How To Remove Aerator Lid On Septic Tank? (Perfect answer)

  • The majority of septic tank lids will require a pry bar to lift them out of their seating. Set the prybar in the seam and press down. As the lid lifts out of the hole, have someone move it to the side.

How do you remove a septic tank lid?

Some tank lids have built-in handles to pull on, but others require a pry bar to lift them open. If the lid comes with handles, ask for the assistance of a friend or family member to remove the lid. If it doesn’t, push a screwdriver into the seam around the lid and insert the pry bar into the gap. Then, press down.

Why does my septic tank have 2 lids?

Solid, watertight, buried tank made of concrete, plastic, fiberglass or metal. This tank has a way in (inlet), and a way out (outlet). So, most residential tanks should have (2) lids about 5′ away from each other. A septic tank holds all the liquid waste from your home (toilets, sinks, kitchen, bathtubs, floor drains).

Why is water coming out of my septic lid?

The top of the septic tank is usually a few feet below the soil. If you see standing water above the drainfield or tank, your septic system is likely flooded. When you don’t see obvious standing water over the area, check the water level with a probe, or use an auger to dig down into the soil.

Should a septic tank lid be sealed?

Like wells, septic systems have problems if they are not sealed from outside surface water. Most septic systems rely on buried pipes to get rid of the fluids. The lid covers should fit tightly — if they don’t, a company that specializes in septic repairs should be called to fix them.

How far apart are the lids on a septic tank?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

How often should you clean a septic tank filter?

As a rule of thumb, you should always clean the septic tank filter when doing your routine pumping. But since this will typically be after a couple of years, you should inspect the filter twice a year – just before winter and right after winter. It is best to use a filter that has an alarm.

Why does my septic tank filter keep clogging?

A properly working septic tank outlet filter will become clogged as effluent is filtered and leaves the septic tank. As the solid materials accumulate over time, they progressively clog more and more of the filter, requiring maintenance. They should also be cleaned when you get the tank pumped and cleaned.

How do you tell if your septic tank is full?

How to tell your septic tank is full and needs emptying

  1. Pooling water.
  2. Slow drains.
  3. Odours.
  4. An overly healthy lawn.
  5. Sewer backup.
  6. Gurgling Pipes.
  7. Trouble Flushing.

How do I know if my septic tank has two lids?

Locate The Lid A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle. A shallow excavation with a shovel at those locations should reveal the lid or lids, depending on the year of the tank.

Do all septic tanks have lids?

Find the Lid. If your septic tank was installed after 1975, it will probably have two polyethylene or fiberglass lids centered at opposite sides of the perimeter. Older tanks will typically have a 24-inch concrete lid right in the center of the tank. Excavate in those locations to reveal the lids.

How can you tell if your leach field is failing?

The following are a few common signs of leach field failure: Grass over leach field is greener than the rest of the yard. The surrounding area is wet, mushy, or even has standing water. Sewage odors around drains, tank, or leach field.

Can I shower if my septic tank is full?

Only the water would get out into the leach field in a proper system unless you run too much water too fast. The thing to do is to run your shower water outside into it’s own drain area, but it may not be allowed where you are. Used to be called gray water system.

How do you fix a septic tank that backs up when it rains?

After a major rain event, the only way to relieve pressure on the system is by using it less. If possible, reduce or eliminate water going down the drains until the drainfield dries out. An emergency septic service cleaning can provide temporary relief, but this is often a futile exercise in battling mother nature.

Will a flooded septic tank fix itself?

Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.

Aeration Septic – Septic Tank Risers and Lids

Septic tank lids, risers, and covers are an excellent method to save time and money while also increasing safety around the septic system and preventing flooding. Installing septic tank lids and risers to bring access to your system up to code can save you the money you would otherwise spend on having your system dug up every time it has to be pumped. If you replace heavy concrete lids with lightweight yet sturdy and durable plastic lids that can be attached securely to protect the safety of children and dogs in the vicinity of the system, you may save your back.

Polylok Septic Tank Risers and Lids

12″ x 6″ Septic Tank Riser made of Polylok

  • Extra strength is provided by heavy-duty structural rib reinforcing. For UV-Rays, a green opaque hue is used. Molded warning signs that are clearly visible for safety
  • Frost is prevented from clinging to frost prone locations by structural ribs on the interior.

Riser Lid for Septic Tank with Polylok 12″ Lid

  • Surface that is skid resistant
  • The highest level of UV protection currently available
  • In order to dissuade unwanted entrance, square drive screws are used.

