How To Find A Lost Septic Tank? (Solution found)

In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid.

How do I Find my septic tank location?

  • 4 Easy Ways to Find Your Septic Tank 1 Let Sewer Pipes Lead The Way. Your septic tank and drainfield are typically installed parallel to the sewer line that extends from your home into the yard. 2 Check County Records. 3 Dig Up The Lids. 4 Schedule Maintenance. 5 Disguise The Lids.

How do I find out where my septic tank is located?

Follow the Main Sewer Line Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside. The sewer pipes will lead to where your septic tank is located.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

Can a metal detector find a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How do you find a septic tank in an old house?

Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.

How do you find a buried septic tank?

Tips for locating your septic tank

  1. If the septic tank lid is underground, you can use a metal detector to locate it.
  2. You can use a flushable transmitter that is flushed in the toilet and then the transmitter is tracked with a receiver.

How do I find out if my septic tank is registered?

Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.

Do I have to change my septic tank?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

What is OWTS?

An Onsite Wastewater Treatment Systems (OWTS) is a privately owned and maintained sewage disposal system. They are commonly referred to as septic systems. All OWTS have two basic components: a two-compartment septic tank and a disposal field.

Can I drive over my leach field?

Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.

How much does a pump for a septic tank cost?

Average Cost To Pump A Septic Tank The national average cost to clean and pump a septic tank is between $295 and $610 with most people spending around $375. Depending on the size of your septic tank, pumping could cost as low as $250 for a 750-gallon tank, or as high as $895 for a 1,250-gallon tank.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

Does every house have a septic tank?

A septic tank is a crucial part of a home’s septic system. In the U.S., about 20% of homes use a septic system to manage their wastewater. Septic systems are most commonly found in the Eastern U.S., with homes in rural areas of New England being the most likely to have a septic system present.

How far is septic tank from house?

Septic tanks are required to be at least 5 feet from the house, although most are between 10 and 25 feet away.

Any easy way to find a lost septic tank? (tanks, drains, detector) – House -remodeling, decorating, construction, energy use, kitchen, bathroom, bedroom, building, rooms

Please registerto participate in our discussions with 2 million other members – it’s free and quick! Some forums can only be seen by registered members. After youcreate your account, you’ll be able to customize options and access all our 15,000 new posts/day with fewer ads.

Location: Port Orange, Florida720 posts, read1,565,195timesReputation: 355
I bought a house that was built in 1975. The house paperwork said it has 2 septic tanks and they were cleaned 2 years ago. I didn’t have a septic inspection, now I’m wondering where the tanks are?There are no lids or manholes anywhere that I can find. I feel like an idiot for not confirming where they are before I bought the house. I have no way of contacting the previous owner. Anyone ever deal with this before? If I called a septic company would they be able to find it? Could it be partially buried?My neighbors unit sits a few inches above the ground but his house is newer than mine. Thanks in advance for any help or advise.
If there is a place in your yard where everything is a little greener, that’s the leaching field.The septic tank should be next to it.A metal detector could help you find the lid.Mine is concrete, but has a metal handle.A sewer company could run a tracing line down your sewer pipe if needed.
Location: Woodbury, TN30 posts, read178,429timesReputation: 24
When we have septic inspections done here, the inspectors flush a blue dye down all the drains. This helps them find any leaks, the septic tank, and the field lines.
Location: Port Orange, Florida720 posts, read1,565,195timesReputation: 355
Thank you for the help. I have 20 acres in my back yard. Could the lid be buried? Any idea how far away from the house it could possibly be so I can limit my search? Would the pipe from the house to the tank have been metal in 1975? I haven’t noticed any unusual green patches of growth. Anyone know what the cost can be to clean a septic tank?
24,841 posts, read35,331,822timesReputation: 11519
Check with your local heath department.They likely have records.When I check I use a prod rod.Just a thin rod about five ft long.Look under your house where the line comes out,it will give you a direction.
24,841 posts, read35,331,822timesReputation: 11519
Yes, it is buried.If you have a well it is likely on the opposite side of the house.


Last edited by Driller1; 07-25-2008 at08:00 PM.

