How To Extend A Existing Septic Tank Riser? (Best solution)

In order to put septic tank risers onto your septic tank, you need an adapter ring. Polylok has one of the largest adapter rings on the market allowing you to cover up to a 25’’ square opening or a 27’’ round opening. This ring accepts both 20’’ and 24’’ risers and gives you great flexibility no matter what size your opening may be.

Should septic tank riser be above ground?

Landscaping Around Septic Tank Risers However, septic tank risers should never be buried. Instead, they should be 2 inches above final grade to prevent groundwater from entering the system.

How far apart are septic tank lids?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

Are septic risers worth it?

Having a riser in place can also significantly reduce the cost of septic tank maintenance over time through the ease of access and time on the job saved. Plus you will be spared digging up your lawn every time as well.

Do they make square risers for septic tanks?

The Polylok square riser adapter ring is designed to connect the Polylok septic tank risers or lids to an existing concrete tank with large square or round openings.

How do you insulate a septic tank riser?

How to Insulate Septic Tank Risers

Remove soil around the septic tank riser with the excavator.
Measure the circumference of the riser and cut the insulation to this measurement with a sharp knife.

Apply the adhesive to the insulation to the insulation and to the riser material.
Wrap the insulation around the riser.

How high should septic tank riser be?

Tank risers are typically installed about 3 inches above grade. Having the lid above grade will make it easy to find, however, some people will choose to have the lid just a couple of inches below grade so that is easier to mow over and less visible.

How much weight can a septic tank riser lid hold?

The 24-inch solid fiberglass DuraFiber riser lid from Orenco Systems has a flat-style lip for PVC and HDPE pipe. It weighs 10 pounds, but resists damage from lawn equipment and can withstand a 20,000-pound load.

How do you hide a septic tank riser?

The easiest way to hide your septic riser is by simply placing something over it, such as a hollow, lightweight landscape rock, a birdbath, a sundial or a decorative lawn ornament. Apply basic landscaping principles when deciding what to use.

What You Should Know About Septic Tank Risers

Septic tank risers are an important part of any septic system, and they should be installed in every property. This article will provide you an overview of septic tank risers and how they may help your septic system. What Is the Function of a Septic Tank Riser? A septic tank riser is a conduit that connects your home’s surface drainage system to your septic tank beneath the ground level. An access port or the pump-out ports on the septic tank are where the riser connects to the tank. Septic tank risers are equipped with lids that can be quickly removed to allow you to check or pump your septic tank without having to dig up your yard.

These structures are often made of materials that disintegrate slowly over time, such as plastic or concrete.

What Are the Advantages of Using Risers?

Normally, this entails digging up your yard before the pump is installed and reburying the tank once it has been installed.

The use of a septic tank riser can help to minimize the amount of time spent pumping your septic tank.
The fact that the riser is visible above the surface of your yard makes it an ideal signal for locating your septic tank the first time you need to discover one in your yard.
For those who want to stay in their house for several years, septic tank risers are not only handy, but they are also cost-effective.

Concrete risers are more durable, but they are also more expensive, and the price will be determined by the quote you receive from the contractor who will be installing them.
Because labor expenses account for a large amount of the fees that contractors charge for septic system inspection and pumping, installing a riser may possibly reduce the future cost of septic service by as much as 50 percent.
Each and every property can profit from the installation of a septic tank riser, but this does not imply that you should do so immediately.

This allows for the installation of the pump and riser to be completed in a single step.
Because a riser should be considered a long-term investment, you should make certain that your tank is in good working order before installing one.
A septic tank riser is a straightforward concept that can save you a significant amount of money and frustration when it comes to septic system maintenance and repair.

We look forward to hearing from you and answering any questions you may have about your septic system requirements. Contact us today. Please let us know how we can be of assistance to you and your septic system right now!

