How Figure Out How To Find Septic Tank? (TOP 5 Tips)

Most septic tanks are around 10-25 feet away from your home, and cannot be closer than five feet. Once you feel the probe striking flat concrete, fiberglass or polyethylene, you will have located your tank. Another way to find the septic tank using the sewer pipe is to go through the pipe itself.

How do I find out where my septic tank is located?

Follow the Main Sewer Line Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside. The sewer pipes will lead to where your septic tank is located.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

How do you find a buried septic tank?

Tips for locating your septic tank

1. If the septic tank lid is underground, you can use a metal detector to locate it.
2. You can use a flushable transmitter that is flushed in the toilet and then the transmitter is tracked with a receiver.

Can a metal detector find a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

What are the signs that your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

• Your Drains Are Taking Forever.
• Standing Water Over Your Septic Tank.
• Bad Smells Coming From Your Yard.
• You Hear Gurgling Water.
• You Have A Sewage Backup.
• How often should you empty your septic tank?

How do I know if my house has a septic tank?

One way to determine whether or not your home has a septic system or is served by the public sewer system is to look at your water bill. If you are using a septic system for wastewater management, then you’re likely to see a charge of $0 for wastewater or sewer services from the utility company.

How do you find a septic tank in an old house?

Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.

Do I have to change my septic tank?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

What happens if septic tank not pumped?

What Are the Consequences of Not Pumping Your Tank? If the tank is not pumped, the solids will build up in the tank and the holding capacity of the tank will be diminished. Eventually, the solids will reach the pipe that feeds into the drain field, causing a clog. Waste water backing up into the house.

How far down is a leach field?

A typical drainfield trench is 18 to 30 inches in depth, with a maximum soil cover over the disposal field of 36 inches.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. The best and easiest way to find below-ground objects such as these is with a metal detector.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.

Inspect Your Property

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.

• Paved surfaces
• Unique landscaping
• Your water well, if you have one
• And other features.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.

Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.

Don’t Try to Fix Septic Tank Issues Yourself

Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.

Schedule Septic Tank Maintenance

Professionals should handle septic tank difficulties. The Original Plumber can do routine maintenance on your septic tank or examine any problems you may have once you’ve located the tank. Opening the septic tank lid might result in major health consequences due to the noxious vapors that are expelled. It is possible to sustain serious harm or even death if one falls into an open septic tank. Knowing where your septic tank is and how to locate it is beneficial, but it is also important to be aware of the potential health dangers associated with opening the tank.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.

If you’re also using well water, it’s possible that you won’t receive one at all.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis. Preventing worse problems and the need for costly repairs down the line may be accomplished via proper septic system maintenance. All of the heavy lifting has been delegated to our team of professionals.

Looking for Your Septic Tank? Here’s How to Find It

“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.

Why you need to know where your septic tank is located

If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.

In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.

How to find your septic tank

1. Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
2. Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.

After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.

• The post was published on July 16, 2019 under the category Septic Tank System.

How to Locate Your Septic Tank

It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.

This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.

How To Find A Septic Tank: Step By Step

It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.

The Plumbing Experts have put out all you need to know about locating the septic tank on your property in this blog post for your convenience.

1. Gather Some Helpful Tools

It is critical to maintain the health of your septic tank system since it is responsible for securely storing and controlling the wastewater that exits your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with its location. Unfortunately, finding your tank is not always simple, and many plumbers charge extra to discover them, which is especially true if your septic tank lid is hidden beneath the earth.

1. A soil probe is one of the most useful instruments for locating a septic tank.
2. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.
3. Using this method, you may also locate the cover for your septic tank.
4. While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.

2. Use a Septic Tank Map

If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.

3. Start Ruling Areas Out

The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:

• Immediately adjacent to your well
• Beneath your home
• Directly against your home
• For example, underneath your driveway
• Under trees
• And other locations. Structures like a patio or deck are good examples of this.

4. Inspect Your Property

Directly across the street from your well; beneath your house; up against your house; For example, underneath your driveway; among trees; and so on and so forth. Under constructions such as a patio or a deck, for example

• Your water well, if you have one (for a variety of reasons that are rather clear)
• Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
• Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
• Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping

5. Inspect Your Yard

A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:

• If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
• Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.

The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.

6. Follow Your Sewer Main/Sewer Pipes

Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.

The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.

