Go to your basement or crawl space, and then look for the main sewer line that leads to your septic tank. Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside.
Are septic tank locations public record?
Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.
Can a metal detector find a septic tank?
If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.
How do I know if my house has a septic tank?
A surefire way to confirm whether or not your home has a septic system is to check your property records. It is likely that the building permit and blueprints for your home and property will contain information about the presence (or lack) of a septic tank.
How do you find a septic tank in an old house?
Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.
Can I drive over my leach field?
Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.
How much does a pump for a septic tank cost?
Average Cost To Pump A Septic Tank The national average cost to clean and pump a septic tank is between $295 and $610 with most people spending around $375. Depending on the size of your septic tank, pumping could cost as low as $250 for a 750-gallon tank, or as high as $895 for a 1,250-gallon tank.
Are septic tanks made of metal?
The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.
How long do septic tanks last?
A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.
Is septic tank better than sewer?
Although septic systems require a bit more maintenance and attention, they have a number of advantages over sewer lines. Since they don’t pump wastewater long distances to be processed at a water treatment facility, they use less energy overall and have a smaller environmental impact.
How far is septic tank from house?
Local codes and regulations that stipulate the distance of the septic tank from the house vary depending on the locale, but the typical minimum distance is 10 feet.
How do you tell if your septic tank is full?
How to tell your septic tank is full and needs emptying
- Pooling water.
- Slow drains.
- An overly healthy lawn.
- Sewer backup.
- Gurgling Pipes.
- Trouble Flushing.
How often should a septic tank be pumped?
Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.
How To Find My Septic Tank
- What is a septic tank
- How do I know if I have a septic tank
- And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
- What to Do Once You’ve Discovered Your Septic Tank
You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.
“How can I locate my septic tank?” is one of the most often requested inquiries we receive.
When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.
How to Locate Your Septic Tank
Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.
What Is a Septic Tank?
Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.
Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.
How Do I Know If I Have a Septic Tank?
What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.
- A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
- A septic system is likely to be installed in your home if you reside in a rather rural location.
- Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
- When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
- Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.
Why It’s Important to Know the Location of Your Septic Tank
You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:
1. To Be Able to Care for It Properly
The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.
2. If You Want to Landscape or Remodel Your Property
If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.
For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.
3. If a Problem With Your Tank Occurs
Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.
4. Ease of Getting It Fixed
Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away
1. Use a Septic Tank Map
First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.
- If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
- The county health department is responsible for keeping track of septic systems.
- A septic tank’s position could be depicted on a survey map, for example.
- The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.
2. Follow the Pipes to Find Your Septic Tank
Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.
- In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
- By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
- The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
- Going via the sewage line itself is another method of locating the septic tank utilizing it.
- Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
- When the snake comes to a complete halt, it has almost certainly reached the tank.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.
If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.
3. Inspect Your Yard
Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:
- Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
- Directly in front of the home Immediately adjacent to your well (if you have one)
- In close proximity to trees or densely planted regions
- In the shadow of a patio, deck, or other building
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.
Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.
4. Talk to Your Neighbors
If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.
5. Look for Your Septic Tank Lid
It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.
The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.
What to Do After You Find Your Septic Tank
Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.
However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.
1. Mark Its Location
The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.
2. Take Care of Your Septic Tank
Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.
In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.
For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.
Call a Professional Plumber
Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.
Request an Estimate for the Job
How to Locate Your Septic Tank
It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.
This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.
How To Find A Septic Tank: Step By Step
It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.
1. Gather Some Helpful Tools
Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.
Using this method, you may also locate the cover for your septic tank.
While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.
2. Use a Septic Tank Map
If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.
3. Start Ruling Areas Out
The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:
- Immediately adjacent to your well
- Beneath your home
- Directly against your home
- For example, underneath your driveway
- Under trees
- And other locations. Structures like a patio or deck are good examples of this.
4. Inspect Your Property
If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.
When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.
The likelihood of your septic tank being discovered in a few specific locations is quite high. Because of code issues or just because it doesn’t make sense, it’s highly unlikely that your septic tank will be located near any of the following locations:
- Your water well, if you have one (for a variety of reasons that are rather clear)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
- Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping
5. Inspect Your Yard
A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:
- If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
- Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.
The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.
6. Follow Your Sewer Main/Sewer Pipes
Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Once you’ve determined where these pipes exit your home, you can follow the pipe across your yard, using your metal soil probe every 2 feet or so, until you reach your septic tank. Additionally, every drain in your home leads to your sewer main, and your sewer main leads to your septic tank, which is located beneath your home.
