How Do I Fill In A Septic Tank? (Perfect answer)

How to Fill in Old Septic Tanks

Ask your local health department to see whether you need a permit to fill the septic tank.
Pump out any water in the septic tank with a water pump.

Remove the lid and destroy it.
Drill holes in all of the side walls and bottom of the septic tank.
Fill the septic tank with dirt or gravel.

Fill the tank with sand or gravel. The sand and gravel allows water to filter through and also fills in the void in case the tank would eventually collapse. Tip Septic tanks should be pumped out by a septic system pumper before attempting to fill in your tank.

How do you fill an old septic tank?

The Old Tank Is Crushed and Buried or Removed If it is made of steel, it will probably be crushed in place and buried. If it is made of concrete, the bottom or sides may be broken apart so the tank can no longer hold water, and then the tank can be filled with sand, gravel, or some other type of rubble and buried.

How do you seal a septic tank outlet?

The tar sealant can be used to fill the void between the concrete and pipe. Use a trowel to press the sealant into the void. If the rubber gasket is molded into the tank for the pipe, tighten it up.

Should I remove old septic tank?

It is important to properly abandon un-used septic tanks, cesspools, or drywells. If an old septic tank, cesspool, or drywell is simply “left alone” there may be very serious cave-in or fall-in safety hazards.

How much sand is needed to fill a septic tank?

BRUISER tanks and cistern tanks should be filled one-fourth full after installation. A. The sand/gravel mixture should be a mixture of sand and gravel, 100% smaller than 1½”, and about 50% smaller than ¼”.

Can you reuse an old septic tank?

In addition to the standard abandonment process of pumping your septic tank and having it rendered useless by filling it with gravel or cement and crushing the tank lids, you have the opportunity to reuse your tank as a cistern.

Where is my septic tank outlet pipe?

The outlet pipe should be approximately 3 inches below the inlet pipe. Inlet Baffle: The inlet baffle is installed on the inlet pipe inside the tank.

What is a septic tank baffle?

Septic baffles are located at the junctions where pipes enter and exit the tank. The one at the inlet pipe is called the inlet baffle, and the one at the outlet is called the outlet baffle. It’s designed to help wastewater flow smoothly into the tank without disturbing the scum layer.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Can septic tanks collapse?

Septic tanks can collapse for a variety of reasons. This is one of the most serious septic tank problems that can occur. Once a tank is emptied of water, it is much more prone to collapse. That is because the pressure of the surrounding soil is no longer counter-acted by the water inside the tank.

What are the signs of a failing septic system?

8 Signs of Septic System Failure

Septic System Backup.
Slow Drains.
Gurgling Sounds.

Pool of Water or Dampness Near Drainfield.
Nasty Odors.
Unusual, Bright Green Grass Above Drainfield.

Blooms of Algae in Nearby Water.
High Levels of Coliform in Water Well.

Is sand good for a septic system?

A sand filter septic system is a good option for wastewater treatment issues in any areas that have insufficient soil. Septic system companies fill in the area with sand to make up for a lack of soil, often by using a large concrete box filled with sand. Above the sand is a layer of gravel with a series of small pipes.

What kind of sand do you use for a septic system?

Septic sand is used as an effective filtration system in modern septic systems and sewage mounds. It is produced from some of the highest quality sand & gravel, which is washed and finely screened.

How to Fill a Septic Tank

Filling a Septic Tank: A Step-by-Step Guide. Many homeowners have made the decision to abandon their old septic system and connect to the municipal sewage system. It is the responsibility of the property owner to properly dispose of their septic tanks once they have been drained out and are no longer in use. Many jurisdictions allow you to keep the tank in the ground rather than having it removed, however it must be filled in for safety concerns in all cases.

Step 1

Filling a Septic Tank – Step by Step Instructions People have made the decision to abandon their old septic systems and connect to the municipal sewage system. Owners are responsible for properly disposing of their septic tanks once they have been emptied out and are no longer in use. It is possible to keep the tank in place rather than having it removed in many regions; however, it must be filled in for safety concerns.

Step 2

A water pump can be rented or purchased from your local hardware shop. Tanks that are more than a decade old have most likely accumulated water and debris that must be removed.

Step 3

Remove any standing water in your septic tank by pumping it away. Due to the fact that all garbage should have previously been drained out prior to the commencement of your operation, the water in the tank should only be rainwater or groundwater.

Step 4

Make holes in the bottom and sides of the tank with a drill or other means of puncturing them. This permits any water that will ultimately find its way back into the tank to be drained out safely.

Step 5

Prepare the tank’s bottom and sides by drilling or puncturing them in various ways. Consequently, any water that will ultimately find its way back into the tank will be able to leave.

Tip

Septic tanks should be emptied out by a professional septic system pumper before you attempt to replenish your tank. In order to determine whether or if a certain local septic system provider provides septic tank filling as a service, you may want to phone around to several companies. It’s possible that they’ll have filling instructions on hand as well.

