Where Is The Septic Tank In Relation To The Cleanout? (Best solution)

How Do I Find My Septic Tank Cleanout? When locating the home’s sewer line and where it leads out of the home, there will often be a cap that can be removed. This is where a cleanout for the sewer line that connects from home to the septic tank is located.

• How far is the septic tank from the cleanout? Building codes typically require that the tank be located 10′ or more from the building so 4′ is a bit close but at some old properties we’ve found the septic tank right next to the foundation wall of the house.

How do I find out where my septic tank is located?

Follow the Main Sewer Line Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside. The sewer pipes will lead to where your septic tank is located.

Where are most septic tanks located?

Toe the Line. Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.

Can you pump a septic tank from the cleanout?

No. Even if a hose could fit down the cleanout, this still would not provide a thorough cleaning. The tank should be pumped from the actual access lid(s) on the tank, which are usually buried 6-12 inches below the surface of the ground.

How far apart are septic Cleanouts?

Cleanouts shall be installed not more than 100 feet (30 480 mm) apart in horizontal drainage lines measured from the upstream entrance of the cleanout.

How do you tell if your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

1. Your Drains Are Taking Forever.
2. Standing Water Over Your Septic Tank.
3. Bad Smells Coming From Your Yard.
4. You Hear Gurgling Water.
5. You Have A Sewage Backup.
6. How often should you empty your septic tank?

How do septic tanks look?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

Should septic tank lids be buried?

In most cases, all components of the septic tank including the lid are buried between 4 inches and 4 feet underground. Unless the septic tank has special risers that position the lid at ground level, you’ll have to dig for it.

Will metal detector find septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

Where does a septic tank get pumped from?

Rather than pumping waste through sewer mains to a central sewage treatment facility, a septic system pumps solid and liquid waste from the house out into a drain field and underground septic tank.

What is a septic tank cleanout?

The septic systems cleanout is the short PVC pipe with removable cap that sticks out of the ground between your house and the septic tank. If the cleanout does contain backup, it could be from the septic system or it could be a blockage between the cleanout and the tank.

What to do after septic tank is pumped out?

After you have had your septic tank pumped by a trusted septic company, there are some things you can and should do as the septic system owner.

1. 1) Get on a Schedule.
2. 2) Take Care of the System.
3. 3) Know the Parts of Your System.
4. 4) Check Other Possible Issues.

How do I find my drain cleanout?

The cleanout is usually a 4-inch-diameter pipe with a screw cap that has a square knob or indentation on the top. It’s most likely going to be popping up from the ground outside your home between the foundation and the street. The cleanout might also be on the side of the home, closest to the bathroom.

How many lids are on a septic tank?

In order to make repairs or perform regular maintenance or cleaning/pumping of the tank, access must be provided. There are usually two lids located at the top of the septic tank-one located over the inlet “T” and one located over the outlet “T” (see “Septic Components: Septic Tanks”).

Where do you install cleanouts?

Cleanouts shall be installed at each change of direction greater than 45 degrees (0.79 rad) in the building sewer, building drain and horizontal waste or soil lines.

How to locate your septic tank and your drainfield

Septic systems on-site are used for accepting and treating wastewater in homes that are not linked to the municipal wastewater management system. A septic system is comprised of three components: a septic tank, a drain field, and piping. As a homeowner, it is your responsibility to properly operate and maintain your septic system in order to avoid system failure. For example, depending on the legislation in your area, you may be compelled to pump it on a regular basis. It is impossible to perform maintenance operations, however, if you do not know where the tank is located.

Steps to follow to locate your septic tank and drain field

The contractor that designed and constructed the septic tank on your property should have submitted an as-built diagram with the local health authority before starting work on the project. In the event that you have the contractor’s contact information, you can ask them for a schematic, which you can then use to pinpoint the location of your septic tank. If you do not have a copy of the schematic, you can request one from the local authorities. Depending on whether the installed system included electrical components, the schematic may be available at the regional building department offices.

