How To Clean Out Thick Roots Of Septic Tank?

Take half a pound of rock salt and pour it into the toilet bowl. Flush as many times as needed until all the salt has flushed. Repeat the process until 2 pounds of salt has been flushed. Make sure to repeat the process frequently to clear the septic system off any roots!

What will dissolve roots in septic tank?

Flush 2 pounds of granular copper sulfate down the toilet for every 300 gallons of water that the septic tank holds. Copper sulfate kills and dissolves tree roots as they absorb the tank’s water. After entering a tank, the majority of copper sulfate settles in tank, and little passes into the leach bed line.

What will dissolve roots in sewer?

Copper Sulfate This bright blue salt-like crystal is available in most home improvement stores. Copper sulfate is a natural herbicide and will kill off the small tree roots invading your sewer pipes. Flushing half a cup of the crystals down the toilet should do the trick.

How do you kill roots in a septic tank?

There are special chemicals designed to kill tree roots in a septic tank system so they don’t grow back. Copper sulfate septic treatments are the most common. This method is especially effective as it creates a poison barrier within the soil that kills the tree roots before they can grow into the pipe.

How do you clean out a clogged septic tank line?

Tips for Clearing a Clogged Drain

1. Avoid cleaners with chemicals. Chemical-laden cleaners often break down the enzymes in your septic system, which are in place to help break down waste.
2. Pour hot water down the drain.
3. Use baking soda and vinegar.

What kills roots in drain field?

Copper sulfate can be injected into the drain field (past the tank) to kill roots.

Can you put root killer in septic tank?

Root Killer is non-corrosive and safe for all types of plumbing and will not harm surrounding trees, ground cover, or the natural bacteria content in septic tanks and cesspools.

Does foaming root killer work?

Fortunately, root problems can be controlled through the use of either Roebic K-77 Root Killer or Roebic Foaming Root Killer (FRK). You will need to choose the one that is right for your particular situation. Both of these products kill invading roots, but they will not “burn or “corrode” the roots out of the system.

Does Zep root killer work?

5.0 out of 5 stars Kills roots! Used this product for years after a company cleared my sewage line and stated roots were to blame. Works great, no back ups! I dump a whole container during the (late) FALL & SPRING down my sewage line.

How do you treat roots in a sewer line?

Try Copper Sulfate Copper Sulfate is also effective in killing roots in your sewer line pipes. You can get it at your local hardware store. Just pour about half a cup down the toilet and flush as many times as needed to wash it off. Leave the house for a few hours and take your kids and pets with you.

Does RootX dissolve roots?

RootX kills roots on contact and destroys the root structure within the first hour after application. The roots decay over time depending on the type of plant and the size of the root mass.

Is foaming root killer safe for septic systems?

RootX foaming tree root killer saves time and money when it is used to treat tree root intrusion in sewer drain pipes, septic systems, sewer systems and storm drains. Safe for all plumbing. The formulation foams on contact with water to kill roots and inhibit growth.

How long does Zep root Kill take to work?

It is important not to wait until a stoppage occurs because some water flow is necessary to move copper sulfate to the area of the root growth. Usually, within 3 to 4 weeks, after roots have accumulated sufficient copper sulfate, the roots will die and begin to decay and water flow should increase.

How do you get sludge out of a septic drain field?

Can Anything Unclog an Old Septic Drain Field?

1. Shock the System With Bacteria. A septic system bacteria packet can help clean out a clogged drain field by allowing waste material to break down and drain through.
2. Reduce Water Usage.
3. Avoid Harsh Chemicals.
4. Change to Gentler Toilet Paper and Soap.
5. Contact a Septic Professional.

How do I know if my septic line is clogged?

Stay vigilant for five signs your drainfield does not drain correctly anymore.

1. Slowing Drainage. Homeowners first notice slower than usual drainage from all the sinks, tubs, and toilets in a home when they have a compromised drainfield.
2. Rising Water.
3. Increasing Plant Growth.
4. Returning Flow.
5. Developing Odors.

Can I put muriatic acid in my septic tank?

You don’t want to put muriatic acid into your septic system or into a municipal sewage system. That means you need to add it to your toilet bowl when the water level in the bowl is minimal. If you add any extra, it will go down the drain line toward your septic tank.

Keeping Roots out of the Septic System

Aesthetically pleasing trees around your home can help to lower your energy bills by shading the roof and absorbing CO2. Nevertheless, the trees growing on your land are constantly on the lookout for moisture and nutrients, which their roots frequently discover within your septic system. Because of the thick structure of septic tanks, which makes them more resistant to root penetration, tree roots often gain access to the septic system by exploiting weak places in the sewage pipe that feeds the tank or the discharge pipe that leads to the drainage field.

Once roots identify a weak place in the sewage pipe, which is indicated by seepage, they are tenacious in their efforts to enter the pipe and take over the entire system.

When roots penetrate a sewer system, they most often cause sewage backups into the residence or clogs inside of the septic tank; however, there are other implications as well.

Preventive Strategies

When it comes to tree root issues, prevention is always the best medicine. It all starts with the choosing of the trees that will be planted on your land. Rapidly spreading roots are characteristic of fast-growing tree kinds such as willow, poplar, and birch, and these roots are extremely aggressive in their search for subterranean sources of moisture and nutrients. Local colleges and tree nurseries can recommend slow-growing alternatives that will flourish in your temperature zone and soil type while providing less of a hazard to your subterranean pipes.

If you don’t know where the pipes are, a plumber can identify their location and label it for you.

Create a supportive rooting environment immediately surrounding the tree by feeding and watering it on a regular basis at the location where you intend to plant it.

Maintenance

Another technique to prevent root invasions into septic systems is to do regular inspections and maintenance on the system. Roots are more likely to grow in sewer pipes that are more than a decade old, such as those made of concrete or clay. Seepage or leaks are the most common causes of root growth in sewer pipes. On the other hand, sewage pipes that are in good condition and do not leak moisture may withstand root penetration for an endless period of time. The sooner seepage or leaks from failing pipes are discovered and repaired, the less probable it is that roots will take advantage of this weakness and get access to your septic system and drain field.

A routine visual examination done by a plumber with the use of a fiber optic wire put into the pipe is, in the end, the most effective method of determining the condition of sewer pipes.

Chemical Treatments

Once little “feeder” roots, which are the first indicators of root infiltration, have been discovered during an examination by a plumber or if additional signs of root infiltration have been discovered, such as unexplained slow sewage flow, chemical treatments can be used to prevent further root development. It is possible to prevent little roots from developing into mature roots that can totally clog your septic system using commercially available root treatments that are prepared with copper sulfate and flushed into the septic system.

However, it seems likely that more direct intervention may be necessary in the future.

