How To Lookup Septic Tank Location Oklahoma? (TOP 5 Tips)

  • Look for the septic tank map, if you have one. This is the easiest way to find where the septic tank is constructed in your property. This is usually a diagram that shows the precise location of the tank.

How much does a perc test cost in Oklahoma?

Perc testing typically costs $750 to $1,850 or $1,300 on average. On the high end, you might pay as much as $3,000 depending on local regulation and the size of the leach field or infiltration basin needed. A basic assessment costs $150 to $300 for a hand dug hole without specialized equipment.

Can I install my own septic system in Oklahoma?

The State of Oklahoma allows non-certified installers to install a limited number of systems. However, these installations must be inspected and approved by DEQ personnel before they are backfilled and/or made operational.

How much does a septic system cost in Oklahoma?

A typical 1,000-gallon tank installation for a 3-bedroom home ranges from $2,100 to $5,000. Materials cost between $600 and $2,500 without labor. A complete septic system, including a leach field, tank and piping costs $10,000 to $25,000. Installing a leach field costs $5,000 to $20,000, depending on the type.

How do I know what kind of septic tank I have?

Walk around your yard to look for a large bump in the grass on one side of the house. A sign that you have a septic system is a domed area under the grass. The size of the bump will vary depending on your house and the number of toilets you have, but it may be noticeable.

How do you know if land will perk?

Suitability can be determined through a perc or perk test, formally known as a Percolation Test. This test determines the rate at which water drains through the soil. If the property does not pass the perk test, than a standard septic system cannot by installed. There are alternatives, but they can be very expensive.

Are lagoons legal in Oklahoma?

Lagoon sizes in the southeastern counties of Oklahoma can be quite large due to the high rainfall and low evaporation rates. DEQ regulations do not allow lagoons to be constructed on tracts of land that are less than 2 ½ acres in size. Lagoon systems are comprised of a septic tank (1) and the lagoon (2).

How do I get a license to drive a septic system in Oklahoma?

How Do Septic Tank Installers Apply for Certification in Oklahoma?

  1. Step 1 – Meet the Experience Requirements.
  2. Step 2 – Purchase a Surety Bond.
  3. Step 3 – Complete the Application.
  4. Step 4 – Complete the Certification Course(s)
  5. Step 5 – Pass the Exam(s)

How long are perc tests good for?

How long is a perc test good for? An Improvement Permit/Construction Authorization issued by a Local Health Department is valid for 5 years.

Can you have a septic tank without a leach field?

The waste from most septic tanks flows to a soakaway system or a drainage field. If your septic tank doesn’t have a drainage field or soakaway system, the waste water will instead flow through a sealed pipe and empty straight into a ditch or a local water course.

What are the 3 types of septic systems?

Types of Septic Systems

  • Septic Tank.
  • Conventional System.
  • Chamber System.
  • Drip Distribution System.
  • Aerobic Treatment Unit.
  • Mound Systems.
  • Recirculating Sand Filter System.
  • Evapotranspiration System.

What is the cheapest septic system?

Conventional septic system These conventional septic systems are usually the most affordable, with an average cost of around $3,000.

How do I know if my house has a septic tank?

A surefire way to confirm whether or not your home has a septic system is to check your property records. It is likely that the building permit and blueprints for your home and property will contain information about the presence (or lack) of a septic tank.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

Will metal detector find septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