If the line is labeled, it is usually made of plastic or rubber. It is important to determine where this line exits your property and in which direction it is moving, as it often travels straight out to the septic tank itself.

7. Check Your Property Records

Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.

If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.

What to Do Once You Find Your Septic Tank

Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities. You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!

How to locate your septic tank and your drainfield

Septic systems on-site are used for accepting and treating wastewater in homes that are not linked to the municipal wastewater management system. A septic system is comprised of three components: a septic tank, a drain field, and piping. As a homeowner, it is your responsibility to properly operate and maintain your septic system in order to avoid system failure. For example, depending on the legislation in your area, you may be compelled to pump it on a regular basis. It is impossible to perform maintenance operations, however, if you do not know where the tank is located.

Steps to follow to locate your septic tank and drain field

The contractor that designed and constructed the septic tank on your property should have submitted an as-built diagram with the local health authority before starting work on the project. In the event that you have the contractor’s contact information, you can ask them for a schematic, which you can then use to pinpoint the location of your septic tank. If you do not have a copy of the schematic, you can request one from the local authorities. Depending on whether the installed system included electrical components, the schematic may be available at the regional building department offices.

When it comes to pinpointing the exact placement of your septic tank and drain field, this graphic may be quite helpful. If you are unable to locate the tank using this diagram, you will need to do more research on the land in order to determine its position.

The sewage outlet pipe is an excellent spot to start your physical evaluation of the property because it is accessible from the outside. This pipe is commonly found in the basement of a home, and it is a 4″ black pipe with a cleanout at the bottom. If the cleanout is behind a wall or in a closet, it is considered a hidden location. Simply look for possible access coverings or a structure that might be concealing it. Lift pumps are sometimes installed in basements to assist in pumping sewage from the building.

• Having discovered it, flush a toilet and listen to the pump to determine where the sewage is being discharged.
• You should now be able to see the general orientation of the septic tank and drain field from this point.
• The septic tank will be located a few meters away from the home, and the outflow pipe may be at an angle of 30 or 45 degrees from the house.
• Work your way around the home in a circle, starting at an electrical outlet and continuing until you find the septic tank.

Tips for locating your septic tank

Septic tank lids should be visible from the outside. An underground riser may have been added, which will make it simple to find your septic tank in some instances. However, it is conceivable that the septic tank cover is buried underground, which is especially true for older homes. Following are some pointers to assist you in locating the septic tank in this and other similar situations.

• It may be possible to discover the septic tank lid underneath using a metal detector if it is buried. Prevent wearing footwear that contains steel or any other metal in order to avoid interfering with the readings of the detector
• Instead, you can use a flushable transmitter that is flushed down the toilet and then tracked with a receiver. When it comes to septic tanks, the strongest signal will be seen close to the intake region of the tank.

Depending on whether the septic tank is above or below ground, you may have to dig to get to it. Construction materials for septic tanks include concrete, fiberglass, or plastic, and their shapes can range from oblong to cylindrical to rectangular. The majority of modern septic tanks will have their lids positioned in the center of the tank, and the lid should be within three feet of the ground surface in most cases. However, depending on a variety of conditions, such as farming and other human activities on the property, it is conceivable that it will be significantly deeper.

Additionally, you may use a small steel rod to probe the earth in order to pinpoint exactly where the tank is located as you continue digging.

Inspecting the tank

It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been identified. First and foremost, you may unscrew the lid to inspect the scum and sludge layer beneath it. In addition, the use of tracer dye tablets allows you to check the septic tank without having to dig it up. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of two days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field has a glowing green hue surrounding it.

It is possible that someone will fall into the tank, causing significant damage or possibly death. Additionally, all septic tank maintenance techniques should be carried out in accordance with the legislation governing the sewage system.

Conclusion

It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been found. You may first unscrew the cover to inspect the scum and sludge deposit on the inside of the drain pipe. With the use of tracer dye tablets, you may also do a non-invasive inspection of your septic tank. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of 2 days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field is a vivid green hue in the surrounding area.

It is possible that someone will fall into the tank, causing major harm or perhaps death to themselves.