Mechanical Root Removal

A mechanical root cleaning instrument may be used to control root invasion in pipes in a direct and effective manner. The instrument, which is inserted through sewage access ports and into the pipe by a plumber, has a revolving auger with sharpened blades that tear off root accumulations that have accumulated inside the pipe. It is possible that subsequent root issues will be significantly postponed if regular follow-up treatments with root killing chemicals are continued after a mechanical clearing process has been completed.

Removal of fast-growing trees on the land is sometimes advised in order to reduce the problem of frequent root invasions.

Kill Roots In Your Septic Tank With A Root Removal Treatment

It is possible to successfully eliminate roots in septic tanks without harming the trees with RootX root killer. Using RootX root killer to get rid of hair-like roots in your septic tank is a vital, safe, and economical step in properly maintaining the health of your septic tank. In the event that you have trees in the vicinity of or surrounding your septic tank, there is a strong likelihood that you will have tree roots growing in your tank. Your septic tank or drain field may get clogged with tree roots, which can reduce or eliminate the leaching capacity of your septic system.

The septic tank is a watertight subterranean box that has historically been constructed of concrete, in which microorganisms decompose organic compounds contained in the waste stream.

Wastewater flows into the tank.

Using RootX to Eliminate Tree Roots in Septic Tank

Without harming the trees, RootX root killer is an efficient way to eliminate the roots in septic tanks. Removal of hair-like roots in your septic tank using RootX root killer is an important, safe, and economical precaution to ensure that your septic tank is functioning correctly. Having trees in or around your septic tank increases the likelihood that you will have tree roots growing in your septic tank. Your septic tank or drain field may get clogged with tree roots, which can reduce or eliminate the ability of your septic system to leach waste materials.

Bacterial digestion of organic components included in trash takes place in a waterproof subterranean box that is normally composed of concrete.

Clarified layer (sometimes referred to as clear water) is located between these two levels and is the only layer that should be directed to the leach field for final processing.

How to Clean Septic Tank Lateral Lines

Septic tanks allow residents to flush their wastewater without having to join to a citywide sewage system, which is beneficial in some cases. At any one moment, the majority of the wastewater is contained in two tanks. They use a natural settling mechanism to separate the solid waste from the water it is being used to clean. Long, horizontal and perforated pipes, known as lateral lines, are used to discharge the residual water into a drain field, which is a waste water treatment facility. Cleaning Septic Tank Lateral Lines: A Step-by-Step Guide Image courtesy of MemorioImage/iStock/Getty Images.

Lateral Lines in a Septic System

The lateral lines of a septic system allow the effluent water to trickle into an area that has been particularly constructed to filter and clean the water before it is released back into the groundwater supply. It is unlikely that the septic tank would suffer any difficulties with water outflow when the lateral lines, also known as field lines or leach lines, are correctly installed and operating. In some cases, however, sludge and paper products that are generally contained within the tanks might make their way into the lateral lines and cause drainage difficulties.

How to Clean Septic Tank Laterals

Septic systems may be accessible by homeowners or technicians through holes in the ground. A distribution box connects the lateral lines to the sludge tanks, which is where the sludge is collected. The box has a single input pipe on one side and numerous pipes – usually at least three – branching off on the other side or sides on the other side or sides of the box. The lateral lines are seen here. To flush these pipes, you can use one of a few of commonly available instruments. The first type of snake is that used by plumbers.

1. Plumber’s snakes can be operated by hand or by connecting them to a power drill for more power and speed.
2. The snake will open and release the blockage, allowing the materials to flow down the pipe when you flush the line later.
3. With high water pressure blasting through the debris, this flexible line is threaded into each of the septic tank laterals and then into the main tank.
4. The use of chemical cleaning agents is also an option, although in most cases, they do not yield substantial results.

When selecting chemical additions, exercise caution because they have the potential to pollute the environment and degrade the quality of groundwater.

Septic System Cleaning Limitations

One of the most difficult problems to deal with when it comes to clearing blocked septic tank field lines is the presence of tree roots in the pipe. When seeking for a place to grow, the roots will choose the path of least resistance, which means that the perforations and hollow interiors of the pipes will be great real estate for them. Although a water jet may be powerful enough to tear off thinner roots, the roots will almost certainly regrow. Heavy roots are insurmountable for plumber’s snakes or water jets to cut through.

It may be necessary to use chemical additives in order to destroy the roots and prevent them from regrowing.

Having the drain field correctly prepared in the first place is also beneficial in this situation.

Avoid needing to do a drain field cleanout by taking care during installation and keeping both the sludge tanks and the septic tank lateral lines in good working order on a consistent basis.

How to Clean Out Field Lines for a Septic Tank

DEBOVE SOPHIE is credited with this image. /iStock/GettyImages

In This Article

• Is It Possible to Save It?
• The Pressure Washer Approach Incorporating Biological Additives into Septic Tanks
• Installing an Aerator

If your septic system has begun to malfunction despite regular tank pumping and proper routine maintenance, it’s probable that your drain field has begun to malfunction. Sometimes a drain field problem may be repaired, while other times it cannot be repaired. Despite the fact that you can try to clear up your field lines in the hopes that a clog is the source of the problem, you may find yourself in the midst of a more significant situation. Professional evaluation of your system and recommendation of the best course of action is always a good idea.

• The first is that it is only intended to be used for a limited period of time.
• Following that, it’s normal for the drain field to require extensive repairs or maybe replacement entirely.
• As the waste accumulates, it hardens into a thick sludge that is nearly impenetrable by water, so impairing the capacity of the drain field to drain correctly.
• If you are experiencing any of these issues, cleaning up your drain pipes will not provide a solution.

If you suspect that your system is blocked or has just reached the end of its useful life, you may definitely attempt to clear out your pipes. At times, it is effective; at other times, it is not. You may prefer to hope for the best, but you should be prepared for the worst case scenario.

The Pressure Washer Approach

When it comes to cleaning up drain field pipes, a frequent method is to utilize a high-pressure water jet. Sewer jet devices, such as the Clog Hog, attach to a gas or electric power washer and then feed into the pipe, clearing away any obstructions or buildup. This particular cleaning process may be approached from two different perspectives. The recommended technique is to locate and expose the downhill end of the drain field pipes, after which you may feed the water jet backward via the drain field pipes.

If you choose to take this path, some sludge will come out of the pipe and into the distribution box, and you will need to remove it.

Biological Additives in Septic Tanks

Water from your septic tank has a high concentration of germs that break down solid debris. Most of the time, the bacteria in your septic tank is sufficient to complete the task at hand. In contrast, a rise in septic usage might lead the bacteria to “fall behind,” causing them to be unable to digest the waste at a fast enough rate. If you use some home cleansers or chemical drain openers, you can also destroy some of the microorganisms in your tank. If you’ve made a mistake and introduced harmful bacteria into your septic system or drain field, replacing them with an additional solution can help to rectify the situation.

