How Much Does Septic Tank Installation Cost In Georgia? (Best solution)

Plumbing Excavation and Installation of Septic Tank and Pumps. Once you have obtained your permit, you can begin contacting your local septic system service company for excavation and installation. Depending on your property and your septic system’s size, you can expect to spend at least $1500 to upwards of $3000.

  • As our numbers show in 2021 average cost that homeowners paid for septic tank installation in Dodge county is between $1,153.00 and $8,116.00. Average labor costs to install a septic tank in Eastman, Georgia.

Can I install my own septic system in Georgia?

Septic tanks installed after February 20, 2000 are required to have two compartments and an effluent filter. The minimum size septic tank approved for use in the State of Georgia is a 1000 gallon tank, which will serve a 3 or 4 bedroom house.

How much does it cost to replace a septic system in GA?

Septic Tank System Cost A new septic tank system costs $3,918 to install on average, with prices ranging from $1,500 to upward of $5,000. Most homeowners spend between $3,280 and $5,040 for a 1,250-gallon system that supports 3 or 4 bedrooms.

How far should a septic tank be from a house?

Most importantly, a septic tank must be at least seven metres from a house, defined as a ‘habitable property’. Septic tanks are built underground and release wastewater slowly into the surrounding environment. For this reason, they must be a set distance away from a home.

How far does a septic tank have to be from a house in Georgia?

Normally, the distance a septic tank should be located from a building foundation is at least ten feet (10′) but, lesser distances may be allowed by the County Board of Health.

What is the cheapest septic system?

Conventional septic system These conventional septic systems are usually the most affordable, with an average cost of around $3,000.

What are the 3 types of septic systems?

Types of Septic Systems

  • Septic Tank.
  • Conventional System.
  • Chamber System.
  • Drip Distribution System.
  • Aerobic Treatment Unit.
  • Mound Systems.
  • Recirculating Sand Filter System.
  • Evapotranspiration System.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Why do I smell my septic tank when it rains?

Raining often causes atmospheric pressure changes, which can lead to the air becoming heavy. As such, the methane gases typically found in the septic tank don’t flow through the vent as they normally would. Instead, they stay low to the ground, causing a foul smell similar to rotten eggs.

Can I build a deck over my septic tank?

You should never build a deck over a septic field; doing so will prevent the natural draining and dissipation of the effluent. This can ruin the septic system, not to mention releasing foul smells into the air all around your deck. The dissipating effluent can also rot the deck from underneath.

Is planning permission required for septic tank?

The short answer is yes. You will need planning permission from a local authority in order to have a septic tank installed, no matter if it’s at your own home or on a business site.

Are outhouses legal in Georgia?

Off-grid sewage treatment systems are somewhat legal in Georgia. If your property is within 200 feet of a public sewer line, you will be required to connect to it. However, there are some exceptions for homes which use alternative systems, so long as those systems meet requirements.

Cost of Septic System: From Planning to Install – Call (229) 415-7780

An exact cost for a septic system cannot be determined with absolute certainty. There are several aspects that must be taken into consideration, and some of them cannot be determined without first visiting the site where the unit is to be installed in person. The cost of a standard gravity-fed unit is in the range of $10,000-12,000, but we’ve broken down the cost of a septic system depending on the procedures involved, so you can have a better understanding of what you should expect. You should contact us if you need to deal with concrete numbers, since your final pricing may be lower or significantly greater than what’s displayed on this page.

Cost of Septic System Planning, Design, and Install

A well-designed system is a technical achievement in and of itself. When everything is correctly organized, your unit will operate smoothly and survive for decades. The expenses connected with the planning, design, and installation will normally range between $1,500 and $4,000 per hour of labor. Things like the following are included: Inspection of the site: Several general characteristics of the site will be recorded, such as the amount of vegetation that will need to be cleared and how difficult it will be to get access to the property.

The average unit requires a grade of 15 percent or less.

  • In addition, the assessor will need to identify where the water table is located in order to decide whether or not a typical leach field is acceptable.
  • If the water soaks in too quickly or too slowly, a leach field may not be the best option.
  • This is a rather uncommon occurrence, particularly in Georgia.
  • This enables the provider to present you with an estimate and obtain approval from the county before beginning work on your project.

Price of the Tank

The majority of modern homeowners find that a 1,000-gallon reservoir is sufficient for their needs. Concrete is usually the most cost-effective option, and it might cost up to $800-1,000 in all of itself. Fiberglass is typically less expensive than concrete, yet it is typically only utilized when the site circumstances make moving a cement reservoir problematic or impossible. Plastic is the final and most expensive alternative. It’s not as long-lasting, but it might save you a couple hundred dollars on the purchase price.

Steel reservoirs, long considered acceptable, are now considered unlawful in many countries and rust fast, making them a less attractive alternative than they once were. It is possible that you will require a bigger or smaller reservoir, and that your expenditures would fluctuate accordingly.

Price of the Leach Field

The leach field is responsible for releasing the water/effluent into the soil, where it completes the treatment process there. Because there is so much to consider, the expenditures related with the leach field often account for half of the total charges. Excavation: Trenches must be dug to allow for the proper placement of all of the lines. A typical size for them is between 8-12 inches broad and 2-3 feet deep. Pipes: The size of the leach field is determined by the soil characteristics on the site.

A budget of $65-80 should be put up for every 100 feet of pipe.

It will cost between $15 and $30 a ton, depending on where it is sourced and how far it needs to travel to get to you.

