The control floats are set so that a specific volume of sewage is sent to the drainfield. This specific amount is referred to as a “dose.” When sewage in the pump tank reaches the “on” float, the pump is activated and pumps sewage out until it reaches the “off” float (See diagram below.)
How does a septic tank work?
- The septic tank digests organic matter and separates floatable matter (e.g., oils and grease) and solids from the wastewater.
How do lift station floats work?
A transducer works by varying the amount of DC voltage it sends back to the control panel in relation to the water level in the wet-well. The floats run off a low voltage system and use either the pump controller or a printed circuit that activates the pumps. Each pump also has a hand-off-automatic (HOA) switch.
How do I know if my float switch is bad?
If it is, try this easy fix: check whether an object is preventing the overfill float from moving up and down freely. If the float is stuck in its highest position, the fill valve won’t let water into the tub. If that doesn’t take care of it, the overfill float switch or water inlet valve may be broken.
How do you adjust a float switch?
Adjusting a manual float switch is easy. Start by moving the rod or tether up or down based on the water level in the pit. Most systems can be adjusted by hand or with a normal sized screw driver. Shorter tethers and rods work best for lower water levels while higher tethers and rods are better for higher water levels.
Do float switches fail?
While these switches are very reliable for industrial applications, they can fail. As with any piece of equipment, a float switch will have a limited operating life. However, if the switch is used properly and maintained, there is no reason that it should not last for many years.
How does a tether switch work?
A tether float switch features a float tethered to the pump and is more common with sewage pumps or larger basins. As the water rises, the float rises, causing the tether to flip the switch and turn on the pump.
What happens when a lift station fails?
In the event of a lift station failure, by either a forcemain break, power outage, or pump failure, wastewater will collect in the lift station wet well and backup into the collection system. Wastewater lift stations can be a source of bad odors that become a nuisance to neighboring properties.
Is it noisy living next to a pumping station?
Pumping stations can be noisy, however, while they are being built, there are regulations that are put into place to minimise this. There are rules around how close you can build a pumping station to any habitable buildings so that noise and nuisance are kept to a minimum for people who live close by.
How many floats are in a lift station?
Typically four float switches are used: off float, lead float, lag float, and the high water/alarm float.
How do you test a water tank float switch?
Attach the MultiMeter leads to the float switch wires. The Multimeter should be set to the Ohms. The MultiMeter should read zero when the float hangs in the down position. Lifting the float will change the zero to one.
How long do float switches last?
These old float switches didn’t have many operations and needed to be replaced about every 3 years or so, making them expensive to keep up with. However, new float switch manufacturers are producing water level control technology that is getting rid of old float switches for good.
Where is the float switch?
Your float assembly is found inside the dishwasher’s tub, on the bottom. The water that fills your dishwasher lifts the float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher.
Troubleshooting a Sticking Float in a Septic Tank
Pump chambers in septic tanks feature effluent pumps that are actuated by float switches. Float switches are used in septic systems to activate alarms and to shut down and restart effluent pumps. It is possible for float switches that have been put incorrectly or carelessly to become stuck on other wires in the tank or become useless owing to debris in the tank. Sticking float switches fail to warn a homeowner that sewage is backing up into the house. 3ups or failing to switch off an effluent pump are unacceptable.
Septic tank floats should be examined for good operation on a regular basis, and this should be done every time septic tank maintenance is conducted.
Step 1
Remove the lid for the maintenance access hole from the tank and place it to one side.
Step 2
Look for electrical cables and other trash in the tank and note where they are. The wires connecting from the float switches to the pump’s standpipe should be firmly secured and should not obstruct the free movement of the floats in any manner.
Step 3
Reduce the height of the pump hook until it is below the float switch’s position. Raising and lowering the float switch will allow you to determine whether an electrical wire or other debris is preventing it from moving.
Step 4
Ensure that the float is in its completely open position before bumping it. If the pump does not pump or the alarm does not sound, the float has to be bumped again. If the alarm is triggered or the pump is activated, the float should be replaced.
Step 5
Replace the access cover for the septic tank’s upkeep.
Warning
When working around sewage tanks, you should use caution. Don’t forget to put on your safety gear.
How Sewage Pumps Work with Float Switches
There are risks involved in working near sewage tanks. Do not forget to put on your safety gear!
What is a Sewage Pump?
Sewage pumps are pumps that are used to transport sewage liquids and particles from one area to another. They are also known as sewage disposal pumps. Sewage is normally pumped from the basement of the home into the main sewer line in the event of a residence. Sewage pumps are available in two configurations: manual and automated. Manual sewage pumps must be switched on and off on a regular basis, albeit they are generally not advised due to the danger of sewage overflowing. Automatic sewage pumps, on the other hand, work with the assistance of a float switch to operate.
How Sewage Pumps Work?
Sewage pumps are pumps that are used to transport sewage liquids and solids from one area to another. They are also known as sewage treatment plants. For example, in the case of a house, wastewater is often pumped from the basement into an underground sewer system. Sewage pumps are available in two configurations: manually operated and automatically controlled.
Septic tanks with manual sewage pumps must be emptied on a regular basis, albeit this is not advised owing to the risk of sewage overflow. Pumps that operate automatically, on the other hand, are controlled by a float switch.
Float Switches for Sewage Pumps
The float switch is one of the most critical components of a sewage pump since it is responsible for allowing the pump to actually begin pumping. It is typical to see the FN20 Mechanical Sump Switch in residential applications such as sump pumps and basement pumps. It is also possible to utilize this sump float switch for septic tanks and ejector pumps in addition to sump tanks.
Get in touch today!
The float switch is one of the most crucial components of a sewage pump since it is responsible for allowing the pump to begin pumping. Sump pumps and basement pumps are two examples of situations where the FN20 Mechanical Sump Switch is typically found. It is also possible to utilize this sump float switch for septic tanks and ejector pumps in addition to sump systems.
PUMP DUTY SWITCHES
Pump switches are devices that are used to regulate the functioning of a submersible water pump. They have a larger current carrying capacity than control switches. These are often wide angle switches, which means that they must be rotated 90 degrees in order to be switched to the “ON” or “OFF” position. When managing a pump, this is necessary since you must be able to pump out a wide range of water, and it also prevents the float from being stopped by turbulence in the water, which is undesirable.
