Where To Buy Septic Tank Lids?

  • Go online and you should be able to find a few retailers that offer them in your area. The professionals who work on septic tanks in your area may also offer their own replacement lids. You can also choose from a wide selection of replacement lids.

Can you replace the lid on a septic tank?

Concrete septic tank covers require replacement when they develop cracks or other damage. These can be purchased online or at a home improvement store near you. Many septic tanks have risers so the lid is visible above ground.

What can I use as a septic tank lid?

The Do’s For Hiding Your Septic Tank

  1. Plant tall native grasses with fibrous roots around the opening to conceal the tank lid from view.
  2. Place a light statue, bird bath or potted plant over the septic lid.
  3. Septic tank risers and covers are an alternative to concrete and blend into green grass.

What sizes do septic tank lids come in?

Available in 12″, 16″, 20″ and 24″ diameters. Green only. 12″ Tall Riser – For septic tanks.

How much does it cost to replace a lid on a septic tank?

Over time, concrete covers may crack, and steel lids may rust. You can typically replace a septic tank lid on your own for $35 to $60.

How do you lift a septic tank lid?

Some tank lids have built-in handles to pull on, but others require a pry bar to lift them open. If the lid comes with handles, ask for the assistance of a friend or family member to remove the lid. If it doesn’t, push a screwdriver into the seam around the lid and insert the pry bar into the gap. Then, press down.

Why does my septic tank have 2 lids?

Solid, watertight, buried tank made of concrete, plastic, fiberglass or metal. This tank has a way in (inlet), and a way out (outlet). So, most residential tanks should have (2) lids about 5′ away from each other. A septic tank holds all the liquid waste from your home (toilets, sinks, kitchen, bathtubs, floor drains).

How heavy is a septic tank lid?

The concrete covers also weigh 60 – 80 lbs. Because of the weight, many people are discouraged from removing the cover and doing an inspection. Modern plastic septic tank riser rings typically weigh less than 30 pounds.

Do all septic tanks have two lids?

A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

How do you know when your septic tank needs to be pumped?

Common Signs You Need Septic Tank Pumping Services

  1. Slow or Frequently Clogged Drains. Since your septic tank is connected to the entire network of drains throughout your home, your sinks, showers, and even toilets can exhibit signs of a problem.
  2. Sewage Backup.
  3. Regular Gurgling Noises.
  4. Strong and Pungent Odors.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

What are the 3 types of septic systems?

Types of Septic Systems

  • Septic Tank.
  • Conventional System.
  • Chamber System.
  • Drip Distribution System.
  • Aerobic Treatment Unit.
  • Mound Systems.
  • Recirculating Sand Filter System.
  • Evapotranspiration System.

How long does a leach field last?

It’s important to consider the life expectancy of a drain-field, too. Under normal conditions and good care, a leach-field will last for 50 years or more. Concrete septic tanks are sturdy and reliable but not indestructible.

Septic Tank Risers, Lids, and Covers

Septic tank risers are intended to replace existing concrete, fiberglass, or metal septic tank lids by lowering the entrance to the ground level and allowing for better drainage. Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.

With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!

Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water?

It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.

With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!

FREQUENTLY ASKED QUESTIONS

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered! Would the POLYLOK SEPTIC TANK LID fit directly on the ADAPTER RING, or will I need to use a RISER to ensure a proper fit on the tank? With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength.

  • Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter.
  • ALL other Polylok lids will attach straight to the adapter ring, eliminating the need for a riser or any other adaptor.
  • No.
  • Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.
  • It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade.
  • IS IT BETTER TO USE THE STANDARD LID OR THE HEAVY DUTY LID?
  • If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended.
  • Yes.

IS IT INCLUDED WITH THE POLYLOK SEPTIC TANK RISERS AND LIDS TO USE SCREWS? Yes. The Polylok Septic Tank Risers are assembled using stainless steel screws that allow them to be connected to one another. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].

THE POLYLOK SEPTIC TANK RISER ADVANTAGE

Riser systems are available in a variety of shapes, sizes, and designs on the market today. The Polylok septic tank risers are, without a doubt, the best money can buy in this category. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

The Polylok risers are reinforced with structural ribs that run internally around each riser segment, providing them with exceptional strength and allowing them to maintain their shape even after the hole is backfilled with dirt. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

LOW PROFILE RISER LIDS WITH HANDLES

The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE TANK ADAPTER RING

It is necessary to use an adapter ring in order to attach risers to your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

STAINLESS STEEL SCREWS INCLUDED

At Septic Solutions, we strive to make the buying and installation process as simple as possible for our customers. All of our Polylok risers and lids are delivered with all of the stainless steel screws required for installation in one package.