Septic Tank Riser Polylok 20″ x 6″ Polylok Septic Tank Riser

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction. Frost is prevented from clinging to frost-prone locations by structural ribs on the interior.

Septic Tank Riser Polylok 20″ x 12″ Polylok 20″ x 12″

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction.

Riser Lid for Septic Tank with Polylok 20″ Lid

  • The surface is slip-resistant, and it has two recessed handles for simple removal. The most effective UV protection available
  • In order to dissuade unwanted entrance, square drive screws are used.

The Polylok 20″ Heavy Duty Septic Tank Lid is made of polypropylene.

  • Surface that is skid resistant
  • The highest level of UV protection possible
  • It has a foam gasket to provide an airtight and waterproof connection. In order to dissuade unwanted entrance, square drive screws are used.

The Polylok Septic Tank Riser measures 24″ x 6″.

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction. Bring the septic access up to grade in no time

The Polylok 24″ x 12″ Septic Tank Riser is made of polyethylene.

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction.

Riser Lid for Septic Tank with Polylok 24″ Lid

  • The surface is slip-resistant, and it has two recessed handles for simple removal. The most effective UV protection available
  • In order to dissuade unwanted entrance, square drive screws are used.

Alternatively, you may phone us at 330-236-1561.

Tuf-TIte Septic Tank Risers and Lids

Tuf-Tite 20″ x 6″ Septic Tank Riser is made of polyethylene.

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite 20″ x 12″ Septic Tank Riser is made of polyethylene.

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite Heavy Duty Septic Tank Lid, 20″ in Diameter

  • Air and watertight connection made possible by a foam gasket
  • Heavy-duty, long-lasting structure

Tuf-Tite Septic Tank Riser (24″ x 6″ x 5″)

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite Septic Tank Riser (24″ x 12″ x 4″

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite Heavy Duty Septic Tank Lid, 24″ in Diameter

  • A foam gasket is used to ensure an airtight and waterproof connection. Heavy-duty, long-lasting structure
  • Screws made of stainless steel are provided.

Tuf-Tite Domed Septic Tank Lid, 24″ in Diameter

  • Screws made of stainless steel are supplied
  • Two horizontal safety screws are also included.

The SepAerator™ Septic Tank Aerator Installation Instructions

The SepAeratorTM is relatively simple to install into an existing septic tank and may be completed in the following steps:

  1. Find the lids that cover the input and outflow portions of your septic tank by digging down. A 12 inch spa-flex airline should be attached to the diffuser assembly and lowered to the bottom of your septic tank’s inflow part. (See illustration.) Attach the other end of the 12 spa-flex airline to the air pump, which will easily plug into a standard 115-volt outlet
  2. And Install the filter assembly at the discharge end of your septic tank, where it will connect to the outlet line. It should adhere to the surface. We even provide the adhesive
  3. Just let us know.

Note: Because the diffuser assembly would only be cleaned on a very infrequent basis, risers above this component would be unnecessary. In order to protect the Air Driven Particle Recirculation System or filters included in some packages, we propose that you install our optionalriser and lid kits, which would extend the septic tank opening to, or slightly above, the ground level, rather than using the included filters. This is required in order to provide simple access to these critical components, which would need to be removed and washed with a garden hose on a regular basis.

The filter is a required and essential component of any aerobic conversion kit, and it will need to be cleaned on a regular basis to keep it operating properly.

SepAerator™Premium Package Detailed Installation Instructions

A SepAeratorTM may be installed on an existing septic tank in as little as a few hours since the installation process is so straightforward. Even those with very basic mechanical abilities can install a SepAeratorTM on an existing septic tank. Please verify with your local authorities because rules differ from county to county and state to state. Local rules may demand that the SepAeratorTM be installed by a licensed septic system installationcontractor in order to be compliant. 1. Identify the location of your existing septic tank.

  1. Performing regular pumping is vital to remove all of the particles and sludge that has accumulated in your tank.
  2. Then, once you’ve discovered your septic tank, you’ll need to identify two areas on the tank.
  3. At these areas, dig down to the tank’s bottom and remove any existing covers.
  4. Install the Air Driven Particle Recirculator on the recirculation system.
  5. To install the Air Driven Particle Recirculator, first remove any existing baffles, then clean the pipe and glue the device to the outlet.
  6. With a minor level, you can verify this claim.
  7. Schedule 35 and 40 pipe, as well as the expand n lok adapter, are compatible with the filter tee.

a.

