How Much To Dig A Septic Tank? (Solved)

Septic System Cost Estimator

National Average $6,739
Typical Range $3,157 – $10,367
Low End – High End $450 – $20,000
  • The cost to build a septic tank system varies widely, depending on your location. According to SepticTankGuide.com, a standard or conventional gravity system for a 3-bedroom home on a level site with good soil would likely cost from $1,500 to upward of $4,000.

How deep should a septic tank be in the ground?

The general rule of thumb is that most septic tanks can be buried anywhere from four inches to four feet underground.

What is the cheapest septic system?

Conventional septic system These conventional septic systems are usually the most affordable, with an average cost of around $3,000.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Where are most septic tanks located?

Toe the Line. Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.

How big of a septic tank do I need?

The larger your home, the larger the septic tank you’re going to need. For instance, a house smaller than 1,500 square feet usually requires a 750 to 1,000-gallon tank. On the other hand, a bigger home of approximately 2,500 square feet will need a bigger tank, more than the 1,000-gallon range.

What are the alternatives to septic tanks?

Alternative Septic Systems

  • Raised Bed (Mound) Septic Tank Systems. A raised bed drain field (sometimes called a mound) is just like what it sounds.
  • Aerobic Treatment Systems (ATS) Aerobic systems are basically a small scale sewage treatment system.
  • Waterless Systems.

What is the most common cause of septic system failure?

Most septic systems fail because of inappropriate design or poor maintenance. Some soil-based systems (those with a drain field) are installed at sites with inadequate or inappropriate soils, excessive slopes, or high ground water tables.

What will ruin a septic system?

Substances like motor oil, paints, varnishes, and floor wax will damage organisms in your tank. This bacterium is necessary to keep your soil and groundwater free from pathogens. Instead of putting these oils down the drain, refer to your city’s waste management for recommended guidelines to dispose of these chemicals.

Is a septic tank always full of water?

A septic tank should always be “filled” to its normal liquid level, or the bottom of the outlet pipe which carries effluent to the absorption area. This normal liquid level is usually between 8” to 12” from the top of the tank on average (see picture at right).

How do I know if my house has a septic tank?

Some of the signs that your property has a septic tank are:

  1. The tank needing to be emptied each year.
  2. 2, 3 or 4 manholes in close proximity to each other above ground.
  3. Possible vent pipes above ground – these take unpleasant smells and gasses from the tank and distribute them into the air.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

How close can you build to a septic tank?

“Septic tanks should be sited at least 7m from any habitable parts of buildings, and preferably downslope.”

Learn how much it costs to Install a Septic Tank.

Septic tanks range in price from $3,157 to $10,367, or an average of $6,739 per tank. Installation of a conventional 1,000-gallon tank for a three-bedroom home might cost anywhere from $2,100 and $5,000. Materials range in price from $600 to $2,500, without labor. A comprehensive septic system, which includes a leach field (also known as a drain field), tank, and plumbing, can cost between $10,000 and $25,000 to install. A leach field installation might cost anywhere from $5,000 to $20,000, depending on the kind.

In the end, the cost of installing a septic tank is determined by the kind of system, the materials used, and the size of the tank.

This course will teach you about the several sorts of settings, such as conventional, drip irrigation, mound irrigation, evapotranspiration, recirculating sand, constructed wetland, and chambered irrigation.

Septic System Cost Estimator

Let’s run some numbers to see what the costs are. What part of the world are you in? What part of the world are you in?

National Average $6,739
Typical Range $3,157 – $10,367
Low End – High End $450 – $20,000

The cost information in this report is based on real project costs provided by 942 HomeAdvisor customers.

New Septic System Cost

Most tanks and systems cost between $2,000 and $10,000 to install a new typical anaerobic septic system. Aerobic systems range in price from $8,000 to $20,000. Depending on the size of your property, the composition of the soil, and the level of the water table, you may even have to pay an extra $10,000 or more for an alternative, specialized drain or leach field. Septic systems are composed of three major components:

  • Septic tank: Either anaerobic (requiring no oxygen) or aerobic (requiring oxygen but more complicated but more efficient)
  • Water runs to a leach field after it has been cleaned and separated in the septic tank, where it will naturally drain through sand, gravel, and soil in a cleaning process before reaching the water table
  • Water table: Plumbing: A drainpipe to the tank, followed by another branching pipe to your field will be required.

Optional components include the following:

  • Some types of systems use a dose or pump tank, which pumps wastewater up into mounded or elevated leach fields and recycles the water in some cases. Pump for aeration: If your aquarium is equipped with an aerobic system, you’ll want an aerator to force oxygen into the tank.
Find Local Septic Tank Installers

The installation of a traditional anaerobic system typically costs between $3,000 and $8,000 on average. Anaerobic systems are often less expensive to build than aerobic systems, which are more complicated. However, because they are less effective at cleaning the tank, you will need a bigger leach field to accommodate the increased burden. An anaerobic septic system is a very basic system that consists of a pipe that runs from the home to the tank and a branching pipe that runs from the tank to the drain field, among other components.

Aerobic Septic System Cost

Aerobic systems, which are those that require oxygen to work properly, cost on average between $10,000 and $20,000 per system. If you’re moving from anaerobic to aerobic fermentation, you’ll almost certainly need a second tank, but the conversion will only cost you $5,000 to $10,000. Aerobic systems break down waste more effectively in the tank than anaerobic systems, allowing you to use a smaller drain field in many cases – which is ideal for houses with limited space. An aerobic wastewater system is a wastewater system that depends on aerobic bacteria (bacteria that thrive in the presence of oxygen) to break down trash in the tank.

You’ll need an aerator as well as an electrical circuit that connects to the system to complete the setup. Small, mounded, or speciality fields may necessitate the addition of a dose or pump tank to assist in pushing effluent (sewage or wastewater) upward or out in batches.

Get Quotes From Local Septic Tank Pros

Beyond the tank and leach field, there will be a few more costs to consider when creating your budget for the project. You may already have some of these costs included in your total project pricing, so make sure to get line-item prices on your estimate.