- Because the float switch will be the conduit via which the power for the submersible pump will be sent, it must be capable of handling at least that amount of current.
- It will be necessary to make a choice on how the amperage float will be mounted once you have determined which amperage float will be required for your application.
- If you get a float switch that comes with a piggy-back connector, the installation is quite straightforward and straightforward.
- a) Float Switch Installation That is all there is to it; your pump will only activate when the float is in the proper position to permit it.
- Because floats are always two-wire devices, in order to install one on a pump, the float switch must be spliced into the “HOT” line coming from the power supply.
- The final choice you have is to choose between mercury and mechanical filtration.
- Mechanical switches are comprised of a ball bearing mounted on a track that rotates back and forth in both directions.
Even though mercury switches are supposed to be more dependable, they are not permitted to be used in some places (see our website for more information) and are only available in 13-amp configurations. Pump Float Switches may be purchased by clicking here.
CONTROL DUTY SWITCHES
Control switches are intended to be used in conjunction with a control panel, and are mostly used for high and low level alerts. Low amperage and small angle are two characteristics that characterize these switches. When using narrow angle float switches, you must change the switch position by 10 degrees. As a result, they are extremely sensitive to changes in water level, making them ideal for use as high or low level alarms, respectively. Making a decision on which control switch to purchase is significantly less difficult.
- Because it will be attached directly to a control panel or alarm box, no control switch will ever be supplied with a plug.
- The “PUMP DOWN” variant will be utilized for notifications at the highest level.
- To purchase a control float switch, please visit this page.
- In the event that one of our floats is not suitable for your use, we have the capability of obtaining many more types and should be able to locate something suitable for your needs.
- If you have any concerns or would like to place a custom order for a float switch, please contact us toll free at 1-877-925-5132.
How to Troubleshoot Septic Float Switches
They are intended to be used in conjunction with a control panel, and are often used to detect high or low levels of activity. Low amperage and small angle are typical characteristics of these switches. Moving 10 degrees is required to activate narrow angle float switches on the water. As a result, they are extremely sensitive to changes in water level, making them ideal for use as high or low level alarms in swimming pools. Making a decision on which control switch to purchase is lot less complicated now.
- Because it will be attached directly to a control panel or alarm box, no control switch will ever come with a plug in it again.
- It will be necessary to utilize the “PUMP DOWN” variant for HIGH level warnings.
- Control Float Switches may be purchased by clicking here.
- In the event that one of our floats is not suitable for your application, we have the capability of obtaining many more types and should be able to locate something suitable for your needs.
Furthermore, we can supply most of our floats with cords in a variety of lengths, including 10ft, 15ft, 20ft, 30ft, and 50ft in length. Please contact us toll free at 1-877-925-5132 with any inquiries or to place an order for a float switch that is not in stock.
Step 1
If the float’s alarm is sounding, turn off the alarm switch on the float. An overflow in the system or a defective float are both indicated by this condition.
Step 2
Anything plumbing-related in your home that discharges water into the septic system, such as the washing machine and dishwasher, must be turned off immediately.
Step 3
Reset the alarm by pressing the button on the wall. Wait between six and eight hours before turning on your water supply. If the alarm does not ring again after this length of time, it is likely that the problem is anything other than a sewage overflow.
Step 4
The float switch should not be turned off by checking the circuit breaker or the GFCI plug (Ground Fault Circuit Interrupter) for a trip. If moisture is allowed to enter the outlet, the GFCI plug will trip. When the circuit is tripped, a light will illuminate to show that it has happened. Attempt to reset the GFCI plug by pressing the button on the plug, or turn off and on the circuit breaker to reset the circuit breaker. If the circuit breaker or GFCI outlet trips again, this indicates that there is a problem with the wiring or that there is moisture in the circuit.
Step 5
Check to see if the pump is activated by pressing the on/off switch on the float switch. A dead switch or a defective pump might be to blame if this doesn’t work for you.
Step 6
Examine any exposed cables and wires to determine whether they have been damaged.
Septic 3 Float System – Is this how it’s supposed to work?
Greetings, fellas. I live in Pennsylvania and have a raised mound septic system. A pump pushes the effluent upward into a 500-gallon dosing tank in my septic tank, which is located at the top of the sand mound. The system is comprised of three floats. The top float activates the alarm, and the center float activates the pump to start it. The bottom float is visible in the tank water, and I can see it floating. I was under the assumption that when the middle float floated upward and turned on, it would activate the pump, which would then remain operational until the bottom float was turned off (stopped floating).
Use a stick to raise the center pump, which then turns on, and even if you drop the middle pump, it will keep pumping until it gets to the level of the lowest bottom float.) However, I went in there only for the sake of checking the system, like I do every year, and discovered that it does not operate in this manner.
The pump kicked into action.
I believe that the bottom float is floating upward, as it should be.
Is my system up and running correctly? What is the normal operation of a three-float system? Wanting to obtain some peace of mind, or calling someone out and having them check it out if this is genuinely not a healthy situation Thank you to everyone.
Septic Tank Float Switch: Functions, Types & Problems
Salutation to all of you! A raised mound septic system is what I have in Pennsylvania. A pump pushes the effluent upward into a 500-gallon dosing tank in my septic tank, which is located towards the top of the slope. Specifically, it is a three-float configuration. As soon as the top float sounds the alarm, the pump begins to operate. The bottom float is visible in the tank water, and I can see it float up to the surface. I was under the assumption that when the middle float floated upward and switched on, it would activate the pump, which would then remain operational until the bottom float was deactivated (stopped floating).
- Use a stick to raise the center pump, which then turns on, and even if you drop the middle pump, it will keep pumping until it gets to the level of the lowest bottom float.
- To raise the center float, I used a stick to help me.
- The pump, on the other hand, ceased working as soon as I let off of the lever.
- The center float, which is responsible for turning on the pump, appears to only be pumping for about 30 seconds when the tank is full, after which it appears to be pleased and shut down.
- What is the normal operation of a three-floating-stage system?
- Everybody, please accept my gratitude.
