How To Check Outlet Pipe Septic Tank? (Solved)

• When checking the septic tank, both the inlet and outlet baffles should be evaluated, as well as where and how the piping enters and exits the tank. Inlet baffles need to be in place to direct flow into the tank downward to allow for settling of solids to occur and to prevent the “short-circuiting” of water and solids directly through the tank.

How do I find my septic tank outlet pipe?

The outlet pipe should be approximately 3 inches below the inlet pipe. Inlet Baffle: The inlet baffle is installed on the inlet pipe inside the tank.

How do you unclog a septic tank outlet?

Sprinkle the drain with baking soda, then dump vinegar into the pipe. Leave the mixture to sit in the pipe for an hour or two. Finally, flush the drain with hot water. If the clog is small, this could be enough to clear the pipe.

How do I know if my septic line is clogged?

Signs of Septic System Clogging: Water and sewage from toilets, drains and sinks backing up into your home. Bathtubs, showers, and sinks draining slowly. Gurgling sounds present in the plumbing system. Bad odors coming from the septic tank or drain field.

How deep should septic pipe be buried?

On average, trenches should be around 12-24 inches-deep, and wide enough to house your pipe comfortably before filling it in with soil and sod.

Why does my septic keep clogging?

A clogged septic tank or drain is caused by a number of things: An obstruction in the line caused by a buildup of pressure between the object and the inner circumference of the pipe. An example is a diaper stuck in the sewer drain line. There is simply too much diaper to fit through the line at once!

Why is my septic tank full again?

There may be several reasons why you have an overfilled septic tank. An overfilled septic tank is often a signal that your drain field is malfunctioning. The water flow backs up when your drain field floods, causing the water level in your septic tank to rise. Other common issues are plumbing and excess water use.

Will a flooded septic tank fix itself?

Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.

How do you tell if your drain field is failing?

If so, here are the eight signs of septic system failure.

1. Septic System Backup.
2. Slow Drains.
3. Gurgling Sounds.
4. Pool of Water or Dampness Near Drainfield.
5. Nasty Odors.
6. Unusual, Bright Green Grass Above Drainfield.
7. Blooms of Algae in Nearby Water.
8. High Levels of Coliform in Water Well.

How do you clean out a septic pipe?

Simple Cleaning Agent — White vinegar is a better option, providing a natural cleaning agent that can help keep septic drains free from mold growth and odor. It is recommended that you pour one cup of vinegar down the drains weekly and let it soak for about a half hour, then flush it through the system with water.

How do you tell if the leach field is clogged?

Stay vigilant for five signs your drainfield does not drain correctly anymore.

1. Slowing Drainage. Homeowners first notice slower than usual drainage from all the sinks, tubs, and toilets in a home when they have a compromised drainfield.
2. Rising Water.
3. Increasing Plant Growth.
4. Returning Flow.
5. Developing Odors.

Why the inlet pipe in the septic tank is higher than the outlet pipe?

Level the septic tank: The septic tank inlet tee is designed to be higher than the septic tank outlet tee. This helps assure that incoming sewage clears the baffle and enters the tank correctly, while outgoing effluent does not carry along floating solids, scum, or grease (which would clog the drainfield).

Can excessive rain cause septic problems?

It is common to have a septic back up after or even during a heavy rain. Significant rainfall can quickly flood the ground around the soil absorption area (drainfield) leaving it saturated, making it impossible for water to flow out of your septic system.

Everything You Need to Know About Your Septic Tank

What is a septic tank, and how does it work? A septic tank is a water-tight container that is often constructed of concrete, fiberglass, or polyethylene to prevent flooding (plastic). In fact, it is only one component of the entire septic system, which includes several other components such as a distribution box, pumps, float switches, aerators, filters, and other accessories. Septic systems are used to treat wastewater on-site in many rural and suburban areas that do not have access to centralized sewage systems.

The components of a conventional septic tank are depicted in the diagram below.