HOW TO SAFELY ABANDON AN OLD SEPTIC TANK ON YOUR PROPERTY

If you’ve recently purchased an older house, it’s possible that a septic tank is located on the property. This is true even if your home is currently linked to the municipal water and sewer systems. A prior owner may have abandoned the ancient septic system and connected to the city sewage system when it became accessible at some time in the past. Despite the fact that there are standards in place today for properly leaving a septic tank, it was typical practice years ago to just leave the tanks in place and forget about them.

The old tank may either be demolished or filled with water to solve the problem.
It is possible that permits and inspections will be required.

They are dangerous because curious children may pry open the lid and fall into the container.
Falls into a septic tank can be lethal owing to the toxicity of the contents and the fact that concrete can collapse on top of you while falling into a tank.
Eventually, this approach was phased out due to the fact that the steel would corrode and leave the tank susceptible to collapse.

When it comes to ancient septic tanks, they are similar to little caves with a lid that might collapse at any time.
The old tank is crushed and buried, or it is removed from the site.

If it is built of steel, it will very certainly be crushed and buried in its current location.

After that, the tank can be completely filled with sand, gravel, or any other form of rubble and buried.

Tanks can either be entirely dismantled or destroyed and buried in their original location.

The abandonment has been documented and plotted on a map.

It’s possible that you’ll forget about the tank once it’s been abandoned.

As a result, you might wish to sketch a map of the area where the old tank used to stand.

If you can demonstrate that an old septic tank was properly decommissioned, you may be able to increase the value of your property, and the new owners will enjoy knowing that large chunks of concrete are buried underground before they start digging in the yard to put something in it.

It may take some detective work to discover about the history of your land and what may be lying beneath the surface of the earth.

Upon discovering an old septic tank on your property that is no longer in service, contact Total Enviro Services for propertank abandonment procedures that meet with local standards and protect your family, pets, and farm animals from harm or death.

How Long Does It Take for Septic Tanks to Fill Up?

Whatever your situation is, whether you have just completed the installation of a new septic tank or are wondering when it is time to do periodic maintenance on your existing underground septic tank, it is critical that you understand how the tank works and when, if at all, it becomes full. The topic of how often you should pump your septic tank or how long it takes for a septic tank to fill up has been questioned for some years now, and the answer is: it depends. Some allege that they didn’t know or just didn’t care to pump their tanks, while others believe that a policy should be in place defining when and how to do so should be implemented.

It should be noted that this is a highly subjective response.

Let’s take a closer look at each of these criteria to see if your septic tank is approaching capacity.

Understanding How a Septic Tank Fills Up

There is a direct relationship between the amount of food consumed in a home and the amount of garbage created in that household. Adults generate around one liter of garbage every day, which equates to 90 gallons of waste per year on average. Not all of this garbage ‘fills up’ a septic tank, as the expression goes. The waste is reduced to around 60% of its original volume in the tank. It is recommended by both regulatory agencies and the pumping industry that you should not allow the sludge/scum layer at the bottom of your tank to occupy more than 30% of the total capacity of your septic tank.

After the 305-mile threshold, the procedure gets significantly slower, resulting in a significantly faster filling of the tank.

All of these figures are based on a single individual filling a 1,000-gallon septic tank with sewage.

As youngsters get older (and reach school age), the length of this time period will shorten.

Rooms	Minimum Size
3	900 gallons
4	1,250 gallons
5	1,400 gallons
6	1,550 gallons
6	2,000 gallons

The smallest septic tank size that is suggested for a certain number of rooms. According to these estimates (which are supported by multiple state-wide studies), it is reasonable to conclude that a septic tank should be pumped once every two to three years. There is just one primary duty for every septic tank, and that is to collect sludge that would otherwise be difficult to deal with while distributing cleaned water to the land underneath the tank via drain fields.

The lighter and more floatable particles are ultimately responsible for filling the tank.

What Happens Whenthe Septic Tank Fills Up?

As previously said, many people claim that they have never had to pump their septic tank before, although it appears to be ‘functioning normally.’ In fact, the reason for this is that when an increasing amount of settled and floating organic material is added to the septic tank, certain particles begin to escape. When the tank is full and there is no more space for the tank to absorb and hold solids, particles begin to leak through the tank’s walls and into the water. These are particles that have accumulated at the bottom or near the drain pipes for an extended period of time and have grown soft enough to flow with the water.

Eventually, these particles reorganize themselves to block the soil absorption region, resulting in backflowing toilets and gutters. Alternatively, small solid particles may escape due to the pressure put on the bottom layer of the soil (because of its weight). Your property will initially have a strong scent that passersby and guests will notice
But, over time as these particles continue to sink into the soil, your property will develop an unpleasant odor that both passersby and guests will notice.

This is why it is critical to get your septic tank pumped on a regular basis.

Can I Shower If My Septic TankIs Full?