  • Excavation costs $1,200–$4,500
  • Building permits cost $400–$2,000
  • And a perc test costs $700–$1,300. Labor costs range from $1,500 to $4,000
  • The cost of septic tank material ranges between $500 and $2,000.
  • Plastic and polymer materials cost $500–$2,500
  • Concrete costs $700–$2,000
  • And fiberglass costs $1,200–$2,000.
  • 500: $500–$900
  • 750: $700–$1,200
  • 1,000: $900–$1,500
  • 1,200: $1,200–$1,600
  • 1,500: $1,500–$2,500
  • 2,000: $3,000–$4,000
  • 3,000: $4,500–$6,000
  • 5,000+: $7,500–$14,000
  • 500: $500–$900
  • 1,200: $1,200–$1,

Leach Field Cost

Installing a leach or drain field, which is a component of your septic system, can cost anywhere from $3,000 to $15,000 in total. The cost of a typical drain field ranges from $2,000 to $10,000. The drain field, also known as the leach field, is the component of the septic system that is responsible for returning wastewater to the soil. Most of the time, a flooded area in the yard or a strong stink of sewage on the property is the first symptom of a problem with the drainfield. It is possible that you may require further treatment for blocked or flooded fields, which would increase the cost of the drain field repair from $10,000 to $50,000.

Alternative Septic Systems Cost

When you have a tiny property, a high water table, high bedrock, poor soil, or just wish to utilize less space, an alternate septic system is a good choice.

Mound Septic System Cost

Installing a mound septic system can cost between $10,000 and $20,000 dollars. In places with high water tables, thin soil depths, or shallow bedrock, this is the most costly system to build; yet, it is frequently required. In order to create a drain field, it uses a raised mound of sand rather than digging into the soil. Its extra cost is a result of both the additional technology required to pump sewage upward into the mound and the materials and labor required to construct the mound in the first place.

Recirculating Sand Filter Septic System Cost

Sand filter septic systems range in price from $7,500 to $18,500. They can be built above or below ground depending on the situation. In order to disperse the wastewater in the ground, they employ a pump chamber to force the wastewater through a sand filter. The liner of the filter box is normally made of PVC. This is accomplished by pumping the effluent through the sand and returning it to the pump tank, where it is then disseminated throughout the ground.

Drip Septic System Cost

Drip systems range in price from $8,000 to $18,000, depending on the size and complexity. They operate in the same way as previous systems, with the exception that they employ extensive drip tubing and a dosage mechanism. They deliver lower dosages over a shorter period of time, which is particularly effective at shallow soil depths. This method is more expensive than a standard system since it requires a dosage tank, a pump, and electrical power to operate.

Evapotranspiration System

Evapotranspiration systems range in price from $10,000 to $15,000 per system. In order to allow the liquid to evaporate from the top of an open-air tank, they employ a novel drain field configuration. They’re only usable in dry, arid areas with little rain or snow, thus they’re not recommended.

Built Wetland System

Built-in wetland systems range in price from $8,000 to $15,000, with the cost increasing if an aerobic tank is included. They are designed to simulate the natural cleaning process observed in wetland ecosystems.

After traveling through a wetland tank, where it is treated by microorganisms, plants, and bacteria, it is returned to the soil. The waste also has the effect of assisting the growth of wetland plants and the population of microbes.

Chambered System

Installation of chambered systems ranges from $5,000 to $12,000 dollars. They employ plastic perforated chambers surrounding pipes, which are frequently laid in sand, to keep them cool. Gravel is no longer required as a result of this. They are quick and simple to install, but they are more subject to crushing pressures, such as those caused by automobiles.

Septic Tank Replacement Cost

The cost of replacing a septic tank ranges from $3,000 to $10,000. From 30 to 40 years, you may anticipate your system to serve you well. The system may crack or corrode as a result of the failure and the resulting contamination of groundwater with toxic waste is an issue. When this occurs, the well water may get polluted, the yard may become marshy, and the septic system may become inoperable or fail completely. Here’s a breakdown of the various components of a septic tank, along with an estimate of their usual costs: Replacement of a septic tank pump costs between $800 and $1,400.

Replacement of the filter costs between $230 and $280.

Drain Field Replacement Cost: $7,500.

Septic System Maintenance Costs

It is essential that you pump and clean your septic tank at least once a year. In addition, you should get it examined at least once every three years. The proper maintenance of your septic tank will save you money in the long term, and it will also help you avoid potentially hazardous situations. The Environmental Protection Agency (EPA) suggests the following steps to keep your septic system in good working order:

Inspect and Pump Your Septic Frequently

Typically, the cost of septic tank pumping runs from $300 to $550, or around $0.30 per gallon – most septic tanks have capacities between 600 and 2,000 gallons. Every three to five years, you should have your septic tank inspected and pumped by a professional. If you have a bigger home (with more than three bedrooms) and you tend to use a lot of water, you should try to get it pumped at least once every three years. An checkup of a septic system might cost anything from $100 to $900. Your septic inspector will do a visual inspection of the system.

  • Initial inspection costs between $250 and $500
  • Annual inspection costs between $100 and $150
  • And camera inspection costs between $250 and $900.

Use Household Water Efficiently

A toilet that leaks or runs continuously might waste as much as 200 gallons of water per day, although the average family consumes just 70 gallons of water. Take, for example, high-efficiency toilets, which consume 1.6 gallons or less of water every flush or less. The use of new, high-efficiency washing machines and showerheads can also help to reduce water waste, which will relieve the load on your septic system.

Properly Dispose of Your Waste

Your septic system is responsible for disposing of everything that goes down your drains and toilets.

One easy rule of thumb is to never flush anything down the toilet other than human waste and toilet paper, unless it is absolutely necessary. That implies you should never flush the following items down the toilet or drop them down the sink drain:

  • Cooking grease or oil, baby wipes or wet wipes, dental floss, diapers, feminine hygiene products, cigarettes, cat litter, and paper towels are all examples of items that fall into this category.