Septic Tanks Risers- Bring Your Access To Ground Level

Getting a little tired of having to dig up your yard every time your septic tank has to be pumped out or serviced? Are you getting tired of dealing with incredibly hefty concrete lids? It appears that you are in need of septic tank risers in order to bring your access down to ground level! Our septic tank risers and covers are constructed of high-quality, heavy-duty polyethylene plastic, which makes them extremely sturdy and durable while also being lightweight and simple to handle.

THE POLYLOK ADVANTAGE

Septic tank risers are available in a variety of shapes, sizes, and designs on the current market. We believe our Polylok septic tank risers are the best money can buy in terms of quality. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

Once the hole has been backfilled, the structural ribs in the Polylok septic tank risers are inserted inside around each riser piece, providing them with tremendous strength and allowing them to maintain their shape under the pressure of the earth being pressed on them. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

LIDS WITH HANDLES

The access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise maintained. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE ADAPTER RING

An adapter ring is required in order to properly install septic tank risers on your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

GET OUT YOUR MEASURING STICK!

A few measures must be taken before purchasing a septic tank riser system in order to ensure proper installation. The first thing to consider is the size of your opening. Take a measurement of the aperture in your septic tank at its widest point to determine the size of your tank. Instead than measuring the present lid, it’s critical to measure the opening. Because you will be removing the present cover, the measurements of the lid are no longer important and may differ from the size of the aperture itself.

The second measurement will be the distance between the top of the septic tank and the surface of the ground. You are now prepared to make a purchase based on these two measures!

THE COMPLETE RISER SYSTEM

We have a large selection of components from which you may pick to create your own own full riser system. Our many various options offer our product the adaptability to be utilized in virtually any application, but they may also be a bit daunting when attempting to pick which components to buy for a certain application. Each component is discussed in further depth below.

ADAPTER RINGS

The adapter ring is the first component that you’ll need to put together in order to assemble a full riser system. The adapter ring attaches directly to the septic tank, allowing the risers to stack, lock, and mount to it without the need for any additional hardware. Having this component is critical since the risers are not flat on the bottom because they are meant to be stackable, and it is not feasible to install them straight to the septic tank without this piece. The adapter ring provides the flat surface you need to mount to the tank while also being able to accommodate the stackable risers that are included with the tank.

Our square tank adapter ring can accommodate big square apertures up to 25 inches in diameter and large round openings up to 27 inches in diameter.

They are intended to be used with openings that are 24″ or less in diameter.

Concrete anchors, a masonry bit for installing the anchors, and butyl sealer are all included in this set.

RISERS

Following your selection of the adapter ring, it is time to go shopping for risers. The Polylok risers are available in two heights: 6″ and 12″, as well as in two diameters: 24″ and 20″. Stackable, each unit has a gasket that has been fitted as well as stainless steel screws to allow for easy installation. Determine which risers will work best for your application based on the height measurement you made between the septic tank and ground level.

OPTIONAL SAFETY SCREEN

In addition to the 20″ and 24″ riser systems, Polylok also produces safety screens that fit within the riser systems. These screens serve as a supplementary layer of protection in the event that the riser cover is unintentionally damaged or removed, and they keep foreign objects from entering the septic tank. They also keep dogs from slipping into unprotected septic tank openings!

RISER LIDS

You will require a lid to complete your riser system, which is the final component you will require. Both the 20″ and 24″ riser systems may be used with the Polylok lids, which are available in two different types to suit your needs. For ease of access, the basic lid is equipped with handles and a gasket that has been factory placed, as well as stainless steel screws to keep it in place. These lids are strong enough to withstand foot traffic as well as the weight of a riding lawn mower driving across them.

Stainless steel screws are included for installation.

Installations below grade or in regions with a high volume of foot traffic are advised for the heavy-duty lids.

The shipping of these items in large boxes necessitates the addition of additional time, materials, and UPS shipping fees.

SIMPLY ADD THE ITEMS TO YOUR SHOPPING CART AND THEN CHECK YOUR SHIPPING COST. If you place your order before 2 PM CST, you will be able to get your order sent the same day you placed it.

FREQUENTLY ASKED QUESTIONS

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered!

