How Do I Stop My Septic Tank From Backing Up? (TOP 5 Tips)

To keep your septic tank free of backups, be mindful of these following steps.

  1. Never put garbage down your septic system.
  2. Always make sure that your septic tank is biologically active.
  3. Do not plant trees or plants near your septic tank.
  4. Keep the ground above the pipes and sewer lines clear.

How do I stop my septic from backing up?

Septic Tank Backup Prevention

  1. Make sure your septic tank is always biologically active. Don’t use antibacterial soaps and cleaners that drain to the tank.
  2. Never put garbage or any foreign objects into the system.
  3. Avoid planting trees anywhere near your septic lines.
  4. Do not run heavy machinery over sewer lines.

Why does my septic tank keep backing up?

Drains can become blocked with sludge, roots and dirt from broken pipes. In addition, if the ground is saturated because of high water table or heavy rainfall, then the septic tank will not drain and it will back up into the house.

How do you know if your septic tank is backing up?

If your house is starting to smell like a sewer, this is a clear sign you have septic tank backup. If sewage can’t go properly down in the tank, the only place it has to go is back up the pipes.

Can I shower if my septic tank is full?

Only the water would get out into the leach field in a proper system unless you run too much water too fast. The thing to do is to run your shower water outside into it’s own drain area, but it may not be allowed where you are. Used to be called gray water system.

Can a lot of rain cause septic tank backup?

It is common to have a septic back up after or even during a heavy rain. Significant rainfall can quickly flood the ground around the soil absorption area (drainfield) leaving it saturated, making it impossible for water to flow out of your septic system.

Will toilet flush if septic tank is full?

Toilets Flush Slowly When your septic tank is excessively full, your toilet may start acting odd. You might find that your toilet doesn’t fully flush or flushes very slowly and odd noises occur when you flush your toilet. These noises usually sound like gurgling or bubbling.

Will a flooded septic tank fix itself?

Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.

How do I know if my drain field is failing?

The following are a few common signs of leach field failure:

  1. Grass over leach field is greener than the rest of the yard.
  2. The surrounding area is wet, mushy, or even has standing water.
  3. Sewage odors around drains, tank, or leach field.
  4. Slow running drains or backed up plumbing.

What are the signs that your septic tank needs to be pumped?

Common Signs You Need Septic Tank Pumping Services

  • Slow or Frequently Clogged Drains. Since your septic tank is connected to the entire network of drains throughout your home, your sinks, showers, and even toilets can exhibit signs of a problem.
  • Sewage Backup.
  • Regular Gurgling Noises.
  • Strong and Pungent Odors.

How many loads of laundry a day are safe to do with a septic tank?

Spread Out Laundry Loads These use less water which puts less stress on your septic system. Regardless of the type of appliance you have, you should still spread out your loads. Instead of doing several loads in one day, consider doing 1 load per day or space out 2 loads if you must do more in a single day.

What to do after septic is pumped?

After you have had your septic tank pumped by a trusted septic company, there are some things you can and should do as the septic system owner.

  1. 1) Get on a Schedule.
  2. 2) Take Care of the System.
  3. 3) Know the Parts of Your System.
  4. 4) Check Other Possible Issues.

What to do if your septic system backs up?

The steps you should take if your septic system begins to back up. Make sure you follow these procedures to ensure that the problem is resolved!

1. Stop Running Water

When your septic system begins to back up, the first thing you should do is turn off the water supply. The majority of people are unaware that when sewage begins to flow into their home, it is because the water they are using has nowhere to go. Simply turn off the water supply and the flow of sewage will be stopped immediately! Until the problem with your septic system is repaired, refrain from using the bathroom, taking a shower, doing dishes, or doing laundry. In order to use the shower or the bathroom, you will be need to go to a neighbor’s house or a local leisure center.

Once the switch is turned on, the light will continue to flash, but the sound will be silenced.

2. Check the Water Level in Your Septic Tanks

After that, you need to figure out where the problem is stemming from. Perhaps there is no problem with your septic system at all, but the plumbing between your house and the tank may have been blocked as a result. In order to accomplish this, the amount of water in your septic tank must be checked. We recommend that you hire a waste-water specialist to take care of this for you, as entering your tank may present a risk of injury or death. If you decide to do the inspection yourself, keep in mind that tank lids can be heavy and may require specific tools to open properly.

Normal Operation Level:

It is difficult to define what constitutes a “full” septic tank. The normal operating level will look somewhat like the image on the left of this page. In order for the “riser” to ascend to the surface, there should be no water present. The sewage connection from the home to the septic tank should be checked for damage or obstructions if your septic system is backing up yet your septic tank has a normal operating level, such as the one illustrated in the illustration below. However, while John Todd Co.

When it comes to sewage line scoping, a camera tiny enough to penetrate your pipes and check the problem regions is available as a service from our company.

Overfull Level:

It is necessary to have your septic tank pumped if you open the lids of your septic tank and see water pouring into the riser, as shown in the illustration to the right. Always be sure that whomever is pumping your septic tank is keeping an eye out for any backflow from the soil treatment area (for gravity systems). A failing leach field will be evident if you detect water gushing back into the tank from the leach field for an unusually long period of time. Septic tank pumping is a service provided by John Todd Co., and the company even provides an after-hours emergency pumping service for customers.

To use hot water, turn on all of your sinks, showers, and tubs, and flush a toilet two to three times, as needed.

Allow for approximately 5-10 minutes of continuous running of the sinks. This forces anything that may have become lodged in the pipes between your tank and your house during the back up to the surface of the water.