Amazon.com : Septic Tank Covers

THE RESULTSPrice and other information may differ depending on the product size and color selected. SubscribeSave allows you to save even more money. Created with Sketch. Sponsored You can have it as soon as Monday, February 14th. Shipping is $9.30. Ships to the Netherlands are available. There are only 10 left in stock, so place your purchase now. Ships to the Netherlands are available. There are only 2 left in stock (more on the way). Ships to the Netherlands are available. There are only 2 left in stock (more on the way).

  1. With the coupon, you may save 6 percent.
  2. There are only 12 left in stock, so place your purchase now.
  3. SubscribeSave allows you to save even more money.
  4. At the time of purchase, a $5.00 coupon was added.
  5. Ships to the Netherlands are available.
  6. With the SubscribeSave discount, the price is $19.77.
  7. With the coupon, you may save 5 percent.

At the time of purchase, a $1.00 coupon is applied.

It’s yours.

At the time of purchase, a $5.00 coupon was added.

Only 18 units left in stock – purchase soon.

There are only 10 left in stock, so place your purchase now.

With the coupon, you may save 6 percent.

Only 6 of these items are left in stock – purchase soon. There is a deal available for 10% off. Ships to the Netherlands are available. There are only 10 left in stock, so place your purchase now. Brands that are associated with your search

Amazon.com: Tuf-Tite 20″ Heavy Duty Flat Lid – Septic Tank Lid – Septic Tank Cover : Sports & Outdoors

On March 28, 2021, a review was published in the United States of America. The “manhole” in front of the home is well-protected. Color-wise, it is a good match for the surrounding flora. It’s quite durable and has a substantial weight. This is a very well-made product. Added to review on September 29, 2021 in the United States of AmericaVerified Purchase It is a perfect fit for the riser tube. The finished assembly can handle a lot of weight, and I wish I knew how much. On June 22, 2020, a review was published in the United States of America.

  1. This allows the mower to travel over it without any problems because it is flat and level with the ground.
  2. Nonetheless, it is an excellent replacement choice.
  3. Although it takes a long time to arrive, it is effective.
  4. The product was reviewed in the United States on September 3, 2019 and was verified to be genuine.
  5. On June 7, 2021, a review was published in the United States of America.
  6. Excellent overall quality.
  7. It is of high grade.
  8. Originally published in the United States on July 3, 2017Verified Purchase With a lawn mower, I appreciate the flat structure since it makes it easier to zip over cover!
See also:  What Is A Septic Pump Tank? (Question)

Best Price on Septic Tank Risers & Covers Online Guarenteed!

Septic Tank Risers and Lids are available from TGWasteWater in a variety of sizes and styles. We also provide a large selection of accessories for our riser products. Are you fed up with having to pay to have your system dug up and pumped every time it needs to be refilled? Are your present concrete risers at danger of collapsing? Is it becoming tiresome to have to lift a hefty concrete cover every time you need to access your tank? It is possible that you responded yes to any of these questions and that you should think about putting a riser system on your septic tank.

Risers from Tuf-Tite and Polylok are available for purchase.

Please keep in mind that Tuf-TitePolylok products are incompatible with one another.

Consequently, if you want us to utilize a Tuf-Tite lid, you must purchase Tuf-Tite Risers, and the reverse is true. Do you have questions about how to build a riser on a septic system? PLEASE CLICK HERE TO READ OUR INSTRUCTION GUIDE ON HOW TO INSTALL RISERS ON A CONCRETE SEPTIC TANK

Acton Precast Concrete Limited

Name Length Width Height lbs. Price
2’x4′ Septic Tank Lid – no m/hole 48″ 24″ 4″ 340 $ 210.00Add To Quote
4’x4′ Septic Tank Lid – c/w 1 m/hole 48″ 48″ 4″ 680 $ 280.00Add To Quote
4’x8′ Septic Tank Lid – c/w 2 m/holes 96″ 48″ 4″ 1350 $ 460.00Add To Quote
Lid to fit our 800 S/T600 P/C 96″ 62″ 4″ 2000 $ 500.00Add To Quote
Lid to fit our 10001200 Gal Septic Tanks 120″ 68″ 4″ 2500 $ 525.00Add To Quote
Round Concrete Septic Tank Lid 29″ dia. 4″ 150 $ 50.00Add To Quote
Manhole covers for our old tanks 21″ 21″ 4″ 100 $ 44.00Add To Quote
Concrete manholes custom sized $ 125.00Add To Quote
Galvanized lockable hinged cover 24″ 24″ 8″ $ 750.00Add To Quote