If the line is not labeled, it is often made of metal and has a diameter of approximately four inches or so.
It is important to determine where this line exits your property and in which direction it is moving, as it often travels straight out to the septic tank itself.
7. Check Your Property Records
Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.
If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.
What to Do Once You Find Your Septic Tank
Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities.
You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!
Looking for Your Septic Tank? Here’s How to Find It
“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.
Why you need to know where your septic tank is located
If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.
In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.
How to find your septic tank
- Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
- Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.
After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.
- The post was published on July 16, 2019 under the category Septic Tank System.
How to find your Septic Tank at Home
When was the last time you paused to think about what happens to the things you flush down the toilet? It’s a little disgusting to think about, isn’t it? It’s possible that you’re conjuring up images of cobwebby crawlspaces with a swarm of creepy-crawly unmentionable creatures sliding, slithering, creeping, or crawling over crusty, rusted, ooey-gooey piping that’s oozing slimy goo from every joint. If this sounds like something you’re picturing then you’re not too far off the mark. I sincerely hope you are.
- That’s why I’d want to assist you in learning how to locate your septic tank.
- Simply dial 911 and ask for assistance in a calm manner.
- Most hide-and-seek games are won by septic tanks, which are well-known for their amazing ability to outperform the typical human rival.
- The good news is that.
- Contrary to common misconception, septic tanks are not often found in attics, basements, or any of the numerous closets that may exist in a house or apartment.
- Relax in your favorite place for a few minutes with your favorite beverage in hand.
- Yes, you read that correctly: your yard.
Alternatively, you can sink.
Or whatever it is that’s causing the terror to rise in your chest to rise in your chest.
Septic tanks are normally installed in one of your backyards or on your property.
How are you doing?
If your septic tank is in close proximity to your well, this should be avoided.
Septic tanks are often located on the other side of a house from where your home is located.
Tanks are often placed with their tops buried beneath the surface of the ground, usually at least 12 inches below the level of the ground’s surface.
A plastic access tube or a concrete riser structure that runs from the top of the tank to the ground level will often be included to give access for a Septic Pumping firm to empty the tank. Shankster Brothers (also known as Shanksters)
Many septic tank installers will attempt to blend these access risers into the surrounding landscaping so they don’t create an ugly eyesore.
So the next step is to mentally go about your yard, looking for any circular, plastic lids that could be lying around. These can range in size from 10 inches to 24 inches in diameter and can be either black or green. Second, if the answer is no, consider any round, square, or rectangular concrete lids that may be present in your yard or landscaping as a possible source of contamination. Often, they will be practically flat with the surface of the ground, allowing a lawnmower or rake to pass directly over the top of them without causing damage.
- Typically, the septic tank access will be no more than 10 feet away from your home, but in the event of an older home or a subsequent addition to the property, they may be closer than that.
- Hopefully, you have a basement to store your belongings.
- If your home does not have a basement or crawlspace, we will rely on other indications to locate your home.
- All of these pipes should converge into a single bigger pipe (usually 4 inches in diameter) that exits the house via one of the home’s walls.
- Now it’s time to go outdoors.
Check the area where the pipe comes out of the house. There may be a PVC pipe extending to the surface, with a threaded cleanout cap on it. If you find this, you’re well on the way to victory.
Take a check at the roof if your property is constructed on a slab with no basement or crawlspace beneath it. Check the roof for a vent pipe that is coming out of it. An internal vent that travels straight up, through the roof, and out the top of your home is common. If you can identify that vent, it might be possible to figure out where the pipe is departing the house. Continue walking outside from the house for a few steps, keeping an eye out for that round, square, or rectangular cover. If you can’t discover it, check for a little sunken place in the yard that could be hiding anything.
If you notice one of those, you might want to look underneath it to see if there is an entry point hidden there.
It’s possible that here is where your tank is lurking. If none of these suggestions have resulted in victory, and you begin to observe your neighbors peering through their blinds with those anxious glances that neighbors are so prone to giving.give us a call!
We have foundseptic tanksin many strange and unpredictable places. Here’s hoping you win the game on how to find your septic tank. Here tanky, tanky, tanky! If you need to schedule aseptic tank cleaning, pumping, or inspection, don’t hesitate to call Shankster Bros at(260)-982-7111. any time.
