Septic Tank Installation Cost Materials cost between $600 and $2,500 without labor. A complete septic system, including a leach field, tank and piping costs $10,000 to $25,000. Installing a leach field costs $5,000 to $20,000, depending on the type. Materials cost between $600 and $2,500 without labor. A complete septic system, including a
Septic drain field – Wikipedia
, tank and piping costs $10,000 to $25,000. Installing a leach field costs $5,000 to $20,000, depending on the type.
How much does it cost to put in a well and septic system in Pennsylvania?
Cost To Put In Well and Septic System. A septic system costs $3,280 to $5,040 to install by itself on average. The cost to put in a well and septic system ranges from $6,000 to $20,000 depending on the type of septic system, type of absorption field, size of the septic tank, and depth of well drilling required.
What is the cheapest septic system to put in?
Conventional septic system These conventional septic systems are usually the most affordable, with an average cost of around $3,000.
How long do septic tanks last?
A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.
How big of a septic tank do I need?
The larger your home, the larger the septic tank you’re going to need. For instance, a house smaller than 1,500 square feet usually requires a 750 to 1,000-gallon tank. On the other hand, a bigger home of approximately 2,500 square feet will need a bigger tank, more than the 1,000-gallon range.
How much does it cost to pump a septic tank?
How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.
What are the alternatives to septic tanks?
Alternative Septic Systems
- Raised Bed (Mound) Septic Tank Systems. A raised bed drain field (sometimes called a mound) is just like what it sounds.
- Aerobic Treatment Systems (ATS) Aerobic systems are basically a small scale sewage treatment system.
- Waterless Systems.
What are the 3 types of septic systems?
Types of Septic Systems
- Septic Tank.
- Conventional System.
- Chamber System.
- Drip Distribution System.
- Aerobic Treatment Unit.
- Mound Systems.
- Recirculating Sand Filter System.
- Evapotranspiration System.
Do I have to replace my septic tank by 2020?
Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.
What is the most common cause of septic system failure?
Most septic systems fail because of inappropriate design or poor maintenance. Some soil-based systems (those with a drain field) are installed at sites with inadequate or inappropriate soils, excessive slopes, or high ground water tables.
What will ruin a septic system?
Any paper products like tissues, paper towels, tampons, or sanitary products, even some heavier toilet paper, will clog your system if you flush enough of it. Wet wipes are another product that you should never flush into a septic system.
Can you install your own septic system in PA?
All homeowners must obtain a permit from the PDEP before installing an aboveground or underground septic system. Operating permits are automatically renewed each year, and there are no fees associated with obtaining these permits.
How often does a 1000 gallon septic tank need to be pumped?
For example, a 1,000 gallon septic tank, which is used by two people, should be pumped every 5.9 years. If there are eight people using a 1,000-gallon septic tank, it should be pumped every year.
How deep is a septic tank usually buried?
Often, septic tank lids are at ground level. In most cases, they have buried anywhere from four inches to four feet underground. If you’ve just bought the home and you don’t know where your septic tank is located, this guide will provide information on how to find your septic tank.
Learn how much it costs to Install a Septic Tank.
Septic tanks range in price from $3,157 to $10,451, with an average cost of $6,804 per tank. Installation of a conventional 1,000-gallon tank for a three-bedroom home might cost anywhere from $2,100 and $5,000. Materials range in price from $600 to $2,500, without labor. A comprehensive septic system, which includes a leach field (also known as a drain field), tank, and plumbing, can cost between $10,000 and $25,000 to install. A leach field installation might cost anywhere from $5,000 to $20,000, depending on the kind.
In the end, the cost of installing a septic tank is determined by the kind of system, the materials used, and the size of the tank.
This course will teach you about the several sorts of settings, such as conventional, drip irrigation, mound irrigation, evapotranspiration, recirculating sand, constructed wetland, and chambered irrigation.
Septic System Cost Estimator
Let’s run some numbers to see what the costs are. What part of the world are you in? What part of the world are you in?
| National Average | $6,804 |
| Typical Range | $3,157 – $10,451 |
| Low End – High End | $450 – $21,000 |
Let’s run some numbers to see what it will cost. I’m curious as to where you are. I’m curious as to where you are.
New Septic System Cost
Allow us to compute some pricing information for you. What city are you in? What city are you in?
- Septic tank: Either anaerobic (requiring no oxygen) or aerobic (requiring oxygen but more complicated but more efficient)
- Water runs to a leach field after it has been cleaned and separated in the septic tank, where it will naturally drain through sand, gravel, and soil in a cleaning process before reaching the water table
- Water table: Plumbing: A drainpipe to the tank, followed by another branching pipe to your field will be required.
Optional components include the following:
- The following are optional components:
Find Local Septic Tank Installers
The installation of a traditional anaerobic system typically costs between $3,000 and $8,000 on average. Anaerobic systems are often less expensive to build than aerobic systems, which are more complicated. However, because they are less effective at cleaning the tank, you will need a bigger leach field to accommodate the increased burden. An anaerobic septic system is a very basic system that consists of a pipe that runs from the home to the tank and a branching pipe that runs from the tank to the drain field, among other components.
