How To Tell Where Septic Tank Is At On Yard? (Correct answer)

Follow the Main Sewer Line Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside. The sewer pipes will lead to where your septic tank is located.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

Where are most septic tanks located?

Toe the Line. Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.

Will metal detector find septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How do I find out if my septic tank is registered?

Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.

How do I find my septic lateral lines?

Call your local electric utility provider or gas company to locate buried gas or utility lines before digging. A septic tank probe can also help you find the location. Stick the long, thin metal probe into the ground until you feel it hit the tank and feel the edges of the tank.

Do I have to change my septic tank?

Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.

How do septic tanks look?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.

Are septic tanks metal?

Steel Septic Tank—Steel septic tanks are the least durable and least popular tank option. Designed to last no more than 20-25 years, they can be susceptible to rust even before that. Steel top covers can rust through and cause an unsuspecting person to fall into the tank.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.

Inspect Your Property

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.

  • Paved surfaces
  • Unique landscaping
  • Your water well, if you have one
  • And other features.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.

Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.

Don’t Try to Fix Septic Tank Issues Yourself

Having trouble getting this? We can help. Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can use. – Perhaps you will be shocked to learn that there are several ways to obtain information on your property without ever leaving the comfort of your own residence. Structure permits, for example, are frequently found in county records, and they may include schematics with specifications on how far away from a septic tank a building should be, as well as other valuable information such as the size of the tank.

Yet the majority of counties continue to keep track of septic tank installations at all locations.

Schedule Septic Tank Maintenance

The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.

We are open seven days a week, twenty-four hours a day.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.

If you’re also using well water, it’s possible that you won’t receive one at all. If you do not have a meter installed, it is likely that you are connected to a private well rather than the public sewage network.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis.

All of the heavy lifting has been delegated to our team of professionals.

How To Find My Septic Tank

  1. What is a septic tank
  2. How do I know if I have a septic tank
  3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
  4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

  • “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
  • When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
  • The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
  • In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

See also:  How Far Must Septic Tank Sit From House In Florida? (Perfect answer)

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

  1. A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
  2. A septic system is likely to be installed in your home if you reside in a rather rural location.
  3. Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
  4. When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
  5. Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

  1. If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
  2. The county health department is responsible for keeping track of septic systems.
  3. A septic tank’s position could be depicted on a survey map, for example.
  4. The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

  1. In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
  2. By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
  3. The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
  4. Going via the sewage line itself is another method of locating the septic tank utilizing it.
  5. Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
  6. When the snake comes to a complete halt, it has almost certainly reached the tank.
  7. While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
  8. When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

  • Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
  • Directly in front of the home Immediately adjacent to your well (if you have one)
  • In close proximity to trees or densely planted regions
  • In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

See also:  How To Abandon A Septic Tank In Mchenry County Illinois? (Perfect answer)

Request an Estimate for the Job

How to Locate Your Septic Tank

It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.

This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.

How To Find A Septic Tank: Step By Step

It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.

1. Gather Some Helpful Tools

Septic tank location can be made much easier with the use of some simple tools and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.

Using this method, you may also locate the cover for your septic tank.

While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.

2. Use a Septic Tank Map

If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.

3. Start Ruling Areas Out

The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:

  • Immediately adjacent to your well
  • Beneath your home
  • Directly against your home
  • For example, underneath your driveway
  • Under trees
  • And other locations. Structures like a patio or deck are good examples of this.

4. Inspect Your Property

If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.

When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.

The likelihood of your septic tank being discovered in a few specific locations is quite high. Because of code issues or just because it doesn’t make sense, it’s highly unlikely that your septic tank will be located near any of the following locations:

  • Your water well, if you have one (for a variety of reasons that are rather clear)
  • Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
  • Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
  • Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping

5. Inspect Your Yard

A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:

  • If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
  • Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.

The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.

6. Follow Your Sewer Main/Sewer Pipes

Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.

The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.

If the line is labeled, it is usually made of plastic or rubber.