Document Search

07-15-20_MS4 Evaluation Update July 15, 2020
1. Regulatory OverviewWaste Determination May 15, 2019
10 Simple Steps to Improve Air Quality May 6, 2021
2_okr04_permit_overview_outreach_2015 January 28, 2019
2. Container Management May 15, 2019
2003 Tar Creek Study March 19, 2019
2006 IFR Conversion Guidelines March 6, 2019
2007 Tar Creek Study March 19, 2019
2010dwsrfiup January 29, 2019
2011 Tulsa MS4 Fact Sheet May 2, 2019
2011 Tulsa MS4 Permit May 2, 2019
2011 Tulsa MS4 Permit Response To Comments May 2, 2019
2012 Continuing Planning Process April 30, 2019
2012 OKC MS4 Fact Sheet May 2, 2019
2012 OKC MS4 Permit May 2, 2019
2012 OKC MS4 Permit Response To Comments May 2, 2019
2012 OKG38 Fact Sheet May 1, 2019
2012 OKG38 General Permit to Discharge Filter Backwash Wastewater May 1, 2019
2012-OKG38-fact-sheet May 22, 2018
2012-OKG38-Permit May 22, 2018
2012constructionokr10publicnotice January 28, 2019
2012okcms4permit_final_feb2013 January 28, 2019
2012okcms4permit_final_feb2013 January 29, 2019
2013-04-Pharmaceutical_Waste_Position_Paper-Board_Approved September 23, 2019
2014-Approval-Letter-and-Decision-Document.pdf January 25, 2019
2015 OKG59 General Permit to Discharge Splashpad Wastewater May 1, 2019
2015 OKR04 Fact Sheet May 2, 2019
2015 OKR04 General Permit May 2, 2019
2015 OKR04 General Permit Response To Comments May 2, 2019
2015 OKR04 Notice of Intent (NOI) May 2, 2019
2015 OKR04 Notice of Termination (NOT) May 2, 2019
2016 DEQ Annual Report September 20, 2019
2016 Gov_FD March 11, 2019
2016 Integrated Report – Report Only April 22, 2019
2016 OKG58 General Permit to Discharge Lagoon Wastewater and Fact Sheet (2018 modification) May 1, 2019
2016-2020_Annual_Tonnage_Reported March 17, 2021
2016-Public-Notice.pdf January 25, 2019
2017 DEQ Annual Report September 20, 2019
2017 OKR05 Annual Compliance Report (ACSCER) May 3, 2019
2017 OKR05 DEQ Industrial SWP3 Template May 3, 2019
2017 OKR05 Fact Sheet May 3, 2019
2017 OKR05 General Permit May 3, 2019
2017 OKR05 General Permit Response To Comments May 3, 2019
2017 OKR05 Inspections and Enforcement Slides May 3, 2019
2017 OKR05 NEC, SWP3, and NOI Slides May 3, 2019
2017 OKR05 No Exposure Certification (NEC) May 3, 2019
2017 OKR05 Notice of Intent (NOI) May 3, 2019
2017 OKR05 Permit Overview Slides May 3, 2019
2017 OKR10 Fact Sheet May 1, 2019
2017 OKR10 General Permit for Construction Stormwater May 1, 2019
2017 OKR10 Inspections May 2, 2019
2017 OKR10 Permit Administration May 2, 2019
2017 OKR10 Permit Overview May 2, 2019
2017 OKR10 Workshop Agenda May 2, 2019
2017 OKR10 Workshop Intro May 2, 2019
2017_MercuryinFish July 19, 2018
2017Dec_Revised Section 10 September 23, 2019
2018 DEQ Annual Report September 20, 2019
2019 Annual Report September 9, 2020
2019-20 Fee Schedule June 28, 2019
2019-2020 Tag Grant Judging Rubric October 8, 2019
2019AnnualAnnouncementIndustrialRadiographers February 12, 2019
2020 Annual Report November 4, 2020
2020_CleanCommunity_Application January 22, 2021
2020GPRAListandStatus September 23, 2019
2021 Annual Report November 4, 2021
2021 Mercury Booklet September 1, 2021
2021 Worksheets for Calculating Closure/Post-Closure Cost Estimates February 2, 2021
2021_RMAC_Agenda August 4, 2021
2021.7.6-Lead-in-Schools-Sample-Results-Erick-Elementary-School-Report July 8, 2021
2021.7.6-Lead-in-Schools-Sample-Results-Erick-Junior-High-School-Report July 8, 2021
2021.7.6-Lead-in-Schools-Sample-Results-Mullhall-Orlando-High-School-Report July 8, 2021
205-001 (HW Inspection Record 2006) May 16, 2019
205-004 (CESQG 2006) May 16, 2019
205-006 (TSD General 2006) May 16, 2019
205-007 (Tank 2006) September 23, 2019
205-008 (TSD Landfill 2006) May 16, 2019
205-009 (Drip Pad 2006) May 16, 2019
205-010 (Containment Building 2006) May 16, 2019
205-011 (TSD Groundwater Monitoring 2006) May 16, 2019
210-NRI_FINAL_19-07-26 September 20, 2019
210-RIS_FINAL_19-09-17 September 20, 2019
252:004 Rules of Practice and Procedure September 13, 2021
252:020 Emergency Planning and Community Right-to-Know April 2, 2019
252:020 Tier II Fees April 2, 2019
252:100 Air Pollution Control September 13, 2021
252:110 Lead-Based Paint Management September 13, 2021
252:205 Hazardous Waste Management September 13, 2021
252:205 Hazardous Waste Management Fees June 19, 2019
252:210 Highway Spill Remediation June 19, 2019
252:210 Highway Spill Remediation Draft September 23, 2019
252:210 Highway Spill Remediation Fees July 27, 2021
252:221 Brownfields April 3, 2019
252:301 Laboratory Accreditation September 13, 2019
252:301 Laboratory Accreditation Fees September 17, 2019
252:302 Field Laboratory Accreditation September 13, 2019
252:302 Field Laboratory Accreditation Fees September 17, 2019
252:305 Laboratory Services April 3, 2019
252:307 TNI Laboratory Accreditation September 13, 2019
252:307 TNI Laboratory Analytical Fees September 17, 2019