Aerobic Septic System Cost
Aerobic systems, which are those that require oxygen to work properly, cost on average between $10,000 and $20,000 per system. If you’re moving from anaerobic to aerobic fermentation, you’ll almost certainly need a second tank, but the conversion will only cost you $5,000 to $10,000. Aerobic systems break down waste more effectively in the tank than anaerobic systems, allowing you to use a smaller drain field in many cases – which is ideal for houses with limited space. An aerobic wastewater system is a wastewater system that depends on aerobic bacteria (bacteria that thrive in the presence of oxygen) to break down trash in the tank.
You’ll need an aerator as well as an electrical circuit that connects to the system to complete the setup. Small, mounded, or speciality fields may necessitate the addition of a dose or pump tank to assist in pushing effluent (sewage or wastewater) upward or out in batches.
Get Quotes From Local Septic Tank Pros
Beyond the tank and leach field, there will be a few more costs to consider when creating your budget for the project. You may already have some of these costs included in your total project pricing, so make sure to get line-item prices on your estimate.
- Excavation costs $1,200–$4,500
- Building permits cost $400–$2,000
- And a perc test costs $700–$1,300. Labor costs range from $1,500 to $4,000
- The cost of septic tank material ranges between $500 and $2,000.
- Plastic and polymer materials cost $500–$2,500
- Concrete costs $700–$2,000
- And fiberglass costs $1,200–$2,000.
- 500: $500–$900
- 750: $700–$1,200
- 1,000: $900–$1,500
- 1,200: $1,200–$1,600
- 1,500: $1,500–$2,500
- 2,000: $3,000–$4,000
- 3,000: $4,500–$6,000
- 5,000+: $7,500–$14,000
- 500: $500–$900
- 1,200: $1,200–$1,
Leach Field Cost
500: $500–$900; 750: $700–$1,200; 1,000: $900–$1,500; 1,200: $1,200–$1,600; 1,500: $1,500–$2,500; 2,000: $3,000–$4,000; 3,000: $4,500–$6,000; 5,000+: $7,500–$14,000; 1,000: $900–$1,500; 1,200: $1,200–$1,600; 5,000+: $7,500–$14,000; 500: $500
Alternative Septic Systems Cost
When you have a tiny property, a high water table, high bedrock, poor soil, or just wish to utilize less space, an alternate septic system is a good choice.
Mound Septic System Cost
Installing a mound septic system can cost between $10,000 and $20,000 dollars. In places with high water tables, thin soil depths, or shallow bedrock, this is the most costly system to build; yet, it is frequently required. In order to create a drain field, it uses a raised mound of sand rather than digging into the soil. Its extra cost is a result of both the additional technology required to pump sewage upward into the mound and the materials and labor required to construct the mound in the first place.
Recirculating Sand Filter Septic System Cost
Sand filter septic systems range in price from $7,500 to $18,500. They can be built above or below ground depending on the situation. In order to disperse the wastewater in the ground, they employ a pump chamber to force the wastewater through a sand filter. The liner of the filter box is normally made of PVC. This is accomplished by pumping the effluent through the sand and returning it to the pump tank, where it is then disseminated throughout the ground.
Drip Septic System Cost
Costs range from $7,000 to $18,000 for a sand filter septic system. They can be built above or below ground depending on the situation and resources available. In order to disperse the wastewater into the earth, they employ a pump chamber to drive the wastewater through a sand filter. In most cases, a PVC lining is used to line the filter box. As a result, it is pushed through the sand and returned to the pump tank, where it is subsequently disseminated over the earth.
Evapotranspiration System
Evapotranspiration systems range in price from $10,000 to $15,000 per system. In order to allow the liquid to evaporate from the top of an open-air tank, they employ a novel drain field configuration. They’re only usable in dry, arid areas with little rain or snow, thus they’re not recommended.
Built Wetland System
Built-in wetland systems range in price from $8,000 to $15,000, with the cost increasing if an aerobic tank is included. They are designed to simulate the natural cleaning process observed in wetland ecosystems. After traveling through a wetland tank, where it is treated by microorganisms, plants, and bacteria, it is returned to the soil. The waste also has the effect of assisting the growth of wetland plants and the population of microbes.
Chambered System
Installation of chambered systems ranges from $5,000 to $12,000 dollars.
They employ plastic perforated chambers surrounding pipes, which are frequently laid in sand, to keep them cool. Gravel is no longer required as a result of this. They are quick and simple to install, but they are more subject to crushing pressures, such as those caused by automobiles.
Septic Tank Replacement Cost
The cost of replacing a septic tank ranges from $3,000 to $10,000. From 30 to 40 years, you may anticipate your system to serve you well. The system may crack or corrode as a result of the failure and the resulting contamination of groundwater with toxic waste is an issue. When this occurs, the well water may get polluted, the yard may become marshy, and the septic system may become inoperable or fail completely. Here’s a breakdown of the various components of a septic tank, along with an estimate of their usual costs: Replacement of a septic tank pump costs between $800 and $1,400.
Replacement of the filter costs between $230 and $280.
Drain Field Replacement Cost: $7,500.
Septic System Maintenance Costs
It is essential that you pump and clean your septic tank at least once a year. In addition, you should get it examined at least once every three years. The proper maintenance of your septic tank will save you money in the long term, and it will also help you avoid potentially hazardous situations. The Environmental Protection Agency (EPA) suggests the following steps to keep your septic system in good working order:
Inspect and Pump Your Septic Frequently
Typically, the cost of septic tank pumping runs from $300 to $550, or around $0.30 per gallon – most septic tanks have capacities between 600 and 2,000 gallons. Every three to five years, you should have your septic tank inspected and pumped by a professional. If you have a bigger home (with more than three bedrooms) and you tend to use a lot of water, you should try to get it pumped at least once every three years. An checkup of a septic system might cost anything from $100 to $900. Your septic inspector will do a visual inspection of the system.
