How Do I Install A Septic Tank Riser Over A Square Opening? (TOP 5 Tips)

  • In order to put septic tank risers onto your septic tank, you need an adapter ring. Polylok has one of the largest adapter rings on the market allowing you to cover up to a 25’’ square opening or a 27’’ round opening. This ring accepts both 20’’ and 24’’ risers and gives you great flexibility no matter what size your opening may be.

Do they make square risers for septic tanks?

The Polylok square riser adapter ring is designed to connect the Polylok septic tank risers or lids to an existing concrete tank with large square or round openings.

How many lids do septic tanks have?

A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

How does septic tank riser work?

A septic tank riser is a pipe made of either plastic, fiberglass, or concrete. It creates a vertical portal at the ground surface for easy access to the septic tank for inspection and pumping out. The lid is then either left exposed or with a very thin layer of soil and grass over it.

Can you pour concrete over septic tank?

Paving Over Your Septic Tank You should never pave over your septic tank. Although soil compaction is not a major issue for septic tanks, there are other dangers presented by placing an insecure septic tank underneath concrete and heavy vehicles. This is particularly the case for old, reused septic tanks.

Why does my septic tank have 2 lids?

Solid, watertight, buried tank made of concrete, plastic, fiberglass or metal. This tank has a way in (inlet), and a way out (outlet). So, most residential tanks should have (2) lids about 5′ away from each other. A septic tank holds all the liquid waste from your home (toilets, sinks, kitchen, bathtubs, floor drains).

How far apart are septic tank lids?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

Can you cover septic tank lids?

If you have a traditional septic system, the tank should be pumped every 3-5 years. That means that the septic lids should be accessible every 3-5 years. You can use almost any temporary, movable objects to cover your lids, like: Mulch (but not landscaping)

How many septic tank risers do I need?

A single riser is required for accessing the pump chamber for this type of system. If you don’t have two additional risers, you should locate your septic tank and install risers for both the inlet and outlet openings, as described above.

How do you measure a septic tank lid?

You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath.

How to Install Risers and Lids on Concrete Septic Tanks w/ Square Hole

Posted on the web by Installing risers and lids will make it much easier to get access to the septic tank for inspection, repairs, and pumping. There is an up-front expense, but that cost can be compensated over time by the cost of locating and digging every time you require access to the tank, which can add up over time. Determine the height of the riser. Tank risers are normally installed around 3 inches above the ground’s surface temperature. Having the lid at ground level will make it simpler to locate; however, some people prefer to have the lid a few of inches below ground level so that it is easier to mow over and less noticeable while in use.

The height that is chosen is entirely a matter of personal taste.

Begin by digging all the way down to the tank, cleaning and preparing the area surrounding the existing hole to the best of your ability.

Attach the tank adapter ring to the tank using stainless steel concrete anchors after applying the butyl sealant tape to the bottom of the ring.

Install half of the epoxy on the adapter ring and lower the riser so that it rests on top of the epoxy.

The epoxy and riser are seen in the illustration below.

Use the provided fasteners to attach the lid, as illustrated below.

Installing Access Risers

In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below. Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.

A few safety tips before you get started:

  • Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website
  • Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.

Gather all the MaterialsTools You will Need

It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.

Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.

Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.

See below for Step 4 on attaching risers to the tank entrance. For the purpose of installing a riser system on your septic tank, you will require the following components:

  1. Tank Adapter Ring (TAR)
  2. Riser Adapter Ring Kit
  3. Butyl Rope
  4. Risers
  5. Domed Lid OR Flat Lid
  6. Stainless Steel Screws

The following materials will be required for digging up your septic tank(s):

  1. Digging up your septic tank(s) will require the following materials.

Materials required for the excavation of your septic tank(s) include:

  1. Circular saws, saber/jig saws, and hand saws
  2. Raspor file
  3. Marking pen
  4. Tape measure
  5. Drill with a 1/4″ bit

Materials required to seal the risers to the tank include:

  1. High-strength concrete patch mix
  2. A small bucket
  3. A mixing stick
  4. And gloves

Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.

Step 1: LocateYour Septic Tank(s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.

Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.

The presence of underground electricity or other utility lines and cables might put your septic tank in danger.

Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.