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

• 3.
• Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
• Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
• When you do, that’s when your septic tank comes into play!
• Look for the Lid.
• You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
• Those areas should be excavated in order to disclose the lids.
• Get in touch with the pros.
• Lifting concrete lids will necessitate the use of specialized equipment.
• A fall into an unprotected septic tank has the potential to be lethal.
• Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

How to Locate a Septic Tank

A surprising number of homeowners have had to figure out how to find the location of a septic tank on their premises. If you’re purchasing a home with a septic system or discover that your property’s tank hasn’t been maintained in years, you’ll want to know where the tank is located because all septic tanks must be pumped at some point in time. In the course of a real estate transaction, the property owners or real estate agent may be aware of the location of the tank. Inquire about the “as-built,” which is a schematic of the septic system and the specifics of its installation.

Unfortunately, locating the septic tank may not be as simple as it appears.

Because septic system permits have only been needed in Oregon since 1972, you may have to depend on visual indicators to determine whether your system is working properly.

1.Follow the Outgoing Sewer Pipe

Look for the four-inch sewage pipe that runs through the structure and the location where it exits the building in the basement or crawl space. Locate the location outside the building where the pipe exits the building or the location of an access cover over the pipe. It is required that septic tanks be at least five feet away from the structure, although they are usually between 10 and 25 feet away. You may follow the pipe all the way to the tank using a metal probe. It is important to note that sewage lines may curve and run around the corner of a building rather than following a straight path to the holding tank.

2.Search for Septic Tank Risers and Lids

Depending on their age, septic tanks are either one- or two-compartment structures. Each compartment has a cover, with two additional lids for dual-compartment tanks that were added later. If the tank includes an access point known as a riser, the lid may be readily visible from outside. Look for round, plastic discs that are about a foot or two in diameter. Due to the fact that the lids might be flush with the ground or just a few inches above it, they can get overrun with grass and other plants over time.

Tanks without risers are likewise equipped with lids, however they are located underground.

3.Find the Drain Field First

In the absence of a riser and lid, search for indicators of a drain field, such as an area of grass that grows more quickly or more slowly than the rest of the yard, grass that is a different color from the rest of the yard, or areas where snow melts more quickly than in other parts of the yard. Spots of high or low ground in the yard might possibly indicate the presence of a subterranean tank or drain field. You will be able to discover the tank if you probe these regions.

Reasons to Hire a Contractor for Help

Attempting to locate a septic tank on your own can be risky, and in some cases, lethal, if the septic system is old and in danger of collapse. In the event that you fall into a cesspool, dry well, or septic tank, you will die.

Removing septic tank lids on your own might potentially put you at risk of contracting bacterial or virus diseases. If you detect any of the following issues, please contact a contractor to assist you in locating or inspecting your septic tank:

• Soil that is sinking around the tank or drain field. Drainage backup into the home’s sewer system, or toilet backup
• A foul odor in the area where you assume the tank and drain field are located
• When there is no rain, pooling water, muddy soil, or spongy grass might occur. Septic tank covers that are rusted, cracked, or have been replaced with improvised lids are prohibited.

Even though you may be ashamed about forgetting where your septic tank is, it is a very frequent problem among homeowners. A contractor may assist you in locating it, and he or she may do it as part of the pumping service. If you need assistance locating your tank or if you have any other questions, please contact us at 503-630-7802. We are available to assist you!

How to find your Septic Tank at Home

When was the last time you paused to think about what happens to the things you flush down the toilet? It’s a little disgusting to think about, isn’t it? It’s possible that you’re conjuring up images of cobwebby crawlspaces with a swarm of creepy-crawly unmentionable creatures sliding, slithering, creeping, or crawling over crusty, rusted, ooey-gooey piping that’s oozing slimy goo from every joint. If this sounds like something you’re picturing then you’re not too far off the mark. I sincerely hope you are.

• That’s why I’d want to assist you in learning how to locate your septic tank.
• Simply dial 911 and ask for assistance in a calm manner.
• Most hide-and-seek games are won by septic tanks, which are well-known for their amazing ability to outperform the typical human rival.
• The good news is that.
• Contrary to common misconception, septic tanks are not often found in attics, basements, or any of the numerous closets that may exist in a house or apartment.
• Relax in your favorite place for a few minutes with your favorite beverage in hand.
• Yes, you read that correctly: your yard.

Alternatively, you can sink.

Or whatever it is that’s causing the terror to rise in your chest to rise in your chest.

Septic tanks are normally installed in one of your backyards or on your property.

How are you doing?

If your septic tank is in close proximity to your well, this should be avoided.

Septic tanks are often located on the other side of a house from where your home is located.