Maintain Your Drainfield

The drainfield of your septic system is a component of the system that eliminates waste from the septic’s liquid. You should take steps to keep it in good condition, such as:

  • Never park or drive your vehicle on your drainfield. Don’t ever put trees near your drainage system. Maintaining a safe distance between your drainfield and roof drains, sump pumps, and other drainage equipment
Get in Touch With Septic Tank Installers Near You

A septic tank or septic pump tank can range in price from $350 to $14,000, depending on the material used and the size of the tank. In most home situations, you won’t have to spend more than $3,000 on the tank’s actual construction. The majority of big, high-priced units are intended for use in apartment buildings or as part of a communal sewage system.

See also:  How Much Does It Cost To Fill In A Septic Tank? (Solution)

Concrete Septic Tank Cost

Concrete tanks range in price from $700 to $2,000. The total cost of installation ranges from $2,300 to $6,500. They’re one of the most often seen forms of installation. Despite the fact that they are vulnerable to cracking and separation, they are often resilient for several decades. It’s critical to have it carefully inspected on a regular basis for cracks and runoff, among other things. Inspections and frequent cleanings will assist to extend its useful life. Your professional can tell you how frequently you should get it inspected, but it’s normally every one to three years.

Plastic and Poly Septic Tank Prices

Septic tanks made of plastic range in price from $500 to $2,500 on average, not counting installation costs. Plastic is a long-lasting, lightweight, and reasonably priced building material. They do not break as easily as concrete and do not rust. Because of their small weight, plastics are more susceptible to harm during the installation process.

Fiberglass Septic Tank Prices

Fiberglass septic tanks are typically priced between $1,200 and $2,000, not including installation. Fiberglass does not split or rust readily, but it is prone to damage during the installation process, much like plastic. However, because of its lighter weight, it is more prone to structural damage, and the tanks themselves can move in the soil.

Steel

It’s unlikely that you’ll ever see a new steel tank constructed. They will rust or corrode with time, no matter how well-made they are at the time. As a result, they are not permitted by many municipal construction rules, and you will only encounter them in existing installations. Steel is not a long-lasting material in the earth, and it is the least preferred.

Labor Costs to Install a Septic System

The cost of labor accounts for 50 percent to 70 percent of your overall expenses. Labor is typically more expensive than the tank itself in a normal installation, making it the most expensive option. For example, while the size required for a 3 to 4-bedroom home may cost between $600 and $1,100, the labor to install it might cost anywhere between $1,500 and $4,000.

Compare Quotes From Local Pros

Here is a breakdown of how much septic tanks cost in different parts of the country. Massachusetts:$9,700 California:$4,500 Florida:$5,300 Texas:$8,000 $5,600 in New York City Colorado:$7,800 Idaho:$10,000

DIY vs. Hire a Septic System Pro

The installation of a septic system is a time-consuming operation. An incorrectly fitted unit can result in water contamination, structural damage to the property, and the need for costly repairs.

In addition, an unpermitted installation might make it harder to sell and insure a property when it is completed. Make a point of interviewing at least three pros before making a final decision. Contact a septic tank installation in your area now for a free quote on your job.

FAQs

A septic tank has an average lifespan of 20 to 30 years, however it may live anywhere from 14 to 40 years, depending on the following factors:

  • What it is made of is a mystery. Concrete tends to require more care, but commercial-grade fiberglass and plastic are known to survive for decades in most environments. It’s amazing how well you’ve kept it up. Every one to three years, have your system inspected and pumped out
  • Every three to five years, have it pumped out. It will depend on whether or not it gets vehicle traffic over the leach field. Driving over the leach field compresses it, which increases the likelihood of it failing. The soil’s chemical makeup is important. The length of time it may endure varies depending on the soil type and depth.

What are the signs I need a new septic tank?

There are a few indicators that it is time to replace your septic tank. These are some examples: If you smell sewage, you may have a solid waste problem in your septic tank that has to be dealt with immediately. Standing water: If there is no clear explanation for standing water, such as a significant rainstorm, it is possible that you have an oversaturated drain field, a damaged pipe, or a faulty septic system. A clogged septic tank will cause pipes to drain more slowly than they would otherwise be.

Construction on your home or the addition of more occupants will have an impact on your septic system.

pollution of nearby water: A septic tank leak can result in wastewater contamination, which can deposit nitrate, nitrite, or coliform bacteria in water sources around your property as a result of the leak.

Old age: If your septic system has reached the end of its useful life, it is time to replace it.

Does homeowners insurance cover septic systems?

Many unforeseen and abrupt repairs to septic tanks are covered by homeowners’ insurance policies. They do not, however, often cover harm caused by a failure to perform routine maintenance. Make certain that you are pumping and cleaning it on a yearly basis.

How much do septic system repairs cost?

Repairing a septic system can cost anything from $600 to $3,000. Most tank repairs and replacement parts cost less than $1500 for each type of repair or replacement part mentioned below. Leach fields range in price from $2,000 to $20,000.

  • Tank Pumps cost between $800 and $1,500. A septic tank that is placed below the drain field may necessitate the installation of a pump to transport wastewater to the drain field. Pumping costs between $300 and $600 per year. Pumping is required to remove solid waste from even a perfectly functioning system every two or three years, even if it is in good working order. Tank Lids cost between $100 and $300 to purchase and install. If you purchase the lid and attach it yourself, it will cost you between $50 and $150
  • Tank Lid Risers range in price from $300 to $1,000. Deeply submerged tanks can have their lids raised to the surface by using these devices.
Still Have Questions About Septic Tanks?

A Quick Look at Septic Tank Prices

  • Total cost: $3,900 on average
  • $1,500 to $5,000 on a sliding scale
  • Anaerobic septic tanks cost between $2,000 and $5,000
  • Aerobic septic tanks cost between $10,000 and $20,000
  • Gravity septic tanks cost between $1,500 and $4,000
  • Mound septic tanks cost between $10,000 and $20,000
  • Chamber septic tanks cost between $1,500 and $5,000
  • Conventional septic tanks cost between $2,000 and $5,000.

The wastewater generated by your household is teeming with potentially harmful germs. In order to properly dispose of waste and prevent it from backing up into your sinks and toilets, you must ensure that your septic tank is in good working condition. This Might Also Be of Interest to You: What Is the Difference Between a Septic System and a Sewer System? Everything you need to know about septic tank replacement, including how much it will cost, can be found in this article.