If you are unable to locate the tank using this diagram, you will need to do more research on the land in order to determine its position.

• This pipe is commonly found in the basement of a home, and it is a 4″ black pipe with a cleanout at the bottom.
• Simply look for possible access coverings or a structure that might be concealing it.
• These pumps are used to remove waste from the building.
• It is supposed to be connected to the sewage output pipe.
• As soon as you’ve discovered the sewer outlet in your basement, you may use it to figure out where the sewer line departs your home through an outside wall.
• As a result, it is probable that the tank will be positioned around the corner from the building.

Tips for locating your septic tank

Septic tank lids should be visible from the outside. An underground riser may have been added, which will make it simple to find your septic tank in some instances.

However, it is conceivable that the septic tank cover is buried underground, which is especially true for older homes. Following are some pointers to assist you in locating the septic tank in this and other similar situations.

• It may be possible to discover the septic tank lid underneath using a metal detector if it is buried. Prevent wearing footwear that contains steel or any other metal in order to avoid interfering with the readings of the detector
• Instead, you can use a flushable transmitter that is flushed down the toilet and then tracked with a receiver. When it comes to septic tanks, the strongest signal will be seen close to the intake region of the tank.

Depending on whether the septic tank is above or below ground, you may have to dig to get to it. Construction materials for septic tanks include concrete, fiberglass, or plastic, and their shapes can range from oblong to cylindrical to rectangular. The majority of modern septic tanks will have their lids positioned in the center of the tank, and the lid should be within three feet of the ground surface in most cases. However, depending on a variety of conditions, such as farming and other human activities on the property, it is conceivable that it will be significantly deeper.

Additionally, you may use a small steel rod to probe the earth in order to pinpoint exactly where the tank is located as you continue digging.

Inspecting the tank

It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been identified. First and foremost, you may unscrew the lid to inspect the scum and sludge layer beneath it. In addition, the use of tracer dye tablets allows you to check the septic tank without having to dig it up. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of two days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field has a glowing green hue surrounding it.

It is possible that someone will fall into the tank, causing significant damage or possibly death.

Conclusion

You can identify your septic tank without assistance from a professional, but it is a good idea to have someone who is properly educated in septic tank maintenance examine and maintain your septic tank on your behalf. The effluent filter in your tank should be washed into the open septic tank rather than on the ground in your yard if your tank has one. It may also be a good idea to make a note of the position of the septic tank when it has been discovered. This will be beneficial to anyone else who may require access to the septic tank in the future.

Septic tanks release combustible and hazardous gases, and as a result, they must be located in an open area.

How to Find the Lid on a Septic System

All septic tanks eventually fill with sediments and must be pumped out on a regular basis in order to remain in excellent functioning order. If the tank’s lid is not on a riser at ground level and you are not the home’s original owner, you may be unable to determine where the lid is located.

A typical septic tank is 4 inches to 4 feet underground, with all of its components, including the cover, buried between 4 inches and 4 feet underneath. This is true regardless of whether the septic tank is equipped with special risers that keep the lid flush with the surface of the ground.

Consult A Map

First, choose with the most straightforward choice. The installation of septic tanks at all locations is recorded in most counties’ permission records, which are kept on file for future reference. Typically, this will include a schematic indicating the placement of the tank on the land, as well as certain dimensions that will allow you to measure to the precise site of the tank. If your tank was placed before your county made it a requirement to record the location of such tanks, you may find yourself with nothing to show for your efforts.

Search For A Sign

Septic tanks are placed in such a way that they are as unnoticeable as possible on the land. After the grass has grown back after installation and some time has passed, it is possible that just a few visual indications will remain. Pay particular attention to the contours of your yard for any inexplicable high or low points that might suggest the presence of an underground storage tank.