Step 2: Uncover Your Septic Tank (s)

Once you’ve discovered your septic tank, you may start digging about. The tank is typically 6 feet wide by 8 feet long, with the width being the largest size. Remove all of the pebbles and debris from around the tank’s lid openings and dig out the whole top of the tank. You will want to clean out any dirt that has accumulated on the surface of your septic tank. This will assist you in ensuring that you generate a high-quality seal. You should have two openings: one over the inlet (which comes from the home) and another over the outlet (which comes from the yard) (into the drainfield or pump chamber).

  1. You’ll need a riser for each of the doors you open.
  2. Typically, the inlet side is the one that is nearest to the home.
  3. When cleaning the tank, it is beneficial to remove the complete top of the tank.
  4. Risers must be modified in order to be correctly installed, and all manholes (holes 24 inches or bigger in diameter or square in shape) must also be updated, as well as the tankinlet and outlet baffle covers (if separate from the manholes).
  5. If you discover one – and only one – riser already installed, it is most likely for the pump chamber, which only requires a single riser to provide access to the pump to function properly.
  6. Remove the concrete lids so that they may be disposed when the project is completed.
  7. Consult your’As-built’Recorddrawing to establish whether you have a distribution box (D-box), which you will also need to unearth and place a riser on if you have a typical gravity system.
  8. Once the lids have been removed, proceed with caution around the tank.
  9. Inform someone of your whereabouts in case you are involved in an accident.

You should be aware that exposure to sewage can result in serious sickness, so make sure you wear gloves and thoroughly wash your hands afterward with soap and water. It is also recommended that you wear eye protection in the event that debris falls into a tank and splashes back at you.

Step 3: Fit Risers to Component Openings

In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:

  • Large risers will either rest on top of the septic tank or fit down into the tank opening by 1-3 inches, depending on the diameter of the septic tank manholes. When establishing the height of the riser, keep this in mind as you measure. The additional length may be easily removed
  • However, it is quite difficult to add a few inches. Obtain the following measurement of the manhole cover’s circumference:

Large risers will either rest on top of the septic tank or will fit down into the tank opening by 1-3 inches, depending on the diameter of the septic tank manholes. When selecting the height of the riser, keep this in mind. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the overall length. Take the following measurements of the manhole cover:

See also:  How Much Fill Dirt Over A Septic Tank? (Correct answer)

Step 4: Attach Risers toSeptic Tank (s)

Large risers will either rest on top of the septic tank or will fit into the tank entrance by 1-3 inches, depending on the diameter of the septic tank manholes. Keep this in mind while selecting the height of the riser. It is EASY to clip away the excess – it is HARD to add a few inches more! Measure the diameter of the manhole cover as follows:

How To Instal Risers On A Septic Tank

A septic tank riser system will be installed today, and we will demonstrate how to do it. If you have a concrete septic tank that does not have risers built, this instruction is for you. It is currently mandatory in many areas to have risers and lids installed on your septic tank. When it comes time to have your septic system pumped out, installing a riser system can also save you money. Please follow the instructions in the following section and you will have no difficulties.

Step 1 – Gather The Parts You Need

A riser system for a septic tank will be demonstrated in this article. If you have a concrete septic tank that does not have risers built, this article is for you! It is currently compulsory by many states to have risers and lids installed on your septic tank. When it comes time to have your septic system pumped out, installing a riser system might save you money as well. Following the instructions in the following section should alleviate any difficulties.

Step 2 – Clean The Top Of Your Septic Tank

You will want to clean out any dirt that has accumulated on the surface of your septic tank. In doing so, you will increase the likelihood of successfully creating a good seal. A concrete ring is seen on the left side of the image. Using this as an example, we will illustrate how to install a riser system. In order to offer a visual picture of a hole in a concrete septic tank, the following image was created. The diameter of this one is 16 inches. It is possible that your hole is bigger or smaller.

Remember to measure the hole diagonally before purchasing the appropriate Tuf-Tite Tank Adapter Ring.

Step 3 – Apply Butyl Rope To Tank Adapter Ring

To secure your Tuf-Tite Tank Adapter ring to the bottom of your tank, tie a butyl rope ring around it.

This will aid in the creation of a water-tight seal. Make sure the butyl stretches all the way around the Adapter Ring before you tighten it.