3. Follow Up with Repairs

Pipe cleaning and septic tank pumping are merely short fixes for a long-term problem. Make sure you follow up on any repairs that have been recommended to you. Your sewage line being clogged might be due to a broken or deformed pipe that has to be repaired or removed and replaced. It will be necessary to have a new leach field created if your existing leach field is not absorbing water. You can contact us at any time if you have any queries or need assistance with the situation. Call (303) 791-0520 to talk with a member of the John Todd Co.

Septic Tank Backup: Warning Signs & How To Fix It

It is no one’s desire to rip up their grass in order to pay for a pricey septic tank repair. Having a thorough understanding of your tank and a sharp eye for difficulties implies that you can foresee problems and the entirety of your system’s renovation.

How Does A Septic Tank Work?

A basic septic tank is composed of two components: Watertight subterranean tank for storing sludge and wastes 2) and a drain field, which treats and filters water as it returns to the soil after being drained. When everything is running correctly, this mechanism keeps potentially hazardous material in situ and only allows treated water to escape. All that is required is that the waste be pumped out every few years, and the system will continue to operate properly. However, if you’re reading this, you’re probably aware that this isn’t always the case.

Why Do Septic Tanks Backup?

A backed-up septic tank is a major headache that can occur for a variety of reasons. Some events are under your control, while others may occur at any time. Septic tank backlog can be caused by a variety of factors, some of which are listed below: Flooding: When heavy rains soak the earth around a septic tank, the tank may have a difficult time emptying correctly, leading to flooding. The trash and the clean water will mix together and run out simultaneously if there is no dry soil to absorb the pure water.

  1. Tanks are available in a variety of sizes.
  2. Unsatisfactory Installation: Unless you built your home from the ground up, you may not be aware of who constructed your septic system or how old it is.
  3. Before purchasing a new house, make sure to get the septic tank inspected.
  4. Only rubbish and toilet paper should ever be flushed.
  5. If you’re not sure whether anything is flushable, look to see if the box says “septic safe.” If it doesn’t, toss it in the garbage!
  6. Growing tree roots may even cause obstructions in pipes as they creep into cracks and crevices.

Pressure on the Tank: If cars are passing over your septic tank, the pressure created might cause pipes to rupture. Make sure your tank is well marked and that any prospective traffic is kept away from it.

Warning Signs of a Backed Up Septic System (And What to do About It!)

It might be difficult to determine the signs of a backed-up septic tank at first glance. At first sight, you could dismiss any of these warning indicators as being inconsequential. However, it is critical to take all of these warnings seriously and to conduct an investigation into the matter. Identify whether any of these warning indicators are present in your house.

  • Was it a while ago that you had your septic tank drained and cleaned? In the absence of a regular cleaning routine, you may notice sewage backups in your toilet as well as slow draining sinks and bathtubs in your bathroom. This is an indication of blockages. Without frequent pumping, a septic tank fills up with solid waste and enables contaminated water to pass through
  • However, the unclean, polluted water has nowhere to go and must be pumped out regularly.
  • Your driveway or sidewalk may be gradually rising due to tree roots if you see bumps in the road or uneven surfaces. There are a few different approaches you may use to deal with roots in your septic system. It is the most lasting method if you are ready to part with the tree, removing it totally, removing and replacing it with new pipes. Newer, stronger plastic pipes are designed to withstand tree roots and are an excellent alternative to metal pipes. Alternatively, you may pour a root-killing solution down the drain to prevent future development.
  • In one spot of your yard, do you have a clump of vivid green grass growing? If it hasn’t rained in a while, have you seen pools of water in unexpected places? Your septic system’s leaky pipes are clearly visible in these conditions.
  • It is a strong indication that you have a septic tank backlog if your home begins to smell like a sewer. If sewage cannot adequately drain down into the tank, the only option is for it to flow back up the pipes.

If you have seen one or more of these warning signals, it is imperative that you take action before the issue spirals out of control, since there are serious implications to having a clogged septic system.

Dangers of a Backed Up Septic Tank

A clogged septic tank may cause far more serious problems than just a puddle of water in your shower. Septic backflow is a serious health threat for you and your family, since it is a carrier of illness. In sewage, drug leftovers, human waste, fungi, viruses, and bacteria can all be found in large quantities. If you see any sewage backup bubbling into your house, call for expert aid in disinfecting your home. When you have a clogged septic tank, water damage is a definite possibility. Septic tank leakage in your house may severely harm your flooring and walls, as well as the rest of your property.

Untreated sewage from your clogged septic system can have far-reaching consequences for the ecology surrounding your property.

If you see signs of a clogged septic system, you should either attempt to fix it yourself or hire a professional like All Dry USA to do the work for you.

How To Fix Septic Tank Backup

The most effective technique to repair a septic tank is through regular maintenance. If you have a big family, make sure you get your system pumped every 3 to 5 years, or more frequently if necessary. Regular pumping will hopefully save a giant backhoe from ripping up your yard and repairing a sewage tank that has broken down on you. Check to ensure that your float switch is functioning properly. This will automatically turn off the system and shut off your water supply to prevent a potential backup from occurring.

Snakes may be obtained at any hardware shop and are available in a variety of sizes to accommodate the size of your pipes.

Calling (866) 313-0458 at any time of day or night to speak with All Dry USA about your backed-up septic tank is a terrific answer.

As a result of our more than ten years of repair experience, we haven’t come across an obstruction, a pipe, or a septic tank that we couldn’t clear out and put back in working condition.

