How Much Sludge Should Be In The Bottom Of A Septic Tank? (Question)

Essentially, while the shapes and designs of septic tanks will always vary the world over, you should ensure that your tank is never more than 30% sludge layer. If your tank capacity is at 30% sludge or more, then it is likely time to start pumping it out!

What is Scum in a septic tank?

Scum: Scum refers to the set of substances in a septic tank which are lighter than water. It usually consists of oil, fats, and grease. These substances float to the top, above the water where the aerobic bacteria work to digest a majority of the floating solid waste materials.

How much sludge is normal in a septic tank?

A septic tank should always be “filled” to its normal liquid level, or the bottom of the outlet pipe which carries effluent to the absorption area. This normal liquid level is usually between 8” to 12” from the top of the tank on average (see picture at right).

How thick should the sludge layer be in a septic tank?

Septic tanks need to be pumped out when the sludge layer exceeds 24 inches in depth or when the bottom of the scum layer is less than 3 inches above the Page 2 lower end of the submerged outlet. If you cannot locate the submerged outlet, clean the tank if the scum layer is more than 12 inches thick.

How thick should the crust be in a septic tank?

Normal sludge depth is one to four inches. If greater, or if less than 10 inches of water above the top of the sludge exists, check with a service contractor about a pump out. If there is a solid, thick (over one inch) crust on the top, it should be pumped out with the rest of the tank contents.

How do you get rid of septic sludge?

How to Reduce Sludge in a Septic Tank Without Pumping

Install an aeration system with diffused air in your septic tank.

Break up any compacted sludge.
Add a bio-activator or microbe blend.
Maintain the aeration system.

Add additional Microbes as required.

How do I check my septic tank sludge level?

To measure the sludge layer:

Slowly lower the tube into the septic tank until it touches the bottom of the tank.

As the device is slowly pulled out of the water, the check valve closes capturing a liquid/solid profile of the septic tank water. The thickness of the sludge layer can be measured.

How do you know if your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

Your Drains Are Taking Forever.

Standing Water Over Your Septic Tank.
Bad Smells Coming From Your Yard.
You Hear Gurgling Water.

You Have A Sewage Backup.
How often should you empty your septic tank?

Why is there sludge in my septic tank?

Septic sludge is normal for any septic tank. The aerobic bacteria aren’t able to decompose every solid waste that enters the system. This leads to layers of sludge on the tank floor. Septic waste clogging the drain field prevents water from draining into the soil and filtering naturally.

Do muck munchers work in a septic tank?

Yes, you can use Muck Munchers with all types of Package Sewage Treatment Units. Whether you have an old traditional brick-built septic tank or a modern package sewage treatment unit or bio-filter, Muck Munchers is the perfect alternative to more frequent cleaning and emptying.

How do you prevent fat build up in a septic tank?

Using a grease trap additive, such as the liquid or powder form of Bio-Secure Grease Trap Concentrate, can help prevent septic tanks, grease tanks, and sewer lines from clogging. It is relatively easy to use. Just mix the power or liquid additive with warm water and rinse it down the drain.

What eats sludge in septic tank?

One example of a homemade remedy is to flush ¼-½ a cup of instant yeast down your toilet. The yeast eats away at the sludge and helps loosen it, breaking it down so that wastewater can get through.

Sludge 101

Inquiry:I am new to the field of pumping and am intrigued by the biological activities that take place in each specific sewage treatment system. Despite the fact that I have a slew of questions, I will only submit one: I’d want to know exactly what sludge is. According to one online source, sludge is comprised of sewage particles that swiftly sink through the surface scum. According to another source, sludge is a waste product produced by enzymes when they are performing their decomposition function on waste material.

If so, is this a contributing factor to drainfield glazing?

Sludge is a term that can be applied to any substance that has settled as a result of bacterial or yeast activity, without qualification.

In a municipal sewage treatment system, the majority of the bacterial activity is aerobic in nature.

This sludge has a composition that is similar to that of soil.
As a result, the “sludge” consisted primarily of organic debris with a small amount of nitrogen added.

Consequently, I’ll go over septic tank sludge with you.
Anaerobic bacteria steadily breakdown the solids, resulting in a reduction in their volume over time.
Due to the rise in the sludge layer, there is a reduction in the amount of liquid in the septic tank, and some particles may pass through the tank and into the soil absorption system.

You must inform your consumers about the current circumstances in this regard.
When bones and coffee grounds are thrown into the garbage disposal, they contribute to the sludge layer since they do not decompose due to bacterial action.

Home sewerage is likely to contain soap or detergent residues in addition to the sewage.

Cooking oils and fats float as well, becoming part of the scum layer as a result.

In addition, the scum layer takes up a portion of the liquid volume in the septic tank.

Before this can occur, the septic tank must be thoroughly cleansed and emptied out of the ground.

A settling tank is often installed in the sewage line before to the aerobic tank, according to the design.