Functions of A Septic Tank Float Switch
Some readers may be able to figure out what this item is all about just by looking at its name alone. No need to be concerned or embarrassed if you have no understanding what this is about. There is nothing to be embarrassed about. Isn’t it true that we’re all here to learn? Let’s get into the specifics without further ado. Float switches, in their most basic form, are sensors that signal to your pump when it is essential to turn on or off. It is necessary for the water level to have reached a certain level in order for the pump to be activated.
Take the weight of the world off your shoulders with this critical function.
All of this is carried out on an automated basis while you go about your everyday tasks.
Types Of Septic Tank Float Switches
In terms of selecting the most ideal float switch for your needs, there are several alternatives available to consider. Submersible sensors, pump duty floats, mechanical sump switches, control duty floats, and horizontal float switches are some of the most common types of float switches available.
It is required to provide a more detailed explanation of how each of them functions, however brief, in order to better grasp them.
Submersible Sensors
Submersible sensors are a sort of septic tank float switch that is most commonly used in deep sewage tanks. One of the most advantageous characteristics of submersible sensors is their ability to fit into virtually any place. To put it another way, this float switch variant is suitable for tight spaces. It is also advantageous to use a submersible sensor since it allows you to obtain continuous level data, as opposed to other types of sensors that only provide point-level observations. Is this, therefore, the greatest septic tank float switch currently available?
Mechanical Sump Switches
Mechanical sump switches are also referred to as ball float switches in some circles. This sort of septic tank float switch may be found in a variety of applications, including basement sump pumps and sump pumps. Mechanical sump switches are designed to perform a simple set of functions. Or, to put it another way, the on/off operation or functionality of this septic tank float switch variation is straightforward. In addition, this float switch may be used to initiate the pumping of wastewater at different rates.
Horizontal Float Switches
The design of the horizontal float switch varies depending on where it is put or positioned on the circuit board. They’re positioned within the septic tank’s walls and rise and fall in response to the amount of sewage present. Because of this movement, it is simple to regulate the water level within the tank.
Septic Tank Float Switches are Important for the Following Reason…
The septic system, by its very design, provides a crucial function in the treatment of waste water. During the course of a day, when wastewater is discharged into this holding facility, the septic tank allows it to separate into three distinct layers, which are: scum (at the top), effluent (in the middle), and scum (at the bottom). Effluent that has accumulated in the septic tank must now either be evacuated or pumped to a drain field or surface water. A critical component, such as the float switch, must be fitted in order to guarantee that the levels are properly controlled.
When backups occur, the impact of a defective float switch is now felt to the fullest extent.
Common Issues Associated With Float Switch Failure
Float switches fail for a variety of reasons, three of which are discussed here. The existence of moving parts, poor maintenance practices, and selecting the incorrect device or switch for your septic tank are all examples of these issues. Any one of these factors is sufficient to generate issues in its own right.
Presence of Moving Parts
There are certain float switches for septic tanks that contain moving parts.
While they may initially operate admirably, the corrosive and toxic nature of the septic tank environment eventually causes them to fail. Consequently, the moving parts become blocked, and the system fails as a result of the accumulation of debris.
Poor Maintenance Habits
It is possible to have moving parts in some septic tank float switches. However, while they may initially operate admirably, the corrosive and dangerous nature of the septic tank environment eventually causes them to fail. Consequently, the moving parts become clogged, and the system fails as a result of the clogging.
Choosing The Wrong Device For Your Tank
The sort of septic tank float switches that is most appropriate for your individual requirements is influenced by a number of factors, one of which is the purpose of the switch. Seeking expert assistance in the selection of the proper float switch equipment for your septic tank is your best option for success. Septic professionals or technicians have a more in-depth grasp of the components of a septic system. These specialists will often advocate some float changes over others based on their experience.
Septic tank float switches are critical components in septic systems because they help to maintain optimal operating conditions.
More crucial, though, is the requirement for something to operate at peak performance.
How Does a Septic Tank Work?
Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.
How does a septic tank work?
Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.
It’s critical to understand how a septic tank works in order to maintain one.
Let’s take a look below ground and observe what happens in a properly operating septic system, shall we?
Understand that a septic system is a cafeteria for bacteria
Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.
- A layer of sludge settles to the bottom of the container.
- 4.
- Scum is mostly constituted of fats, greases, and oils, among other substances.
- Grease and oils float to the surface of the water.
- (5) A filter stops the majority of particles from reaching the exit pipe.
- The effluent is discharged into the drain field.
- Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.
When gravel is used to surround pipes, water can run into the soil and oxygen can reach germs. The garbage is completely decomposed by aerobic bacteria found in gravel and dirt. 9. Potable water seeps into the groundwater and aquifer system from the surface.
Septic Tank Clean Out: Don’t abuse the system
Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank. However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.
- Drains are used to dispose of waste that decomposes slowly (or not at all). Cigarette butts, diapers, and coffee grounds are all known to cause issues. Garbage disposers, if utilized excessively, can introduce an excessive amount of solid waste into the system. Lint from synthetic fibers is emitted from washing machine lint traps. This substance is not degraded by bacteria in the tank and drain septic field. Bacteria are killed by chemicals found in the home, such as disinfecting cleansers and antibacterial soaps. The majority of systems are capable of withstanding limited usage of these goods, but the less you use them, the better. When a large amount of wastewater is produced in a short period of time, the tank is flushed away too quickly. When there is too much sludge, bacteria’s capacity to break down waste is reduced. Sludge can also overflow into the drain field if there is too much of it. Sludge or scum obstructs the flow of water via a pipe. It is possible for tree and shrub roots to obstruct and cause harm to a drain field. Compacted soil and gravel prevent wastewater from seeping into the ground and deprive germs of oxygen. Most of the time, this is caused by vehicles driving or parking on the drain field.
Get your tank pumped…
Garbage that decomposes slowly (or not at all) is flushed down the toilet. Troublesome substances such as cigarette butts, diapers, and coffee grounds are frequently seen. Solid waste disposal systems, when utilized often, have the potential to overflow their capacity. In the washing machine, lint made of synthetic fibers floats. This substance is not degraded by bacteria in the tank or drain septic field. Disinfecting cleansers and antibacterial soaps are examples of household chemicals that destroy bacteria.
- It is impossible to fill the tank with enough wastewater in a short amount of time without overflowing the tank.