Location: Melbourne, FL1,007 posts, read5,436,921timesReputation: 637
If you don’t have a well, look under the house and see where the main line of the sewer is going.Most likely it will be in that direction. Some places are not very obvious as they should not have any plants or buildings over the septic tank or field. but that is not always the case either.Many septic tank lids are buried.Get a poker and start probing the most likely areas.If you hit something hard, it could be it (hopefully you don’t have rocky terrain as this method probably won’t work).Most septic people are good at finding them also.Some health agencies don’t keep records that long. but it is certainly worth a try and see if they keep a septic permit on file.
24,841 posts, read35,331,822timesReputation: 11519
Quote:Originally Posted byJanecjIf you don’t have a well, look under the house and see where the main line of the sewer is going.Most likely it will be in that direction. Some places are not very obvious as they should not have any plants or buildings over the septic tank or field. but that is not always the case either.Many septic tank lids are buried.Get a poker and start probing the most likely areas.If you hit something hard, it could be it (hopefully you don’t have rocky terrain as this method probably won’t work).Most septic people are good at finding them also.Some health agencies don’t keep records that long. but it is certainly worth a try and see if they keep a septic permit on file.Michigan keep records forever.
Location: Melbourne, FL1,007 posts, read5,436,921timesReputation: 637
Quote:Originally Posted byDriller1Michigan keep records forever.That’s helpful, NC does not. That would be the easiest method.
24,841 posts, read35,331,822timesReputation: 11519
I was thinking,if there is a well,the septic tank could show on the permit or log.Even an old well.
Pleaseregisterto post and access all features of our very popular forum. It is free and quick. Over $68,000 in prizes has already been given out to active posters on our forum. Additional giveaways are planned. Detailed information about all U.S. cities, counties, and zip codes on our site:City-data.com.

All times are GMT -6.

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.

Inspect Your Property

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.

  • Paved surfaces
  • Unique landscaping
  • Your water well, if you have one
  • And other features.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.

Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.

Don’t Try to Fix Septic Tank Issues Yourself

Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.

Schedule Septic Tank Maintenance

The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.

We are open seven days a week, twenty-four hours a day.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

A septic system is a system for the management of sewage and wastewater. Water will flow out of your home through pipes until it reaches your septic tank outside your home, to put it another way. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as they decompose. Eventually, the solids will fall to the bottom of the tank, and the liquids will drain into your leach field.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis. Preventing worse problems and the need for costly repairs down the line may be accomplished via proper septic system maintenance. All of the heavy lifting has been delegated to our team of professionals.

How To Find My Septic Tank

  1. What is a septic tank
  2. How do I know if I have a septic tank
  3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
  4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

  1. “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
  2. When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
  3. The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
  4. In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

You could have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily visible. Septic tanks, for example, are an important part of your home’s design. Controlling and managing the wastewater generated by your house is the responsibility of your septic system.

“How can I locate my septic tank?” is one of the most often requested inquiries.

When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when the tank is overfilled.

A septic tank is typically buried between four inches and four feet underground, depending on the circumstances.

In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to identify where yours is.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

  • Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
  • An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
  • Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
  • Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

  1. A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
  2. A septic system is likely to be installed in your home if you reside in a rather rural location.
  3. Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
  4. When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.

Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system. Your home’s building permit and drawings will almost certainly include details concerning the existence (or absence) of a septic tank on your site.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

  1. If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
  2. The county health department is responsible for keeping track of septic systems.
  3. A septic tank’s position could be depicted on a survey map, for example.
  4. The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

In this way, if you ever decide to sell your property, you will be able to supply the new owner with everything they will need to locate the tank and properly manage their septic system.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

  1. In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
  2. By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
  3. The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
  4. Going via the sewage line itself is another method of locating the septic tank utilizing it.
  5. Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
  6. When the snake comes to a complete halt, it has almost certainly reached the tank.
  7. While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
  8. When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

3. Inspect Your Yard

Whether or not there is an existing map of your septic tank on hand, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to search down and find the tank. Following the sewer lines that lead away from your property is one method of accomplishing this. The septic tank is situated along the sewage line that runs from your home and into your yard, as we’re sure you’re well aware. You should be able to locate a four-inch sewer pipe in your home’s basement or crawl area, which will direct the flow of waste to your septic tank.

  • A four-inch-diameter pipe that exits your home via a basement wall is generally what you’re searching for, but specifics vary.
  • Sticking a thin metal probe (also known as a soil probe) into the earth near the sewage line can allow you to track the pipe’s location.
  • A typical septic tank is located between 10 and 25 feet away from your property, with no tank closer than five feet to your residence.
  • An alternative method of locating the septic tank using the sewage pipe is to pass through it.
  • Instead, use a drain snake, which is similar to what you would use to unclog a toilet or drain.
  • Most likely, the snake has reached the tank by the time it pauses.
  • While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns along its length.
  • When looking for your septic tank, you may use a transmitter that you flush down the toilet to direct you to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s going on inside.

  • Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
  • Directly in front of the home Immediately adjacent to your well (if you have one)
  • In close proximity to trees or densely planted regions
  • In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Taking proper care of your tank may save you thousands of dollars over the course of its useful life span. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system in most cases. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water in general.

Solid meals, cooking oil, and pharmaceuticals should not be flushed down the sink drain in your kitchen.

The usage of water-intensive equipment should be avoided wherever possible, according to another proposal.

How Do I Find My Septic Tank

What is the location of my septic tank?

Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00

How Do I Find My Septic Tank

Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.

A tiny proportion of septic tanks have a capacity of 3000L or more.

Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.

If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

  1. They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
  2. Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
  3. A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
  4. Using an electronic service locator, you may locate a septic tank.
  5. In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
  6. Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
  7. Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

  • There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

There are three sizes of Septic Tank available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms, respectively.

How to Find a Septic Tank

It is not easy to find a septic tank. The first thing to do is contact the local health/zoning office to see if they have a plan on record.If the system is fairly new you have a chance, but many states didn’t start keeping records until the 1990’s and even still they are spotty at best.Even if they do have a drawing on file, it probably will not match exactly what is in the ground, but it should be close.If you can find out who installed the system they should be able to tell you where to find the septic tank.If none of that pans out, then you will want to identify where the sewer main leaves the house.If you have a basement or crawl space you can look for a 4” black pipe…look where it goes out of the foundation.If you don’t have a basement/crawl space, or the sewer main is under the foundation, you will have to look for the lowest drain in the house.This is usually a floor drain in the laundry area and this is generally the area where the pipe will leave the house.Once you have an idea where the pipe exits the house you want to go outside to that part of the house and take a ¼” or ½” steel rod about 5’ long (concrete re-bar will work but a stainless steel rod is better because it doesn’t “stick” to soils as much) and start probing the ground next to the foundation until you hit the pipe.Be careful.Poke too hard and you could poke a hole in the pipe, particularly if it is older cast iron pipe.Once you find it you will want to move further out a few feet at a time to track the pipe until you find the septic tank.Tanks are usually 10 to 20 feet away from the house.Once you find the tank you will want to probe around it to get the outline.Tanks can be round, square or rectangular, but once you know the size you can start digging right in the middle.You are trying to find the manhole cover, it could be in the very center, it could be on the inlet side, it could be on the outlet side, there could be 2 or 3 covers, there could be none.Sad to say there are no standards when it comes to tanks so you get what the manufacturer had at the time.Finding the distribution box can be a little easier.It is usually about 10 to 20 feet away from the tank and sometimes you can spot it just by looking at how the grass is growing.Often the grass will grow greener over the drainfield lines and if you can see the pattern on the lawn where the lines come together, there it is.If not you can find the distribution box the same way you found the tank.However, it is seldom a snap process, it can be extremely difficult to find the septic tank and distribution box. Many is the homeowner whose yard looks like a minefield by Sunday night, and they still haven’t found the tank or d-box.The obstacles you can run into are:·Tight clay soils.Clay can be difficult not only to stick a probe into; it can be tough to pull it back out.·Rocky soils.You think you hit the tank so you start digging only to find a rock.And that can happen over and over.·Deep systems.More than 2 or 3 feet deep can be a real treat to track and dig.·Older systems.Back in the old days people did what ever they wanted.Sometimes you will find pipes that seem to twist and turn then disappear into nothing.Other times you will find something really inventive, like a Volkswagen buried in the yard and being used as a cesspool.Swear to god, it happens.This is why I suggest biting the bullet and hiring a full service contractor to find the septic tank (I say a full service contractor because some pumpers will only pump tanks, they won’t find them).And often a good contractor can tell where everything is just by the lay of the land.And if they can’t spot it by eye, they have the tools to find them easier, some even have small radio transmitters that they can flush down the drain and track as it goes through the system.And here is another thing, what happens if you do find the septic tank/d-box…what are you going to do after finding it?Do you have the tools and know-how to replace a missing baffle?Do you have a line jetter or rooter sitting in the garage? How about that 3,000 gallon pump truck to empty the tank?Probably not.Of course once you have the pro find everything, you can mark it (there are small markers you can use to landmark the system) and know where everything is.No one likes to spend money on things like locating your septic tank, but put it in perspective: if you had city sewer, you could easily spend $300 per year for sewage treatment.Over 10 years that would be $3,000.Spending $200 to $500 to have your system located and maintained is not too bad.And if you take care of your system, which means pumping the tank every 1 to 3 years, practicing wise water/chemical use, an effluent filter in the tank and a washing machine filter in the house, the cost to maintain your system could drop down to $25 per year.Not a bad deal when you think about it.

