What Does A Septic Tank Riser Do? (Correct answer)

A septic tank riser is a pipe made of either plastic, fiberglass, or concrete. It creates a vertical portal at the ground surface for easy access to the septic tank for inspection and pumping out. The lid is then either left exposed or with a very thin layer of soil and grass over it.

slideshare.net

• The main purpose and benefit of a riser is to raise the height of the septic tank lid. In most cases lids are locked onto the top of a septic tank, and are held down by stainless steel screws. Some risers may also include structural ribs.

Should septic tank riser be above ground?

Landscaping Around Septic Tank Risers However, septic tank risers should never be buried. Instead, they should be 2 inches above final grade to prevent groundwater from entering the system.

Are septic tank risers safe?

Fortunately, lids and risers in today’s onsite market can help prevent these unfortunate incidents. These innovative products ensure septic tank covers are secure and prohibit unauthorized tank access.

How many septic tank risers do I need?

A single riser is required for accessing the pump chamber for this type of system. If you don’t have two additional risers, you should locate your septic tank and install risers for both the inlet and outlet openings, as described above.

How high should septic tank riser be?

Tank risers are typically installed about 3 inches above grade. Having the lid above grade will make it easy to find, however, some people will choose to have the lid just a couple of inches below grade so that is easier to mow over and less visible.

How much weight can a septic tank riser lid hold?

The 24-inch solid fiberglass DuraFiber riser lid from Orenco Systems has a flat-style lip for PVC and HDPE pipe. It weighs 10 pounds, but resists damage from lawn equipment and can withstand a 20,000-pound load.

How do you hide a septic tank riser?

The easiest way to hide your septic riser is by simply placing something over it, such as a hollow, lightweight landscape rock, a birdbath, a sundial or a decorative lawn ornament. Apply basic landscaping principles when deciding what to use.

Is a septic riser necessary?

Installing septic tank risers are a highly recommended addition to your septic system. The septic tank riser will make maintaining and monitoring your septic system much easier and more convenient.

Can you cover septic tank lids?

If you have a traditional septic system, the tank should be pumped every 3-5 years. That means that the septic lids should be accessible every 3-5 years. You can use almost any temporary, movable objects to cover your lids, like: Mulch (but not landscaping)

How many lids are on a septic tank?

In order to make repairs or perform regular maintenance or cleaning/pumping of the tank, access must be provided. There are usually two lids located at the top of the septic tank-one located over the inlet “T” and one located over the outlet “T” (see “Septic Components: Septic Tanks”).

Do they make square risers for septic tanks?

The Polylok square riser adapter ring is designed to connect the Polylok septic tank risers or lids to an existing concrete tank with large square or round openings.

What are access risers?

Fiberglass Access Risers (RF) Orenco^® Fiberglass Access Risers are designed to provide access to septic tank openings, as well as watertight connections between the tank, riser, and lid. They can be cast into the tops of concrete tanks or bonded to a fiberglass tank. They can also be used as valve enclosures.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

What Is a Septic Tank Riser?

If you have an older septic system, you may be wondering what a septic tank riser is and why you would need one. Traditional systems were designed to be out of sight, out of mind; they were buried for 15-20 years with no consideration given until they required emergency pumping or repair. Newer septic systems now have risers, which are a positive thing, since they provide a more efficient way of draining the tank. Septic tank risers provide simple access to your septic tank from the ground level as well as increased view into the operation of your septic system.

The Benefits of a Septic Tank Riser

Before we go into the advantages, it’s important to understand what a septic tank riser is. Riser are often built of plastic or concrete, depending on the use. They are enormous circular pipes that are installed above the cleanout entrance of the septic tank and are long enough to extend the cleanout opening all the way to the ground level. The advantages are as follows:

• Even when the ground is frozen, it is possible to get access during the winter months. Maintenance and pumping of the septic system may be done quickly and easily. Septic system repair should not need digging up your yard. A visual reminder of the importance of your septic system

The last advantage may appear to be somewhat counter-intuitive. What are the benefits of having a visual reminder of your septic system? Preventing premature septic system collapse is possible through periodic septic system maintenance. With a septic tank riser, you’ll not only be able to identify the position of your septic system, but you’ll also have a visual reminder to have your system pumped at least once every two to three years as well. However, the septic tank risers that we install are intended to fit in with the surrounding environment.

How Much a Septic Tank Riser Costs

In your house, your septic system is one of the most vital mechanical systems to have working properly. A septic tank riser, which costs only a one-time installation price, can safeguard your septic system for many years to come. The ease with which maintenance and pumping may be performed will almost instantly result in a return on your investment. You may also say goodbye to costly and unsightly excavations when it comes to upkeep. Although the ground may be frozen in winter, you will be able to inspect your septic system visually even during the coldest months of the year.

This will result in costly emergency repairs.

If you would like to learn more about how septic tank risers might assist you, please contact us at 800-595-7907.

Traditional systems were designed to be out of sight, out of mind; they were buried for 15-20 years with no consideration given until they required emergency pumping or repair.