On-site Sewage Treatment

Individual and small public on-site wastewater treatment systems are used by rural Oklahoma households and businesses, as defined in Chapter 252:641, Individual and Small Public On-Site Sewage Treatment System. Typical on-site systems include a 1000-gallon septic tank with a dispersion field (a network of trenches filled with pipe and gravel), aerobic treatment units with spray or drip irrigation, low-pressure dosing systems, and lagoons. It is necessary to have a soil test completed on your land before you can begin developing or selecting an on-site system for your new house or company.

In accordance with the findings of your soil test, the size of your land, and the number of bedrooms in your home, an on-site sewage treatment system (or systems) is created for you.

  • The DEQ Soil Test and a list of DEQ Certified Soil Profilers may both be requested by visiting this website.
  • Before beginning the installation process, the installer must get an Authorization to Construct an On-site Sewage Treatment System.
  • Systems that are not conventional Maintenance Services that have been requested Forms On-site sewage systems are complex systems, and the design and installation of one is reliant on a number of variables.
  • In some cases, a system outlined in our guidelines cannot be built, and a different on-site system is required in these situations.
  • Additional information on alternative systems, as well as the application and approval procedure for alternative systems, can be obtained by contacting your local DEQ agent or by calling (405)702-6100.
  • The majority of the time, though, the on-site technology is implemented and then forgotten about.
  • The sort of maintenance and the frequency with which it is necessary for your on-site system are determined by the type of system.
  • The following sections provide descriptions of the many types of on-site systems.
  • If you are still confused about the sort of system you have after reading the descriptions below, you can call the local DEQ office for assistance at (405)702-6100 for more clarification.
  • Soil profiles, final inspections, well assessments, existing system inspections, and authorizations or licenses for the construction of an on-site sewage treatment system are all examples of the services offered.

The following methods of payment are accepted: check, money order, or online using a Visa, Mastercard, or debit card. If you are paying with a check or money order, you must submit the completed Request for Services Form to the address on the form in order to get service.

Online Payments

The use of on-site wastewater systems in rural Oklahoma residences and businesses is outlined in Chapter 252:641, Individual and Small Public On-Site Sewage Treatment System, of the Oklahoma Code of Regulations. On-site systems include traditional systems, which comprise of a 1000-gallon septic tank and a dispersion field (a network of trenches filled with pipe and gravel), aerobic treatment units with spray or drip irrigation, low-pressure dosing systems, and lagoon systems, among other things.

  • The qualities of the soil on your land are determined by the soil test.
  • A soil test can be performed by the Department of Environmental Quality, or you can hire a DEQ Certified Soil Profiler to do the testing for you.
  • After that, you’ll need to employ an experienced contractor to put in the sewage treatment system on your premises.
  • A DEQ Certified Installer click here or the Department of Environmental Quality must examine all on-site sewage treatment systems before they may be used.
  • Size and form of the lot, the size of the house, and the findings of the soil test are all important considerations.
  • In order for a system to be installed, the DEQ must authorize any alternative systems.
  • It is possible to have a cost-effective and environmentally friendly treatment system if the system is correctly planned, built, and maintained on site.
  • In order to avoid costly system failures as well as pricey repairs, homeowners must perform regular maintenance on their systems.
  • For this reason, knowing what sort of system serves your house or company is the first step in system maintenance.
  • To learn more about individual maintenance items, select the system type from the drop-down menu.