WILL THE LID FIT DIRECTLY ON THE ADAPTER RING OR DO I NEED TO USE A RISER?

With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength. The height of this reinforcement is actually more than the height of the adapter ring. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter. The lid will not fit through any aperture less than 24 inches in diameter.

CAN I CUT THE RISER SYSTEM DOWN TO A SPECIFIC HEIGHT?

No, the Polylok riser system is available in increments of 6″ and 12″, and it cannot be customized to a certain height. Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.

DO I BRING THE RISER SYSTEM JUST BELOW, AT, OR ABOVE GRADE?

It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade. Because the riser system is airtight and watertight, there is no danger in moving it up to or above grade level.

SHOULD I USE THE STANDARD OR THE HEAVY DUTY LID?

The regular lid is sturdy enough to withstand foot activity and weights up to the weight of a small riding lawn mower passing over it without bending or breaking. If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].

Installing Access Risers

In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below. Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.

A few safety tips before you get started:

Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website
Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.

Gather all the MaterialsTools You will Need

It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.

Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.

Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.

See below for Step 4 on attaching risers to the tank entrance. For the purpose of installing a riser system on your septic tank, you will require the following components:

Tank Adapter Ring (TAR)

Riser Adapter Ring Kit
Butyl Rope
Risers

Domed Lid OR Flat Lid
Stainless Steel Screws

The following materials will be required for digging up your septic tank(s):

As-built condition of the sewage treatment system The following items are required: sketch on paper, measuring tape, shovel, probing instrument, eye protection, and work gloves.

To cut risers to the proper size, the following tools are required:

Circular saws, saber/jig saws, and hand saws

Raspor file
Marking pen
Tape measure

Drill with a 1/4″ bit

Materials required to seal the risers to the tank include:

High-strength concrete patch mix

A small bucket
A mixing stick
And gloves

Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.

Step 1: LocateYour Septic Tank(s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.

Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.

The presence of underground electricity or other utility lines and cables might put your septic tank in danger.

Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.

Step 2: Uncover Your Septic Tank (s)

Once you’ve discovered your septic tank, you may start digging about. The tank is typically 6 feet wide by 8 feet long, with the width being the largest size. Remove all of the pebbles and debris from around the tank’s lid openings and dig out the whole top of the tank. You will want to clean out any dirt that has accumulated on the surface of your septic tank. This will assist you in ensuring that you generate a high-quality seal. You should have two openings: one over the inlet (which comes from the home) and another over the outlet (which comes from the yard) (into the drainfield or pump chamber).

You’ll need a riser for each of the doors you open.
Typically, the inlet side is the one that is nearest to the home.
When cleaning the tank, it is beneficial to remove the complete top of the tank.

Risers must be modified in order to be correctly installed, and all manholes (holes 24 inches or bigger in diameter or square in shape) must also be updated, as well as the tankinlet and outlet baffle covers (if separate from the manholes).
If you discover one – and only one – riser already installed, it is most likely for the pump chamber, which only requires a single riser to provide access to the pump to function properly.
Remove the concrete lids so that they may be disposed when the project is completed.

Consult your’As-built’Recorddrawing to establish whether you have a distribution box (D-box), which you will also need to unearth and place a riser on if you have a typical gravity system.
Once the lids have been removed, proceed with caution around the tank.
Inform someone of your whereabouts in case you are involved in an accident.

You should be aware that exposure to sewage can result in serious sickness, so make sure you wear gloves and thoroughly wash your hands afterward with soap and water. It is also recommended that you wear eye protection in the event that debris falls into a tank and splashes back at you.

Step 3: Fit Risers to Component Openings

In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:

Theriser will fit into the tank hole if the aperture is between 26 and 29 inches in diameter. Measure the distance from the ground to the top of the septic tank and multiply the measurement by three inches. The following is required if the aperture is greater than 29 inches: a 3-foot square fiberglass plate (with a 22-inch hole in the middle) is required. In this case, it lies above the manhole and narrows the aperture, allowing a 24-inch riser to be utilized instead of a more expensive 30-inch riser, saving money.