- Initial inspection costs between $250 and $500
- Annual inspection costs between $100 and $150
- And camera inspection costs between $250 and $900.
Use Household Water Efficiently
A toilet that leaks or runs continuously might waste as much as 200 gallons of water per day, although the average family consumes just 70 gallons of water. Take, for example, high-efficiency toilets, which consume 1.6 gallons or less of water every flush or less. The use of new, high-efficiency washing machines and showerheads can also help to reduce water waste, which will relieve the load on your septic system.
Properly Dispose of Your Waste
Your septic system is responsible for disposing of everything that goes down your drains and toilets. One easy rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless it is absolutely necessary. That implies you should never flush the following items down the toilet or drop them down the sink drain:
- Cooking grease or oil, baby wipes or wet wipes, dental floss, diapers, feminine hygiene products, cigarettes, cat litter, and paper towels are all examples of items that fall into this category.
Maintain Your Drainfield
The drainfield of your septic system is a component of the system that eliminates waste from the septic’s liquid.
You should take steps to keep it in good condition, such as:
- Never park or drive your vehicle on your drainfield. Don’t ever put trees near your drainage system. Maintaining a safe distance between your drainfield and roof drains, sump pumps, and other drainage equipment
Get in Touch With Septic Tank Installers Near You
A septic tank or septic pump tank can range in price from $350 to $14,000, depending on the material used and the size of the tank. In most home situations, you won’t have to spend more than $3,000 on the tank’s actual construction. The majority of big, high-priced units are intended for use in apartment buildings or as part of a communal sewage system.
Concrete Septic Tank Cost
Concrete tanks range in price from $700 to $2,000. The total cost of installation ranges from $2,300 to $6,500. They’re one of the most often seen forms of installation. Despite the fact that they are vulnerable to cracking and separation, they are often resilient for several decades. It’s critical to have it carefully inspected on a regular basis for cracks and runoff, among other things. Inspections and frequent cleanings will assist to extend its useful life. Your professional can tell you how frequently you should get it inspected, but it’s normally every one to three years.
Plastic and Poly Septic Tank Prices
Septic tanks made of plastic range in price from $500 to $2,500 on average, not counting installation costs. Plastic is a long-lasting, lightweight, and reasonably priced building material. They do not break as easily as concrete and do not rust. Because of their small weight, plastics are more susceptible to harm during the installation process.
Fiberglass Septic Tank Prices
Fiberglass septic tanks are typically priced between $1,200 and $2,000, not including installation. Fiberglass does not split or rust readily, but it is prone to damage during the installation process, much like plastic. However, because of its lighter weight, it is more prone to structural damage, and the tanks themselves can move in the soil.
Steel
It’s unlikely that you’ll ever see a new steel tank constructed. They will rust or corrode with time, no matter how well-made they are at the time. As a result, they are not permitted by many municipal construction rules, and you will only encounter them in existing installations. Steel is not a long-lasting material in the earth, and it is the least preferred.
Labor Costs to Install a Septic System
The cost of labor accounts for 50 percent to 70 percent of your overall expenses. Labor is typically more expensive than the tank itself in a normal installation, making it the most expensive option. For example, while the size required for a 3 to 4-bedroom home may cost between $600 and $1,100, the labor to install it might cost anywhere between $1,500 and $4,000.
Compare Quotes From Local Pros
Here is a breakdown of how much septic tanks cost in different parts of the country. Massachusetts:$9,700 California:$4,500 Florida:$5,300 Texas:$8,000 $5,600 in New York City Colorado:$7,800 Idaho:$10,000
DIY vs. Hire a Septic System Pro
The installation of a septic system is a time-consuming operation. An incorrectly fitted unit can result in water contamination, structural damage to the property, and the need for costly repairs.
In addition, an unpermitted installation might make it harder to sell and insure a property when it is completed. Make a point of interviewing at least three pros before making a final decision. Contact a septic tank installation in your area now for a free quote on your job.
FAQs
A septic tank has an average lifespan of 20 to 30 years, however it may live anywhere from 14 to 40 years, depending on the following factors:
- What it is made of is a mystery. Concrete tends to require more care, but commercial-grade fiberglass and plastic are known to survive for decades in most environments. It’s amazing how well you’ve kept it up. Every one to three years, have your system inspected and pumped out
- Every three to five years, have it pumped out. It will depend on whether or not it gets vehicle traffic over the leach field. Driving over the leach field compresses it, which increases the likelihood of it failing. The soil’s chemical makeup is important. The length of time it may endure varies depending on the soil type and depth.
What are the signs I need a new septic tank?
There are a few indicators that it is time to replace your septic tank. These are some examples: If you smell sewage, you may have a solid waste problem in your septic tank that has to be dealt with immediately. Standing water: If there is no clear explanation for standing water, such as a significant rainstorm, it is possible that you have an oversaturated drain field, a damaged pipe, or a faulty septic system. A clogged septic tank will cause pipes to drain more slowly than they would otherwise be.
Construction on your home or the addition of more occupants will have an impact on your septic system.
pollution of nearby water: A septic tank leak can result in wastewater contamination, which can deposit nitrate, nitrite, or coliform bacteria in water sources around your property as a result of the leak.
