How Do I Get A Older Locking Septic Tank? (Best solution)

There are two ways to install a septic tank riser on your older septic system. Call a Septic Tank Professional: This is obvious but if you aren’t handy, like me. Then what you want to do is contact a local septic tank expert and let them know that you have an older septic tank and would like septic tank risers installed.

When did septic tank regulations change?

According to new regulations passed in 2015, if your septic tank discharges to surface water such as a ditch, stream, canal or river, you will have to upgrade your system to a sewage treatment plant or install a soakaway system by 1 January 2020.

How do I find a buried septic tank lid?

You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath.

How do you replace a concrete septic tank lid?

Push down on the pry bar to lift up one end of the concrete septic tank lid. Ask your helper to pull the lid handle and slide the lid to the side. If you have a large rectangular lid, repeat the prying-up process for the opposite end of the lid. Lift the lid away from the septic tank with assistance from your helpers.

Do all septic tanks have two lids?

A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

How do you tell if your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

Your Drains Are Taking Forever.
Standing Water Over Your Septic Tank.

Bad Smells Coming From Your Yard.
You Hear Gurgling Water.
You Have A Sewage Backup.

How often should you empty your septic tank?

What are the 2020 septic tank regulations?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

Can you sell a house with an old septic tank?

If you’re selling a property with a septic tank, then you must be transparent with buyers about the fact the property uses a one and provide a detailed specification of the system. In fact, You are required by law to inform a buyer in writing about the presence of a septic tank.

Do I need a certificate for my septic tank?

The General Binding Rules were designed to simplify the regulation of small sewage discharges. Septic tanks and small sewage treatment plants no longer need to be registered and there is no legal requirement to keep records of maintenance (although this is advisable).

Will metal detector find septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How far down is septic tank lid?

Often, septic tank lids are at ground level. In most cases, they have buried anywhere from four inches to four feet underground.

Do all septic tanks have filters?

First, not all septic tanks have a filter, especially the older septic tanks. Now many government agencies require or recommend a filter when a septic tank is installed. Cleaning a septic tank filter is different than pumping out a septic tank and cleaning it.

Do septic tanks have concrete lids?

Septic systems are an inexpensive and frequently viable option for sewer systems. The most common tanks, starting in the 1940s, are concrete, with 3 – 500# lids for a 1000 gallon tank or 4 – 500# lids for a 1500 gallon tank.

Can you replace the top of a septic tank?

If it is not rusted, you can replace the rusted top with a heavy-duty plastic or concrete lid. Concrete septic tank covers are heavy but strong and durable. Plastic covers offer faster access to the septic tank and are much easier to install.

How often does a 1000 gallon septic tank need to be pumped?

For example, a 1,000 gallon septic tank, which is used by two people, should be pumped every 5.9 years. If there are eight people using a 1,000-gallon septic tank, it should be pumped every year.

Importance of Securing Septic Tank Lids

The tragic death of a young Florida child has served as a stark reminder to many homeowners about the need of properly fastening septic tank lids and covers. The youngster went missing while attending a family birthday celebration at a park in Jacksonville, and his body was discovered in a septic tank later that evening, according to police. The death of the youngster sparked an inquiry into septic tank safety by television reporters, as well as a vow from the mayor of Jacksonville to standardize all of the tank lids in municipal parks.

Tanks can be guarded using one of the following methods:

A key
A lock
A lid that weighs at least 58 pounds

And A lid that can only be opened with specific tools

They went to parks and boat ramps and discovered irregularities with the tank lids and their fasteners, which they reported to the network.

Plastic, fiberglass, and metal tank covers were among the several materials used to construct the covers

Some were made of plastic, while others were made of metal. The fasteners on the tank lids differed as well
Some were padlocked shut, while others were bolted closed. In one park, the bolts that were intended to secure the lid had rusted, making it easy to open
In another, the bolts that were supposed to secure the lid had corroded, making it easy to open

And in a third, the bolts that were supposed to secure the lid had corroded, making it easy to open
More significant security measures, such as lids with padlocks, were in place in several parks, and in a few instances, access to the apertures was restricted to structures that were not available to the general public.

To assure the safety of all parks by securely fastening septic tank lids, it is necessary for the city to standardize the lids and fasteners used in all parks across it.