Additional Costs

There may also be some extra expenditures, such as those related with the inclusion of risers in the design of the building. These raise the level of the access ports to ground level, eliminating the need to excavate (or pay to excavate) when the unit need pumping or service in the future. Depending on the size and the materials used, they might cost anywhere from $100 to $200 or more.

Call Septic Tank Pros Valdosta GA to Get the Cost of Septic System for You

Your expenditures might be greater or lower than what’s stated here because there are so many variables to consider, such as the condition of the land, soil absorption, and how you utilize water, among others. Call us at (229) 415-7780 right away if you’d like an estimate prepared for you.

Cost of Septic Tank: Estimates and Guidelines

It’s not always straightforward to figure out how much a septic tank will cost. Visit Atlanta septic tank pros for all the information you want, or contact us at (404) 998-8812 for more information. ” data-image-caption=”Septic Tank Estimates and Guidelines” data-image-caption=”Septic Tank Estimates and Guidelines” data-medium-file=” data-large-file=” data-small-file=” Getting an accurate estimate for the cost of a septic tank is difficult since each home or company will require specific designs to be set up depending on the amount of people who will be using it, the soil conditions, and other variables.

When you call Atlanta Septic Tank Pros, our partner specialists will answer any questions you have about your tank as well as do any necessary installation, maintenance, pumping, and repair work.

If you’re merely interested in getting a broad estimate of how much a septic tank will cost, you’ll find all the information you need below.

Factors Included in the Cost of a Septic Tank

Given that there isn’t an one strategy that works for everyone, you’ll need to take a few factors into mind while putting together your estimate.

Size

Although the table shown here can be used as a general guideline, local rules may determine the minimum size that is required. Always consult with a specialist to confirm that the size you’re considering is within the legal parameters of your jurisdiction.

Occupants

4 2 1-2 18 1000
6 3 1-2 18 1000
8 4 2-3 25 1250
10 5 24 32 1500
12 6 3-5 39 2000
14 7 3-5 42 2000

Materials

There are a few different materials from which reservoirs may be constructed, however, as mentioned previously, local codes, your soil, and environmental circumstances may limit your selections to some extent. Each option has its own set of advantages and disadvantages. Cement: Cement is used to construct the vast bulk of the units. It’s long-lasting, frequently lasting 40 years or more, albeit it’s the most expensive of the options available. Fiberglass: When getting a cement unit to the job site is challenging, fiberglass is usually the next best alternative.

Stainless steel: While corrosion and local codes have mostly eliminated steel as a viable alternative, some steel reservoirs are still in use, so it’s worth noting that this is a possibility.

The fact that it is legal in most locations and can save you a few dollars if you are faced with an unexpected installation or replacement is not as impressive as the other alternatives.

How Much is a Septic Tank by Itself?

Most households can get by with a 1,000-gallon tank, which costs around $1,000-1,200 if it’s constructed of cement and can last for several years. Fiberglass is a reasonably cost material. Plastic is often a couple hundred dollars less expensive.

Other Expenses to Account for in the Cost of a Septic Tank

If you’re installing a new or replacement reservoir, you’ll need to get permits, and the job should always be conducted by a licensed expert. Additional information may be found on our website about complete system installations as well as about changing merely the reservoir on an existing system.

Contact Atlanta Septic Tank Pros to Get Your Cost of Septic Tank Estimate

For this reason, we recommend booking an appointment with one of our professional partner experts to go through your system’s requirements and verify that the installation is completed appropriately. If you would like additional information or to schedule an appointment, please contact us at (404) 998-8812.

Septic Tank Installation Cost: A Basic Pricing Guide

Obtaining an estimate for septic tank installation costs from Atlanta septic tank professionals is simple. Call us at (404) 998-8812 for a free estimate right away.” data-image-caption=”Septic Tank Installation Cost A Basic Pricing Guide” data-image-caption=”Septic Tank Installation Cost A Basic Pricing Guide” data-medium-file=” data-large-file=” data-small-file=” The process of collecting septic tank installation cost estimates is complicated, and it’s hard to provide a written full quote that is appropriate for everyone.

In the event that you need to work with hard numbers, please contact us as soon as possible so that one of our partner professionals may check through your specifications and requirements to make sure that the estimate is appropriate for the sort of system you want.

However, if you are just beginning started on your information search, this page might serve as a broad guide to get you started on the right track.

Is it New or a Replacement?

It is customary to refer to only the reservoir portion of a septic system’s installation, which serves as the initial step of the system’s processing. In the case of a system that does not already have a leach field or other absorption region, there is more to it than simply acquiring a reservoir. Please read our “Cost of Septic System” page for further information. The remainder of what you’ll discover on this page is exclusive to the reservoir alone, making it an excellent choice for homeowners who already have a system and simply need to replace the reservoir.

Are You Sure You Need a Replacement?

The fact that reservoirs typically endure decades should be noted before moving on to the financial aspects of the project. For those formed of cement, it is fairly usual that they will survive for 40 years or more. If your system is malfunctioning, it’s likely that the reservoir is not the source of the problem. Call us and we’ll dispatch a partner technician to your location to diagnose the problem. Alternatively, you may consult our guide to typical septic tank problems to narrow down which component of the system is causing the problem.