Follow The Pipe

Installation of the septic tank takes place along the sewage line that runs from the house into the front yard. Locate the 4-inch sewage pipe at the point where it exits the home in the basement or crawl space, if it is there. Locate the same spot outside and make a note of it. Insert a thin metal probe into the earth, identify the 4-inch sewage line, and follow it across the yard, probing every 2 feet, until you reach the end of the property. Septic tanks are required to be at least 5 feet apart from the home in all states except Alaska.

Whenever the probe makes contact with flat concrete, fiberglass, or polyethylene it indicates that the tank has been located.

Locate The Lid

The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Investigate the tank’s circumference to determine its boundaries and outline the rectangle’s boundary using a pencil. A septic tank that was built before 1975 will have a single concrete lid that is 24 inches in diameter in the center of the rectangle. If the tank was built after 1975, it will have two covers made of fiberglass or polyethylene, centered at the ends of the rectangle and centered at the ends of the rectangle.

Call A Professional

Opening a septic tank is a job best left to the pros once the lid has been discovered. Concrete septic tank lids are extremely heavy, and many require the use of lifting tools to remove them completely. An open tank has the potential to release toxic gases. Anyone going around on the property who comes into contact with an exposed septic tank might be in risk. Because of the noxious vapors present in an open tank, falling into one can be lethal.

Mark The Spot

Make a note on the ground near where the tank was pumped by a professional and the lid was buried to serve as a reference in the future.

In order to keep track of where you are, you should choose a hefty circular patio tile that is embedded in the ground. Additionally, draw your own map of the area and store it with your other important papers.

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.

Inspect Your Property

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.

• Purchase a soil probe that you may use to locate hidden sewage lines and septic tanks. Find the main sewage line that goes to your septic tank by going to your basement or crawl area. Look for a pipe with a diameter of around four inches that leads away from your home. Keep track of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors. The sewer lines will take you to the location of your septic tank. If you have a drain snake, you may use it to try to track the approximate course of your pipes. Every two feet, insert the tiny metal probe into the dirt to locate and trace the sewage lines. Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks as much as 10 to 25 feet away, you may have to probe a bit further out before striking the tank.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.

Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.

Don’t Try to Fix Septic Tank Issues Yourself

Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.

Schedule Septic Tank Maintenance

The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.

We are open seven days a week, twenty-four hours a day.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.

If you’re also using well water, it’s possible that you won’t receive one at all.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis. Preventing worse problems and the need for costly repairs down the line may be accomplished via proper septic system maintenance. All of the heavy lifting has been delegated to our team of professionals.

How To Find My Septic Tank

1. What is a septic tank
2. How do I know if I have a septic tank
3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

1. “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
2. When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
3. The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
4. In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

• A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
• A septic system is likely to be installed in your home if you reside in a rather rural location.
• Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
• When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
• Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

• If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
• The county health department is responsible for keeping track of septic systems.
• A septic tank’s position could be depicted on a survey map, for example.
• The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

1. In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
2. By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
3. The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
4. Going via the sewage line itself is another method of locating the septic tank utilizing it.
5. Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
6. When the snake comes to a complete halt, it has almost certainly reached the tank.
7. While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
8. When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

• Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
• Directly in front of the home Immediately adjacent to your well (if you have one)
• In close proximity to trees or densely planted regions
• In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job

How Much Does It Cost To Clean Out a Septic Tank? See Breakdown

When it comes time to have your septic tank cleaned out, there is one very crucial thing to consider.

“How much does it cost to pump a septic tank?”

The solution is not as straightforward as you may expect, but it is also not going to need the completion of a four-year degree to figure out.

In order to wipe away years of buildup from your laundry, toilet, shower, sink, and jacuzzi, there are a few things that influence the amount you may have to spend for the “Mega Flush.”

Let’s get started.

First and foremost, you should be aware that septic tanks are analogous to individuals. They are available in a variety of forms and sizes, and their ages range from recent to ancient. Their health problems are also quite diverse, as are their demeanors and dispositions. Some are fearful and prefer to remain concealed from view, buried beneath the surface of the earth. People are more forceful, use prominent risers, flashing lights, and even audible alarm systems to alert others to their commanding presence in the room.