When installing the Air Driven Particle Recirculator, if you got the Premiumpackage, you must connect the little 14-inch airline that came with it to the adapter fitting at the top.

Transfer to the front compartment of the septic tank and secure the current cover to the septic tank.

You’ll need a hole with a minimum diameter of 8 inches for this.

INSTRUCTIONS FOR INSTALLING OPTIONAL RISERS AND LIDS ARE INCLUDED.

Place a bead of caulking or sealant over the bottom of one of the tank adapter rings and let dry.

Place the riseron adapter ring on top of the riseron and secure it with screws.

See also:  How To From Septic Tank To Sewage Grinder Pump? (Solution)

This will make it possible to have access to the components as necessary for periodic maintenance and examination.

Note: If you have a single compartment septic tank, it is required to install an Air Driven Particle Recirculator on the outflow line of your septic tank.

4.Assemble and attach the Diffuser Assembly to the wall.

The airline has previously been joined to the top section of the diffuser assembly.

Lower the diffuser assembly into the septic tank through the aperture above the intake until it rests firmly on the bottom of the tank.

Take all required steps to ensure that your septic tank remains watertight following the installation of any components.

5.Connect the Diffuser Assembly to the Air Pump using the connectors provided.

Attach the 14-inch airline from the septic tankfilter to the fitting supplied on the air pump at this point, if you are using ourPremium Package as well.

Air pump installation at a distance may be accomplished by gluing 12 schedule40 pvc tubing or more spa-flex to the diffuser assembly and air pump installation at a distance.

Place the platform at a sufficient height so that the air pump does not flood.

Keep dirt and other debris away from the bottom of the housing.

7.An optional alarm and control panel is available.

It is important to note that a least of 14-2 underground cable must be laid to power the alarm.

Once the 115-volt electrical connections have been established, the power should be turned on.

8.Inspect and backfill all risers and power lines thoroughly.

This is required in order to prevent the danger of tank floating as well as to ensure appropriate operation of the pump and diffuser assemblies.

It is intended for the air pump to operate on a continual basis.

The majority of pumps consume less than 2 amps.

The little filter positioned on top of the air pump should be removed and cleaned with air or water once every six months, and it should be changed once every twelve months.

In order for a considerable volume of germs to grow, it may take between 4 and 12 weeks.

In each state, there are several types of installations. It is solely the responsibility of the end user (homeowner/purchaser) to ensure that the items are installed in accordance with all applicable county/state/federal laws, rules, and guidelines currently in place before using the products.

How to Remove a Septic Tank Lid

A septic tank lid is the section of the sewage tank that is located at the top of the tank. This lid must be removed at least once every several years in order to completely empty the tank. Every three to five years, depending on the size of the tank, a homeowner will need to have the septic tank pumped out and cleaned. Avoid allowing the tank to become overflowing, causing it to begin backing up into the home or overflowing out of the opening. The tank suffers serious damage as a result of this.

Step 1 – Locate Septic Tank

A septic tank lid is the section of the sewage tank that is located at the top of the tank. This lid must be removed at least once every several years in order to completely empty the tank. Every three to five years, depending on the size of the tank, a homeowner will need to have the septic tank pumped out and cleaned. Avoid allowing the tank to become overflowing, causing it to begin backing up into the home or overflowing out of the opening. The tank suffers serious damage as a result of this.

Step 2 – Dig Up Septic Tank Lid

A septic tank lid is the section of the sewage tank that is located at the top of the tank. This lid must be removed at least once every several years in order to completely empty the tank. Every three to five years, depending on the size of the tank, a homeowner will need to have the septic tank pumped out and cleaned. Avoid allowing the tank to become overflowing, causing it to begin backing up into the home or overflowing out of the opening. The tank suffers serious damage as a result of this.

Step 3 – Pry Off Septic Tank Lid

The lid of the septic tank might be rather hefty, depending on the size of the tank. On all sides, it is a solid block of concrete that is perfectly flat. It could have a handle that you can pull on. Pry bars are required to remove the majority of septic tank lids from their resting positions. Set the prybar in the seam and push it down until it is secure. As the lid begins to rise out of the hole, have someone assist you in moving it to the side. Place the lid on the ground’s surface so that it is not in the path of the pumping vehicle.

How to Install a Septic Aerator

A septicaeratoriis a relatively basic and straightforward piece of equipment to install in your septic system. The aerator is particularly beneficial for older septic systems since it contributes to the addition and provision of a significant amount of oxygen to the septic system. The presence of oxygen in the waste that flows to and from your septic tank is a critical component of the breakdown process.