See also:  How To Abandon A Septic Tank In Mchenry County Illinois? (Perfect answer)

Information Needed in Determining Septic Tank Installation Cost

Size: A 1,000-gallon reservoir is considered enough by the majority of homeowners. It’s often suitable for groups of up to six people or for a four-bedroom house in most cases. It is normally required to have a 1,200-gallon tank if a fifth bedroom is being used, and a 1,500-gallon tank is preferable if there are six bedrooms. Regulations dictate the smallest size you may pick for the reasons of health and safety, but if you have normal water use and a typical-sized family, a 1,000-gallon tank should be plenty.

  • The most often used material for reservoirs is cement, with fiberglass a close second in popularity.
  • In general, a 1,000-gallon cement reservoir will cost in the area of $1,000-1,200, according to industry standards.
  • You should expect to pay around $100 for one of them.
  • Those that are lightweight can frequently be removed and disposed of.
  • This means that a new hole will have to be excavated in order to accommodate the replacement unit.

Call Atlanta Septic Tank Pros to Get Your Septic Tank Installation Cost Estimate

If you prefer to deal with figures rather than words, our partner specialists can gather the information they want from you in order to offer you with a more accurate estimate.

Please contact us at (404) 998-8812 if you would like further information or to make an appointment.

Do I need a new septic tank and how much does it cost in Atlanta GA?

  1. The following topics are covered: Home
  2. Blog
  3. Do I need a new septic tank and how much does it cost in Atlanta GA

Is it necessary to replace my septic tank? The very first call Simple: clean your sewage system and call us to come do a septic check. We are a fully licensed and insured business. According to the reason for the system failure, we can decide what repairs are required. These repairs might be modest or severe, depending on the situation. We will make certain that we present you with the most appropriate option. What is the cost of a new septic tank system? You might be asking how much it will cost to install a new septic tank; the answer is that it varies.

For your convenience, we at Easy Clean Septic offer free personalized quotes tailored to your specific requirements.

A skilled and licensed specialist will do a thorough investigation of your property and listen to your requirements in order to deliver an accurate quote.

Occupants

4 2 1-2 18 1000
6 3 1-2 18 1000
8 4 2-3 25 1250
10 5 24 32 1500
12 6 3-5 39 2000
14 7 3-5 42 2000

Factors that influence the price of a septic tank include: As we all know, there is no such thing as a one-size-fits-all solution, and this is especially true when it comes to clothing. Because all septic tanks are the same, you must take this into mind when following the basic principles provided in this section. The county inspector has the ultimate word on the size of the septic tank that will be installed on your property. Georgia has an environmental health agency with an inspector who determines the capacity of a septic system and makes recommendations to the county commissioners.

  • We will ensure that your tank complies with all the legal requirements in your jurisdiction.
  • Typically, a 1,000-gallon tank would enough for most households, which will cost between $1,000 and $1,500 in total.
  • If you are building a new or replacement septic tank in your county, you must obtain a permission from the local government.
  • Get in touch with Easy Clean Septic to receive an exact quote on the cost of a septic tank installation.

Learn how much it costs to Install a Septic Tank.

Septic tanks range in price from $3,157 to $10,367, or an average of $6,743. Installation of a conventional 1,000-gallon tank for a three-bedroom home might cost anywhere from $2,100 and $5,000. Materials range in price from $600 to $2,500, without labor. A comprehensive septic system, which includes a leach field (also known as a drain field), tank, and plumbing, can cost between $10,000 and $25,000 to install. A leach field installation might cost anywhere from $5,000 to $20,000, depending on the kind.

In the end, the cost of installing a septic tank is determined by the kind of system, the materials used, and the size of the tank.

The two types of systems covered in this book are aerobic and anaerobic systems. This course will teach you about the several sorts of settings, such as conventional, drip irrigation, mound irrigation, evapotranspiration, recirculating sand, constructed wetland, and chambered irrigation.

Septic System Cost Estimator

Let’s run some numbers to see what the costs are. What part of the world are you in? What part of the world are you in?

National Average $6,743
Typical Range $3,157 – $10,367
Low End – High End $450 – $20,000

The cost information in this report is based on real project costs provided by 943 HomeAdvisor users.

New Septic System Cost

Most tanks and systems cost between $2,000 and $10,000 to install a new typical anaerobic septic system. Aerobic systems range in price from $8,000 to $20,000. Depending on the size of your property, the composition of the soil, and the level of the water table, you may even have to pay an extra $10,000 or more for an alternative, specialized drain or leach field. Septic systems are composed of three major components:

  • Septic tank: Either anaerobic (requiring no oxygen) or aerobic (requiring oxygen but more complicated but more efficient)
  • Water runs to a leach field after it has been cleaned and separated in the septic tank, where it will naturally drain through sand, gravel, and soil in a cleaning process before reaching the water table
  • Water table: Plumbing: A drainpipe to the tank, followed by another branching pipe to your field will be required.

Optional components include the following:

  • Some types of systems use a dose or pump tank, which pumps wastewater up into mounded or elevated leach fields and recycles the water in some cases. Pump for aeration: If your aquarium is equipped with an aerobic system, you’ll want an aerator to force oxygen into the tank.
Find Local Septic Tank Installers

The installation of a traditional anaerobic system typically costs between $3,000 and $8,000 on average. Anaerobic systems are often less expensive to build than aerobic systems, which are more complicated. However, because they are less effective at cleaning the tank, you will need a bigger leach field to accommodate the increased burden. An anaerobic septic system is a very basic system that consists of a pipe that runs from the home to the tank and a branching pipe that runs from the tank to the drain field, among other components.