Old age: If your septic system has reached the end of its useful life, it is time to replace it.
Does homeowners insurance cover septic systems?
Many unforeseen and abrupt repairs to septic tanks are covered by homeowners’ insurance policies. They do not, however, often cover harm caused by a failure to perform routine maintenance. Make certain that you are pumping and cleaning it on a yearly basis.
How much do septic system repairs cost?
Repairing a septic system can cost anything from $600 to $3,000. Most tank repairs and replacement parts cost less than $1500 for each type of repair or replacement part mentioned below. Leach fields range in price from $2,000 to $20,000.
- Repairing a septic system might cost anywhere between $600 and $3,000. For each sort of repair or item described below, tank repairs typically cost less than $1,500. From $2,000 to $20,000, leach fields can be purchased.
Still Have Questions About Septic Tanks?
Septic systems on private land are used by approximately 26% of Pennsylvania houses for the treatment of domestic sewage. The majority of these residences also have their own private well for drinking water. If you have a septic system, be sure to operate it properly! If you understand how your system operates and how to maintain it, you will be able to do the following:
- Safeguard your drinking water supply and your health
- Maintain the longevity of your system—and prevent spending thousands of dollars on a new system
- Protect the value of your home
- And contribute to the protection of Pennsylvania’s groundwater, streams, rivers, and lakes.
Because of Pennsylvania’s geology, soils, land development patterns, and outdated septic systems, there is a danger that poor septic systems may contaminate our groundwater and surface waters—our streams, rivers, and lakes—as well as our groundwater and surface waters Surface waters that have been polluted with viruses and bacteria from sewage pose a greater risk of swimmers being ill with eye and ear infections, acute gastroenteritis, hepatitis, and other infectious disorders.
It is possible that groundwater contamination will poison your own and others’ drinking water supplies, resulting in the transmission of illness to humans and animals.
In 2020, the Pennsylvania Department of Environmental Protection stated that septic system failure was responsible for 202 impaired stream miles and 3,192 damaged lake acres in the state.
Septic system maintenance should be performed in accordance with industry standards to preserve your health, your money, and Pennsylvania’s waterways.
Who Has Oversight of Your Septic System?
In Pennsylvania, local governments (for example, boroughs and townships) are responsible for ensuring that private septic systems with a capacity of 10,000 gallons or less comply with Department of Environmental Protection (DEP) regulations. In the event that you have any queries regarding an existing septic system on your land, or about the construction of a new system on your property, you should contact your local government office first. Many towns have a Sewage Enforcement Officer who ensures that all septic systems are correctly sited, permitted, and inspected throughout their installation to verify that they follow all regulations.
Soil Is Your Best Friend: How Your Septic System Operates
Not only does your household transmit human waste into your septic system, but it also sends all other liquid wastes into it, including bath water, kitchen and bathroom sink water, laundry water, and water softener backwash. Consequently, here’s what occurs underground when you flush the toilet, wash your clothes, use the sink or bath: The heavier solid stuff descends to the bottom of the septic tank, where microorganisms feed on the waste and break it down as a result of their activity. Fatty oils and greases that are lighter in weight float to the top of the tank, where they congeal to create a scum that may ultimately break down or be skimmed off during system maintenance.
- Disease-causing bacteria and viruses are present in the wastewater as it exits the tank, in addition to other impurities.
- Sewage travels through a pipe to a drainfield, which is a bed of gravel or other material used to collect the waste.
- Therefore, soil is the most significant component of a septic system because of its filtering abilities and the bacteria that it contains!
- Several factors influence the sort of septic system that may be installed, including the soil depth to bedrock or groundwater, how fast or slowly water travels through soil, and soil type and texture, to mention a few.
Keep Things Moving Underground
It is believed that the typical lifespan of a septic system is between 15 and 40 years, although it may live much longer if it is properly maintained. Maintaining your septic system is similar to changing the oil in your automobile. It is a low-cost investment compared to the high cost of constructing a new system, which may cost up to $15,000 and more. Don’t overburden the commode with your thoughts when you’re at the sink.
Take into consideration what you flush down the toilet and down the sink. Reduce the amount of time you use your garbage disposal. It is best to avoid utilizing common household objects that might clog your system or kill the bacteria underground that are necessary for wastewater treatment.
- D diapers, baby wipes (including those labeled as “flushable”), cat litter, cigarettes, coffee grounds, fats and grease, solids (including feminine hygiene items), and prophylactic devices are all examples of “system cloggers.” “TreatmentKillers” include household chemicals, gasoline, oil, pesticides, antifreeze, paint, and excessive concentrations of anti-bacterial soaps and detergents, among other things.
Don’t put too much pressure on your drain. The less water that you use, the less work your septic system needs to do to keep up with you. Use water-based appliances in small batches, install high-efficiency plumbing fittings, and address any leaks that may exist in your house. Protect your playing field. Keep anything that weighs more than your lawnmower away from your drainage field. Rain and surface water should be diverted away from it. Root clogging in the drainfield might cause the system to fail, therefore avoid planting trees or shrubs in close proximity to the drainfield.
- It should be safeguarded and regularly inspected.
- According to Pennsylvania laws, this should be done whenever the tank is more than one-third full of solids or scum.
- Inspections and pumps may be required under the terms of your local sewage management program, which may be more strict.