1. Septic systems rely on beneficial microorganisms to aid in the digestion of the particles present in wastewater.
2. Aerobic septic systems provide oxygen to bacteria, allowing them to function more efficiently than other types of systems.
3. Addition of aeration after the fact is a possibility in the case of an anaerobic system.
4. The added bacteria may also aid in the digestion of any sludge that may be obstructing your drain field.

Rooting Out Tree Roots from Your Septic System

Taking Tree Roots Out of Your Septic System»Taking Tree Roots Out of Your Septic System

Rooting Out Tree Roots from Your Septic System

Trees enhance the visual appeal of a home and its surroundings in a variety of ways. However, this does not imply that they are without flaws in their design! Despite the fact that planting trees on your property has several advantages, trees planted near septic systems are a serious safety threat. Tree roots are constantly on the lookout for moisture and nutrients, and they frequently find their way into septic systems, which are abundant in both. However, even though septic tanks are typically sealed, tree root infestations can emerge through weak points such as fractures, fissures, and unprotected joints surrounding the sewage pipe feeding the tank or around a drainpipe that leads to a drainpipe.

Root incursions should be addressed as soon as feasible in order to help in drain unblocking and to allow water to flow freely through the drain system.

The measures outlined below can assist you in preventing the invasion of roots along sewage lines and keeping your septic system in peak operating condition.

Trust Good Ol’ Rock Salt

Before you attempt anything, put your faith in the ever-reliable rock salt to get the job done well. Rock salt, also known as sodium chloride, works as a toxin for plants and roots, preventing them from growing and thriving. The salt combination also serves as a highly efficient sponge, drawing moisture from the roots and preventing them from growing and flourishing. Pour half a pound of rock salt into the toilet bowl and flush it down the toilet. Repeat the process as many times as necessary until all of the salt has been flushed.

Make careful to repeat the operation on a regular basis to ensure that any roots are removed from the septic system!

Mechanical Root Removal

The use of a mechanical auger is one of the most frequent approaches for dealing with tree root infestations. The auger is similar in design to a reciprocating saw blade in that it has a spinning head coated with teeth made of steel. It is placed into the pipe by passing via the sewage access ports. The revolving head of the machine tears away the roots that have gathered in the pipe. Despite the fact that mechanical root removal is effective in eliminating root expansion, it is not a foolproof method because roots can regrow fast, rendering the effort pointless in the long term.

Chemical Root Removal

Chemical root removal therapy is a highly efficient method of destroying a root structure and preventing further growth. The procedure is flushing a copper sulfate solution available from a commercial source into the sewage tank. Using this mixture, which works as a poison barrier, you may destroy tree roots and prevent them from growing into sewer lines. The therapy is successful because it inhibits the development of tiny roots (which could lead to complete blockage of the septic system). Chemical treatment should be performed on a regular basis in order to keep tree root invasion under control.

Using Hydro Jetters

Hydro jetting is a more expensive option for eliminating tree roots from a septic system than other methods. Having said that, the force that hydro jetting generates makes it a highly effective method of flushing away undesired detritus and tree roots from a system. Pump and pressurized water are used to flush and clean the pipes, as well as to boost the system’s overall efficiency, in this high-pressure water system. Along with tree roots, it also eliminates oil, sand, dirt, and other buildup that can accumulate in drains and across sewage systems because to the frequency with which they occur.

Contact the Drain Unblocking Experts

Tree root outgrowth may be quite stubborn at times, making it nearly impossible to eradicate them completely. When this occurs, don’t hesitate to contact drain unblocking professionals as soon as possible to prevent your feeder roots from maturing and obstructing the entire septic system.

You can rely on the professionals at Streamline Environmental to assist you fish out the roots and unclog your drainage system so that it can resume normal operation. Make contact with Streamline Environmental immediately if you want septic assistance in the greater Hamilton region.

Roots in my Septic System

Tree roots are a major cause of septic system failure, according to the EPA. Let’s take a look at some scenarios in which roots will or will not have an impact on your septic system. The tank and the drain field are the two most important components of a traditional septic system, and both are susceptible to the dangers posed by tree roots: the tank and the drain field.

Septic Tank

Although tree roots can enter your tank through the access lid, they can also get in through the inlet or outlet pipes, or even through the seams of the tank. The access lid is the most vulnerable part of your tank to tree roots. The identification, cutting, and removal of roots may be accomplished during septic tank cleaning provided your system is properly maintained. When these little feeder roots are handled immediately, they are unlikely to become an issue that interferes with the system’s capacity to function.

If the larger roots are not managed, they might have negative consequences.

Septic Drain Field

Because of the perforated pipe, which is meant to allow liquids to seep into the drain field, roots can enter the drain field. However, even when roots reach a drain field, the system can still operate as long as the roots are not entirely choking the pipe. Although roto-rooter service can assist in clearing drain field pipes of roots, the results will only be temporary because the roots will regrow. In other cases, roto-rootering the drain field is not possible because the roots are too thick or because the roto-rooter is unable to reach all the pipes in the drain field.

However, because the entire extent of copper sulfate’s effects on trees and other plants is unclear, this can be a potentially hazardous activity.

If rules have changed since the original system was established, it may be necessary to install a whole new system.

As part of your septic tank cleaning, we will inspect your tank for roots at no additional expense.

We can assist you with any of your wastewater system needs, and our specialists can also assist you with your septic installation and maintenance requirements: 210.698.2000 (San Antonio) or 830.249.4000 (Austin) (Boerne).

Another reason to clean your tank: roots!

Posted on a regular basis There are several benefits to cleaning your septic tank, the most significant of which is to prevent sludge from entering your drainfield. Overgrown roots, which are frequently underestimated, may cause significant damage to a septic system if they are not properly monitored. Two massive mounds of roots were recently discovered in a tank and are displayed here for your viewing pleasure. Because they were so thick and heavy, it was difficult for our two technicians to even lift them!

• The seam of a lid is the most typical point of entry for roots.
• We’ve seen feeder roots via seams grow into 2″ thick roots within the tank as a result of the tank being neglected and not cleaned regularly.
• Occasionally, the roots get so thick and heavy that they are impossible to move.
• Roots have been known to make their way into the inlet baffle or pipe, resulting in a large blockage and a backup into your home at some point.
• If you keep an eye on the roots on your property, you can guarantee that they do not enter your tank and avoid any further troubles.
• Over the course of 80 years, Van Delden Wastewater Systems has proven itself to be the premier Wastewater System provider, supplying San Antonio, Boerne, and the surrounding Texas Hill Country with services you can rely on today and in the future.
• (Boerne).

Your Wastewater System: Having Root Problems?