1. The septic tank is still on the table, believe it or not.
2. Let alone those who behave more like the adolescent who ate too many burritos for lunch and then insisted on releasing his farts in the center of your kitchen while you were attempting to cook supper!
3. The clinical research “Various Personality Disorders Common to Septic Tanks” has been sponsored by Shankster Bros.
4. But it is a discussion for another day.

The costs pertaining to the cleaning of a septic tank can be divided, (or multiplied), into 4-5 categories:

1.) The size of the tank 2.) The tank’s accessibility. 3.) The property’s geographic location in respect to the service area 4.) The frequency with which cleaning is performed 5.) Calculate the volume of the quantity of gallons

Let’s break these costs down:

As previously said, septic tanks are available in a variety of designs and sizes. Some people are surprised to learn that the septic tank sizing requirements for homes are based on the number of bedrooms, that the requirements for churches are based on the seating capacity of the auditorium, that the requirements for factories are based on the number of employees, and that the requirements for campgrounds are based on the number of campsites.

Current septic tank sizing requirement guidelines in Indiana are as follows:

Home has 5 bedrooms and a 1500 gallon tank. 4 bedroom house with a tank of 1250 gallons. a three-bedroom house with a 1000 gallon tank 750 gallon tank for a two-bedroom house 500 gallon tank for a one-bedroom house It’s worth noting that any jetted bathtub, such as a hot tub or jacuzzi, with a capacity greater than 125 gallons qualifies as an additional bedroom. Always keep in mind that many of the systems being installed today are equipped with a secondary tank that serves as a pump station, pumping your sewage out to the leach field or sand mound, where it is distributed through piping and receives its final treatment before being leached away into the earth.

2.) Accessibility of tank

Unfortunately, some septic tanks have been constructed in difficult-to-access locations. Consider the possibilities: beneath the deck, beneath the garage floor, beneath the new living room that was constructed a few years ago, beneath that enormous pine tree that I planted 40 years ago, and so on. Yes, we have witnessed each and every one of those scenarios, as well as countless more. The presence or absence of a Riser in your tank is another factor that affects accessibility. This is a pipe that is attached to the lid of your septic tank and extends to the surface of the earth below the tank.

This may necessitate digging in order to expose the tank’s access lid, which may incur additional costs.

Some service providers will charge you an additional fee if they have to use more than one length of pipe to reach your storage tank. Fortunately for you, Shankster Bros. does not share this sentiment!

3.) Distance from the service area

According on the location of the client in relation to the service provider’s service area, many service providers charge on a sliding scale. Take, for example, Shankster Bros., which has its headquarters in Northern Indiana. A client in Kentucky will be charged more than a customer in Kosciusko, Whitley, Wabash, Fulton, Elkhart, or the adjacent counties if we get a call from that client.

4.) Frequency of cleaning

Some of our clients, particularly those who live near lakes, are employing tanks that solely hold septage rather than allowing it to be leached out into the environment. This necessitates the need to pump them out on a regular basis, perhaps as frequently as once each week. Because of the regularity with which the service is provided under these particular circumstances, we are able to provide lower costs.

5.) Volume the amount of gallons

Customers with enormous amounts of garbage to dispose of, such as campers, big business establishments, and even wastewater treatment plants, may be required to do so at certain times. In this situation, it will be necessary to mention special price once more. So, when you phone the office to inquire about price, be prepared to provide the following information so that the receptionist can provide you with an accurate quote as promptly as possible:

• The location of the property in need of cleaning services
• The size of the septic tank, if it is known
• And Whether your tank is equipped with an access riser or not.

Alternately, if you are already a customer, we already have all of that information on file with your name or address, and we can quickly look up your information on file with either Shankster Bros, Strombeck Brothers, North Webster Septic Tank Service, or Shepler septic tank cleaning, and provide you with an instant quote based on the information you have already provided us.