What Is a Septic Tank?

A septic tank is an underground chamber that is used to treat residential wastewater to a modest degree. It is intended to store wastewater for an extended period of time, allowing particles to settle to the bottom and oil and grease to float to the surface. After that, the liquid waste is filtered away.

How Much Does It Cost to Install a Septic Tank?

In most cases, a new septic tank system will cost you around $3,900 to install. It costs between $1,500 and $5,000 to install a conventional 1,250-gallon tank, which is the perfect size for a three- or four-bedroom house.

This price includes the tank itself, which ranges in price from $600 to $2,100 or more depending on the size and kind. Workman’s compensation is included in the price of the installation and often ranges from $1,500 to $4,000.

Types of Septic Tank Systems

Septic tank installation and replacement costs are heavily influenced by the type of system that you select to use. Tanks come in a variety of shapes and sizes. Here are a few examples:

Anaerobic Septic System

Anaerobic systems are a popular alternative for many homes since they don’t require any additional electricity or chemicals to function properly. Anaerobic systems include microorganisms that do not require oxygen to exist and hence are called anaerobic systems. Solid waste is broken down by microbes, and any leftover liquid waste is pumped out and spread beneath the surface of the soil. The garbage is naturally recycled when the water seeps into the ground and returns to the environment. The installation of these devices is between $2,000 and $5,000.

Aerobic Septic System

Aerobic systems, in contrast to anaerobic systems, make use of microorganisms that do not require oxygen to live. To activate the bacteria in the tank, oxygen is injected into it, and the bacteria then feed on the solid waste. Aerobic systems perform effectively in soils that are unsuitable for other systems and in areas where the groundwater table is elevated. It is an excellent choice for residences that are close to a body of water. Aerobic systems are more costly to install than anaerobic ones.

Gravity Septic System

Gravity septic systems employ gravity to filter and move water through the system. They must be put on a mild slope in order to allow water to flow without the use of a pump. The cost of installation ranges from $1,500 to $4,000.

Conventional Septic System

A standard septic system is comprised of a septic tank and a trench that serves as a drain field for the collection of waste. The trench is built on stone or gravel and is designed to allow water to move through it easily. In order to prevent sand or dirt from contaminating the clean soil, geofabric is laid over the top of the trench and secured in place. In order to function properly, a traditional septic system requires a huge amount of room. The installation of these devices is between $2,000 and $5,000.

Mound Septic System

If your groundwater table is close to the surface, a mound septic system is the most appropriate option for your situation. An area for the septic system is prepared, and a sand mound is built to allow effluent from the tank to be pumped into the mound in modest amounts. The sand then acts as a filter, preventing the water from reaching the soil and groundwater. This design necessitates a large amount of floor space. They’re also expensive to install since a sand mound needs to be built before they can be utilized.

Chamber Septic System

Chamber septic systems have lately gained popularity as an alternative to traditional septic systems.

They are comparable to conventional systems, with the exception that plastic chambers, rather than gravel, are utilized in the drain field. These are less difficult to build and have a lower carbon footprint. The cost of installing them ranges from $1,500 to $5,000.

Septic Tank Materials

Another aspect that influences cost is the type of material used to construct your septic tank. The following are some of the most often seen materials:

Concrete

Concrete septic tanks are the most prevalent form of septic tank because they are extremely long-lasting and reliable. They can survive for 20 to 30 years if they are properly maintained. Concrete, on the other hand, may break with time. When concrete is reinforced with rebar, the strength of the concrete is increased when subjected to pressure. Because of its weight, installation is more difficult and necessitates the use of specialized equipment. The cost of a typical-sized concrete tank ranges from $720 to $2,050 dollars.

Fiberglass

Fiberglass does not deteriorate when utilized underground, and because it is nonporous, it will not support the formation of algae. Because of the tank’s modest weight, it is easy to install. You won’t have to worry about cracking since, unlike concrete, it will not expand or shrink as the weather changes. The typical cost of a fiberglass tank is between $1,600 and $2,000.

Plastic

Tanks made of plastic are lightweight and simple to install. They’re also fairly long-lasting. Plastic tanks range in price from $830 to $1,400 on average, depending on the kind.

Steel

In spite of steel’s strength and durability, septic tanks built of steel are susceptible to rust and collapse if not properly maintained. As a result, several municipal governments have tightened their restrictions in order to discourage their usage. Typically, you’ll discover them in regions where the system was already in operation. If you are able to have one installed, they range in price from $900 to $9,900.

What Size Septic Tank Do You Need?

The size of your septic tank is normally decided by the number of bedrooms in your house. This is used to calculate the amount of water that will flow through the system on a daily basis. In general, the expense of a system increases in direct proportion to its size.

Two Bedrooms

A septic system with a minimum of a 750-gallon septic tank is required for a two-bedroom residence. However, in many localities, a 1,000-gallon tank is the least capacity that may be accommodated.

Three Bedrooms

A minimum of a 1,000-gallon water tank is required for a three-bedroom residence, which handles around 360 gallons of water each day on a daily basis.

Four Bedrooms

A bigger tank, with a minimum volume of 1,250 gallons, is required for a four-bedroom residence. It is capable of handling around 480 to 600 gallons of water each day. Additional Related Articles:

  • How to keep the cost of septic tank pumping to a bare minimum
  • 3 Symptoms of Sewer and Septic System Problems
  • Do you have a clogged sewer line? Here’s What You Should Do
  • Water Sewer Line Repair: Do It Yourself or Hire a Professional
  • Listed here are 15 common plumbing problems that every homeowner should be aware of.

Septic Tank Repair Costs

It’s conceivable that only a certain component of your septic tank has to be replaced rather than the complete tank. Repairs and replacement parts can be purchased for a fraction of the cost of a complete system replacement. The following are some of the most often seen repairs:

Drain Field

Drain fields can get overloaded and flood, resulting in sewage backing up into toilets and sinks. The cost of replacing a drain or leach field ranges from $3,500 to $11,000.

Tank Pump

A replacement septic tank pump typically costs between $500 and $1,200.

Tank Filter

It is the most typical type of filter change that is performed by homeowners. It typically costs between $230 and $280.