A professional can often complete the installation of this equipment in a matter of hours. A person who is reasonably handy may require a little more time to install the product. The procedure is, on the other hand, manageable and quite straightforward.

Step 1 – Familiarize Yourself with the Unit

As soon as you have acquired the sepic aeration system, you should bring out the instruction manual and go through the information that is contained within that particular item. Make certain that you have gone over all of the specifics. Learn about the parts, components, and factors that make up your new system so that you are comfortable with them. If you have any questions, you should contact with a specialist that specializes in the installation of these sorts of systems. Step 2 – Have the land surveyors come out and measure it.

  • A survey will be required if you wish to apply for a construction permit to install the septic system on your property.
  • Before you can start working on your septic system, you must first apply for a permit and submit a schematic of your system to the appropriate local government agency.
  • To find out who you need to contact in order to obtain the application, seek up the phone number or the location of your local township or municipality on the internet.
  • They will be able to point you in the direction of the application process.

Step 4 – Install a Riser and Lid Kit

If you do not already have a riser and lid kit installed on your septic system, you should purchase one. Install the kit first, then proceed to install the aerator. This will make it easier for you to acquire access to your septic system for future renovations and work. Each riser and lid set is unique in its own way. Make certain that the instructions provided by the manufacturer are followed.

Step 5 – Install the Aeration Pump

The aeration pump must be put at a reasonable distance of your residence. The pump is directly connected to the aerator (which was built in Step 3) and will assist in pumping in the additional oxygen that is required in the tank.

Step 6 – Install the Aerator

In the septic tank, the aerator is directly connected to the tank’s pump. It has to be pushed all the way down to the bottom of your septic tank to be effective. The seventh step is to close the lid on your septic system. Step 8 – Clean Up and Wash EverythingWash and clean everything thoroughly. You have just finished working in an environment that contains millions of bacterium particles. Make sure to wash your hands with an anti-bacterial soap or solution when you’ve finished.

Septic Tank Risers, Lids, and Covers

Septic tank risers are intended to replace existing concrete, fiberglass, or metal septic tank lids by lowering the entrance to the ground level and allowing for better drainage. Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.

We use high-quality, heavy-duty polyethylene plastic to construct our Polylok risers and lids, which allows them to be extremely robust and durable while also being lightweight and simple to handle. With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!

Septic tank risers are intended to replace existing concrete, fiberglass, or metal septic tank lids by lowering the entrance to the ground level and allowing for better drainage. Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.

With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!

FREQUENTLY ASKED QUESTIONS

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered! Would the POLYLOK SEPTIC TANK LID fit directly on the ADAPTER RING, or will I need to use a RISER to ensure a proper fit on the tank? With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength.

  1. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter.
  2. ALL other Polylok lids will attach straight to the adapter ring, eliminating the need for a riser or any other adaptor.
  3. No.
  4. Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.
  5. It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade.
  6. IS IT BETTER TO USE THE STANDARD LID OR THE HEAVY DUTY LID?
  7. If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended.
  8. Yes.
  9. IS IT INCLUDED WITH THE POLYLOK SEPTIC TANK RISERS AND LIDS TO USE SCREWS?
  10. The Polylok Septic Tank Risers are assembled using stainless steel screws that allow them to be connected to one another.

THE POLYLOK SEPTIC TANK RISER ADVANTAGE

Riser systems are available in a variety of shapes, sizes, and designs on the market today. The Polylok septic tank risers are, without a doubt, the best money can buy in this category. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight!

Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

The Polylok risers are reinforced with structural ribs that run internally around each riser segment, providing them with exceptional strength and allowing them to maintain their shape even after the hole is backfilled with dirt. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

See also:  How To Run Brown Water Pipe To Septic Tank? (Solved)

LOW PROFILE RISER LIDS WITH HANDLES

The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE TANK ADAPTER RING

It is necessary to use an adapter ring in order to attach risers to your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

STAINLESS STEEL SCREWS INCLUDED

At Septic Solutions, we strive to make the buying and installation process as simple as possible for our customers. All of our Polylok risers and lids are delivered with all of the stainless steel screws required for installation in one package.

SepAerator® Frequently Asked Questions

WHAT IS THE DIFFICULTY LEVEL OF INSTALLING A SEPAERATOR® PACKAGE? Installing a SepAerator® is a reasonably straightforward process. An experienced septic system contractor can often complete the installation in a couple of hours, while a handyman homeowner may require a bit more time. Each SepAerator® is shipped with a comprehensive Owner’s Manual that includes installation instructions, as well as technical support if needed from our technical support staff. HOW SOON WILL I BE ABLE TO SEE RESULTS AFTER INSTALLATION?