7. Check Your Property Records

Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.

If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.

What to Do Once You Find Your Septic Tank

Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities.

You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!

How do I find the septic tank in my yard?

Q:Can you tell me where my septic tank is located in my yard? As a first step, determine the place where the main drain line (4-inch pipe) exits your property. This will show whether or not the tank is located just outside of that area. With a metal probe, trace the pipe across the yard, probing every 2 feet along the way. It is essential that septic tanks be at least 5 feet away from the home, although most are between 10 and 25 feet away. They are generally rectangular in design and measure roughly 5 feet by 8 feet in length and width respectively.

You can use a metal probe to detect the boundaries of the object and mark the perimeter of the object.

Depending on when you acquired the property, a schematic of your septic system may have been provided as part of your home inspection.

EHT Newsletter

Become a member of the EHT Newsletter and receive monthly DIY advice as well as industry developments, trends, and more.

Hot Product

For optimum corrosion protection, Maze STORMGUARD® nails are double hot dipped galvanized and feature a thick zinc coating to provide maximum corrosion resistance. All Maze STORMGUARD® Nails are hot-dip galvanized to meet or exceed the ASTM A 153 criteria for galvanizing. For fiber cement siding, cedar and redwood siding, roofing, cedar shakes and shingles, PVC trim products and other applications, Maze offers premium double hot-dipped nails. More information can be found at

How to find your Septic Tank at Home

When was the last time you paused to think about what happens to the things you flush down the toilet? It’s a little disgusting to think about, isn’t it? It’s possible that you’re conjuring up images of cobwebby crawlspaces with a swarm of creepy-crawly unmentionable creatures sliding, slithering, creeping, or crawling over crusty, rusted, ooey-gooey piping that’s oozing slimy goo from every joint. If this sounds like something you’re picturing then you’re not too far off the mark. I sincerely hope you are.

  • That’s why I’d want to assist you in learning how to locate your septic tank.
  • Simply dial 911 and ask for assistance in a calm manner.
  • Most hide-and-seek games are won by septic tanks, which are well-known for their amazing ability to outperform the typical human rival.
  • The good news is that.
  • Contrary to common misconception, septic tanks are not often found in attics, basements, or any of the numerous closets that may exist in a house or apartment.
  • Relax in your favorite place for a few minutes with your favorite beverage in hand.
  • Yes, you read that correctly: your yard.

Alternatively, you can sink.

Or whatever it is that’s causing the terror to rise in your chest to rise in your chest.

Septic tanks are normally installed in one of your backyards or on your property.

How are you doing?

If your septic tank is in close proximity to your well, this should be avoided.

Septic tanks are often located on the other side of a house from where your home is located.

Tanks are often placed with their tops buried beneath the surface of the ground, usually at least 12 inches below the level of the ground’s surface.

A plastic access tube or a concrete riser structure that runs from the top of the tank to the ground level will often be included to give access for a Septic Pumping firm to empty the tank. Shankster Brothers (also known as Shanksters)

Many septic tank installers will attempt to blend these access risers into the surrounding landscaping so they don’t create an ugly eyesore.

So the next step is to mentally go about your yard, looking for any circular, plastic lids that could be lying around. These can range in size from 10 inches to 24 inches in diameter and can be either black or green. Second, if the answer is no, consider any round, square, or rectangular concrete lids that may be present in your yard or landscaping as a possible source of contamination. Often, they will be practically flat with the surface of the ground, allowing a lawnmower or rake to pass directly over the top of them without causing damage.

  • Typically, the septic tank access will be no more than 10 feet away from your home, but in the event of an older home or a subsequent addition to the property, they may be closer than that.
  • Hopefully, you have a basement to store your belongings.
  • If your home does not have a basement or crawlspace, we will rely on other indications to locate your home.
  • All of these pipes should converge into a single bigger pipe (usually 4 inches in diameter) that exits the house via one of the home’s walls.
  • Now it’s time to go outdoors.