Septic systems on-site are used for accepting and treating wastewater in homes that are not linked to the municipal wastewater management system. A septic system is comprised of three components: a septic tank, a drain field, and piping. As a homeowner, it is your responsibility to properly operate and maintain your septic system in order to avoid system failure. For example, depending on the legislation in your area, you may be compelled to pump it on a regular basis. It is impossible to perform maintenance operations, however, if you do not know where the tank is located.
Steps to follow to locate your septic tank and drain field
The contractor that designed and constructed the septic tank on your property should have submitted an as-built diagram with the local health authority before starting work on the project. In the event that you have the contractor’s contact information, you can ask them for a schematic, which you can then use to pinpoint the location of your septic tank. If you do not have a copy of the schematic, you can request one from the local authorities. Depending on whether the installed system included electrical components, the schematic may be available at the regional building department offices.
- If you are unable to locate the tank using this diagram, you will need to do more research on the land in order to determine its position.
- This pipe is commonly found in the basement of a home, and it is a 4″ black pipe with a cleanout at the bottom.
- Simply look for possible access coverings or a structure that might be concealing it.
- These pumps are used to remove waste from the building.
- It is supposed to be connected to the sewage output pipe.
- As soon as you’ve discovered the sewer outlet in your basement, you may use it to figure out where the sewer line departs your home through an outside wall.
- As a result, it is probable that the tank will be positioned around the corner from the building.
Tips for locating your septic tank
Septic tank lids should be visible from the outside. An underground riser may have been added, which will make it simple to find your septic tank in some instances.
However, it is conceivable that the septic tank cover is buried underground, which is especially true for older homes. Following are some pointers to assist you in locating the septic tank in this and other similar situations.
- It may be possible to discover the septic tank lid underneath using a metal detector if it is buried. Prevent wearing footwear that contains steel or any other metal in order to avoid interfering with the readings of the detector
- Instead, you can use a flushable transmitter that is flushed down the toilet and then tracked with a receiver. When it comes to septic tanks, the strongest signal will be seen close to the intake region of the tank.
Depending on whether the septic tank is above or below ground, you may have to dig to get to it. Construction materials for septic tanks include concrete, fiberglass, or plastic, and their shapes can range from oblong to cylindrical to rectangular. The majority of modern septic tanks will have their lids positioned in the center of the tank, and the lid should be within three feet of the ground surface in most cases. However, depending on a variety of conditions, such as farming and other human activities on the property, it is conceivable that it will be significantly deeper.
Additionally, you may use a small steel rod to probe the earth in order to pinpoint exactly where the tank is located as you continue digging.
Inspecting the tank
It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been identified. First and foremost, you may unscrew the lid to inspect the scum and sludge layer beneath it. In addition, the use of tracer dye tablets allows you to check the septic tank without having to dig it up. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of two days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field has a glowing green hue surrounding it.
It is possible that someone will fall into the tank, causing significant damage or possibly death.
You can identify your septic tank without assistance from a professional, but it is a good idea to have someone who is properly educated in septic tank maintenance examine and maintain your septic tank on your behalf. The effluent filter in your tank should be washed into the open septic tank rather than on the ground in your yard if your tank has one. It may also be a good idea to make a note of the position of the septic tank when it has been discovered. This will be beneficial to anyone else who may require access to the septic tank in the future.
Septic tanks release combustible and hazardous gases, and as a result, they must be located in an open area.
3 Tricks to Locating Your Septic
Believe it or not, discovering your septic tank is not always straightforward—especially if you’re purchasing a property that hasn’t been well cared for in the past. Not to be concerned, though! Sherlock, put down your metal detector and follow these three easy steps to unravel the mystery behind your sewage system. Verify the status of the property records Assuming you’ve previously searched your land for any visible signs of a septic system (such as a huge mound, bald place in your grass, or a clearly visible tank lid), it’s time to start digging!
- The majority of town offices in New Hampshire keep records of all building permits, including those for the installation of septic tanks.
- Additionally, you may have gotten a septic system diagram as part of the home inspection process when you acquired your house or apartment building.
- Follow the Pipes to their destination.
- It is customary to construct the septic tank and drainfield parallel to the sewage pipe that runs from your home to the yard.
- The fact that the pipe is oriented in the direction of your yard serves as an excellent signal.
- This is the normal distance most septic tanks are positioned from most homes.
- Inquire of Your New Neighbors What happened to the last two recommendations that didn’t work out?
- Seriously, though, if you feel safe approaching them, they may genuinely be able to assist you in this situation.
- As a result, if your neighbor knows where their septic tank is, there is a good possibility that yours is in a location that is quite similar to theirs.