SAFETY AT HOME

The danger extends beyond public land and encompasses any private residences that have a septic system in their backyards as well. There are many of properties in Southwest Florida that have the same safety concerns as mine. Please contact us if you have a septic system and are unsure whether or not you are at danger of contamination. As part of our routine maintenance service, we inspect your septic system to ensure that all components, including the lids, are securely connected.

SECURING SEPTIC TANK LIDS

Have a professional examine your tank and evaluate the condition of the lid and fastening mechanism.

Check to see that the lid is secure and in good condition. If it is secured with a fastener, make certain that the riser is in excellent condition so that the fastening is securely set in place. Make certain that all screws and fasteners are securely fastened in place.

It is preferable to use stainless steel fasteners since they are more resistant to corrosion caused by corrosive gases from the tank and salty coastal air.

PEACE OF MIND

In the event that a tank is ever left open or exposed, you can add an additional safety element to provide further protection. It is possible to retrofit a safety device into any septic tank for a reasonable price. Septic manufacturers provide equipment that can help prevent someone from falling into a septic tank, such as screens that fit inside a riser or a locking mechanism that can only be opened with a key, among other things. It just takes a split second for an accident to occur, therefore never leave the lid open or unlocked, even for a single minute.

Aging Septic System Components Can Be Hazardous

You should be aware that the components of a septic system, whether it is still in operation but has been neglected or whether it is an old, abandoned system, can constitute a threat to health and safety, especially as they become less structurally sound. Learn about several septic components that might become dangerous as they age, as well as the reasons for this. 1. The lid of an old septic tank Some tanks, particularly older ones, may have concrete lids rather than risers with locking plastic covers, which are more common nowadays.

In addition to the potential of breaking free, the concrete may succumb to the effects of the gases contained within the tank.
This acid can cause concrete to crumble over time.
If you have a concrete lid, it should be replaced.

While acute damage (such as that caused by heavy machinery) may be the reason in certain situations, many tanks collapse as a result of wear and tear that has occurred over a long period of time.
In addition to long-term corrosion caused by the gases in the tank, a concrete septic tank can develop fractures over the course of many years of use.
Never go on top of a septic tank just in case it’s leaking or broken.

Leaking untreated wastewater into your yard can expose you and your family to a wide range of germs that are potentially harmful.

If you want to be sure that your tank remains in good condition and does not represent a health and safety threat, having a professional inspection performed once a year is essential.

Drain lines or leach fields that are beginning to deteriorate The pipe system, on the other hand, is another component of your septic system that might pose a threat.

In the event that your septic mainline becomes too old and fails, you may experience a sewage backup problem into your house.

A deteriorating leach field, on the other hand, might cause complications.

The biomat, which is a critical component of water treatment, accumulates with time, decreasing the ability of the leach field to drain away water effectively.

A failing leach field, while not as spectacular as a collapsed tank, can nonetheless result in serious health and safety consequences.

This shows that your septic tank is not the only portion of your system that need regular maintenance if you want to prevent unwanted consequences, including potential dangers to your health and safety.

Don’t forget to follow your septic contractor’s recommendations for the frequency of pumping, inspections, and other routine maintenance, and don’t put off any septic repairs if they are necessary.

Please contact AAA Pumping Service Inc. immediately if you would like more information on septic pumping or any of the other services that we provide. We can assist you with not just pumping services, but also with any sand trap pumping or grease pumping that you may require. Contact us now.

Septic Tank Risers, Lids, and Covers

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered! Would the POLYLOK SEPTIC TANK LID fit directly on the ADAPTER RING, or will I need to use a RISER to ensure a proper fit on the tank? With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength.

Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter.
ALL other Polylok lids will attach straight to the adapter ring, eliminating the need for a riser or any other adaptor.

No.
Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.
It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade.

IS IT BETTER TO USE THE STANDARD LID OR THE HEAVY DUTY LID?
If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended.
Yes.

IS IT INCLUDED WITH THE POLYLOK SEPTIC TANK RISERS AND LIDS TO USE SCREWS?
The Polylok Septic Tank Risers are supplied with screws to allow them to be connected to one another.

THE POLYLOK SEPTIC TANK RISER ADVANTAGE

Riser systems are available in a variety of shapes, sizes, and designs on the market today. The Polylok septic tank risers are, without a doubt, the best money can buy in this category. There are several causes for this, but the following are the most significant:

INTERNAL STRUCTURAL RIBS

The Polylok risers are reinforced with structural ribs that run internally around each riser segment, providing them with exceptional strength and allowing them to maintain their shape even after the hole is backfilled with dirt. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

Because the Polylok products are fully smooth on the outside, they will not cause any problems in frosty environments!