The aerobic activity in the second tank is more effective in decomposing organic solids, but a residue in the aerobic tank must be removed on a regular basis.

Unless any of the sludges I’ve described are allowed to dry out, it will be impossible to separate and check any small particles, in my view.

Organic matter and nutrients are added by the sludge, which is then recycled to help plants develop.

Ideally, there should be little, if any, sludge or scum pouring out into the soil absorption area if the septic tank is properly maintained and cleaned on a regular basis.

The biomat is formed as a result of the presence of suspended organic particles in the effluent from the septic tank.

On the trench side, the biomat is anaerobic, whereas on the soil side, it is aerobic.

The biomat is designed to enable fluids to pass through it.

A biomat will always form in a soil absorption system because of the nature of the soil.

The pace of decomposition is determined by the texture of the soil.

Onsite sewage treatment maintenance is critical to the proper running of an onsite sewage treatment system in order for it to remain operational. This is the message you need to communicate to your consumers in the strongest possible terms.

How Often Should A Septic Tank Be Pumped?

Rural residents frequently inquire as to how frequently they should have their septic tanks drained. Unfortunately, we are unable to provide them with a number or formula because everything is dependent. The frequency with which the tank must be pumped will be determined by the size of the tank and the amount of solids that are dumped into it. Tanks with greater capacity will require fewer pumpings in less time than tanks of lesser capacity. More significantly, if the amount of solids entering the system is kept to a minimum, the tank will have a longer interval between pumpings.

Scum is formed at the top of the tank as a result of lighter material floating to the surface.

When sludge and scum accumulate in the tank, the effective tank volume decreases.
Furthermore, sediments might be transported to the drainfield, leading it to get clogged.
Have the tank pumped by a Nebraska pumper who is licensed and insured.

Under Title 124, rules set out by the Nebraska Department of Environmental Quality (NDEQ) limit the maximum amount of waste that can accumulate before pumping is necessary.
If you have any questions, please contact us.
As a result of gathering this information, your qualified professional will be better able to identify whether or not the level of sludge and scum in your tank has reached the point where pumping is necessary.

How many years have elapsed since the first pumping took place?
If the amount of wastewater generated varies, repeat the operation or alter the pumping frequency.

You may take steps to reduce the amount of sediments that enter your tank. First and foremost, avoid using a waste disposal or use it only rarely. According to studies, when a waste disposal is utilized, tanks must be pumped twice as often as when they are not. Other suggestions are as follows:

Cigarettes, diapers, feminine hygiene items, paper towels, face tissue, and “wipes” should not be flushed down the toilet. They may not decompose completely and will lead to the formation of scum or sludge layers. Dispose of these goods in the same manner as other solid garbage. Grease and oils should not be flushed down the toilet. Grease and oils from cooking, frying, and applying skin creams contribute to the formation of a scum layer in the septic system. Instead of powdered detergents, liquid detergents should be used. Powdered detergents include “fillers,” which contribute to the formation of the sludge layer. Make use of toilet tissue that decomposes quickly. To perform the test, place a tissue sample in a jar of water, cover the jar opening with a cloth, and shake vigorously. When the jar is shaken, the toilet paper should come apart in a short period of time. Filter the washing machine’s water output pipe to catch lint and prevent it from getting into the machine. Clean in accordance with the manufacturer’s recommendations

An effluent filter at the septic tank outflow can assist in preventing particles from entering the drainfield. Have it cleaned in accordance with the manufacturer’s recommendations

Septic Tank Pumping

Septic tanks are used in the vast majority of on-lot sewage systems nowadays. The subject of how frequently a septic tank should be pumped has been a source of contention for several decades. For example, there are some homeowners who say they have never drained their septic tank and that it “appears” to be in fine working condition. While trying to establish a standard pumping strategy, authorities have taken a more conservative approach and have declared that all septic tanks should be pump out every two to three years.

How a Septic Tank Works

Box 1.Can you tell me how much solid trash you generate? The average adult consumes around one quart of food every day. The body removes just a very little percentage of this meal and utilizes it to provide energy for the body’s functions. The remaining portion is discharged into the waste water system. This translates into around 90 gallons of solid waste being discharged into the septic tank per adult each year. Based on the assumption that the anaerobic bacteria in the septic tank reduce the waste volume by around 60%, this indicates that each adult contributes approximately 60 gallons of solids to their septic tank each year.

Consequently, it will take around 5 years for one adult to completely fill a 1,000-gallon septic tank with sludge and scum, which is approximately 300 gallons.
It is simple to infer that a septic tank should be pumped every two to three years after accounting for adults who work outside the home for a third of the time and children who attend school after making these modifications to the study.
Single chamber septic tanks were the most common type of septic tank until recently.

Septic tanks are designed to aid the removal of particles that are heavier than water by encouraging these heavy particles to settle to the tank bottom, resulting in the formation of the sludge layer.
It is also designed to keep particles that are lighter than water by encouraging these lighter particles to float to the surface and be maintained in the tank, resulting in a layer of scum on the surface of the tank.