Ben possesses a wide range of specialized qualifications and certifications in the fields of repair and building. Ben Suiskind’s most recent blog entries (See all of them)

Steps to Take When Your Septic Tank Backs Up

Septic tanks are a way of life for many people in rural regions, and for good reason. The most of the time, they are out of sight and out of mind. That is, unless something goes wrong and the septic tank begins to back up into the house. Then there’s an issue, and then there’s a big mess. In addition, there is the matter of what to do. If your septic tank does begin to back up, there are a few things you may take to resolve the situation.

See also:  How Much Cost For Septic Tank Pumping?

How a Septic Tank Works

The first step in resolving a septic problem is to have an understanding of how a septic tank truly operates and functions. A septic system is composed of three components:

  1. Your toilet, sink, and tub all have lines or pipes that go from them that use gravity to transport waste outdoors to a holding tank. Essentially, the holding tank serves as a bacterial chamber for breaking down solids. Then there’s the disposal field, which distributes liquids such that they may be absorbed into the earth over time. In the event of a blockage or obstruction in any one of these components, a septic backup will occur.

Types of Septic Tanks

There are three basic types of septic tank materials: concrete, plastic, and metal. The first is made of concrete, the second of fiberglass, and the third is made of polycarbonate plastic. The difference between them is the pricing range they provide as well as the strength or durability of their products. All of them do the same duty of collecting waste and separating solids from liquids, but the materials used in their construction have no effect on backup. It is the overall design of your septic tank “system” that makes the most impact in the frequency of septic tank backups.

One is straightforward and relies on gravity to empty your waste into a holding tank.

Because it is pressurized, the second septic system is more complicated than the first.

The spilling liquid is then gravity-fed into a second, smaller tank located downstream of the original.

Steps to Take When Fixing a Septic Tank

Now that you understand how septic systems function and whatever type you have, you must identify the source of the problem and take the necessary actions to correct it.

  1. Isolate the source of the obstruction. To begin, open the tank lid and check the amount of the liquid within the tank. If the tank level is low, this indicates that there is a barrier upstream between the home and the tank. If the tank is completely filled, you’ll have a downstream problem
  2. Look for a power interruption or a jammed float switch to rule out. Usually, restoring one of these will restore your system to its previous state
  3. Inviting a professional with the skills and instruments to externally remove the obstruction is a good idea. This involves the use of cameras to determine the exact source and position of the obstruction, as well as augers to remove the impediment.

Septic Tank Backup Prevention

The most critical action you can take is to avoid a septic tank backlog from occurring in the first place, as described above. Here are some recommendations for prevention:

  • Always check to see that your septic tank is still biologically active. Use of antibacterial soaps and cleansers that leak into the tank is discouraged. Never use the system to dispose of rubbish or other alien things. By their very nature, human waste is biologically active, but raw food scraps are not. Garburators are extremely dangerous criminals. Planting trees in close proximity to your sewage lines is not recommended. It is well known that tree roots will search for water and nutrients within sewage pipes. You should avoid operating heavy machines over sewer lines since they will puncture and obstruct them in no time. Moreover, lines are readily crushed and damaged

With a little forethought, you can ensure that your septic tank continues to function for an extended period of time with little or no maintenance. That’s exactly what it’s intended to do.

5 Things To Know About Septic System Backups

If you’re the kind that like to do things himself, fixing a leaking pipe every now and then is OK. However, if the problem is more complicated than a leaking pipe or a blocked toilet, it is not a job that should be attempted by the homeowner. Septic system backups are extremely dangerous, and you should contact a septic repair firm as soon as possible to get the situation resolved. The probability of sewer backups is one of the most difficult challenges that homeowners will have to deal with.

This is one job for which you will want the services of a professional. When it comes to dealing with septic systems, you need to be skilled and knowledgeable about how the system works, where the drain field is located, and how the piping from your home to your septic tank is connected.

Can the septic system backup into my house?

Yes, it is possible. Sinks and bathtub drains that take a long time to empty may be your first and only warning indicators. If this appears to be happening on a regular basis, it might be an indication of something more serious to come. If you notice murky, black, or dark-colored water backing up into your toilets, bathtub, or sinks, it might be sewage, and you should call a septic provider to come out and inspect the situation immediately. If it turns out to be a backup problem, they will have the necessary instruments and experience to correct it without putting you or the houses around you in any danger.

What causes this to happen?

  • Generally speaking, the reasons of septic system backups are the same as those that cause sewage line blockages. Tree roots that have grown underground have found their way into the crevices in the pipes and have continued to grow, creating an impediment. Foreign objects in the system: It is possible that non-flushable goods such as feminine hygiene products, baby wipes, diapers, or other similar items were flushed through the system and became trapped
  • Using a trash disposal: Although a garbage disposal is intended to flush the contents of the disposal into an open sewage line, if the food is not broken down small enough, it might become lodged in the pipes, causing a clog. Overflow can also be caused by a large amount of water being pumped into the system at the same time, such as that produced by dishwashers, washing machines, and frequent showering. This is referred to as an overload, and it may be prevented by spreading out your water consumption across appliances and showers. For example, you may run your dishwasher at night, shower in the mornings, and wash your clothes once or twice a week as an example of spacing your tasks. This will prevent an excessive amount of water from being pushed into the system, which might cause it to overflow and push back into the home

5 Warning Signs You Shouldn’t Ignore

If you see one or more of these five signs, your septic system may be failing. If you only have the first of these indicators, it may not be a significant worry, but if you have more than one of these signs, you most likely have a serious issue.