Aerobic Septic System Cost

Aerobic systems, which are those that require oxygen to work properly, cost on average between $10,000 and $20,000 per system. If you’re moving from anaerobic to aerobic fermentation, you’ll almost certainly need a second tank, but the conversion will only cost you $5,000 to $10,000. Aerobic systems break down waste more effectively in the tank than anaerobic systems, allowing you to use a smaller drain field in many cases – which is ideal for houses with limited space. An aerobic wastewater system is a wastewater system that depends on aerobic bacteria (bacteria that thrive in the presence of oxygen) to break down trash in the tank.

You’ll need an aerator as well as an electrical circuit that connects to the system to complete the setup.

Get Quotes From Local Septic Tank Pros

Beyond the tank and leach field, there will be a few more costs to consider when creating your budget for the project. You may already have some of these costs included in your total project pricing, so make sure to get line-item prices on your estimate.

  • Excavation costs $1,200–$4,500
  • Building permits cost $400–$2,000
  • And a perc test costs $700–$1,300. Labor costs range from $1,500 to $4,000
  • The cost of septic tank material ranges between $500 and $2,000.
  • Plastic and polymer materials cost $500–$2,500
  • Concrete costs $700–$2,000
  • And fiberglass costs $1,200–$2,000.
  • 500: $500–$900
  • 750: $700–$1,200
  • 1,000: $900–$1,500
  • 1,200: $1,200–$1,600
  • 1,500: $1,500–$2,500
  • 2,000: $3,000–$4,000
  • 3,000: $4,500–$6,000
  • 5,000+: $7,500–$14,000
  • 500: $500–$900
  • 1,200: $1,200–$1,

Leach Field Cost

Installing a leach or drain field, which is a component of your septic system, can cost anywhere from $3,000 to $15,000 in total. The cost of a typical drain field ranges from $2,000 to $10,000. The drain field, also known as the leach field, is the component of the septic system that is responsible for returning wastewater to the soil. Most of the time, a flooded area in the yard or a strong stink of sewage on the property is the first symptom of a problem with the drainfield.

It is possible that you may require further treatment for blocked or flooded fields, which would increase the cost of the drain field repair from $10,000 to $50,000.

Alternative Septic Systems Cost

When you have a tiny property, a high water table, high bedrock, poor soil, or just wish to utilize less space, an alternate septic system is a good choice.

Mound Septic System Cost

Installing a mound septic system can cost between $10,000 and $20,000 dollars. In places with high water tables, thin soil depths, or shallow bedrock, this is the most costly system to build; yet, it is frequently required. In order to create a drain field, it uses a raised mound of sand rather than digging into the soil. Its extra cost is a result of both the additional technology required to pump sewage upward into the mound and the materials and labor required to construct the mound in the first place.

Recirculating Sand Filter Septic System Cost

Sand filter septic systems range in price from $7,500 to $18,500. They can be built above or below ground depending on the situation. In order to disperse the wastewater in the ground, they employ a pump chamber to force the wastewater through a sand filter. The liner of the filter box is normally made of PVC. This is accomplished by pumping the effluent through the sand and returning it to the pump tank, where it is then disseminated throughout the ground.

Drip Septic System Cost

Drip systems range in price from $8,000 to $18,000, depending on the size and complexity. They operate in the same way as previous systems, with the exception that they employ extensive drip tubing and a dosage mechanism. They deliver lower dosages over a shorter period of time, which is particularly effective at shallow soil depths. This method is more expensive than a standard system since it requires a dosage tank, a pump, and electrical power to operate.

Evapotranspiration System

Evapotranspiration systems range in price from $10,000 to $15,000 per system. In order to allow the liquid to evaporate from the top of an open-air tank, they employ a novel drain field configuration. They’re only usable in dry, arid areas with little rain or snow, thus they’re not recommended.

Built Wetland System

Built-in wetland systems range in price from $8,000 to $15,000, with the cost increasing if an aerobic tank is included. They are designed to simulate the natural cleaning process observed in wetland ecosystems. After traveling through a wetland tank, where it is treated by microorganisms, plants, and bacteria, it is returned to the soil. The waste also has the effect of assisting the growth of wetland plants and the population of microbes.

Chambered System

Installation of chambered systems ranges from $5,000 to $12,000 dollars. They employ plastic perforated chambers surrounding pipes, which are frequently laid in sand, to keep them cool. Gravel is no longer required as a result of this. They are quick and simple to install, but they are more subject to crushing pressures, such as those caused by automobiles.

Septic Tank Replacement Cost

The cost of replacing a septic tank ranges from $3,000 to $10,000. From 30 to 40 years, you may anticipate your system to serve you well. The system may crack or corrode as a result of the failure and the resulting contamination of groundwater with toxic waste is an issue. When this occurs, the well water may get polluted, the yard may become marshy, and the septic system may become inoperable or fail completely. Here’s a breakdown of the various components of a septic tank, along with an estimate of their usual costs: Replacement of a septic tank pump costs between $800 and $1,400.

See also:  What Is The Hourly Rate A Septic Tank Will Drain? (Solution)

Replacement of the filter costs between $230 and $280.

Replacement of a tank lid costs between $30 and $70. Drain Field Replacement Cost: $7,500. When replacing an aerobic system, talk to your service expert about the advantages, disadvantages, and expenses of upgrading to a more efficient aerobic system.