In part, this is due to the fact that the temperature of the septic tank is equal to that of the soil surrounding it, and the anaerobic bacteria require higher temperatures in order to effectively decompose organic material in wastewater and thus reduce the biological oxygen demand (BOD) of the wastewater.

Holding on to the heavy (settleable) and lighter (floatable) particles allows the septic tank to gently fill with solids from the bottom up as well as from the top down.
Septic tanks with an exit filter will catch and decrease the flow of solids into the absorption area when the tank is properly designed and installed.
As a result, it is critical that every septic tank be pumped on a regular basis to eliminate the organic particles that have been collected and partially digested.

Small amounts of the particles kept in the tank degrade, but the vast majority of the solids stay and build up in the tank.
Under no circumstances should you enter a septic tank.
With continued usage of the on-lot wastewater disposal system, an accumulation of sludge and scum builds up in the septic tank.

As the amount of sludge and scum in the tank fills up, wastewater is maintained in the tank for a shorter period of time, and the solids removal process becomes less efficient as a result.

It is necessary to pump the tank on a regular basis in order to avoid this. Asseptage is the term used to describe the substance injected. Cross-sectional view of a two-chamber septic tank (Figure 1).

Number of bedrooms in the home	Estimated daily flow (gallons/day)	Minimum septic tank size (gallons)
3	400	900
4	500	1,250
5	600	1,400
6	700	1,550

How Frequent should a Septic Tank be Pumped?

Pumping frequency is determined by a number of parameters, including:

The capacity of the septic tank

The amount of wastewater that is put to the septic tank each day (see Table 1)
The amount of solids in a wastewater stream is measured. In this regard, it should be noted that there are various different types of particles that are regularly dumped into a septic system. This group of solids includes (1) biodegradable “organic” solids such as feces (see Box 1), (2) slowly biodegradable “organic” solids such as toilet paper and cellulosic compounds, which take a long time to biodegrade in the septic tank, and (3) non-biodegradable solids such as kitty litter, plastics, and other non-biodegradable materials, which do not biodegrade and quickly fill the septic tank It is possible to significantly reduce the quantity of slowly biodegradable organics and non-biodegradable trash that is introduced to your septic tank by reducing the amount of organic waste that is added to the tank.

Another factor that influences how soon a septic tank will fill with solids is one’s way of living. In terms of septic tank function, the two most essential aspects of one’s lifestyle are as follows: Homes with expanding families, having children ranging in age from tiny children to adolescents, often consume more water and deposit more sediments into the septic tank than other types of households. Empty nesters, and especially the elderly, on the other hand, have a tendency to consume significantly less water and to deposit significantly less solid waste in septic tanks.

The particles in a septic tank tend to be taken away from the tank to the soil absorption region, as previously indicated.
As additional materials collect in the absorption region, these sediments begin to choke the soil, preventing wastewater from being able to fully absorb.
In most cases, the removal of these biomats is both expensive and time-consuming.

Pumping the wastewater that has accumulated in the soil absorption area is required for the removal of the biomat.
The biomat normally decomposes within a few days after the absorption area has been completely dewatered and has been aerated.

Is It Time To Pump Your Septic Tank?

So, how does one go about determining how frequently a septic tank needs be cleaned? We are aware that residences who dispose of huge volumes of non-biodegradable and slowly biodegradable organic waste into their septic tank require more frequent pumping. It is also known that prior to the time at which the collected solids have accumulated to the point that they are being taken with the tank effluent to the absorption region, the septic tank should be pump out. When it comes to determining when (and how frequently) to pump your septic tank, there are two generally safe ways to use.

The alternative method is to open the access port to the first chamber (as shown in Figure 1) once a year and insert a long pole to the bottom of the tank and then pull it out of the tank.

If the sludge has accumulated to more than one-third of the tank’s total depth, it is time to have it drained out completely. The majority of households will benefit from having their tanks drained every two or three years instead.

The Pumping Process

Contractors who specialize in septic tank pumping and hauling may pump your septic tank. It is a good idea to be present to check that everything is completed correctly. For the material to be extracted from the tank, it is necessary to break up the scum layer, and the sludge layer must be combined with the liquid section of the tank. In most cases, this is accomplished by alternately pumping liquid out of the tank and re-injecting it into the bottom of the tank. Not the little intake or outlet inspection openings situated above each baffle, but the two huge central access ports (manholes) are required for pumping the septic tank.

It is not suggested to use additives in septic tanks to minimize the volume of sludge or as a substitute for pumping in order to achieve these goals.
When you have your septic tank pumped, you should consider taking an additional step to ensure that your septic system continues to perform correctly for a long time.
This inspector can tell you whether or not your septic tank needs to be repaired, as well as whether or not other components of your sewage system require upkeep.

Mark the position of the tank as well, so that it may be found simply in the future for pumping.