Newer septic systems now have risers, which are a positive thing, since they provide a more efficient way of draining the tank. Septic tank risers provide simple access to your septic tank from the ground level as well as increased view into the operation of your septic system.

What are the benefits of a septic tank riser?

Before we go into the advantages, it’s important to understand what a septic tank riser is. Riser are often built of plastic or concrete, depending on the use. They are enormous circular pipes that are installed above the cleanout entrance of the septic tank and are long enough to extend the cleanout opening all the way to the ground level. The advantages are as follows:

• Even when the ground is frozen, it is possible to get access during the winter months. Maintenance and pumping of the septic system may be done quickly and easily. Septic system repair should not need digging up your yard. Your septic system will be visible as a reminder

The last advantage may appear to be a bit counter-intuitive. What are the benefits of having a visual reminder of your septic system? Preventing premature septic system collapse is possible through periodic septic system maintenance. With a septic tank riser, you’ll not only be able to identify the position of your septic system, but you’ll also have a visual reminder to have your system pumped at least once every two to three years as well. However, the septic tank risers that we install are intended to fit in with the surrounding environment.

How much does a septic tank riser cost?

In your house, your septic system is one of the most vital mechanical systems to have working properly. A septic tank riser, which costs only a one-time installation price, can safeguard your septic system for many years to come. The ease with which maintenance and pumping may be performed will almost instantly result in a return on your investment. You may also say goodbye to costly and unsightly excavations when it comes to upkeep. Although the ground may be frozen in winter, you will be able to inspect your septic system visually even during the coldest months of the year.

In addition to protecting your system and saving you money, a septic tank riser is a reasonably easy solution.

We’d be happy to tell you more about how septic tank risers might help you.

for an appointment or to learn more about our services.

Felix Septic Service is a company that provides septic service. 2020-05-19T15:44:01-04:00

What You Should Know About Septic Tank Risers

Septic tank risers are an important part of any septic system, and they should be installed in every property. This article will provide you an overview of septic tank risers and how they may help your septic system. What Is the Function of a Septic Tank Riser? A septic tank riser is a conduit that connects your home’s surface drainage system to your septic tank beneath the ground level. An access port or the pump-out ports on the septic tank are where the riser connects to the tank. Septic tank risers are equipped with lids that can be quickly removed to allow you to check or pump your septic tank without having to dig up your yard.

• These structures are often made of materials that disintegrate slowly over time, such as plastic or concrete.
• What Are the Advantages of Using Risers?
• Normally, this entails digging up your yard before the pump is installed and reburying the tank once it has been installed.
• The use of a septic tank riser can help to minimize the amount of time spent pumping your septic tank.
• The fact that the riser is visible above the surface of your yard makes it an ideal signal for locating your septic tank the first time you need to discover one in your yard.
• For those who want to stay in their house for several years, septic tank risers are not only handy, but they are also cost-effective.
• Concrete risers are more durable, but they are also more expensive, and the price will be determined by the quote you receive from the contractor who will be installing them.

Because labor expenses account for a large amount of the fees that contractors charge for septic system inspection and pumping, installing a riser may possibly reduce the future cost of septic service by as much as 50 percent.

Each and every property can profit from the installation of a septic tank riser, but this does not imply that you should do so immediately.

This allows for the installation of the pump and riser to be completed in a single step.

Because a riser should be considered a long-term investment, you should be certain that your tank is in good functioning shape before installing one.

A septic tank riser is a straightforward concept that may save you a significant amount of money and pain when it comes to septic system maintenance and repair.

We look forward to hearing from you and addressing any concerns you may have concerning your septic system requirements. Contact us now. Please let us know how we may be of assistance to you and your septic system right now!

undefined

The inefficiency of having to dig up your grass to access your septic tank whenever it has to be pumped or undergoes periodic maintenance is well known to those who own septic systems. However, while burying the tank below is a practical approach to keep it secure and hidden, it can make routine duties more complex, costly, and time-consuming. This is one of the primary reasons why many individuals prefer to install a septic tank riser. As the name implies, it is a concrete or plastic pipe that runs from the pump-out hole to the ground level of a sewage system.

If you’re deciding whether or not to acquire a tank riser, consider the following advantages and disadvantages:

• A septic tank riser makes it simple to determine where the system is located. PRO – Low maintenance: Besides being useful for maintenance, it may also be useful for monitoring the system’s operation and quickly accessing the system if something goes wrong. BEING ABLE TO FIND THE Septic System FAST may save you valuable time and work. Additionally, it may be able to assist minimize the expenses of any future service visits
• Nevertheless, PRO – Protected from the elements: Septic tank risers are intended to endure everything Mother Nature throws at them, including snow, wind, and whatever else Mother Nature has in store for them. Depending on the material used, the riser can be formed of concrete or a thick heavy plastic that is fitted with a highly strong cover to keep the system totally free of dirt. This can help to decrease damage to the system and avoid the occurrence of additional problems. A pipe or lid in the center of a lawn may be considered an eyesore by some homeowners, regardless of how handy it may be in other ways. CON – Convenience: In order to allow the grass to grow over the top of the riser lid, one alternative is to set the lid a couple of inches below the level of the lawn. Afterwards, all you’ll have to do is dig up that location without disrupting the rest of the yard. In most cases, homeowners prefer to build a riser on an existing septic system rather than constructing a new one. This is a project that will require the services of a septic tank professional. Even while this will necessitate some digging and disturbance in the yard, it’s vital to remember that it will ultimately preserve your lawn. CON – Cost:There are certain costs connected with building a septic tank riser, notably the cost of the supplies and the labor involved. Although this is an expenditure that will pay for itself in the long term through years of cost savings during future inspections and maintenance, it is one that should be considered.