If your septic tank is completely full, you CAN take a shower. Slow drainage is the only issue you’re likely to encounter in this situation. The water in your shower, tub, sink(s), and other fixtures will begin to drain much more slowly as your septic tank continues to fill up with waste. Although this is true in certain cases, it is crucial to remember that shower drains do not run to septic systems, but rather straight into sewage lines, because there is no solid waste contained inside them.

However, because this is only liquid water, you will not be causing as much harm to your septic tank as you might otherwise be if the water were to enter it.

Will My Toilet FlushIftheSeptic TankIs Full?

Your toilet should continue to flush regularly until your septic tank is full to 90 percent capacity. After then, you will notice that the toilet begins to behave in an unusual manner. Either the toilet may flush very slowly or the drain will begin to make strange sounds, depending on the situation (such as passing gas or gurgling). It is fairly unusual for the toilet to begin to bubble. The problem can be solved with a band-aid approach, but keep in mind that this is simply a short-term remedy.

Alternatively, some acid can be used to achieve the same results.

If you flush the toilet, you should be able to pump your tank without experiencing any severe difficulties for a number of days.

Signs ThatItIs Timeto PumpaSeptic Tank

It is always possible to use the “cross that bridge when we get there” approach if you are unable to predict how long it will take for septic tanks to fill up completely. In order to do so, you must be aware of the indicators of a clogged septic tank.

It is possible to just open the tank and have a look inside (DO NOT TRY THIS AT HOME). Afterwards, you’ll almost certainly become ill and spend the following several days in bed – or even worse, in the hospital. You have two alternatives if you want to be on the safe side:

The policy of “crossing that bridge when we get there” might be adopted if you are unable to predict how long it will take for septic tanks to fill up. Knowing the indicators of a clogged septic tank is essential for this. It is possible to just open the tank and have a look inside (DO NOT TRY THIS). It is very likely that you will have an illness, which will need you to spend the next several days in bed – or worse, in the hospital. You have two alternatives if you want to be on the safe side: (1)

An illustration of a common septic tank configuration You should have your tank pumped every 2 to 3 years, unless you are a professional plumber who knows what they are doing.

Septic Tank Pumping Process

A pipe that runs through a septic tank to allow it to be emptied. Hire septic tank pumping contractors and delegate the task to them; this is the best course of action for everyone, including do-it-yourselfers. Keep in mind that you are not only responsible for pumping the waste, but also for transporting it to the appropriate facility. The procedure begins by removing the scum layer that has formed on top of all of the sludge. The sludge, on the other hand, is unable to be pushed out properly.

The chemicals eat away at the sludge, causing it to shrink in bulk.

The fact that there isn’t enough liquid in the container indicates that you have filled it to the recommended level.
Mixing is accomplished with the assistance of a pump, or by simply pumping liquid into a container, withdrawing it, and pouring it back into the container.
The septic system must be pumped through the two access ports seen in the picture above to function properly.

Once the water has been drained out, it is typical for specialists to inspect the area for damage.

DIY Septic Tank Abandonment: Money-Saver or Potential Danger?

Septic tank drainage is accomplished by means of a pipe within the tank. Septic tank pumping contractors are the greatest option, even for do-it-yourselfers, because they can handle the job efficiently. Not only must it be pumped, but it must also be transported to the appropriate disposal site. In order to begin, the scum layer on top of all of the sludge must first be broken down by mechanical means. While it may be possible to properly pump away sludge, this is not the case in this case. Additives are then used by professionals to remove as much sludge as possible from the water supply.

Afterwards, water is introduced to the tank, or the liquid component of the tank is blended with the water.

Adding water from the top will be required in that situation.

This ensures that all of the sludge is properly incorporated into the liquid solution.

Manholes are what these are essentially (not the smaller one that is used for inspection, above the baffle). When a professional has finished pumping out the water, it is customary for them to inspect the water for damage. It is decided at this time whether or not any repairs are required.

Septic tanks have the potential to harbor disease-causing organisms, resulting in severe sickness. A number of bacterial illnesses, as well as Tetanus, Hepatitis A, Leptospirosis, and gastrointestinal sickness, are notably mentioned in InspectApedia. Septic tanks frequently contain toxic and flammable gases, such as methane (CH4) and hydrogen sulfide (H2S), which can cause fires. In 2016, a Florida family narrowly escaped with their lives after their septic tank ruptured, destroying their home and causing it to burn to the ground.

Location, Location, and still another location Finding the leach field (the system that disposes of human waste) is a very other story. While you may be aware of the location of the septic tank or may be able to locate it with the use of a metal detector, exposing the septic tank is a completely different story. In order to locate it, you’ll need to map ground conductivity (which is generally different from the rest of the soil) or use Ground Penetrating Radar (GPR) to locate it (GPR). Unless you have the correct gear, you might end yourself digging aimlessly in the wrong place—or being misled; inaccuracies in metal detector readings have been known to occur at older houses where numerous generations of pipes and cables have been buried over time.

Others, for example, will just fill the tank with sand, gravel, or concrete without first making punctures in the bottom and sides of the tank.
Another concern for do-it-yourselfers.