- It is important to be aware of the following warning signals of a failing septic system:
- Backing up or bubbling of wastewater into residential drains
- There is an unpleasant smell, or there is some black sludge surrounding the septic tank or drainfield. In the vicinity of your drainfield, you may notice bright green vegetation or spongy conditions.
If your sewage system is not operating properly, contact your local Sewage Enforcement Officer right away. It is important to respond quickly since the less pollution that occurs, as well as the lower the expense of repair work, the better. Your septic system will serve your house and contribute to the protection of Pennsylvania’s waterways for many years to come if it is operated and maintained properly. Do your part and learn about septic systems!
Calculate septic system costs
Greetings, Angie: We’re seeking to acquire a new home, which will need the installation of a septic system. What is the approximate cost of purchasing and installing one? Washington, Illinois resident Robert S. wrote in to say Greetings, Robert: The cost of new construction – that is, a brand-new house with a brand-new septic system – will vary depending on the design of the system and the size of the house you are building. Septic tanks with a capacity of 1,000 gallons or more are required for most three- or four-bedroom homes, and the cost of the tank and installation ranges between $8,000 and $15,000.
- It costs between $3,000 and $7,000 to replace an old septic system, depending on the size and complexity of the operation.
- To dig out the system and drop the tank into the earth, you’ll need a lot of heavy equipment.
- The same time, there should be no other sort of traffic over a septic system before or after installation since soil compaction might prohibit the system from performing as intended.
- Following the installation of the tank, you may be left with many loads of earth that you may utilize in other parts of your property.
- For a new septic installation, you’ll need to get permits and inspections, as well as maybe conduct environmental testing.
- Experts in septic systems in your region should be aware of the requirements and the procedures for obtaining permits.
- New septic system installation can take anywhere from two to five days, but the time frame might vary significantly dependent on factors such as the county inspector’s schedule, weather and soil conditions.
Only hire a contractor that has received positive recommendations on a reputable consumer review site, has a substantial amount of experience building septic tanks, and who can show documentation demonstrating proper licensure, insurance, and bonding.
How Much Does a New Septic Tank System Cost?
On average, a new septic tank system will cost between $3,060 and $9,810, depending on the specifications. Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. Simply simply, trash is an unavoidable component of everyday existence. Septic tanks perform the dirty work for you, and they’re not particularly attractive. Anaerobic septic systems, which are the most common type, cost between $2,000 and $10,000. Aerobic systems are more expensive, ranging from $8,000 to $20,000.
How Much Does a New Septic Tank System Cost Near You?
Whether you’re building a vacation cottage or a year-round residence, you’ll need to take in the cost of a septic tank system into your budget. In general, the cost of a new septic tank system is $6,420 on the national level, while particular costs vary from state to state depending on a variety of criteria. As a starting point, each state has its own set of fees and regulations for obtaining construction permits and licenses. Before starting a septic tank project, be sure you understand the requirements in your region.
In general, sandy soil that is well-drained is the ideal choice for gardening.
Sewage tank installation prices can reach upwards of $9,000 in places where the soil is more saturated, such as clay, and where the state has severe septic tank licensing and permission regulations.
Outside of these locations, residents may anticipate septic system expenses to be in line with the national average.
Septic Tank System Cost Breakdown
The entire cost of installing a septic system will ultimately be determined by three factors: the materials and labor necessary to complete the installation, as well as the cost of digging a leach field on your land.
Materials
Concrete, fiberglass, and plastic are some of the most often used materials in septic tank systems. Concrete tanks are the most commonly used because of their longevity; with regular care, they may survive for up to 30 years or more. Concrete septic tanks typically cost between $700 and $2,000 on average. Plastic septic tanks are generally affordable, ranging in price from $500 to $2,500 per tank. On the other side, fiberglass tanks are more costly, ranging from $1,200 to $2,000 per tank.
Labor
It is possible that labor prices may vary by location and will be dependent on the size and materials used in the new septic tank system. However, in most cases, labor costs account for 50 percent to 70 percent of the overall cost of a septic tank system installation. Even though installation is more expensive than purchasing the tank alone, it is well worth it if you do not have the time or resources to undertake yet another home improvement project at this point in your life. Make certain that you and your contractor or plumber go over all of the specifics.
Additionally, construction permits, which normally cost between $400 and $2,000, and perc tests, which cost between $700 and $1,300 on average, are additional expenses that may or may not be included in your septic tank installation prices.
Leach Field
Leach fields, which are a type of trench, are used in conjunction with septic tank systems to collect and treat wastewater. It is the component of your septic system that returns the wastewater to the earth, often known as a leach field or drain field. Leach fields range in price from $2,000 to $10,000. Photo courtesy of Natalia / Adobe Stock
How Much Does a New Septic Tank System Cost by Type?
Each form of septic system has its own set of advantages and disadvantages. Even though anaerobic systems need less maintenance, they are not suitable for use on smaller parcels of land. Anaerobic systems, on the other hand, may function effectively in compact places but need additional effort.
Anaerobic
Septic tanks can be classified as either anaerobic (requiring no oxygen) or aerobic (requiring oxygen). Anaerobic systems, which are more frequent, cost between $3,000 and $8,000 on average, according to the manufacturer. They are often less expensive to install than aerobic systems, but they are less efficient and need a bigger leach field than aerobic systems. In an anaerobic septic system, a pipe connects the home to the septic tank, and another pipe connects the septic tank to the leach field, where the waste is disposed.