LOW PROFILE RISER LIDS WITH HANDLES

The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE TANK ADAPTER RING

It is necessary to use an adapter ring in order to attach risers to your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

SCREWS INCLUDED

At Septic Solutions, we strive to make the buying and installation process as simple as possible for our customers. All of our Polylok risers and lids are delivered with all of the stainless steel screws required for installation in one package.

How to Care for Your Septic System

Septic system maintenance is neither difficult or expensive, and it does not have to be done frequently. The maintenance of a vehicle is comprised of four major components:

Inspect and pump your drainfield on a regular basis
Conserve water
Dispose of waste properly

And keep your drainfield in good condition.

Inspect and Pump Frequently

Inspection of the ordinary residential septic system should be performed by a septic service specialist at least once every three years. Household septic tanks are normally pumped every three to five years, depending on how often they are used. Alternative systems that use electrical float switches, pumps, or mechanical components should be examined more frequently, typically once a year, to ensure that they are in proper working order. Because alternative systems contain mechanical components, it is essential to have a service contract.

The size of the household
The total amount of wastewater produced
The amount of solids present in wastewater

The size of the septic tank

Service provider coming? Here is what you need to know.

When you contact a septic service provider, he or she will inspect your septic tank for leaks as well as the scum and sludge layers that have built up over time. Maintain detailed records of any maintenance work conducted on your septic system. Because of the T-shaped outlet on the side of your tank, sludge and scum will not be able to escape from the tank and travel to the drainfield region. A pumping is required when the bottom of the scum layer or the top of the sludge layer is within six inches of the bottom of the outlet, or if the top of the sludge layer is within 12 inches of the bottom of the outlet.

In the service report for your system, the service provider should mention the completion of repairs as well as the condition of the tank.

If additional repairs are recommended, contact a repair professional as soon as possible. An online septic finder from the National Onsite Wastewater Recycling Association (NOWRA) makes it simple to identify service specialists in your region.

Use Water Efficiently

In a normal single-family house, the average indoor water consumption is about 70 gallons per person, per day, on average. A single leaking or running toilet can waste as much as 200 gallons of water each day, depending on the situation. The septic system is responsible for disposing of all of the water that a residence sends down its pipes. The more water that is conserved in a household, the less water that enters the sewage system. A septic system that is operated efficiently will operate more efficiently and will have a lower chance of failure.

Toilets with a high level of efficiency. The use of toilets accounts for 25 to 30% of total household water consumption. Many older homes have toilets with reservoirs that hold 3.5 to 5 gallons of water, whereas newer, high-efficiency toilets use 1.6 gallons or less of water for each flush. Replacing existing toilets with high-efficiency models is an easy way to reduce the amount of household water entering your septic system
Faucet aerators and high-efficiency showerheads. Faucet aerators, high-efficiency showerheads, and shower flow restrictors help reduce water use and the volume of water entering your septic system

Washing machines. Water and energy are wasted when small loads of laundry are washed on the large-load cycle of your washing machine. By selecting the proper load size, you will reduce water waste. If you are unable to select a load size, run only full loads of laundry. Try to spread washing machine use throughout the week. Doing all household laundry in one day might seem like a time-saver
But it can harm your septic system, not allow your septic tank enough time to treat waste, and could flood your drainfield Clothes washers that bear theENERGY STARlabel use 35 percent less energy and 50 percent less water than standard models. Other Energy Star appliances provide significant energy and water savings

Properly Dispose of Waste

Everything that goes down your drains, whether it’s flushed down the toilet, ground up in the trash disposal, or poured down the sink, shower, or bath, ends up in your septic system, which is where it belongs. What you flush down the toilet has an impact on how effectively your septic system functions.

Toilets aren’t trash cans!

Your septic system is not a garbage disposal system. A simple rule of thumb is to never flush anything other than human waste and toilet paper down the toilet. Never flush a toilet:

Cooking grease or oil
Wipes that are not flushable, such as baby wipes or other wet wipes

Photographic solutions
Feminine hygiene items Condoms
Medical supplies such as dental floss and disposable diapers, cigarette butts and coffee grounds, cat litter and paper towels, pharmaceuticals, and household chemicals such as gasoline and oil, insecticides, antifreeze, and paint or paint thinners

Toilet Paper Needs to Be Flushed! Check out this video, which demonstrates why the only item you should flush down your toilet are toilet paper rolls.