Step 4 – Put Adapter Ring Around Hole And Screw It Down

Firmly push the Tuf-Tite Tank Adapter Ring onto the septic tank’s adapter ring to secure it. To begin drilling the holes, use the drill bit that included with the package. The Adapter Ring will have divots in the areas where the holes will be located. Once you have pre-drilled the holes, you may use the blue concrete tapping screws that are provided to secure the ring to the top of your installation system.

Step 5 – Add Butyl Rope To The Bottom Of Each Riser

The bottom of each riser will have a recessed ring in the center. In this ring, insert a strip of butyl rope and tighten it. This will ensure that the risers are watertight.

Step 6 – Put Risers and Lids On The Adapter Ring

Now it’s time to attach your risers to your Adapter Ring. Their installation will be accomplished by screwing them into place using stainless steel screws. In order to raise it to the proper height, you can use as many risers as necessary. That’s all there is to it. You have completed the installation of a riser system on your septic tank, which should pass inspection anyplace in the United States of America.

Polylok Square Septic Tank To Riser Adapter Ring – 3009-AR

  • Tank may be fitted with Polylok Risers and Lids that are either 20″ or 24″ in diameter
  • It has a maximum opening of 25″ square or 27″ round
  • It has a large, flat surface area that makes tank mounting simple.

The adapter ring is the first component that you’ll need to put together in order to assemble a full riser system. The adapter ring attaches directly to the septic tank, allowing the risers to stack, lock, and mount to it without the need for any additional hardware. Having this component is critical since the risers are not flat on the bottom because they are meant to be stackable, and it is not feasible to install them straight to the septic tank without this piece. The adapter ring provides the flat surface you need to mount to the tank while also being able to accommodate the stackable risers that are included with the tank.

Our square tank adapter ring can accommodate big square apertures up to 25 inches in diameter and large round openings up to 27 inches in diameter.

They are intended to be used with openings that are 24″ or less in diameter.

Concrete anchors, a masonry bit for installing the anchors, and butyl sealer are all included in this set.

ADAPTER RING INSTALLATION

1.Clean the tank surface area over the aperture where the riser adapter ring will be installed; a minimum of 36″ of space should be left for the riser adapter ring. Check the plug size to ensure that the riser is not obstructed. 2.Place the riser adapter ring on the tank surface and mark the anchor locations using the anchor holes in the adapter ring. The 24″ position will necessitate removal of the 20″ ring, thus choose the appropriate size riser for your needs. To remove the riser adapter ring, turn it over and cut along the score line to release it.

Anchors might be any of the anchors that are usually accessible.

If you are using butyl mastic or silicone sealants, insert the riser-sealing strip on the bottom of the riser adapter ring in the proper location for the riser size that you are using.

Additional risers should be inserted into the riser adapter ring, with the screw holes aligned to ensure that the portions of the risers are securely fastened together.

8. Attach the riser cover to the top of the riser using the screws that were provided. 9.The installation is complete, but if FROST is present in your region, you may wish to remove the riser rings from any further risers before final backfilling it.

Polylok Septic Tank Risers

Nowadays, there are several different types and designs of septic riser kits and packages available on the market. Building a septic riser kit with Polylok goods will ensure that you are getting the most value for your money. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

Once the hole has been backfilled, the structural ribs in the Polylok septic tank risers are inserted inside around each riser piece, providing them with tremendous strength and allowing them to maintain their shape under the pressure of the earth being pressed on them. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

LOW PROFILE RISER LIDS WITH HANDLES

The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE TANK ADAPTER RING

An adapter ring is required in order to properly install septic tank risers on your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

STAINLESS STEEL SCREWS INCLUDED

At Septic Solutions, we strive to make the buying and installation process as simple as possible for our customers. All of our Polylok Septic Tank Risers and Lids are delivered with all of the stainless steel screws required for installation in one package.

Septic Tank Risers & Lids

SAME DAY SHIPPING ON ALL SEPTIC TANK RISERS, LIDS, AND ADAPTERS WITH FAST AND FREE SHIPPING.

Polylok SQUARE Riser Adapter Ring

An existing concrete tank with big square or round apertures may be connected to a Polylok square riser adapter ring, which is designed to attach Polylok septic tank risers or lids to the existing concrete tank.