A general average cost to clean out a septic tank in Northern Indiana is as follows, although you can see specific pricing varies according to the parameters I have outlined above:

Cleaning a 1000 gallon tank will cost between $200 and $300.00. Over 1000 gallons, per gallon, there is a 7 cent per gallon charge. Fee for digging – $75.00 per hour Line cleaning costs between $225 and $300.00. Riser for retrofitting – $190.00 Whenever you want aseptic tank cleaning, pumping, or inspection, please do not hesitate to contact Shankster Bros. at any time of day or night.

FAQs — JT’s SEPTIC

Make sure to contact JT’s Septic as soon as possible! It is possible for us to assist you in diagnosing the problem and determining if it is a plumbing issue or a problem directly connected to your septic system. Wastewater backing up into more than one household fixture (even during dry weather), pooling water or muddy soil around your septic system or in your basement are all signs that your system needs to be checked. If you notice any of the following, contact us to have it checked: a strong odor around the septic tank and/or drainfield

Should I Use Septic Tank Additives?

According to current research, there is no clear proof that these items can prevent septic system failure or that they will improve system function. The addition of compounds to a septic tank will not eliminate the necessity for routine tank cleaning. Septic tank cleansers, rejuvenators, and primers that are promoted as such will not hurt your system, but they will not benefit it either. However, there is already a large amount of bacteria in the tank that will break down waste products, so using enzymes or yeast would not hurt your system at all.

Septic system additives should be avoided, according to the North Dakota State University Agriculture Communication. “Do Septic System Additives Work?” you might wonder. -Tank Refueling Station

what are the PVC pipes sticking up in my yard?

According to current information, there is no clear proof that these items will prevent septic system failure or that they would enhance system function. The addition of compounds to a septic tank will not eliminate the requirement for routine tank cleanings. Septic tank cleansers, rejuvenators, and primers that are promoted as such will not hurt your system, but they will also not benefit it. However, there is already a large amount of bacteria in the tank that will break down waste materials, thus using enzymes and yeasts will not hurt your system.

The North Dakota State University Agriculture Communication recommends that you avoid using Septic System Additives.” Is it True That Septic System Additives Are Effective?

will household cleaning products harm my system?

The majority of specialists believe that the usual use of household cleaning solutions will not harm the system since it will not prevent the activity of bacteria in the tank from taking place as intended. A large amount of some chemicals, on the other hand, may interfere with the breakdown of wastes in the tank or cause the soil treatment area to get clogged. Please remember that the goods you use may ultimately make their way into the groundwater systems in your community.

How Often Should I Pump My Septic Tank?

Most tanks require pumping every 3-5 years, depending on the size of the tank, the amount of wastewater that flows into the tank on a daily basis, and whether or not the tank is equipped with a trash disposal. The state of Arizona currently does not have any laws requiring maintenance and inspection (with the exception of those pertaining to the sale of a home), but the Environmental Protection Agency and local health departments strongly recommend routine maintenance to help prevent groundwater contamination due to nitrogen, phosphorus, and disease-causing bacteria that can be found in wastewater.

I just had my tank pumped and it already looks full!?!

There is a distinction between being full and being overfull! An empty septic tank will fill up as quickly as you use up the quantity of gallons it can contain in terms of water use. The tank is meant to keep a liquid level to the bottom of the output pipe (that discharges into the disposal region) (that exits into the disposal area). When you look down into your tank, it should appear to be completely filled. It is necessary to hire an expert to assess the quantity of scum and sludge in your tank in order to decide when it is time to pump it out.

Does anyone have to be home to have jt’s pump my septic tank?

We usually advise people to have someone at their house for our service, but it is not mandatory. Our service technicians are quick and fast when it comes to finding and pumping out a problem. We enjoy having a homeowner and/or a Realtor on site for our inspections so that they may discuss any concerns that we may discover. If we happen to miss you during our service, we are more than pleased to accept a credit card payment over the phone.