The distance between the ground and the top of the fiberglass plate should be measured. You may choose to place the risers so that they are level with the surface of the ground, or you may want them to stand out a few inches above the ground (if a riser is above ground make sure you are careful when mowing). Tips: To shorten a big riser with ribs, drill a 1/4-inch hole between the ribs above the cut line and finish the cut by following one of the grooves between the ribs with a saber/jig saw to finish the cut.

By eliminating one of the ribs from the largeriser, it may be made to fit more snugly into a smaller manhole entrance.

Step 4: Attach Risers toSeptic Tank (s)

It is recommended to pump out an old septic tank that is 20 years or older in order to check its structural integrity and water-tightness before using it again. If the tank requires extensive repairs, it is preferable to replace it with a new septic tank that includes risers as part of the installation. A permit from the local health department is required for the replacement of a septic tank. Remove any dirt and debris from the tank’s surface by cleaning it off. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s instructions.

Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names available.
NOTE: For optimal results, just a little amount of concrete patch should be mixed at a time.
The patch mix should be used to seal the riser to the septic tank.

If you want to avoid a safety danger, make sure you properly attach theriser lid using the screws that come with it!
Risers for inlet or outlet apertures that are smaller than the openings should have the bottom few inches sanded with rough sandpaper to allow a firmer connection between the two surfaces.
A useful source of information on correct installation of risers on septic tanks may be found at your local hardware store where you purchased the risers and covers.

Thurston County Environmental Health is should be commended for providing the foundation for this documentation.

Septic Tank Riser Installation

Tank risers are extensions of the tank lids that are already in place. They are installed in lieu of the current tank lids, bringing the septic tank’s access ports to, or slightly below, ground level in the process. Advantages of Using a Tank Riser

Riser tanks are expansions of the tank lids that are already in place on the tank. They are installed in place of the current tank lids, bringing the septic tank’s access ports to, or slightly below, ground level in most cases. Advantages of Using a Tank Riser.

Tank risers practically remove the need for excavating to expose the tank lids for pumping, which saves time and money. If the Alpha Omega is equipped with tank risers, it can readily pump the majority of tanks in less than an hour. In addition, in an emergency situation, the tank may be accessed swiftly and without interruption. Finally, because of the simplicity with which tank risers may be accessed, they encourage frequent maintenance. Alpha Omega suggests that two tank risers be installed on each septic tank, one on each lid, according to the manufacturer.

Regular septic tank lids, those do not reach up through the surface of the earth, are needed to be buried at least six inches below the surface to prevent gases from escaping.
We provide risers with a diameter of twenty-four inches to allow for the tank to be maintained correctly and thoroughly in the most effective manner possible.
They are made of a high-quality plastic that has been treated with UV protection.

Septic Tank Riser Kits – Wholesale Septic Supply

Are you fed up with having to dig up your septic system every time it has to be repaired or serviced? If this describes you, we have a fantastic option for you. In order to modify the way you operate on your septic system, you may require a suitable septic riser, which can be found online.

Why choose Tuf Tite Risers?

The Tuf Tite Septic Riser System allows you to get access to your outside septic system in a quick and simple manner. With the help of this revolutionary instrument, septic system service becomes a snap, and you will never have to dig up your septic system again! This system eliminates any guessing by providing you with the riser and other components you require to complete the task. Because you are ordering all of the essential parts in a single package, you will save both time and money on the installation process.

What are the Tuf Tite Product Specs?

Every riser system is simple to install on concrete septic tank lids, and the kit will even tell you what size access hole will work best with your septic system based on the information in the kit. The riser system is effective on 95 percent of septic systems with round diameter entrances ranging from 16 inches or less to 25 inches or less, and square sizes ranging from 11 inches by 11 inches to 18 inches by 18 inches. Looking for high-quality products? Look no further than this store! There are several sizes available for the Tuf Tite riser system, which has been engineered to last.

Septic tanks are normally installed below the surface of the earth.
Installing a riser kit is the most effective approach to deal with this issue.