The clear and odorless discharge will enter into your secondary treatment system and begin working on the secondary treatment system immediately, with notable benefits seen within the first 4 to 6 weeks of treatment time.

When the SepAerator® is left running for an extended period of time, the field or secondary treatment system will continue to clean itself as aerobic bacteria break down the accumulation of waste that has gone through the existing septic tank and is now obstructing the secondary treatment system.

  1. When compared to the cost of a new septic system, this will save you thousands of dollars.
  2. In fact, if you don’t already have access to your septic tank through existing risers and lids, you should consider installing our riser and lid package.
  3. Access to the diffuser is optional since you would only need to remove it very seldom for cleaning purposes with a garden hose (perhaps at the same time you pumped your tank, which should be done every 3 to 5 years), and hence it is not required.
  4. This filtering device should be installed in septic tanks with single compartments in order to avoid the chance of tiny particles being driven into the secondary treatment system by the continual movement of water induced by the SepAerator® diffuser, which is installed in the tank.

Even though a two or three compartment septic tank reduces the likelihood of particles exiting your tank as a result of its additional compartment walls, the SepAerator’s® unique filtering assembly provides a final polishing of the discharge, which is a very important step toward extending the life of an existing secondary treatment system or field.

  1. Every six months, you would need to clean the little filter found on top of the air pump using either compressed air or water.
  2. Given that this is a self-cleaning filter, some users have reported lasting more than a year between cleanings; however, in cases of heavy usage, such as regular use of a waste disposal or a higher than usual number of individuals using the system, more frequent cleanings may be required.
  3. The handle on the filter protrudes above the sewage pipe.
  4. After that, reinstall the filter in the housing and replace the top on the tank.
  5. Despite the fact that the SepAerator® will function extremely efficiently and fast in a septic tank that has not been pumped, we feel that it is critical to remove all of the sludge that has accumulated in your septic tank over the course of time.
  6. Furthermore, without pumping, a significant quantity of sludge build-up would need to be broken down and converted into clear liquid before discharge could take place, which would significantly hinder the rejuvenation process.
  7. AFTER INSTALLING THE SEPARATOR, WILL I EVER NEED TO PUMP AGAIN?

This is completely incorrect.

Those would have to be blasted out at some point as well.

A septic tank or aerobic system should be flushed at least once every five years, according to our standard advice.

“That is why you have us here today looking at rebuilding your septic system,” I say in answer to them.

You are under no need to do so; nevertheless, if you do not, the repairs to your engine will almost always be far more expensive than the original cost of the oil change.

No, you can choose to have the air pump located remotely if you so choose.

We strongly recommend that you retain the air pump near the septic tank since it will minimize the need to run an additional air line.

HOW COME I SHOULD PURCHASE THE SEPAERATOR® RATHER THAN COMPETING PRODUCTS?

The SepAerator® was created by a group of professionals who have been in the septic system installation and maintenance business since 1989 and have a combined total of more than 50 years of expertise in the field.

The SepAerator® was created with the goal of providing homeowners with an existing septic tank the chance to easily and affordably upgrade their existing septic tank system in order to take advantage of the most up-to-date aerobic technology now available.

Most competing systems use air pumps that are far smaller than what we consider to be essential.

The diffuser assembly, which is the second most critical component, ensures enough air distribution as well as efficient effluent circulation, allowing the aerobic bacteria to complete their tasks as rapidly as possible after being introduced into the system.

Last but not least, our unique Air Driven Particle Recirculator, which sets our SepAerator® apart from the competition, is a critical component in achieving superior performance.

It is critical that this movement does not result in any premature release of particles from the septic tank into the existing field or secondary treatment system during the construction process.

This may be performed by the installation of the appropriate sort of septic tank filtration system.

We at Septic Solutions, Inc. have addressed this issue via intensive testing and have created our self-cleaning fixed media filter over the course of several years. This is the first and only instance of its sort. This product is really simple to set up and to maintain.

Prevent Costly Repairs: Septic Aerator

Those enigmatic concrete or plastic lids you see when mowing the grass are really septic systems, which are also known as Household Sewer Treatment Systems (HSTS). That one component of the house that everyone is aware of but knows little about, and for that matter no one wants to know about. It’s the one component of the house that everyone is aware of but knows little about. In addition, your septic system is the one component of your property that receives the least amount of attention or upkeep.