Check the area where the pipe comes out of the house. There may be a PVC pipe extending to the surface, with a threaded cleanout cap on it. If you find this, you’re well on the way to victory.

Take a check at the roof if your property is constructed on a slab with no basement or crawlspace beneath it. Check the roof for a vent pipe that is coming out of it. An internal vent that travels straight up, through the roof, and out the top of your home is common. If you can identify that vent, it might be possible to figure out where the pipe is departing the house. Continue walking outside from the house for a few steps, keeping an eye out for that round, square, or rectangular cover. If you can’t discover it, check for a little sunken place in the yard that could be hiding anything.

See also:  Where Does The Septic Tank Leak From When It Fails? (TOP 5 Tips)

If you notice one of those, you might want to look underneath it to see if there is an entry point hidden there.

It’s possible that here is where your tank is lurking. If none of these suggestions have resulted in victory, and you begin to observe your neighbors peering through their blinds with those anxious glances that neighbors are so prone to giving.give us a call!

We have foundseptic tanksin many strange and unpredictable places. Here’s hoping you win the game on how to find your septic tank. Here tanky, tanky, tanky! If you need to schedule aseptic tank cleaning, pumping, or inspection, don’t hesitate to call Shankster Bros at(260)-982-7111. any time.

“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.

Why you need to know where your septic tank is located

If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.

In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.

How to find your septic tank

  1. Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
  2. Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.

After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.

  • The post was published on July 16, 2019 under the category Septic Tank System.

How to Find My Septic Tank Lines

Credit: Petegar/E+/Getty Images for the image

In This Article

  • Septic System Fundamentals
  • Identifying and Locating a Septic Tank on Your Property
  • Conducting Regular Inspections
  • Checking for Clean-Outs
  • Identifying Natural Indicators
  • Viewing System Diagrams
  • Seek Professional Assistance
  • Check the distribution box
  • Understand the size and scope of the project.

Are you curious about the location of your septic lines? It is critical to know where the septic tank is located on a property in order to properly manage and preserve the system. For example, you don’t want to pave over the ground or grow trees too close together in a forest. It is possible to obtain a copy of the septic tank diagram of the drain field, which will give you a fair sense of where the pipes will go. If this is not the case, you may need to attempt some other methods of locating septic drain lines.

The solids and liquids are separated within the tank by a baffle or wall that is built inside the tank.

When pipes get clogged or when drain fields become too saturated with fluids, problems arise. Other issues might arise as a result of incorrect placement, design defects, or bad installation.

Locating a Septic Tank on Your Property

Begin your search for the septic tank lines at the residence first. Drain lines from the home’s plumbing should be traced to the septic tank, which is typically located 10 to 20 feet from the home’s exterior. The drain line connects the tank’s end, which is located opposite the house, to the leach field. Check the natural slope of the ground to see whether the leach field may be found there. It is never a good idea to search for drain lines with heavy machinery, wrecking bars, or jackhammers.

A septic tank probe can also assist you in locating the tank’s position.

This might assist you in locating the pipes that lead away from the tank.

Perform Regular Inspection

According to industry experts, you should examine your septic tanks and, if required, pump them out once every three years. If you are experiencing gurgling sounds in your house or water backing up after your system has been repaired, a saturated drain field might be the source of the problem. Drain fields that have been clogged or damaged are unable to be rectified. In order for the septic system to function properly again, you’ll need to have a new drain field installed. Find capped clean-outs that are a few inches vertically above the ground in the leach field itself, or check behind a wall or in a closet in the basement for capped clean-outs.