Système de traitement subsurface des eaux usées Treatment System for the Lagoon Treatment System for Evapotranspiration and Absorption a system for aerobic waste removal Citizens of Oklahoma can obtain desired services from the Environmental Complaints and Local Services Division (ECLS), which presently operates 22 local offices around the state.

When our Environmental Specialists execute the services listed above, we charge standardized rates specified by the Department of the Environment (DEQ).

Online payments using a Visa, Mastercard, or debit card are accepted in addition to checks and money orders. Upon completion of the Request for Services Form and submission of payment by check or money order, the completed form must be mailed to the address shown on the form.

Basic Septic System Rules for Oklahoma – Oklahoma State University

Submitted by Sergio M. Abit Jr. and Emily Hollarn Several of us are interested in building or purchasing homes in the country for a number of reasons. It is possible to be closer to nature by living outside of city limits. It is also possible to cultivate vegetables and raise farm animals, and it is possible to live a simple and calm life in a rural environment by living outside of city limits. One thing to keep in mind is that, while living in the country has many advantages, access to the comforts that towns offer is not always available, especially in rural areas.

  1. The latter requires the installation of an on-site wastewater treatment system, which is more frequently known as a septic system.
  2. This information sheet outlines the requirements that must be followed while obtaining an installation permit, complying with site and soil limits, and installing and maintaining septic systems.
  3. PSS-2914, Keep Your Septic System in Good Working Order, and PSS-2913, On-site Wastewater Treatment Systems Permitted in Oklahoma are two of the state’s most important standards.
  4. Much of this information sheet is prepared in a simplified question and answer style, however there are certain sections that have been taken practically literally from the Code of Federal Regulations.
See also:  How Do I Find Out What Kind Of Septic Tank I Have?

Site Requirements and Restrictions

Is there a minimum lot size requirement for building a home? With the usage of public water (such as that provided by the city or the rural water district), a minimum lot size of 12 acres is required for the majority of septic systems for a residence that will require one. The use of an individual drinking water well necessitates the usage of a minimum lot size of 344 acres for the majority of systems. What is the definition of a “repair area” requirement? Aside from the space set up for septic system installation, an adequate amount of space should be set aside for repair work.

  • When purchasing a home, inquire as to the location of the authorized repair area.
  • Where is the best location for the septic system to be installed?
  • Keep in mind that there are minimum separation distances between items such as water wells, property boundaries, and buildings, as well as other restrictions to follow when driving.
  • Water Body Protection Places (WBPAs) are those areas that are located within 1,320 feet of water bodies (such as rivers and lakes) that have been identified by the state as being specifically protected against pollution and are classified as such.
  • This indicates that the cost of the septic system in that location will be higher.
  • However, it is important to remember that the requirement for a nitrate-reduction component applies only to new homes or modifications to an existing home’s septic system.
  • It is recommended that at least 10,000 square feet be set aside for the septic system in the region where it will be constructed, but this is not a requirement as a general rule.

The exact amount of the area required for the septic system will initially be determined by the soil and site characteristics of the surrounding region.

The number of bedrooms in the house is taken into consideration once the proper septic system has been selected in order to estimate the real size of the space that must be given for the septic system.

Generally speaking, the more bedrooms in a house and the finer the soil texture in the surrounding region (i.e., the more clay in the soil), the more space is required for a septic system to be installed.

As previously said, the soil and site qualities influence the type of septic system that may be installed as well as the amount of the land space that is required for the installation.

What type of soil testing will be required?

When the results of a percolation test are obtained, they may be used to determine the rate of subsurface water flow at depths where residential wastewater is typically applied.

Either test might be used as a starting point for making judgments about a septic system.

It should also be noted that if the test done is a soil profile description, the amount of land required for the septic system is typically less.