Look no farther than the DIY Chatroom, an online community where handymen warn one another about the dangers of trying a DIY pump installation.
The only way you can clean it is to hire a professional.
And if you’re ready to call in the specialists right away, get in touch with the knowledgeable pros at Express SewerDrain right now.

Misconceptions of Septic Systems

You never have to have the septic tank pumped.As the septic system is used, the solids (sludge) accumulate on the bottom of the septic tank(s). When the sludge level increases, sewage has less time to settle properly before leaving the tank through the outlet pipe and a greater percent of suspended solids escape into the absorption area. If sludge accumulates too long, no settling of the solids will occur, and the solids will be able to directly enter the absorption area. These solids will clog the distribution lines and soil and cause serious and expensive problems for the homeowner. To prevent this, the tank must be pumped out on a regular basis.If you use additives you don’t have to have the tank pumped.The claims made by companies that sell additives are that you never have to pump your tank. What the products do is break up the scum and sludge so that there is a greater percent ofsuspended solidsin the tank that then flow down the over flow pipe with the effluent to your absorption area, causing your system to fail.The absorption area is designed to treat water or effluent, not solids.The septic tank is designed to contain and treat the solids and they should remain in the tank. It is much less costly to pump your tank on a routine basis than ultimately having to replace your absorption area.It takes years between having the tank pumped for the septic tank to fill to its capacity.The average usage for a family of four will fill a septic tank to its working capacity of 1000 – 1500 gallons in approximately one week. When the contents (liquids and solids) in the tank reaches the level of the overflow pipe, the effluent flows down the overflow pipe to the absorption area every time water is used in the house.The tank works at this full level until it is emptied when it is pumped again.When the alarm for the pump sounds it means you need to pump your tank.If you have a system designed with a pump to pump the effluent to the absorption area you also have an alarm for the septic system.The alarm sounds when the water level rises in the pump tank and alerts you that there is a malfunction with your pump, float switches, or other component in the pump tank.It does not mean that it is time for a routine pumping of your tank.

Proper Backfill for Septic Tanks

Receive articles, stories, and videos about septic tanks delivered directly to your email! Now is the time to sign up. Septic Tanks and More Receive Notifications After a septic tank has been installed, it must be backfilled in the proper manner. Backfilling all tanks with successively tamped “lifts” or depth increments of consistent gradation should be the standard procedure. The installer should ensure that the backfill material is devoid of clods, big boulders, frozen stuff, and debris, all of which can cause voids in the backfill material, which may enable the foundation to settle over time.

Each layer should be homogeneous in thickness, no more than 24 inches thick, and of roughly identical heights around the perimeter of the tank, with the exception of the top layer.
If the material being used is compactable, it should be compacted in order to prevent the earth surrounding the tank from sinking.

Backfill the tank with granular material until it reaches at least the midseam of the tank to ensure that settling is kept to a minimum.
Fill around a septic tank that has been compacted All pipe penetrations through all tanks must remain waterproof after the tanks have been refilled with water.
In order to provide a stable foundation for the pipe, the backfilled earth should be tapped.

Pipe joints should be laid atop native soil rather than in the excavation to avoid the risk of their settling in the future.
It is possible to sleeve pipes that may run over the top of the tank or through excavated portions (such as electrical conduit and/or return lines) to give additional support.

It is possible that the manufacturer of a nonconcrete tank will recommend or require that the tank be simultaneously filled with water to just above the backfill level in order to avoid uneven or excessive pressure on the tank walls during the installation process and to reduce the risk of the tank shifting position during installation.

It may be required to use a tamping tool to ensure that backfill makes adequate contact with and between tank ribs, but care must be given to prevent harming the tank during the process.

She has a master’s degree in civil engineering and a doctorate in environmental engineering.

Her responsibilities include serving as the education chair for the Minnesota Onsite Wastewater Association and the National Onsite Wastewater Recycling Association, as well as serving on the National Science Foundation’s International Committee on Wastewater Treatment Systems.

Send an email to [email protected] if you have any concerns concerning septic system care and operation. Heger will respond as soon as possible.

Septic Tank Pumping

Septic tanks are used in the vast majority of on-lot sewage systems nowadays. The subject of how frequently a septic tank should be pumped has been a source of contention for several decades. For example, there are some homeowners who say they have never drained their septic tank and that it “appears” to be in fine working condition. While trying to establish a standard pumping strategy, authorities have taken a more conservative approach and have declared that all septic tanks should be pump out every two to three years.

How a Septic Tank Works

Box 1.Can you tell me how much solid trash you generate? The average adult consumes around one quart of food every day. The body removes just a very little percentage of this meal and utilizes it to provide energy for the body’s functions. The remaining portion is discharged into the waste water system. This translates into around 90 gallons of solid waste being discharged into the septic tank per adult each year. Based on the assumption that the anaerobic bacteria in the septic tank reduce the waste volume by around 60%, this indicates that each adult contributes approximately 60 gallons of solids to their septic tank each year.