It’s evident that building a septic tank riser may be a desirable upgrade, despite the few small drawbacks that may be connected with the process. If you have any more questions, please don’t hesitate to contact the professionals at Mike’s SepticMcKinley Sewer Services. Throughout Prior Lake, MN, we are experts in everything septic. This includes tank and system design as well as installation, accessories, pumping, cleaning, and routine septic maintenance. Reach out to one of our septic system specialists immediately by phone or email!

Benefits of Installing Septic Tank Risers

Many people consider their septic system to be a “out of sight, out of mind” service that they don’t think about until there’s an issue. Due to the fact that septic tanks are underground, it might be difficult to discover the access ports if you aren’t familiar with the area where your tank and its components are placed. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings. Continue reading to learn more about septic tank riser installation in the Twin Tiers region, or contact us to arrange service now.

• It is a large-diameter concrete or plastic pipe that runs vertically from the pump-out apertures or access ports on top of a sewage treatment system down to ground level.
• With a lid that fits firmly on top of the riser and lies flush with the ground, digging and searching are no longer necessary.
• Installation Every week, our staff completes the installation of risers.
• When feasible, we’ll pick a riser that will stretch all the way to the surface of your grass, or we’ll trim one to fit.

To make the lid merge perfectly into your yard or landscape, you are welcome to put grass or mulch around the top. Benefits When it comes to septic tank risers, there are a range of advantages to consider.

1. The cost of installing a riser is a one-time expense. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times
2. There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. Furthermore, it saves you money by avoiding the mess that it might create in your yard. We understand that time is money, and when our staff has simpler access to your septic tank, we can get your project done or your problem resolved more quickly. It’s critical to be aware of where things are at all times. Are you thinking of building a new patio, home extension, or backyard project? The ability to pinpoint the location of your tank and its components is quite beneficial. We’ll even draw you a schematic if you need one
3. Just let us know.

Are you ready to speak with us about septic risers? When it comes to septic tank repair, this is a straightforward service that will make your life a whole lot simpler. To schedule service, please call us at: 607-564-7931.

5 Reasons to Install Septic Tank Risers

Most homeowners consider their septic system to be a “out of sight, out of mind” service that receives little or no attention unless there is a problem. Septic systems are buried underground, and if you aren’t sure where your tank and its components are, it might be tough to discover your access ports or manhole covers if you aren’t familiar with your property’s layout. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings.

• What is a septic tank riser and how does it work?
• Risers, sometimes known as “extensions,” are available in a variety of heights to raise any access port up to grade.
• Because the riser extends from your tank entrance to the lawn surface, it makes it much easier to reach your septic tank for pumping, maintenance, and inspections than it would otherwise be.
• Digging down to your septic tank lid or access port and fitting the riser to the entrance are the steps involved in installation.
• Then we’ll fill the area around the pipe with earth and put the lid on top of it once it’s in place.
• The AdvantagesWhen it comes to septic tank risers, there are a plethora of advantages to consider.

1. The expense of installing a riser is one-time, but the advantages are long-lasting. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times
2. There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. This is in addition to the mess that it can create in your yard if the lid is buried several feet down
3. Nonetheless, it saves you money. Time is money, after all! Furthermore, since it is simpler to reach your septic tank, our staff can complete your task or resolve your problem much more quickly
4. It is critical to understand where everything is located. If you’re putting up a new patio, house addition, or backyard project, understanding where your tank and its components are located will be quite beneficial to your project. We’ll even draw you a schematic if you need one
5. Just let us know.

It is only necessary to install a riser once, yet the benefits will last for years to come. Once the extension is completed, you will not be required to pay for it again, and your tank will be easily accessible for pumping, maintenance, and inspections. Forget about looking for your access ports anymore. No more digging! When we bring your manhole cover up to code, it will be clearly visible at all times. This is especially useful during the winter months, when digging up a buried manhole cover can take several hours and need a lot of patience.

Timing is everything!

It’s quite helpful to know the exact location of your tank and its components if you’re planning a new patio, house addition, or backyard renovation. Even if you don’t want a diagram, we’ll make one for you;

Septic Tank Risers

In what capacity does an aseptic tank riser serve, and why would you require one? If your septic tank service worker has to dig up your yard every time your septic tank has to be cleaned, you do not have a riser built, and it is probable that you have a concrete cover buried someplace underground. The Ariser septic tank lid replaces your old septic tank lid, allowing you to access your tank from aboveground, making it easier to manage. It is possible that installing a riser will lower the cost of pumping your tank (this is not a guarantee; be sure to inquire).