This type of system does not require any additional electricity or chemicals, which makes it a popular choice among homeowners.
Aerobic
Aerobic septic systems make use of oxygen that is fed into the tank to activate bacteria that feed on the solid waste in the tank. These systems are more expensive than anaerobic systems, costing between $10,000 and $20,000, but they are more efficient and may be used effectively on smaller sites. In contrast to anaerobic systems, they require more electricity to function well. Connecting it to a backup power generator will guarantee that everything continues to function correctly in the event of a power loss.
How Much Does a New Septic Tank Cost by Style?
The size and location of your property will play a role in determining which type of septic tank system is best for your needs. The mound or sand filter aerobic septic tank systems are recommended for smaller properties, while those with greater room have a wider range of alternatives.
Mound
Expect to spend more money if you choose a mound septic system, which may cost between $10,000 and $20,000 to install. A sand mound is constructed on top of the septic system region to collect wastewater that has been pumped out of the tank. Water is filtered via the sand before it enters the soil and groundwater. Even though these systems are costly, they are important in locations where the water table is high.
Sand Filter
Sand filter septic systems employ a pump to force wastewater through a sand filter at a low pressure before it is released into the soil or groundwater, effectively treating and removing nutrients from the wastewater. Despite the fact that nutrients such as phosphorus and nitrogen are naturally found in trash, when they collect in surface water, they can degrade water quality and cause aquatic ecosystem harm. They range in price from $7,000 to $18,000 and may be constructed either above or below ground.
These systems are most effective in locations with high water tables or in areas where there are bodies of water nearby.
Chamber
Chamber septic systems are identical to conventional systems, except that they employ plastic chambers in the leach field instead of gravel to collect the waste. They range in price from $5,000 to $12,000 to install. Chamber septic systems are excellent solutions for sites with varying input quantities, such as vacation homes or rental properties. You should avoid placing it near your driveway or parking area if you choose this type since driving over it might cause considerable (and stinky) harm.
Drip
Comparable in design to conventional systems, chamber septic systems employ polyethylene chambers instead of gravel in the leach field. Depending on the model, installation costs between $5,000 and $12,000. When it comes to vacation houses, chamber septic systems are an excellent solution because the input quantities fluctuate. You should avoid placing it near your driveway or parking area if you choose this design since driving over it might cause considerable (and stinky) harm.
Evapotranspiration
Evapotranspiration septic systems range in price from $10,000 to $15,000 and are particularly beneficial in dry regions and locations with thin soil. They have special leach fields that allow wastewater to evaporate from the top of an open-air tank, which is not common in other tanks. If you reside in an area where there is a potential of snow or rain, an evapotranspiration septic system should be avoided at all costs. The dampness might eventually cause them to collapse, and the repair process for a septic tank is not particularly attractive.
Built Wetland
As you may have guessed, constructed wetland septic systems are designed to replicate the natural water treatment process found in wetlands. Water is treated in a wetland tank by microbes, plants, and bacteria before being released back into the environment. As a result, the waste promotes the growth of plants and bacteria. The cost of these environmentally friendly systems ranges from $5,000 to $12,000.
What Factors Influence the Cost of a New Septic Tank System?
Several factors influence the cost of a septic tank installation project. In general, costs rise as the size of the organization grows. If landscaping and permits are necessary for the installation of your septic tank, you should budget an extra $600 at the very least. The sort of material you choose will also have an impact on the price, with plastic being very inexpensive when compared to concrete. Furthermore, if you choose a more customized design over a stock model, you will be responsible for the additional work costs.
As a result, the amount you pay will be determined by the location of your home as well as the soil type that surrounds your property.
FAQs About Septic Tank Systems
A septic system that has been poorly built can cause serious difficulties, such as water contamination and structural damage to your property. Repairs to a septic system are not inexpensive.
Because of the high level of danger involved in constructing septic tanks, this process should be left to the professionals. Call around and talk about your requirements (as well as your budget) with a number of septic tank businesses in your region to find the ideal match.
What should I consider when installing a septic tank system?
A septic tank is an essential component of every property. Damage to your property as a result of structural failure or leaks may be costly, as well as dangerous to human and environmental health. It’s possible that the unpleasantness will even compel you to check into a motel for the night. Prior to establishing your septic tank system, take the following factors into consideration:
- Soil type
- Landscaping
- Structural hazards (avoid places near cars or heavy machinery)
- The size of the property
- The size of the septic tank
- Future maintenance
- And the location of the tank
What other projects should I do at the same time?
Excavation is frequently required when installing a septic tank system (unless you opt for an above-ground tank). Once the excavators have broken ground, you may proceed with further subterranean projects that will save you time and money in the long run, such as:
- Establish underground utilities and construct a retaining wall before beginning work on the sprinkler system.