  1. However, when the system fails, we are taken aback, and then furious, when the invoices from septic and sewer professionals arrive, which are often in the hundreds of dollars range.
  2. Make certain you obtain these from your builder or to call your local health agency, which provides this information at no cost to the general public.
  3. The internet is a fantastic resource for product identification, component and part information, and so forth.
  4. One of the most frequently neglected difficulties is the failure to get your system pumped and cleaned on a regular basis.
  5. Failure to pump and remove the accumulation can result in backups, obstructions and system foulness as well as the mechanical failure of aerators and pumps in a septic system.
  6. The presence of chemicals and other dangerous containments in failed septic systems and HSTSs is the second most serious problem associated with these systems.
  7. The majority of householders are unaware that flushing bleach, paint, cleansers, and other toxic chemicals down drains and toilets is destroying the bacteria in their system, which is a serious health hazard.

Aeration is another crucial subject that is sometimes disregarded, or even worse, interfered with, in the garden.

Modern systems have more integrated septic aerators installed than older types that employed drop-in models as part of their design.

Mechanical failures in aeration equipment are simpler to detect nowadays, thanks to alarms installed within the home that alert the property owner when the septic aerator is not functioning properly.

As the air created by the septic aerator is driven into the aeration chamber (which is typically the second lid downstream from the home), the bacteria in your system are aided in their efforts to break down the solids and influent.

One final point to remember about aeration is to make sure that any backwashing feeds from your well water system softener are kept separate from the septic or HSTS.

Salt and brine backwashing systems include high concentrations of sulfur and acids, which can cause early erosion of concrete tanks and other tank-related components.

FAQs About Septic Tank Aerators

It’s possible that you’ve recently moved into a home that has an aeration system or an aerated septic tank, or that you’re looking to install a new ATU to repair your current septic system, that you’re looking for answers aboutseptic tank aerators. If this is the case, you’ve come to the right place. Depending on where you reside and what state you live in, an aerated septic system is referred to by a variety of various names: Aerobic Treatment Unit (ATU), aeration system, septic aerator, advanced onsite treatment unit, and other terms are used to describe these devices.

The septic tank aerator is sometimes the sole moving item in the whole system.

As a result, you want to make certain that it is constantly working smoothly and that it is regularly maintained.

  1. What is a septic tank aerator and how does it work? An aerator, also known as an air pump, is a device that forces air and oxygen into your septic system. When there is an increased amount of oxygen available to natural bacteria in the system, this improves the amount of treatment that can be provided for nutrients in the effluent. Air is drawn into the tank by an aerator system from the outside and pumped through the tank by a pipe network and diffuser that are located inside the tank. What are the advantages of installing a septic aerator? There are several advantages to this system, including the fact that it can be used in homes with smaller lots, inadequate soil conditions, in areas where the water table is too high, and in homes located near a surface water body that is sensitive to contamination by nutrients contained in wastewater effluent. ATUs should be maintained on a regular basis during their service life. How difficult is it to keep a septic tank aeration system running? As with any onsite septic system, you will need to pump your tank every 3-5 years, as is standard practice. Always be cautious of what you put into a tank that has an aeration system
  2. The Think at the Sinkbrochure from the EPA SepticSmart program is a fantastic resource for guidance. As the moving parts of your aerator near the end of their service life, you will need to repair or replace them as necessary. Always use authentic manufacturer certified components for any repairs, as aftermarket parts may invalidate any warranties and may not be able to withstand the stresses placed on your system as a whole. If your aerator is of a certain size, the ambient temperature in your location, whether or not your in-tank diffusers require cleaning, and how your pump is installed will all influence how long it will last. Which HIBLOW air pump do I need for my septic system and how many do I need? Please check with the manufacturer of your overall treatment system to confirm that the air pump is the proper size for your particular unit. Another advantage of using a professional service provider is that they can help you select which HIBLOW pump type you require. Where can I get repair kits for my air pump? We have a large number of distributors around North America that can offer you with both pumps and repair parts. Contact one of our distributors now. Please contact us via email or phone to find out which location is the nearest or most convenient for you. Make certain that the items you are utilizing are genuine factory approved parts. When you use aftermarket components, the performance of your air pump may be affected, and it may not be able to achieve the pressures necessary for your system
See also:  How Much Weight Is Safe To Pull Over A Septic Tank? (Solution found)

Contact HIBLOW for Septic Aerators!

