How Do I Locate My Septic Tank? (TOP 5 Tips)

Go to your basement or crawl space, and then look for the main sewer line that leads to your septic tank. Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside.

How to find out if my house has a septic tank?

• Inspect your property carefully. Some septic tanks,especially if you live in a mobile home,are easy to spot because they are accompanied by a large,rectangular or
• Consider the location of your home. Sewer systems are not cheap,and the area has to have enough homes to support the system’s maintenance.
• Check your bills. Sewer systems are not free,so if your house is attached to a community sewer system,you can expect to be getting bills from it.
• Get a copy of the records for your property from your municipal government.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

How do you find a septic tank in an old house?

Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.

Can a metal detector find a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

How far is septic tank from house?

Local codes and regulations that stipulate the distance of the septic tank from the house vary depending on the locale, but the typical minimum distance is 10 feet.

How do I find my septic tank lid?

You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath.

How do I find out if my septic tank is registered?

Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Can I drive over my leach field?

Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.

Are septic tanks made of metal?

The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.

Does shower water go into septic tank?

From your house to the tank: Most, but not all, septic systems operate via gravity to the septic tank. Each time a toilet is flushed, water is turned on or you take a shower, the water and waste flows via gravity through the plumbing system in your house and ends up in the septic tank.

How deep should a septic tank be?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

Can I build a deck over my septic tank?

You should never build a deck over a septic field; doing so will prevent the natural draining and dissipation of the effluent. This can ruin the septic system, not to mention releasing foul smells into the air all around your deck. The dissipating effluent can also rot the deck from underneath.

How To Find Septic Tank Location: A Guide for Property Owners

The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.

Follow the Main Sewer Line

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.

Inspect Your Property

Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.

If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.

Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.

• Paved surfaces
• Unique landscaping
• Your water well, if you have one
• And other features.

If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.

Check the Property Records

Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.

Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.

Don’t Try to Fix Septic Tank Issues Yourself

Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.

Schedule Septic Tank Maintenance

The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.

We are open seven days a week, twenty-four hours a day.

Frequently Asked Questions

A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.

How do I know if I have a septic tank?

Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.

If you’re also using well water, it’s possible that you won’t receive one at all.

What do I do once I locate my septic tank?

Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.

This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.

Then contact The Original Plumber to have your septic system maintained on a regular basis. Preventing worse problems and the need for costly repairs down the line may be accomplished via proper septic system maintenance. All of the heavy lifting has been delegated to our team of professionals.

How To Find My Septic Tank

1. What is a septic tank
2. How do I know if I have a septic tank
3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

1. “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
2. When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
3. The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
4. In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

• A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
• A septic system is likely to be installed in your home if you reside in a rather rural location.
• Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
• When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
• Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

1. If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
2. The county health department is responsible for keeping track of septic systems.
3. A septic tank’s position could be depicted on a survey map, for example.
4. The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

• In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
• By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
• The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
• Going via the sewage line itself is another method of locating the septic tank utilizing it.
• Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
• When the snake comes to a complete halt, it has almost certainly reached the tank.
• While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
• When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

• Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
• Directly in front of the home Immediately adjacent to your well (if you have one)
• In close proximity to trees or densely planted regions
• In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start looking for clues as to where it might be hiding in plain sight. Keep your eyes peeled as you walk around your property, looking for any unexplained high or low points that could indicate the presence of a buried tank. When looking at your property, you might notice a hill or mound on the ground, which is often an indication that there is a septic tank nearby. One more thing to consider when searching for the right septic tank for your home is the amount of grass or other greenery in your yard.

Or, if the tank was not buried properly, you might notice a “bald patch,” or an area where the grass is having a hard time growing.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job

Looking for Your Septic Tank? Here’s How to Find It

“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved.

Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property. If you’re looking for a tank, we have some suggestions that may be of assistance.

Why you need to know where your septic tank is located

If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.

In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.

How to find your septic tank

1. Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
2. Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.

After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.

• The post was published on July 16, 2019 under the category Septic Tank System.

How Do I Find My Septic Tank

What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00

How Do I Find My Septic Tank

Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.

A tiny proportion of septic tanks have a capacity of 3000L or more.

Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.

If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

1. They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
2. Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
3. A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
4. Using an electronic service locator, you may locate a septic tank.
5. In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
6. Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
7. Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

• There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.

Check the rest of the toilets in the home by repeating the procedure.

Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.

a link to the page’s load

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

1. 3.
2. Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
3. Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
4. When you do, that’s when your septic tank comes into play!
5. Look for the Lid.
6. You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
7. Those areas should be excavated in order to disclose the lids.
8. Get in touch with the pros.
9. Lifting concrete lids will necessitate the use of specialized equipment.
10. A fall into an unprotected septic tank has the potential to be lethal.
11. Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

How to Find Your Septic Tank

Many folks have contacted me through e-mail (typically from across the nation) to inquire about the location of their septic tank. “I have no idea,” I generally say as a helpful response to the question. I really want to add something like, “It’s just off your driveway, near that bushy thing,” or anything along those lines. But, truly, even for the most experienced searchers, septic tanks are difficult to come by. The following are some strategies you might employ to assist you in locating your tank.

• Precaution should be exercised before you get started.
• So, proceed with caution!
• Please let me know if you have any queries or need assistance.
• Get to know the beast!
• tanks are normally buried 4 inches to 4 feet below the surface of the ground.
• You might be astonished to hear that someone knows exactly where it is hidden in plain sight.
• It is against the law to dig or probe in your own yard without first locating and marking the underground services.

You will receive the following tools to aid you in your search: Measurement tape, tile probe, and a shovel (if you are ambitious) The following tools are required: a metal detector (borrow or rent one since septic tanks often include iron steel rebar in the lids), and a hoagie sandwich (because locating sewage tanks makes you hungry.trust me on this).

• Examine the basement wall to see where all of the pipes join together and exit through the basement ceiling.
• If you don’t have a basement, walk outdoors and check for the roof vents on your house.
• Ordinarily, the sewage line that leads to the septic tank will exit the home right below this ventilation opening.
• On sometimes, the ancient proverb “The grass is always greener on the other side of the septic tank” is true.

Your tank may be located by probing or digging for it, and with luck, you will locate it. Keep in mind that not everything that seems to be a septic tank actually is! It’s possible that you came upon one of the following instead:

• Rubble buried in the ground (not to be confused with Barney Ruble)
• SepticDrywell
• An old foundation
• In case you happen to live in a cemetery (which is spooky), you may use a grave vault to keep your belongings safe.

After a few hours of hopelessly digging about in your yard, it will be time to eat your hoagie and take a little sleep. Following that, it will be necessary to rent or borrow a metal detector. In the event that your next-door neighbor loves Star Wars action figures or has more than three unidentified antennae on his roof, there is a significant probability that you can borrow his metal detector. If you’re lucky, the metal detector will really assist you in finding your septic tank, rather than simply a bunch of old buried automobile parts.

• According to local legend, a pumper known as “Zarzar The Incredible” can locate sewage tanks using a metal measuring tape spanning 30 feet in length.
• Continue to press your commode (“commode” sounds sophisticated) tape deeper and farther down the pipes until he “feels” the bottom of the tank with his tape.
• I recently acquired locate equipment that can be used to locate septic tanks, and I’m excited about it.
• For further information, please contact me at 574-533-1470.
• After that, you may have a movie of the inside of your sewer pipes created!
• Related: Visit our Septic System Maintenance page for more information.
• Services provided by Meade Septic Design Inc.
• Both Clients and Projects are included.
• Send me an email!

How to locate your septic tank and your drainfield

Septic systems on-site are used for accepting and treating wastewater in homes that are not linked to the municipal wastewater management system. A septic system is comprised of three components: a septic tank, a drain field, and piping. As a homeowner, it is your responsibility to properly operate and maintain your septic system in order to avoid system failure. For example, depending on the legislation in your area, you may be compelled to pump it on a regular basis. It is impossible to perform maintenance operations, however, if you do not know where the tank is located.

Steps to follow to locate your septic tank and drain field

The contractor that designed and constructed the septic tank on your property should have submitted an as-built diagram with the local health authority before starting work on the project. In the event that you have the contractor’s contact information, you can ask them for a schematic, which you can then use to pinpoint the location of your septic tank. If you do not have a copy of the schematic, you can request one from the local authorities. Depending on whether the installed system included electrical components, the schematic may be available at the regional building department offices.

When it comes to pinpointing the exact placement of your septic tank and drain field, this graphic may be quite helpful. If you are unable to locate the tank using this diagram, you will need to do more research on the land in order to determine its position.

The sewage outlet pipe is an excellent spot to start your physical evaluation of the property because it is accessible from the outside. This pipe is commonly found in the basement of a home, and it is a 4″ black pipe with a cleanout at the bottom. If the cleanout is behind a wall or in a closet, it is considered a hidden location. Simply look for possible access coverings or a structure that might be concealing it. Lift pumps are sometimes installed in basements to assist in pumping sewage from the building.

1. Having discovered it, flush a toilet and listen to the pump to determine where the sewage is being discharged.
2. You should now be able to see the general orientation of the septic tank and drain field from this point.
3. The septic tank will be located a few meters away from the home, and the outflow pipe may be at an angle of 30 or 45 degrees from the house.
4. Work your way around the home in a circle, starting at an electrical outlet and continuing until you find the septic tank.