Does JT’s Septic do leach line work?

At this time, JT’s does not install or do any work on leach lines or disposal locations.

We do minor repairs on septic tanks, as well as on the inlet and outlet sewer lines. Not sure if we can assist you? Just give us a call!

Why can’t you pump my septic tank out of the sewer cleanouts?

We have found that a tank cannot be efficiently pumped through sewage cleanouts because the pumps on our trucks are just too powerful, and there is no way to get all of the scum and debris out of the tank through a cleanout. It is advised that the tank access lids be used in order to remove all liquid and particles from the tank and to examine the baffles. To empty the tank completely, we unlock all compartments and use a pump to remove the full contents of it. The fact that you do not pump via the primary access holes in the tank itself is a disservice to yourself and your system.

how do you know the size of my tank?

Our experts and inspectors can identify the size of the tank based on the form of the tank; tanks for a normal residence are generally 1,000 or 1,250 gallons in capacity, respectively (tanks may be smaller or larger depending on bedroom count, style of tank, etc). Our trucks are outfitted with clear sight glasses, allowing our specialists to keep track of the number of gallons they are extracting from your tank. Our specialists are also trained to measure the tank measurements on the job site in order to establish the approximate gallon capacity.

why do you recommend routine maintenance and frequent pump outs when I’ve not a had a problem in the last 10 years and I’ve never had my tank pumped?

Even while many homeowners are able to go several years over the suggested maintenance time without experiencing any problems, harm is gradually being done. Solids that are insoluble in water and cannot be broken down by natural microbes are stored in the tank. This builds up over time until the tank no longer has enough space to hold everything. As a result, the solids make their way to the drain field where they fill up the pores in the earth, causing poor drainage and, eventually, the failure of the septic system and drainfield.

How long will my septic system last?

All septic systems have a defined life span, which means they will ultimately cease to function. The length of time a system will survive is determined by the system’s size, installation, soil composition, the water table, neighboring trees and roots, the amount of usage and abuse, and, most crucially, the frequency with which it is maintained and pumped.

if I have a garbage disposal Can i use it?

Yes! It is OK to use the garbage disposal for a limited amount of time, such as for food crumbs that remain after doing the dishes. Pump outs will be more frequent if the disposal is used more frequently, which will result in higher costs. The usage of a trash disposal can have a negative impact on your septic system by increasing the quantity of suspended particles that enter the system. Soil treatment areas can get clogged with suspended particles, which reduces the soil’s ability to remove waste.

CAN I FLUSH WET WIPESFEMININE HYGIENE PRODUCTS?

No! The presence of this problem is one of the most prevalent we see in tanks. Wipes and/or feminine hygiene items block sewer pipes and do not decompose properly in the holding tank, causing backups.

how often can i do laundry?

It is critical not to overburden your computer system.

Instead of completing a large number of loads in a single day, try to spread them out over the course of a week. Doing no more than two loads of laundry every day – one in the morning and one in the evening – is advised.

Can I have a water softener system with a septic system?

It is unlikely that a water softener will cause damage to most septic systems, albeit they may necessitate the installation of a somewhat bigger tank disposal area.

Can We Drive Over Our Leach Field?

Neither driving on the leach field nor on the entrance and exit sewer pipes, nor on the septic tank, is suggested by the manufacturer. It is possible to restrict or slow down efficient evaporation by compacting the soil over the leach lines. Evaporation is a critical component of the drainage and disposal process. It is possible to induce settling and even rupture of sewage pipes by driving over them. It is possible to produce cracks in a tank by driving over it, especially if it is made of fiberglass or plastic.

do i have a septic systeM?

Do you utilize well water in your home? Is there no meter on the water main that leads into your home? Do your water bill or property tax bill display a “$0.00 Sewer Amount Charged” or “$0.00 Sewer Amount Charged”? What about your next-door neighbors? Do they have a septic system? Your home may have a septic system if any of the following questions were answered affirmatively:

How do I find my septic system?