These are:

1. The Tank: This is the water-tight tank into which wastewater from your house is sent once it has been collected. A hole, fracture, or any other structural damage should not be present. Ports of Access: When a trained pumper comes to clean out your tank, he will utilize an access port. When it comes to tank cleaning, it is critical that the access port be large enough to allow the pumper to move the hose about within the tank properly. A common application for risers is to elevate septic tank access above ground level, eliminating the need to dig up your septic tank every time it has to be pumped. Last but not least, the access port should be securely secured with a child-resistant lid. It is vital for the protection of your family that septic tank lids are securely fastened with screws and bolts.

Any of the above-mentioned components in your septic tank should be checked for damage or missing parts as soon as possible, and the problem should be resolved by a septic system specialist. What is the operation of a septic tank? Each and every drop of wastewater from your home is channeled via a main drainage pipe and into your septic tank. Solids are prevented from entering your drain field by using the septic tank, which is just a settling tank that serves as a filter. Ideally, the water should be kept in the tank for at least one day in order to enable time for the solids to settle.

Heavy solids, such as dirt, are examples of this.

Tank Troubleshooting: Checking Inlet and Outlet Baffles

Receive articles, stories, and videos about septic tanks delivered directly to your email! Now is the time to sign up. Septic Tanks and More Receive Notifications When inspecting the septic tank, it is important to look at both the inlet and outflow baffles, as well as the location and manner in which the piping enters and exits the tank. In order to allow for the settling of solids in the tank and to avoid the “short-circuiting” of water and solids through the tank, inlet baffles must be installed to guide the flow into the tank downward.

Solids, on the other hand, can often block the effluent screen if the input baffle is not in place or not performing as it should, resulting in either backing up or overflowing.

This article is part of a series on troubleshooting septic tanks:

• Troubleshooting Techniques for Difficult Systems
• Septic Tanks: Troubleshooting and Repair
• Troubleshooting a tank includes inspecting the inlet and outlet baffles. Troubleshooting: Additional Items to Check in Septic Tanks That Are Having Problems

How to locate your septic tank and your drainfield

Septic systems on-site are used for accepting and treating wastewater in homes that are not linked to the municipal wastewater management system. A septic system is comprised of three components: a septic tank, a drain field, and piping. As a homeowner, it is your responsibility to properly operate and maintain your septic system in order to avoid system failure. For example, depending on the legislation in your area, you may be compelled to pump it on a regular basis.

It is impossible to perform maintenance operations, however, if you do not know where the tank is located. You can identify your septic tank by following a few simple procedures, which are outlined here.

Steps to follow to locate your septic tank and drain field

The contractor that designed and constructed the septic tank on your property should have submitted an as-built diagram with the local health authority before starting work on the project. In the event that you have the contractor’s contact information, you can ask them for a schematic, which you can then use to pinpoint the location of your septic tank. If you do not have a copy of the schematic, you can request one from the local authorities. Depending on whether the installed system included electrical components, the schematic may be available at the regional building department offices.

1. If you are unable to trace this diagram, you will need to do more research on the land in order to determine the location of the buried treasure.
2. This pipe is commonly found in the basement of a home, and it is a 4″ black pipe with a cleanout at the bottom.
3. Simply look for possible access coverings or a structure that might be concealing it.
4. These pumps are used to remove waste from the building.
5. It is supposed to be connected to the sewage output pipe.
6. As soon as you’ve discovered the sewer outlet in your basement, you may use it to figure out where the sewer line departs your home through an outside wall.
7. As a result, it is probable that the tank will be positioned around the corner from the building.

Tips for locating your septic tank

Septic tank lids should be visible from the outside. An underground riser may have been added, which will make it simple to find your septic tank in some instances. However, it is conceivable that the septic tank cover is buried underground, which is especially true for older homes. Following are some pointers to assist you in locating the septic tank in this and other similar situations.