The adapter ring attaches directly to the tank and takes the risers and lids as accessories. It is made of stainless steel. Use ourInstallation Kitbelow to make the process as simple as possible. Specifications of the product

  • Accepts Polylok Risers and Lids in either 20″ or 24″ widths
  • Covers a maximum of 25″ square or 27″ diameter openings
  • Tank mounting is made simple by the large, flat surface area.
Availability: IN STOCK
Technical SpecificationsWatch MoreAbout Polylok Risers

If you want technical assistance, please contact our support department at 1-877-925-5132.

Polylok ROUND Riser Adapter Ring

An existing concrete tank with a round entrance, existing concrete round risers, or existing plastic risers may all be connected to the Polylok septic tank risers or lids using the Polylok roundriser adapter ring. The adapter ring attaches directly to the tank or riser and takes the Polylok risers and lids as accessories. The adapter ring is available in two sizes. Use ourInstallation Kitbelow to make the process as simple as possible. Specifications of the product

  • Available in two sizes: 20″ and 24″ in diameter. Polylok may be used to adapt round openings or existing Risers to the material. Tank mounting is made simple by the large, flat surface area. Availability: AVAILABLE IN STOCK
Adapts 20′ or 24′ Round Openings or Risers to Polylok Risers and LidsWatch MoreAbout Polylok Risers

Put your trust in the professionals with more than 20 years of expertise in the wastewater business.

Polylok Septic Tank Riser Lids

The Polylok septic tank riser lids are designed to suit only Polylok septic tank risers or adapter rings, and they are not compatible with any other brands. The lid snaps into place and is secured in place with stainless steel screws that are provided. Specifications of the product

  • Easy removal is made possible by the flip up handles
  • A factory installed gasket provides a watertight seal
  • Stainless steel screws are included
  • Only Polylok Risers and Adapter Rings are compatible with this product. Availability: AVAILABLE IN STOCK
Replaces Models PL-20RC, PL-24RCTechnical Specifications Watch MoreAbout Polylok Risers This lid can handleweight up to alawn mower or small garden tractor
See also:  What Size Opening Needed For Pumping Septic Tank? (Correct answer)

To make an order, you may purchase online at any time or phone us toll free at 1-877-925-5132.

Polylok Heavy DutyRiser Lids

For orders, you can place them online at any time or by phone at 1-877-925-5132.

  • Ratings for heavy loads up to 3500 pounds have been tested. Factory-installed gasket provides a watertight seal
  • Stainless steel screws are included for assembly. Polylok Risers or an Adapter Ring are compatible with this product. Covers for 24″ corrugated or dual wall pipe are available. Availability: AVAILABLE IN STOCK
20′ Heavy Duty Lid ( 3017-C20) Technical Specifications24′ Heavy Duty Lid ( 3008-WEST) Technical Specifications

Do you require assistance? Please contact us toll free at 1-877-925-5132 for professional assistance.

Polylok 6′ Tall Septic Tank Riser

Polylok septic tank risers are among the most durable products available on the market today. They may be stacked, which provides a great deal of versatility when it comes to raising the grade of the entryway. Each riser is secured in place with the stainless steel screws that are supplied with the purchase. Specifications of the product

  • Structures with heavy-duty structural reinforcements for increased strength
  • Factory-installed gasket provides a watertight seal
  • Stainless steel screws are included for assembly. Polylok Risers and Adapter Rings are the only ones that will fit. Availability: IN STOCK
Watch MoreAbout Polylok Risers All Polylok Risers are stackable giving greatflexiblity when bringing your access to grade!Stainless Steel screws included for attachment

We provide the greatest collection of septic goods on the internet, with over 850 different options.

Polylok 12′ Tall Septic Tank Riser

Polylok septic tank risers are among the most durable products available on the market today. They may be stacked, which provides a great deal of versatility when it comes to raising the grade of the entryway. Each riser is secured in place with the stainless steel screws that are supplied with the purchase. Specifications of the product

  • Construction with heavy-duty structural reinforcements for added strength
  • Factory-installed gasket for a watertight seal
  • Stainless steel screws are included
  • **The safety screen (3008-SS) will not function with the 24×12 Riser** Polylok Risers and Adapter Rings are the only ones that will fit. Availability: IN STOCK
Watch MoreAbout Polylok Risers All Polylok Risers are stackable giving greatflexiblity when bringing your access to grade!Stainless Steel screws included for attachment

Put your trust in the professionals with more than 20 years of expertise in the wastewater business.