The use of ourHIBLOW aerators by wastewater treatment facilities for both residences and businesses can assist to ensure that only treated water is discharged back into the environment. “ Thank you very much, Mike, for your outstanding customer service and for recommending a reputable distribution company. I wasn’t sure what I needed, but the HP-60 aeration pump, diffuser, and sinking air line that I received have exceeded my expectations. Perfect!” Please get in touch with us right away for additional details!

Septic Tank Pumping

Septic tank pumping is a necessary maintenance operation that must be performed on a regular basis to guarantee that your system is operating effectively. It is the single most important thing you can do to guarantee that the components of your system operate correctly and that you get the most life possible out of the components in your system. The most common reason for parts and components to fail on an aerobic septic system is that the system is not being cleaned out on a regular basis as it should be.

It is also possible to be deceived by a working system into believing that nothing has to be done.

In actuality, if your system’s components are installed correctly and serviced on a regular basis, they should endure for many years.

In other words, we don’t merely pump your system till it’s completely empty and call it a day on the job.

When determining whether or not it is necessary to have your tank pumped, it is important to examine whether or not your tank is genuinely full.

Our crew is well-versed in identifying the differences, so if you’re unclear, don’t hesitate to contact us for assistance.

In order to guarantee that you receive a high-quality service, we recommend that you closely monitor whoever cleans your system to check that it is thoroughly cleaned and that all of the tanks that they claimed to have cleaned are indeed completely cleaned.

With Brighteyes, you can be assured that your faith in our firm will never be betrayed. 936-258-3080