How Much Does a Septic System Cost?
| Medium: Averages $2,000-$5,000; Runs $4,000-$12,000 in Higher Cost Areas | Enhanced System: $10,000-$20,000+ |
- The cost of installing or rebuilding a traditional septic system (including the tank) is from $2,000 to $5,000 in the Midwest, but can range from $4,000 to $12,000 or more in locations with higher material and labor costs. Septic systems that are designed, engineered-like or alternative septic systems, such as mounds, soil/peat filters, aerobic systems, and/or artificial wetlands, can cost $10,000 to $20,000 or more, according to the Rhode Island Regional Water Quality Program. These alternative septic systems perform better than the conventional technique in areas with high groundwater levels or soil that is slowly or fast percolating, as well as in areas near drinking water supplies, wetlands, coastal ponds, or other water resources. Simply installing a septic tank will cost between $500 and $1,800 based on its size (varying from 300 to 1,000 gallons) and kind. It costs an additional $100-$200 to purchase piping and other necessary supplies
- New Mexico State University gives an overview of the septic tank installation process. Many locations, however, require that a septic system be planned and constructed by experienced and licensed experts
- For more information, contact your local or state sanitation agency.
Related articles:Septic Tank Cleaning,Sewer Line Replacement,Replacing Copper Pipes What should be included:
- It is necessary to employ Septic systems when sewage treatment plants are not accessible, which is typically the case in rural or suburban areas with big lots. Essentially, a septic tank is a huge, underground, waterproof container that can be constructed of concrete, fiberglass, or plastic (polyethylene). An explanation of how septic systems function and where they might be utilized can be found at the North Carolina State University Ag Extension
- Installing or replacing a septic system might take anything from a few days to a week or more. The procedure entails substantial excavating, which is frequently accomplished using powerful earth-moving equipment.
- The majority of counties and states require a construction permit for the installation or replacement of a septic system, which may cost anywhere from $250 to $1,000 or more depending on the location and complexity of the job. For further information, contact your local building and planning department. A septic system installation typically entails substantial digging and damage to the landscaping
- New grass and other plantings can cost anywhere from $100 to $1,000 or more.
- Unlike individual septic tanks, each house has its own underground septic tank, but all of the septic tanks are connected to a single drainfield, leachfield, or soil absorption system. A cluster septic system, which is often implemented by developers, distributes the expense of drainfield installation and maintenance across a large number of dwellings.
- To find out if your local sanitation agency maintains a list of licensed septic installation firms, contact them and ask. Onsite wastewater recycling contractors can be found by contacting the National Onsite Wastewater Recycling Association for recommendations. Inquire about training and previous experience. Check to see if the firm is legally bonded, insured, and licensed in your jurisdiction.
| Posted by:Fredbill in Ashland, VA. | Posted:October 28th, 2020 10:10AM |
| Type:PVC pipe |
When flushing my toilet during wet weather, it was gurggling and not flowing out properly. Septic company wants to replace old black pipe with PVC pipe running 80 feet from septic tank to distribution box. They think the 65 year-old black pipe is collapsing. Is $37.50 per foot a reasonable price?
| Posted by:Fiorella in Miami, FL. | Posted:July 28th, 2020 05:07PM |
| Type:Conventional septic |
Septic tank needed repair. House did not have a drain fill. Had one collapsed leg that was installed years back. Repair was done to the tank and an entire drain fill with 5 legs was installed. My house is located in a high water table. I hired a reputable plumbing company that offers a three years warranty. Is this a reasonable price to pay for repairing a septic tank and installing a complete drain fill with 5 legs?
| Posted by:Dorie Dew in Nederland, CO. | Posted:May 22nd, 2020 02:05PM |
| Type:leach field install |
I am being told that because of county planning dept regs and not enuf “soil” (4 ft) before bedrock here in the Rockies, it will cost $40,000 to install a septic system for a 2 bedroom home (the smallest unit). Please tell me there is an alternative!
| Posted by:in Stone Mountain/atlanta, GA. | Posted:September 9th, 2019 04:09PM |
| Type:New system |
1000 gallon septic tank with 195 feet of quick 4 plus high capacity infiltrator per county code. Inlet line from house to tank plumbing with level 3 soil test and permit. By Easy Clean Septic 678-532-1276 Easycleanseptic.com
| Posted by:in Stone Mountain/atlanta, GA. | Posted:September 9th, 2019 04:09PM |
| Type:New system |
1000 gallon septic tank with 195 feet of quick 4 plus high capacity infiltrator per county code.
Inlet line from house to tank plumbing with level 3 soil test and permit.
| Posted by:Gregory Chappel in Trinidad, CA. | Posted:August 15th, 2019 01:08PM |
| Type:New tank and drain field |
1500 gallon tank, 4″line, 90′ rock trenches took 3 days
| Posted by:Unclebob in McArthur, CA. | Posted:January 26th, 2019 09:01AM |
| Type:Trailer park |
I fought septic tank, leach field problems for years. this is a trailer park, with 35 trailers going into a 7500 gallon tank with 1000 feet in length of leach field. The killer was cooking oil and grease. Plugged up the leach field. Educating the tenants made a huge difference. Then I found the magical cheap combination that worked much better than those expensive enzymes.Equal parts, Yeast, Brown Sugar, and Baking soda. I mix a pound of each and flush it down a toilet every couple of months.