Tanks are often placed with their tops buried beneath the surface of the ground, usually at least 12 inches below the level of the ground’s surface.

A plastic access tube or a concrete riser structure that runs from the top of the tank to the ground level will often be included to give access for a Septic Pumping firm to empty the tank. Shankster Brothers (also known as Shanksters)

Many septic tank installers will attempt to blend these access risers into the surrounding landscaping so they don’t create an ugly eyesore.

So the next step is to mentally go about your yard, looking for any circular, plastic lids that could be lying around. These can range in size from 10 inches to 24 inches in diameter and can be either black or green. Second, if the answer is no, consider any round, square, or rectangular concrete lids that may be present in your yard or landscaping as a possible source of contamination. Often, they will be practically flat with the surface of the ground, allowing a lawnmower or rake to pass directly over the top of them without causing damage.

1. Typically, the septic tank access will be no more than 10 feet away from your home, but in the event of an older home or a subsequent addition to the property, they may be closer than that.
2. Hopefully, you have a basement to store your belongings.
3. If your home does not have a basement or crawlspace, we will rely on other indications to locate your home.
4. All of these pipes should converge into a single bigger pipe (usually 4 inches in diameter) that exits the house via one of the home’s walls.
5. Now it’s time to go outdoors.

Check the area where the pipe comes out of the house. There may be a PVC pipe extending to the surface, with a threaded cleanout cap on it. If you find this, you’re well on the way to victory.

Take a check at the roof if your property is constructed on a slab with no basement or crawlspace beneath it. Check the roof for a vent pipe that is coming out of it. An internal vent that travels straight up, through the roof, and out the top of your home is common. If you can identify that vent, it might be possible to figure out where the pipe is departing the house. Continue walking outside from the house for a few steps, keeping an eye out for that round, square, or rectangular cover. If you can’t discover it, check for a little sunken place in the yard that could be hiding anything.

If you notice one of those, you might want to look underneath it to see if there is an entry point hidden there.

It’s possible that here is where your tank is lurking. If none of these suggestions have resulted in victory, and you begin to observe your neighbors peering through their blinds with those anxious glances that neighbors are so prone to giving.give us a call!

We have foundseptic tanksin many strange and unpredictable places. Here’s hoping you win the game on how to find your septic tank. Here tanky, tanky, tanky! If you need to schedule aseptic tank cleaning, pumping, or inspection, don’t hesitate to call Shankster Bros at(260)-982-7111. any time.

Take a check at your roof if your house is constructed on a slab with no basement or crawlspace underneath it. Check the roof for a vent pipe that comes out of the top. Often, the piping within your home will have a vent that runs straight up, all the way through the roof, and then comes out the top. Locating that vent may provide you with some insight into where the pipe is departing the house. Move outward from the home a few feet and look for the round, square, or rectangular lid that you were looking for previously.

Skilled installers may choose to disguise the entry point by using round or square patio stones.

The toilet or other fixtures drainage difficulties may be caused by a damp or wet location in the yard, which you may want to investigate if you have been experiencing such problems.

If none of these suggestions have resulted in victory, and you begin to observe your neighbors peering through their blinds with those anxious looks that neighbors are so prone to giving you, give us a call right away.

How Do I Find My Septic Tank

Take a look at your roof if your property is constructed on a slab with no foundation or crawlspace beneath it. Look for a vent pipe that emerges from the roof. An internal vent that runs straight up, all the way through the roof, and sticks out the top of your home is common. Locating that vent may provide you with an indication of where the pipe is departing the home. Follow the path of least resistance outside the home, seeking for the round, square, or rectangular lid. If you can’t discover it, try for a little sunken location in the yard.

Whether you notice one of those, you might want to check below it to see if it is blocking the entrance.

This might be the location where your tank is hidden.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

1. They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
2. Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
3. A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
4. Using an electronic service locator, you may locate a septic tank.
5. In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
6. Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
7. Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

• There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.

Check the rest of the toilets in the home by repeating the procedure.

Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.

a link to the page’s load

How to Find a Septic Tank With a Metal Detector

For sewage treatment in the United States, around 48% of households in rural and outlying regions depend on septic tanks or septic systems. Many of these systems have been operating without regular maintenance for many years. It is necessary to locate your septic tank in the event that sewage is backing up into your home or if your main drain line has become obstructed. Throughout this post, we’ll go over the basics of how septic systems function before showing you how to identify your septic tank in six simple stages.