Once you’ve confirmed that you have a septic system, you may identify it by looking at your home’s “as built” drawing, inspecting your yard for lids and manhole covers, or calling us for assistance.

How Far Does The Tank Have To Be Away From The House?

The normal setback distance from the home is 10 feet. Yavapai County is committed to upholding this obligation. Keep these setbacks as they are to allow for easier access and to avoid any potential foundation and moisture concerns.

An alarm is going off in my tank- what do I do?!

The sirens on certain alternative systems alert the homeowner to a possible problem prior to effluent or waste backing up into the house. The alarm may sound to warn a problem with the electrical system or a high quantity of liquid in the tank. A pump or float may be malfunctioning, in which case it is recommended to contact either JT’s or your alternate system maintenance provider for assistance as soon as possible.

Can I Plant A Tree Over My Leach Field?

No. Root invasion from trees is one of the most prevalent problems that affect septic systems today. Certain species of trees are extremely harmful to your septic system and should be avoided at all costs. Please check your local nursery for further information.

does jt’s provide portable storage tanks?

We’re sorry, but we don’t provide portable storage tanks at the present moment.

can jt’s facilitate a pipeline repair?

We’re sorry, but we don’t provide portable storage tanks at the current moment.

why do you suggest running a sewer camera down my line?

A difficult blockage may necessitate the services of more than one plumber. Pipe obstructions can be caused by a variety of factors, including tree roots, grease, aging pipes, and foreign items. Our power snakes and Ridgid sewer cameras are excellent tools for identifying problems such as the following: Pipes that are broken, cracked, corroded, or collapsed are considered damaged and must be repaired or replaced. A clog is caused by a deposit of grease or a foreign item that prevents the passage of water.

Joints that are leaking—the seals between pipes have failed, enabling liquid to leak through. Root invasion occurs when tree or shrub roots penetrate the sewage system, limiting normal flow and/or causing a clog in the pipe.* The following is the source:

COMMON PROBLEMS — JT’s SEPTIC

You should examine the sewer cleanout on the exterior of the home if you are hearing gurgling and all of the house fixtures are clogged. This is often a black 3-4 in color “inch ABS pipe with a threaded cap is available. Remove the cap (WARNING: BE CAREFUL! (WARNING: IT MAY CONTAIN SOME PRESSURE!) : Assuming the sewage line is completely dry, you will have a clog inside the home plumbing, directly in front of the cleanout valve. Make a phone call to a plumber and have them rooter the line. Sewer line cameras are available from several rooter/plumbing businesses.

• You have two options at this point: call your preferred septic provider or pull up the tank lids yourself and check the water level and solids content in the tank yourself.
• Most tanks erected after January 2001 include a filter that has to be cleaned at least once a year (we clean filters—please call us).
• We’ll even notify you once a year when it’s time to clean your filters!).
• It’s likely that you have a blockage in your sewage system.

GURGLES

Whenever you flush the toilet, the water gurgles, the toilet takes an unusually long time to flush, or the water in the shower turns brownish after you have done the laundry, you are receiving a subtle indication that trouble is brewing. In order to determine when the tank was last pumped, look through your records and then contact your preferred septic provider for assistance.

ODORS

If you are experiencing unpleasant odors within your home, such as rotten eggs, it is likely that a trap or vent inside your home is not venting correctly. Call your plumber right away since these gases are harmful to both people and animals!

ODORS OUTSIDE IN THE YARD

At times, the smells emanating from the roof vents will seep into the yard due to meteorological conditions. Make use of a plumber to elevate the roof vents and/or to place a charcoal filter in the vents, as needed. It’s important to remember that your septic tank is vented via the roof.

SURFACING IN THE YARD

If you notice effluent appearing in your yard, contact your septic service provider immediately. If you see this, it indicates that your leach line has failed and you should get help right away.