When the choice has already been taken to establish a lagoon system or an aerobic treatment system with spray irrigation, a soil test is no longer necessary, since the system is already in place.

Soil profile descriptions may only be performed by soil profilers who have received state certification.

Testing for percolation can be carried out by professional engineers, certified sanitarians, environmental specialists, or soil scientists.

A note on soil testing: Some communities in Oklahoma require a soil test result before approving a construction permit application.

Permits

What is it that requires a permit? Septic system installations, including the addition of an extra system, on a property must be approved by the local building department prior to proceeding. Permits are also required for modifications to an existing system. It is possible that septic system improvements will be required as a result of the following: a) Septic systems that are not working properly, b) home renovations that result in an increase in the number of beds, c) an increase in water consumption as a result of a change in the usage of a house or building, and d) the movement of any component of a septic system.

Where can I acquire an installation or modification permit, and how do I get one?

To submit an application for a permit, go to DEQ Applications or contact your local DEQ office for help.

Often, the installer will take care of the paperwork for you, including the installation or modification permission application.

Inspections

Inspections are carried out by whom, and when are they necessary? There are two situations in which an inspection by DEQ officials is required. They are as follows: The following are examples of non-certified installations: 1) repairs and system changes made by a non-certified installer; and 2) installation of new systems performed by a non-certified installer Prior to backfilling and/or placing the system into operation, the inspection must be completed to ensure that the installation, modification, or repairs are of satisfactory quality.

The fact that a state-certified installer performs the installation, alteration, or repair eliminates the requirement for DEQ employees to conduct an inspection because qualified installers are permitted to do self-inspection is worth mentioning.

The installer is responsible for notifying the DEQ of any needed inspections relating to an installation, alteration, or repair that may be required.

Installation

Inspections are carried out by whom and when they are required. There are two situations in which an inspection by DEQ officials is required. 1. You will find them as follows: 1) Repairs and system changes made by a non-certified installer; and 2) installation of new systems performed by a non-certified installer are all examples of non-certified installation. Prior to backfilling and/or placing the system into operation, the inspection must be carried out to ensure that the installation, modification, or repairs were completed correctly.

Who is in charge of setting up a DEQ inspection visit?

The installer is responsible for notifying the DEQ of any needed inspections relating to an installation, alteration, or repair that may be necessary. Department of Environmental Quality (DEQ) officials will be in charge of inspecting in response to complaints.

Responsibilities of the Owner

Septic systems that are properly maintained will remove dangerous contaminants from home water. Owners, their neighbors, and the environment are all at risk if their systems are not properly maintained and operated. In plain language, the rule mandates that the owner of a system be responsible for ensuring that the system is properly maintained and operated so that: 1) sewage or effluent from the system is properly treated and does not surface, pool, flow across the ground, or worse, discharge to surface waters, 2) all components of the system (including lagoons) are maintained and do not leak or overflow, and 3) the necessary security measures are in place (e.g.

  1. required fences are intact, septic tank lids are intact and properly secured).
  2. Civil and criminal fines may be imposed for violations and carelessness.
  3. Abit Jr., Ph.D., is a researcher at the University of California, Berkeley.
  4. Ms.
Was this information helpful?
Oklahoma – Statewide

Free Search Environmental Services and ContractorsView Oklahoma environmental services including certified installers, septic system pumpers and transporters including online complaint form.
Free Search Restaurant InspectionsSearch Oklahoma restaurant inspection reports by county or name.
Cleveland County

Free Search City of Moore Codes and OrdinancesView the City of Moore municipal code, rules, regulations, and land development code.
Free Search City of Norman Building Permit ReportsView City of Norman building permit online inspections including scheduling by application number, applications fees, address, parcel number or name.
Oklahoma County

Free Search City of Edmond Building PermitsView City of Edmond information and requirements about building permits including monthly building permit reports.
Free Search Regulations and Land Use Map View Oklahoma County development regulations and land use plan map including registration fees.
Tulsa County

Free Search City of Broken Arrow Permit InspectionsSchedule City of Broken Arrow permit inspections online.
Free Search City of Tulsa PermitsSearch City of Tulsa permit records including address search.

Where’s my septic tank?