- Sludge that has accumulated in the drain field might overflow as well.
- Branches and bushes’ roots can obstruct and cause harm to a drainage field.
- Most of the time, this is caused by automobiles driving or parking in the drain field.
…but don’t hire a pumper until you need it
Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.
Install an effluent filter in your septic system
Garbage from your home accumulates into three distinct strata. The septic filter is responsible for preventing blockage of the drain field pipes.
Septic tank filter close-up
The septic tank filter is responsible for capturing suspended particles that may otherwise block the drain field pipes. Obtain an effluent filter for your tank from your contractor and place it on the outflow pipe of your tank. (It will most likely cost between $50 and $100, plus labor.) This device, which helps to prevent sediments from entering the drain field, will need to be cleaned out on a regular basis by a contractor to maintain its effectiveness.
Solution for a clogged septic system
If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.
- Keep the effluent filter in place since it is required by your state’s health law.
- Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
- Your filter, on the other hand, should not require cleaning every six months.
- A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
- A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
- Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.
For additional information on what should and should not be flushed down the toilet, contact your local health authority. More information on removing lint from your laundry may be found here.
Get an inspection
The temptation to just remove the filter may arise if your septic system becomes blocked and you have to clean it on a regular basis. It should be preserved. Solids, effluent, and scum are separated into three levels in a septic tank, which allows waste to be separated into three layers (see illustration above). Microorganisms breakdown the particles that settle to the bottom of the tank. It is the scum that floats on top because it is made up of trash that is lighter than water. In the drainage field, the intermediate layer of effluent leaves the tank and is carried away by subterranean perforated pipes.
- Keep the effluent filter in place since your state’s health law mandates it.
- In addition, removing the filter may result in a far bigger (and more expensive) problem down the road.
- Cleaning and unclogging the system would need substantial digging.
- The majority of filters don’t need to be cleaned until the tank is pumped, which occurs every two to five years on average, and then only when necessary.
- Food disposal is an error that many people make.
- Solids can accumulate in a septic tank to levels as high as 50% more than normal.
- More information on what should not be flushed down the toilet can be obtained by contacting your local health authority.
Alternatives to a new drain field
If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.
- If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. A contractor should be consulted about alternative possibilities because the costs might be quite expensive.
Protect your drain septic field from lint
When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.
Don’t overload the septic system
Reduce the amount of water you use. The volume of water that flows into your tank, particularly over a short period of time, can be reduced to avoid untreated waste from being flushed into your drain field.
Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to save water.
Meet the Expert
Water consumption should be kept to a minimum. The volume of water that flows into your tank, particularly over an extended length of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to conserve water.
How to Check Your Septic Panel and Pump Chamber
It is recommended that you inspect your pump chamber once a year to ensure that everything is in proper working order. Follow the 11-step procedure outlined below to complete this task on your own! (Do you require further assistance? Alternatively, you may watch our instructional video below.)
1. Let’s start by inspecting the panel. Make sure the power is on by verifying the power switch to the panel is on.
The following items should be included in this general overview: The electrical box may be seen in the lower left corner of the image below, starting at the bottom of the image. Check to verify that all of the cables are firmly connected before using it. Next, take a look at the lower right corner of the shot, where you can see the discharge pipe for the pump. Check to see if it is operational (valve should be lined up with pipe). It’s now time to have some fun!
FIRST.PUT ON GLOVES!That is one step you DO NOT want to miss. Remove the float tree (the pipe with a pvc handle located upright left in our picture) and pull up the alarms.
Among the items on this broad overview list should be: The electrical box may be found in the lower left corner of the image below, starting at the bottom. Check to verify that all of the cables are firmly connected to the device before continuing. Look to the lower right of the shot, where you can see the discharge pipe of the pump, for your next step. Check to see if it is operable before proceeding (valve should be lined up with pipe). It’s time to have some fun now!
If you don’t hear an alarm, this is cause for concern. Starting at the top, I will explain the floats and how to ensure each one is working.
NOTE: If your water supply is depleted, you may need to replenish it. Fill it up a little with water from a yard hose.
7. Continue testing.
Check that the pump is operating properly by flipping the second float from the bottom upside down and then turning it back around. With your other hand, turn the next float up (which would be the second from the top) upside down while still holding the first float. You should be able to hear the pump start up. As soon as you have confirmed that the pump is operational, just release these two floats. There’s one more float to go. The top float serves as an alert in case of high water. Turn it over down to see whether this is the case.
8. Now is the time to inspect the power cords.
Check to see that everything is securely tied to the float tree and not just hanging free. Zip ties can be used to reattach any stray cables.
9. Securely return the float tree to its holder and coil any dangling cords so that they are out of the water.
Float switches are an essential component of your septic system; they control the operation of your septic pump and alert you when there is a problem, such as when the water level is too high. There are several distinct types of float switches, each of which performs a different function. We will go through this in more detail below. Alarms and pumps are controlled by control duty floats, which are not always directly connected to the pump in question. They are connected directly to the control panel, and the control panel has a relay that activates whatever functions are required.
- To summarize the action, the float rises, closing contacts close and this in turn activates the relay switch, which enables and takes on the load of whatever was previously switched on and off.
- The float switch is responsible for channeling the electrical charge that drives the pump.
- Pump floats are available in a variety of sizes.
- The old pump on the system would have drawn more amps as a result of its age; when pumps age, they begin to draw more amps, which is ultimately what causes them to break down.
- When added to an electrical circuit, float switches enable the sensing of fluid levels on their own without any external assistance from the circuit designer.
- A closed circuit is one in which electricity is able to travel through the circuit’s components and provide power to the devices in the circuit.
- Float switches are activated when fluid levels rise in conjunction with the rise in water level.
The upward orientation of a float switch will normally lead it to shut, although the direction in which a float switch closes will vary depending on the exact float switch being used.
The natural position of a float switch is in the position when it is hanging down.
When the fluid level in a septic system reaches a specific level, the system will normally close a circuit and activate a pump.
The typical position of a normally openfloat switch will cause a circuit to be opened while the switch is in the open position.
When the water level in the system is high, a usually open system will become a closed circuit.
When an excessive amount of effluent accumulates in the tank, a standard septic system will attempt to pump it out.