Best Septic Tank Risers & Lid Replacements ⋆

Lawn mowers and other lawn and garden devices can cause significant damage to septic tank risers and lids, which can result in costly repairs. Although most sewage tank risers and lids were formerly made of exceptionally durable concrete, green plastic is now being used as a less expensive and easier to install alternative to concrete in most cases. Sewage lid security is vital because it stops animals from accessing the septic system and also helps to avoid accidents from occurring. The sewer covers also protect the septic grinder pump, filter, and other mechanical components from damage caused by the weather, including hail, ultraviolet radiation, floods, and other elements.

When selecting a septic riser or lid, it is critical to consider durability, ultraviolet (UV) protection, and weather resistance.

Top Rated Septic Tank LidsRisers

1. Polylok 3008-RC Riser with a 24′′ diameter. It is necessary to utilize this product in conjunction with Polylok 3008 or 3008-R12 risers. The high-density polyethylene (HDPE) construction allows it to survive the severe climate found within the septic tank. Gaskets have been put on the lid to improve the overall quality. Because certain of the chemical components in the product are known to create cancer-related hazards, you should exercise caution when handling it. This model also has the following features:

  • The use of HDPE in the design is beneficial. Installed to improve the overall quality
  • Installation is quick and simple. Simple to clean and keep up to date

High-density polyethylene (HDPE) construction is advantageous. Improved quality was achieved by the installation. Installing the software is quick and simple. Maintainability and cleaning are not a problem;

  • The use of HDPE in the design is advantageous. Installed in order to improve the overall quality
  • Installation is quick and simple
  • It is simple to clean and maintain

The use of HDPE is advantageous. Installed in order to improve quality; Installation is simple and quick. Simple to clean and maintain;

  • Corrugated pipes are an excellent choice. It has a watertight seal
  • There is no O-ring fighting
  • It is simple to maintain.

Our Score: (4.5 out of 5) GET THE LOWEST PRICE! 4. Polylok 3008-HD24 (high-density polyethylene). Lid with a lot of strength The cover is designed to fit any 24′′ ribbed or corrugated pipe with ease. The cover is made of a robust material that is both airtight and waterproof. Aside from that, it boasts one of the most comprehensive UV packages available on the market. Because of its HDPE construction, it is resistant to the extreme weather conditions seen in the septic environment. This raises the level of protection you have.

  • Compatible with ribbed pipe
  • The strongest and most lasting
  • Resistant to adverse weather conditions
  • Increases your safety

(We give it a 5 out of 5) GET THE LOWEST PRICE! Jackel Riser Cover (number 5) This cover is ideal for 18′′ diameter riser pipes, whether they are made of PVC, double wall polyethylene, or single wall polyethylene. It is available in a green hue, which allows it to blend in with the surrounding environment. It’s long-lasting, lightweight, waterproof, and replaceable in the event of a failure. This model also has the following features:

  • The most suitable option for polyethylene pipes
  • It has a green hue to it. It is both long-lasting and lightweight. It is simple to replace

Our score is a (4/5) GET THE LOWEST PRICE! Septic Tank Risers of the Highest Quality If you’re looking to purchase septic tank risers, the following are the top five options available to you. 1. A total of 24 x 12 Tuf-Tite Risers The product has a diameter of 24 inches and a height of 12 inches. The screws used in the cosmetics are made of stainless steel, which increases your safety. It is available in a green tint that blends in well with the surrounding surroundings.

The pattern is available in four different diameters: 24 inches, 20 inches, 16 inches, and 12 inches. The HDPE construction also makes it more resistant to the severe conditions of a septic system. This model also has the following features:

  • 24′′ in diameter and 12′′ in height
  • Stainless steel is used in its construction. It is available in the color green. Available in four different diameters: 24 inches, 20 inches, 16 inches, and 12 inches.