How to Find a Septic Tank With a Metal Detector

For sewage treatment in the United States, around 48% of households in rural and outlying regions depend on septic tanks or septic systems. Many of these systems have been operating without regular maintenance for many years. It is necessary to locate your septic tank in the event that sewage is backing up into your home or if your main drain line has become obstructed. Throughout this post, we’ll go over the basics of how septic systems function before showing you how to identify your septic tank in six simple stages.

How do septic systems work?

A septic system is made up of two parts: the septic tank and the drain field (or leach field).

Septic Tank

Waste from toilets, sinks, and showers is sent down a main sewage line and into a holding tank known as the septic tank. A septic tank is a large, subterranean container that acts as the initial stage of a home’s sewage treatment system by collecting and treating sewage. Watertight containers such as concrete, steel, plastic, and fiberglass are used to construct the tank. Until the particles and liquids separate into three different layers, sewage is allowed to remain in the septic tank. This picture shows how sewage from the home drains into a two-compartment underground septic tank.

The liquid wastes are subsequently discharged into the drain field.

The bacteria produce a sludge that is “digested” and stays in the tank until it is drained.

This stratum is referred to as effluent in most circles.

Drain Field

Drain fields are composed of layers of gravel and dirt that allow liquid sewage to flow down. It eventually becomes part of the groundwater supply. Aerobic bacteria (bacteria that require oxygen to survive) and other microbes decompose the organic debris that remains.

What happens if a septic tank gets too full?

In the event that your septic tank becomes overflowing, sewage may back up into your home. It is more difficult to breakdown sludge than it is to collect it. If the sludge isn’t cleaned, the solids will build up until they overflow into the drain field, causing the drain to back up. This has the potential to clog pipes and produce a backup. The sludge must be cleared on a regular basis in order to avoid this.

Many households only get their tanks emptied after the system malfunctions. Waiting until that stage can result in repair expenses in the tens of thousands of dollars. Every three to five years, we suggest that you have your septic tank pumped.

6 Steps to Locate a Septic Tank

Water from your toilets, sinks, and showers is collected in a main drain pipe and disposed of properly. This line departs your home and enters your septic tank through the basement or crawl area where it was installed. Find the line in question. Afterwards, walk outside and look for the identical location on the opposite side of the wall. Make a note of this spot since you’ll need it in a moment.

2. Check Permits and Public Records

The majority of county health agencies keep public records of septic system installation permits on their websites. These permits must be accompanied by a schematic or design depicting the proposed location of the septic tank and drainage field systems. They also give a description of the tank’s dimensions and construction material. Having this information can be quite beneficial when trying to locate a submerged tank lid. In some cases, depending on the age of your septic system and the digitization efforts of your county’s health department, you may be able to do a public records search online.

If you live in Colorado, we’ve provided links below that will allow you to check septic records in a few different areas.

  • Colorado’s counties of Adams, Arapahoe, and Douglas Colorado Septic Records Search
  • Colorado Permits Search
  • El Paso County Records Search
  • Jefferson County Septic Records Search
  • Jefferson County Records Search
  • Mesa County Septic Systems Search
  • Pueblo County Records Search. Colorado Septic Records Search
  • Pueblo County Records Search

3. Determine Septic Tank Material

If you’ve located your septic permit, you’ll find information about the size, shape, and material of your septic tank there as well. But don’t be concerned if your septic data aren’t readily available. We can perform some basic detective work to determine what material your septic system is built of. Let’s start with a look at the materials.

Types of Septic Tank Materials

Construction of septic tanks is mostly done using four types of materials: concrete, steel, fiberglass, and polyethylene plastic. Until the 1880s, the most extensively used septic tank material was concrete, which was then replaced by steel. These tanks have a lifespan of around 40 years and are built to last. They are susceptible to cracking, however, in locations where temperature variations are strong and frequent. Concrete tanks are frequently required by municipalities that have strict requirements on septic system construction.

  • Steel septic tanks begin to corrode within 20 to 25 years of installation in most regions.
  • If a human or animal walks across the weakened tank, it may collapse under the weight of the person or animal.
  • They will not break or corrode, however, in contrast to concrete or steel tanks.
  • PlasticSeptic tanks made of polyethylene have been in use since the 1980s.