• It may be possible to discover the septic tank lid underneath using a metal detector if it is buried. Prevent wearing footwear that contains steel or any other metal in order to avoid interfering with the readings of the detector
• Instead, you can use a flushable transmitter that is flushed down the toilet and then tracked with a receiver. When it comes to septic tanks, the strongest signal will be seen close to the intake region of the tank.

Depending on whether the septic tank is above or below ground, you may have to dig to get to it. Construction materials for septic tanks include concrete, fiberglass, or plastic, and their shapes can range from oblong to cylindrical to rectangular. The majority of modern septic tanks will have their lids positioned in the center of the tank, and the lid should be within three feet of the ground surface in most cases. However, depending on a variety of conditions, such as farming and other human activities on the property, it is conceivable that it will be significantly deeper.

Prevent being overly harsh with your shovel in order to avoid causing harm to the pipes. Additionally, you may use a small steel rod to probe the earth in order to pinpoint exactly where the tank is located as you continue digging.

Inspecting the tank

It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been identified. First and foremost, you may unscrew the lid to inspect the scum and sludge layer beneath it. In addition, the use of tracer dye tablets allows you to check the septic tank without having to dig it up. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of two days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field has a glowing green hue surrounding it.

It is possible that someone will fall into the tank, causing significant damage or possibly death.

Conclusion

You can identify your septic tank without assistance from a professional, but it is a good idea to have someone who is properly educated in septic tank maintenance examine and maintain your septic tank on your behalf. The effluent filter in your tank should be washed into the open septic tank rather than on the ground in your yard if your tank has one. It may also be a good idea to make a note of the position of the septic tank when it has been discovered. This will be beneficial to anyone else who may require access to the septic tank in the future.

Septic

Septic tank outlet pipe

I have a 30-year-old house with a single chamber 1000-gallon concrete septic tank and a traditional leach field that is in need of repair. We had the tank pumped when we purchased the property in 1990, but I let it sit for 7 or 8 years before pumping it again, which resulted in the need to rebuild the leach field. Maybe it was ready to go after 20+ years, or maybe I should have pumped it sooner.whatever the case, I’m currently in the middle of a three-year pumping cycle and consider it inexpensive insurance.

$$$$$ So I had the tank drained a couple of weeks ago, and the septic technician determined that the water level was excessive.

He had a feeling that was either a

Where is Septic Tank Outlet?