Frequently Asked Service Questions : Norwalk Tank Company

What is the warranty on a new, Norweco © model 206C aerator and control panel?Effective September 1, 2009, a new Model 206C Aerator and control panel carry a three year warranty from date of installation.Warranty repair is accomplished by sending in the defective part to Norweco for their factory repair or replacement.The customer is responsible for the shipping charges.The Norweco 3 year Warranty may be downloaded at the Norwalk Tank website.Prior to September 1, 2009, all new and remanufactured aerators come with a two year warranty.Norweco Warranty
How often should Norweco Mechanical Tanks be pumped out? Periodically it is necessary to have the Norweco Mechanical Tank pumped out by a licensed septic pumper.This time frame varies according to occupancy and usage of the system.Our suggested standard is between 2-5 years.Our technicians will advise the customer if they feel it is necessary to have the tank pumped out because of the buildup of solids, sludge, and/or non-biodegradable material in the tank.Our 500 gallons per day tank has a total liquid capacity of 1300 gallons.This is pumped from the pretreatment compartment which may or may not be buried.If it is buried, it can be found up-stream from the aerator chamber in line with the inlet and approx. 12” below ground. The aeration chamber must also be pumped out and this is the chamber that contains your aerator.The aerator must be removed before pumping begins to prevent damage.
“I have an alarm going off in my basement, what do I do?”The two alarms Norwalk would be concerned with are the Norweco Control Box alarm and the Septronics High Water Alarm.All Norweco Mechanical Tanks will have a control panel but not all customers will have a high water alarm.The control panel will have a reset button on the front of the box and can be pushed to reset alarm.If that will not reset alarm (and stay off), a service visit needs to be scheduled to troubleshoot the cause for the alarm.If the High Water alarm is sounding, there may be a high water situation in the lift station.The customer should press the button marked, “Silence Horn” and a service visit should be scheduled.Heavy amounts of rain can cause your system to become saturated, slowing down the natural flow of your septic discharge.After heavy rain, the water in your mechanical tank may not leave quickly enough and this cause the alarm to sound.The best thing to do is to turn off your system at the control panel and let the ground take up the slack from the rain.After 1-2 days, turn your system back on and try to get the control panel to reset.If you still can not reset the system, then you should call Norwalk to have your system examined for other possible problems.
“What can or can’t (chemicals, home products, etc.) I use in connection with my Norweco septic system?”There are some chemicals, products, and substances, used in the normal household that can not be flushed down the drain of a household using a mechanical septic tank.Many of these substances have a detrimental effect on the organisms and the bio-kinetic process taking place in the tank and could do damage to the tank itself.Please see the “ Dos and Don’ts ” sheet available on thedownload pageof the Norwalk website.
“Why do I need a Maintenance contract and how do they work?”Illinois State law requires that all mechanical aeration septic systems be inspected and maintained a minimum of twice per year.If it is a surface discharge system (chlorine is added to the system), it should be inspected and filled 3 times per year.Norwalk offers yearly contracts for this type of maintenance in wide variety of levels depending upon the effluent demand on the system.With each home visit, the customer receives a full evaluation of the system, including cleaning of the aerator and shaft, checking the inlets and outlets of the tank, replacement of the bio-kinetic filter, cleaning and pumping of the chlorinator, and the filling of the chlorine contact tube.500 Gallon Per Day Contract
“Do I have a cavatette system?” or “What system do I have?”Many people call in and ask about their cavatette system.People will use the name cavatette as a generic term to describe all mechanical aeration systems.“Cavatette” is actually a very old brand name (no longer being produced).If you have a concrete cover that looks like a rectangle you may have an old Cavatette system.All Norweco systems can be distinguished by the round cover or covers on the openings of the tank chambers.Norweco tanks will have 1, 2, or 3 concrete covers, one of which will have a black vent cap molded directly into the cover.This cover should be on the chamber where the aerator is installed.If you have only one cover and it is vented, you have a Norweco 780 series tank.If you have one vented cover and one non-vented cover you have a 960 series tank installed before 1996 (the non-vented cover is over your bio-kinetic filter).If you have a non-vented cover up-stream(closer to house) from the aerator and a non-vented lid downstream(further from your house) from your aerator, the up-stream lid is covering your pre-treatment chamber.Diagrams and specifications of our Norweco brand tanks can be found on theHome Sewage Systemof our website.
“What damage is done if I don’t have a maintenance contract for a couple years?”First and foremost it isILLEGALin the state of Illinoisnotto have a maintenance contract on a mechanical aeration system.Second, by discharging raw sewage into our environment, you may be doing irreparable damage to your property, the property of your neighbor, and the local water table servicing your community.Finally by not maintaining your system properly, you can damage one or many components of your system.This damage can range from hundreds of dollars in repair to an aerator, to tens of thousands of dollars in damage to your tank, sand filter, and/or your septic field.A $200 yearly investment could save you a $20,000 cost in the future.
“How do I request a Service call?”If you are requesting your normal regular service visit, without any specific time needed, you can email your request [email protected] you have an alarm going off or you need a specific time and date, please call the Norwalk office at 815-726-3351 and ask for the Service Department.Specific time requests should be limited to 1st (8:00-8:30) appointment in the morning, AM only (8:00-12:00) appointment, or PM only (12:00-2:30) appointment.
“What kind of access do I need to leave for the service visit?”First, the service technicians needs free and open access to your system.This would include unlocking all gates and fences. Please keep family pets away from the system while it is being serviced.Also, please remove all planters, bird baths, and fountains off of the system covers before service.Second, landscaping needs to be planned in such a way as to have walk up access to the system.The components of your system that must be moved or replaced are very heavy and cumbersome, so landscaping around the tank needs to leave at least a 4 foot opening to your system.It becomes a safety hazard for our technicians if they have to lift system components up and over landscape materials.Also, please keep mulch and rock at least 6” below the top level of the covers.This material can fall into the system when lids are off and cause damage to system components subsequently causes expensive repairs.
“I received notice that I failed a health department effluent test.What do I do?”When you receive notice of a test failure, please contact Norwalk Tank and schedule a service visit.After that service, the health department will revisit your property and test your system again.Please note that Norwalk Tank can not request the health department to come out and retest.
“If I do not have a contract, can I still schedule a one-time service visit?”You may, at any time call and schedule a one-time service visit with Norwalk Tank service department.Please contact us for specific pricing that applies to these one-time services.The customer will be charged for the service visit, filter change, and any chlorine that is added to the system.The best value for our customers is to sign up for a yearly maintenance contract, with service visits, filter changes, and chlorine built right into the contract as well as other valuable services.
“What Maintenance Contract should I choose?”You need to choose the contract best suited for the needs of your system.If you system needs to have chlorine added to it, you need to chose between a Group 2, 3, or 4.Youmay notchoose group 1.If your system is an older system then it might be wise to choose a group with more emergency visits included in it.Also, if you have a large demand on your system (i.e., people in household, lots of laundry) you may want to upgrade to an upper group. Basically the differences between the groups are the number of regular visits, the number of emergency visits, and the amount of chlorine included in the contract.Also, the group 4 contract allows for in addition to 3 regular visits and 5 emergency visits, a 10% discount on all equipment purchases and a free loaner if your aerator has to be repaired.500 Gallon Per Day Contract

Leave a Comment

Your email address will not be published. Required fields are marked *