Think at the sink!

Your septic system is made up of a collection of living organisms that digest and treat the waste generated by your household. Pouring pollutants down your drain can kill these organisms and cause damage to your septic system as well as other things. Whether you’re at the kitchen sink, the bathtub, or the utility sink, remember the following:

If you have a clogged drain, avoid using chemical drain openers. To prevent this from happening, use hot water or a drain snake

Never dump cooking oil or grease down the sink or toilet. It is never a good idea to flush oil-based paints, solvents, or huge quantities of harmful cleansers down the toilet. Even latex paint waste should be kept to a bare minimum. Disposal of rubbish should be avoided or limited to a minimum. Fats, grease, and particles will be considerably reduced in your septic tank, reducing the likelihood of your drainfield being clogged.

Own a recreational vehicle (RV), boat or mobile home?

If you have ever spent any time in an RV or boat, you are undoubtedly familiar with the issue of aromas emanating from sewage holding tanks.

The National Small Flows Clearinghouse’s Septic System Care hotline, which may be reached toll-free at 800-624-8301, has a factsheet on safe wastewater disposal for RV, boat, and mobile home owners and operators.

Maintain Your Drainfield

It is critical that you maintain the integrity of your drainfield, which is a component of your septic system that filters impurities from the liquid that emerges from your septic tank once it has been installed. Here are some things you should do to keep it in good condition:

Parking: Do not park or drive on your drainfield at any time. Plan your tree plantings so that their roots do not grow into your drainfield or septic system. An experienced septic service provider can recommend the appropriate distance for your septic tank and surrounding landscaping, based on your specific situation. Locating Your Drainfield: Keep any roof drains, sump pumps, and other rainfall drainage systems away from the drainfield area. Excess water causes the wastewater treatment process to slow down or halt completely.

Septic Tank Lid

Each compartment of a septic tank is equipped with an access point that is protected by a cover. Depending on the type of tank that is being constructed, they might be made of concrete, plastic, or fiberglass materials. When septic tank lids are sunk more than 12 inches below completed grade during new construction, risers or access tunnels are erected on top of the tank lids and are extended up to a location that is less than 12 inches above the ground surface or to the grade. The most often encountered septic tank lids are the square concrete lids, which measure roughly 21 inches in diameter “.

Because ground water can enter the riser cavity and cause flooding of the tank and whole system, it is critical that the riser be entirely sealed to the tank before it can be used.
Previous Article: Septic Tank Covers—What You Should Know Following Article: Above-Ground Septic System Articles of Interest Providing Exceptional Customer Service.

Call (512) 338-1804 if you need service that is quick and trustworthy.
There are two reasons for this: The.

These allegations have been made for more than 15 years. Maintenance In the case of septic systems, here’s an often overlooked but obvious reality: all septic systems require maintenance to keep them operating properly and to assure their long-term viability.

Septic Tank and Sewer A septic tank is simply one component of a complete on-site wastewater treatment system. Its purpose is to remove solids from the water. Product for Septic Systems It has been formed in a few places throughout the country to create management programs that include having a third-party specialist look at things

Septic Tank Cleaners are those that clean septic tanks. Pumping and cleaning services have just been added to SOS’s list of offerings. The SOS difference is as follows: Our BRAND NEW vehicle has a low mileage
Cleaning of Septic Tanks Septic Tanks Need to Be Cleaned Contractors who specialize in septic tank pumping and hauling can clean your tank. It’s a nice thing
Septic System Maintenance and Repairs ATUs are specifically developed, tested, and/or certified for use with residential wastewater systems. When they are utilized on office buildings, restaurants, and other such establishments

3 Safety Guidelines To Prevent Septic System – Related Injuries And Illness

The following are three safety guidelines to follow in order to avoid septic system-related injuries and illnesses. Because of their widespread use and the fact that they are frequently out of sight, out of mind, septic systems are sometimes taken for granted. Septic systems, on the other hand, can bring death, damage, and sickness in individuals who are not careful and do not follow safety procedures. Three particular principles for safeguarding yourself and anyone who may have access to your land and septic system are outlined in the following sections.

Ensure that the septic tank is accessible.
The drowning of children and some adults in sewage tanks has been reported in the past.