How do septic systems work?

A septic system is made up of two parts: the septic tank and the drain field (or leach field).

Septic Tank

Waste from toilets, sinks, and showers is sent down a main sewage line and into a holding tank known as the septic tank. A septic tank is a large, subterranean container that acts as the initial stage of a home’s sewage treatment system by collecting and treating sewage. Watertight containers such as concrete, steel, plastic, and fiberglass are used to construct the tank. Until the particles and liquids separate into three different layers, sewage is allowed to remain in the septic tank. This picture shows how sewage from the home drains into a two-compartment underground septic tank.

The liquid wastes are subsequently discharged into the drain field.

The bacteria produce a sludge that is “digested” and stays in the tank until it is drained.

This stratum is referred to as effluent in most circles. The effluent drains out of the septic tank and into the drain field, where it is filtered by gravel and dirt before being discharged.

Drain Field

Drain fields are composed of layers of gravel and dirt that allow liquid sewage to flow down. It eventually becomes part of the groundwater supply. Aerobic bacteria (bacteria that require oxygen to survive) and other microbes decompose the organic debris that remains.

What happens if a septic tank gets too full?

In the event that your septic tank becomes overflowing, sewage may back up into your home. It is more difficult to breakdown sludge than it is to collect it. If the sludge isn’t cleaned, the solids will build up until they overflow into the drain field, causing the drain to back up. This has the potential to clog pipes and produce a backup. The sludge must be cleared on a regular basis in order to avoid this. Many households only get their tanks emptied after the system malfunctions. Waiting until that stage can result in repair expenses in the tens of thousands of dollars.

6 Steps to Locate a Septic Tank

Water from your toilets, sinks, and showers is collected in a main drain pipe and disposed of properly. This line departs your home and enters your septic tank through the basement or crawl area where it was installed. Find the line in question. Afterwards, walk outside and look for the identical location on the opposite side of the wall. Make a note of this spot since you’ll need it in a moment.

2. Check Permits and Public Records

The majority of county health agencies keep public records of septic system installation permits on their websites. These permits must be accompanied by a schematic or design depicting the proposed location of the septic tank and drainage field systems. They also give a description of the tank’s dimensions and construction material. Having this information can be quite beneficial when trying to locate a submerged tank lid. In some cases, depending on the age of your septic system and the digitization efforts of your county’s health department, you may be able to do a public records search online.

If you live in Colorado, we’ve provided links below that will allow you to check septic records in a few different areas.

• Colorado’s counties of Adams, Arapahoe, and Douglas Colorado Septic Records Search
• Colorado Permits Search
• El Paso County Records Search
• Jefferson County Septic Records Search
• Jefferson County Records Search
• Mesa County Septic Systems Search
• Pueblo County Records Search. Colorado Septic Records Search
• Pueblo County Records Search

3. Determine Septic Tank Material

If you’ve located your septic permit, you’ll find information about the size, shape, and material of your septic tank there as well. But don’t be concerned if your septic data aren’t readily available. We can perform some basic detective work to determine what material your septic system is built of. Let’s start with a look at the materials.

Types of Septic Tank Materials

Construction of septic tanks is mostly done using four types of materials: concrete, steel, fiberglass, and polyethylene plastic. Until the 1880s, the most extensively used septic tank material was concrete, which was then replaced by steel. These tanks have a lifespan of around 40 years and are built to last. They are susceptible to cracking, however, in locations where temperature variations are strong and frequent. Concrete tanks are frequently required by municipalities that have strict requirements on septic system construction.

• Steel septic tanks begin to corrode within 20 to 25 years of installation in most regions.
• If a human or animal walks across the weakened tank, it may collapse under the weight of the person or animal.
• They will not break or corrode, however, in contrast to concrete or steel tanks.
• PlasticSeptic tanks made of polyethylene have been in use since the 1980s.

They are not susceptible to rusting and are less prone to break when compared to concrete. They are, however, not quite as long-lasting. Because of the weight of the earth above them, or because a vehicle passes over the area where they are buried, plastic tanks are susceptible to collapse.

How Old is Your House?

Next, let’s determine the approximate age of your home. In some cases, all you need to do is take a glance at the house’s façade to get an idea of how old it really is. However, you may examine the tax assessor’s records in your county to get a more precise assessment. Similarly to searching for septic records, your mileage may vary depending on which county’s digitized documents you are searching for. Let’s go over an example search utilizing Boulder County’s Property Search tool so that you can have a better sense of what you should be looking for.