Consequently, it will take around 5 years for one adult to completely fill a 1,000-gallon septic tank with sludge and scum, which is approximately 300 gallons.
It is simple to infer that a septic tank should be pumped every two to three years after accounting for adults who work outside the home for a third of the time and children who attend school after making these modifications to the study.
Single chamber septic tanks were the most common type of septic tank until recently.

Septic tanks are designed to aid the removal of particles that are heavier than water by encouraging these heavy particles to settle to the tank bottom, resulting in the formation of the sludge layer.
It is also designed to keep particles that are lighter than water by encouraging these lighter particles to float to the surface and be maintained in the tank, resulting in a layer of scum on the surface of the tank.

In part, this is due to the fact that the temperature of the septic tank is equal to that of the soil surrounding it, and the anaerobic bacteria require higher temperatures in order to effectively decompose organic material in wastewater and thus reduce the biological oxygen demand (BOD) of the wastewater.

Holding on to the heavy (settleable) and lighter (floatable) particles allows the septic tank to gently fill with solids from the bottom up as well as from the top down.
Septic tanks with an exit filter will catch and decrease the flow of solids into the absorption area when the tank is properly designed and installed.
As a result, it is critical that every septic tank be pumped on a regular basis to eliminate the organic particles that have been collected and partially digested.

Small amounts of the particles kept in the tank degrade, but the vast majority of the solids stay and build up in the tank.
Under no circumstances should you enter a septic tank.
With continued usage of the on-lot wastewater disposal system, an accumulation of sludge and scum builds up in the septic tank.

As the amount of sludge and scum in the tank fills up, wastewater is maintained in the tank for a shorter period of time, and the solids removal process becomes less efficient as a result.

It is necessary to pump the tank on a regular basis in order to avoid this. Asseptage is the term used to describe the substance injected. Cross-sectional view of a two-chamber septic tank (Figure 1).

Number of bedrooms in the home	Estimated daily flow (gallons/day)	Minimum septic tank size (gallons)
3	400	900
4	500	1,250
5	600	1,400
6	700	1,550

How Frequent should a Septic Tank be Pumped?

Pumping frequency is determined by a number of parameters, including:

The capacity of the septic tank

The amount of wastewater that is put to the septic tank each day (see Table 1)
The amount of solids in a wastewater stream is measured. In this regard, it should be noted that there are various different types of particles that are regularly dumped into a septic system. This group of solids includes (1) biodegradable “organic” solids such as feces (see Box 1), (2) slowly biodegradable “organic” solids such as toilet paper and cellulosic compounds, which take a long time to biodegrade in the septic tank, and (3) non-biodegradable solids such as kitty litter, plastics, and other non-biodegradable materials, which do not biodegrade and quickly fill the septic tank It is possible to significantly reduce the quantity of slowly biodegradable organics and non-biodegradable trash that is introduced to your septic tank by reducing the amount of organic waste that is added to the tank.

Another factor that influences how soon a septic tank will fill with solids is one’s way of living. In terms of septic tank function, the two most essential aspects of one’s lifestyle are as follows: Homes with expanding families, having children ranging in age from tiny children to adolescents, often consume more water and deposit more sediments into the septic tank than other types of households. Empty nesters, and especially the elderly, on the other hand, have a tendency to consume significantly less water and to deposit significantly less solid waste in septic tanks.

The particles in a septic tank tend to be taken away from the tank to the soil absorption region, as previously indicated.
As additional materials collect in the absorption region, these sediments begin to choke the soil, preventing wastewater from being able to fully absorb.
In most cases, the removal of these biomats is both expensive and time-consuming.

Pumping the wastewater that has accumulated in the soil absorption area is required for the removal of the biomat.
The biomat normally decomposes within a few days after the absorption area has been completely dewatered and has been aerated.

Is It Time To Pump Your Septic Tank?

So, how does one go about determining how frequently a septic tank needs be cleaned? We are aware that residences who dispose of huge volumes of non-biodegradable and slowly biodegradable organic waste into their septic tank require more frequent pumping. It is also known that prior to the time at which the collected solids have accumulated to the point that they are being taken with the tank effluent to the absorption region, the septic tank should be pump out. When it comes to determining when (and how frequently) to pump your septic tank, there are two generally safe ways to use.

The alternative method is to open the access port to the first chamber (as shown in Figure 1) once a year and insert a long pole to the bottom of the tank and then pull it out of the tank.

If the sludge has accumulated to more than one-third of the tank’s total depth, it is time to have it drained out completely. The majority of households will benefit from having their tanks drained every two or three years instead.

The Pumping Process

Contractors who specialize in septic tank pumping and hauling may pump your septic tank. It is a good idea to be present to check that everything is completed correctly. For the material to be extracted from the tank, it is necessary to break up the scum layer, and the sludge layer must be combined with the liquid section of the tank. In most cases, this is accomplished by alternately pumping liquid out of the tank and re-injecting it into the bottom of the tank. Not the little intake or outlet inspection openings situated above each baffle, but the two huge central access ports (manholes) are required for pumping the septic tank.