It may even be possible to gain access to your septic main for cleaning and inspection depending on your external pipe system.

However, if you have an older system, the majority of tanks were built with concrete lids that frequently degrade and are typically buried beneath the earth.

Most septic pumping companies also provide riser installation, and it is typically less expensive to consolidate services rather than buy them separately because you save on service fees by doing so.

Septic Tank Riser Styles

Septic tank risers are available in a variety of designs and are composed of a variety of various materials, including concrete. Despite the fact that some are built of concrete (which are the most durable), some people find them ugly. Concrete risers are more difficult to construct and may need the use of special equipment to lift them off trucks, increasing the labor costs even if the materials are less expensive. Septic covers made of polyethylene, PVC, and other plastic materials are lower in weight and come in a variety of heights to meet your demands.

The majority of designs may be made to fit your specific height requirements.

It should be noted that the load-bearing capacities of the lids varies.

Riser pipes are available in a variety of sizes ranging from 8 to 24 inches in diameter, with lengths varying based on the depth of your tank entrance.

Although it is possible to cover them with sod and mark their location in order to be able to raise them for maintenance, this defeats the point of accessibility and may lose you of the potential savings that come from not having to dig out your cover every time it has to be serviced.

Septic Tank Riser Cost

Depending on the size, the material, the design, and the installation, the cost of a septic tank riser can vary significantly. Spend at least $150 on a basic model, but keep in mind that they may cost up to $400 depending on the model you select. If you have a twin septic tank, double the above figure by two. The labor and supplies are one-time expenses that will be soon recouped by not having to pay for digging when you want pumping or inspections of your system. Most of the time, they can be installed in a half-hour or less.

What is a Septic Tank Riser?

• A septic tank riser is normally priced between $200 and $400, not including installation. Risers reduce labor expenses by saving septic contractors time
• Therefore, they lower overall expenditures. The installation of a septic tank riser is not a do-it-yourself activity. Septic tank risers are available in both concrete and plastic construction.

Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. If you’re a homeowner in the United States who relies on a septic tank, you’re probably aware that they’re buried deep in the earth and can be difficult to detect and access when it comes time to do maintenance on them. As a result, you may be required to pay substantial digging and labor fees. With a septic tank riser, you can now find and manage your septic system more rapidly, which will allow you to put more money back in your pocket as a result.

What Is a Septic Tank Riser?

As the name implies, it is a long, robust pipe made of plastic or concrete that connects your septic tank, which is located deep below, with the surface of your lawn. The riser is connected to the septic tank by an access port or a pumping aperture in the tank’s wall. For inspection, maintenance, and pumping, risers have lids that can be opened without digging up your yard. This avoids the need to dig up your yard.

The Benefits: How Septic Risers Save You Money

As a rule of thumb, septic system manufacturers recommend that you examine your septic tank once a year and pump your septic tank every three to five years. However, if your septic system is not equipped with a riser, you may be forced to pay additional fees.

No Digging Fees

You or your septic tank specialist will have to spend time and money digging through the earth to locate your tank if you or he does not know the precise position of your tank. Your septic tank will need to be recovered with earth once it has been serviced and pumped without a riser, and they will need to do this every time they service your septic tank going forward.

Reduces Labor Costs

Incorporating an easily visible septic tank riser makes it easier for the contractor to access the riser lid, insert the pump hose, and start to work more quickly and efficiently. In this case, they may leave their heavy equipment at home, which saves you from having to spend a large amount of money in labor.

You’ll Only Pay for Materials and Labor Once

When you have a septic tank riser installed, you will only be responsible for the labor and materials used in the installation. The money you save on yearly inspections and regular local maintenance will more than compensate for the cost of the septic tank riser over time.

Septic Tank Riser Styles

Image courtesy of Ekaterina / Adobe Stock Septic tank risers are available in a variety of concrete and plastic types ranging in size from eight to 24 inches.

Each style has its own set of pros and disadvantages.

Concrete Septic Tank Risers

Concrete septic tank risers are more durable than other materials, but they have certain drawbacks of their own. Pros:

• Depending on how well it is maintained and drained, it can endure for 40 years. Septic tank risers made of steel are more durable than those made of plastic. Maintenance is less involved than with plastic

• Installing it is difficult, and purchasing it is expensive. Over time, it becomes more susceptible to corrosion and cracking. Increased labor expenses due to the need to lift and maneuver during installation or inspection

Plastic Septic Tank Risers

Plastic septic tank risers are available in a variety of materials, including PVC and polyethylene, among others. Pros:

• Purchase and installation costs are less expensive than those of concrete. Transport does not necessitate the use of large equipment. When compared to concrete septic tank risers, they are lighter in weight
• They may be covered with sod to improve their looks
• It is not susceptible to cracking like cement. Plastic is resistant to erosion.