Author:Septic Tank Yank (CO)ruraldiy,We have a plugged up septic tank and want to put in a cleanout for the pipe to the field from the septic tank.If your septic tank is “plugged up”, installing a cleanout in the effluent pipeline will not solve your problem.The solution to a “plugged up” septic tank is to have the contents of the tank removed by a septic tank pumper.How deep from the top would I expect to find the output drain?If the tank is a manufactured precast concrete septic tank, the top of the effluent outlet pipeline should be 10 or 12 inches below the top of the tank wall.Typically, the tank outlet is on the opposite wall from the tank inlet.Before you install a cleanout in the effluent pipeline, think about how effective this cleanout will be in solving the problem causing the failure of your septic system.In my view there is no need for a cleanout in the effluent pipeline.If the leach field is totally clogged, cleaning the distribution pipes in the leach field will not cause the leach field to perform properly again.My advice to you is to consider modifying your system to the standards that are defined in the following response to an inquiry posted on the Plbg.com Discussion Forum by a fellow self-named “Dumbdad”.Author: Septic Tank YankDumbdad, sure sounds to me like the septic man is right. If you decide to have the leach field replaced, consider installing 2-half sized leach fields equipped with a 4-inch, NDS brand diversion valve. Cover the valve riser with a 10-inch round irrigation valve box to allow for easy access. The top of the box is set at the final grade elevation. The valve will allow the alternation of flow to the fields. Use half the field for 1-year while the other half rests. Turn the valve annually on the 4th of July, SEWAGE INDEPENDENCE DAY. Celebrate your independence of the sewer grid, and remember that with this independence comes the responsibility of a sewage treatment system operator.I recommend the use of plastic leach field chambers such as the ADS Bio-Diffuser, or Infiltrator brand. Cover each chamber leach field with a 4-foot wide sheet of geotextile fabric (landscaping fabric). The geotextile will prevent the migration of silt into the void under the chambers. The fabric also acts as a wick, wicking by capillary attraction, the effluent up over the chamber units and then into the soil.Install 4-inch monitoring and ventilation ports to the ground surface on each end of each field. The 4-PVC risers are covered with plastic 6-inch round irrigation valve boxes. The tops of the irrigation valve boxes are set at the final grade elevation. The boxes will allow easy location, easy access, and you can run the lawn mower right over them. Typically the covers of the boxes are green.The tops of the in-use field monitoring ports are fitted with 4-inch female threaded adapters, and threaded plugs to prevent sewer gas odors from emanating into the yard. The tops of the resting field ventilation ports are fitted with a 4-inch female adapters, and plastic drain grates.The ventilation ports will allow atmospheric oxygen to enter the leach field, and this will create an aerobic condition in the resting leach field. The oxygen will oxidize the Ferric sulfide (that black slimy crap), a major component of the clogging mat. Also, the aerobic condition will allow the aerobic microbes, present in the surrounding soil, to migrate to the clogging mat and consume the organic matter constituent of the clogging mat, and consume the dead bodies of all their anaerobic microbial cousins. Exchange the solid threaded plugs with the drain grates when the valve is turned on SEWAGE INDEPENDENCE DAY.While you are involved with the major renovation of your septic system, I recommend that 20-inch plastic risers be installed over the inlet manhole, and the outlet manhole of the septic tank. The covers of the risers should be at the final grade elevation to allow easy access to the tank. Let’s face it, if you must excavate the soil over the septic tank manhole with a shovel, chances are that this chore will be avoided. I use Tuf-Tite brand risers.I also recommend that the outlet tee of the tank be fitted with a septic tank effluent filter. The brand that I use is manufactured by SIM/TECH (the big bottlebrush type), although there are several other high quality filters on the market.The filter will reduce the organic matter in the effluent from flowing into the leach field. Clean the filter annually on SEWAGE INDEPENDENCE DAY.Another chore that should be performed annually is the measurement of the sludge accumulation in the primary chamber of the septic tank. The sludge can be measured with a “SLUDGE JUDGE.” Do an Internet search to obtain this neat device. I recommend the implementation of the “1/3 RULE” of sludge removal. When the level of the sludge is 1/3 the total liquid depth of the septic tank, it is time to remove it.The final chore to be performed on SEWAGE INDEPENDENCE DAY is to record all of the maintenance performed on the system in a maintenance log. I prepare a SEWERS CAN BE BEAUTIFUL operation manual for each of the septic systems that I install for my clients. The manual contains a description of the system design, photos of the system components, an as-built plan, a description of the required maintenance procedures, a copy of the permit, and the maintenance log. The manual becomes an excellent sales tool when the time comes to sell the home. The manual answers all questions a potential buyer may have regarding the performance of the septic system, and will allay the fears typically encountered when purchasing a home served by a septic system.Well Dumbdad, I had better end this lengthy diatribe. If all soil absorption type septic systems were designed and constructed to the above standards, then there would be far fewer failed septic systems. Maintenance is the key to successful septic systems. However, if the required maintenance is difficult, or impossible, then chances are it will not be performed. If you would like photos of my typical standard system, send me your e-mail address. My address [email protected] Aldrich (Septic Tank Yank)Septic System ConsultantTimnath, Colorado

How to Diagnose a Clogged Septic System

A blocked septic system can be caused by a clogged septic tank effluent filter, a clogged drain line leading to your septic tank, or a damaged outlet baffle, among other things. The first step in diagnosing a septic system backlog is to determine where the clog is located. Every year, millions of Americans rely on septic tanks to help them rid their houses of toxic biohazard products and wastewater that could otherwise be released into the environment. While a septic system is normally trouble-free as long as it receives periodic maintenance services, it is possible that a blockage will develop at some point.