Tank Lid

Concrete coverings and steel lids may break and corrode as a result of exposure to the elements. In most cases, you can repair a septic tank lid on your own for about $35 and $60. In most cases, having it changed by a professional is more expensive.

Tank Baffle

The baffle is responsible for directing wastewater through the septic tank. A replacement baffle piece will cost between $23 and $44 dollars.

Additional Factors to Consider

A septic tank can be built either below or above ground, depending on your preferences. Because of the amount of excavating and footing preparation required, installing a tank underground is a pricey endeavor. Underground septic tanks necessitate the construction of a drain field that can accommodate a soakaway. In addition, because the soakaway allows for part of the wastewater to drain into the ground, the tank will require less emptying over time. Over time, this might result in a reduction in your expenditure.

Some demand that an inspector check and approve the site, which might result in a fee being charged to the homeowner.

See also:  How Much Is A 500 Gallon Septic Tank?

How Long Does a Septic Tank Last?

The lifespan of a septic tank varies based on the material used and the type of system used. The lifespan of a septic tank might be reduced if the tank becomes clogged due to roots or floods from groundwater. Septic systems have a lifespan of 15 to 20 years on average. Maintaining your septic tank on a regular basis is the most effective approach to extend its life. Keep in mind that maintaining your tank entails more than just draining out the contents; it’s also crucial to have a professional evaluate your tank on a regular basis and perform routine maintenance.

In the event that you have a plan in place, you can call our 24-hour repair hotline anytime a covered problem develops.

How Much Does a New Septic Tank System Cost?

The average cost of a new septic tank system is between $3,060 and $9,810 dollars. While high-end systems can cost up to $20,000, entry-level systems can be purchased for as little as $465. Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. Simply simply, trash is an unavoidable component of everyday existence. Septic tanks perform the dirty work for you, and they’re not particularly attractive. Anaerobic septic systems, which are the most common type, cost between $2,000 and $10,000.

Everything from the size of your property to its soil type and water table depth will determine which option is ideal for you.

How Much Does a New Septic Tank System Cost Near You?

In general, the cost of a new septic tank system is $6,420 on the national level, while particular costs vary from state to state depending on a variety of criteria. As a starting point, each state has its own set of fees and regulations for obtaining construction permits and licenses. Before starting a septic tank project, be sure you understand the requirements in your region. The cost of a septic system varies from area to region as a result of variations in soil composition across the country.

Septic tank system prices are around $3,000 in areas with sandy soil due to the lower labor and material expenses associated with well-drained soils in these locations.

As a result, expenses in New York, Washington, and Pennsylvania tend to be greater than in other states. Outside of these locations, residents may anticipate septic system expenses to be in line with the national average.

Septic Tank System Cost Breakdown

The entire cost of installing a septic system will ultimately be determined by three factors: the materials and labor necessary to complete the installation, as well as the cost of digging a leach field on your land.

Materials

Concrete, fiberglass, and plastic are some of the most often used materials in septic tank systems. Concrete tanks are the most commonly used because of their longevity; with regular care, they may survive for up to 30 years or more. Concrete septic tanks typically cost between $700 and $2,000 on average. Plastic septic tanks are generally affordable, ranging in price from $500 to $2,500 per tank. On the other side, fiberglass tanks are more costly, ranging from $1,200 to $2,000 per tank.

Labor

It is possible that labor prices may vary by location and will be dependent on the size and materials used in the new septic tank system. However, in most cases, labor costs account for 50 percent to 70 percent of the overall cost of a septic tank system installation. Even though installation is more expensive than purchasing the tank alone, it is well worth it if you do not have the time or resources to undertake yet another home improvement project at this point in your life. Make certain that you and your contractor or plumber go over all of the specifics.

Additionally, construction permits, which normally cost between $400 and $2,000, and perc tests, which cost between $700 and $1,300 on average, are additional expenses that may or may not be included in your septic tank installation prices.

Leach Field

Leach fields, which are a type of trench, are used in conjunction with septic tank systems to collect and treat wastewater. It is the component of your septic system that returns the wastewater to the earth, often known as a leach field or drain field. Leach fields range in price from $2,000 to $10,000. Photo courtesy of Natalia / Adobe Stock

How Much Does a New Septic Tank System Cost by Type?

Each form of septic system has its own set of advantages and disadvantages. Even though anaerobic systems need less maintenance, they are not suitable for use on smaller parcels of land. Anaerobic systems, on the other hand, may function effectively in compact places but need additional effort.

Anaerobic

Septic tanks can be classified as either anaerobic (requiring no oxygen) or aerobic (requiring oxygen). Anaerobic systems, which are more frequent, cost between $3,000 and $8,000 on average, according to the manufacturer. They are often less expensive to install than aerobic systems, but they are less efficient and need a bigger leach field than aerobic systems. In an anaerobic septic system, a pipe connects the home to the septic tank, and another pipe connects the septic tank to the leach field, where the waste is disposed.

Prior to the wastewater being distributed into the soil, anaerobic bacteria break down solid waste in the wastewater treatment system. This type of system does not require any additional electricity or chemicals, which makes it a popular choice among homeowners.

Aerobic

Aerobic septic systems make use of oxygen that is fed into the tank to activate bacteria that feed on the solid waste in the tank. These systems are more expensive than anaerobic systems, costing between $10,000 and $20,000, but they are more efficient and may be used effectively on smaller sites. In contrast to anaerobic systems, they require more electricity to function well. Connecting it to a backup power generator will guarantee that everything continues to function correctly in the event of a power loss.

How Much Does a New Septic Tank Cost by Style?

The size and location of your property will play a role in determining which type of septic tank system is best for your needs. The mound or sand filter aerobic septic tank systems are recommended for smaller properties, while those with greater room have a wider range of alternatives.

Mound

Expect to spend more money if you choose a mound septic system, which may cost between $10,000 and $20,000 to install. A sand mound is constructed on top of the septic system region to collect wastewater that has been pumped out of the tank. Water is filtered via the sand before it enters the soil and groundwater. Even though these systems are costly, they are important in locations where the water table is high.