There are a few solutions available if the previous homeowner failed to supply this critical information or if you have misplaced your original copy:

  • Your local DHEC office may have a copy of your building permit on file if your house was built within the last five years or fewer, according to the DHEC. A copy of a septic tank permit can be obtained from the local office by any individual or group, regardless of whether or not they own the land in question. Because of this, it is highly recommended that you have as much of the following information as possible ready at the time of your request.
  • Your local DHEC office may have a copy of your building permit on file if your home was constructed within the last five years or less, according to the DHEC. A copy of a septic tank permit can be obtained from the local office by any individual or group, regardless of whether they own the land. If you have as much of the following information as possible ready at the time of your request, the search process will go much more quickly:
  • You may also submit a request for a copy of the permission through our Freedom of Information office, although this is not mandatory. To obtain a copy through the Freedom of Information Office, please complete and submit a copy of the DHEC FOI form. Instructions are given with the application. If feasible, please include the information about the property that is stated above. When looking around your yard, search for manhole covers or lids that have been buried by grass or leaves if your house was constructed before 1990.

Tags

Septic Tank Alerts Septic Tank Alerts

Looking for Your Septic Tank? Here’s How to Find It

“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.

Why you need to know where your septic tank is located

If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.

In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.

How to find your septic tank

  1. Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
  2. Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.

After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank.

When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.

  • The post was published on July 16, 2019 under the category Septic Tank System.
See also:  What To Expect When You Have A Septic Tank? (Perfect answer)

How To Find My Septic Tank

  1. What is a septic tank
  2. How do I know if I have a septic tank
  3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
  4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

  1. “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
  2. When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
  3. The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
  4. In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

  1. A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
  2. A septic system is likely to be installed in your home if you reside in a rather rural location.
  3. Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
  4. When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
  5. Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

  • If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
  • The county health department is responsible for keeping track of septic systems.
  • A septic tank’s position could be depicted on a survey map, for example.
  • The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

  • In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
  • By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
  • The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
  • Going via the sewage line itself is another method of locating the septic tank utilizing it.
  • Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
  • When the snake comes to a complete halt, it has almost certainly reached the tank.
  • While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
  • When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

  • Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
  • Directly in front of the home Immediately adjacent to your well (if you have one)
  • In close proximity to trees or densely planted regions
  • In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

See also:  What To Do If Outlet Baffle Breaks Off Older Concrete Septic Tank? (Question)

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Putting up a large sign in your yard saying “Septic Tank Here!” is probably not a good idea, but leaving some sort of marker will allow you to locate the tank and lid quickly if you need them in the future. A good yard marker should be sturdy enough that it does not blow away in the wind and cannot be readily moved by youngsters who are running around in the yard. Pavers on the patio, potted plants, and ornamental gnomes or rocks are just a few of the possibilities. Additionally, in addition to installing a physical sign near the septic tank, you may build a map or diagram illustrating the tank’s position.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job

Septic Systems in Oklahoma

Ownership of a septic system is widespread among homeowners in Oklahoma’s small towns and rural regions, according to the state’s Department of Agriculture. As a result, a variety of standards and laws have been established to strictly control the construction and maintenance of private septic systems in order to maintain the health of the state’s land and water.

Regulation of Septic Tank Systems

For private residences and public utilities, the Department of Environmental Quality (DEQ) is the regulatory authority responsible for the treatment of sewage and associated concerns. Their rules are intended to avoid the contamination of streams and groundwater sources as a result of sewage contamination.

Licensure Requirements for Septic System Contractors

The Department of Environmental Quality (DEQ) offers licenses to installers and contractors of sewage systems in accordance with Title 252, Chapter 645 of the Oklahoma Administrative Code. They also have laws to regulate the pumping, transporting, and disposal of sewage, which necessitates the operator obtaining a yearly license from the Department of Environmental Quality (DEQ).

Vehicles utilized for the purposes of pumping, carrying, or disposing of sewage must also be inspected and registered with the DEQ on a yearly basis, according to the regulations.

Installing a New Septic System

Homeowners must submit an application to the Department of Environmental Quality (DEQ) for a permit to establish a private onsite sewage system on their property using a prescribed application form. It is necessary to give soil testing findings as well as schematics showing the exact position of water sources in relation to buildings and other water sources. A permit to construct a sewage system will be issued if the soil has been determined to be suitable for the purpose of construction. The inspection and approval of new installations by a qualified installer or DEQ official is necessary prior to providing authorization for them to be used.