(We give it a 5 out of 5) GET THE LOWEST PRICE! 2. AS-R23 Riser Kit (included). It’s the new industry standard design for the time being. In addition to the safety obstacles, a sealant, a protective cover, and the installation instructions are included. The given item is complete and ready to be installed. Because of its design, the Aero-Stream Remediator can be installed in less time and with less difficulty. This model also has the following features:

  • New standard design
  • A variety of safety obstacles
  • And a new standard design. Prepared for installation
  • Design makes things more efficient and easy

Our score is a (4/5) GET THE LOWEST PRICE! 3. Riser Kit for the AS-R32 The AS-R32 Riser Kit is an enhanced version of the AS-R23 Riser Kit. It is delivered with a plastic adaptor that is 29′′ x 29′′ in size. It is pre-configured for direct installation, and its installation makes the installation of Aero-Stream Remediator more efficient and straightforward. It also includes a comprehensive set of installation instructions. This model also has the following features:

  • This item comes with a plastic adaptor. The item measures 29′′ x 29′′. Installation without a hitch
  • Installation makes the process more efficient and straightforward.

(We give it a 5 out of 5) GET THE LOWEST PRICE! 4. Tuf-Tite 20′′ x 12′′ Riser (optional). The Riser is 12 inches in height and 20 inches in diameter. It is suited for use with septic tanks, and the stainless steel screws used in its construction boost its overall efficiency. It is available in four different diameters: 24 inches, 20 inches, 16 feet, and 12 inches. It is available in a green tint that blends in wonderfully with the surroundings. This model also has the following features:

  • Septic tanks are suitable for use. Available in 24′′, 20′′, 16′, and 12′′ diameters
  • Green in color
  • Completely fits

Our score is a (4/5) GET THE LOWEST PRICE! 5. As-R07 Riser Kit (optional). The product has a diameter of 24 inches and a height of 7 inches. It is sent fully assembled, with an instruction manual included for your convenience. Its setup makes it simple to install Aero-Stream Remediator more quickly and easily than ever before. This model also has the following features:

  • It has a diameter of 24 inches and a height of 7 inches. Finished and ready to be installed
  • Please see the attachment for the instruction manual. Installation makes the process more efficient and straightforward.

Our Score: (4.5 out of 5) GET THE LOWEST PRICE! In order to maintain environmental cleanliness and human health, septic tanks are essential. They assist in the disposal of human waste, which, if not managed properly, can result in a variety of ailments. Every septic tank requires a riser and a lid in order to function properly. If you’re thinking of purchasing one, have a look at the information in this post to ensure that you make an informed decision. What is a septic tank riser and how does it work?

  1. When it comes to the new models, it is a collective advancement, but the earlier designs are missed opportunities.
  2. As a result, the cleaning firm will not be required to dig into the ground in order to reach the storage tank.
  3. A septic tank lid is a cover that is used to shut the top of the tank riser.
  4. The cleanout business installs it at the top of the riser so that it may be used to determine the tank’s perimeter.
  5. Reasons for the need for a replacement You will eventually need to repair both the septic tank riser and the septic tank lid.
  6. The lid or the riser may also need to be replaced if you decide to rebuild your septic tank from scratch.
  7. In most cases, replacing the top will cost you roughly $70, while replacing the riser will cost you at least $150.
  8. The following are some of the most effective septic tank riserslid replacement options to consider.
  9. Keeping your septic tank in excellent working order is a good habit to get into.
  10. Consequently, it’s critical that you inspect the walls, the riser, and the lid for any fractures that may exist before proceeding.

If there are any indicators, you should consider having them replaced as soon as possible. SummaryReviewer Jack Ryan is a fictional character created by author Jack Ryan. Item was reviewed on the date specified in the review. Septic Tanks RisersAuthor Rating5 out of 5 stars

Septic Tank Riser Kits – Wholesale Septic Supply

Are you fed up with having to dig up your septic system every time it has to be repaired or serviced? If this describes you, we have a fantastic option for you. In order to modify the way you operate on your septic system, you may require a suitable septic riser, which can be found online.

See also:  How Much To Move A Septic Tank? (Correct answer)

Why choose Tuf Tite Risers?

The Tuf Tite Septic Riser System allows you to get access to your outside septic system in a quick and simple manner. With the help of this revolutionary instrument, septic system service becomes a snap, and you will never have to dig up your septic system again! This system eliminates any guessing by providing you with the riser and other components you require to complete the task. Because you are ordering all of the essential parts in a single package, you will save both time and money on the installation process.

What are the Tuf Tite Product Specs?

Every riser system is simple to install on concrete septic tank lids, and the kit will even tell you what size access hole will work best with your septic system based on the information in the kit. The riser system is effective on 95 percent of septic systems with round diameter entrances ranging from 16 inches or less to 25 inches or less, and square sizes ranging from 11 inches by 11 inches to 18 inches by 18 inches. Looking for high-quality products? Look no further than this store! There are several sizes available for the Tuf Tite riser system, which has been engineered to last.