  1. Drainage that is clogged
  2. A foul odor emanating from your yard
  3. Reverse osmosis of water into the tub, shower, or sinks
  4. The presence of water near the septic tank’s lid
  5. A area of greenery or a stretch of land that has a lot of water

Can this be prevented?

You may avoid septic system backups by making sure that no toys or other things are flushed down the toilet. A sink strainer will also prevent a large amount of food leftovers from being flushed down the toilet. You may also avoid overflowing toilets by spreading out your water consumption, as previously indicated. Additionally, make certain that your system is pushed out at the suitable moment. Septic systems should be pumped out every 3 to 5 years in order to prevent issues from developing.

Posts from the recent past

What Causes a Septic Tank to Back Up With Your Home System?

Consider the following subject, which may cause chills to run up and down your spine.and for good reason! The most common reason for this is a clogged septic tank. That one seemingly simple, innocent query has elicited as many and different responses as the people who use the facilities that drain into septic tanks. Let’s have a look at a couple of them in one go.

Answer1.

When a septic tank backs up, it is because it is exhausted from constantly moving ahead. Haha. You got me on that one, didn’t you? Okay, so I couldn’t help but crack a corny joke here and there.

More serious now:

When dealing with a septic backup, one of the first things to assess is if the backup is caused by the Septic Tank itself, or whether it is caused by a blockage in the plumbing lines. Customers who are experiencing a backup may contact in to have their septic tank pumped, only to find that once our personnel pump the septic tank, the backup has returned to its previous state. As opposed to a genuine backup in the sewer system, blocked plumbing lines are more frequently the culprit. The following are some of the most typical reasons for clogged plumbing/drainage lines leading to the septic tank:

Tree Roots

This is one of the most typical problems that drainage lines encounter all across the world. We all adore those beautiful lawns that are shaded by a large, imposing old oak or maple tree, don’t we? They’re just stunning. While it is true that the upper half of the tree, which is easily seen and appreciated, is lovely, these trees have a dark counterpart underground.a vicious root system that is constantly on the lookout for.water! Tree roots have an extraordinary capacity to detect the presence of water from tremendous distances, and they will go to great lengths to penetrate anything that comes between them and the precious water that they so desperately require to survive.

  • Once you’re inside, two things start to happen at the same time.
  • These roots continue to develop and proliferate within the pipe, soaking up the nutrient-rich water and returning it to the tree.
  • Despite its small size, it possesses incredible strength.
  • The use of a high-powered water-jetting equipment and/or a mechanical augering cutter tool can be used to address minor root infestations in the home.
  • Major infestations will need the excavation and removal of the infested pipe, followed by the installation of a new pipe to remedy the damage.

When doing these repairs, special attention must be paid to the connecting points because even the smallest break will result in a recurrence of the original problem over time.

Other common system damage causes include:

Never, ever do something like this. Grease should be poured down the sink. Period. This is one of the most reliable methods of causing a backup in your plumbing lines and septic tank. When grease comes into touch with water, it will coagulate and solidify. Once within your pipe, it will solidify into a stiff material that can eventually block your pipes completely, causing overflowing toilets, sinks, and showers to occur. Have I said everything I wanted to say? Here are a couple of more things you might not have considered.

  1. They have a bad propensity of producing backlogs in the system.
  2. Baby wipes should not be flushed.
  3. There will be no condoms.
  4. They will eliminate the live bacteria that is necessary for your septic tank to function correctly.
  5. And yes, we have witnessed each and every one of these frightening scenarios.as well as many others.

Improper plumbing installations

When installing plumbing, an inexperienced plumber or a do-it-yourselfer may make the mistake of installing piping with inadequate fall, also known as drop. When the water in a flush runs too slowly, the solids settle to the bottom of the pipe, where they may be seen seeping away as the water seeps away. By the time the next flush rolls along, the solids have dried up and become adhered to the bottom of the pipe, generating a buildup that eventually results in a blockage and a backlog of water.

Another cause of backups:

These are intended to keep your leach field from being overloaded, hence avoiding the need for costly septic system repairs. Their purpose is to keep all particles contained within the septic tank and to enable only water to drain to the leach field or drain field. To ensure that these filters continue to perform properly, they must be cleaned and maintained on a regular basis. Failure to clean and maintain your effluent filter will eventually result in.you guessed it.a clogged effluent filter.

One final common cause for Septic damage:

Extremely heavy rains or extended periods of wet or rainy weather, particularly in areas where groundwater and surface water are not adequately redirected and drained away from your septic tank and leach field, can cause flooding in your septic system. The long-term solution to this problem is to have adequate drainage work completed to guarantee that your septic system is kept protected from rainwater run-off. Give us a call at Shankster Bros. to find answers to all of these issues and many others!

How to spot the most common septic back up problems

In the same way that you maintain the rest of your home, your septic system requires routine maintenance.

If the system is properly maintained, it should last for many years with just minor malfunctions. In contrast, when the system ages and maintenance is not performed on a regular basis, there are concerns which may arise and cause a backup inside your septic system.

Here are the signs of a problem with your septic system and what to do to if you experience any of these problems!

  1. Flooding is occurring in the home due to the backup of water and sewage from toilets, sinks, and other drains. Drains take a long time to drain their contents. In the vicinity of the septic tank, there is standing water or areas of excessively wet terrain
  2. Heavy scents have been detected in the vicinity of the septic tank. Even in the midst of a drought, the bright green grass surrounding the tank is apparent.

These are only a few indications that your septic system need maintenance, and that you should contact a professional plumber to promptly identify and correct the problem. This can save you money in the long run by preventing costly repairs.

But how can you fix a septic back up yourself?