How to File a Complaint

Environmental concerns can be lodged by calling the Complaint Hotline at 1-800-522-0206, which is available 24 hours a day, seven days a week, or by submitting an online complaint form. The following page contains contact information for local DEQ offices.

Oklahoma Septic Tank Installer Bond: A Comprehensive Guide

This guide includes information for insurance agents to assist contractors in obtaining Oklahoma Septic Tank Certified Installer bonds and other related insurance products.

At a Glance:

  • The average annual cost is $100. The amount of the bond is $10,000. Everyone and any firm wishing to earn a Septic Tank Installer Certification in the State of Oklahoma is required to have this certification. The purpose of this regulation is to ensure that the general public will be compensated for any losses sustained if a septic tank installation fails to comply with certification regulations. Septic tank installers in Oklahoma are regulated by the Oklahoma Department of Environmental Quality (DEQ).

Background

Oklahoma statute59-30-1158requires all septic tank installers who do business in the state to be certified by the Department of Environmental Quality. The certification laws and regulations were created by the Oklahoma government in order to guarantee that installers conduct themselves in an ethical manner. Installers must acquire and maintain a $10,000 septic tank certified installersurety bond in order to be eligible to get a certification. This is done in order to provide financial security for the enforcement of the certification statute.

What is the Purpose of the Oklahoma Septic Tank Certified Installer Bond?

In order to be certified as a septic tank installation in Oklahoma, septic tank installers must acquire a Septic Tank Installer Bond as part of the application procedure. The bond may be purchased online. If the installation fails to comply with the certification standards, the bond assures that the general public will be compensated for any financial loss they have suffered. Shortly put, a bond is a sort of insurance that protects the general public in the event that a contractor violates certification regulations.

How Can an Insurance Agent Obtain an Oklahoma Septic Tank Installer Surety Bond?

The process of acquiring an Oklahoma Septic Tank Certified Installer Bond is simplified using BondExchange. Simply log into your account and perform a keyword search to locate the “contractor” bond in our database by entering “contractor” in the search box. Don’t have a login? Click here. Enroll today and let us assist you in meeting the demands of your clients. Our knowledgeable underwriting staff is ready to assist you by phone (800) 438-1162, email, or live chat from 7:30 a.m. to 7:00 p.m.

Our 40 years of expertise, cutting-edge technology, and access to global markets means that BondExchange has the knowledge and resources to give your clients with fast and polite service, whether they are receiving bids or issuing bonds.

Is a Credit Check Required for the Oklahoma Septic Tank Installer Bond?

The Oklahoma Septic Tank Certified Installer Bond does not need a credit check, and there is no credit check requirement.

This bond is deemed low-risk, and as a result, the same cheap rate is issued to all septic tank installations throughout the state of Oklahoma.

How Much Does the Oklahoma Septic Tank Certified Installer Bond Cost?

The $10,000 Oklahoma Septic Tank Certified Installer Bond is just $100 per year, which is a significant savings.

How Does Oklahoma Define “Septic Tank Installer”?

Septic tank installers are defined by the Oklahoma Department of Environmental Quality as anyone or any corporate entity who installs ten or more onsite sewage systems per year.

How Do Septic Tank Installers Apply for Certification in Oklahoma?

Septic tank installers in Oklahoma must go through a series of stages in order to obtain their accreditation. Detailed instructions on how to become certified are provided here, however installers should consult to the DEQ’s Certification Page for further information. Validity of the Certification – The Oklahoma Septic Tank Installer Certification is valid for one year and must be renewed before it expires.

Step 1 – Meet the Experience Requirements

Individuals who wish to be considered for the septic tank installation certification must have successfully built at least five on site sewage treatment systems within the two-year period preceding the submission of their application. In order to be accepted on the initial inspection, applicants must have had at least 90% of systems installed during the previous year approved. Applicants are required to submit paperwork that verifies their installations in conjunction with their application.

Step 2 – Purchase a Surety Bond

The acquisition and maintenance of a $10,000 Septic Tank Certified Installer surety bond are required of septic tank installers.