• It is possible to crush it beneath the earth
• However, it is not as durable as concrete. Maintenance is more difficult to keep up with than with plastic.

How Much a Septic Tank Riser Costs

Installing a septic tank riser will cost between $200 and $400. Double septic tank risers will cost you twice as much as a single riser. It is more expensive to build concrete risers than it is to install plastic risers because of the weight of the concrete risers and the equipment necessary for installation.

Installation Usually Requires a Plumber

In part due to the difficulty of septic tank installation, it is not recommended as a Do It Yourself job. While it is possible to purchase all of the supplies for a DIY installation on the internet, there are several safety dangers associated with doing so. Opening a septic tank access can result in the emission of poisonous fumes, which can cause someone to go unconscious. Additionally, without prior experience, waterproofing and ensuring that the risers are properly connected together might be difficult.

They’ll dig up the area surrounding the access hole, then fill up the dirt around the pipe and install a cap on the upper section of the riser to make it easier to get to the pipe in the future.

Septic Tanks Risers- Bring Your Access To Ground Level

Getting a little tired of having to dig up your yard every time your septic tank has to be pumped out or serviced? Are you getting tired of dealing with incredibly hefty concrete lids? It appears that you are in need of septic tank risers in order to bring your access down to ground level! Our septic tank risers and covers are constructed of high-quality, heavy-duty polyethylene plastic, which makes them extremely sturdy and durable while also being lightweight and simple to handle.

THE POLYLOK ADVANTAGE

Septic tank risers are available in a variety of shapes, sizes, and designs on the current market. We believe our Polylok septic tank risers are the best money can buy in terms of quality. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

Once the hole has been backfilled, the structural ribs in the Polylok septic tank risers are inserted inside around each riser piece, providing them with tremendous strength and allowing them to maintain their shape under the pressure of the earth being pressed on them. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

Because the Polylok products are fully smooth on the outside, they will not cause any problems in frosty environments!

LIDS WITH HANDLES

The access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise maintained. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE ADAPTER RING

An adapter ring is required in order to properly install septic tank risers on your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

GET OUT YOUR MEASURING STICK!

A few measurements must be taken before purchasing a septic tank riser system in order to ensure proper installation. The first thing to consider is the size of your opening. Take a measurement of the opening in your septic tank at its widest point to determine the size of your tank. Instead of measuring the existing lid, it’s critical to measure the opening. Because you will be removing the existing lid, the dimensions of the lid are no longer relevant and may differ from the size of the opening itself.

You are now prepared to make a purchase based on these two measurements!

THE COMPLETE RISER SYSTEM

We have a large selection of components from which you may pick to create your own own full riser system. Our many various options offer our product the adaptability to be utilized in virtually any application, but they may also be a bit daunting when attempting to pick which components to buy for a certain application. Each component is discussed in further depth below.

ADAPTER RINGS

The adapter ring is the first component that you’ll need to put together in order to assemble a full riser system. The adapter ring attaches directly to the septic tank, allowing the risers to stack, lock, and mount to it without the need for any additional hardware. Having this component is critical since the risers are not flat on the bottom because they are meant to be stackable, and it is not feasible to install them straight to the septic tank without this piece. The adapter ring provides the flat surface you need to mount to the tank while also being able to accommodate the stackable risers that are included with the tank.

Our square tank adapter ring can accommodate big square apertures up to 25 inches in diameter and large round openings up to 27 inches in diameter.

They are intended to be used with openings that are 24″ or less in diameter.

Concrete anchors, a masonry bit for installing the anchors, and butyl sealer are all included in this set. The use of this installation kit assures a secure mount and a good seal between the adapter ring and the septic tank throughout the installation process.

RISERS

Following your selection of the adapter ring, it is time to go shopping for risers. The Polylok risers are available in two heights: 6″ and 12″, as well as in two diameters: 24″ and 20″. Stackable, each unit has a gasket that has been fitted as well as stainless steel screws to allow for easy installation. Determine which risers will work best for your application based on the height measurement you made between the septic tank and ground level.

OPTIONAL SAFETY SCREEN

In addition to the 20″ and 24″ riser systems, Polylok also produces safety screens that fit within the riser systems. These screens serve as a supplementary layer of protection in the event that the riser cover is unintentionally damaged or removed, and they keep foreign objects from entering the septic tank. They also keep dogs from slipping into unprotected septic tank openings!

RISER LIDS

You will require a lid to complete your riser system, which is the final component you will require. Both the 20″ and 24″ riser systems may be used with the Polylok lids, which are available in two different types to suit your needs. For ease of access, the basic lid is equipped with handles and a gasket that has been factory placed, as well as stainless steel screws to keep it in place. These lids are strong enough to withstand foot traffic as well as the weight of a riding lawn mower driving across them.

• Stainless steel screws are included for installation.
• Installations below grade or in regions with a high volume of foot traffic are advised for the heavy-duty lids.
• The shipping of these items in large boxes necessitates the addition of additional time, materials, and UPS shipping fees.
• If you place your order before 2 PM CST, you will be able to get your order sent the same day you placed it.