It is not suggested to use additives in septic tanks to minimize the volume of sludge or as a substitute for pumping in order to achieve these goals.

When you have your septic tank pumped, you should consider taking an additional step to ensure that your septic system continues to perform correctly for a long time.
This inspector can tell you whether or not your septic tank needs to be repaired, as well as whether or not other components of your sewage system require upkeep.
Mark the position of the tank as well, so that it may be found simply in the future for pumping.

Schedule Septic Tank Pumping

Homeowners should develop the practice of getting their septic tanks drained on a regular basis. As long as you are able and willing to schedule regular septic tank pumping (every two or three years, for example), it may be feasible to improve the overall performance of your complete on-lot wastewater disposal system. According to research conducted at Penn State, your soil absorption system will benefit from frequent resting periods (a period during which no wastewater is added to the absorption area).

In other words, the whole system, particularly the soil absorption region, will have the opportunity to dry up, and any organic waste (biomat) that may have formed in the soil absorption area will degrade swiftly in the absence of water.

Summary

A septic tank is simply one component of a complete on-site wastewater treatment system. Its purpose is to remove solids from the effluent prior to it reaching the soil absorption region, to allow for the digestion of a part of those solids, and to store the remainder of the solids in a holding tank. It is not necessary to use biological or chemical additions to enhance or speed the breakdown process.

Grinders contribute to the solids load on the system by reducing the size of garbage. Solids must be removed on a regular basis in order to prevent them from accessing the soil absorption zone. Every two to three years, you should have your septic tank drained and examined by a professional.

For additional assistance contact

Your local Sewage Enforcement Officer or Extension Educator can help you with these issues. A contact for the Pennsylvania Association of Sewage Enforcement Officers (PASEO) is as follows:4902 Carlisle Pike,268Mechanicsburg, PA 17050 Phone: 717-761-8648 Email: [email protected] Philadelphia, PA 18016 717-763-7762 [email protected] Pennsylvania Septage Management Association (PSMA)P.O. Box 144 Bethlehem, PA 18016 717-763-7762

Why Your Septic Tank Looks Full After Pumping – Septic Maxx

Septic tanks must be pumped on a regular basis in order to maintain an effective and healthy system. You’ve probably peered inside your tank after it’s been pumped and wondered why the water level is still so high. When you see a high water level, it might be alarming, especially if you are not familiar with what happens throughout the pumping process. What you need to know about your septic tank is outlined here.

Water is Necessary

Pumping a septic tank removes the solid waste or sludge from the tank’s bottom, allowing it to function properly. Excessive sludge in a septic tank can find its way through the outlet and into the drain field pipes, causing severe flooding in the surrounding area. Not everyone is aware that there is a specified operating level for all septic tanks, which may be found here. 8 to 12 inches from the top of the septic tank’s lid should indicate that the tank is “full.” This might vary based on the size and kind of septic tank used.

When the water level in your tank exceeds the capacity of the pipe, your tank is considered to be overfilled.

You should get your septic system examined and water usage should be restricted until an expert can determine the source of the problem.

What Can Cause Your Septic Tank to Overfill

There might be a variety of factors contributing to your septic tank being overfilled. The presence of an overfilled septic tank is frequently a symptom that your drain field is not operating properly. The drain field is the final fixture in the septic system, and it is responsible for returning treated wastewater to the surrounding soil. When your drain field floods, the water flow becomes obstructed, causing the water level in your septic tank to increase significantly. Plumbing problems and excessive water use are two more prevalent problems.

Excessive water use might cause the septic tank to fill with more contents than it is capable of handling, resulting in a high water level.

Septic Maxx provides high-quality solutions that effectively tackle the problems that afflict septic tanks.

Our environmentally friendly premium products are biodegradable and may be used to clean your septic tank of unwanted build-up by simply flushing them down the toilet that is the furthest away from your septic tank. Get in touch with us to talk with a septic specialist right now.

How Does a Septic Tank Work?

Mr. Fix-It-Up-For-The-Family You may save a lot of money if you understand how a sewage treatment system works—and what can go wrong—so that you can handle your own septic system maintenance.

How does a septic tank work?

Pumping the tank on a regular basis eliminates sludge and scum, which helps to keep a septic system in good working order. It is possible for a well-designed and well built septic system to last for decades, or it might collapse in a matter of years. It is entirely up to you as long as you can answer the question of how do septic tanks function. Healthy septic systems are very inexpensive to maintain, but digging up and replacing a septic system that has completely collapsed may easily cost tens of thousands in labor and material costs.

It’s critical to understand how a septic tank works in order to maintain one.

Let’s take a look below ground and observe what happens in a properly operating septic system, shall we?