One thing to keep in mind is that a backed-up septic system may be dangerous to you, your family, and even animals in the house or neighboring regions if not addressed immediately. A septic failure may happen to anybody at any time. It occurs when untreated sewage is discharged and transferred to a place where it is not intended to exist. This can result in sewage finding its way into groundwater, surface water, or even lakes and other bodies of water – all without you being aware that anything is amiss!

See also:  How Much Does It Cost To Install A Septic Tank In Tallahassee? (Solution)

When you notice a drain is slower than usual or has even stopped all together, it’s time to find where the problem is and how you can fix it.

  1. Isolate the source of the problem. Begin by taking a peek inside the tank and determining the level of the contents. If the tank level is low, the obstruction is located between the house and the tank. A clogged septic tank indicates a “downstream” problem
  2. Is the electricity to the septic tank operational? If not, it is recommended to get it serviced. What’s the deal with your float switch? Is it up and running properly? If you reset both of these components, your system may be able to get back into gear. If you are unable to diagnose the problem on your own, a professional can aid you through the use of cameras and other specialized instruments to assist you. In addition to identifying and resolving the problem, they will also resolve the issue.

Snaking the drain is a simple remedy that may be undertaken by the average person. Unclogging a drain using a snake is one method that experts employ to clear a clogged pipe. A snake may be obtained at any hardware or home improvement store with relative ease. Inspect and clear up clogged drains using the tool, which will efficiently push the blockage from the drain and free up the pipes. If this does not resolve the issue, it is possible that a more serious problem is causing the sluggish drain.

To keep your septic tank free of backups, be mindful of these following steps.

  1. Never flush waste down the toilet or into the septic system. The septic system is intended solely for the disposal of human waste. Because it is biologically active by nature, it will decompose over time, whereas rubbish will not decompose at all. Always check to see if your septic tank is biologically active before using it. Using antibacterial soaps will actually destroy the bacteria that is preventing your septic system from being clogged in the first place. Instead of washing your hands with antibacterial soap, use it to clean the tank itself. Planting trees or other plants in close proximity to your septic tank is not recommended. Make sure to keep an eye out for tree roots if there is any existing landscaping near the tank. Due of their need to find water and nutrients contained inside the pipes, they might cause punctures to occur within the pipes. Keep the area above the pipes and sewage lines free of obstructions. Heavier gear can crush and ruin pipes, causing significant damage to your septic system.

The Water Out expert clean up crews are ready to assist you if you find yourself in the position where your septic tank has become clogged and cleaning is required immediately. We have received extensive training in proper clean-up procedures to keep diseases away from your family. Our professionals are trained and qualified to remove any and all garbage from your residence. It is critical that you delegate the cleanup of sewage to specialists from the Water Out team in order to ensure your own safety!

No words can express how strongly we believe that homeowners should avoid attempting to clean up raw sewage on their own.

How To Handle Septic System Backups A-American Septic Service

When you flush the toilet and immediately hear the gurgling of water from the tub or sink, it’s never a good day. It’s critical to precisely assess the location of the problem because fixes might differ depending on where and what the problem is in the first place. We’ll look at how to deal with septic system backups and obstructions in this section. There are a multitude of factors that might contribute to the failure of a sewage system. Something as easy as flushing a toy or an item of clothing down the toilet can produce a clog in the system, resulting in foul odors or worse in your house.

First Warnings That The Septic System Is Backing Up

Ordinarily, the first signs of a failing septic system are foul odors within the home; slow drains; backup of water in toilets, tubs, and sinks; or the presence of standing water on the ground outside the home.

It is vital to take the necessary measures to determine the source of the problem, as breaking up the yard with a backhoe is a costly option.

Septic vs. Plumbing Problems

If you are experiencing a plumbing problem, the first thing you should do is determine whether you have a septic system problem. The best approach to determine if you have a single drain problem or a clog that affects the whole home or building is to test some of the other drains. Unless the problem is limited to that one drain in the kitchen and everything else in the house is working properly, you most likely have a blockage in the plumbing system within the house. If, on the other hand, all of the drains in the home are sluggish to drain or are backing up, you may have a problem with the whole wastewater disposal system.

Steps To Fixing A Slow Or Blocked Drain

First and foremost, you must determine whether there is a clog or obstruction within the structure. Regardless of whether the structure is a home or an apartment complex, you’ll need to verify the operation of all of the drains in the building. If the main drain is blocked, the higher floor drains may continue to work, although this is not always the case. Because of this, when the upper floors use their water, the contents of the tank can back up into your ground-floor flats. If all of the drains in the basement levels are functioning well, but there is one drain or toilet that is not functioning properly, you have a blockage at that location.

If it has always been a little sluggish, it might be due to a tiny obstruction.

As previously said, if the problem affects all of the drains in the building, you are most likely dealing with a main line issue that is preventing waste water from reaching the septic system.

Septic System Blockage Clearing

If you are feeling handy, there are a few things you can do for yourself before calling in a professional to assist you. Traps are seen in sinks and bathtubs. Traps are a U-shaped curve in the plumbing that allows it to travel down in one piece.

DIY Septic System Blockage Clearing

Step1 – Locate the PVC pipe by opening the cupboard under your sink and looking inside. You’ll see a sequence of links as you scroll down. The pipe that runs from the bottom of the sink, down to a U-shaped part (the trap), and then another elbow junction that links the trap to the wall drain is known as the sink trap pipe. Placing a bucket beneath your work location will allow you to more easily untie the connections to the trap. Make sure you’re not wearing your favorite t-shirt since the water may start to drain.