Sand Filter

Sand filter septic systems employ a pump to force wastewater through a sand filter at a low pressure before it is released into the soil or groundwater, effectively treating and removing nutrients from the wastewater. Despite the fact that nutrients such as phosphorus and nitrogen are naturally found in trash, when they collect in surface water, they can degrade water quality and cause aquatic ecosystem harm. They range in price from $7,000 to $18,000 and may be constructed either above or below ground.

These systems are most effective in locations with high water tables or in areas where there are bodies of water nearby.

Chamber

Chamber septic systems are identical to conventional systems, except that they employ plastic chambers in the leach field instead of gravel to collect the waste. They range in price from $5,000 to $12,000 to install. Chamber septic systems are excellent solutions for sites with varying input quantities, such as vacation homes or rental properties. You should avoid placing it near your driveway or parking area if you choose this type since driving over it might cause considerable (and stinky) harm.

Drip

Drainage systems that employ drip tubing and a dosing device to release smaller, scheduled dosages of waste on a regular basis are called drip septic systems.

They are particularly effective in soils with a short depth. It takes more components to install a drip system than it does to install a traditional system, such as a dosing tank or a pump, and it may cost anywhere from $8,000 to $18,000, depending on the size of the system.

Evapotranspiration

Evapotranspiration septic systems range in price from $10,000 to $15,000 and are particularly beneficial in dry regions and locations with thin soil. They have special leach fields that allow wastewater to evaporate from the top of an open-air tank, which is not common in other tanks. If you reside in an area where there is a potential of snow or rain, an evapotranspiration septic system should be avoided at all costs. The dampness might eventually cause them to collapse, and the repair process for a septic tank is not particularly attractive.

Built Wetland

As you may have guessed, constructed wetland septic systems are designed to replicate the natural water treatment process found in wetlands. Water is treated in a wetland tank by microbes, plants, and bacteria before being released back into the environment. As a result, the waste promotes the growth of plants and bacteria. The cost of these environmentally friendly systems ranges from $5,000 to $12,000.

What Factors Influence the Cost of a New Septic Tank System?

Several factors influence the cost of a septic tank installation project. In general, costs rise as the size of the organization grows. If landscaping and permits are necessary for the installation of your septic tank, you should budget an extra $600 at the very least. The sort of material you choose will also have an impact on the price, with plastic being very inexpensive when compared to concrete. Furthermore, if you choose a more customized design over a stock model, you will be responsible for the additional work costs.

As a result, the amount you pay will be determined by the location of your home as well as the soil type that surrounds your property.

FAQs About Septic Tank Systems

A septic system that has been poorly built can cause serious difficulties, such as water contamination and structural damage to your property. Repairs to a septic system are not inexpensive. Because of the high level of danger involved in constructing septic tanks, this process should be left to the professionals. Call around and talk about your requirements (as well as your budget) with a number of septic tank businesses in your region to find the ideal match.

What should I consider when installing a septic tank system?

A septic tank is an essential component of every property. Damage to your property as a result of structural failure or leaks may be costly, as well as dangerous to human and environmental health. It’s possible that the unpleasantness will even compel you to check into a motel for the night. Prior to establishing your septic tank system, take the following factors into consideration:

  • Soil type
  • Landscaping
  • Structural hazards (avoid places near cars or heavy machinery)
  • The size of the property
  • The size of the septic tank
  • Future maintenance
  • And the location of the tank

What other projects should I do at the same time?

Excavation is frequently required when installing a septic tank system (unless you opt for an above-ground tank). Once the excavators have broken ground, you may proceed with further subterranean projects that will save you time and money in the long run, such as:

  • Establish underground utilities and construct a retaining wall before beginning work on the sprinkler system.

Septic Tank Installation and Replacement Cost

The typical cost in the United States ranges from $500 to $5,000.

The national average cost of a septic tank installation or the cost of replacing an outdated septic system is dependent on a number of different variables.

Septic Tank Installation Average Costs
National Minimum Cost $500
National Maximum Cost $5000
National Average Cost $1500

According to the Environmental Protection Agency, one in every five residences in the United States relies on a septic system for wastewater management (EPA). In the case of septic systems, you may have a septic system for your home alone, or you may be connected to a communal system that services a small number of homes. Untreated wastewater created by a house or company is treated on site by a septic system, which is an on-site treatment system. Sewage lines convey wastewater from your shower, toilet, sinks, clothes washer, and trash disposal away from your home and into a septic tank buried in your yard.

  1. Solids are separated from floatable debris in the septic tank, and the leftover liquid drains from the tank through a series of perforated tubes and onto a drain field or leach field after being separated in the tank.
  2. The usage of septic systems is popular in rural regions that do not have access to a centralized municipal sewer system.
  3. Tank capacity ranges from less than 1,000 gallons to more than 2,000 gallons, with the size of the tank determined by the quantity of water you consume on a daily basis.
  4. Condos, apartments, residences, business spaces, and other types of structures might benefit from septic system installation or replacement services.

What’s in this cost guide?

  • Soil type
  • Tank size and kind
  • Equipment
  • Installation
  • Maintenance
  • Lift station
  • And more. Septic systems that are not conventional
  • How septic tanks function
  • Signs that you need to upgrade your system
  • How to employ a professional

Alternative septic systems

Alternative techniques are particularly effective on steep locations, highly rocky land, or poor soil. Among the options available are aerobic septic systems, mound septic systems, raised-bed septic systems, and others. The cost of a septic system installation or replacement may be greater or cheaper than the average depending on the area and kind of system. Locate the most qualified septic system consultant for your project needs. Zip code must be entered correctly.

Signs you need a new system

Anyone would not want sewage water rising up through their front yard on one of the hottest days of the summer season (or even on the coldest day of winter). Waterborne pathogens such as protozoa, bacteria (such as E. coli), and viruses may be spread through fecal matter, making wastewater not just stinking and disgusting, but also potentially deadly. It is possible for unclean wastewater to drain through the soil and pollute the water you and your friends and neighbors drink if your septic system is leaky, overwhelmed, or otherwise compromised.

Knowing what indicators to look for might help you catch an issue before it becomes a major problem.

This includes having your septic tank pumped out by a professional every three to five years.