Root issues may be extremely inconvenient and expensive to resolve. However, root issues may be managed by using either RoebicK-77 Root Killer or RoebicFoaming Root Killer, which are both available from Roebic (FRK). Ultimately, you will need to select the one that is most appropriate for your specific scenario. Invading roots will be killed by any of these chemicals, but they will not “burn” or “corrode” the roots out of the system like some other products do. In this bacterially rich environment, after the root has been destroyed, it will begin to deteriorate as a result of microbial activity.

In Septic Systems – If you have either a septic tank and a drainfield, or a cesspool and a seepage pit, and you are suffering root difficulties, you should consider using Roebic to treat the problem. Root Killer is a program that kills the roots of plants and trees.

K-77 Root Killer

K-77 Root Killer can be used as needed to eliminate problematic roots, hence restoring correct functioning order to the system’s operation. When used properly, this product has no negative impact on the environment, including adjacent trees, ground cover, or the natural microorganisms in the septic tank or cesspool. If, on the other hand, your system has no flow at all, you should have the system mechanically cleaned out before treating it with K-77 Root Killer. For the simple reason that if K-77 Root Killer cannot reach the roots, it will be unable to kill them.

• The length of time it takes is determined on the severity of your root problem as well as the location of the root problem inside the system.
• Some of you may find yourself in need of Foaming Root Killer.
• See the section below labeled “In Sewer Lines” for further information.
• If you answered yes, you may be dealing with a situation that might be very costly.

Foaming Root KillerRoebic Foaming Root Killer (FRK)

This one-of-a-kind root killer, which does not include copper sulfate, foams when it comes into contact with water, providing excellent results. This product also contains substances that aid in the speeding up of the decay process of the roots that it has been used to eliminate. This enables you to feel immediate alleviation from your underlying issues and challenges. (It should take anywhere from 2 days to 1 week for the Foaming Root Killer to completely clean your line.) Your system must have some flow in order for the Foaming Root Killer to function effectively.

Other Areas

Along sidewalks and driveways, cut a 3″ or deeper edging along the structure and apply Roebic Foaming Root Killer into the narrow strip to prevent root development from pushing up and injuring pavement structures. Annual application is recommended to reduce root development along the surface of sidewalks and roadways. BETWEEN ROOTS AND Sewage LINES: To prevent long-term root development from the tree to the sewer lines, a succession of tiny holes may be bored into the earth near or outside the sewer joints using either water or mechanical boring equipment, depending on the situation.

Inspect the hole to ensure that the depth and position of the hole are precisely between the troublesome tree and the sewage line.

RESTRICTIONS: Important Note: In Florida, root killers are not permitted to be used in SEPTIC SYSTEMS.

They are permitted for usage in MUNICIPAL SEWER LINES. The use of K-77 Root Killer is prohibited in the states of Connecticut and California’s Bay Counties, as well as the city of Golden in Jefferson County, Colorado. The K-77 FRK – EPA 7792-1 is the EPA 68464-1-7792 in the rear.

How to Keep Tree Roots Out of Your Septic System

Planting trees in your yard provides a number of advantages, including increased shade and visual appeal, among others. A tree that is placed too close to your septic system, on the other hand, might cause significant damage. It is critical for you to consider a number of variables before you begin planting new trees or constructing a new septic system on your property.

How do tree roots affect your septic system?

Water sources are attracted to tree roots by their natural attraction to water. They have the ability to “detect” regions of wetness, which is very useful near your septic system. Because the roots are unable to enter the tank itself, they direct their growth toward weak sections of the pipes. Roots grow into the pipes and eventually burst through, creating leaks, clogs, blockages, and long-lasting damage.

How can you keep tree roots out of your septic system?

The removal of tree roots, as well as the prevention of tree roots from becoming a problem in the first place, can be accomplished by a variety of approaches. When possible, it is always preferable to avoid prospective issues before they become a reality. It is recommended that, when designing or building a new home, the septic system be situated away from big clumps of trees. Whenever you are replacing trees, avoid planting them too close together and avoid planting trees with rapidly expanding roots (such as willow trees and birch trees).

• It is possible to have a plumber draw out the arrangement for you if you are unsure of the layout.
• If you acquired a property that already had trees near the septic system, but the roots had not yet reached their destination, you may be able to limit root development with certain chemical treatments before it becomes too late.
• If the roots have already made their way into your septic system, mechanical removal will almost certainly be required.
• A chemical treatment is then applied, which is quite successful in unclogging your drains and sewers.
• Trees and septic systems cannot continue to live in close proximity for an endless period of time.

Does routine maintenance matter?

Septic systems, like most other appliances and systems, require expert inspections on a regular basis to ensure that they are operating properly. Leaky pipes cause more moisture to be produced, which encourages tree roots to develop more quickly. Maintaining your vehicle on a regular basis helps to keep tiny problems from becoming huge difficulties. It saves you money while also keeping you safe from system failures altogether. Taking the time now to schedule an inspection might save you a lot of time and aggravation later on.

is a service-oriented company devoted to delivering exceptional septic tank cleaning and pumping services for both residents and business owners in the region.

We take great delight in finishing the task that others have left unfinished. If you have any more questions or would like to arrange a septic tank cleaning with one of our specialists, please contact us right away.

who should you call for septic issues?

Septic tank cleaning and septic tank pumping services are provided by Norway Septic Inc., a service-oriented company devoted to delivering outstanding septic tank cleaning and septic tank pumping services to households and business owners throughout the Michiana area. “We take great delight in finishing the task that others have left unfinished.” “They pump, we clean!” says our company’s motto. If you believe that your septic system is having troubles, or if you require septic replacement components such as septic filters, please contact us right once.

Our affiliate connections to these items generate a small profit for us if you decide to purchase them via our links.

What’s The Difference Between Septic Pumping And Septic Cleaning?

Septic tanks are a valuable asset, but they require regular maintenance to ensure that they continue to operate at peak performance and fulfill their intended functions. But if you’ve ever looked into septic tank care, you’ve definitely come across organizations that offer septic pumping and cleaning in addition to other septic related services. Despite the fact that these terms seem similar, they are not the same. Many businesses, on the other hand, fail to adequately explain the distinctions, as well as the benefits and applications of each.

Let’s have a look at this.

Septic pumping

Septic pumping is the process in which a sewage worker inserts a large hose into a septic tank to remove waste. This is accomplished by sucking up liquid as well as any sediments or sludge that may be floating on top of the tank with the hose. This not only frees up space, but it also prevents sludge from settling to the bottom of the tank, which might lead to worse problems in the future. It is advised that you get your septic tank pumped on a regular basis, such as every 1-3 years, to ensure that it is functioning properly.

In order to keep your tank running well for an extended length of time, sediment and sludge should be removed from the tank on a regular basis.

Septic Cleaning

With one important exception, septic cleaning and septic pumping are quite comparable services. Unlike septic pumping, which involves sucking out solids and sludges that have accumulated on the surface of the tank, septic cleaning involves draining the tank completely and cleaning up everything that has accumulated in the bottom of the tank. While many firms merely attach the hose and suck away the top layer of sludge, cleaning your tank is the best and most effective approach to ensure that it continues to function properly.