The closed circuit will activate the effluent pump, which will then raise the wastewater to the desired level once again.
When the fluid level is low, current will flow; when the fluid level is high, current will not flow.
It is possible to utilize this system when the user requires the fluid level in a system to be higher than a specified minimum height.
Mercury is the first sort of mechanism to be discussed.
Unlike the first sort of mechanism, the second type is more mechanical in character.
The ball will roll within the float switch as the level of the fluid changes within the switch.
Float switches are also available in two different configurations: wide angle and narrow angle.
Float switches of this sort can be utilized in situations where a moderate degree of variation in fluid level is acceptable or to be expected.
These sorts of float switches should be considered if the user wishes to keep a more steady fluid level throughout the process.
When the float switch is closed, the effluent pump will begin to circulate the water.
In this way, the level of effluent in your tank can be controlled without the need for the user to look inside of the tank to determine if the pump should be engaged.
It is possible that an effluent pump will fail, causing the level of wastewater in your tank to grow over permitted limits.
A faulty pump, on the other hand, will not empty your tank.
It is possible for the float switch to become stuck in the on position due to a steady current.
This is due to the fact that the float switch has been destroyed and is still instructing the pump to empty a tank that is already empty.
When you purchase a new effluent pump, it is recommended that you replace the float switch to ensure that your system continues to operate properly for a longer period of time.
Float switches that are used in conjunction with a timer may be present.
To adjust the fluid level, an array of float switches, with an override switch, and an alert may be used in some systems. When installing a septic system, it is critical to understand the amount and types of float switches that will be required.
- Float switches are an essential component of your septic system
- They control the operation of your septic pump and alert you if there is a problem, such as when the water level is too high. Each of the float switches has its own function, and there are a few of them available. The details of this will be discussed in more detail below. Control duty floats, which are not directly connected to the pump, control alarms and pumps in some cases. Each of them is connected directly to the control panel, which contains a relay that activates whatever needs to be done on the other end. Control duty floats, also known as sensor floats, have a maximum amp rage rating of five amps and are activated by mercury. When the float comes up, closing connections are made, which in turn activates a relay switch that turns on whatever was turned on and takes over the load. This is a very simple action. It is possible to connect pump duty or pump floats directly to the pump wires since they are intended to handle the amp load of a pump motor when it is operating. The float switch is responsible for delivering electrical charge to the pump. Float pump amp ratings range from 13-15 amps, whereas lock amp rotor ratings range from 50-96 amps. Pump floats are available in a variety of materials. Changing the duty floats on a new pump should always be done when a new pump is installed
- Otherwise, you run the risk of destroying the new pump. Because of its age, the old pump on the system would have drawn more current. As pumps age, they begin to draw more current, which is why they eventually fail. Consequently, they cause harm to the float and it is thus required to change the float switch at the same time as they do the other switches. Fluid level sensors, such as float switches, are an addition to an electrical circuit that allow for the independent sensing of fluid levels. Their principal function is to shut a circuit when the level of the fluid reaches a predetermined height or depth limit. It is possible for electricity to pass through the circuit’s components and power them when it is referred to be a closed circuit. In contrast, an open circuit is one that will not allow current to travel through the components it is composed of. An automatic float switch will be activated as soon as the fluid level is raised to a certain point. In this case, the float switch will be rotated such that it is now pointing upwards rather than downwards. A float switch will normally shut when it is oriented upward, although the direction in which a float switch closes will vary depending on the individual float switch. When a float switch is in the up or down position, there are a few terminology that will inform you whether or not it will close a circuit. A float switch is normally in the position of hanging down. When the fluid level is low, a float switch will hang down from where it is installed. As soon as the level of the fluid reaches an acceptable level, a circuit is closed and a pump is activated in the system. This will result in a significant amount of time spent in the down position while waiting to detect a high level of water in the tank. When the switch is in the typical position, a normally openfloat switch will open a circuit. When the fluid level in the circuit is low, the circuit is essentially switched off. When the water level is high, a typically open system will become a closed system. As a result of its orientation, the generally open float switch is an excellent fit for the vast majority of septic systems. Once too much effluent has accumulated in the tank, a typical septic system will try to pump it out. Due to the growing amount of effluent, the float switch will be activated, causing the circuit to be shut down. It is necessary to use a closed circuit to activate the effluent pump and bring the wastewater back up to the required elevation. A normally closed float switch will behave in the opposite manner to a normally open float switch. Current will flow when the fluid level is low, and it will not flow when the fluid level is high, according to the term “normally closed.” In situations where the user requires that the fluid level in a system be higher than a predetermined minimum height, this technology may be utilized. It is possible for a float switch to close an electrical circuit using one of two broad sorts of methods. In the first instance, mercury is used as a working mechanism. Depending on how much fluid is in the system, the mercury contained within the float switch may shift, which will either open or close the system. It is more mechanical in character than the first sort of mechanism. A ball bearing will be used in a mechanical float switch. The ball will roll within the float switch when the fluid level fluctuates. As a result, the ball will press on internal components of the float switch, causing the circuit to either open or close as desired. Flush switches are available in a number of different configurations, including broad and narrow angles. To engage the mechanism, a wide-angle float switch must be moved a significant distance. A reasonable degree of variation in fluid level is allowed or to be expected when using these sorts of float switches. Wide angle float switches will travel a greater distance before engaging the system than narrow angle float switches. In order to maintain a more consistent fluid level, several sorts of float switches should be considered by the user. Septic systems employ the float switch to detect the level of wastewater present in the tank’s effluent disposal system. As soon as the float switch is closed, the effluent pump will begin to pump. The effluent level will decline as a result, and the circuit will be opened when the level drops to a certain level. Using this system, your septic system can regulate the level of effluent in the tank without the need for the user to look inside of the tank to determine whether or not the pump should be engaged. It is recommended that you replace the float switch in your septic system when you replace the effluent pump. It is possible that an effluent pump will fail, causing the effluent level in your tank to grow over permitted limits. As soon as the water level rises over a certain level, your float switch will attempt to activate the pump. Your tank will not be emptied if your pump is not working properly. Consequently, your float switch may be remained on for an extended amount of time as a result. Float switches may become trapped in the on position as a result of steady current. This condition may need the constant use of your new effluent pump. As a result of the damage to the float switch, the pump has been instructed to empty a tank that has already been emptied. As a result of this circumstance, your pump may overheat or its overall life may be significantly reduced. When you purchase a new effluent pump, it is recommended that you replace the float switch to ensure that your system continues to operate properly for a longer time period. Be aware that many systems necessitate the use of several float switches. Float switches that are used in conjunction with timers may be present. When the fluid level rises to an unsafe level, this override switch will start the pump. It is possible that some systems will employ an array of float switches to adjust the fluid level while also providing override and an alarm. When installing a septic system, it is critical to understand the quantity and types of float switches that will be used.