  1. Septic tanks are normally installed below the surface of the earth.
  2. Installing a riser kit is the most effective approach to deal with this issue.
  3. When the riser comes into contact with the tank, an adapter ring should be used to seal the connection.
  4. A number of risers will be stacked on top of each other and the adapter ring until they reach the ground level, at which point they will be removed.
  5. This method will establish a barrier around the tank, protecting it from contamination while also making access to the tank more convenient.
  6. In order to ensure that the circular riser will fit around your square or rectangular access port, there are a few things you may do.
  7. The diagonal distance across the access will be the longest distance that a riser will have to cover before it may be used.
  8. Assume that “a” is the length of one side of the port’s access.
  9. For example, A is 12 inches in length and B is 12 inches in length.
  10. The equations shown above can be used to estimate the diagonal distance of a rectangle in a rectangular coordinate system.
  11. The only risers that should be utilized are those having an inner diameter that is bigger than the diagonal distance between the access port and the wall.

This approach will need the knowledge of the lengths of each side of your rectangular access port in order to work. Pythagorean theorem is something you may remember from your geometry training.

Tuf-Tite Septic Tank Riser Lids – Wholesale Septic Supply

Results 1 – 4 of 4 Total Results Tuf-Tite 20 is a high-performance lubricant “A brief overview of the Tuf Tite 20″ domed septic tank lid: the Tuf Tite 20″ domed septic tank lid is used in conjunction with the Tuf Tite 20″ septic risers. They are the best riser lids on the market today because they are composed of high-density polyethylene (HDPE), which gives them their strength and durability. ***Please note that lids do not come with screws. Overview of the Tuf-Tite 20″ Domed Septic Tank Cover: The Tuf-Tite 20″ domed septic tank lid is used in conjunction with the Tuf-Tite 20” domed septic tank cover “Septic risers are used to raise the level of the septic tank.

  • Tuf-Tite 24 is a high-performance lubricant “Domed Septic Tank Cover Overview: This standard provides protection for septic tanks.
  • They are the best riser lids on the market today because they are composed of high-density polyethylene (HDPE), which gives them their strength and durability.
  • Tuf-tite 24 is a tuft-tite that is 24 inches wide “a dome-shaped structure Tuf-Tite 24 is a high-performance lubricant “Domed Septic Tank Cover Overview: This standard provides protection for septic tanks.
  • The Tuf-.65.00 is the price of the Tuf.
  • They are the best riser lids on the market today because they are composed of high-density polyethylene (HDPE), which gives them their strength and durability.
  • 16″ in circumference Tuf-Tite 16 is a high-performance rubber compound “Septic Ta in a dome.
  • The T.
  • Tuf-Tite 12 is a high-performance rubber compound “A brief description of the Tuf Tite 12″ domed septic tank lid: It is used in conjunction with the Tuf-Tite 12” septic risers to provide a secure seal around the tank.

***Please note that lids do not come with screws. Overview of the Tuf-Tite 12″ Domed Septic Tank Cover: The Tuf-Tite 12″ domed septic tank lid is used in conjunction with the Tuf-Tite 12″ domed septic tank cover “Septic risers are used to raise the level of the septic tank. The T. is $45.00.

Overview

Tuf-amazing Tite’s array of septic tank riser products helps to keep unpleasant odors at bay while also providing a secure cover and easy access for periodic maintenance to the tank’s interior. One of the most appealing aspects of these risers is the large number of configurations from which to pick from. The size and shape of the cover that you wish to install over your septic tank should be taken into consideration when selecting a riser that is appropriate for your requirements. When purchasing a Tuf-Tite riser, you will have the option of selecting one of two different lid forms.

Flat Lids

Many septic tank risers come equipped with a flat lid, which is the most common configuration. These riser covers, which are available in 20″ and 24″ diameters, are designed to accommodate most risers, as well as IPEX-PVC ribbed pipes and corrugated pipe. For installation on your Tuf-Tite septic tank riser, the four stainless steel screws and two vertical safety screws will be included with each lid you purchase. Each lid is manufactured to Tut-high Tite’s standards, resulting in a watertight cover that prevents rainwater or drainage from flowing into your septic system.

Domed Lids

The dome-shaped lids are equivalent to the flat lids in terms of construction quality and water seal protection, as well as in terms of water seal protection. There is a subtle difference in that each domed lid is equipped with six attachment screws in addition to a horizontal safety screw. Domed lids are also available in a greater variety of sizes as compared to flat lids. The diameters range from 12″ to 16″, as well as 20″ and 24″ in circumference. To guarantee that your septic tank is completely sealed, each of these sizes has an integrated gasket and is included with an accompanying Tank Adapter Ring.