Sams club and Costco sell it in bulk cheap.
| Posted by:a user in moreland, GA. | Posted:July 20th, 2018 12:07AM |
That seems like a lot of money for s single drain line
| Posted by:Sfr Development LLC in Boone, NC. | Posted:August 11th, 2017 12:08PM |
| Type:Conventional 2 Foot Chambers |
1000 gallon tank. In Mountains Boone NC. Have 30 inches to 48 inches of soil. 3 – 60 Feet 2 foot chamber lines
| Posted by:rrrr in berlin, NJ. | Posted:July 12th, 2017 02:07PM |
| Type:septic |
location-south jersey-sandy soil approx cost please? looking for economy and conformity.
| Posted by:Any Help Appreciated in Charleston, SC. | Posted:May 12th, 2017 08:05AM |
Getting ready to purchase a piece of land that requires a septic system in order to build. From soup to nuts, (permits, materials, installation) what should I be looking at for total cost? This house will be built very close to water(Charleston, SC less than.5 miles) How long does the process typically take? Any and all help truly appreciated
| Posted by:Ken Carbaugh in Leesburg, VA. | Posted:June 20th, 2016 06:06PM |
| Type:conventional to alternative systems |
A perc or perk test in Northern Va from a licensed consultant will cost between 1200-2500 dollars depending the district and county fees. Fairfax County costs are 2-4x as much due to local health dept bureaucracy and redtape requiring a surveyor and engineer to be used for any certification or permitting. Real costs of conventional systems (3-4 bedrooms) are from 14-25k depending on the soil percolation results and whether or not a pump is required. If the system is an alternative (BAT in MD) the design costs add 1000-2500 in costs and the installation of the specialized equipment adds costs that can total 20-35,000 easily.
Your property is the most valuable asset you will own so be careful with the land you contract to purchase and beware not all property is equal in value for development.
| Posted by:Bob42 in High rolls, NM. | Posted:March 25th, 2016 12:03PM |
| Type:Concrete tank, leachfield |
$5500 was the total cost for everything including permits and inspection certificate, tank, pipes, new leachfield etc. I live rurally in a mountainous region with sloping land so more work was required to remediate the land for the leach field to be level. Took about a week from contract signing to completion.
| Posted by:Susana in cumming, GA. | Posted:August 24th, 2015 04:08PM |
| Type:treating the leach field |
I had a septic company come to do a septic tank pump for $150 but they said I needed a more expensive leach field treatment at a cost of over $2500 even thought there is no back up or smell anywhere.
They wind up doing an enxyme one leaving me with 6 gallons of liquid enzyme I am suppose to pour down the toiled once a month. My son says I was ripped off. Is he right?
| Posted by:payed too much? in Effort, PA. | Posted:August 2nd, 2015 11:08PM |
| Type:dual tank w mound |
Had Pump replaced as well as wire to house, dug up yard, to replace line, replaced pump, didn’t take garbage, didn’t clean up landscape, pump both tanks included in price, found truck parts in driveway and tanks not pumped, claim truck broke be back to pump.was this a lot, I had to rake out landscape and driveway, clean wires, boxes and garbage left behind,.I hope they pump the tanks soon.
| Posted by:Daytrp in Eldersburg, MD. | Posted:July 17th, 2015 08:07PM |
| Type:Repair – new construction |
Repair permit: $130-450 depending on county.New construction permits: $250-550.New septic $16-22k for advanced treatment, $8-10k conventional Perc test for repair: $850-$1,400 takes 2-6 hours. Done with county sanatarian onsite. A common septic repair: (installation of 2 – 60′ long x 3′ wide x 8′ deep with 4′ of stone below pipe invert) runs about $6,500.Trench dimensions are determined by number of bedrooms (occupancy) and percolation rates from perc test. price varies depending on Trench size.
Septic tank add $2,500-3,500 Pump chamber, pump and controls add $4,000-5,000.
Some states Have programs to help upgrade your septic tank.
Specailty jobs, difficulty of access, heavy rock, all add to the bid price
| Posted by:ABMCCAA in Bakersfield, CA. | Posted:June 26th, 2015 05:06PM |
New 1500 Gallon Tank, Engineering, 60′ of Leach Field with Rock base drainage system. 50 ton of 3/4″ rock, new 4″ main line to house, soils testing and permits. Took 3 days total.
| Posted by:andrewbasil in hemet, CA. | Posted:March 23rd, 2015 06:03AM |
| Type:simple leach line replacement |
75 feet of leach line were dug up and replaced the. attached up to original fifteen hundred gallon 1973 concrete septic tank and re buried. they had to knock down two fruit trees and by accident sheared off a water tap. (Having not repaired the water line it has now become a 5 foot stream shooting straight up in air.) I do feel grandmother was taken advantage and charged double of not more for services that. and this is the worst part. a permit nor independent inspection was never done for this job.
Help me out here what do I do?
| Posted by:ltodd kinsey in cda, ID. | Posted:February 26th, 2015 11:02PM |
| Type:all |
If properly maintained a working system should never need pumped
| Posted by:M. IRIARTE in STROUDSBUR, PA. | Posted:February 4th, 2015 05:02AM |
| Type:SEPTIC |
ANYONE IN THE POCONOS HAS HAD THEIR SEPTIC SYSTEM REPLACE. WHAT WAS THE COST OF REPLACEMENT.WOULD LIKE TO GET FEEDBACK Page 2 of 2-Previous12 External Resources:
- Twri.tamu.edu/reports/1999/l5234.pdf
- sohioline.osu.edu/aex-fact/0744.html
- s
More Articles on the Subject of the Home and Garden
| Check Out All Costs for Home and Garden | How Much Does a Kitchen Remodeling Cost? | How Much Does a Propane Tank Cost? | How Much Does a Plumber Cost? |
| CostHelper is based in Silicon Valley and provides consumers with unbiased price information about thousands of goods and services. Our writers are experienced journalists who adhere to our stricteditorial ethics policy. |