Polylok 2′ TALL Grade Riser

To finish adjusting your access point to the final slope, use the Polylok 2″ Tall Grade Risers to complete the job. This object can be placed at any point along the riser stacking hierarchy. When in use, the grade riser locks into place and is secured with stainless steel screws that are provided. THIS ITEM WILL NOT BE COMPATIBLE WITH THE SAFETY SCREEN! Specifications of the product

  • Available in two diameters: 20″ and 24″. Factory-installed gasket provides a watertight seal
  • Stainless steel screws are included for assembly. Only works with Polylok Risers. Availability: AVAILABLE IN STOCK
Watch MoreAbout Polylok Risers All Polylok Risers are stackable giving greatflexiblity when bringing your access to grade!Stainless Steel screws included for attachment

To make an order, you may purchase online at any time or phone us toll free at 1-877-925-5132.

Polylok Safety Screen

The Polylok safety screen serves as a backup layer of protection in the event that the riser cover is broken or removed accidentally. The screen is compatible with both the 6″ and 12″ tall risers. Specifications of the product

  • With a built-in handle for simple removal
  • Tested at a density of 250 pounds per square foot Screws made of stainless steel are included. It is compatible with both the Poylok 6″ and 12″ Risers. Availability: AVAILABLE IN STOCK
Watch MoreAbout Polylok Risers PLEASE NOTE: SAFETY SCREENDOES NOT FIT 24′ RISER PAN

Do you require assistance? Please contact us toll free at 1-877-925-5132 for professional assistance.

Adapter Ring Installation KitHighly Recommened

It includes everything you need to quickly and easily install and attach the Polylok Adapter ring to your septic tank, including all of the necessary hardware. Included in the Anchor Kit is:

  • The following items are available: (1) 20-foot roll of Butyl Sealant
  • (8) Concrete Wedge Anchors
  • And (1) Masonry Drill Bit

Put your trust in the professionals with more than 20 years of expertise in the wastewater business.

Butyl Sealant Rope

The butyl sealant rope is used to create a watertight seal between the adapter ring and the septic tank. The butyl seal rope is 5/16′ round and comes on a 20 foot roll.Availability: IN STOCK

Take advantage of professionals with more than 20 years of expertise in the wastewater sector.

Handle For PreCast Concrete Lid

Extremely strong, non-corrosive HDPE ribbed handle forprecastconcrete septic tank and distribution box lids. Also acceptssnap-onwarning placards.

Steps that you should follow to install risers on a septic tank

Many American households are projected to consume more than 300 gallons of water each day in their houses, but do you know what happens to the wastewater once it leaves your home? Many people assume that whatever they flush down the toilet will just disappear; but, if you have a septic system, everything will wind up in your septic tank as a result of the flushing.

  • Where does this waste water originate from? Toilets, showers, sinks, dishwashers, and washing machines are all potential sources.

Toilets, showers, sinks, dishwashers, and washing machines are some of the sources of this waste water.

1.Get all the necessary parts together

In order to prepare to build a riser system on your septic tank, you will need to purchase a few goods. These items include a Tuf-Tite tank adapter ring (TAR), a kit for riser adapter rings, butyl rope, Tuf-Tite risers, a Tuf-Tite domed lid or a Tuf-Tite flat lid, and stainless steel screws. The adapter, lid, and risers should all be slightly bigger in diameter than the hole in your septic tank.

2.Make sure the top of the septic tank is clean

One of the most important steps in ensuring that you do a good job of installing risers on your septic tank is to ensure that you create a good seal; this means that you must ensure that the top of your septic tank is perfectly clean so that dirt does not ruin the seal during the installation process.

3.Applying the butyl rope to your tank adapter ring

One of the most essential things to do to ensure that you do a good job of putting risers on your septic tank is to ensure that you create a good seal; this means that you must ensure that the top of your septic tank is totally clean so that debris does not destroy the seal during the installation.

4.Putting the adapter ring in place properly

The next stage in the process of placing risers on your septic tank is to ensure that the Tuf-Tite tankadapter ring is correctly secured in place. You’ll want to press the adapter ring onto the septic tank with a little force to ensure that it stays in place. As part of the package that you ordered, you should have a drill bit that will enable you to begin drilling holes in the areas where you see divots on the adapter ring. As soon as the holes are drilled, you may use the tapping screws that included with the package to fasten the adapter ring to the top of your system in the right manner.