Tips for locating your septic tank

The lid of the septic tank should be visible. In some cases, a septic tank riser may have been installed and that will make it easy to locate your septic tank. But it is also possible that the septic tank lid could be underground especially for old houses. The following tips can help you locate the septic tank in such and other related scenarios.

• It may be possible to discover the septic tank lid underneath using a metal detector if it is buried. Prevent wearing footwear that contains steel or any other metal in order to avoid interfering with the readings of the detector
• Instead, you can use a flushable transmitter that is flushed down the toilet and then tracked with a receiver. When it comes to septic tanks, the strongest signal will be seen close to the intake region of the tank.

Depending on whether the septic tank is above or below ground, you may have to dig to get to it. Construction materials for septic tanks include concrete, fiberglass, or plastic, and their shapes can range from oblong to cylindrical to rectangular. The majority of modern septic tanks will have their lids positioned in the center of the tank, and the lid should be within three feet of the ground surface in most cases. However, depending on a variety of conditions, such as farming and other human activities on the property, it is conceivable that it will be significantly deeper.

Additionally, you may use a small steel rod to probe the earth in order to pinpoint exactly where the tank is located as you continue digging.

Inspecting the tank

It is critical to thoroughly inspect and evaluate your septic tank and its contents when it has been identified. First and foremost, you may unscrew the lid to inspect the scum and sludge layer beneath it. In addition, the use of tracer dye tablets allows you to check the septic tank without having to dig it up. If you use tracer dye pills, all you have to do is flush them down the toilet and wait for a maximum of two days. Because of the way the tablets dissolve in water, if there is a problem with the septic system, you will see that the leach field has a glowing green hue surrounding it.

It is possible that someone will fall into the tank, causing significant damage or possibly death. Additionally, all septic tank maintenance techniques should be carried out in accordance with the legislation governing the sewage system.

Conclusion

You can identify your septic tank without assistance from a professional, but it is a good idea to have someone who is properly educated in septic tank maintenance examine and maintain your septic tank on your behalf. The effluent filter in your tank should be washed into the open septic tank rather than on the ground in your yard if your tank has one. It may also be a good idea to make a note of the position of the septic tank when it has been discovered. This will be beneficial to anyone else who may require access to the septic tank in the future.

Septic tanks release combustible and hazardous gases, and as a result, they must be located in an open area.

How To Locate a Septic Tank

Customers frequently inquire about the location of a septic tank. Unless your septic tank is equipped with special risers that elevate the lids above ground level, you may need to enlist the assistance of a qualified professional. However, there are a number of things you may do to prepare yourself before calling for assistance. When it comes time to have your septic system repaired, being how to find your own septic system will save you money. Public health records can be obtained by contacting your local health department.

1. These permits should be accompanied by a graphic depicting the location of the septic system’s burying spot.
2. Public Records Request for the County of Nevada Request for Public Records from the County of Placer Examine the findings of your inspection report.
3. Make contact with the construction company that built your home.
4. Find the location of the main sewer line.
5. Locate the 4 inch sewer pipe that runs through your basement or crawlspace and take a measurement of the point at which it leaves the home.
6. By carefully probing the yard every few feet and following the septic pipe across your yard, you should be able to detect any problems.
7. The majority of septic tanks are placed 1 to 3 feet below and are located roughly 10 to 20 feet away from the house.

An electronic metal detector can find the reinforcing bars in a concrete tank if it is built out of concrete.

Please contact us.

We have specialized technology that we can use to pinpoint the location of your tank.

You should make a note of the position of your tank for future reference if you were successful in discovering it.

A riser elevates the septic lid above the ground, making it easier to find and access your septic tank and its contents.

As a result, you will not have to pay a professional to identify and dig up the lids every time your septic system is repaired, which will help to protect your landscape and save you money.

How to Find a Septic Tank With a Metal Detector

For sewage treatment in the United States, around 48% of households in rural and outlying regions depend on septic tanks or septic systems. Many of these systems have been operating without regular maintenance for many years. It is necessary to locate your septic tank in the event that sewage is backing up into your home or if your main drain line has become obstructed. Throughout this post, we’ll go over the basics of how septic systems function before showing you how to identify your septic tank in six simple stages.

How do septic systems work?

A septic system is made up of two parts: the septic tank and the drain field (or leach field).

Septic Tank

Waste from toilets, sinks, and showers is sent down a main sewage line and into a holding tank known as the septic tank. A septic tank is a large, subterranean container that acts as the initial stage of a home’s sewage treatment system by collecting and treating sewage. Watertight containers such as concrete, steel, plastic, and fiberglass are used to construct the tank. Until the particles and liquids separate into three different layers, sewage is allowed to remain in the septic tank. This picture shows how sewage from the home drains into a two-compartment underground septic tank.