Even though septic tanks are buried beneath the earth, a vertical extension of the tank, known as a riser, is visible above ground, allowing for pumping and maintenance.
Homes without sufficient septic tank protection are frequently abandoned in favor of unsecured lids and coverings, which are readily moved by children and animals.
Locking lids are the most secure since they need the use of a key or a combination to open.

They provide obvious access to the tank while also preventing someone from falling into the tank if the lid is removed accidentally.
Keep maintenance and repair to a minimum by using professionals.

Septic tanks are home to a variety of hidden dangers and lethal traps that must be avoided at all costs.

For example, the natural decaying process of biological waste releases combustible methane, which is dangerous to the environment.

Suffocation is another hazard posed by septic tank failures.

Because none of these gases are oxygenating, a human who is exposed to them may become quickly exhausted and pass out.

Aside from that, avoid leaning over an open septic tank since the gases rising from the tank might lead you to lose consciousness and fall into the tank opening.

Stay away from biological hazards.

While not every germ found in a septic system poses a threat to human health, a large number of disease-causing bacteria, viruses, and protozoa can be found in and near septic systems and should be avoided.

The above-mentioned precaution of staying out of the tank can protect you from being exposed to these microorganisms.

If it is operating properly, the drain field allows liquid effluent from the tank to trickle downhill into the soil, where it is filtered and sterilized before returning to the tank for disposal.

That is why you should avoid walking across a flooded drain field and calling a certified septic service provider, such as Walters Environmental Services, for assistance as soon as possible.

You should not attempt to repair a drain field problem on your own, however you can limit your water use to lower water levels and aid in the drying out of the drainage field.

Residential Septic System Info & Repairs

Line jetting to clear blocked lines and laterals
Repairing or replacing a distribution box
Baffle replacements

Line repairs or replacements
Filters for effluent
Installation of a Riser to Make Servicing Easier

Replacement Lids
Diagnostic Services
And more.

Useful terms:

Septic Tanks: Today, the majority of septic tanks are composed of plastic or concrete. Despite the fact that plastic or fiberglass tanks are resistant to degradation, they are vulnerable to puncture by probing. When identifying tanks, extreme caution should be exercised. Metal tanks have a useful life of around twenty years, however they have not been allowed for new installation for more than thirty years due to safety concerns. Steel tanks deteriorate with time and may collapse during excavation or maintenance work on them.

System components that are not easily accessible, such as the main lid and the baffle cover/lids, might make maintenance more difficult and may cause the system to age more quickly than necessary.
Cesspool: A cesspool is an older type of system that is still in use, but does not satisfy the current regulatory standards for new construction and must be replaced.

There is no separate absorption component to most cesspool systems, such as a pit or field, which makes them more environmentally friendly.
It is recommended that you avoid using heavy equipment or parking cars on top of these lines, since this may cause the lines to break.
Lines can be mended or changed as necessary in order to get the desired pitch.

The input baffle is responsible for all sewage entering the treatment tank from the residence.
if they are degraded or absent, they should be fixed or replaced immediately due to the possibility of difficulties arising from the increased ability of materials to reach the absorption region.
Boxes for distribution: Effluent from the septic tank is distributed into the absorption area through the use of a distribution box (DBox).

If there is evidence of degradation, the dbox should be replaced.
A pit and a field are two types of absorption components that are commonly used.
Septic system flow might be impeded by the presence of roots in the immediate vicinity of the septic system.

The majority of pumps are equipped with an alert that sounds when the pump fails. A wealth of further information may be found on the New Jersey DEP’s Division of Water Quality website, which can be found at: www.state.nj.us/dwq/owm inspect.htm.

How we can help:

We are licensed house contractors in the state of New Jersey. In order to correctly repair all components on your system, Wilson Services System Service have the knowledge and tools to do so. A good solution requires the services of a company that knows the dynamics of your system and can provide a suitable solution for your needs. We can efficiently diagnose and fix any system because of our extensive knowledge. We also offer feedback to the customer on what was done and what may be expected as a consequence of the activities taken.

We are pleased to offer you with a no-obligation quote for any and all repairs to your system!

HOW TO SAFELY ABANDON AN OLD SEPTIC TANK ON YOUR PROPERTY

If you’ve recently purchased an older house, it’s possible that a septic tank is located on the property. This is true even if your home is currently linked to the municipal water and sewer systems. A prior owner may have abandoned the ancient septic system and connected to the city sewage system when it became accessible at some time in the past. Despite the fact that there are standards in place today for properly leaving a septic tank, it was typical practice years ago to just leave the tanks in place and forget about them.