Septic System Maintenance Costs

It is essential that you pump and clean your septic tank at least once a year. In addition, you should get it examined at least once every three years. The proper maintenance of your septic tank will save you money in the long term, and it will also help you avoid potentially hazardous situations. The Environmental Protection Agency (EPA) suggests the following steps to keep your septic system in good working order:

Inspect and Pump Your Septic Frequently

Typically, the cost of septic tank pumping runs from $300 to $550, or around $0.30 per gallon – most septic tanks have capacities between 600 and 2,000 gallons. Every three to five years, you should have your septic tank inspected and pumped by a professional. If you have a bigger home (with more than three bedrooms) and you tend to use a lot of water, you should try to get it pumped at least once every three years. An checkup of a septic system might cost anything from $100 to $900. Your septic inspector will do a visual inspection of the system.

  • Initial inspection costs between $250 and $500
  • Annual inspection costs between $100 and $150
  • And camera inspection costs between $250 and $900.

Use Household Water Efficiently

A toilet that leaks or runs continuously might waste as much as 200 gallons of water per day, although the average family consumes just 70 gallons of water. Take, for example, high-efficiency toilets, which consume 1.6 gallons or less of water every flush or less. The use of new, high-efficiency washing machines and showerheads can also help to reduce water waste, which will relieve the load on your septic system.

Properly Dispose of Your Waste

Your septic system is responsible for disposing of everything that goes down your drains and toilets. One easy rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless it is absolutely necessary. That implies you should never flush the following items down the toilet or drop them down the sink drain:

  • Cooking grease or oil, baby wipes or wet wipes, dental floss, diapers, feminine hygiene products, cigarettes, cat litter, and paper towels are all examples of items that fall into this category.

Maintain Your Drainfield

The drainfield of your septic system is a component of the system that eliminates waste from the septic’s liquid. You should take steps to keep it in good condition, such as:

  • Never park or drive your vehicle on your drainfield. Don’t ever put trees near your drainage system. Maintaining a safe distance between your drainfield and roof drains, sump pumps, and other drainage equipment
Get in Touch With Septic Tank Installers Near You

A septic tank or septic pump tank can range in price from $350 to $14,000, depending on the material used and the size of the tank. In most home situations, you won’t have to spend more than $3,000 on the tank’s actual construction. The majority of big, high-priced units are intended for use in apartment buildings or as part of a communal sewage system.

Concrete Septic Tank Cost

Concrete tanks range in price from $700 to $2,000. The total cost of installation ranges from $2,300 to $6,500. They’re one of the most often seen forms of installation. Despite the fact that they are vulnerable to cracking and separation, they are often resilient for several decades.

It’s critical to have it carefully inspected on a regular basis for cracks and runoff, among other things. Inspections and frequent cleanings will assist to extend its useful life. Your professional can tell you how frequently you should get it inspected, but it’s normally every one to three years.

Plastic and Poly Septic Tank Prices

Septic tanks made of plastic range in price from $500 to $2,500 on average, not counting installation costs. Plastic is a long-lasting, lightweight, and reasonably priced building material. They do not break as easily as concrete and do not rust. Because of their small weight, plastics are more susceptible to harm during the installation process.

Fiberglass Septic Tank Prices

Fiberglass septic tanks are typically priced between $1,200 and $2,000, not including installation. Fiberglass does not split or rust readily, but it is prone to damage during the installation process, much like plastic. However, because of its lighter weight, it is more prone to structural damage, and the tanks themselves can move in the soil.

Steel

It’s unlikely that you’ll ever see a new steel tank constructed. They will rust or corrode with time, no matter how well-made they are at the time. As a result, they are not permitted by many municipal construction rules, and you will only encounter them in existing installations. Steel is not a long-lasting material in the earth, and it is the least preferred.

Labor Costs to Install a Septic System

The cost of labor accounts for 50 percent to 70 percent of your overall expenses. Labor is typically more expensive than the tank itself in a normal installation, making it the most expensive option. For example, while the size required for a 3 to 4-bedroom home may cost between $600 and $1,100, the labor to install it might cost anywhere between $1,500 and $4,000.

Compare Quotes From Local Pros

Here is a breakdown of how much septic tanks cost in different parts of the country. Massachusetts:$9,700 California:$4,500 Florida:$5,300 Texas:$8,000 $5,600 in New York City Colorado:$7,800 Idaho:$10,000

DIY vs. Hire a Septic System Pro

The installation of a septic system is a time-consuming operation. An incorrectly fitted unit can result in water contamination, structural damage to the property, and the need for costly repairs. In addition, an unpermitted installation might make it harder to sell and insure a property when it is completed. Make a point of interviewing at least three pros before making a final decision. Contact a septic tank installation in your area now for a free quote on your job.

FAQs

A septic tank has an average lifespan of 20 to 30 years, however it may live anywhere from 14 to 40 years, depending on the following factors:

  • What it is made of is a mystery. Concrete tends to require more care, but commercial-grade fiberglass and plastic are known to survive for decades in most environments. It’s amazing how well you’ve kept it up. Every one to three years, have your system inspected and pumped out
  • Every three to five years, have it pumped out. It will depend on whether or not it gets vehicle traffic over the leach field. Driving over the leach field compresses it, which increases the likelihood of it failing. The soil’s chemical makeup is important. The length of time it may endure varies depending on the soil type and depth.

What are the signs I need a new septic tank?

There are a few indicators that it is time to replace your septic tank. These are some examples: If you smell sewage, you may have a solid waste problem in your septic tank that has to be dealt with immediately. Standing water: If there is no clear explanation for standing water, such as a significant rainstorm, it is possible that you have an oversaturated drain field, a damaged pipe, or a faulty septic system. A clogged septic tank will cause pipes to drain more slowly than they would otherwise be.