FREQUENTLY ASKED QUESTIONS

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered!

WILL THE LID FIT DIRECTLY ON THE ADAPTER RING OR DO I NEED TO USE A RISER?

With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength. The height of this reinforcement is actually more than the height of the adapter ring. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter. The lid will not fit through any aperture less than 24 inches in diameter.

CAN I CUT THE RISER SYSTEM DOWN TO A SPECIFIC HEIGHT?

No, the Polylok riser system is available in increments of 6″ and 12″, and it cannot be customized to a certain height.

Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.

DO I BRING THE RISER SYSTEM JUST BELOW, AT, OR ABOVE GRADE?

It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade. Because the riser system is airtight and watertight, there is no danger in moving it up to or above grade level.

SHOULD I USE THE STANDARD OR THE HEAVY DUTY LID?

The regular lid is sturdy enough to withstand foot activity and weights up to the weight of a small riding lawn mower passing over it without bending or breaking. If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].

The Importance of Septic Tank Risers

When used as intended, the regular lid can withstand foot traffic and weights up to the weight of a small riding lawn mower passing over it without breaking. In areas with high traffic or where the riser system will be run over by lawn equipment on a frequent basis, the heavy-duty lid is recommended for further protection. Further questions should be directed to 1-877-925-5132 or [email protected]

Septic Tank Risers will Lower Your Septic System Cost

On any new or updated septic system in the United States, authorized septic tank risers are required to be built by law in most states. This obligation, in contrast to many other legislative regulations, really provides advantages. Your septic system is one of the most expensive mechanical elements on your property. It is also one of the most complicated. It is also one of the least watched and least understood systems that you have in your possession, as well. If you don’t have septic tank risers, your system will be “out of sight and out of mind” for a long time.

The average cost of a septic system in the United States is around $15,000.

If you add the interest costs to the $15,000 and divide the total sum by the length of time the system will live, your septic system will cost you more than $1,000 a year to maintain.

The installation of septic tank risers is the most effective method of monitoring your septic system.

Advantages of Septic Tank Risers

Septic Tank Riser Made of Concrete The first advantage of an aseptic tank riser is that it is aesthetically pleasing. Every time you see the riser cover, it will serve as a constant reminder that you have a septic tank. This will help you to remember this truth on a frequent basis. Due to the unattractiveness of the old-style concrete covers, many individuals are uncomfortable with the idea of their septic tank risers being visible in their yard. Modern septic tank risers and covers are significantly more aesthetically pleasing, blend in with the surrounding environment, and are easier to install than previous models.

The concrete coverings are similarly heavy, weighing between 60 and 80 pounds.

Riser rings for septic tanks made of modern polymers are generally less than 30 pounds in weight. Because the coverings are lightweight (less than 10 pounds), they are significantly easier to install and maintain.

Modern Septic Tank Risers Seal Surface Water

Septic Tank Riser of the 21st Century The fact that they are more easier to seal than older models means that they are better at keeping surface water from entering the tank. Old-fashioned concrete riser rings do not have a gasket included into them. As a result, surface water may readily flow between the connection between the tank and the riser ring, as well as between the lid and the riser ring, when the tank is filled with water. Nowadays, a watertight seal is installed between the septic tank and the base flange of the riser.

To keep little children from curiously messing with the cover and putting themselves in danger of falling into the septic tank, modern riser covers are fastened with threaded fasteners.

How to Inspect Your Septic Tank

On average, we recommend that you examine your septic tank visually once every six months. Simply removing the septic tank riser cover will allow you to do the check. Remove the cover from the tank and measure the height of the water level in the tank. The water level is typically 6″ to 8″ below the inside of the tank cover when the tank is full. The amount of air space above the water should be between 6″ and 8″ according to this rule. Because of how the clean-out cover is installed on your tank, you may be able to view the septic tank’s inlet or outflow baffle depending on the placement of the cover.

According to the outlet baffle (which should be closest to the drainfield), typical water level should be even with the bottom of pipe or no more than 14 inches deep in the pipe.

Other Benefits of Septic Tank Risers

Another advantage of installing a septic tank riser is that it will make the installation of an Aero-Stream Remediation System relatively straightforward. Take off the riser cover and drop the diffuser assembly and bio-brush into the tank. Then drill a 5/8″ hole in the plastic septic tank riser about 2-3″ below the surface of the water to allow for drainage. Connect the airline to the Aero-Stream aerobic generating unit by pushing it through the hole that has been bored. Done. Simple, Quick, and Efficient!

See How Simple it it to install our Septic Tank Riser

In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below.

Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.

A few safety tips before you get started:

• Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website
• Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.

Gather all the MaterialsTools You will Need

It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.

Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.

Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.

See below for Step 4 on attaching risers to the tank entrance.

1. Tank Adapter Ring (TAR)
2. Riser Adapter Ring Kit
3. Butyl Rope
4. Risers
5. Domed Lid OR Flat Lid
6. Stainless Steel Screws

The following materials will be required for digging up your septic tank(s):

1. As-built condition of the sewage treatment system The following items are required: sketch on paper, measuring tape, shovel, probing instrument, eye protection, and work gloves.