Schedule Septic Tank Pumping

Homeowners should develop the practice of getting their septic tanks drained on a regular basis. As long as you are able and willing to schedule regular septic tank pumping (every two or three years, for example), it may be feasible to improve the overall performance of your complete on-lot wastewater disposal system. According to research conducted at Penn State, your soil absorption system will benefit from frequent resting periods (a period during which no wastewater is added to the absorption area).

In other words, the whole system, particularly the soil absorption region, will have the opportunity to dry up, and any organic waste (biomat) that may have formed in the soil absorption area will degrade swiftly in the absence of water.

Summary

A septic tank is simply one component of a complete on-site wastewater treatment system. Its purpose is to remove solids from the effluent prior to it reaching the soil absorption region, to allow for the digestion of a part of those solids, and to store the remainder of the solids in a holding tank. It is not necessary to use biological or chemical additions to enhance or speed the breakdown process.

Grinders contribute to the solids load on the system by reducing the size of garbage. Solids must be removed on a regular basis in order to prevent them from accessing the soil absorption zone. Every two to three years, you should have your septic tank drained and examined by a professional.

For additional assistance contact

Your local Sewage Enforcement Officer or Extension Educator can help you with these issues. A contact for the Pennsylvania Association of Sewage Enforcement Officers (PASEO) is as follows:4902 Carlisle Pike,268Mechanicsburg, PA 17050 Phone: 717-761-8648 Email: [email protected] Philadelphia, PA 18016 717-763-7762 [email protected] Pennsylvania Septage Management Association (PSMA)P.O. Box 144 Bethlehem, PA 18016 717-763-7762

How Often Should You Pump Your Septic Tank?

The most often asked question we receive is “How often should I pump my septic tank?” This is by far the most common question we receive. New homeowners who are unfamiliar with septic systems are frequently required to learn how to properly manage their septic systems in order to avoid costly difficulties in the future. As an alternative to sewer systems and as an ecologically beneficial approach to handle domestic drain waste, a septic system is distinct from a sewer system and requires extra attention and upkeep to function properly.

Septic tank pumping should be done at the right interval for your home

The fact is that, while there are some broad suggestions that a septic system should be pumped every 2-5 years, the truth is that you actually only need to pump your system as frequently as your system requires. The amount of sludge and scum present in a septic tank is the most important element in determining how often it should be flushed. When your septic system functions, it does so by taking use of the natural force of gravity to break out the household wastewater into three distinct components:

Solids (sludge) accumulate at the bottom of the tank
Grease (scum) accumulates at the top of the tank

And watery mix (effluent) accumulates in the center of the tank.

When the system is operating normally, the sludge and scum remain in the septic tank while the watery mix drains out into the drain field. The sludge and scum in the septic tank, on the other hand, must be removed from time to time in order to keep things running well. Sludge levels that reach dangerous levels, and/or a scum layer that has developed to a significant thickness, will be driven out into the drain field together with the watery effluent, resulting in a clogging of the drain field.

This can result in the growth of harmful germs in your house, as well as the need for a costly repair.

Most homeowners pumping more often than necessary are overspending!

Essentially, by pumping your septic tank too frequently, there is not enough sludge and scum buildup in the tank to ensure that you earn the optimum return on your investment in the costs of pumping your tank. Paying for the service more frequently than you need to is a waste of money that provides no additional benefits, just like paying for any other periodic maintenance. The fact is that your septic system does require a certain number of beneficial bacteria to function properly. Septic tanks employ anaerobic digestion, which is similar to the digestive system of humans, to naturally break down waste before it is sent on to the next phase of treatment.

Yeast is a type of bacterium that enters your tank each time an organic waste material is flushed down the toilet, and it breaks down the waste material into sludge and effluent.

It is really beneficial to leave your septic tank alone unless the quantities of sludge and scum in your tank exceed specified criteria; otherwise, it is detrimental. This ensures that the proper balance of bacteria is maintained in order to keep your system running properly.

So, how will you knowhow often you should pump your septic tank?

As you can see, the sludge and scum levels in your septic tank are the two most important criteria in determining your plan of maintenance. You should have your septic tank pumped when the sludge level reaches one foot at the bottom of the tank, or when the scum layer at the top of the tank has grown to almost six inches in thickness at the top. Contrary to common assumption, the majority of homes do not require yearly pumping. It is purely dependent on the level of your tank, and not on a fixed time frame.

How to Find Out if Your Septic Tank is Full

To begin, find and gently remove the septic tank lid from its mounting bracket. Use extra caution to ensure that the heavy lid does not crack or shatter, and never leave the tank open while you are not watching it! If a person or a pet falls into the tank, which has 4-5 feet of water beneath, it may be quite deadly. In the following stage, you will examine the scum trap at the very top of the tank to see how thick the scum layer is. You should pump your septic tank when the scum level has reached 6 inches thick, as a general rule of thumb.

While it is possible to acquire a specialized sludge level measurement stick, it is also possible to create your own at yourself.