Construction on your home or the addition of more occupants will have an impact on your septic system.

pollution of nearby water: A septic tank leak can result in wastewater contamination, which can deposit nitrate, nitrite, or coliform bacteria in water sources around your property as a result of the leak.

If these bacteria are discovered in your vicinity, you should investigate your septic system to determine if it is the cause. Old age: If your septic system has reached the end of its useful life, it is time to replace it.

Does homeowners insurance cover septic systems?

Many unforeseen and abrupt repairs to septic tanks are covered by homeowners’ insurance policies. They do not, however, often cover harm caused by a failure to perform routine maintenance. Make certain that you are pumping and cleaning it on a yearly basis.

How much do septic system repairs cost?

Repairing a septic system can cost anything from $600 to $3,000. Most tank repairs and replacement parts cost less than $1500 for each type of repair or replacement part mentioned below. Leach fields range in price from $2,000 to $20,000.

  • Tank Pumps cost between $800 and $1,500. A septic tank that is placed below the drain field may necessitate the installation of a pump to transport wastewater to the drain field. Pumping costs between $300 and $600 per year. Pumping is required to remove solid waste from even a perfectly functioning system every two or three years, even if it is in good working order. Tank Lids cost between $100 and $300 to purchase and install. If you purchase the lid and attach it yourself, it will cost you between $50 and $150
  • Tank Lid Risers range in price from $300 to $1,000. Deeply submerged tanks can have their lids raised to the surface by using these devices.
Still Have Questions About Septic Tanks?

If you have never actually lived on your own in a home before, you may not realize the significance of septic tank replacement in Augusta until it is too late. The majority of individuals in Augusta, particularly those who have spent the most of their life in high-rise buildings, are only vaguely aware of the necessity for a septic system. The septic tank is an essential feature of any household, and without it, you will find it difficult to do even the most basic tasks such as flushing the toilet or draining water from the kitchen sink.

Fair price breakdown

In many cases, the cost of Augusta septic tank installation will be determined by a variety of factors. You should consider the size of your home as one of these factors. The greater the size of your household, the greater the amount of money you will have to spend in order to have the system put in your home. You may also hire a professional to visit to your location and assess the type of installation that will be required; from there, they will be able to provide you with an estimate of the prices that you can expect to pay.

Find the Best Costs on Septic Tank Installation – Augusta, 30901

You should also consider other factors that will be important to you, such as whether or not you will use a trash disposal unit and whether or not the laundry water that you use in the house will have to travel through the septic system in Augusta. These are the kind of considerations that will ultimately decide the size of the septic system that will be required in your property. Aside from that, they will also aid you in selecting the most ideal contractor to assist you with the procedure, which will have an impact on the overall cost of the job as well.

Richmond County Septic Tank Installation FAQ

In order to keep your septic system in good working order in Augusta, the first thing you must do is hire an experienced professional to assist you. They must inspect it on a regular basis and arrange pump outs. Additionally, they must ensure that there are sufficient bacteria present to aid in the breakdown of organic materials present in the septic tank system. a. As far as is practical, this should be done once every month. If you fail to do so, you may experience system discomfort as a result of your septic system’s inability to perform the functions that it is designed to do.

The installation of a successful septic tank in Augusta is only the first step in ensuring that your home is equipped with a reliable system. You will, however, require the services of a professional to flush the system on a regular basis. The rationale for this is to ensure that sludge does not build up at the end of the septic tank’s discharge pipe.

If sludge is not cleaned, it will continue to accumulate and eventually fill the filter bed. Soon, your septic system may no longer be able to operate correctly, and it may be necessary to spend a significant amount of money to restore it to working order.

From the minute your Augusta septic tank installation is completed, you must be extremely concerned with the system’s overall functioning. You’ll be able to identify signs of distress and seek professional help to cope with them efficiently in the future in this manner. System backups, gurgling sounds from the plumbing, and poor drainage in the sink and toilet are just a few of the frequent indicators of trouble that require immediate attention from a professional. The most recent update was made on November 28, 2021.

See also:  How Long Can You Depreciate A Septic Tank On Nonrental Property? (Perfect answer)

Local prosAvailability

Plumbers are readily available in your neighborhood.

Applegate Company The

  • 34.810 Technology Dr. Augusta, GA30907
  • 34.810 Technology Dr.

Avrett Plumbing Company

  • Rating: 932332-A New McDuffie Rd.Augusta,GA30901
  • Address: 932332-A New McDuffie Rd.Augusta,GA30901

