figures or has more than three unidentified antennae on his roof, there is a significant probability that you can borrow his metal detector. If you’re lucky, the metal detector will really assist you in finding your septic tank, rather than simply a bunch of old buried automobile parts.
According to local legend, a pumper known as “Zarzar The Incredible” can locate sewage tanks using a metal measuring tape spanning 30 feet in length.
Continue to press your commode (“commode” sounds sophisticated) tape deeper and farther down the pipes until he “feels” the bottom of the tank with his tape.
I recently acquired locate equipment that can be used to locate septic tanks, and I’m excited about it.
For further information, please contact me at 574-533-1470.
After that, you may have a movie of the inside of your sewer pipes created!
Related: Visit our Septic System Maintenance page for more information.
Services provided by Meade Septic Design Inc.
Both Clients and Projects are included.
Send me an email!