Please do not hesitate to contact us if you require assistance with your septic investigation and maintenance needs. Felix Septic Service is a company that provides septic service. 2020-08-20T16:51:27-04:00
How to Find My Septic Tank Lines
Credit: Petegar/E+/Getty Images for the image
In This Article
- Septic System Fundamentals
- Identifying and Locating a Septic Tank on Your Property
- Conducting Regular Inspections
- Checking for Clean-Outs
- Identifying Natural Indicators
- Viewing System Diagrams
- Seek Professional Assistance
- Check the distribution box
- Understand the size and scope of the project.
Are you curious about the location of your septic lines? It is critical to know where the septic tank is located on a property in order to properly manage and preserve the system. For example, you don’t want to pave over the ground or grow trees too close together in a forest. It is possible to obtain a copy of the septic tank diagram of the drain field, which will give you a fair sense of where the pipes will go. If this is not the case, you may need to attempt some other methods of locating septic drain lines.
The solids and liquids are separated within the tank by a baffle or wall that is built inside the tank.
When pipes get clogged or when drain fields become too saturated with fluids, problems arise.
Locating a Septic Tank on Your Property
Begin your search for the septic tank lines at the residence first. Drain lines from the home’s plumbing should be traced to the septic tank, which is typically located 10 to 20 feet from the home’s exterior. The drain line connects the tank’s end, which is located opposite the house, to the leach field. Check the natural slope of the ground to see whether the leach field may be found there. It is never a good idea to look for drain lines using heavy gear, wrecking bars, or jackhammers. Before excavating, contact your local electric utility provider or gas company to determine the location of underground gas or utility lines.
Plunge the long, thin metal probe into the earth until you can feel it strike the tank and feel the tank’s edges.
Perform Regular Inspection
According to industry experts, you should examine your septic tanks and, if required, pump them out once every three years. If you are experiencing gurgling sounds in your house or water backing up after your system has been repaired, a saturated drain field might be the source of the problem. Drain fields that have been clogged or damaged are unable to be rectified. In order for the septic system to function properly again, you’ll need to have a new drain field installed. Find capped clean-outs that are a few inches vertically above the ground in the leach field itself, or check behind a wall or in a closet in the basement for capped clean-outs.
- You can visually trace the orientation of the pipe from the clean-out if there is no other information available.
- Credit: Kyryl Gorlov/iStock/Getty Images for the image.
- When you are looking for the lines, look for grass or vegetation that greens in stripes when the grass surrounding it browns.
- Putting hot water into your system might cause snow or ice to melt above the drain pipes if the system is not properly insulated.
- If you have a deep system, as is the case for homes with basements, you will most likely not be able to observe natural signs since the drain field is too deep to be seen from above.
- Unless the system was built without a permit, the blueprints or designs for septic system installations are kept on file with the local health authority until the system is operational.
- If your search does not provide any relevant results, you can request a record search based on your street address or the tax account number associated with the property.
- If the agency has a copy of the record, they will mail it to you.
- If you don’t have a drawing of the septic system, you need enlist the assistance of a disposal system contractor or a certified liquid waste transporter to find it.
Another option is to purchase a flushable transmitter from a plumbing or rental business, or you may contract with a tank cleaning firm. The signal from the transmitter is picked up by a hand-held receiver after it has been flushed down the toilet.
Check the Distribution Box
There are certain septic tanks that feature an extra distribution box that is located a few feet from the tank on the tank’s downstream side. Water is channeled into the trenches by ports and pipes in the box. It is recommended that, if your system includes a distribution box, the box’s top be designed to expose the orientation of the ports that connect to the drain field lines. It is feasible to locate the box with a probe, but extreme caution should be exercised. Avoid applying excessive force to the probe, since this may result in damage to the box.
In most cases, individual drain lines run perpendicular to the intake line, but they may also branch into an H-pattern or other patterns that are appropriate for the terrain.
Find the location of your septic drain lines so that you can safeguard the area in and around them with a little detective work.
How to Find Your Septic Tank
Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.
5 Ways to Find Your Septic Tank
1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.
Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
When you do, that’s when your septic tank comes into play!
Look for the Lid.
You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
Those areas should be excavated in order to disclose the lids.
Get in touch with the pros.
Lifting concrete lids will necessitate the use of specialized equipment.
A fall into an unprotected septic tank has the potential to be lethal.
Produce your own diagram of your yard, which you may file away with your other important house paperwork.
That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!