Waste or debris that has built up over time is the most common cause of clogged drain lines or pipes, but it is crucial to inspect the whole septic system to make sure you haven’t missed anything else.

Steps to Troubleshoot Sewage BackupClogged Drains

However, while the issue is most frequently caused by garbage or material that has collected over time, having the ability to check out the system as a whole, your interior plumbing, and the external environment for more severe concerns is a smart idea.

1. You’ll want to look into the history of blockages in a specific spot in your house, such as a sink or a toilet, to see whether or not the pipe is connected to a bigger septic drain line so you can figure out where the backlog or smell is coming from. Make a flushable inventory of the following items: The fact that you cannot treat your septic system the same way you would treat a public sewer system is something that many people do not know or remember. Common home products such as “flushable wipes” and other non-septic tank compatible materials, such as paper towels, are difficult to break down and can clog pipes or cause blockages in septic tanks. They have the potential to do so over time.

Septic Emergency? Contact us immediately at570-828-7444

Additional Septic Services include the following:

• Repair of septic tanks, septic system maintenance, and septic system repair Replace a septic tank
• Conduct soil and percolation tests
• Provide a septic emergency response service.

Clogged Drain or Clogged Septic Tank?

Robs Septicon is the author of this piece. Postings under Uncategorised A blocked septic tank can cause difficulties that are quite similar to those caused by a clogged drain. Knowing the difference between the two might assist you in taking care of your house. Here’s all you need to know about the situation. When a septic tank overflows, why do drains become clogged? The septic tank is a holding tank that is located underground. All of the wastewater from the house flows into the septic tank, which steadily fills up with garbage over time.

Towards the top of the tank, there is a pipe that flows into the yard, into an area known as the drain field, where the tank is located.

SEPTIC PROBLEMS THAT CAN MIMIC DRAIN CLOGS

Your bathroom drains may be running slowly, and you may be thinking pouring some chemical drain cleaner down the drain to clear the clog. However, in these situations, rather than relying on potentially harmful drugs, it is always preferable to consult with medical specialists for a diagnosis. Instead of a simple clogged drain, you may be dealing with a plumbing vent problem, a sewer line problem, or a septic system problem instead. Learn about three septic issues that might manifest themselves in ways that are similar to drain obstructions.

A clogged baffleA normal septic tank has two baffles: one at the intake and one at the output.

The intake baffle assists in the smooth entry of wastewater into the tank.

3 THINGS TO KNOW ABOUT SEPTIC TANK BAFFLES

By Admin on November 12, 2020 Your efforts to live as environmentally conscious as possible, as a responsible homeowner, are likely already underway, with practices such as recycling, composting, and purchasing energy-efficient equipment among your list of accomplishments. As a septic tank owner, you want to be sure that anything you put into your tank and septic field is causing the least amount of ground contamination as is reasonably practicable. Fortunately, there are a number of modest improvements you can do immediately to make your septic system even more ecologically friendly than it already is.

Have your septic tank inspected and pumped on a regular basis. Septic systems and tanks come in a variety of sizes, and it is vital to understand the capacity of your septic tank as well as how frequently your tank should be pumped. As an illustration, if you have

How to Unclog Your Septic Tank

Documentation Download Documentation Download Documentation In the event that you have slow drains, pooling water in your yard, or foul aromas near your septic system, it is possible that one of the pipes has become clogged. Fortunately, there are several methods for removing blockages from your sewage system that do not require the services of a septic service specialist. To begin, search for any apparent obstructions inside your septic tank and try if you can drive them out with a little force.

Following the removal of the blockage, be sure to properly maintain the septic system in order to keep it clean!