5.Apply butyl rope to the risers

In order to make each riser watertight, butyl rope should be wrapped around the recessed rings on the bottom of each one.

6.Place the risers on the adapter ring

The next step is to ensure that the risers are correctly secured to the adapter ring. That’s all there is to it!

What You Should Know About Septic Tank Risers

Septic tank risers are an important part of any septic system, and they should be installed in every property. This article will provide you an overview of septic tank risers and how they may help your septic system. What Is the Function of a Septic Tank Riser? A septic tank riser is a conduit that connects your home’s surface drainage system to your septic tank beneath the ground level. An access port or the pump-out ports on the septic tank are where the riser connects to the tank. Septic tank risers are equipped with lids that can be quickly removed to allow you to check or pump your septic tank without having to dig up your yard.

  1. These structures are often made of materials that disintegrate slowly over time, such as plastic or concrete.
  2. What Are the Advantages of Using Risers?
  3. Normally, this entails digging up your yard before the pump is installed and reburying the tank once it has been installed.
  4. The use of a septic tank riser can help to minimize the amount of time spent pumping your septic tank.
  5. The fact that the riser is visible above the surface of your yard makes it an ideal signal for locating your septic tank the first time you need to discover one in your yard.
  6. For those who want to stay in their house for several years, septic tank risers are not only handy, but they are also cost-effective.
  7. Concrete risers are more durable, but they are also more expensive, and the price will be determined by the quote you receive from the contractor who will be installing them.

Because labor expenses account for a large amount of the fees that contractors charge for septic system inspection and pumping, installing a riser may possibly reduce the future cost of septic service by as much as 50 percent.

Each and every property can profit from the installation of a septic tank riser, but this does not imply that you should do so immediately.

This allows for the installation of the pump and riser to be completed in a single step.

Because a riser should be considered a long-term investment, you should be certain that your tank is in good functioning shape before installing one.

A septic tank riser is a straightforward concept that may save you a significant amount of money and pain when it comes to septic system maintenance and repair.

We look forward to hearing from you and addressing any concerns you may have concerning your septic system requirements. Contact us now. Please let us know how we may be of assistance to you and your septic system right now!

Match The Correct Riser And Lid To The Tank To Ensure Safety And…

Receive articles, stories, and videos about septic tanks delivered directly to your email! Now is the time to sign up. Septic Tanks and More Receive Notifications We receive a constant stream of queries concerning how to install risers and, by extension, how to install the lids on those risers. One of the most prevalent themes we hear when it comes to system installation is that systems must be built with monitoring and maintenance in mind. This implies that all components must be fitted in a way that allows them to be readily reached by experts and that allows them to be repaired or replaced when necessary.

As a result, offering cost-effective service is dependent on providing quick access.

This makes the task of the service provider or inspector while examining the state of the tank, as well as the duty of the pumping contractor when the tank is full, a whole lot easier to do.

CHOOSE THE RIGHT MATERIAL

There are several different types of rims and lids available, including concrete, polyethylene, polypropylene, polyvinyl chloride, and fiberglass. No matter what material is used, the riser and the connection to the tank or additional risers must be waterproof and resistant to root intrusion. If roots are able to get through, the structure is not waterproof! Risers should also be structurally stable, so that they do not lose their form after backfilling with concrete. In the case of concrete tanks, a riser is frequently cast into the tank during the manufacturing process.

  1. If you live in a cold area, you will benefit from using cast-in-place risers since they are less susceptible to frost heave, which causes risers linked with joints to split over the winter and impairs watertightness.
  2. The majority of what we’ve seen so far includes casting an adapter ring into the tank hole, which is advantageous because having risers cast in place might interfere with setting the tank and being in the way when the system is fitted.
  3. It is critical to follow the manufacturer’s directions while applying sealants to guarantee that the building is waterproof.
  4. Watertightness is achieved by the use of mastic and other sealants.
  5. This is the standard layout for tanks that are newly constructed.

As an installation or service provider, on the other hand, you are frequently confronted with older concrete tanks that do not have a built-in riser. As a result, an upgrade is required to bring a riser to the surface for future service convenience.