  1. You can visually trace the orientation of the pipe from the clean-out if there is no other information available.
  2. Credit: Kyryl Gorlov/iStock/Getty Images for the image.
  3. When you are looking for the lines, look for grass or vegetation that greens in stripes when the grass surrounding it browns.
  4. Putting hot water into your system might cause snow or ice to melt above the drain pipes if the system is not properly insulated.
  5. If you have a deep system, as is the case for homes with basements, you will most likely not be able to observe natural signs since the drain field is too deep to be seen from above.
  6. Unless the system was built without a permit, the blueprints or designs for septic system installations are kept on file with the local health authority until the system is operational.
  7. If your search does not provide any relevant results, you can request a record search based on your street address or the tax account number associated with the property.
  8. If the agency has a copy of the record, they will mail it to you.
  9. If you don’t have a drawing of the septic system, you need enlist the assistance of a disposal system contractor or a certified liquid waste transporter to find it.

Another option is to purchase a flushable transmitter from a plumbing or rental business, or you may contract with a tank cleaning firm. The signal from the transmitter is picked up by a hand-held receiver after it has been flushed down the toilet.

Check the Distribution Box

There are certain septic tanks that feature an extra distribution box that is located a few feet from the tank on the tank’s downstream side. Water is channeled into the trenches by ports and pipes in the box. It is recommended that, if your system includes a distribution box, the box’s top be designed to expose the orientation of the ports that connect to the drain field lines. It is feasible to locate the box with a probe, but extreme caution should be exercised. Avoid applying excessive force to the probe, since this may result in damage to the box.

In most cases, individual drain lines run perpendicular to the intake line, but they may also branch into an H-pattern or other patterns that are appropriate for the terrain.

Find the location of your septic drain lines so that you can safeguard the area in and around them with a little detective work.

How to Locate Your Drain Field

Homeownership entails a large number of duties. Making repairs to the house, keeping the lawns, caring for the landscaping, paying all kind of bills and taxes, and a slew of other responsibilities are required. But it’s all worth it when you finally get to purchase your own house. Consider the following scenario: you have acquired a home in Modesto, CA that has a septic tank installation. Regardless of whether you are familiar with septic systems or not, you must be aware of the location of the tank and drain field.

In light of this, we would like to provide you with some expert guidance to assist you in locating your drain field.

A few sewage system pipe routes are easy to identify in the yard, while others are more difficult to locate.

  • First, take a look around your yard. It’s typical for you to not notice any indicators of your drain field’s presence at first sight. For starters, go around your yard, checking for lines of green grass, dead grass, and sunk-in regions (front, rear, and sides). If you see any of them, go ahead and investigate since these are indications of a drain field installation. Examine the surrounding region for markers: Ideally, a cement marker the size of a manhole cover should be used to indicate the position of your septic tank. Try to find it between 10 and 20 feet away from your house. As soon as you’ve located the tank, head down the steepest slope and look for an empty downward-sloping field to hide in. It’s possible that you’ve just discovered your drain field. Check your yard for gravel by doing the following: Another option is to probe your yard and feel for gravel, because drain field lines are covered in gravel as a manner of guiding wastewater through the treatment process and are therefore difficult to detect. If you come across gravel, you may have discovered your property’s drain field. Please be aware that probing may be difficult in regions where the soil is hard or rocky
  • Thus, caution is advised. Examine the county’s records: A copy of your property’s septic records may be on file with your county’s permits department or with the business that built the septic system in its first place. Read the notes left by past owners: Another option is to inquire with the former owners about the location of the drain field. Even if this isn’t possible, look in the garage, cupboards, and bathroom areas for notes or instruction manuals that may have been left for you by the previous residents. When people are preparing to move, they may gather all of the owners’ manuals or write out their own notes on how to use and maintain specific appliances or systems in the house, as well as important information about the products (age, maintenance records, and so on). There’s also a chance that they’ve sketched out the location of the drain field. Request information from neighbors:You should make yourself known to your immediate neighbors as soon as possible after moving into your new house. This is an excellent moment to inquire as to whether or not they are aware of the location of your drain field.

Alvarado Pumping Septic Service is the company to call in Modesto, California, for the best septic maintenance, drain field services, and septic tank installation you can find. Our septic system professionals are here to assist you at any time with your house or business’ septic system!

Leave a Comment

Your email address will not be published. Required fields are marked *