The velcro end will be the one that will be inserted into the aquarium.
Then, holding the measuring stick straight up, verify the velcro strip for accuracy.
The septic tank should be pumped after it has accumulated one foot (12 inches) of sludge, as recommended by the manufacturer.

Grant’s Septic Techs, in contrast to many other septic service companies, will actually use photographic documentation to show you exactly where your waste levels are, as well as to assist you in tracking the amount of time it takes for your scum and sludge levels to build up to the appropriate levels.

If you do not require septic pumping services, there is no reason to pay for them.
For the low price of $127, we will come to your home and do all of the necessary measurements for you.

We’ll take actual images of your systems to document their current state and create a personalized proposal for your unique timetable.
In fact, if we discover that your septic tank levels require pumping at the time of inspection, we will not charge you for the measurement service.
In order to maintain the health of your septic system and get on the bestseptic tank pumping maintenance plan for your house, please contact Grant Septic Technologies at (508) 529-6255 or book a septic tank pumping appointment conveniently online.

Check to see whether your town is included in our Massachusetts service region by entering your address here.

How to Inspect Your Septic Tank – Septic Maxx

If you give your septic system the attention and care it deserves, it will survive a long time. It will endure for many years if you pump as regularly as you need to for the size of your tank, utilize it properly, and do not let anything that shouldn’t be in it to enter. Steel septic tanks corrode with time, generally after 15-20 years of service in most climates. Concrete septic tanks have a lifespan ranging from 40 years to nearly indefinitely. If you want to see your septic system live to a ripe old age and not have to worry about replacing it, it is in your best interests to do periodic septic maintenance.

Gather Materials

It is necessary to have the correct equipment in order to assess the state of your septic tank and determine whether it is necessary to have it pumped out. Aside from wearing loose-fitting clothes and rubber gloves and shoes, you’ll need a specific gadget known as a Sludge Judge to quantify the quantities of scum and sludge that are present in your tank. This instrument is basically a transparent plastic pipe that has been marked at one-foot intervals and divided into three pieces, each of which is five feet in length.

Sludge, effluent, and scum are the three types of waste that accumulate in a septic tank.

Scum is formed when fats, oils, cooking grease, and other lighter trash float to the surface of the water.

To check your tank, you must first assess how much sludge and scum is present within in order to evaluate whether or not it needs to be pumped.

Inspect the Area Around Your Septic Tank

Checking the ground around your septic tank is a good idea before opening the lid and pumping out the sewage. Check to see if there is any accumulation of effluent around the tank, and look over the septic tank lid to check whether it is in good shape.

Remove the Manhole Cover

Many septic systems these days are equipped with ” risers,” which make this task much easier by elevating the lids above earth. If you are unable to locate the lid of your septic tank, locate the tank and dig it up. There should be two lids, one for each compartment, in the box. In the majority of situations, the hole on the left corresponds to the first compartment, while the hole on the right corresponds to the second. In the first one, you simply need to take measurements, and that’s all.

Measure the Scum’s Thickness (SC)

To determine how thick the scum layer is in your tank, you’ll need to go for your trusty scum measuring stick, of course. Measure the distance between the stick and the opening of the septic tank, and then lower the stick until it lies on top of the scum layer and indicate the location of this intersection. As a further step, descend down through the whole scum layer with the elbow end leading directly into the scum layer. Rotate the stick 90 degrees and raise the stick as high as you can until you feel the bottom of the scum layer.

Mark the spot on the scum stick where it comes into contact with the bottom of the scum layer. Take the distance between the two markers and multiply it by two. This is the measurement of the thickness of the scum layer (SC).

Measure the Sludge’s Thickness (SL)

Make a hole in the scum layer with your handy sludge measuring stick and carefully lower the stick through it after tying two feet of a white cloth to the stick. Mark the point on the stick where it comes into contact with the aperture of the manhole or riser. After that, drop it to the very bottom of the tank and keep it there for 5 minutes to allow the sludge to adhere to the cloth towel. Measure the distance between the tanks or the operating depth of the tank. Remove the stick and use the rag to measure the height of the dark stain that should be visible on it.

Following the completion of these measures, you will be able to calculate when it is necessary to pump your septic tank.

SC plus SL equals inches

WD inches divided by 3 equals inches
If the sum of A and B equals the sum of A and B, pump your tank.

It is recommended that you engage a professional to examine your tank in order to get an accurate reading; but, if you are comfortable doing it yourself, you may save money by using this approach. Besides saving you money, Septic Maxx may also save you money by reducing the amount of accumulation in your tank and so extending the intervals between pumping.

What are the Septic Tank Layers?

Sludge, effluent, and scum are the three layers of wastewater that make up your septic tank: sludge, effluent, and scum. You will have a perfectly functioning septic system when each of these wastewater layers is correctly balanced. As a homeowner, you should become familiar with the indications that indicate when the sludge layer has become overburdened and when your septic tank needs to be drained.

What Are The Three Layers of Wastewater?