1. 1 Check the inflow pipe by lifting the access cover of the tank that is nearest to your residence. The plastic or concrete cover in your yard that is closest to your house should be the first place you look. Carefully raise the cover of the tank up and away from the tank so that you can see what’s within. If you notice a white or green pipe at the end of the tank closest to your home, look for anything that could be blocking the pipe’s outlet. If there is, it is possible that the blockage is the source of the problem.

• Assuming the water level is below the level of the entrance pipe, the blockage might be located in the drain pipe that runs between the septic tank and your residence. If the water level is higher than the inlet but there is nothing blocking the end of the pipe, the clog is most likely in the leach field
• However, this is not always the case. It may be necessary to dig up the access lid with a shovel or raise it with a pry bar in order to get access.

If you are unable to locate the access lid for your septic system, consult your house’s as-built plans, which are blueprints prepared after your home is constructed, or a septic service if you are unable to locate the access lid for your septic system. 2 If the scum is trapped at the end of the input pipe, use a pole or a stick to push it out of the way. The scum layer is composed of solid waste that accumulates on the surface of the septic tank. Make use of a long, strong piece of wood or metal to slide the scum down or to the side of the entrance pipe as needed.

• If you are working in your septic tank, you should always wear gloves to prevent bacteria and waste from getting on your hands. If water starts to flow out of the pipe after you’ve pushed the scum out of the way, you’ve successfully eliminated the clog.

Advertisement number three If the blockage is deeper inside the pipe, use the pole or stick to probe the end of the pipe. Insert the end of the stick or pole you’re using as far as it will go into the end of the pipe you’re working with. Make use of the end of your probe to scrape the edges of the pipe and draw any waste from the pipe into the tank. Even if the clog is at the very end of the pipe, you should be able to dislodge it and get the water flowing once again. If water does not flow out of the pipe, the blockage is likely to be deeper within the pipe itself.

• Depending on where the pipe is located, you may or may not be able to insert your probe into the pipe.

4 Disinfect any instruments you used by mixing a 5:1 solution of water and bleach together. Stir up 1 part chlorine bleach and 5 parts clean water in a big bucket until the chlorine bleach is completely dissolved. Immerse your tools in the solution and allow them to soak for around 5 minutes to destroy any germs that may have remained on the surface. When you’re finished, drain the liquid back into your septic tank.

• If at all possible, take a shower or bath as soon as possible after working on your septic tank
• When you wash your garments, use bleach or laundry sanitizer to ensure that no bacteria is left on them after washing.

5 If you were able to resolve the issue, replace the access lid on the septic tank. Lift the lid and place it over the opening that leads into the septic tank to prevent it from closing. Slowly drop the lid down until it fully covers the hole and does not move around any more. In order to insert a mechanical auger into the clogged pipe if you haven’t already, leave the lid off.

• Never leave the septic tank door open while you aren’t working on it to prevent anything from falling into the tank.

6 Make use of a reputable service. If your tank was completely filled, you should pump it within 5 days. It is conceivable that your tank will back up again even after you have removed the clog. This is especially true if your main tank is completely full to the entrance line. Inform septic service personnel that the scum level has reached the pipe by contacting them through telephone or email.

It is best to schedule them within the following 5 days, otherwise you will increase the likelihood of septic fluid returning up the drainpipes. The service will completely drain your septic tank, preventing scum from re-entering the system.

• Having a septic tank pumped typically costs between $75 and $200 USD, depending on the size of the tank and the amount of waste that has to be removed. Every 3–5 years, or whenever the tank becomes full, have your septic tank cleaned and emptied.

1. In order to get to the inflow line, you must first remove the septic tank access lid that is closest to your residence. Because the intake pipe is more likely to be located on the access lid nearest to your home, if your septic tank has multiple access lids, select the one that is closest to your home. Using your hands, lift or pull the tank’s cover off and set it aside while you continue to work. Locate a white or green pipe that protrudes from the side of the tank that is closest to your house on the interior of the tank.

• If you are unsure about the location of your tank’s access lids, consult your home’s as-built plans or consult a professional service.