Understand that a septic system is a cafeteria for bacteria

Bacteria are responsible for the proper operation of a septic system. They decompose garbage, resulting in water that is clean enough to safely trickle down into the earth’s surface. The entire system is set up to keep bacteria healthy and busy at all times. Some of them reside in the tank, but the majority of them are found in the drain field. 1. The septic tank is the final destination for all waste. 2. The majority of the tank is filled with watery waste, referred to as “effluent.” Anaerobic bacteria begin to break down the organic matter in the effluent as soon as it enters the system.

A layer of sludge settles to the bottom of the container.
4.
Scum is mostly constituted of fats, greases, and oils, among other substances.

Grease and oils float to the surface of the water.
(5) A filter stops the majority of particles from reaching the exit pipe.
The effluent is discharged into the drain field.
Effluent is allowed to leak into the surrounding gravel because of holes in the drain septic field pipe.
The garbage is completely decomposed by aerobic bacteria found in gravel and dirt.
Potable water seeps into the groundwater and aquifer system from the surface.

Septic Tank Clean Out: Don’t abuse the system

Septic systems that have been correctly planned and constructed require just occasional ‘pumping’ to remove the sludge and scum that has built up inside the tank.

However, if you don’t understand how a septic tank works, you may unintentionally hurt or even destroy the system.

Drains are used to dispose of waste that decomposes slowly (or not at all). Cigarette butts, diapers, and coffee grounds are all known to cause issues. Garbage disposers, if utilized excessively, can introduce an excessive amount of solid waste into the system. Lint from synthetic fibers is emitted from washing machine lint traps. This substance is not degraded by bacteria in the tank and drain septic field. Bacteria are killed by chemicals found in the home, such as disinfecting cleansers and antibacterial soaps. The majority of systems are capable of withstanding limited usage of these goods, but the less you use them, the better. When a large amount of wastewater is produced in a short period of time, the tank is flushed away too quickly. When there is too much sludge, bacteria’s capacity to break down waste is reduced. Sludge can also overflow into the drain field if there is too much of it. Sludge or scum obstructs the flow of water via a pipe. It is possible for tree and shrub roots to obstruct and cause harm to a drain field. Compacted soil and gravel prevent wastewater from seeping into the ground and deprive germs of oxygen. Most of the time, this is caused by vehicles driving or parking on the drain field.

Get your tank pumped…

Your tank must be emptied on a regular basis by a professional. Pumping eliminates the accumulation of sludge and scum that has accumulated in the tank, which has caused the bacterial action to be slowed. If you have a large tank, it may be necessary to pump it once a year; but, depending on the size of your tank and the quantity of waste you send through the system, you may go two or three years between pumpings. Inquire with your inspector about an approximate guideline for how frequently your tank should be pumped.

…but don’t hire a pumper until you need it

Inspections and pumping should be performed on a regular basis. However, if you’re not afraid of getting your hands dirty, you may verify the sludge level yourself with a gadget known as The Sludge Judge. It ranges in price from $100 to $125 and is commonly accessible on the internet. Once you’ve verified that your tank is one-third full with sludge, you should contact a professional to come out and pump it out completely.

Install an effluent filter in your septic system

Garbage from your home accumulates into three distinct strata. The septic filter is responsible for preventing blockage of the drain field pipes.

Septic tank filter close-up

Garbage from your home is deposited in three layers: Septic filters are designed to prevent blockages in the drain field pipes.

Solution for a clogged septic system

If your septic system becomes clogged and you find yourself having to clean the filter on a regular basis, you might be tempted to simply remove the filter altogether. Hold on to it. Solids, wastewater, and scum are separated into three levels in septic tanks, which allows them to function properly (see illustration above). Solids sink to the bottom of the container, where microbes breakdown them. The scum, which is made up of trash that is lighter than water, rises to the surface. In the drainage field, the middle layer of effluent leaves the tank and goes through an underground network of perforated pipes to the drainage field.

Keep the effluent filter in place since it is required by your state’s health law.
Waste particles might flow through the filter and clog the perforated pipes if the filter is not used.
Your filter, on the other hand, should not require cleaning every six months.
A good chance is high that you’re flushing filter-clogging things down the toilet, such as grease, fat, or food scraps.
A garbage disposal will not be able to break down food particles sufficiently to allow them to flow through the septic tank filtration system.
Plastic items, disposable diapers, paper towels, nonbiodegradable goods, and tobacco products will clog the system if they are flushed through it.

For additional information on what should and should not be flushed down the toilet, contact your local health authority. More information on removing lint from your laundry may be found here.

Get an inspection

Following a comprehensive first check performed by an expert, regular inspections will cost less than $100 each inspection for the next year. Your professional will be able to inform you how often you should get your system inspected as well as how a septic tank functions. As straightforward as a septic system appears, determining its overall condition necessitates the services of a professional. There are a plethora of contractors who would gladly pump the sludge out of your tank, but many, in my experience, are unable to explain how a septic system works or how it should be maintained.

A certification scheme for septic contractors has been established in certain states; check with your state’s Secretary of State’s office to see whether yours is one of them.