HEAVY SOLIDS- OVERDUE FOR PUMPING

Contrary to common perception, you DO need to have your septic tank pumped on a regular basis. Pumping maintenance should be performed on a regular basis, otherwise your system will get overwhelmed with solid waste and eventually cause damage to your leach lines.

DON’T MAKE THIS HAPPEN TO YOU! This is an extreme example of a tank that is overflowing. There is sewage flowing from the tank access holes and into the yard!

grease build up in sewer pipes

Fats and grease should never be flushed down the toilet or sink. They have the potential to harden the lines and cause failure; they have the potential to generate an excessive buildup of the floating scum layer in the septic tank; and they have the potential to go into the disposal regions and adjacent soils and completely block the system off. A shattered lid can pose a serious threat to both animals and children. It is conceivable that they will fall through the cracked or broken lids and will not be noticed until it is too late to save themselves.

crushed or settled pipe

This is the second most prevalent problem we notice in septic systems that are less than 10 years old. In addition to blocking flow, loose fill soil surrounding the tank is causing a backup into the house since it is pulling the pipe with it as it settles. We have even observed instances when contractors installing new systems do not correctly pack the fill earth below the pipe, resulting in pipe settlement on systems that have not been utilized or have only been used for a short length of time (see below for an example).

SEWER OUTLET PROGRESSION

When it comes to modern septic systems, this is the most typical issue we encounter. Take note of the fact that the unsupported outlet pipe is being driven down by settling dirt. Watch as the water level in the tank rises, forcing the flow of water in the inflow sewage line to slow. This will eventually result in a clog in the inflow sewer line at some point. The solids flowing down from the house will not be able to enter the tank correctly because of the high water level.

examples of settled sewer pipes:

INSTALLATION OF A TANK AND/OR REPAIR OF SEWER PIPESTHE “POLY” PIPEIMAGES BELOW PROVIDE AN EXAMPLE OF WHAT PIPENOTTO USES WHEN INSTALLING A TANK AND/OR REPAIR OF SEWER PIPES However, despite the fact that this grade of sewer pipe is less expensive at the time of purchase, it might end up costing you a lot of money in the long run!

settled inlet sewer pipe on unused system:

Even if the septic system has not been utilized in some time, it is conceivable that problems will be discovered during the inspection process. Pipes might settle on unoccupied ground and in yards as a result of faulty installation and/or automobiles and/or ATVs running over the pipes without realizing they are there. It may be beneficial to all parties to have a skilled inspector take a look at the system and diagnose any concerns, even though the County does not require an examination on an underused system before transferring ownership.

Roots growing in and around the septic tank:

In addition to disrupting the system by clogging or destroying drainage and distribution lines, tree roots can also enter the tank, causing it to leak. Foul odors, poor drainage, and patches of vegetation in the leach field are just a few of the signs that you may have a root problem.

ERODED BAFFLES

Solids are kept in the septic tank and away from the disposal area with the use of concrete baffles. Using baffles to reduce agitation of wastewater entering the septic tank and prevent particles from escaping the tank and entering the drainfield, baffles can assist avoid drainfield damage and extend the life of the drainfield.

If the baffles are broken, missing, or have never been placed, the drainfield’s life expectancy will be reduced significantly. Baffle repair normally entails the placement of a plastic tee at the end of the sewer pipes to prevent them from clogging.

orangeburg sewer pipes

Orangeburg pipe was made in Orangeburg, New York, from 1860 to 1970, and was utilized to plumb numerous septic and wastewater systems throughout Yavapai County during that time period. Orangeburg pipe is produced from rolled tar paper (wood pulp that has been sealed with hot pitch) and was considered a low-cost alternative to metal, particularly after World War II, because of its flexibility and durability. In fact, the pipe itself is so soft that professionals might cut it with a knife during the installation process!

Orangeburg, on the other hand, is known for degrading over time (it has a 50-year lifespan at the most) and deforming when subjected to pressure.

If the septic system is approved, Orangeburg will normally be stated on the permits as the material for the inlet and/or outflow pipe material, respectively.