2 Using a mechanical auger, feed the cutting blade into the end of the obstructed pipe until it is fully engaged. A mechanical auger is comprised of a long metal cable that is inserted into your pipes and equipped with a revolving bit that cuts through the obstruction. Begin at the end of the blocked pipe or at an access point for the pipe, such as a cleanout port, to unclog the blockage. Placing the cutting blade of the auger inside the obstructed pipe and pushing the line in around 1–2 feet (30–61 cm) can clear the obstruction.

• It is possible to purchase a mechanical auger either online or from a local hardware shop. Investigate whether your local hardware shop provides equipment rentals to see if you can borrow an auger for the day without having to pay the whole price

3 Before you turn on the auger, make sure you have on your safety glasses and work gloves. Because mechanical augers feature spinning and moving elements, it is important to wear eye protection to avoid injuring yourself if you lose control of the machine while working. Wearing heavy-duty work gloves can help you prevent spreading germs and being harmed when handling the line. Ensure that the auger is plugged into an electrical outlet and that the switch is in either the On or Forward position.

• It’s possible that you’ll require an extension cord to connect the mechanical auger. You should never use the auger without wearing gloves or wearing safety eyewear since you might suffer a serious injury. Because the auger would spin violently if you start it with the cutting end outside of the pipe, you should never do so.

4 Continue to feed the auger farther into the pipe, allowing it to break apart the blockage as it goes. Holding the auger’s line with both hands, guide it into the pipe until you encounter resistance if necessary. Try turning the line in your hands to see how far it will travel inside the pipe if the resistance feels solid. It is possible that it has encountered a bend in the pipe. To drive the obstruction apart if this is not possible, use short, back and forth strokes to push and pull the auger.

• If you successfully clear the clog, water will begin to flow through the pipe again while you are still inside it with the auger. Mechanical augers are available in a variety of lengths, so if the one you’re currently using isn’t long enough to reach the blockage, consider renting the next largest size.

Tip: Always keep at least one hand on the auger’s line while it’s operating to ensure that it doesn’t spin or twist while you’re trying to feed it. 5 Before removing the auger from the pipe, be sure it is turned off. Make sure that the auger’s power switch is in the Off or Reverse position so that you can easily remove it from the ground. With both hands, gently guide the auger’s line back into the container, then slowly bring it back through the pipe to the other end. Using a hose or paper towel, carefully remove the auger’s end from the pipe and clear off any dirt or trash that has become lodged on the end of the auger’s end.

• It is not advisable to remove the auger from the pipe while it is still operating since it might cause injury. Remember not to touch the auger’s line with your bare hands because it has just passed through a pipe that contains garbage and potentially deadly bacteria.

6 The tools should be cleaned with a solution made up of 5 parts water and 1 part bleach. Stir the solution together by pouring 1 part chlorine bleach and 5 parts clean water into a bucket and mixing thoroughly. Clean the end of the auger with a cleaning rag to eliminate any germs that may have remained on the surface and avoid contaminating other parts of the machine. When you’re finished, drain the solution into your septic tank.

• Don’t flush the cleaning solution down the toilet since it contains bacteria from your septic tank that are dangerous.

7Remove the septic tank’s cover and replace it. Lift the lid off the ground by grabbing it by the handles or the sides of the container.

Lift and carefully drop the lid back onto the opening going into your sewage treatment system until it is completely enclosed. Make sure the lid does not slip or shift in any way, or otherwise it may break loose and fall off the septic tank. Advertisement

1. 1 Other than water and natural garbage, avoid dumping anything else down your drains. Water, human waste, and toilet paper are the only things that septic tanks are designed to handle
2. Thus, any additional products can cause the entire system to get clogged. To avoid clogging pipes, place paper towels, wet wipes, food scraps, and other solid waste in the ordinary garbage instead of in the recycling container. Inform other individuals in your home on what they may and cannot flush down the toilet in order to prevent clogging of the pipes.