To cut risers to the proper size, the following tools are required:

1. Circular saws, saber/jig saws, and hand saws
2. Raspor file
3. Marking pen
4. Tape measure
5. Drill with a 1/4″ bit

Materials required to seal the risers to the tank include:

1. High-strength concrete patch mix
2. A small bucket
3. A mixing stick
4. And gloves

Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.

Step 1: LocateYour Septic Tank(s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.

Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.

The presence of underground electricity or other utility lines and cables might put your septic tank in danger.

Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.

Step 2: Uncover Your Septic Tank (s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for guidance. This is a plot plan that shows the location of your septic system on your property, as well as the distances between septic components and landmarks. The Online Permit System will guide you through the process of locating septic-related papers if you do not have a “as-built” plan. It may be necessary to contact Environmental Health to examine the paper records, or to hire a specialist to find your tank if an as-built isn’t readily available.

Probing the area around the septic tank with the probing tool until you touch concrete will take some time.

The presence of underground electricity or other utility lines and wires might put your septic tank in danger.

If you run into a power line, the consequences could be fatal. WARNING: Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you start digging.

Step 3: Fit Risers to Component Openings

In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:

• Theriser will fit into the tank hole if the aperture is between 26 and 29 inches in diameter. Measure the distance from the ground to the top of the septic tank and multiply the measurement by three inches. The following is required if the aperture is greater than 29 inches: a 3-foot square fiberglass plate (with a 22-inch hole in the middle) is required. In this case, it lies above the manhole and narrows the aperture, allowing a 24-inch riser to be utilized instead of a more expensive 30-inch riser, saving money.

The distance between the ground and the top of the fiberglass plate should be measured. You may choose to place the risers so that they are level with the surface of the ground, or you may want them to stand out a few inches above the ground (if a riser is above ground make sure you are careful when mowing). Tips: To shorten a big riser with ribs, drill a 1/4-inch hole between the ribs above the cut line and finish the cut by following one of the grooves between the ribs with a saber/jig saw to finish the cut.

By eliminating one of the ribs from the largeriser, it may be made to fit more snugly into a smaller manhole entrance.

Step 4: Attach Risers toSeptic Tank (s)

It is recommended to pump out an old septic tank that is 20 years or older in order to check its structural integrity and water-tightness before using it again. If the tank requires extensive repairs, it is preferable to replace it with a new septic tank that includes risers as part of the installation. A permit from the local health department is required for the replacement of a septic tank. Remove any dirt and debris from the tank’s surface by cleaning it off. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s instructions.

1. Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names available.
2. NOTE: For optimal results, just a little amount of concrete patch should be mixed at a time.
3. The patch mix should be used to seal the riser to the septic tank.
4. If you want to avoid a safety danger, make sure you properly attach theriser lid using the screws that come with it!
5. Risers for inlet or outlet apertures that are smaller than the openings should have the bottom few inches sanded with rough sandpaper to allow a firmer connection between the two surfaces.
6. A useful source of information on correct installation of risers on septic tanks may be found at your local hardware store where you purchased the risers and covers.

Thurston County Environmental Health is should be commended for providing the foundation for this documentation.

What is a Septic Tank Riser and How Do You Install One?

It is recommended to pump out an old septic tank that is 20 years or older in order to check for structural integrity and watertightness. For major problems with the tank it is preferable to replace it with a contemporary septic tank that includes risers as part of the package. A permit from the local health department is required when replacing a septic tank. Remove any dirt and debris from the tank’s surface by wiping it down. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s specifications.

1. Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names that are used.
2. NOTE: For optimal results, use only a tiny amount of concrete patch at a time.
3. The patch mix should be used to seal the riser from the septic tank.
4. If you want to avoid a safety danger, be sure to securely fasten theriser lid using the screws that come with it!
5. When using smaller risers for the inlet or outlet ports, abrasive sandpaper should be used on the bottom few inches of the riser to make a stronger binding.
6. A useful source of information on correct installation of risers on septic tanks can be found from your local hardware store where you purchased the risers.
7. This documentation would not have been possible without the assistance ofThurston County Environmental Health.

Why Do You Need a Septic Tank Riser?

A septic tank riser is required for a variety of reasons, which you may wonder why you require one in the first place. Allow us to explain why you would want to access your septic tank access port in order to have a better understanding of what we are talking about. Whenever you need to empty your septic tank, you must get access to the pump-out outlet on the side of the tank. You will need to pump your tank about every three years, depending on the size of your tank, the number of people living in the house, and the amount of demand placed on the system.

• Find the location of your septic tank. Make a mental note of the region above the access ports (you better hope you’ve properly designated this)
• Dig down as far as you possibly can till you reach the tank.

Depending on the depth of your plumbing and the shape of your land, the depth of your septic tank will vary.

However, it is not uncommon for your septic tank access ports to be around 4 feet below the level of the service line. As a result, if you have a septic tank that does not have risers built, you will have to perform some digging every time you need to reach your septic tank.