How septic tank lids and covers are saving you money – Aeration Septic

A septic tank system may be one of the most expensive mechanical elements on a property, making it one of the most important investments. It is also one of the least thought about or comprehended of all the concepts. It may be tempting to flush it down the toilet and forget about it, but doing so may be quite costly in the long run, since regular maintenance and monitoring can help to avoid pricey repair fees. Risers and lids for septic tanks are an excellent and cost-effective solution to ease future maintenance and monitoring of the tank.

What are septic tank risers and lids?

While your septic tank is located beneath the earth, septic tank risers provide a big diameter “well” that allows for a safe access point to the sewage tank to be located at ground level if necessary. The lid is attached to the top of the riser and is designed to completely encapsulate the system in an airtight and watertight manner. In this way, surface water and debris such as grass clippings, mulch, and soil are prevented from entering the tank. It also helps to keep gases and smells from leaking from the septic system as well.

There are several benefits to septic tank risers and lids

First and foremost, having a clearly visible septic tank lid on the property serves as a pleasant reminder that a septic system is in place. However, whereas older-style concrete coverings were considered to be heavy and unattractive, current plastic lids are lightweight and made to integrate with the surrounding environment. These lightweight variants make it simple and cost effective to install, monitor, and service your septic system, and they are also easy to transport. Savings on expenses By establishing an access point at ground level, service experts will have an easier time locating the septic system for routine maintenance, repairs, or to pump out the septic tank as necessary.

Stainless steel threaded fasteners are used to connect lids to the riser and keep them in place to avoid tampering by minors and potential falls into the septic tank.

The high duty riser and lid systems placed at ground level are sturdy enough to withstand being mowed directly over.

As a result, there is no need to spend the additional time and energy trimming around them.

At Aeration Septic Inc, we provide several different types and sizes of septic tank covers and lids. More information may be found by checking out our collection or by visiting our Amazon shop.

Aeration Septic – Septic Tank Risers and Lids

Septic tank lids, risers, and covers are an excellent method to save time and money while also increasing safety around the septic system and preventing flooding. Installing septic tank lids and risers to bring access to your system up to code can save you the money you would otherwise spend on having your system dug up every time it has to be pumped. If you replace heavy concrete lids with lightweight yet sturdy and durable plastic lids that can be attached securely to protect the safety of children and dogs in the vicinity of the system, you may save your back.

Polylok Septic Tank Risers and Lids

12″ x 6″ Septic Tank Riser made of Polylok

  • Extra strength is provided by heavy-duty structural rib reinforcing. For UV-Rays, a green opaque hue is used. Molded warning signs that are clearly visible for safety
  • Frost is prevented from clinging to frost prone locations by structural ribs on the interior.

Riser Lid for Septic Tank with Polylok 12″ Lid

  • Riser Lid for Septic Tank with Polylok 12″

Septic Tank Riser Polylok 20″ x 6″ Polylok Septic Tank Riser

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction. Frost is prevented from clinging to frost-prone locations by structural ribs on the interior.

Septic Tank Riser Polylok 20″ x 12″ Polylok 20″ x 12″

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction.

Riser Lid for Septic Tank with Polylok 20″ Lid

  • The surface is slip-resistant, and it has two recessed handles for simple removal. The most effective UV protection available
  • In order to dissuade unwanted entrance, square drive screws are used.

The Polylok 20″ Heavy Duty Septic Tank Lid is made of polypropylene.

  • Surface that is skid resistant
  • The highest level of UV protection possible
  • It has a foam gasket to provide an airtight and waterproof connection. In order to dissuade unwanted entrance, square drive screws are used.

The Polylok Septic Tank Riser measures 24″ x 6″.

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction. Bring the septic access up to grade in no time
See also:  How To Know Septic Tank Is Full? (Question)

The Polylok 24″ x 12″ Septic Tank Riser is made of polyethylene.

  • Watertight and airtight
  • Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction.

Riser Lid for Septic Tank with Polylok 24″ Lid

  • The surface is slip-resistant, and it has two recessed handles for simple removal. The most effective UV protection available
  • In order to dissuade unwanted entrance, square drive screws are used.

Alternatively, you may phone us at 330-236-1561.

Tuf-TIte Septic Tank Risers and Lids

Tuf-Tite 20″ x 6″ Septic Tank Riser is made of polyethylene.