RETROFITS

Making these connections completely waterproof is a difficult task. We frequently encounter a riser that is somewhat bigger or of a different shape than the current aperture (round versus square), mostly because it is the most readily available option on the market. It is then placed over the top of the tank lid in an attempt to mortar them into place, before being removed. They are readily loosened, and when the tank is opened, it is discovered that water and soil have been introduced into the tank through this connector.

  • The good news is that new items to assist with this issue are being accessible all of the time, which is encouraging.
  • Most polyethylene and fiberglass tanks will have risers incorporated into them at the time of production, unless otherwise specified.
  • To keep children and animals out, lids must be built of sturdy materials with connections that are both water- and air-tight, and they must be kept closed when not in use.
  • Homeowners may also object to lids that are visible on the surface of the water.
  • Service providers can utilize a metal detector to find the tank entry point in a short amount of time.
See also:  When Can U Install Septic Tank? (Question)

MORE SAFETY TIPS

We believe it is preferable to have the lids raised a couple of inches above the surface of the water to make it easier for the service provider to reach the water. It is critical, however, that the lid is secured with nonstandard bolts or screws to ensure that minors, in particular, are unable to open it. Every year, we receive a number of instances of youngsters falling into septic tanks and being gravely hurt or killed because the lid has not been properly affixed to the riser, as is often the case.

These devices are available for purchase separately.

Purchasing this insurance coverage and upgrading their system may prove to be a wise investment.

In most cases, this results in riser deformation and a lack of watertightness, as well as the creation of a dangerous access problem.

It is expected that following these principles would make tank entry and servicing easier, resulting in better maintenance for septic systems and a longer service life for them.

Septic Riser & Lid Repair Statesville

Sewage Tank Risers and Lids or Lids are intended to be used in conjunction with existing concrete, fiberglass, or metal septic tank covers. Septic Risers are meant to raise the level of a septic tank’s below-grade opening to the same level as or higher than the surrounding ground. Risers are frequently absent from typical septic tanks, particularly in earlier types, and are thus difficult to find. The diameter of risers typically ranges from 8 to 24 inches. Septic tank riser installation services are provided by Lentz Wastewater Inc.

The aperture of the riser is protected by a tight-fitting lid.

Do I Need a Septic Tank Riser?

A septic tank riser system is an extremely beneficial addition to your septic system and is highly suggested by experts. This device will make the process of maintaining and monitoring your septic system more easier, more convenient, and less expensive. Septic tank risers that have been authorized by the state of North Carolina must be put on any new or updated septic system in the state. Your septic system is one of the most expensive mechanical elements on your property. It is also one of the most complicated.

If you don’t have septic tank risers, your system will be “out of sight and out of mind” for a long time.

Advantages of Septic Tank Risers

  • Rising and covering septic tanks in the modern day are significantly more aesthetically pleasing and mix in with their environment
  • The lightweight septic cover makes it simple to get access to the septic tank. The contemporary covers are lightweight, weighing less than 10 pounds, which makes maintaining your tank considerably simpler. The old-fashioned concrete septic tank riser rings are quite heavy, weighing hundreds of pounds. The concrete coverings are similarly heavy, weighing between 60 and 80 pounds. Many individuals are deterred from lifting the cover and doing an inspection because of the weight of the object. Septic tank riser rings made of modern polyethylene are often less than 30 pounds in weight. Septic tank risers also have the advantage of making it considerably easier to prevent surface water from entering the tank. In the olden days, concrete riser rings were not equipped with a gasket. As a result, surface water may readily flow between the connection between the tank and the riser ring, as well as between the lid and the riser ring, when the tank is filled with water. Nowadays, a watertight seal is installed between the septic tank and the base flange of the riser. The riser rings and covers are also equipped with a long-lasting closed-cell foam gasket to keep the junction between them from becoming leaky. To keep little children from curiously messing with the cover and putting themselves in danger of falling into the septic tank, modern riser covers are fastened with threaded screws.

Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover. Our septic tank risers and covers are constructed of high-quality, heavy-duty polyethylene plastic, which allows them to be both extremely robust and durable while still being lightweight and simple to handle and transport.

Damaged Septic Tank Cover?

In the event that you drive over your septic tank, which is not suggested at all, the cover or lid may be damaged. Lentz Wastewater fixed septic riser covers that were broken, damaged, or mi ssing.