If you don’t have access to a garden hose, attempt to clear the obstruction with a plunger rather than allowing it to just run down another drain.

In rare cases, if the water level is not too high, it is possible to pour some hot tap water into the tank to cause a brief surge in pressure that will force the blockage loose.

Kinetic water rams can also be used to clear these obstructions, but the majority of people do not have one of these laying about the house. These equipment need a lot of skill, so enlisting the help of a professional may save you a lot of stress as well as potential harm to your plumbing system.

Professional Septic System Blockage Clearing

Obviously, if you’ve gotten this far and it isn’t depleting you, it is unavoidable that you will require some assistance. A specialist will be able to assist you in determining whether or not you have a drain waste vent problem or whether or not the blockage is located outdoors. This is accomplished by a professional by opening either fixture drains or the whole-house drain, which is where the waste water from the entire house escapes. It is the pros’ tools, expertise, and understanding that will allow them to either correct the problem or provide you with further information about why your system isn’t operating properly.

What exactly is required may vary depending on the nature of the problem you are experiencing with your system.

Checking The Drain-Vent System

When you have slow-draining fixtures, this is a regular problem to encounter. In order for the system to function properly, air must be drawn back into it through the vent. On rare occasions, birds may construct nests in the drain vent, or other small creatures may climb into and become trapped in the pipes. It is possible for these vents to get frozen if you live in a particularly cold climate, and this will prevent them from functioning properly.

Damaged Piping Outside

Having slow-draining fixtures is a regular source of frustration. The system requires air to be re-introduced, and the vent facilitates this process. Other tiny creatures may crawl inside and become entangled in these pipes on occasion, either as a result of bird nests or other obstructions. It is possible for these vents to get frozen if you reside in a particularly cold climate, which will prohibit them from functioning properly.

Snaking The Line

Professionals will snake the line leading to your septic system in an attempt to determine whether and where you may have root damage, blockages, or other problems in your line by looking for signs of failure. This will either remove the obstruction or restore your ability to operate, or it will assist the professionals in determining the location of the damage or blockage. Instead of digging up your entire yard, this will assist them in determining where they should dig.

Failed Septic Systems

If all of the pipes, drains, vents, and traps are free of obstructions, the most likely source of the problem is the septic system itself. An assortment of factors may contribute to this. Control panels wear out, toilet paper that is not septic-friendly is used, leech fields become blocked, and a slew of other issues arise. Professional septic firms can assist you in determining exactly what is wrong with your system and in determining an economical solution to get it back up and running. Depending on the architecture of your system, there may be a range of expenses associated with repairing or replacing your malfunctioning sewage disposal system.

Phoenix Area Septic System Repair

A septic system is the most likely source of sewage backup if all pipes, drains, ventilation, and traps are unobstructed. Any number of factors might contribute to this. Control panels wear out, toilet paper that isn’t septic-friendly is used, leech fields become blocked, and a slew of additional issues arise. The experts at professional septic firms can assist you in determining exactly what is wrong with your system and in determining an economical solution to get it back up and running.

In certain cases, fixing or replacing your broken septic system may be more expensive than just replacing it, depending on its design.

About the Author

In the absence of professional plumbing training, it can be difficult to evaluate whether or not you are experiencing problems with your septic tank. If you live in a rural region, your septic tank may be your only means of treating and disposing of the waste generated by your household. The waste from your home is dumped into a septic tank leach field, which is also known as a septic drain field, once it has left your home. An underground facility designed to remove contaminants from the liquid that emerges after passing through the septic tank, the septic tank leach field is also known as a septic tank treatment field.

Fortunately, there are various symptoms that suggest that the leach field of an aseptic tank or the septic tank itself is malfunctioning.

  • There is backup in your home’s drainage system or toilets. Backups and obstructions are most commonly caused by a septic tank that hasn’t been emptied in a long time, according to the EPA. A failed leach field in your septic tank means that the water that leaves your home will not be handled and treated at all. Your drains will become clogged as a result. The toilets in your home are taking a long time to flush — If all of the toilets in your home take a long time to flush, it might be a sign that your septic tank is overflowing. Due to the fact that this sludge is not being handled by your drain field as efficiently as it should be, it is creating delays in your toilet flushing. It takes longer for sinks and baths to drain now than it used to – A clogged septic drain field may be to fault if your sinks or bathtubs aren’t emptying as rapidly as they should be under normal circumstances. A septic drain field replacement may be necessary if you find yourself waiting an excessive amount of time for the tub to drain after a bath or for the sink to empty after cleaning dishes. It is discovered that there is standing water near your drain field or septic tank – The presence of standing water near your drain field or septic tank is the most obvious indication that your septic tank has been flooded and that your septic leach field is failing. Water remains in your septic tank after it has been cleaned and processed, and this is what causes standing water in your yard. Your septic tank and drain field begin to smell foul near your house or business — Both your septic tank and septic drain field should be free of foul odors, both outside and within your home. Carbon dioxide, methane, and hydrogen sulfide, all of which may be present in household garbage, are responsible for the scents you are smelling. In the vicinity of your leach field, you may notice a strong rotten egg stench, which may signal that sewage is seeping. Your health and safety, as well as the health and safety of others, are at risk as a result of this. You should contact a septic drain field replacement company as soon as possible at this point.