When the riser comes into contact with the tank, an adapter ring should be used to seal the connection.
A number of risers will be stacked on top of each other and the adapter ring until they reach the ground level, at which point they will be removed.
This method will establish a barrier around the tank, protecting it from contamination while also making access to the tank more convenient.

In order to ensure that the circular riser will fit around your square or rectangular access port, there are a few things you may do.
The diagonal distance across the access will be the longest distance that a riser will have to cover before it may be used.
Assume that “a” is the length of one side of the port’s access.

For example, A is 12 inches in length and B is 12 inches in length.
The equations shown above can be used to estimate the diagonal distance of a rectangle in a rectangular coordinate system.
The only risers that should be utilized are those having an inner diameter that is bigger than the diagonal distance between the access port and the wall.

This approach will need the knowledge of the lengths of each side of your rectangular access port in order to work. Pythagorean theorem is something you may remember from your geometry training.

5 Reasons to Install Septic Tank Risers

Most homeowners consider their septic system to be a “out of sight, out of mind” service that receives little or no attention unless there is a problem. Septic systems are buried underground, and if you aren’t sure where your tank and its components are, it might be tough to discover your access ports or manhole covers if you aren’t familiar with your property’s layout. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings.

What is a septic tank riser and how does it work?
Risers, sometimes known as “extensions,” are available in a variety of heights to raise any access port up to grade.

Because the riser extends from your tank entrance to the lawn surface, it makes it much easier to reach your septic tank for pumping, maintenance, and inspections than it would otherwise be.
Digging down to your septic tank lid or access port and fitting the riser to the entrance are the steps involved in installation.
Then we’ll fill the area around the pipe with earth and put the lid on top of it once it’s in place.

The AdvantagesWhen it comes to septic tank risers, there are a plethora of advantages to consider.

The expense of installing a riser is one-time, but the advantages are long-lasting. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times
There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. This is in addition to the mess that it can create in your yard if the lid is buried several feet down

Nonetheless, it saves you money. Time is money, after all! Furthermore, since it is simpler to reach your septic tank, our staff can complete your task or resolve your problem much more quickly
It is critical to understand where everything is located. If you’re putting up a new patio, house addition, or backyard project, understanding where your tank and its components are located will be quite beneficial to your project. We’ll even draw you a schematic if you need one
Just let us know.

It is only necessary to install a riser once, yet the benefits will last for years to come. Once the extension is completed, you will not be required to pay for it again, and your tank will be easily accessible for pumping, maintenance, and inspections. Forget about looking for your access ports anymore. No more digging! When we bring your manhole cover up to code, it will be clearly visible at all times. This is especially useful during the winter months, when digging up a buried manhole cover can take several hours and need a lot of patience.

Timing is everything!

It’s quite helpful to know the exact location of your tank and its components if you’re planning a new patio, house addition, or backyard renovation. Even if you don’t want a diagram, we’ll make one for you;

Septic Tank Manhole Covers Ham Lake MN

It is critical to have your septic tank pumped on a regular basis in order to keep your septic system in good working order. Tanks should always be pumped through the manhole cover, not the inspection pipe, according to industry standards. Finding a hidden manhole cover in your Ham Lake, Minnesota yard may be a time-consuming and expensive endeavor. If your tank has to be pumped or if a problem occurs, a septic professional such as Custom Septic, Inc. may be required to excavate and dig up your yard in order to get access to the manhole cover.

Installing a Manhole Riser to lift the cover up to grade is a logical option.

You will save both time and money now that your septic manhole is easily accessible.

Install A Manhole Extension Riser

In order to maintain the health of your septic system, it’s critical that you get your septic tank pumped on a regular basis. Not the inspection pipe, but the manhole lid, should be used to pump out tanks at all times. In your Ham Lake, Minnesota yard, you may discover a sunken manhole cover that need repair. If your tank has to be pumped or if a problem occurs, a septic professional such as Custom Septic, Inc. may be required to excavate and dig up your yard in order to get to the manhole cover.