Septic System Alarm / Float Replacement
The replacement of alarms and floats is critical in the monitoring of the efficiency and integrity of any septic system. The operation of sewage ejector pumps is controlled by a simple float control switch. The float switch activates the pump when the amount of wastewater in the septic tank increases to a certain level. When the tank level and the float are at a low enough level, the switch shuts down the pump and turns it off. A redundant remote float control switch is critical since it may alert you as soon as a sewage problem is noticed, which is really useful.
This will avoid an expensive septic system crisis from occurring.
Advantage Septic Service takes pleasure in identifying problems as early as possible so that they may be “detected and remedied” before more damage is done to the system.
Does Your Septic System Require A New Pump?
A septic tank’s waste and sewage are evacuated from it and discharged into a drain field, either by gravity or with the assistance of a septic system lift pump. In most cases, a septic pump is not required if the waste can flow at a rate of at least two feet per second through the system using gravity alone. Pumps are typically required for septic tanks that are located lower than the drain field and for which gravity is unable to transport and/or force the effluent out of the tank due to its location.
Know If Your System Uses A Septic Effluent Pump Or Septic Grinder Pump
Knowing what sort of pump your septic system is equipped with is critical to the overall operation of the system. A septic effluent pump is a device that transfers waste from a septic tank to a drain field. A septic grinder pump is responsible for the grinding and movement of human waste and toilet paper. Septic tank businesses in Gainesville, FL such as Jones PlumbingSeptic Tank Service can help if you’re not sure what sort of pump the system is using or where it’s located in the system. Our professionals will identify the pump and check the septic system in order to notify you of the procedures that need to be taken in order to keep all components in proper operating order.
How Septic Pumps Work
A septic pump is a sort of submersible pump that is installed in either the last chamber of the septic tank or in a separate chamber outside the main tank of the system. As waste builds up in the chamber, it activates a float switch, which then activates the septic pump. After that, waste is forced up the outflow pipe and into the drain field by an impeller. Installing a septic tank pump alarm is an excellent strategy to avoid having to clean out your septic tank on a regular basis. One of our professionals will connect the float switch to an alarm panel, which will sound if the pump fails for any reason during the installation.
The sewage level continues to build in the absence of a functional pump, and an alarm sounds to alert you that the waste is not being evacuated from the tank. This alarm will ring and notify you if there is a sewage backup in your home.
Maintenance For A Septic Pump
The upkeep of a septic pump goes hand in hand with the upkeep of a septic system in its whole. Never drain or flush any of the following common home objects to avoid the need for emergency septic service and to ensure the pump’s long-term functionality:
- Baby wipes
- Cat litter
- Fats, oils, and/or grease produced by or utilized in the preparation of meals
- Dental floss
- Personal hygiene products
- And Q-tips or other cotton swabs are all recommended.
In addition, avoid using the garbage disposal because this can cause the septic tank to fill up more rapidly and force water into the tank, among other things. If there is an excessive amount of water entering the septic system, it can cause sediments to enter the septic pump, resulting in a probable blockage in either the pump or the drain field. If or when this occurs, contact Jones PlumbingSeptic Tank Service for prompt and dependable septic tank repairs.
Common Septic Pump Issues
Even with proper maintenance, a septic pump can develop a variety of problems over time, including the following:
Noise Or No Noise
There are occasions when it is possible to hear the septic pump operating within the chamber itself. Do not hesitate to contact us for septic service if it appears that the pump is having difficulty or is failing to transport waste effectively.
Leaking Into The Septic Tank
In the chamber, it is possible to hear the septic pump operating from time to time. Do not hesitate to contact us for septic service if it appears that the pump is having difficulty or is failing to transport trash.
Faulty Float
Floats can become stuck open or closed, or they might become damaged as a result of material entering the septic tank. Depending on the extent of the damage, a professional from Jones PlumbingSeptic Tank Service may be able to remove the debris or may need to replace the float entirely.
Burnt Out Motor
If the motor within the septic pump burns out or fails, the pump will be unable to transfer waste, even if the energy is still being supplied to the device, since the waste would be trapped. In most cases, replacing the pump will address the problem.
Installing A New Septic Pump Or System
Jones PlumbingSeptic Tank Service will replace your septic tank if it is essential, and they will also install a new pump. Everything begins with an application, which is needed by the Florida Department of Health. We will always assist you in filling out the application and applying for any permissions that may be required. Our professionals will be pleased to walk you through the procedure and answer any questions you may have along the way.
Septic Tank Service
Jones PlumbingSeptic Tank Service can solve any septic issue, regardless of whether your sewage system currently has a pump or if you’re interested whether installing a pump will increase the system’s overall efficiency. When performing septic tank repairs in Gainesville, our specialists take into consideration the demands of the family or company. Call Jones PlumbingSeptic Tank Service immediately to make an appointment for septic service!
What do I do if My Septic Alarm is Going Off?
In the event that your septic alarm goes off, it may surely create some anxiety and uncertainty; and if you happen to be experiencing this right now, then you’ve arrived to the correct location! Don’t be concerned; it does not necessitate urgent action. Instead, take your time to go through this full essay so that you will be prepared to act now or in the future if the situation arises. What Septic Systems Are and How They Work The alarm works in conjunction with the septic system to alert you when the water level within the pump tank has increased to an unsafe level or has decreased to an unsafe level.
The timer is in charge of regulating the time intervals during which the pump is permitted to pump wastewater into the drainage system.
Thus, during periods of excessive water use, the drain field is kept from getting overflowing, which might cause damage to the drainage system.