Scum is the substance that makes up the top layer of the septic system. When items like soap byproducts and cooking oils reach the top of the wastewater tank, they create this scum. Effluent is the wastewater that remains in the intermediate layer of the septic tank after the scum has risen to the top of the tank and the sludge has sunk to the bottom of the tank, which is known as the effluent layer. In certain cases, it may contain minute particles of waste items. When your septic system is operating properly, the effluent/water is released into the drain field from the tank
However, this is not always the case. In your septic system, sludge makes up the lowest layer, which is made up of a substance known as sludge. In your septic tank, sludge is made up of byproducts of the breakdown of various waste materials that have been disposed of in the tank. Heavy items that sink to the bottom of the septic tank become a part of the sludge as a result.

Pumping the sludge out of your tank on a regular basis is essential for keeping your septic system in excellent operating order. Find out how often you should pump your septic tank by reading this article. The Septic Medic team may be contacted online or by phone at 570-828-7444 to book routine septic maintenance or a routine tank pumping for homeowners in Pike County, Pennsylvania, including Delaware Township and the surrounding suburbs of Northeastern Pennsylvania.

Septic Emergency? Contact us immediately at570-828-7444

Services Provided by Septic Medics:

Septic System Pumping and Tank Cleaning

Repair of a Clogged Drainor Septic System Back Up
Septic System Maintenance for Tanks
Septic System Pumping and Tank Cleaning Leach Fields

Septic Tank Repair or Replacement
Septic Tank Maintenance

Taking Care of Septic Sludge Buildup

Written by aby on September 28, 2017 at 11:28 a.m The water that enters the septic tank contains a diverse range of particles and compounds. As much of the solids as possible is decomposed by aerobic bacteria in the tank; the remainder sinks to the bottom and forms a layer of septic sludge on the bottom. The accumulation of sludge in the tank might cause a variety of major issues.

The problem with too much sludge.

Septic sludge is a typical part of every septic tank’s operation. Aerobic bacteria are unable to digest all of the solid waste that enters the system due to a lack of oxygen. As a result, sludge accumulates in layers on the tank floor. Ultimately, as time goes on, the sludge layer will continue to grow in depth until it eventually overflows. ” If the sludge is not cleaned, it will collect until it ultimately overflows, obstructing the soil absorption area once more.” Water cannot flow into the soil and filter naturally if there is a buildup of septic waste in the drain field.

The water will continue to rise and overflow the drainage area since it has nowhere else to go.

An ounce of maintenance is always best.

The sludge at the bottom of the tank will remain in place until it is pumped out and disposed of properly. Approximately how often should a tank be pumped in order to avoid harmful sludge formation. To calculate the frequency of maintenance, there are a variety of options, including measuring the sludge depth using a do-it-yourself equipment, making an educated guess about the depth based on the number of people who use the system, and consulting with the experts. Have the tank pumped and then ask the technician when the next filling will be necessary.

Keeping the sludge down with added bacteria.

Using a bacterial supplement in the tank between cleanings is the most effective technique to keep septic sludge under control between cleanings. Bacterial additions provide a healthy dosage of additional aerobic bacteria to the tanks, which aid in the decomposition of solid waste. The hard-working bacteria keep sludge levels from increasing too rapidly and generating difficulties in the environment. For additional information on preventing sludge overflow and septic maintenance programs, please get in touch with us.

Here’s What You Should Do.

About Author

Septic system maintenance is neither difficult or expensive, and it does not have to be done frequently. The maintenance of a vehicle is comprised of four major components:

Inspect and pump your drainfield on a regular basis
Conserve water
Dispose of waste properly
And keep your drainfield in good condition.

Inspect and Pump Frequently

Inspection of the ordinary residential septic system should be performed by a septic service specialist at least once every three years. Household septic tanks are normally pumped every three to five years, depending on how often they are used. Alternative systems that use electrical float switches, pumps, or mechanical components should be examined more frequently, typically once a year, to ensure that they are in proper working order. Because alternative systems contain mechanical components, it is essential to have a service contract.

The size of the household
The total amount of wastewater produced
The amount of solids present in wastewater
The size of the septic tank

Service provider coming? Here is what you need to know.

When you contact a septic service provider, he or she will inspect your septic tank for leaks as well as the scum and sludge layers that have built up over time. Maintain detailed records of any maintenance work conducted on your septic system. Because of the T-shaped outlet on the side of your tank, sludge and scum will not be able to escape from the tank and travel to the drainfield region. A pumping is required when the bottom of the scum layer or the top of the sludge layer is within six inches of the bottom of the outlet, or if the top of the sludge layer is within 12 inches of the bottom of the outlet.

In the service report for your system, the service provider should mention the completion of repairs as well as the condition of the tank.

If additional repairs are recommended, contact a repair professional as soon as possible. An online septic finder from the National Onsite Wastewater Recycling Association (NOWRA) makes it simple to identify service specialists in your region.