The old tank may either be demolished or filled with water to solve the problem.
It is possible that permits and inspections will be required.
They are dangerous because curious children may pry open the lid and fall into the container.
Falls into a septic tank can be lethal owing to the toxicity of the contents and the fact that concrete can collapse on top of you while falling into a tank.
Eventually, this approach was phased out due to the fact that the steel would corrode and leave the tank susceptible to collapse.
When it comes to ancient septic tanks, they are similar to little caves with a lid that might collapse at any time.
The old tank is crushed and buried, or it is removed from the site.

If it is built of steel, it will very certainly be crushed and buried in its current location.

After that, the tank can be completely filled with sand, gravel, or any other form of rubble and buried.

Tanks can either be entirely dismantled or destroyed and buried in their original location.

The abandonment has been documented and plotted on a map.

It’s possible that you’ll forget about the tank once it’s been abandoned.

As a result, you might wish to sketch a map of the area where the old tank used to stand.

If you can demonstrate that an old septic tank was properly decommissioned, you may be able to increase the value of your property, and the new owners will enjoy knowing that large chunks of concrete are buried underground before they start digging in the yard to put something in it.

It may take some detective work to discover about the history of your land and what may be lying beneath the surface of the earth.

Upon discovering an old septic tank on your property that is no longer in service, contact Total Enviro Services for propertank abandonment procedures that meet with local standards and protect your family, pets, and farm animals from harm or death.

How much should replacing septic tank lids cost, and what is involved?

This is going to be dependent on the type of lids required by the manhole material as well as local codes to a certain extent. For example, in our neighborhood, both concrete manhole covers and bolted-down plastic manhole covers are permissible. In light of the foregoing, if it is simply the lid that need replacement, it shouldn’t be prohibitively expensive in any case. For example, I just upgraded my system by adding a pump tank and a raised drain field. The tanks that were installed had plastic corrugated manholes, and I decided for plastic lids instead of metal ones to save money (the manhole can then be brought down to ground level, and you can mow right over the lid).

Simply put, they employ a 6″ lag screw that is screwed into the plastic manhole cover (if it is a matter of simply replacing existing plastic lids, you can probably do it yourself).
It is impossible for me to say how much the old steel lids cost, although I would think that they are somewhat more expensive.
If the existing lids are made of plastic, just remove the lag screw, take the old lid off, replace it with the new one, and screw the lag screw back in place.
Put the dirt/sod back on top of the pile.

I-TEAM checks septic tank safety at 76 spots around Jacksonville

THE CITY OF JACKSONVILLE, Fla. Several issues have been raised in the wake of the death of a 3-year-old kid who was discovered in an underground sewage tank in a Jacksonville city park, raising concerns about the safety of septic tank systems in areas where children play. Amari Harley died in Bruce Park in Arlington, and the I-TEAM has been working to find answers by visiting all 76 park and boat ramp locations with city-managed sewage and lift stations, including the one where Amari Harley died.

The I-TEAM has sought copies of those inspection reports, but we have not received a response from the city as of this writing.
As a result, we uncovered a number of problems.
Ringhaver Park in southwest Jacksonville, for example, has three different types of septic system covers, which we discovered.
No one could explain why the park has three different sorts of coverings, but the mayor stated that the variances are something he wishes to see changed throughout the city.

According to Curry, “We are going to have a strategy to standardize every single lid, so when we roll out our final assessment, I can tell you I am planning on directing that we standardize the lid process in Jacksonville and all of our parks to ensure that safety is our number one concern.”

Getting results

The I-TEAM discovered a possible hazard at Kathryn Abbey Hanna Park’s beach access when they discovered a tank lid that seemed to be secured with a lock but really had rusted bolts. It required very little effort to remove the lid from the sewage tank, which seemed to be many feet deep and reeked of human waste when I first arrived. Maintenance employees who responded to our call informed us that the lid would be repaired as soon as possible, and they kept their word. Hanna Park’s sewer cover has been repaired.

What we found

While on our travels over the previous week, we discovered that certain parks have gone to great lengths to ensure that septic tank sites are locked up and out of reach of children and people. We noticed a plethora of safety precautions at many of the venues we visited around the city. We were impressed. The septic tanks are protected by metal plates and lockable gates in some cases. It was possible to lock some of the tanks with padlocks, and many parks had secured structures where only specific persons were allowed access to the tanks.