A large amount of water is injected into the system in between pumping cycles for whatever cause, and the water has nowhere else to go but back into the system’s pump tank.
Depending on how much water was and continues to be put into the system and how the pump is set up to operate on a timer, it may take many pumping cycles until the water levels are returned to normal. Causes of the alarm going off in the first place
- There is an excessive amount of water being put into the septic system. This is the result of excessive water use, which might be caused by multiple loads of laundry, an excessive quantity of dishwashing, or a disproportionate number of long showers.
- Somehow, groundwater is making its way into the system. If there is an excessive amount of standing water surrounding the septic tanks, whether generated by rain or another source, the water may seep into the tanks and cause the internal water level to rise.
- It’s possible that one of the components of the septic system is malfunctioning. If anything goes wrong with your system — including the pump and floats — the alarm and timer will go off and the septic system will stop working correctly.
The Best Thing to Do If Your Alarm Goes Off Alternatively, if you hear an alert, you should press the red button or turn on the alarm box. The alarm will be turned off as a result of this action. There should be a red light and a green light on the alarm box, which should be situated someplace on the unit. The green light indicates that the alarm is operational and should be left on at all times. It is shown by a red light if the alarm is getting a signal from the pump tank indicating that the water level is increasing above or decreasing below what is expected.
- If the breaker occurs to be tripped, look around the septic tanks to see if there is any standing water.
- It is possible that the red light on the alarm box will go out on its own after allowing the septic system to operate for a couple of pump cycles (which should take approximately 10-15 hours).
- If the red light turns off, it signifies that the system is operating properly and that it only needs to catch up with the extra water that has overflowed into the storage tank.
- To be clear, an alarm signal from the septic system does not always imply that sewage is about to back up into the house right away.
- Do you require septic system repair on a regular basis or emergency service?
- Want to learn more about septic systems?
Septic Alarms, Control Panels, Pump Float Switch, and Control Float Switch from Septic Solutions, Inc.
All septic tank float switches are shipped out the same day, free of charge.
Junior M-NavigatorMercury Activated Pump Switch
For use in emptying applications, this mercury-activated float pump switch features usually open contacts and is suited for use with mercury. When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- Mercury Activated Pump Switch with 90 Degree Wide Angle
- 13 amps, 16/2 SJOW wire, 120/240V, no plug
- Pumps up to 1/2 horsepower at 120V and 1 horsepower at 240V are controlled
- The pumping range may be adjusted from 6 to 36 inches. Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: IN STOCK
| with 10 FooT CordItem20A401 | With 20 FOOT CordItem20A413 |
Do you require assistance in selecting a float switch? Alternatively, you may phone us toll free at 1-877-925-5132.
navigator seriesmechanical Pump Switch
In order to facilitate the emptying of float pumps, this mechanical float pump switch features generally open connections.
When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- Mechanical pump switch with a 90-degree wide angle
- 13 amps, 16/2 SJOW wire, 120/240V, no plug
- 13 amps, 16/2 SJOW wire, 120/240V, no plug Pumps up to 1/2 horsepower at 120V and 1 horsepower at 240V can be controlled
- The pumping range can be adjusted from 6 to 36 inches
- The pump may be used in water and sewage applications. Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem20A001 | With 20 FOOT CordItem20A013 |
Order online at any time, or call our sales department toll-free at 1-877-925-5132 if you have any questions.
Alderon Big SwitchMechanicalPump fLoat Switch
In order to facilitate the emptying of float pumps, this mechanical float pump switch features generally open connections. When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- In order to facilitate the emptying of float pumps, this mechanical float pump switch features typically open connections. Activation of the switch to “ON” occurs when the switch is lifted. Details about the product
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem7368 | With 20 FOOT CordItem7061 |
Septic Solutions® offers free same-day shipping on all float switches, which is a great value.
Alderon Big SwitchMechanicalPump fLoat SwitchWITH 10′ OR 20′ CORD AND PIGGYBACK PLUG
In order to facilitate the emptying of float pumps, this mechanical float pump switch features generally open connections. When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- Mechanical Pump Switch with 90-degree wide angle
- 15 amps, 120/230VAC, 14/2 SJOW wire, Piggyback Plug
- Controls Pumps up to 1 horsepower at 120 volts
- Pumping range may be adjusted from 8 to 22 inches. Utilized in potable water and sewage treatment applications ULListed. Contacts that are built to last
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem7300 | With 20 FOOT CordItem7055 |
Put your trust in the professionals with more than 20 years of expertise in the wastewater business.
navigator plus seriesmechanical Pump Switch
Take advantage of professionals with more than 20 years of expertise in the wastewater sector.
- Mechanical Pump Switch with a 90-degree wide angle
- 15amp, 14/2 SJOW wire, 120VAC, with a Piggy-Back Plug
- 15amp, 14/2 SJOW wire, 120VAC
- Pumps up to 1 horsepower at 120V are under control. Pumping range may be adjusted from 6 to 36 inches. Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem20A102 | With 20 FOOT CordItem20A114 |
We provide the greatest collection of septic goods on the internet, with over 700 different options.
a-navigator high ampmechanical Pump Switch
In order to facilitate the emptying of float pumps, this mechanical float pump switch features generally open connections. When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- A mechanical pump switch with a 90-degree wide angle
- A 25-amp, 12-2/SJOW wire, 120V/240V, and a 10-foot chord
- Pumps up to 1-1/2 horsepower at 120V and 3 horsepower at 240V are controlled. Pumping range may be adjusted from 8 to 28 inches. Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: IN STOCKItem20A301 25 AMP, 120/240V, No PlugControls Pumps Up To 1-1/2 HP At 120VControls Pumps Up To 3 HP At 240V Float Activates To ONIn The Raised Position
SEptic Solutions® offers fast and free shipping on all of their float switches.