This implies that you should always search for a septic business that knows the distinction between pumping and cleaning, as well as one that provides a better level of customer care. There are a few crucial elements to consider when it comes to septic cleaning that you should be aware of.

Important Factors

When planning to have your septic tank cleaned by a professional, there are a few things you should be aware of that, over time, will assist you in keeping your septic system working smoothly.

Frequency

The regularity with which you get your tank cleaned will have a direct impact on how clean it becomes over time. It is quite easy to remove sediments and other waste things from your tank if you get your tank cleaned on a regular basis. The longer you wait, the more difficult it will be to remove waste since it will have solidified and will have attached itself to the walls of your septic tank walls.

Roots

In the course of time, large roots might infiltrate your tank and become entangled with the sludge. A typical vacuum hose will not be able to handle the roots since they are incredibly tough to extract. In the event that you have roots in your tank, even if you get it cleaned, roots and garbage will remain in the tank.

Dividing Walls

A separating wall is commonly found in septic tanks. In this case, your septic tank is likely to be divided into two portions. In order to ensure that both tanks are cleaned, it is necessary to specify this when scheduling a cleaning. It is critical to check the hose to ensure that it has been properly fitted into the access panel for both compartments once it has been installed. Because the dividing wall of your tank isn’t always watertight, a cleaner may place the hose on one side of the tank and suck out all the liquid while leaving sediments and sludge on the other side of the tank.

If you don’t, you might find up paying the whole fee for work that was only half done.

How Can Norway Septic Help?

Located in Norway, Indiana, Norway Septic Inc. is a customer-focused company devoted to delivering outstanding septic tank cleaning and septic tank pumping services to homes and business owners in the Michiana area. We take great delight in finishing the task that others have left unfinished. For more information on purchasing a new effluent filter or scheduling a septic tank cleaning with one of our specialists, please contact us right now.

How Do I Unclog a Septic Leach Field

Heavy particles can collect in septic field lines and clog perforations, causing the lines to fail to drain properly. The majority of septic systems that are more than 20 years old exhibit this characteristic. In certain cases, when an older septic system fails to drain properly, it is a symptom of tree roots obstructing the lines, problems with surrounding soils, structural damage to a pipe, or an improperly designed system.

1. A sewer jetter may be used to clean perforated PVC septic leach field lines with an ID ranging from 2″ to 6″

• With the use of a sewage jetter, you may scrape away sticky sludge and flush out unclean residue, which can help lessen the need for repeated cleaning of the lines. In addition, the Needle NoseTM drain cleaner has a stronger, braided steel jacket as well as a distinctive compact nozzle tip that allows it to pass through a wider range of drain types and sizes. A gaspressure washer with a flow rate of 2.0 GPM to 4.0 GPMis frequently necessary, because septic sludge can be difficult to scrape and flush out of the line without a lot of force. Electric pressure washers do not have enough force to clean and rinse away the thick muck
• Instead, they use water. In most cases, it is advisable to find and expose septic lines by digging a large enough hole under the downhill end of each septic line to allow sludge to run out and collect while you clean the opened line. Another option is to find and expose the distribution box, and then manually feed the sewer jetter through each of the lines that exit the box after it has been exposed. While it is possible to properly flush the sludge upward toward the opening box, it is more difficult, and you will need to pump out the heavy residue that runs back into the box. Starting at an uphill entrance or distribution box, the septic field lines should be allowed to drain or be pumped free of standing fluids so that they contain mostly biomat particles, because nozzle jets provide little cleaning and flushing action when fully submerged in liquid. For further information, please see this 3-minute video (which is a segment of Steve Maxwell’s do-it-yourselfSeptic System Rescuevideo course)
• Please keep in mind that a sewer jetter operated by your pressure washer will not be able to clean septic field lines constructed of flexible hose with an inside diameter of less than 2 inches, or septic fields made up of interlocking plastic chambers with an inside diameter of more than 6 inches. Important: If you suspect that there may be tree roots in the septic leach field lines, you should do the following: It is possible to loosen fine tree roots using a sewage jetter, and then pull out lengthy strings of roots by hand or with a leased motorized drum auger that is equipped with a root cutting blade if there are numerous fine tree roots. It is possible that you may need to start by renting a mechanical drum auger with a root cutting blade to loosen the tree roots, and then flush the line with a sewer jetter to eliminate any remaining septic sludge
• However, this is not always necessary.

• With the aid of a sewage jetter, you may scrape away sticky sludge and flush out unclean residue, therefore reducing the need for repeated cleaning of the lines. In addition, the Needle NoseTM drain cleaner has a stronger, braided steel jacket as well as a distinctive compact nozzle tip that allows it to pass through a wider variety of drain types and sizes. Because septic sludge may be difficult to scrub and flush out of the system, a gaspressure washer with a flow rate of 2.0 GPM to 4.0 GPMis frequently necessary. It is impossible to scrape and flush thick sludge with an electric pressure washer because of its insufficient force. In most cases, it is advisable to find and expose septic systems by excavating a large enough hole under the downhill end of each septic line to allow sludge to run out and collect while you clean the opened line. Other options include finding and opening the distribution box and manually feeding the sewage jetter through each line that comes out of the box. While it is possible to properly flush the sludge upward toward the opening box, it is more difficult, and you will have to pump out the heavy residue that runs back into the box. Starting at an uphill entrance or distribution box, the septic field lines should be allowed to drain or be pumped free of standing fluids so that they contain mostly biomat particles, because nozzle jets provide practically little cleaning and flushing action when completely submerged in liquid. Check out this three-minute video (which is part of Steve Maxwell’s do-it-yourselfSeptic System Rescuevideo course) for further information. Please keep in mind that a sewer jetter operated by your pressure washer will not be able to clean septic field lines constructed of flexible hose with an inside diameter of less than 2 inches, or septic fields made up of interlocking plastic chambers with an inside diameter of larger than 6 inches. The following information is critical if you suspect that tree roots may be growing in the septic leach field lines: It is possible to loosen fine tree roots using a sewage jetter, and then pull out lengthy strings of roots by hand or with a leased motorized drum auger that is equipped with a root cutting blade if there are several fine tree roots. The use of a rented mechanical drum auger with a root cutting blade to dislodge bigger tree roots and then flushing the line with a sewer jetter to eliminate septic sludge may be necessary in some cases if the tree roots are substantial.