Miller Jr.
Even barriers, though, are not impenetrable.
Some parks, such as the one at the Maxville Athletic Association on the far Westside, have fiberglass tops that are fastened to the ground for further security and stability.
During our investigation of Forestview Park, just south of Soutel Drive in the Harborview neighborhood of northwest Jacksonville, we discovered a system and fiberglass tank lid that seemed to be identical to the one Amari is suspected of having fallen into.
Several of the locations we visited had hefty cement coverings over their septic tanks, which we found to be concerning.
Because there was still dirt surrounding both tank lids, it was obvious that some sort of recent repair had been performed on both.
Some of them were constructed from concrete, while others were constructed from a hard plastic substance.
However, there were two tanks with cement covers near the Mayport boat ramp, including one that easily sprang up when a foot was placed on top of it.
The city informed us that the caution tape was placed on the lid because a bolt was missing.
The maintenance is virtually non-existent.
Some of the parks we attempted to visit were unavailable due to construction.

Because of storm damage, the Tillie K. Fowler Regional Park on the Westside, which has two septic tanks, was forced to lock its doors. The I-TEAM will return to that park when it reopens as part of our ongoing investigation into the safety of septic tanks in area parks.

City response

The mayor has stated that his staff will continue to investigate the situation. When it comes to strengthening, Curry added, “they will strengthen themselves anywhere they can.” On Friday evening, a city spokesperson delivered the following statement to News4Jax: The terrible death of Amari Harley continues to be mourned by the citizens of Jacksonville. Meanwhile, while the JSO conducts its probe, municipal authorities are aiding the JSO and conducting their own inquiry. Hundreds of employees from Parks and Recreation, Public Works, the Mayor’s Office, and ERS (Environmental Remediation Services, Inc.), the contractor who performs monthly inspections of various city-managed septic and lift stations, have been working together to conduct comprehensive assessments and reviews of our existing wastewater systems, practices, and operations.

A number of parks and public facilities that are not on the ERS list but that are managed by the city, such as Forestview, have also been checked out.

While the challenge is enormous, so is the mayor’s passion to public safety and commitment to implementing improved processes, operations, and procedures to do it.

WJXT News4Jax retains ownership of the copyright and reserves all rights.

Septic Tank Safety: Risers & Lids Save Lives

Additionally, the mayor stated that his staff will continue to investigate the situation. When it comes to strengthening, Curry remarked, “they will fortify everywhere they can.” The following statement was issued to News4Jax on Friday night by a city spokeswoman: The terrible death of Amari Harley has left the city of Jacksonville in deep mourning. Meanwhile, municipal authorities are supporting JSO with their probe and conducting their own inquiry. Throughout this week, dozens of staff members from Parks and Recreation, Public Works, the Mayor’s Office, and ERS (Environmental Remediation Services, Inc.), the contractor who conducts monthly inspections of various city-managed septic and lift stations, have been leading comprehensive assessments and reviews of our existing wastewater systems, practices, and operations, according to the city’s wastewater management plan.

In the last week, ERS inspectors went back to each of the 76 locations that had been inspected and found to have faulty septic systems.

In accordance with Mayor Curry’s request for a full and complete audit and assessment of all systems, Parks and Public Works employees are inspecting each and every city park and public facility in order to reaffirm our inventory and assess their current state.

Following the completion of the inventory and assessments, the city and contractors will collaborate to develop standardized operating procedures for all on-site wastewater systems in order to ensure consistency and safety while reducing the likelihood of damage, tampering, or vandalism that could result in injury or harm.” Unless otherwise stated, all rights are retained by WJXT News4Jax in 2017.

Interested in Trucks?

Receive articles, stories, and videos about trucks delivered directly to your email! Now is the time to sign up. Trucks+ Receive Notifications Earlier this month, two good Samaritans came to the aid of a 2-year-old kid who had fallen into a mobile home park sewage tank near Kissimmee, Florida. The youngster had been trapped in the tank for more than an hour when he was rescued. As reported by WFTV.com, the youngster and other prospective victims were exposed to the sewage tank because the lid had not been securely fastened to the tank.