Resources:

  • What is the best way to determine when to empty a septic tank? How to Unclog a Drain Pipe (with Pictures)

Signs That Indicate you Need an Immediate Drain Field Replacement

So, how can you determine whether you require a septic drain field replacement rather than only a repair? The following are indications that you require an emergency drain field replacement:

  • Septic tank failure due to a failure to clean or pump waste out of the tank on a regular basis – If you don’t follow your septic tank cleaning plan, you run the danger of having a septic drain field replacement sooner rather than later. Maintaining your septic tank and having it examined at least once every three to five years helps ensure that your drain field is functioning correctly. The number of people living in your home, whether or not you have a garbage disposal, whether or not you use water softeners, how many guests will be in your home at the same time, how often you do laundry, and whether or not you have a sewerejector pump all influence how often you need to have your septic tank pumped. This one is rather self-explanatory: you have broken pipes in your drain field. If your plumber is checking the pipes leading to and from your leach field and detects a break in the pipes, you will need to have a septic drain field replacement performed immediately. In the event of a septic pipe break that cannot be repaired, new pipes or a complete system may be required. Lack of oxygen in the septic tank as a result of a significant amount of grease – An excessive amount of grease in your septic tank system results in the formation of a “scum” layer. It is possible that your leach field is being replaced. Following an overabundance of grease being dumped into your septic tank, the drain holes and piping leading to your drain field will get clogged, necessitating the replacement of the whole system. Tree roots placing strain on your drain field piping — When tree roots begin to grow into your drain field piping, it might spell doom for your drainage infrastructure. These tree roots have the ability to develop swiftly and will seek out a source of water as soon as they can. If the pipes delivering water to your leach field are large enough, the tree roots will eventually find their way there, perhaps rupturing the piping system. Compaction of soil caused by heavy machinery or automobiles near your septic tank drain field – Drain fields that are close to air pockets in the soil surrounding them. When heavy equipment or automobiles are parked or put on top of or near the leach field, it can cause issues for the system to malfunction. A compacted soil environment encourages water to collect near your septic field.
See also:  How Important Is A Septic Tank Inspection? (TOP 5 Tips)

Common Septic Tank Problems and How to Fix Them

You probably don’t give much thought to what happens to your extra water after it has been flushed down the toilet unless anything starts to go wrong with the plumbing. It is critical that you do thorough septic tank repair on a regular basis in order to minimize costly damage. You must first locate your septic tank before proceeding with any further steps. Due to the complexity of your septic system’s operation, and the fact that much of it is underground, issues with it can often go undiagnosed for extended periods of time.

Most likely, one of these five factors is to blame for any septic tank issues you’re now experiencing.

Clogs in Your Septic System

In order to determine whether or not you have a septic tank problem, remember back to the last time your tank was cleaned. Septic tanks accumulate waste over time, and grey water drains through your septic tank to drain pipes that are buried underground in the earth in your yard. In the event that your tank becomes overflowing, you may begin to notice that your drains are becoming slower and that your toilet is becoming backed up. Each and every source of water in your home passes through your septic system before being used.

  • If you have had your septic tank drained within the last year or two, you will most likely not need to have it pumped out again.
  • If you notice that all of your drains are draining slowly, you most likely have a clog in one of the lines that drain away from your property.
  • Because the diameter of these pipes ranges from 4 to 8 inches, they are likely to be thinner in certain regions than others.
  • You may be experiencing some sewage backup into plumbing fixtures in your house or accumulating near your septic tank if your drains are working properly but you’re not sure what’s causing it.
  • It’s possible that the problem is in your septic tank’s entrance baffle, which you should be able to see if you have access to this area of the tank.

If there is a blockage in this baffle, you should be able to tell immediately. In certain cases, pushing the clog via the access port may be sufficient to clear it out. If you’re unclear of how to access any of this, you should seek the advice of a professional plumber.

Tree Roots are Infiltrating Your Pipes

Tree roots that are in the way of a septic tank’s operation can also be a source of problems. Whether sewage is beginning to back up into your drains, there are inexplicable cracks in your driveway and sidewalk, or you notice persistent puddles and damp spots in your grass even when it hasn’t rained, it is possible that roots have penetrated your plumbing system. Roots may develop fractures in your drain pipes, and if they continue to grow over time, these fissures can expand and cause significant damage.

The installation of modern, plastic pipes that are capable of withstanding root damage can help you avoid the problem of root penetration.

Root growth inhibitors are also recommended if you have trees near to where your pipes are located, since this will prevent them from growing.

You should chop down any trees whose roots are penetrating your pipes and remove the stumps in order to prevent roots from sprouting back after you’ve cleaned out your pipes if you are able to bear the thought of doing so.

Leaks in Sewage Tank or Lines

Many homeowners dream of having lush, green grass, but if your lawn is vibrantly green but the plants around it are dead, it might be an indication of a septic tank leak, according to the American Septic Tank Association. Experiencing unexplained green grass might also be an indication that your septic tank is pumping out an excessive amount of water, soaking your yard. Moreover, there may even be sewage accumulating in your yard in this situation. This is an issue that should be addressed by a plumbing specialist as soon as possible in order to minimize any potential health risks and costly damage to your property.

IncorrectSeptic Tank Installation

The proper installation of a septic system allows the system to operate smoothly. Know if the firm who built your septic system done it in an accurate and timely manner? Most likely, if you bought an older property, you have no idea who built the septic system in the first place. Furthermore, because you can’t look into your septic system, you have no idea what’s going on down there as well. Failure to bury the tank deeply enough, installing the incorrect-size tank, or utilizing the incorrect soil in the drainfield are all examples of installation problems that can result in septic tank failure.