• Put on a pair of work gloves that are resistant to fluids and eye protection. If you have reason to assume that the drain contains drain cleaning chemicals, proceed with caution. Hook up the drain cleaner to your trigger gun, turn on the pressure washer, and then direct the nozzle at least a foot into the exposed septic field line entrance before you begin to apply the water. As you push the trigger, make sure to guide the sewer jetter into the line. Every few feet, draw back approximately halfway and then continue pushing ahead
• This will provide a more complete cleaning. Immediately after you have done cleaning the pipe, remove the drain cleaner from the line. Use caution when releasing the trigger to prevent the water from flowing through the nozzle before it reaches the aperture. After that, repair any damaged fittings, inspect the system, and replenish the fill dirt.

• If you’re not confident in your ability to complete any of these tasks, hiring a septic service business may be a better option in the long run. To locate a service firm in your region, do the following:

• In order to get a recommendation for a firm that has performed comparable services for them, start by asking relatives, friends, and coworkers for recommendations. Search local directories such as Google Maps, Yelp, andCitySearch for service firms in your area that have received positive online reviews if you are unable to obtain a solid suggestion from someone you know. Don’t always believe reviews from persons who have written only a few previous reviews, or from those who exclusively provide favorable evaluations to everyone they interact with. You should be aware that even reputable service providers might receive a tiny percentage of unfavorable reviews for a variety of reasons that are not necessarily relevant to your situation. Choose an organization that has a large number of favorable, believable evaluations from customers who have had repairs identical to yours performed. After you have identified one or more service providers that appear to have a decent reputation, conduct an online search for the company’s name as well as the names of any persons who work for the company, if any. It is important to take into consideration both the positive and bad information you discover about the firm. Be aware that reputable service businesses may experience a backlog of several days at busy seasons, such as when temperatures are low, significant rain falls, or holidays fall on a weekend or holiday. In certain cases, high demand can be a symptom of a firm that has a large number of recurring clients

If you have any queries or comments, please do not hesitate to contact us.

How Can I Prevent Septic Root Problems?

Trees are something that we all like. This is especially true when they give us with refreshing shade on a hot summer day in Florida. Trees may also provide shade for your home, which can assist to reduce your energy use and expenditures. The fact that you are reading this text on our website most likely indicates that you have a septic system. Then there’s the possibility of an issue with tree roots. Trees are no different from any other plant with roots in that they seek for water and nutrients in order to flourish.

Septic tanks, with their thick walls and other protective measures, are extremely resistant to root penetration.

The tree targets any weak points in the system, such as the sewage pipe feeding the tank or the discharge pipes leading to the drainfield.

It will continue to work at the problem once it recognizes there is a water supply nearby, and given enough time, the tree will finally succeed. So, what can you do right now, and what may be required of you in the future? Let’s have a look at some specifics.

How Can I Prevent Septic Root Problems?

The following is required reading if you have just acquired or constructed a home and are uncertain of what you can do to avoid future difficulties. It is recommended that you exercise caution while selecting which sorts of trees to plant if there are no trees already in place on your property. Typically, trees with rapid growth have roots that are quite aggressive in nature. Not sure which trees would be the greatest choice? You may always speak with a local nursery, and they will be able to provide you with some options that may prove to be really beneficial in the future.

It is necessary for you to be aware of the location of your septic system.

Finally, after you have planted your trees, you may stimulate the growth of the trees’ roots close to the tree by watering and nourishing them.

What Maintenance Should I Do?

In order to eliminate root incursions into your septic system, you should examine and maintain your system on a regular basis. Roots are more likely to invade septic systems that are more than a decade old. This is due to the fact that they are the most prone to suffer seepage or leakage. Depending on how well your septic system is maintained and how often it is checked, you may never have any issues with tree roots at all. Some telltale indicators of leaky pipes in your septic system include brilliant green grass sections in your yard when the rest of your yard is brown, or soft moist places in your yard, as well as the stench of sewage in the air.

In Punta Gorda, for example, we can witness fast-moving roots from trees and bushes that are growing swiftly and aggressively in quest of water throughout the hot, dry months of the summer.

If you have not had a septic inspection lately and would like to make sure your septic system is in good working order give us a call or click here to request service.

Posts that are recommended

4 Ways Trees Can Negatively Affect Your Septic Drain Field

There are certain distinctions in care, usage, and budgeting that you should be aware of, whether you’re a new homeowner with an existing septic system or considering about purchasing or building a home without sewer hookups. This document outlines three ways in which your budget will be affected if your wastewater is treated using a septic system. 1. You will not be required to budget for municipal sewer service. Because the municipal wastewater system normally processes all of the water, the cost of city sewage service is sometimes determined by how much water you purchase from the city.

• A large number of homes with septic systems also rely on wells for fresh water rather than municipal water, which means you’ll likely save money in that department as well.
• It is necessary to include septic maintenance in your budget.
• Although you are not required to pay the city for the usage of your septic system, you will be responsible for the costs of maintenance if you want the system to continue to function properly.
• It is possible that these maintenance and repair expenditures will build up over time, so you may want to consider setting up an emergency fund to cover any unforeseen repair bills.
• You’ll also need to budget for the cost of a single inspection and begin saving for the cost of a tank pump.
• Spreading the expenditures out over several months is the most effective budgeting strategy, even for an expense such as tank pumping that does not occur every year, because it allows you to better estimate the costs ahead of time.
• You may need to set aside money for septic tank replacement.

The tank and leach field may not need to be replaced if you have a reasonably recent septic system and plan to sell your home within a few years.

If, on the other hand, your home’s septic system is more than a decade old, you’ll want to start looking into how much a new system would cost you as soon as possible.

For example, if the previous owners did not do routine maintenance or if the system was installed on clay soil, the system may need to be replaced.

It is a prudent decision to begin putting money aside in anticipation of this eventuality.

When you have a septic system, you may use these three strategies to budget differently.

Make an appointment with us right away if you’re searching for someone to pump out your septic tank or to complete an annual examination of your septic system. Our experts at C.E. Taylor and Son Inc. would be happy to assist you with any septic system assessment, maintenance, or repair needs.

Everything You Need To Know About Your Septic System

Florida people rely on roughly 2.6 million septic systems to dispose of waste and wastewater on a daily basis, accounting for 30% of the state’s population. Homes and businesses in rural regions rely on these systems to dispose of garbage in an efficient and environmentally friendly manner.

What Are Septic Tanks Made From?

Septic tanks are a waterproof box composed of concrete, fiberglass, or polyethylene material that is used to dispose of sewage. In other words, there will be no debris, dirt, or water from the surrounding ground that may get into the tank. Septic tanks made of concrete and/or fiberglass are the most common types.

Common Styles Of Septic Tanks

ATUs treat and filter waste by separating it into three compartments: a garbage compartment, an aeration chamber, and a clarification compartment. An aerobic, or thoroughly oxygenated, environment is created in the effluent by forcing compressed air through it. Because the bacteria thrive in this environment, waste decomposes more quickly than it would in a conventional septic tank. This helps to limit the quantity of organic material that enters the soil and groundwater around the house.