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite 20″ x 12″ Septic Tank Riser is made of polyethylene.

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite Heavy Duty Septic Tank Lid, 20″ in Diameter

  • Air and watertight connection made possible by a foam gasket
  • Heavy-duty, long-lasting structure

Tuf-Tite Septic Tank Riser (24″ x 6″ x 5″)

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite Septic Tank Riser (24″ x 12″ x 4″

  • Watertight and airtight construction
  • Bring the septic access up to grade in no time
  • Stackable

Tuf-Tite Heavy Duty Septic Tank Lid, 24″ in Diameter

  • A foam gasket is used to ensure an airtight and waterproof connection. Heavy-duty, long-lasting structure
  • Screws made of stainless steel are provided.

Tuf-Tite Domed Septic Tank Lid, 24″ in Diameter

  • Screws made of stainless steel are supplied
  • Two horizontal safety screws are also included.

How to Replace a Concrete Septic Lid With a Plastic Lid

Jupiterimages/Photos.com/Getty Images is the source of this image. In most cases, thick concrete lids over manholes and access holes are used to build concrete septic tanks, which are subsequently covered with soil after installation. While this is a satisfactory installation, many septic specialists recommend that the concrete lids be replaced with plastic risers and lids to provide for easier access to the tank for examining and cleaning the system. The new plastic top is now easily accessible for pumping and maintenance thanks to the addition of a riser.

How to Replace a Concrete Septic Lid With a Plastic Lid

Remove any furniture, potted plants, yard décor, and other things from the surrounding area. Protect your pets, and keep other people and children away from the area. Put on your protective gear as well, such as gloves and safety goggles. When working with concrete, always use a dust mask or a respirator to protect your lungs from the silicates in the dry mix that can cause irritation.

Step 2: Locate the Tank and Lids

Identify the tank and its covers. As a result of the shallower soil and reduced ability to hold moisture for the lawn’s roots, dead grass may be an indication of the tank’s position. A metal detector may be used to discover rebar in concrete tanks, after which it can be probed to locate the edges.

Step 3: Remove the Soil

Remove all of the dirt that has accumulated on top of the septic tank. In most cases, the tank is located between 1 and 3 feet below the surface of the earth and up to 25 feet away from the home, depending on the conditions.

When it comes to dimensions, the typical septic tank is around 4 1/2 feet broad and 8 feet long; however, larger tanks are available. Check for structural damage to the tank as well; cracks or a drooping top signal that repairs or replacement of the tank are necessary.

Step 4: Measure the Lid

Take the diameter of the lids, as well as any tank inlet or baffle outlet covers, and round them up. If the bigger lid, sometimes known as a “manhole” lid, has a diameter greater than 24 inches, it may be necessary to use an adapter before placing the lid riser over the hole. Adapters are available from the company that makes the lid riser.

Step 5: Remove the Lid

Remove the concrete covers from the containers and set them aside. Because the concrete lids are so heavy, it may be necessary to utilize a backhoe to complete this task. It is best not to breathe any of the fumes that are rising from the septic tank and to use a protective mask or respirator to minimize exposure.

Step 6: Adjust the Riser Height

Obtain an accurate measurement of the distance between the tank and the ground. Make any required adjustments to the riser in accordance with the manufacturer’s instructions, or in older systems, consider installing a riser to raise the new lid to ground level. The present riser’s height can be reduced by drilling an appropriately sized hole in it and then trimming the surplus riser length using a jigsaw, as shown in the image below. Some manufacturers create adjustable risers, which eliminates the need for cutting.

Step 7: Rough the Riser Base

Using 40- to 60-grit sandpaper, sand the area around the base of the risers. Place the risers over the manholes, as well as the intake and outflow holes, after wiping them down with a tack cloth.

Step 8: Apply Concrete Patch Mix

In a bucket, combine the quick-drying, high-strength, flexible concrete repair mix that has been advised. Work rapidly, since the mixture will dry in 15 to 20 minutes if left to sit. With a trowel, apply a generous amount of sealant around the bases of the risers, being sure to cover the edges all the way up to the top of the septic tank. Allow for a thorough drying time.

Step 9: Attach the New Lid

Set replacement lids on the risers, following the manufacturer’s instructions and using a socket wrench to secure them in place.

Step 10: Rebury the Tank

Soil should be used to cover the septic tank. Cover the bare soil with sod or grass seed to prevent it from becoming naked.

Tip

  • Inspect and pump the tank (if necessary) while the lids are off
  • This will save you time and money later on. After finishing the activity, thoroughly wash your hands and clothing with soap and hot water to remove any remaining dirt.