Use Water Efficiently

In a normal single-family house, the average indoor water consumption is about 70 gallons per person, per day, on average. A single leaking or running toilet can waste as much as 200 gallons of water each day, depending on the situation. The septic system is responsible for disposing of all of the water that a residence sends down its pipes. The more water that is conserved in a household, the less water that enters the sewage system. A septic system that is operated efficiently will operate more efficiently and will have a lower chance of failure.

Toilets with a high level of efficiency. The usage of toilets accounts for 25 to 30% of total home water use. Many older homes have toilets with reservoirs that hold 3.5 to 5 gallons of water, but contemporary, high-efficiency toilets consume 1.6 gallons or less of water for each flush. Changing out your old toilets for high-efficiency versions is a simple approach to lessen the amount of household water that gets into your septic system. Aerators for faucets and high-efficiency showerheads are also available. Reduce water use and the volume of water entering your septic system by using faucet aerators, high-efficiency showerheads, and shower flow restriction devices. Machines for washing clothes. Water and energy are wasted when little loads of laundry are washed on the large-load cycle of your washing machine. By selecting the appropriate load size, you may limit the amount of water wasted. If you are unable to specify a load size, only complete loads of washing should be performed. Washing machine use should be spread throughout the week if at all possible. Doing all of your household laundry in one day may appear to be a time-saving strategy
Nevertheless, it can cause damage to your septic system by denying your septic tank adequate time to handle waste and may even cause your drainfield to overflow. Machines that have earned theENERGY STARlabel consume 35 percent less energy and 50 percent less water than ordinary ones, according to the Environmental Protection Agency. Other Energy Star appliances can save you a lot of money on your energy and water bills.

Properly Dispose of Waste

Everything that goes down your drains, whether it’s flushed down the toilet, ground up in the trash disposal, or poured down the sink, shower, or bath, ends up in your septic system, which is where it belongs. What you flush down the toilet has an impact on how effectively your septic system functions.

Toilets aren’t trash cans!

Your septic system is not a garbage disposal system. A simple rule of thumb is to never flush anything other than human waste and toilet paper down the toilet. Never flush a toilet:

Cooking grease or oil
Wipes that are not flushable, such as baby wipes or other wet wipes
Photographic solutions
Feminine hygiene items Condoms
Medical supplies such as dental floss and disposable diapers, cigarette butts and coffee grounds, cat litter and paper towels, pharmaceuticals, and household chemicals such as gasoline and oil, insecticides, antifreeze, and paint or paint thinners

Toilet Paper Needs to Be Flushed! Check out this video, which demonstrates why the only item you should flush down your toilet are toilet paper rolls.

Think at the sink!

Your septic system is made up of a collection of living organisms that digest and treat the waste generated by your household. Pouring pollutants down your drain can kill these organisms and cause damage to your septic system as well as other things. Whether you’re at the kitchen sink, the bathtub, or the utility sink, remember the following:

If you have a clogged drain, avoid using chemical drain openers. To prevent this from happening, use hot water or a drain snake
Never dump cooking oil or grease down the sink or toilet. It is never a good idea to flush oil-based paints, solvents, or huge quantities of harmful cleansers down the toilet. Even latex paint waste should be kept to a bare minimum. Disposal of rubbish should be avoided or limited to a minimum. Fats, grease, and particles will be considerably reduced in your septic tank, reducing the likelihood of your drainfield being clogged.

Own a recreational vehicle (RV), boat or mobile home?

If you have ever spent any time in an RV or boat, you are undoubtedly familiar with the issue of aromas emanating from sewage holding tanks.

The National Small Flows Clearinghouse’s Septic System Care hotline, which may be reached toll-free at 800-624-8301, has a factsheet on safe wastewater disposal for RV, boat, and mobile home owners and operators.

Maintain Your Drainfield

It is critical that you maintain the integrity of your drainfield, which is a component of your septic system that filters impurities from the liquid that emerges from your septic tank once it has been installed. Here are some things you should do to keep it in good condition:

Parking: Do not park or drive on your drainfield at any time. Plan your tree plantings so that their roots do not grow into your drainfield or septic system. An experienced septic service provider can recommend the appropriate distance for your septic tank and surrounding landscaping, based on your specific situation. Locating Your Drainfield: Keep any roof drains, sump pumps, and other rainfall drainage systems away from the drainfield area. Excess water causes the wastewater treatment process to slow down or halt completely.

3 Factors That Determine When to Pump Your Septic Tank

Septic systems, in general, have a limited carrying capacity. The breakdown of solid waste leads in the production of a layer of sludge at the bottom of the tank as a result of the passage of time. Because of the increasing volume of sludge, the tank’s capacity is becoming increasingly limited. It is necessary to pump off collected sludge from your tank on a regular basis to prevent backflow and floods. It is recommended that a septic tank be pumped every two to three years, according to the general rule of thumb.