Septic Tanks – Traverse City, MI – Belanger Septic & Security Sanitation

Risers are used on septic tanks to raise the lid of the tank to a safe level. They assist to reduce the expense of pumping a septic tank by eliminating the need to identify and dig up lids on tanks, as well as safeguarding your irrigation and landscaping. Risers are simple to install and may be done by the homeowner, or we can do it for you. We are able to accept a wide range of lid designs. The majority of septic tank lids are circular, while some may be square depending on the manufacturer of your container.

We also provide several types of markers, such as stakes, imitation rocks, patio stones, and other similar items, to indicate the position of a septic tank. Once a riser is buried, it is no longer accessible and might be difficult to recover.

Find the Right Size for Your Septic Tank

There are several various riser sizes available, ranging from six inches in diameter all the way up to thirty-six inches in diameter. In no case should a six-inch riser be installed on the first septic tank or the inlet end of a twin compartment septic tank. Solid sewage cannot be removed through a six-inch hole because of the size of the hole. When our professionals manipulate and break up the sewage, they do it with a paddle. Since there is no way to maneuver your hose around the tank to pump the corners, we end up simply pumping the water and leaving behind a significant amount of sediments that will end up remaining in the septic tank if we pump via a six-inch hole.

If your septic tank was originally placed with six-inch risers, it is recommended that you remove them and have the larger risers installed at your next pumping service appointment.

How to Find the Lid on a Septic System

All septic tanks eventually fill with sediments and must be pumped out on a regular basis in order to remain in excellent functioning order. If the tank’s lid is not on a riser at ground level and you are not the home’s original owner, you may be unable to determine where the lid is located. A typical septic tank is 4 inches to 4 feet underground, with all of its components, including the cover, buried between 4 inches and 4 feet underneath. This is true regardless of whether the septic tank is equipped with special risers that keep the lid flush with the surface of the ground.

Consult A Map

First, choose with the most straightforward choice. The installation of septic tanks at all locations is recorded in most counties’ permission records, which are kept on file for future reference. Typically, this will include a schematic indicating the placement of the tank on the land, as well as certain dimensions that will allow you to measure to the precise site of the tank. If your tank was placed before your county made it a requirement to record the location of such tanks, you may find yourself with nothing to show for your efforts.

Search For A Sign

Septic tanks are placed in such a way that they are as unnoticeable as possible on the land. After the grass has grown back after installation and some time has passed, it is possible that just a few visual indications will remain. Pay particular attention to the contours of your yard for any inexplicable high or low points that might suggest the presence of an underground storage tank.

Follow The Pipe

Installation of the septic tank takes place along the sewage line that runs from the house into the front yard. Locate the 4-inch sewage pipe at the point where it exits the home in the basement or crawl space, if it is there. Locate the same spot outside and make a note of it. Insert a thin metal probe into the earth, identify the 4-inch sewage line, and follow it across the yard, probing every 2 feet, until you reach the end of the property.

Septic tanks are required to be at least 5 feet apart from the home in all states except Alaska. The majority of them are between 10 and 25 feet distant. Whenever the probe makes contact with flat concrete, fiberglass, or polyethylene it indicates that the tank has been located.

Locate The Lid

The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Investigate the tank’s circumference to determine its boundaries and outline the rectangle’s boundary using a pencil. A septic tank that was built before 1975 will have a single concrete lid that is 24 inches in diameter in the center of the rectangle. If the tank was built after 1975, it will have two covers made of fiberglass or polyethylene, centered at the ends of the rectangle and centered at the ends of the rectangle.

Call A Professional

Opening a septic tank is a job best left to the pros once the lid has been discovered. Concrete septic tank lids are extremely heavy, and many require the use of lifting tools to remove them completely. An open tank has the potential to release toxic gases. Anyone going around on the property who comes into contact with an exposed septic tank might be in risk. Because of the noxious vapors present in an open tank, falling into one can be lethal.

Mark The Spot

Make a note on the ground near where the tank was pumped by a professional and the lid was buried to serve as a reference in the future. In order to keep track of where you are, you should choose a hefty circular patio tile that is embedded in the ground. Additionally, draw your own map of the area and store it with your other important papers.

Leave a Comment

Your email address will not be published. Required fields are marked *