Increased Water Use

Before it overflows, your septic tank can only contain a certain amount of water. Septic tanks can collapse if there is a high number of people who depend on them for their water. If you have a big family, expect a significant number of long-term guests, or often hold parties, you should get your tank examined to ensure that it is the proper size. If this is the case, you may need to consider upgrading to a larger tank. Your septic system is capable of withstanding a lot of abuse, and it should continue to function well for many years provided it is properly maintained.

If you see any indicators of septic tank difficulties, such as clogged pipes, root infiltration, or sewage leaks, act promptly and call The Original Plumber for a septic tank check to ensure that any problems are resolved as soon and efficiently as possible.

Clogged Drain vs. Septic Backup

Drains in your business or house are draining slowly and/or regularly clogging. If you have an onsite waste disposal system, such as a septic tank system, the problem must be properly recognized and addressed. A clogged drain or a sluggish drain may frequently be remedied by removing the plumbing backlog that has built up inside the structure. You can be wasting your time and money, though, if the issue is with your septic tank and you are trying to tackle the wrong problem. What are you going to do?

However, it is prudent to examine and locate the issue location first – as it is possible that the problem is not located within the structure.

We have a great deal of expertise with all types of drain vs septic field concerns, as well as economical septic tank repair.

Plumbing Drain Noises

Whether you believe it or not, plumbing drain sounds might assist you in locating the root of a problem. It’s possible that the “blub glub” sounds coming from a drain where water is flowing is indicative of a problem with:

  • Drain venting issue caused by a partial drain obstruction, which forces the water through a limited region, resulting in a hiss or blub sound. A gurgling sound can be produced by plumbing vents that are insufficient (or altogether absent). As a result of confined air or a partial vacuum, there is insufficient free flow. Drain venting may be the source of gurgling at the sink or shower drain only when a neighboring fixture is in operation, such as when a toilet is flushed. Noises coming from the plumbing drains that do not interfere with operation. Some pipe materials are more susceptible to noise transmission than others. Plastic drain piping has a distinct sound from cast iron drain plumbing. The answer is good sound insulation, but you need hire a professional plumber to locate the source of the sound or noises and install the appropriate type of insulation at the appropriate locations
  • “unusual solutions” amateur plumbing are not recommended. If an inexperienced handyman attempts to solve a plumbing problem using non-standard remedies such as running waste lines inside the building at strange angles, which battle against gravity and result in noise and pools of stagnant water that accelerate corrosion or leaks at joints, he may be held liable. A sewage gas odor may also be produced, which can be detected at the fixture itself.

If a single fixture in the building is sluggish or blocked, but the rest of the fixtures are functioning normally, the problem is most likely not with your septic tank. A clog in the waste or soil stack (drains from sinks or toilets) is the source of the problem, and here is the first place to look for solutions. If the drains in your whole home are slow or blocked, or if waste is backing up into the lowest-elevation plumbing fixtures, the septic tank or field should be suspected.

Septic System Issues

Even while you may think of your septic tank as a single component, it is actually a complex system that includes waste pipelines, absorption areas in the ground, and of course, the tank itself.

  • Absorption fields are a type of field that absorbs energy. What happens when it rains? Is your problem worse by rain? If this is the case, you may require the services of a professional inspector. Your septic tank’s absorption field should be approximately five feet below the level of the high water table, according to the manufacturer. If this field is placed incorrectly, it is possible that the field may become flooded and will be unable to handle the outflow from the tank. As a result, it is possible that pathogenic elements from the tank are polluting the groundwater in the surrounding area. This is clearly not a do-it-yourself project. Contact Benjamin Franklin Plumbing in the Bay Area and we’ll send out a septic tank system expert who is knowledgeable and well qualified to assess your problem and recommend a cost-effective solution
  • When an absorption field fails, there are only two options: either construct a completely new drain field or enhance the capacity of the present field by adding more branches to it. The sludge in the tank has the potential to develop a layer of biodegradable material beneath the pipes, preventing the water from seeping into the soil. In order to prevent this from happening, the standard for septic tank care requires that the tank be pumped out every three years. Although the septic tank has been drained, backups continue to occur. This might be an indication that the pipes leading from the fixtures to the septic tank are clogged with debris. Having these pipes professionally cleaned should be the first order of business. In order to find any blockages caused by sludge, fractures or cracks in the pipe, or roots, our plumbers can send a camera down the line. This approach may also be used to evaluate if the septic tank is operating properly. When you narrow the scope of the problem to the area between the building and the septic tank, you will discover standing water in the line that connects them. In addition to the causes listed above, the drain pipe may collapse as a result of movements in the soil, power snake damage, corrosion, or a combination of these factors. In many of these situations, the scum (on the top) and sludge (on the bottom) levels in the tank have risen past their maximum limits, and the septic tank must be drained out quickly. Despite the fact that the lines are clear and the septic tank has been pumped, there is still a backup into the structure. This is frequently caused by a problem with the drain field. Effluent sludge in the tank rises to the surface and pours out of the tank, blocking the drain field and causing the flow from the tank to get backed-up. This can occur when the field is incorrectly pitched or set out, resulting in the field becoming a magnet for rainwater and groundwater, as seen in the image below. Therefore, the wastewater is prevented from adequately draining into the field as it should, resulting in septic tank backup during a party or while visitors are coming or staying at the house. In most cases, this occurs when the septic system is unable to handle the additional multiple gallons of water created by an unexpected increase in the number of people using the facility. It is a problem with a large amount of wastewater that is made worse by the fact that the tank was not empty enough to accept the additional input. Having a large amount of wastewater in a short period of time might generate a flooding situation in the drain field, which can result in a backup of wastewater entering your home through the waste line.

Post Navigation

Leave a Comment

Your email address will not be published. Required fields are marked *