Double Compartment

Most tanks built since 1976 feature two compartments for filtering effluent, sediments, and wastewater that enters the tank during the construction process. The first compartment, which is placed adjacent to the intake pipe, is often bigger than the second compartment, which is located further away. It is possible to see the liquid flowing from the first container into the second compartment. Before the effluent is discharged into the outflow pipe, any remaining sludge and scum separate from the liquid.

Pump Tank

The quantity of wastewater that flows from the septic tank is controlled by a pump tank. Pump tank level increases as effluent accumulates in the tank and eventually reaches the level set by a control float. As soon as the float is activated, the pump starts pumping effluent into the drain field in a predefined volume.

Holding Tank

In lieu of septic tanks, holding tanks can be used to collect and store waste. They are either above or below ground and require constant pumping to remove the contents of their holding tanks. The majority of holding tanks are equipped with an alarm that sounds when the tank is full.

Single Compartment

A single compartment tank was utilized in the majority of septic systems constructed before to 1976. These tanks could hold up to 1,000 gallons of liquid at a time. After entering the tank and separating into three levels, liquid waste is discharged into the septic drain field via the outflow line.

What Is FOG?

Fats, oils, and grease (also known as FOG) are frequent cooking byproducts that occur naturally in a wide variety of foods and other items. While FOG is viscous when it first enters the septic tank, it cools swiftly as it comes into contact with the wastewater in the tank. However, because of its viscosity, FOG coats and covers every surface it comes into contact with when it solidifies.

How A Septic Tank Works

Solids sink to the bottom of the tank’s intake pipe, while FOG rises to the surface of the wastewater and collects at the top of the tank’s intake pipe. In most cases, the tank is large enough to keep wastewater for an extended period of time, allowing effulent separation to take place. There are three levels within the tank as a result of this separation: a sludge layer on the bottom, a wastewater layer in the middle, and a scum layer on top. bacteria, enzymes, and other microorganisms often present in human waste begin to break down the sludge layer and break down the sludge layer further.

Upon entry into the septic tank and drain field, two baffles direct and filter the water. The intake baffle prevents the scum layer from obstructing the inflow pipe, while the outflow baffle keeps scum and particles in the tank until they are removed by the drain.

What Are Septic Tank Solids?

The majority of solids contained in a septic tank may be divided into three categories:

• Non-biodegradable organic solids include pet litter, plastics, and other items that do not decompose over time
• Biodegradable organic solids include vegetable scraps and other cellulosic compounds, as well as toilet paper
• And biodegradable organic solids include solid human feces.

Septic System Drain Fields

After leaving the septic tank, effluent goes into a drain field, which is a network of underground pipes and dirt that collects the waste. Other phrases that are commonly used include absorption field, leach field, and trench. The size of the space required is determined by the following factors:

• Soil type
• Seasonal variations in groundwater level
• Amount of water absorbed each day
• And soil percolation rate are all factors to consider.

The soil percolation rate is defined as the amount of water that the soil can absorb in one minute per inch of soil thickness. A significant consideration in determining the site of a septic drain field in Florida is the percolation rate, which is crucial because the state has a high water table.

How A Drain Field Works

An underground network of perforated pipes may be found in this location, which can be found in either several trenches or a gravel-lined soil bed. Drainage from the pipes filters through the gravel and dirt before entering the sewer system. Compaction of the soil has a significant impact on its function, which is why it is critical not to construct structures on it or drive or park vehicles of any size over it.

Why Is A Drain Field Important?

Natural filtration is provided for effluent, which is recycled back into the groundwater source. It is possible that biological and chemical pollutants may infiltrate the water and create health problems for anybody who consumed or came into touch with the water without this filtering system in place.

How To Find Your Septic TankSeptic Drain Field

The location of the septic system will be shown on the majority of property plans and surveys. Possibly handed to you after the sale of your house or company, these documents are also maintained on file at the county government office. The septic tank is often built along the sewage line that leads away from the house or other structure. When this line is many inches in diameter, it means that it is located at the lowest level of your home, such as a basement or crawl space. Stick a metal probe every two feet along the sewage line as it exits the house, following it all the way out to the street.

Locate the borders of the septic tank lid with the probe – typically tanks are 5 feet by 8 feet in size, so this may take some time.

As soon as you discover a discrepancy between the system location and previously prepared diagrams or maps, make sure to update these materials and retain a duplicate for your records.

The Septic Tank Pumping Process

In order to prepare for extraction, the floating scum layer is first broken up by alternately sucking out liquid from the tank and pumping it back in to break up the bottom solid layer. Pumping is accomplished through the two access ports, which are referred to as manholes. The tank should never be pumped through the inspection apertures on the baffle wall.

This can not only cause damage to the baffles, but it can also result in insufficient waste removal from the tank. Until the septic tank is completely depleted, industrial vacuums are used to remove waste from the tank and into our tanker truck.

How Often A Septic Tank Should Be Pumped?

In most cases, every three to five years is sufficient. However, depending on the size of your septic tank and the amount of sediments and wastewater you produce on a daily basis, you may need to contact a septic tank pumping firm such as Jones PlumbingSeptic Tank Service sooner rather than later.

What To Expect During A Septic Tank Pumping

Before starting the pumping process, it is necessary to measure the thickness of the scum and sludge. This information is important in determining the pace at which waste accumulates and in determining when the next pumping should be scheduled. The pumping process is monitored closely by our personnel, who are actively monitoring for any possible system problems, such as backflow from the outflow pipe. Backflow that is significant typically indicates a backup in the drainfield, whereas slight backflow indicates a weaker outflow line in most cases.

Septic Tank Cleaning

Septic tank cleaning and septic tank pumping are not the same thing, despite the fact that many people use the phrases interchangeably. Pumping just removes liquid and uncompressed materials; cleaning, on the other hand, eliminates any leftover solids before washing the interior of the tank with soap and water. Following the removal of the liquid layer from the tank, our professionals employ pressured jets of water to break up any residual particles in the tank. Solids are removed from the tank with the use of an industrial-grade vacuum and a connected hose before the inside of the tank is washed.

This can result in the formation of sinkholes or the breakdown of the entire system.

How Often Should A Septic Tank Be Cleaned?

With every septic tank pump out, there is a new beginning. Keep in mind that the frequency with which the tank is pumped is determined by the number of people who are using the system and the volume of wastewater created on a daily basis. You may work with an aseptic tank pumping firm, such as Jones PlumbingSeptic Tank Service, to establish a regular pumping and cleaning program for your tank.

How To Keep A Septic Tank In Good Condition Between Cleanings

The most effective strategy to ensure that your septic tank remains in good working order for many years is to be informed of what can and cannot be put into the system.