Alderon Qwik Pak High AmpMechanical FLoat Switch
The Alderon Qwik Pak High Amp mechanical float switch system is comprised of a junction box with a smart relay and a mechanical float switch system. The float switch communicates with the smart relay, which controls the pump’s on and off states, resulting in a longer float switch life. For use with Grinder Pumps and other high horse power submersible pumps. Specifications of the product
- Switches pumps up to 25 amps or 3 horsepower at 240V
- Breaks BOTH lines while operating at 240V
- Is safe to use with grinder pumps
- 90 degree wide angle mechanical pump switch Pump is activated by a smart relay, which increases the life of the float switch. Pumping range is adjustable from 8 to 22 inches
- Includes 5″x2″x2″ NEMA 4X Junction Box
- Includes Quick Connect Wire Connectors – No Tools Required
- Includes all necessary Junction Box Cord Connectors
- Includes all necessary Junction Box Cord Connectors Designed for use in water and sewage systems
- UL Approved. CSA Approved, Three-Year Limited Warranty
Availability: IN STOCKItem7803 Click To View Larger Image FOR USE WITH GRINDER PUMPS ANDOTHER HIGH HORSE POWER PUMPS25 AMP, 240V,4X Junction BoxControls Pumps Up To 3 HP At 240V Float Activates To ONIn The Raised Position Qwik Pak Specifications
In addition, floats are available in a variety of various lengths of cable. For further information, please contact us.
double M-NavigatorMechanicalPump Switch
For use in emptying applications, this mechanically operated dual float pump switch includes usually open contacts with normally closed contacts. When the switch is in the elevated position, it is triggered to the “ON” position. Dual float switches, as opposed to a single float switch, provide a more versatile pumping range. Specifications of the product
- Mechanical Pump Switch with a 90-degree wide angle
- 15 amps, 14/3 SJOW wire, 120VAC or 240VAC
- 15-foot chord with a Piggy-Back Plug
- 15-foot cord with a Piggy-Back Plug
- Pumps up to 1 horsepower at 120V and 2 horsepower at 240V
- Adjustable pumping range from 2 to 54 inches
- For use in water and sewage applications Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: AVAILABLE IN STOCK
| 120V with plugItem20A505 | 240V with plugItem20A506 |
Put your trust in the professionals with more than 20 years of expertise in the wastewater business.
v-navigator verticalmechanical Pump Switch
This mechanical float pump switch with usually open contacts is ideal for emptying applications and is made of stainless steel. When the switch is in the elevated position, it is triggered to the “ON” position. Due to the fact that this switch only requires vertical movement to operate, it may be fitted in confined locations. Specifications of the product
- Vertical mechanical pump switch
- 10 amps, 120 volts, 16/2 SJOW wire, 10 foot cord with plug
- Controls a vertical mechanical pump. Pumps up to 1/2 horsepower at 120 volts. This product is intended for use in tight spaces. The pumping range may be adjusted from 1 to 6 inches. To be used in water and sewage treatment applications. Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: IN STOCKItem20A201 15 AMP, 120VAC, with PlugControls Pumps Up To 3/4 HP At 120V Float Activates To ONIn The Raised Position
Do you want assistance in selecting a float switch? Alternatively, you may phone us toll free at 1-877-925-5132. All septic tank float switches are shipped out the same day, free of charge.
m-pilot seriesMercurycontrol switch
It features typically open connections and is intended for use with a mercury actuated float control switch to provide high level notifications. When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- Mercury Activated Control Switch with a 10 degree narrow angle of attack
- A 5 amp circuit with 18/2 SJOW wire, 120/240V, and no plug is available. Used in conjunction with a control panel or a high water alarm
- Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem20A701 | With 20 FOOT CordItem20A709 |
Do you require assistance? Please contact us toll free at 1-877-925-5132 for professional assistance.
pilot seriesMechanicalcontrol switch
Normal open contacts are used in this mechanical float control switch, which is intended to provide high level notifications. When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- Mechanically Activated Control Switch with a 10 degree Narrow Angle
- Plugless
- 5 amps, 16/2 SJOW wire, 120/240V, no plug
- No plug
- Used in conjunction with a control panel or a high water alarm
- Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem20A601 | With 20 FOOT CordItem20A609 |
Order online at any time, or give us a call at 1-877-925-5132 to place an order over the phone at your convenience.
ALDERON UNIMAX MECHANICAL FLOATcontrol Switch
The Unimax mechanical float control switch features typically open contacts that are intended to be used for high level alerts or to activate a control panel to empty a tank when the switch is in the open position.
When the switch is in the elevated position, it is triggered to the “ON” position. Specifications of the product
- Mechanical control switch with a 10 degree narrow angle
- 4 amps, 18/2 SJOW wire, 120/240V
- For use with a control panel or high water alarm
- Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: AVAILABLE IN STOCK
| with 10 FooT CordItem7202 | With 20 FOOT CordItem7221 |
All septic tank float switches are shipped out the same day, free of charge.
pilot seriesMechanicalcontrol switch
Normal open contacts are used in this mechanical float control switch, which is intended to be used for low level alerts. When the switch is in the lowered position, it is triggered to the “ON” position. Specifications of the product
- Mechanical control switch with a 10 degree narrow angle
- 5 amps, 16/2 SJOW wire, 120/240V, no plug
- For use with a control panel or high water alarm
- Designed for use in water and sewage systems
- Included is the SST Pipe Mount Assembly. UL Approved. CSA Approved
Availability: IN STOCKItem20A603 5 AMP, 120/240V, No PlugDesigned For Use With Control Panels and High Water Alarms Float Activates To ONIn The lowered Position
Put your trust in the professionals with more than 20 years of expertise in the wastewater business. “The good news is that you had a phone number that was easy to remember and a human voice to speak with! These days, it’s difficult to come by. Some businesses believe they are saving money by not including a phone number on their website or by making it difficult to find. They are incurring financial losses. Many individuals, like myself, prefer to locate products on the internet yet place orders over the phone.
SST FLOAT cLAMP ASSEMBLY
Clamp designed to mount any float switch to apipe.Also see the weights below.Availability: IN STOCKWhen Ordered With A Float SwitchItem60A404 SALE $7.95
Do you require assistance? Please contact us toll free at 1-877-925-5132 for professional assistance.
CableWeight for Float Switch Provides a pivot point for suspended floats
Weight with screws provided securely lock float cable intoplace.Availability: IN STOCKWhen Ordered With A Float SwitchItem60A400-WA SALE $9.50
Order online at any time, or give us a call at 1-877-925-5132 to place an order over the phone at your convenience.