They are not susceptible to rusting and are less prone to break when compared to concrete. They are, however, not quite as long-lasting. Because of the weight of the earth above them, or because a vehicle passes over the area where they are buried, plastic tanks are susceptible to collapse.

How Old is Your House?

Next, let’s determine the approximate age of your home. In some cases, all you need to do is take a glance at the house’s façade to get an idea of how old it really is. However, you may examine the tax assessor’s records in your county to get a more precise assessment. Similarly to searching for septic records, your mileage may vary depending on which county’s digitized documents you are searching for. Let’s go over an example search utilizing Boulder County’s Property Search tool so that you can have a better sense of what you should be looking for.

  1. Look up your home address on the internet. When searching for a home, some programs provide separate areas for your address and street name, while others (such as Boulder County) merge the two into a single search box. Look for information on Deeds and/or Sales Records in the public domain. You’ll find a list of transactions here, with dates showing when the property was purchased and sold. Find the transaction that occurred on the earliest possible date. This is most likely the year in which your home was constructed.

This information allows you to make an informed guess regarding the sort of material that your septic tank is built of.

4A. If it’s Concrete or Steel, Use a Metal Detector

After coming to the conclusion that the tank is most likely built of concrete or steel in Step 3, a metal detector may be used to make the work of locating it much simpler. But not just any metal detector will do. It must be the right one. Standard metal detectors have a depth range of 6 – 8″ (15 – 20 cm) below the surface of the ground. As previously stated, the majority of septic tanks are placed 1′ to 3′ (0.3 m to 1 m) underground, putting them outside of the acceptable range. An advanced sort of metal detector known as a Magnetic Locator, which can detect objects as deep as 16′ (4.8 m), is available for purchase.

How to Use a Metal Detector to Search for a Septic Tank

If you have a septic permit record, you may refer to it to figure out how far you need to go to install a septic tank. Start at the point where the drain line meets the home and work your way out to where the septic tank is shown on the diagram. Keep in mind that this graphic depicts the proposed installation area and may not accurately depict the actual ground conditions on the site. We’ll have a look at the illustration below. One inch (2.5 centimeters) is equivalent to fifty feet (50 meters).

By using a ruler to measure the design, we’ve determined that the septic tank should be roughly 13′ (3.96 m) away from the home.

  1. To begin, start at the location you highlighted in Step 1 where the sewage drain line leaves the home. From here, you may switch on the locator and adjust the gain to a high setting. Walking over the search area, sweep the locator from left to right, as if looking for anything. As you go, make a note of the regions with the strongest signal strength. It is most likely that the tank-iron lid’s handles will be located in one of these positions
  2. As soon as you’ve exhausted the search region in one direction, sweep over it perpendicularly and make note of the spots with the strongest signal strength. Continue on to Step 5

4B. If it’s Plastic or Fiberglass, Probe Gently

Septic tanks made of plastic or fiberglass are typically buried one to two feet (0.3 to 0.91 m) below ground level. They feature circular covers made of green or black plastic that are roughly two feet (0.91 m) wide and have a diameter of around two feet (0.91 m). Due to the fact that these tanks are totally made of plastic, a metal detector will not be of use in locating them. In this situation, a soil probe is really useful. An inexpensive soil sampling instrument, soil probes are comprised of a 4′ (1.2 m) metal rod with a pointed tip on one end and are used for soil sample.

Gently poke the earth with a soil probe every 2 to 3 feet, using a light touch (0.61 to 0.91 m).

Make a note of any areas where you encounter resistance and continue exploring around in your search area. The use of a soft touch is essential here, since the metal tip of the probe can cause damage to plastic septic tanks (and sewage lines) if too much force is used.

5. Time to Dig

Following the placement of an amagnetic locator (or the probing of the ground) to record the places with the highest signal strength, you are ready to begin digging. Septic tank lids can be located anywhere from 4″ (10 cm) to 4′ (1.2 m) below the surface of the ground.

6. Mark the Location for Future Maintenance

Having discovered your septic tank, you’ll want to ensure that it can be readily detected and accessed in the event that it has to be repaired or replaced. You may accomplish this by installing a septic tank riser. Sewage Tank Risers are devices that provide for easy access to the septic tank from the ground. They are shafts made of plastic or concrete that link the top of the tank to the surface of the ground below the tank. The tank lid will no longer require you to dig to access it whenever maintenance is required.

Leave a Comment

Your email address will not be published. Required fields are marked *