Don’t DisposeFlush Items At-Will

In order to degrade materials that enter the tank, a septic system relies on bacteria that are found in nature. Although it is a mutually beneficial connection, it is susceptible to being pushed out of balance depending on the materials that are disposed of. Fat, oil, and grease (FOG); chemicals, paints, fuels, and/or motor oils; disposable diapers, sanitary, and personal hygiene products; coffee grounds; egg and nut shells; and disposable diapers, sanitary, and personal hygiene products are all common household items that should never be flushed down the toilet.

Schedule Annual Inspections

Home and business owners may do an outside inspection of their septic system on their own. However, only a professional and skilled septic tank firm, such as Jones PlumbingSeptic Tank Service, should check the tank and its interior components. Because of the formation of toxic vapors and gases within the sewage treatment plant, it is dangerous to work near one without the proper safety equipment and training. Look for areas of unusually tall grass, sewage odors or smells, and unexplained standing water as you walk around the area where the septic tank is situated.

PumpClean The Tank As Necessary

Skipping regular septic tank services is a surefire way to end yourself in a situation that might have been avoided. Performing routine pumping and cleaning allows our personnel to check the overall health of the system and correct any issues that may arise before they become a major concern.

Keep Records Of Septic LocationService

It is essential to understand the location of the entire system in order to properly maintain it. Parking or driving cars over any portion of the septic system should be avoided at all costs. The weight of vehicles can cause the system to collapse. When this occurs, the only option for repair is a complete replacement. It is also recommended by Jones PlumbingSeptic Tank Service that you preserve records of when the system was examined, pumped, and cleaned for your own records and in case you decide to sell your home in the future.

Conserve Water

The volume of water entering a septic system has a greater influence on the health of the system than the amount of solids created by the system. The greater the volume of water that flows through the drain field, the shorter the functional lifespan of the drain field and the overall system. An excessive amount of water flow impairs effective separation of particles inside the tank, increasing the likelihood of clogged intake and outflow pipes, which can result in sewage backups in the tank.

Septic Tank Repair In Gainesville, FL

Too much water in the septic tank increases the likelihood of sediments being transferred into the pipes, which might result in a clogged system.

Aggressive Tree Roots

Tree roots are well-known for generating problems with septic tanks and systems. Many species of tree roots are stronger than septic tanks, and they can cause leaks and other structural damage by cracking the pipes and tank.

Common Septic Tank Repairs

There are a variety of reasons why the pipes might fail, including compacted and/or moving soil. Once the pipes burst, they must be fixed as soon as possible to avoid significant drainage problems. When it comes to reaching and repairing the pipes, excavation of the area is frequently necessary.

Broken Baffles

The baffles of a septic tank are responsible for keeping sediments contained within the tank. Rust or contact with sulfuric acid are the most common causes of damage. It is quite beneficial to have an annual septic check performed in order to see if there are any difficulties with the baffles before a problem occurs.

How To Prevent A Septic Tank Failure

The fact is that septic systems are not foolproof and that they benefit immensely from routine maintenance and upkeep.

The majority of failures may be avoided by paying attention to what goes into the plumbing and septic lines.

Only Flush Toilet Paper

As a rule, toilet paper degrades and disintegrates more quickly than other types of paper goods. Particularly problematic are paper towels and wet wipes, which are two of the most prevalent causes of septic tank clogging and premature tank cleanouts.

Never Pour FOG Down The Drain

FOG is extremely harmful to all plumbing systems, including the septic system. FOG, when it is in liquid form, readily flows into the septic tank and collects in the top scum layer of the tank. This may not appear to be a problem, but the mixture has the potential to run into the drain field, where it might cause contamination concerns with groundwater and the surrounding soil if allowed to do so.

Regular Drain Cleaning

The numerous commercial drain cleaners available may temporarily unclog a clogged drain and associated plumbing, but they do so at the expense of the septic system’s ability to function properly. They include chemicals that swiftly eliminate the bacteria that are important for the decomposition of particles within the septic tank once they are applied. The layer of solids accumulates quickly — and needlessly — on the surface of the water. As an alternative, call a plumber to do expert drain cleaning.

How To Tell When You Need A New Septic System

A septic system may last anywhere from 20 to 40 years if it is maintained properly and repaired when needed on time. However, if you detect any of these frequent indicators of a failing septic system, it’s time to call Jones PlumbingSeptic Tank Service to have a new septic system installed in your home or commercial property. The following are common indicators that the present system should be replaced:

• Sinks and toilets that take a long time to drain
• Plumbing that is always backed up
• Sewage odors in the company, house, or yard
• Patchy mushy, swampy, or damp areas of the yard Gray water that has accumulated
• And grass that has grown more swiftly and is a darker shade of green

What To Know Before A Septic Tank Is Installed

In order to prevent the contamination of water sources and the creation of public health hazards that can result from incorrectly designed septic systems, the state of Florida and local municipalities have established rules and regulations to guide new septic system installations.

Required Applications, FeesPermits

The Environmental Health Service of the Florida Department of Health (FDOH) in Alachua County is responsible for issuing the necessary applications and permits. Before a permit may be issued, the house or business owner must submit a completed application, as well as a site plan, a building floor plan, and any applicable application costs to the local building department. A site evaluation is also necessary, which analyzes the overall condition of the land, as well as the soil type. Total fees are determined on the kind of septic system installed as well as the services provided by the county health division.

Minimum Tank Size

A minimum 900-gallon capacity is required for all septic tanks in Florida; however, this capacity requirement rises based on the size of the occupancy and whether the system is intended for residential or commercial usage. The specialists at Jones PlumbingSeptic Tank Service can assist you in determining the right tank size that complies with local and state specifications.

Landscaping Changes

Because septic systems are installed underground, it is probable that the existing landscaping will need to be removed and replaced. Our professionals, on the other hand, may propose that the new system be installed in a different place in order to minimize interference with plant and tree roots.

The Florida Department of Health mandates that the following distances be respected in order to prevent groundwater pollution from septic systems:

• If the property is located more than 75 feet from the annual flood line of a permanent, non-tidal surface water body or from the high water line of a tidal body of water, the following restrictions apply: 15 feet from a dry drainage ditch or stormwater retention area
• 10 feet from stormwater pipelines
• At least 200 feet away from public drinkable wells that are already in use for non-residential or residential structures with a total daily sewage discharge of more than 2,000 gallons
• And At least 11 feet away from any water storage tanks that come into touch with potable or groundwater
• A minimum of 15 feet away from a groundwater interceptor drain is required
• Minimum distances between bays, lakes and surface water
• Minimum distances between multi-family wells and/or private potable water wells
• And minimum distances between other wells.

New Home ConstructionSeptic Systems

Construction of new dwellings in rural locations or in any area that is not served by a municipal sewer system necessitates the installation of septic systems. Any system installed as part of a new house building project will have to take into consideration the elements and laws outlined above. In addition to establishing septic systems for countless new houses, Jones PlumbingSeptic Tank Service is happy to assist you through the application and permitting process, in addition to properly installing the system.