Augusta Plumbing Inc

  • 81121 out of a possible 100 Lisa Ct.Martinez, GA30907
  • Lisa Ct.Martinez

All Terrain System LLC

Medium: Averages $2,000-$5,000; Runs $4,000-$12,000 in Higher Cost Areas Enhanced System: $10,000-$20,000+
For homes that aren’t connected to a municipal sewer plant, a septic is an on-site system that collects, treats and disposes of household wastewater by slowly filtering it through underground soil. Typically there are two main parts, a septic tank and a soil absorption system (also called a drainfield, leachfield or disposal field). These are located underground and connected to the house by sewage pipes.Typical costs:
  • The cost of installing or rebuilding a traditional septic system (including the tank) is from $2,000 to $5,000 in the Midwest, but can range from $4,000 to $12,000 or more in locations with higher material and labor costs. Septic systems that are designed, engineered-like or alternative septic systems, such as mounds, soil/peat filters, aerobic systems, and/or artificial wetlands, can cost $10,000 to $20,000 or more, according to the Rhode Island Regional Water Quality Program. These alternative septic systems perform better than the conventional technique in areas with high groundwater levels or soil that is slowly or fast percolating, as well as in areas near drinking water supplies, wetlands, coastal ponds, or other water resources. Simply installing a septic tank will cost between $500 and $1,800 based on its size (varying from 300 to 1,000 gallons) and kind. It costs an additional $100-$200 to purchase piping and other necessary supplies
  • New Mexico State University gives an overview of the septic tank installation process. Many locations, however, require that a septic system be planned and constructed by experienced and licensed experts
  • For more information, contact your local or state sanitation agency.

Related articles:Septic Tank Cleaning,Sewer Line Replacement,Replacing Copper Pipes What should be included:

  • It is necessary to employ Septic systems when sewage treatment plants are not accessible, which is typically the case in rural or suburban areas with big lots. Essentially, a septic tank is a huge, underground, waterproof container that can be constructed of concrete, fiberglass, or plastic (polyethylene). An explanation of how septic systems function and where they might be utilized can be found at the North Carolina State University Ag Extension
  • Installing or replacing a septic system might take anything from a few days to a week or more. The procedure entails substantial excavating, which is frequently accomplished using powerful earth-moving equipment.
  • The majority of counties and states require a construction permit for the installation or replacement of a septic system, which may cost anywhere from $250 to $1,000 or more depending on the location and complexity of the job. For further information, contact your local building and planning department. A septic system installation typically entails substantial digging and damage to the landscaping
  • New grass and other plantings can cost anywhere from $100 to $1,000 or more.
  • Unlike individual septic tanks, each house has its own underground septic tank, but all of the septic tanks are connected to a single drainfield, leachfield, or soil absorption system. A cluster septic system, which is often implemented by developers, distributes the expense of drainfield installation and maintenance across a large number of dwellings.
  • To find out if your local sanitation agency maintains a list of licensed septic installation firms, contact them and ask. Onsite wastewater recycling contractors can be found by contacting the National Onsite Wastewater Recycling Association for recommendations. Inquire about training and previous experience. Check to see if the firm is legally bonded, insured, and licensed in your jurisdiction.
CostHelper News What People Are Paying – Recent Comments Page 2 of 2-Previous12
Posted by:Fredbill in Ashland, VA. Posted:October 28th, 2020 10:10AM
Type:PVC pipe

When flushing my toilet during wet weather, it was gurggling and not flowing out properly. Septic company wants to replace old black pipe with PVC pipe running 80 feet from septic tank to distribution box. They think the 65 year-old black pipe is collapsing. Is $37.50 per foot a reasonable price?

Posted by:Fiorella in Miami, FL. Posted:July 28th, 2020 05:07PM
Type:Conventional septic

Septic tank needed repair. House did not have a drain fill. Had one collapsed leg that was installed years back. Repair was done to the tank and an entire drain fill with 5 legs was installed. My house is located in a high water table. I hired a reputable plumbing company that offers a three years warranty. Is this a reasonable price to pay for repairing a septic tank and installing a complete drain fill with 5 legs?

Posted by:Dorie Dew in Nederland, CO. Posted:May 22nd, 2020 02:05PM
Type:leach field install

I am being told that because of county planning dept regs and not enuf “soil” (4 ft) before bedrock here in the Rockies, it will cost $40,000 to install a septic system for a 2 bedroom home (the smallest unit). Please tell me there is an alternative!

Posted by:in Stone Mountain/atlanta, GA. Posted:September 9th, 2019 04:09PM
Type:New system

1000 gallon septic tank with 195 feet of quick 4 plus high capacity infiltrator per county code. Inlet line from house to tank plumbing with level 3 soil test and permit. By Easy Clean Septic 678-532-1276 Easycleanseptic.com

Posted by:in Stone Mountain/atlanta, GA. Posted:September 9th, 2019 04:09PM
Type:New system

1000 gallon septic tank with 195 feet of quick 4 plus high capacity infiltrator per county code. Inlet line from house to tank plumbing with level 3 soil test and permit.

Posted by:Gregory Chappel in Trinidad, CA. Posted:August 15th, 2019 01:08PM
Type:New tank and drain field

1500 gallon tank, 4″line, 90′ rock trenches took 3 days

Posted by:Unclebob in McArthur, CA. Posted:January 26th, 2019 09:01AM
Type:Trailer park

I fought septic tank, leach field problems for years. this is a trailer park, with 35 trailers going into a 7500 gallon tank with 1000 feet in length of leach field. The killer was cooking oil and grease. Plugged up the leach field. Educating the tenants made a huge difference. Then I found the magical cheap combination that worked much better than those expensive enzymes.Equal parts, Yeast, Brown Sugar, and Baking soda. I mix a pound of each and flush it down a toilet every couple of months.

Sams club and Costco sell it in bulk cheap.

Posted by:a user in moreland, GA. Posted:July 20th, 2018 12:07AM

That seems like a lot of money for s single drain line

Posted by:Sfr Development LLC in Boone, NC. Posted:August 11th, 2017 12:08PM
Type:Conventional 2 Foot Chambers

1000 gallon tank. In Mountains Boone NC. Have 30 inches to 48 inches of soil. 3 – 60 Feet 2 foot chamber lines

Posted by:rrrr in berlin, NJ. Posted:July 12th, 2017 02:07PM
Type:septic

location-south jersey-sandy soil approx cost please? looking for economy and conformity.