• Using strong chemical cleansers down your drain is not recommended due to the possibility that they can destroy the natural bacteria in your septic tank that is responsible for decomposition of solid waste. You should never pour cooking oil down the drain because it might harden in the pipes and cause blockages that are difficult to clear.

As a reminder, you do not need to add any additional natural enzymes or bacteria to your septic tank in order for it to properly break down solid waste. Any enzymes that are introduced will be ineffective compared to the enzymes that naturally reside in the tank. 2 Reduce the amount of water you use in your home so that the septic system can drain correctly. Avoid running water in your home until absolutely necessary, since doing so may cause the tank to fill up too rapidly and overflow. Use as little water as possible when bathing or cleaning, so that you only have as much as is necessary at any one time.

• It will also save you money on your utility bills if you keep your water consumption to a minimum.

3 Avoid driving or planting over the area where your septic tank is located. Heavy weight can cause pipes going from your septic tank to collapse or break, so if at all possible, avoid driving over the region in a vehicle as much as possible. Plant roots can also grow into the pipes or septic tank, causing them to clog more quickly than they otherwise would. In order to prevent roots from growing within your septic system, you should put trees or plants at least 20–30 feet (6.1–9.1 meters) away from your sewage system.

• Even if you use a mechanical auger to cut the roots out of your pipes, the roots will grow back if the problem is not addressed. Root barriers purchased from gardening supply stores kill roots on contact and can help to prevent overgrowth in your septic system. To protect your septic system from pipes, dig a trench around it that is 2 feet (61 cm) deep and 3 feet (91 cm) away from them. Make sure that you place the root barrier in the trench vertically before you fill the trench back in with dirt.

4 Improve drainage by cleaning the effluent filter located on the outflow pipe. The effluent filter is a plastic cylinder that is installed in the exit line of your septic tank to prevent solid waste from escaping. Make sure the tank closest to your home has an access cover that can be opened. Look for a vertical white or green pipe that holds the filter and protrudes through the top layer of scum on the interior of the filter. Remove the filter from the vertical pipe by pulling it straight out and rinsing the waste back into the tank using a hose.

• Not every septic system will be equipped with an effluent filter
• However, most will. Check your filter every time you have your tank pumped or examined to ensure that it does not become clogged.

5. Have a professional inspection of your septic tank performed once every three years. Septic tanks typically take 3–5 years to fill, however this might vary based on the size of the tank and the quantity of water it receives. Consult with a professional provider to have the water levels and pipes for your system checked to determine if any adjustments are necessary. If the provider has any issues, you should solve them as quickly as possible to avoid having a malfunctioning septic system later on.

• Question What is the location of your septic tank? David Balkan is a writer who lives in New York City. A professional plumber and the CEO of Balkan Sewer and Water Main David Balkan is a licensed professional plumber who also serves as the CEO of Balkan Sewer and Water Main Service and the President of Balkan Sewer and Drain Cleaning, among other positions. With over 40 years of experience as an active owner of these businesses, David is well-versed in the challenges that arise with water service lines, sewers, and drain lines. David has served on the Executive Committee of the Sub Surface Plumbers Association of New York for more than 30 years and is now the Chairman of the Master Plumbers Council’s Committee on Plumbing. As a result of his expertise and solution-oriented approach, Balkan Sewer and Water Main Service has grown to become the biggest and most trusted sewer and water main service in New York City, and the recipient of the 2017 Angie’s List Super Service Award. CEO of Balkan Plumbers Inc. is a professional plumber.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

• Unless you are skilled in septic tank unclogging or there is significant damage to the pipes, you should hire a septic specialist to conduct the necessary repairs for you to guarantee that everything is in compliance with the law. When working on your septic tank, always use protective eyewear and disposable gloves to prevent contamination.

Advertisement

Things You’ll Need

• Hose
• Paper towel
• Mechanical auger
• Safety glasses
• Work gloves

About This Article

The writers of this page have together authored a page that has been read 315,299 times.

Did this article help you?