The frequency with which you require expert service is determined by a variety of factors.
1.
The majority of household septic tanks have a capacity of between 750 and 2,000 gallons of capacity.
Some installers, on the other hand, size tanks in accordance with the number of bedrooms in a house.
It’s possible that your family has more members than the prior owner’s.
If you are unsure about the size of your septic tank, look through the documents you received when you acquired your property.
If this is not the case, see a specialist.

If this is the case, they will be able to measure the tank’s capacity while it is being pumped.

The amount of solid waste generated Depending on the kind of waste, liquid and solid septic systems manage it differently.

Dispersing the liquid waste into the soil is accomplished by pipes placed beneath the surface of the earth, where it continues to decompose until it finally enters ground water.

Instead, anaerobic bacteria species break down the trash over time, allowing it to decompose naturally.

When the solid waste content of a tank reaches between 35 and 50 percent of the tank’s total capacity, it is necessary to pump the tank.

Solid waste does not decompose at the same pace in all situations.

Other forms of organic substances decompose more slowly than others.

Certain solids do not degrade in any way and are thus non biodegradable.

In a septic tank, non-biodegradable materials take up significantly more space than biodegradable solids since their volume does not diminish with time.

Non-biodegradable solids will not only increase the frequency with which you must pump your tank, but they will also raise the possibility of blockages and other difficulties.

The Consumption of Water The amount of water that you put into your septic system has an impact on how well the biological breakdown process goes in your system.

As a result, solid waste will not decompose at the same pace as liquid waste, causing your tank to fill up more rapidly.

For more information on what you can do to keep your septic system in good operating order, please call Walters Environmental Services, a septic system expert serving central Pennsylvania and the surrounding areas.

Misconceptions of Septic Systems

You never have to have the septic tank pumped.As the septic system is used, the solids (sludge) accumulate on the bottom of the septic tank(s). When the sludge level increases, sewage has less time to settle properly before leaving the tank through the outlet pipe and a greater percent of suspended solids escape into the absorption area. If sludge accumulates too long, no settling of the solids will occur, and the solids will be able to directly enter the absorption area. These solids will clog the distribution lines and soil and cause serious and expensive problems for the homeowner. To prevent this, the tank must be pumped out on a regular basis.If you use additives you don’t have to have the tank pumped.The claims made by companies that sell additives are that you never have to pump your tank. What the products do is break up the scum and sludge so that there is a greater percent ofsuspended solidsin the tank that then flow down the over flow pipe with the effluent to your absorption area, causing your system to fail.The absorption area is designed to treat water or effluent, not solids.The septic tank is designed to contain and treat the solids and they should remain in the tank. It is much less costly to pump your tank on a routine basis than ultimately having to replace your absorption area.It takes years between having the tank pumped for the septic tank to fill to its capacity.The average usage for a family of four will fill a septic tank to its working capacity of 1000 – 1500 gallons in approximately one week. When the contents (liquids and solids) in the tank reaches the level of the overflow pipe, the effluent flows down the overflow pipe to the absorption area every time water is used in the house.The tank works at this full level until it is emptied when it is pumped again.When the alarm for the pump sounds it means you need to pump your tank.If you have a system designed with a pump to pump the effluent to the absorption area you also have an alarm for the septic system.The alarm sounds when the water level rises in the pump tank and alerts you that there is a malfunction with your pump, float switches, or other component in the pump tank.It does not mean that it is time for a routine pumping of your tank.

How Often Are Septic Tanks Emptied, and Where Do the Contents Go?

It’s safe to assume that wherever there are many individuals who run their houses’ waste systems through septic tanks, there will be a slew of local firms that specialize in eliminating the scum and sludge that collect in the tank over a long period of time. This is a crucial service because, if too much sludge accumulates over time, it can cause overflow, which is harmful to everyone involved. Septic pumping for commercial purposes typically consists of a pump truck emptying the sludge, effluent, and scum from the tank and leaving the tank empty and ready to be refilled with fresh sludge and water.

Prior to the passage of federal legislation prohibiting the disposal of sewage sludge, waste management businesses could simply bury it in landfills.

These locations still exist, however many of them are in the process of being cleaned up (clean-up).

In certain situations, the septic contents are transported to waste treatment plants where they are combined with the stew that has been pumped in from a municipal sewer system, or they are supplied to for-profit organizations that specialize in the treatment of septage.

Septage may also be placed at landfills that have been allowed.

Because of the difficulties associated with properly disposing of your septic tank’s contents, septage is sometimes employed in a different way: to grow food.

This application of septage has the potential to be contentious.

It is expected that, when properly applied to farmland with good soil and a low water table, the soil will work as a filter in the same way as a drain field in the rear of a home with a septic tank will act as a filter.

Historically, it has been recognized that methane, which is created as a waste product during the breakdown of sewage, may be utilized to generate energy.

In addition, because the power produced does not burn, there is little or no pollutants emitted.

One system, constructed south of Seattle, Washington, in 2004, has the capacity to generate enough electricity to power 1,000 houses.

Who would have thought that your feces could be so beneficial? More information about waste treatment may be found on the next page. The original publication date was July 29, 2008.