Other indicators may indicate that it is necessary to contact a septic system specialist as soon as possible to either repair or replace the system.

How Much Does a Septic System Cost: Replacement and New

If your septic system is in need of replacement, call us today. Is it important for you to know how much it will cost to rebuild your septic system? In the event that you’re thinking of purchasing a home that will require a new septic tank system or obtaining a construction loan to develop a new property, you may be interested in knowing the average cost of a septic system. It is quite expensive to purchase such a system because it takes a substantial amount of labor from your contractor. A variety of factors influence the cost of a conventional septic system.

See also:  When Should I Pump My Septic Tank? (Perfect answer)

What is a Septic System, and How Does it Work?

A septic system is an underground wastewater treatment facility that is most commonly employed where there is no access to a municipal sewage system. Instead of urban regions, they are more typically seen in rural locations. A basic septic system is comprised of three components: a septic tank, a distribution box, and a leach field (or leach field). A leach field is also referred to as a drain field or a soil absorption field in some circles. A septic tank aids in the digestion of organic matter and the separation of floatable stuff such as fats, oils, and solids from wastewater in the treatment process.

The first septic tanks were put in place in the late 1800s, but it was not until the 1960s that they began to gain widespread acceptance.

How Much Does a Septic Tank Cost?

The cost of a septic tank is determined by a variety of factors. The number of bedrooms in your home is the single most important element in determining how much you will have to pay for a septic tank installation. More bedrooms imply a greater number of potential tenants, as well as a greater capacity septic tank required. The size of a septic tank for a three-bedroom house is typically 1000 gallons in capacity. The price of a 1000-gallon septic tank ranges from around $600 to $1200. Please keep in mind that the cost of a product might vary greatly depending on where you are located on a price spectrum.

A bigger septic tank will cost you between $1200 and $2000, depending on its size.

When it comes to septic systems, however, this is not where the most expensive parts of the system are located.

When considering the installation of a new septic system or the replacement of an existing one, consider how much money will be spent on the leaching area.

The location of your property, the quality of the soil, and the presence or absence of a water table are all factors that might influence the cost of your septic system installation.

The Cost of Septic System Installation

Understanding how much it will cost to replace a septic system is significantly more important than understanding how much it will cost to replace a tank. When compared to the expense of repairing a leach field, the cost of replacing a septic tank is comparatively affordable. The cost of replacing a leach field might range from $5000 to $50,000 or even more!. That is right; you read that correctly. The cost of a septic system replacement can vary greatly depending on a number of factors, including the soil’s health, the level of the water table, the presence of designated wetlands nearby, and the location of your property.

  1. The engineer will begin by doing a land survey to assess the costs of the system replacement.
  2. They will create what is known as a “as-built” model, which depicts how the system is put together.
  3. They make use of the information gathered from these tests in order to build a septic system that will work effectively.
  4. Due to the fact that clay-rich soils must be replenished by trucking in gravel, having clay-rich soils increases the cost of the project.
  5. Local health officials will almost certainly require that the septic system be elevated 3-4 feet above the water table.
  6. If your property is located in an area with a high water table, you might expect to pay a higher installation fee.
  7. Your installation expenses will be significantly increased as a result of this.

Who Installs Septic Systems?

A septic system is blocked by a business that is authorized to provide this type of service. Before selecting a septic installation firm, it is critical to conduct due diligence in the same way you would in any other business. Make careful you interview a number of different companies and obtain written estimates. A septic system replacement might cost anywhere from $1,000 to $10,000, depending on the provider you work with. Permitting, installation, and restoration charges for your yard should all be included in the quotation.

Speaking with relatives and friends for recommendations on people they know or with whom they have done business is something I would encourage.

If you’re still having trouble finding what you’re looking for, you may try searching for septic system installers near me, septic system installers nearby, or septic system contractors near me in the Google search engine. If you conduct this type of web search, you should receive some first ideas.

Why Do Septic Systems Fail?

Septic systems, like many other things, will eventually fail to work correctly after many years of use. The way you care for and maintain your system has a huge impact on how long it will endure and perform. For example, having a waste disposal in conjunction with a septic system is strongly discouraged. Food and other garbage are not intended to be flushed down the toilet or into a septic system. Over time, these obstructions can choke leach lines, resulting in a situation in which the system is unable to perform its functions correctly.

Only biodegradable items should be flushed down a toilet, according to EPA guidelines.

By properly maintaining your septic system, you may extend its life expectancy by several years.

Buying and Selling a Home With a Septic System

When purchasing or selling a house, it is essential to have the septic system inspected. It is a substantial obstacle to overcome, much like a house inspection. Nobody wants to purchase a lemon and then have to incur the additional price of replacing a septic system, which might cost thousands of dollars. Septic system inspections are required by law in certain places, and in others they are optional. A requirement known as Title Vrequires a seller in the state of Massachusetts to check their septic system before they may sell their home.

  1. Title V septic inspections are usually between $700 and $1000 in price.
  2. If the seller’s septic system fails the inspection, he or she has two options.
  3. By completing the escrow holdback, the agreed-upon closing date may be maintained uninterrupted.
  4. For example, if the cost of replacing the septic system is $20,000, they will request a holdback of $30,000 from the sale.
  5. Over the years, I’ve sold a number of homes that had a broken septic system, and we finalized the transaction by putting an escrow holdback on the property.
  6. As a result of your actions, you may find yourself in court.

Getting a Septic System Replacement Loan

Is it possible to receive a loan to rebuild your septic system?

This is a question that I’ve received several times throughout the years. Yes, and some governments will also give financial aid in the form of grants. Here is a list of resources that can assist you in obtaining finance for septic system replacement.

You Need a Permit for Your Septic System

It is necessary to get a permission from the county clerk’s office, the environmental or zoning department, or both, before you can begin your installation. Depending on the state you live in, you should anticipate to pay between $300 and $500 for this service. Permits for business usage might cost up to three times as much as residential permits.

When is the Septic Tank Installed During a New Build?