What are the Pros and Cons of Installing a Septic Tank Riser?

• The apparent advantage is that you will make it much easier to reach your septic tank pumping port
• Nevertheless, When you need to have your tank emptied, this will save you a significant amount of time and effort. Additionally, if you are unable to perform the digging yourself, you will almost always see an increase in the price of your septic tank service bill owing to the additional time and effort that your pumping business will have to put in when pumping your septic tank. The presence of a septic tank riser will make it easier for purchasers who are inexperienced with septic systems to comprehend the system if you decide to sell your home.

Cons of Septic Tank Risers

• The most significant disadvantage of installing septic tank risers on your septic tank is that the lids will now be visible on the surface of your lawn, which can be a safety hazard. Which might be rather unsightly
• A septic tank riser will need to be installed if your tank does not already have one
• Otherwise, you will have to pay money to have one installed.

Can You Install a Septic Tank Riser on an Older Septic System?

It is quite likely that your septic system will have septic tank risers if you are having a new system installed. For those who have an older septic system, there is the possibility that your present septic system does not have septic tank risers installed. As a result, you may wonder if it is possible to put septic tank risers on an older septic tank. A septic tank riser may be installed on an older septic tank, and this is the correct answer.

How to Install a Septic Tank Riser?

Installing a septic tank riser on an older septic system may be accomplished in two different ways.

1. Obtain the Services of a Septic Tank Professional: This is self-explanatory, but if you’re not handy, like me, you might not realize it. You should next get in touch with a local septic tank specialist and inform them that you have an older septic tank and that you would want septic tank risers to be fitted. To learn more, please visit this page. If you need assistance locating a local septic tank service, please contact us. Installing a septic tank riser on your own is possible if you follow these steps: If you opt to do it yourself, you will be able to successfully install a septic tank riser.

DIY- How to Install a Septic Tank Riser Yourself?

So, if you decide to build your septic tank riser on your own, these are the procedures you will need to do.

1. Septic Tank Riser
2. Transition Ring
3. Caulk Gun with Henry’s Roofing Tar
4. Septic Tank Riser Lid
5. Septic Tank Riser

a septic tank riser with a lid, a transition ring, a caulking gun, and Henry’s Roofing Tar; and a transition ring.

1. Find the location of your septic tank. Place the plants just over the access openings, to be more specific
2. Dig all the way down to the septic tank until you reach the top
3. Remove the concrete tank’s cover and set it aside. Measure the opening on the diagonal, from corner to corner, starting at one end and ending at the other. This will provide you with the information you want on the size of the riser. Make certain that you measure from corner to corner at an angle, otherwise you may end up with a diameter that is too tiny. Connect the Riser to the transition ring and apply the roofing tar where the two pieces come together. Roofing tar should be applied at the bottom of the transition ring. Afterwards, attach the septic tank riser just above the tank access hole.

Please see the video below for a fast demonstration of how to install septic tank risers in the correct manner. Installing your septic tank riser with anchors is a different method than the one described above.

What Brand of Septic Tank Riser is Best?

In terms of choosing an excellent septic tank riser, there are a handful of reliable manufacturers to consider. Tuf-Tite Septic Tank Risers, on the other hand, is the one that truly stands out in terms of consistent customer feedback. Because of this, you may find the Tuf-Tite Septic Tank Risers at your local septic tank wholesaler, or you can get them straight from Amazon, which is even more convenient. Here’s where you can get the most up-to-date pricing on Amazon. (Full disclosure: This is an affiliate link, which means that if you make a purchase after clicking on it, Amazon will provide me with a tiny commission.) If you do decide to go forward with it, please accept my thanks in advance.)

• Adaptive Rings for Septic Tank Riser can be found at the lowest prices on Amazon
• Click here to view the best Amazon pricing on Adaptive Rings for Septic Tank Riser.

Related Question

Polylok septic tank risers and lids are another brand of septic tank risers, lids, and adaptive rings that many people use and that you may shop and compare to the Tuf-Tite septic tank risers is another brand of septic tank risers, lids, and adaptive rings.

Do I need to install a septic tank riser on my septic tank?

Polylok septic tank risers and lids are another brand of septic tank risers, lids, and adaptable rings that many people use and that you may shop and compare to Tuf-Tite septic tank risers.

Can you hide your septic tank lids after installing a Septic tank Riser?

As a result, the purpose of installing a septic tank riser is to make it much simpler to really reach your septic tank, therefore you should be cautious while attempting to conceal it in your yard. Never cover it up with shrubs or with any other permanent building that would prevent you from accessing the port for your septic tank pumping system. However, having said that, I understand that having the lids in the center of your yard can be a little unattractive. Using camouflage style lid coverings, which are made to seem like rocks or other natural features on your lawn, is one option you might consider using.

Take a peek at this page if you want to see some great covers that look like rocks.

Here’s where you can find a local septic tank specialist. For those who require septic system servicing, our state by state list may help you locate a qualified local professional. Simply select your state from the list below.