Also, a qualified inspector will be able to tell you whether or not your tank is large enough to accommodate your household’s needs, as well as the maximum amount of water that can be passed through it in a single day.

As you learn more about how a septic tank works, your professional should be able to tell you whether or not your system will benefit from this treatment.

Alternatives to a new drain field

If an examination or a sewage backup indicate that your drain field is in need of replacement, the only option is to replace it completely. As a result, it’s important to talk with a contractor about other possibilities before proceeding with the project.

Pipes should be cleaned. A rotating pressure washer, used by a contractor, may be used to clean out the drain septic field pipes. The cost of “jetting” the pipes is generally around $200. Chemicals should be used to clean the system. A commercial solution (not a home-made one) that enhances the quantity of oxygen in the drain field should be discussed with your contractor before installing your new system. Septic-Scrub is a product that I suggest. A normal treatment will cost between $500 and $1,000. Make the soil more pliable. The practice of “terra-lifting,” which involves pumping high-pressure air into several spots surrounding the drain field, is authorized in some regions. Some contractors use it to shatter compacted dirt around the pipes. Depending on the circumstances, this might cost less than $1,000 or as much as $4,000 or more.

Protect your drain septic field from lint

When this device is in place, it inhibits lint from entering the system, especially synthetic fibers that bacteria are unable to digest. One of these filters, which I’ve designed and termed theSeptic Protector, was invented by me. An additional filter is included in the price of around $150 plus delivery. Learn more about how to filter out laundry lint in this article.

Don’t overload the septic system

Reduce the amount of water you use. The volume of water that flows into your tank, particularly over a short period of time, can be reduced to avoid untreated waste from being flushed into your drain field. Replace outdated toilets with low-flow ones, install low-flow showerheads, and, perhaps most importantly, wash laundry throughout the week rather than just on Saturday mornings to save water.

Meet the Expert

Septic systems, according to Jim vonMeier, are the solution to America’s water deficit because they supply cleaned water to depleted aquifers, according to vonMeier. He travels the country lobbying for septic systems, giving lectures, and giving testimony. For septic system inquiries, as well as information on the operation of the septic tank, contact him by email.

How Your Septic System Works

As a result of its ability to supply filtered water to depleted aquifers, Jim vonMeier believes that septic systems are the solution to America’s water deficit.

As an advocate for septic systems around the country, he speaks at conferences, gives lectures, and appears in court. For septic system inquiries, as well as information on the operation of the septic tank, contact him through email or letter.

Specifically, this is how a typical conventional septic system works:

All of the water that leaves your home drains down a single main drainage pipe and into a septic tank. An underground, water-tight container, often composed of concrete, fiberglass, or polyethylene, serves as a septic system’s holding tank. Its function is to retain wastewater for a long enough period of time to allow particles to sink to the bottom and form sludge, while oil and grease float to the surface and produce scum. Sludge and scum are prevented from exiting the tank and moving into the drainfield region by compartments and a T-shaped outlet. After that, the liquid wastewater (effluent) exits the tank and flows into the drainfield. The drainfield is a shallow, covered hole dug in unsaturated soil that serves as a drainage system. Porous surfaces are used to release pretreated wastewater because they allow the wastewater to pass through the soil and into the groundwater. In the process of percolating through the soil, wastewater is accepted, treated, and dispersed by the soil, finally discharging into groundwater. Finally, if the drainfield becomes overburdened with too much liquid, it can flood, causing sewage to flow to the ground surface or resulting in toilet backups and sink backups. Finally, wastewater percolates into the soil, where it is naturally removed of harmful coliform bacteria, viruses, and nutrients. Coliform bacteria are a kind of bacteria that may be found in the intestines of humans and other warm-blooded animals, with humans being the most common host. As a result of human fecal contamination, it is a sign of this.

The Guadalupe-Blanco River Authority has built an animated, interactive model of how a residential septic system works, which you can view here.

Do you have a septic system?

It’s possible that you’re already aware that you have a septic system. If you are not sure, here are some tell-tale symptoms that you most likely are:

You make use of well water. In your home, the water pipe that brings water into the house does not have a meter. In the case of a water bill or a property tax bill, you will see “$0.00 Sewer Amount Charged.” It is possible that your neighbors have a septic system

How to find your septic system

You can locate your septic system once you have confirmed that you have one by following these steps:

Taking a look at the “as constructed” drawing of your house
Making a visual inspection of your yard for lids and manhole covers
Getting in touch with a septic system service provider for assistance in locating it

Failure symptoms: Mind the signs!

A bad odor is not necessarily the first indicator of a septic system that is failing to work properly. Any of the following signs should prompt you to seek expert assistance:

Water backing up into the drains of homes and businesses
It is especially noticeable in dry weather that the drainfield grass is bright green and spongy. The presence of standing water or muddy soil near your septic system or in your basement
A strong stench emanating from the area surrounding the septic tank and drainfield