1. Look up your home address on the internet. When searching for a home, some programs provide separate areas for your address and street name, while others (such as Boulder County) merge the two into a single search box. Look for information on Deeds and/or Sales Records in the public domain. You’ll find a list of transactions here, with dates showing when the property was purchased and sold. Find the transaction that occurred on the earliest possible date. This is most likely the year in which your home was constructed.

Attempt to locate your location. When searching for a home, some programs offer separate areas for your address and street name, while others (such as Boulder County) merge the two into a single search box. Keep an eye out for information about Deeds and/or Sales Records. You may go through this section to see a list of transactions that shows you when the property was purchased and sold. Find the transaction that took place on the earliest date possible. Most likely, this corresponds to the year in which your home was constructed.

4A. If it’s Concrete or Steel, Use a Metal Detector

After coming to the conclusion that the tank is most likely built of concrete or steel in Step 3, a metal detector may be used to make the work of locating it much simpler. But not just any metal detector will do. It must be the right one. Standard metal detectors have a depth range of 6 – 8″ (15 – 20 cm) below the surface of the ground. As previously stated, the majority of septic tanks are placed 1′ to 3′ (0.3 m to 1 m) underground, putting them outside of the acceptable range. An advanced sort of metal detector known as a Magnetic Locator, which can detect objects as deep as 16′ (4.8 m), is available for purchase.

How to Use a Metal Detector to Search for a Septic Tank

If you have a septic permit record, you may refer to it to figure out how far you need to go to install a septic tank. Start at the point where the drain line meets the home and work your way out to where the septic tank is shown on the diagram. Keep in mind that this graphic depicts the proposed installation area and may not accurately depict the actual ground conditions on the site. We’ll have a look at the illustration below. One inch (2.5 centimeters) is equivalent to fifty feet (50 meters).

By using a ruler to measure the design, we’ve determined that the septic tank should be roughly 13′ (3.96 m) away from the home.

1. If you have a septic permit record, you may refer to it to figure out how far you need to go to construct a septic tank. Start at the point where the drain line meets the home and work your way out to where the septic tank should be. Keep in mind that this graphic represents the proposed installation area and may not accurately depict the actual ground conditions. Examine the figure below to see what I mean. One inch (2.5 centimeters) is equivalent to fifty feet (50 meters), as seen in the lower left corner (15 m). We’ve determined that the septic tank should be roughly 13′ (3.96 m) away from the home by using a ruler to measure the diagram. We should broaden our search area to include anything from 10′ (3.05 m) to 20′ (3.05 m) because the sewage drain pipe was going to be put at an angle (6.1 m).

4B. If it’s Plastic or Fiberglass, Probe Gently

Septic tanks made of plastic or fiberglass are typically buried one to two feet (0.3 to 0.91 m) below ground level. They feature circular covers made of green or black plastic that are roughly two feet (0.91 m) wide and have a diameter of around two feet (0.91 m). Due to the fact that these tanks are totally made of plastic, a metal detector will not be of use in locating them. In this situation, a soil probe is really useful. An inexpensive soil sampling instrument, soil probes are comprised of a 4′ (1.2 m) metal rod with a pointed tip on one end and are used for soil sample.

Gently poke the earth with a soil probe every 2 to 3 feet, using a light touch (0.61 to 0.91 m).

Make a note of any areas where you encounter resistance and continue exploring around in your search area. The use of a soft touch is essential here, since the metal tip of the probe can cause damage to plastic septic tanks (and sewage lines) if too much force is used.

5. Time to Dig

Following the placement of an amagnetic locator (or the probing of the ground) to record the places with the highest signal strength, you are ready to begin digging. Septic tank lids can be located anywhere from 4″ (10 cm) to 4′ (1.2 m) below the surface of the ground.

6. Mark the Location for Future Maintenance

Having discovered your septic tank, you’ll want to ensure that it can be readily detected and accessed in the event that it has to be repaired or replaced. You may accomplish this by installing a septic tank riser. Sewage Tank Risers are devices that provide for easy access to the septic tank from the ground. They are shafts made of plastic or concrete that link the top of the tank to the surface of the ground below the tank. The tank lid will no longer require you to dig to access it whenever maintenance is required.