Installing a Manhole Riser to lift the lid up to grade is a practical option.

You’ll save both time and money now that your septic manhole is easily accessible!

Types Of Manhole Risers

It is a pipe or rings that are attached to the top of your existing septic tank and allow you to access it more easily. The manhole cover or lid is reinstalled on top of the manhole and will now sit flat against the earth. You want to ensure that the riser and manhole are completely covered and watertight. Manhole covers and risers are normally built of concrete, although they can also be made of plastic or metal, depending on the use. Risers are available in a number of sizes to provide a solid fit for your septic tank.

Clever Landscaping can also take care of any aesthetic difficulties that may arise.
Regular inspections and pumping of a septic system are required for proper system maintenance.

When having your septic system repaired, having easy access to the septic tank manhole cover might save you both time and money in the long run.
(CSI).
(CSI) is a fully licensed and insured company.

In addition to the Twin Cities metro region, we also serve Northern Minnesota. For a Free Estimate, call Brad at Custom Septic, Inc. (CSI) at 763-218-4769 or send him an email. Custom Septic Inc. (CSI) is a septic service company that covers the Twin Cities and Northern Minnesota.

Septic Tank Riser Kits

Prices include free delivery within the continental United States. Our Septic Tank Riser Kits are proudly made in the United States of America. Orders placed before 12 p.m. EST are dispatched the same day through UPS ground. Dimensions of the Septic Tank Riser – Click to enlarge. Watch this video to see how simple it is to install an Aero-Stream Septic Tank Riser! Parts and pieces that make up our Septic Tank Risers Features of our Septic Tank Risers are as follows:

Shipping inside the contiguous United States is included in the prices. Designed and manufactured entirely in the United States, our Septic Tank Riser Kits are second to none. If you place your order before 12pm, it will be dispatched the same day using UPS ground service. Please click here to view larger image of septic tank riser. Installing an Aero-Stream Septic Tank Riser is simple, as demonstrated in this video. Parts and pieces that make up our Septic Tank Risers. Characteristics of our Septic Tank Risers include:

Purchase the safest, highest-quality Septic Tank Riser available on the market! We’ve thrown in our Premium Low Profile lid at no extra charge. Coverage with a Low-Profile Finish

The low-profile lid raises the riser by only 0.5 inch. HDPE structural foam in a green color
Almost flush with the surrounding yard
Maintenance and mowing will be less difficult.

It takes only 0.5′′ to raise the lid from its low profile; a high-density polyethylene structural foam that is environmentally friendly. On a par with the rest of the yard, in fact; Maintenance and mowing will be less difficult to complete.

A safety barrier has been installed beneath the septic tank riser lid. Tank can be maintained without having to remove it. It is possible to remove it for servicing the baffles. Fits all shapes of holes, including round, square, rectangular, and other shapes
A patent application is pending. HDPE material that has been 100 percent recycled

A safety barrier has been installed beneath the septic tank riser lid; No need to remove the tank to service it. It is possible to remove the baffles for maintenance. Round, square, rectangular and other shaped holes can be accommodated. In the process of filing a patent. Recycled high-density polyethylene (HDPE).

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Contains a lid and a 7-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

MSRP: $248.0010′′ Septic Riser (MSRP $248.00) (AS-R10)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Includes a cover as well as a 10′′ riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

MSRP: $283.0013′′ Septic Riser (MSRP: $283.00) (AS-R13)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
The set includes a cover and a 13-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

Typical Retail Price: $312.0016-Inch Septic Riser (AS-R16)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Contains a lid and a 16-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

MSRP: $343.0019′′ Septic Riser (MSRP: $343.0019′′ Septic Riser) (AS-R19)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Includes a cover as well as a 19-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

Septic Riser with an MSRP of $365.0023′′ (AS-R23)

Septic Riser (MSRP: $365.0023′′) (AS-R23)

The MSRP for this item is $383.0026′′ Septic Riser (AS-R26)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Includes a cover as well as a 26-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

Septic Riser with an MSRP of $413.0029′′ (AS-R29)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Includes a cover as well as a 29-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

MSRP: $443.0032′′ Septic Riser (MSRP $443.0032′′ Septic Riser (AS-R32)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
The set includes a cover and a 32-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

enables maintenance to be performed more easily by elevating the tank entrance to the ground level With an inner diameter of 23-1/2 inches, the plastic adapter ring measures 30-1/4 by 30-1/4 inches. Covers all entrance forms, including round, square, and rectangular openings, amongst other things; Contains a lid as well as a 32-inch riser pipe Installation is straightforward, and the package includes all necessary hardware and sealants.