Step 3 – Complete the Application

The Oklahoma Department of Environmental QualityAccounts ReceivablePO Box 2036Oklahoma City, OK 73101-2036 should receive all septic tank installation regulatory certificate applications. Contractors that build septic tanks must complete the application, which includes the following steps: Affidavit of Citizenship and Immigration Status– Installers are required to provide anAffidavit of Citizenship and Immigration Status with their application. 3.b Fees– Installers are needed to submit a $227.03 application fee as well as a $178.28 test cost for each exam the installation intends to complete before they can be certified (more on this topic below)

Step 4 – Complete the Certification Course(s)

Applicants for the Septic Tank Installer Certification must finish a certification course for each examination they choose to take before they can sit for the examination. The schedule for all of the septic tank installation certification classes may be found by clicking here. To register for courses, applicants should contact the Department of Environmental Quality.

Step 5 – Pass the Exam(s)

Septic tank installers who have successfully completed their certification course(s) are eligible to sit for the septic tank installer certification examination (s). The following are the several examinations that septic tank installers may be required to take:

  • CSE, Aerobic with Drip Irrigation, Aerobic with Spray, Lagoon, Low Pressure Dosing (LPD), and other methods are used.

How Does an Oklahoma Septic Tank Installer Renew Their Certification?

CSE, Aerobic with Drip Irrigation, Aerobic with Spray, Lagoon, Low Pressure Dosing (LPD), and other terms and concepts.

What Are the Insurance Requirements for the Oklahoma Septic Tank Installer Certification?

There is no requirement in the state of Oklahoma for licensed septic tank installers to have any type of liability insurance coverage. Septic tank installers who are certified will be required to buy and maintain a $10,000 surety bond.

How Do Oklahoma Septic Tank Installers File Their Bond With The Oklahoma DEQ?

Septic tank installers should submit the completed bond form, together with the power of attorney, to the following address: Septic Tank Installers Oklahoma Department of Environmental QualityAccounts ReceivablePO Box 2036Oklahoma City, OK 73101-2036 Oklahoma Department of Environmental QualityAccounts ReceivablePO Box 2036Oklahoma City, OK 73101-2036 The surety bond for a septic tank certified installer must be signed by both the surety business that issued the bond and the installer in order for it to be valid.

The bond form should contain the following information, which should be provided by the surety company:

  • The date on which the bond becomes effective
  • The date on which the bond expires
  • The legal name of the company or individual(s) who is purchasing the bond.

What Can Septic Tank Installers Do to Avoid Claims Against the Oklahoma Septic Tank Certified Installer Bond?

Installers must adhere to all certificate restrictions in the state in order to avoid claims on the Septic Tank Installer Bond, including some of the most serious concerns listed below that are known to produce claims on the bond:

  • Install all onsite sewage facilities in a proper manner. Any systems that have been poorly installed should be repaired or replaced.

What Other Insurance Products Can Agents Offer Certified Septic Tank Installers in Oklahoma?

The state of Oklahoma does not require licensed septic tank installers to have any type of general liability insurance coverage. Many installers, on the other hand, will want to secure this insurance regardless of the circumstances. Because bonds are our sole line of business at BondExchange, we do not provide liability insurance; nonetheless, our agents frequently rely on third-party brokers to handle this particular area of business. You may see a list of brokers who operate in this market by clicking here.

How Can Insurance Agents Prospect for Oklahoma Certified Septic Tank Installer Customers?

Oklahoma has a user-friendly public database that allows you to search for current septic tank installers in the state. The database may be accessed at this link. For further marketing tools, please contact BondExchange. Agents can also take advantage of our print-mail partnerships to receive discounts on mailing services for their clients.

What other Contractor License Bonds are Required in Oklahoma?

Contractors in Oklahoma will be required to get certain bonds that correspond to the kind of license that they hold. The following are all of the many types of contractor license bonds that the State of Oklahoma requires:

  • A $5,000 bond limit is set for electrical contractors, $5,000 for mechanical contractors, $10,000 for plumbing contractors, and $10,000 for soil profiling contractors.

Leave a Comment

Your email address will not be published. Required fields are marked *