Your contractor will have to wait until the frame of the house is complete before doing the groundwork essential for the installation of the septic system. A hole excavated before to this time may cause problems with the building process and cause it to be delayed. Trucks parking on the lot would have to be carefully positioned in order to prevent hitting the hole, which might jeopardize the work and increase your expenditures. Most of the time, your contractor will include the cost of installing your septic system in the total cost of your project.

Here are some additional questions to ask a builder if you are constructing a home for the very first time.

Video: How to Find Your Septic System

What is the location of your septic system tank? In this video, you will learn some useful suggestions on how to locate your septic system.

What to Know About Septic System Maintenance

Because the cost of septic system installation and the materials necessary is significant, you want to be certain that it lasts as long as possible before replacing it. If it is maintained on a regular basis, you should experience less difficulties with it and it should last longer before it has to be replaced. Pumping and cleaning the tank that will be used to remove the sludge will usually be included in the maintenance schedule. This should help the drain field to endure for a longer period of time before it has to be replaced.

However, if you have a large family of 6 or more individuals, this may be necessary on a yearly basis.

In addition to your geographic location, the cost of tank maintenance is determined by how easy it is to get to the tank.

How Do You Know When a Septic Tank System Needs Replacing?

Septic systems are typically good for 20 to 30 years, and in some cases even longer, before they need to be upgraded or replaced. Some symptoms might suggest that there is an issue with your computer’s operating system.

Green Grass

If you have grass growing over your drain field, does the grass appear to be growing more vigorously than in other areas? Are there any plants in the vicinity that are growing at a higher rate than the rest of the plants? If you can’t identify any other reason for this to be happening, it might be a hint that the drain field isn’t performing as it is supposed to.

Yard Puddles

Having a puddle in your yard despite the fact that it hasn’t rained may indicate that your drain field isn’t performing as planned by the manufacturer.

Assuming that there is an unpleasant stench along with the puddles, you can expect to discover that your septic system has failed.

Flushing Problems

A blocked toilet flush and the appearance of clogged pipes might indicate that there is a problem with the plumbing system in your home. An foul stench in the home might also be an indication that something is wrong with your septic system and needs to be addressed.

Overflowing

A tank that is overflowing indicates that it is not working properly. Septic tanks eventually collapse over time, especially if they have not been serviced on a regular basis.

Contamination

A septic system that does not function properly may cause well water to become contaminated, necessitating the need for immediate repair. If the local board of health determines that your property is filthy and has the potential to infect other properties in the area, they may decide to condemn it.

Cost to Replace a Septic System vs. Installing New

It is possible that you may need to replace your system, and the cost will be more than it would be if you had a new system constructed from the ground up. This might occur as a result of the price connected with the removal of the old system, as well as the possibility of contamination. In some cases, you may discover that all you need to do is replace the pump in order to have your septic system running properly once more. Pumps normally need to be replaced every 10 years and might cost between $1,000 and $2,000 to purchase and install.

When leach fields cease to function as intended, they nearly usually require replacement or repair.

Miscellaneous Septic System Repair Costs

Some components of a septic system may require replacement at some time in the future. Listed below are the options, together with their associated costs:

  • The baffle is a component of the septic tank that prevents the accumulation of scum in the tank’s inlets and outflow pipes. It should be replaced every five years. Approximately $300-600 will be spent to replace it. Tank cover – Because the tank cover is composed of concrete, it is susceptible to deterioration over time. Approximately a few hundred dollars is required to replace one of these devices. a concrete distribution box (also known as a D-box for short) is a smaller tank that is responsible for distributing liquids out to the leach field. The typical cost of replacing a distribution box is between $600 and $1300.

Can You Repair a Septic Leach Field?

Years ago, the answer to this question would have been no; a septic leach field could not be repaired. Today, the answer is yes. Today, it is more likely that you will be able to avoid the costly and time-consuming process of replacing the entire leach field. Septic aeration is a technique that has been developed. It is essentially a matter of adding oxygen to wastewater using aeration machines that dissolve oxygen to encourage aerobic digestion. A classic septic system operates in an anaerobic (oxygen-free) environment, resulting in the formation of a black, sludge-like layer in the leach field known as the biomat.

The septic system eventually fails as a result of this.

It may be built in a short amount of time.

How Septic Aeration Works

As a result of the aerobic bacteria, the amount of nutrients in the septic tank effluent that the biomat needed to survive and develop has been greatly reduced. The biomat eventually succumbs to the elements. Aerobic bacteria that exit the septic tank along with water that contains high amounts of dissolved oxygen feed on the biomat, causing it to shrink even further in size and effectiveness. The mechanism causes the biomat to diminish in size until it is no longer visible on the surface. It will take many weeks for the earth and sidewalls of the leach field to revert to a porous state, and the aerobic septic system will work as if it had just been constructed.

What you avoid with septic aeration is the need to dig up your yard and the expenditure of tens of thousands of dollars.

A septic system firm in your area should be able to offer you with such information as well. terralift aeration is a technique that may be used to treat a septic system in addition to the other methods mentioned.

Final Thoughts on The Costs of Septic Systems

In the construction of a home, septic systems are one of the most expensive components that must be purchased and installed. The cost of replacing a septic system can be quite expensive. Unfortunately, when it comes to increasing the market value of your property, rebuilding your septic system has minimal effect. This investment yields a poor return on its initial investment. A new septic system is not likely to have a substantial influence on the value of your house. This advice on the cost of replacing a septic tank and leach field should have been beneficial to you, and we hope you found it so.

If you need to reach Bill, you may do so through email at [email protected] or by phone at 508-625-0191.

Are you contemplating the sale of your home?

The following towns in Metrowest Massachusetts are served by my Real Estate Sales: Ashland; Bellingham; Douglas; Framingham; Franklin; Grafton; Holliston; Hopkinton; Hopedale; Medway; Mendon; Milford; Millbury; Millville; Natick; Northborough; Northbridge; Shrewsbury; Southborough; Sutton; Wayland; Westborough; Whitinsville; Worcester; Upton; and Uxbridge MA.

DescriptionFind out how much it costs to install a new septic system as well as how much it costs to replace an old septic system in this article.

Name of the publisher Real Estate Exposure to the Fullest Extent Logo of the publisher

Leave a Comment

Your email address will not be published. Required fields are marked *