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
The set includes a cover and a 35-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

MSRP: $489.0038′′ Septic Riser (MSRP: $489.0038′′ Septic Riser) (AS-R38)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
The set includes a cover and a 38-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

Septic Riser with an MSRP of $513.0041′′ (AS-R41)

Septic Riser (MSRP: $513.0041′′) (AS-R41)

Septic Riser with an MSRP of $572.0044′′ (AS-R44)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Includes a cover as well as a 44-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MSRP of $595.0047′′ Septic Riser with an MS (AS-R47)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
The set includes a cover and a 47-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

MSRP: $619.0050′′ Septic Riser, MSRP: $619.00 (AS-R50)

Increases the height of the tank entrance above the ground level, making maintenance easier. The plastic adapter ring is 30-1/4′′ x 30-1/4′′ and has an inner diameter of 23-1/2′′. Covers all entrance forms, including round, square, and rectangular openings, among others
Includes a cover as well as a 50-inch riser pipe. Installation is straightforward, and the kit includes all necessary hardware and sealants.

The suggested retail price is $207.00.

You supply the pipe with an inner diameter ranging from 23.5′′ to 24.5′′
Fits ADS 24′′ (23-1/2′′) and old ADS 24′′ inside diameter double wall corrugated pipe
Plastic adapter ring measures 30-1/4′′ x 30-1/4′′ with an internal diameter of 22-1/2′′
It can accommodate openings of various forms, including round, square, and rectangular. Included are all of the necessary hardware, sealant, and an installation instructions.

The suggested retail price is $97.00. The Riser AdapterFlange for Septic Tanks with Safety Barrier

ADS 24′′ (23-1/2′′) inner diameter double wall corrugated pipe and old ADS 24′′ inside diameter double wall corrugated pipe are both compatible with four (4) stainless steel screws to attach the Adapter Flange/Safety Barrier to the Riser Ring. Plastic adapter ring measures 30-1/4′′ x 30-1/4′′ with an internal diameter of 22-1/2′′
It can accommodate openings of various forms, including round, square, and rectangular. Instructions for installation

MSRP: $102.0024′′ Premium Low Profile Septic Tank Riser Lid (MSRP: $102.0024′′ Premium Low Profile Septic Tank Riser Lid)

The lid has a low profile and is only 1/2 inch high. Inside diameter double wall corrugated pipe will suit both new ADS 24′′ (23.5′′) and old ADS 24′′ inside diameter double wall corrugated pipe HDPE structural foam in a green color
Three square drive bits are supplied, as is a rubber gasket. Almost flush with the surrounding yard
The mowing and upkeep are less complicated.

The suggested retail price is $207.0024′′.

A riser pipe connector for a septic tank that comes with a safety barrier kit.

Used with ribbed and smooth walled pipe with an ID of 24 inches
Inside diameter double wall corrugated pipe will suit both new ADS 24′′ (23.5′′) and old ADS 24′′ inside diameter double wall corrugated pipe current 24 inch riser is lengthened
Constructed of 24′′ ID plastic sewage tank riser pipe and connects it to an existing concrete or plastic septic tank riser HDPE material that has been 100 percent recycled
Four (4) stainless steel screws are supplied for attaching the flange to the riser pipe.