Posted by:Any Help Appreciated in Charleston, SC. Posted:May 12th, 2017 08:05AM

Getting ready to purchase a piece of land that requires a septic system in order to build. From soup to nuts, (permits, materials, installation) what should I be looking at for total cost? This house will be built very close to water(Charleston, SC less than.5 miles) How long does the process typically take? Any and all help truly appreciated

Posted by:Ken Carbaugh in Leesburg, VA. Posted:June 20th, 2016 06:06PM
Type:conventional to alternative systems

A perc or perk test in Northern Va from a licensed consultant will cost between 1200-2500 dollars depending the district and county fees. Fairfax County costs are 2-4x as much due to local health dept bureaucracy and redtape requiring a surveyor and engineer to be used for any certification or permitting. Real costs of conventional systems (3-4 bedrooms) are from 14-25k depending on the soil percolation results and whether or not a pump is required. If the system is an alternative (BAT in MD) the design costs add 1000-2500 in costs and the installation of the specialized equipment adds costs that can total 20-35,000 easily.

Your property is the most valuable asset you will own so be careful with the land you contract to purchase and beware not all property is equal in value for development.

Posted by:Bob42 in High rolls, NM. Posted:March 25th, 2016 12:03PM
Type:Concrete tank, leachfield

$5500 was the total cost for everything including permits and inspection certificate, tank, pipes, new leachfield etc. I live rurally in a mountainous region with sloping land so more work was required to remediate the land for the leach field to be level. Took about a week from contract signing to completion.

Posted by:Susana in cumming, GA. Posted:August 24th, 2015 04:08PM
Type:treating the leach field

I had a septic company come to do a septic tank pump for $150 but they said I needed a more expensive leach field treatment at a cost of over $2500 even thought there is no back up or smell anywhere.

They wind up doing an enxyme one leaving me with 6 gallons of liquid enzyme I am suppose to pour down the toiled once a month. My son says I was ripped off. Is he right?

Posted by:payed too much? in Effort, PA. Posted:August 2nd, 2015 11:08PM
Type:dual tank w mound

Had Pump replaced as well as wire to house, dug up yard, to replace line, replaced pump, didn’t take garbage, didn’t clean up landscape, pump both tanks included in price, found truck parts in driveway and tanks not pumped, claim truck broke be back to pump.was this a lot, I had to rake out landscape and driveway, clean wires, boxes and garbage left behind,.I hope they pump the tanks soon.

Posted by:Daytrp in Eldersburg, MD. Posted:July 17th, 2015 08:07PM
Type:Repair – new construction

Repair permit: $130-450 depending on county.New construction permits: $250-550.New septic $16-22k for advanced treatment, $8-10k conventional Perc test for repair: $850-$1,400 takes 2-6 hours. Done with county sanatarian onsite. A common septic repair: (installation of 2 – 60′ long x 3′ wide x 8′ deep with 4′ of stone below pipe invert) runs about $6,500.Trench dimensions are determined by number of bedrooms (occupancy) and percolation rates from perc test. price varies depending on Trench size.

Septic tank add $2,500-3,500 Pump chamber, pump and controls add $4,000-5,000.

Some states Have programs to help upgrade your septic tank.

Specailty jobs, difficulty of access, heavy rock, all add to the bid price

Posted by:ABMCCAA in Bakersfield, CA. Posted:June 26th, 2015 05:06PM

New 1500 Gallon Tank, Engineering, 60′ of Leach Field with Rock base drainage system. 50 ton of 3/4″ rock, new 4″ main line to house, soils testing and permits. Took 3 days total.

Posted by:andrewbasil in hemet, CA. Posted:March 23rd, 2015 06:03AM
Type:simple leach line replacement

75 feet of leach line were dug up and replaced the. attached up to original fifteen hundred gallon 1973 concrete septic tank and re buried. they had to knock down two fruit trees and by accident sheared off a water tap. (Having not repaired the water line it has now become a 5 foot stream shooting straight up in air.) I do feel grandmother was taken advantage and charged double of not more for services that. and this is the worst part. a permit nor independent inspection was never done for this job.

Help me out here what do I do?

Posted by:ltodd kinsey in cda, ID. Posted:February 26th, 2015 11:02PM
Type:all

If properly maintained a working system should never need pumped

Posted by:M. IRIARTE in STROUDSBUR, PA. Posted:February 4th, 2015 05:02AM
Type:SEPTIC

ANYONE IN THE POCONOS HAS HAD THEIR SEPTIC SYSTEM REPLACE. WHAT WAS THE COST OF REPLACEMENT.WOULD LIKE TO GET FEEDBACK Page 2 of 2-Previous12 External Resources:

  1. Twri.tamu.edu/reports/1999/l5234.pdf
  2. sohioline.osu.edu/aex-fact/0744.html
  3. s

More Articles on the Subject of the Home and Garden

Check Out All Costs for Home and Garden How Much Does a Kitchen Remodeling Cost? How Much Does a Propane Tank Cost? How Much Does a Plumber Cost?
CostHelper is based in Silicon Valley and provides consumers with unbiased price information about thousands of goods and services. Our writers are experienced journalists who adhere to our stricteditorial ethics policy.

Leave a Comment

Your email address will not be published. Required fields are marked *