Rafael administered CPR to the youngster, who was subsequently transported to a nearby hospital, where he was examined and released.
Although this tale has a good conclusion, many comparable occurrences involving toddlers who fall into unprotected sewage tanks result in tragic outcomes.
These ground-breaking solutions guarantee that septic tank lids are properly secured and that unlawful tank access is prevented.
The company’s job to ensure that the product is as safe as feasible as a manufacturer of septic system accessories and equipment.
There is also a riser safety screen protection device for use on PVC ribbed pipe, HDPE corrugated pipe, and concrete septic tank risers, which is available from the manufacturer.
The heavy-duty ABS safety screens, which are bright yellow in color, are available in three different sizes: 12, 20 and 24 inches.
There are gaskets and safety hardware incorporated, as well as a safety net option available.

On request, foam-filled lids may be made, and coverings can be made to fit specific needs.

They are available in polyethylene and PVC materials in diameters ranging from 22 inches to 36 inches in 22-, 24-, 26-, 30-, and 36-inch sizes.

The interlocking design of the rims and lids is made possible by a neoprene gasket and a twist lock mechanism.

The ledges will be used to hold the company’s plastic interior safety lids as well as a number of other internal safety devices, such as concrete, fiberglass, or rope netting, manufactured by third parties.

Locking riser lids from Sim/Tech Filter are primarily intended for use on systems that get a lot of traffic.

The web locks and keeps the lid in place in the same action as the web locks and retains the lid.

Water penetration between the riser and the septic tank is prevented by using Seal-r septic tank lids from BrenLin Company, which form a solid seal between the septic tank and the riser.

Increasing need for larger risers to handle modern technological equipment has resulted in the 42-inch lid being introduced.

It weighs only ten pounds, yet it is resistant to harm from lawn equipment and can take a weight of 20,000 pounds without breaking.

Designed for heavy-duty use, the 24 inch septic lid from RotoSolutions Inc.

Designed to accommodate most 24-inch-diameter septic risers and corrugated pipe, the nonskid, kelp green fiberglass riser cover from TOPP Industries is a good choice.

The lid is made of noncorrosive material and can resist a wheel weight of 2,500 pounds. The waterproof and gastight seal provided by the built-in lid gasket is quite effective. Visit for a comprehensive listing of products as well as contact information for the manufacturers.

JSO case file: No child-proof screws on septic tank where 3-year-old died

According to the case file on Amari Harley’s death kept by the Jacksonville Sheriff’s Office, child-proof screws were not put on an underground septic tank where the 3-year-old kid died after drowning. Amari’s gold and black Nike sneaker was discovered floating in the Bruce Park sewage tank before the JSO discovered the boy’s corpse buried face down in the tank. On October 22, 2017, a 3-year-old boy died from asphyxiation caused by inhaling the contents of a septic tank in a public park in Arlington, Virginia.

The day following Amari’s death, Action News Jax reported that the phone number listed on the website did not operate.
According to the case file of the JSO officer who discovered the green rubber septic tank lids were unlocked, “a tiny child might easily have removed them,” according to the officer who discovered them.
However, the city-contracted inspector from Environmental Remediation Services, Inc.
Kay Harper Williams, the attorney representing Amari Harley’s family, expressed her displeasure with the fact that the contractor employed by the city of Jacksonville did not consider it necessary enough to install a child-proof screw at a municipal park where children were present.
Both the Jacksonville Sun-Times and Action News Jax inquired about the city’s monthly inspection reports, but we received conflicting responses.
Overall, the city informed JSO that the lid had been removed from the tank weeks before Amari’s death – information that was not shared with Action News Jax.
And everyone in this community should be asking themselves the same question as well.
In response to Action News Jax’s two emails asking why the city supplied us different information than it did to the Jacksonville Sun-Journal, city spokesman Tia Ford, Director of Public Affairs Marsha Oliver, and city Assistant General Counsel Craig Feiser did not answer.

Terri Durham, who reported that the Bruce Park septic tank lid had been opened in January 2017, described what she observed as a “open hole with no lid over it.” In the words of Williams, “we feel the amount of carelessness that occurred here is criminal.” Since Amari’s death, Ford said, the city has begun erecting metal septic tank lids that are locked in municipal parks to keep the water out.

Ford further stated that the employee who was previously in charge of monitoring septic tank and lift station inspections has been reprimanded and is no longer in the position of supervisor.

Under the amended procedure, these services will be provided in-house, with monthly inspections and repairs of septic tanks being performed by a certified plumber employed by the city.

Amari’s family has already filed a lawsuit against the two city contractors who were responsible for the septic tank’s construction. Williams stated that she intends to file a lawsuit against the city of Jacksonville. Cox Media Group is a media company based in the United States.