Warning

  • You should never enter or even put your head inside a septic tank unless absolutely necessary. Every year, a number of people die as a result of the fumes produced by septic tanks
  • You may pass out, fall in, and suffocate or drown. When the lids of the septic tank are open, never leave the tank alone, even for a single minute. It is possible for a kid or pet to fall in and drown
  • Avoid driving over the risers and lids.

Common Septic Tank Facts

Septic systems are a low-cost and frequently successful alternative to conventional sewer systems. Concrete tanks have been the most frequent since the 1940s, with 3 – 500lids for a 1000 gallon tank and 4 – 500lids for a 1500 gallon tank being the most typical. Tanks began to be equipped with 16″ square concrete plugs with a lifting bail in the late 1990s, allowing for easier access to both sides of the tank. Many tanks today are made of fiberglass or plastic. Over time, the concrete might degrade, and the lids may develop cracks or possibly shatter completely due to the pressure.

  1. Even broken lids should be replaced for the sake of the public’s safety.
  2. They get access to your septic tank by removing green covers that are 20 inches in diameter.
  3. This is done in order to prevent anyone, especially children, from removing a lid and falling into the container.
  4. A typical water level for a tank should be 6″ below the top of the tank, and the tank should be kept completely filled at all times.
  5. The level of the water is often a good sign of potential problems.
  6. Additionally, it might suggest a clogged intake line, which could be caused by roots, a damaged pipe, or a loose joint.
  7. If there has been a lot of rain, the earth may get saturated, making it impossible for any additional water to seep through the soil to the surface.
  8. If your tank has allowed particles to enter the field lines, this might cause the openings in the corrugated pipe to get clogged, preventing water from percolating through the soil as effectively as it should be.

An output filter may be placed to prevent particulates from entering the field lines, but it would need to be cleaned on an annual basis to ensure that this does not happen. Nonetheless, it is far less expensive than rebuilding field lines.

Septic Tanks – Traverse City, MI – Belanger Septic & Security Sanitation

Risers are used on septic tanks to raise the lid of the tank to a safe level. They assist to reduce the expense of pumping a septic tank by eliminating the need to identify and dig up lids on tanks, as well as safeguarding your irrigation and landscaping. Risers are simple to install and may be done by the homeowner, or we can do it for you. We are able to accept a wide range of lid designs. The majority of septic tank lids are circular, while some may be square depending on the manufacturer of your container.

We also provide several types of markers, such as stakes, imitation rocks, patio stones, and other similar items, to indicate the position of a septic tank.

Find the Right Size for Your Septic Tank

In order to lift the septic tank lid up to grade, risers are placed. It saves time and money by eliminating the need to search for and dig up septic tank lids. It also protects your irrigation system and landscape when pumping a septic tank. It is simple to construct a stairwell by yourself, or you may hire us to do it. Several alternative lid designs are available for us to work with. According to your tank manufacturer, the majority of septic tank lids are round, but some may be square. For the purpose of allowing grass to grow, a riser can be erected at grade or just below.

It is impossible to recover a riser that has been buried due to the difficulty in locating it.

Seal-R Products Tank Cover, Service Lid, Septic Tank Lid, Septic Cover, Seal-r Ring, Seal-r Lids, Safety Lids, Riser Pipe, Precast, Maintenance Pipe, Cast In Place Ring, Adaptor Rings

Seal-R™ LidsAvailable in 12”, 15”, 18” 24”, 30”, 36”.Seal-R™ RingsAvailable in 18”, 24”, 30”.Inner Safety LidsAvailable in 18”, 24”, 30”.

Easy 10 minute installation!Secure fit for all systems!Madesold by septic installers!Prevent ground water infiltration and save money at the same time!

Apply foam sealant to tank. Place ring over opening and apply foam.
Place plastic maintenance pipe on ring. Install lid.

Are you tired of using risers that are too tall or too short for the job you are completing?

Plastic riser pipe will give an exact height each time. Try our system and you will never have to carry concrete pipe and lids again. Save time by not having to assemble multiple sections. Now you can cast right into septic tank lids up to 6” thick with the 9” tallSeal-R™ Cast-In-Place Ring. The Cast-In-Place Ring will allow installers to use standard 24” I.D. tank riser material.

Easy Installation!No Heavy Lifting!Prevent ground water infiltration and save money at the same time!No expensive forms to replace!

Leave a Comment

Your email address will not be published. Required fields are marked *