Used with ribbed and smooth walled pipe with an ID of 24′′; Inner diameter double wall corrugated pipe in ADS 24′′ (23.5′′) and old ADS 24′′ inside diameter double wall corrugated pipe is compatible. Riser is extended by 24 inches from its current position Adaptor for connecting 24′′ ID plastic septic tank riser pipe to an existing concrete or plastic septic tank riser pipe. Recycled high-density polyethylene (HDPE). Flanges are attached to riser pipes using four (4) stainless steel screws that are provided.

In addition to the Install Guide, you will need 14 1/2 feet of 3/4 inch x 1 inch Butyl Sealant Rope
Four (4) Tapcon Anchor Screws for attaching the Adapter Flange to the Septic Tank
And four (4) Stainless Steel Screws for attaching the adapter Flange to the Riser Ring.

Plastic Septic Tank Riser Pipe

In addition to the Installation Guide, you will need 14 1/2 feet of 3/4 inch x 1 inch Butyl Sealant Rope; four (4) Tapcon Anchor Screws for attaching the Adapter Flange to the Septic Tank; and four (4) Stainless Steel Screws for attaching the adapter Flange to the Riser Ring. In addition, you will need:

Install Guide
14-1/2′ of 3/4′′ x 1′′ Butyl Sealant Rope
Four (4) Tapcon Anchor Screws to attach Adapter Flange to Septic Tank
Four (4) Stainless Steel Screws to attach Adapter Flange to Riser Ring

The suggested retail price is $140.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $178.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

Double wall corrugated pipe with an inside diameter of 23 1/2 inches; NEW Safety Barrier incorporated.

Double wall corrugated pipe with an inside diameter of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $242.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $272.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $307.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $330.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $360.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $395.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $419.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $448.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $508.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

The suggested retail price is $531.00.

$531.00 (list price).

The suggested retail price is $555.00.

Double wall corrugated pipe with an ID of 23 1/2 inches
NEW Safety Barrier incorporated

How to Add to an Existing Septic Tank

The size of your septic tank is often determined by estimating the amount of water used by your property. It is possible, though, that you may need to upgrade your septic tank as you make changes to your property. To accommodate an additional bathroom, for example, modifications to your current septic system may be required. How to Install a New Septic Tank in an Existing Septic Tank Calum Redgrave is the photographer that captured this image. -close/iStock/GettyImages

What Is a Septic Tank?

A septic tank is a compartment beneath the earth through which effluent is channeled. The presence of a sufficiently big septic tank is vital for water safety. A septic tank that is too tiny will not be able to hold the wastewater in place. This retention is critical to the process of purifying the water in order to ensure that it may be safely dispersed into the surrounding earth. Smaller-than-expected septic tanks run the danger of blocking pipes and causing minor floods as well. If you’re planning major home modifications that will have an influence on your household’s water use, you’ll want to take your septic tank into consideration.

Septic Tank Usage When Adding a Bathroom

A septic tank is a chamber beneath the earth where wastewater is collected and disposed of. To ensure the safety of drinking water, a sufficiently big septic tank is required. Water cannot be contained in a septic tank that is not large enough. Keeping water in place is critical to the process of purifying it so that it may be safely discharged into the surrounding soil. The use of inadequately-sized septic tanks increases the likelihood that pipes will become clogged and that minor floods may occur.

If you’re planning major home modifications that will have an influence on your household’s water use, you’ll want to think about your septic tank as well. Additional septic tanks may be required in order to properly and efficiently treat your wastewater.

Adding a Septic Tank and Connecting to Existing Sewer Lines

The most straightforward method of increasing the capacity of your septic tank while keeping connected to current sewer lines is to simply add another septic tank. This increases the wastewater capacity of your house while also providing your septic system with extra time to process the wastewater before it is drained. For those who are planning to install an additional septic tank, first establish the best location, which should be between your existing tank and your drain field (sometimes called a septic field line).

A hole of appropriate size should be dug with an excavator.

Connect the two septic tanks together using a 4-inch pipe.

Insert the opposite end of the pipe into the outlet hole of your old septic tank once you’ve lowered your new septic tank to the ground.

Filling the hole surrounding your new septic tank with earth will then be an option for you.