The liquid wastes are subsequently discharged into the drain field.

The bacteria produce a sludge that is “digested” and stays in the tank until it is drained.

This stratum is referred to as effluent in most circles.

Drain Field

Drain fields are composed of layers of gravel and dirt that allow liquid sewage to flow down. It eventually becomes part of the groundwater supply. Aerobic bacteria (bacteria that require oxygen to survive) and other microbes decompose the organic debris that remains.

What happens if a septic tank gets too full?

In the event that your septic tank becomes overflowing, sewage may back up into your home. It is more difficult to breakdown sludge than it is to collect it. If the sludge isn’t cleaned, the solids will build up until they overflow into the drain field, causing the drain to back up. This has the potential to clog pipes and produce a backup. The sludge must be cleared on a regular basis in order to avoid this.

Many households only get their tanks emptied after the system malfunctions. Waiting until that stage can result in repair expenses in the tens of thousands of dollars. Every three to five years, we suggest that you have your septic tank pumped.

6 Steps to Locate a Septic Tank

Water from your toilets, sinks, and showers is collected in a main drain pipe and disposed of properly. This line departs your home and enters your septic tank through the basement or crawl area where it was installed. Find the line in question. Afterwards, walk outside and look for the identical location on the opposite side of the wall. Make a note of this spot since you’ll need it in a moment.

2. Check Permits and Public Records

The majority of county health agencies keep public records of septic system installation permits on their websites. These permits must be accompanied by a schematic or design depicting the proposed location of the septic tank and drainage field systems. They also give a description of the tank’s dimensions and construction material. Having this information can be quite beneficial when trying to locate a submerged tank lid. In some cases, depending on the age of your septic system and the digitization efforts of your county’s health department, you may be able to do a public records search online.

If you live in Colorado, we’ve provided links below that will allow you to check septic records in a few different areas.

• Colorado’s counties of Adams, Arapahoe, and Douglas Colorado Septic Records Search
• Colorado Permits Search
• El Paso County Records Search
• Jefferson County Septic Records Search
• Jefferson County Records Search
• Mesa County Septic Systems Search
• Pueblo County Records Search. Colorado Septic Records Search
• Pueblo County Records Search

3. Determine Septic Tank Material

If you’ve located your septic permit, you’ll find information about the size, shape, and material of your septic tank there as well. But don’t be concerned if your septic data aren’t readily available. We can perform some basic detective work to determine what material your septic system is built of. Let’s start with a look at the materials.

Types of Septic Tank Materials

Construction of septic tanks is mostly done using four types of materials: concrete, steel, fiberglass, and polyethylene plastic. Until the 1880s, the most extensively used septic tank material was concrete, which was then replaced by steel. These tanks have a lifespan of around 40 years and are built to last. They are susceptible to cracking, however, in locations where temperature variations are strong and frequent. Concrete tanks are frequently required by municipalities that have strict requirements on septic system construction.

• Steel septic tanks begin to corrode within 20 to 25 years of installation in most regions.
• If a human or animal walks across the weakened tank, it may collapse under the weight of the person or animal.
• They will not break or corrode, however, in contrast to concrete or steel tanks.
• PlasticSeptic tanks made of polyethylene have been in use since the 1980s.

They are not susceptible to rusting and are less prone to break when compared to concrete. They are, however, not quite as long-lasting. Because of the weight of the earth above them, or because a vehicle passes over the area where they are buried, plastic tanks are susceptible to collapse.

How Old is Your House?

Next, let’s determine the approximate age of your home. In some cases, all you need to do is take a glance at the house’s façade to get an idea of how old it really is. However, you may examine the tax assessor’s records in your county to get a more precise assessment. Similarly to searching for septic records, your mileage may vary depending on which county’s digitized documents you are searching for. Let’s go over an example search utilizing Boulder County’s Property Search tool so that you can have a better sense of what you should be looking for.

1. Look up your home address on the internet. When searching for a home, some programs provide separate areas for your address and street name, while others (such as Boulder County) merge the two into a single search box. Look for information on Deeds and/or Sales Records in the public domain. You’ll find a list of transactions here, with dates showing when the property was purchased and sold. Find the transaction that occurred on the earliest possible date. This is most likely the year in which your home was constructed.

This information allows you to make an informed guess regarding the sort of material that your septic tank is built of.

4A. If it’s Concrete or Steel, Use a Metal Detector

After coming to the conclusion that the tank is most likely built of concrete or steel in Step 3, a metal detector may be used to make the work of locating it much simpler. But not just any metal detector will do. It must be the right one. Standard metal detectors have a depth range of 6 – 8″ (15 – 20 cm) below the surface of the ground. As previously stated, the majority of septic tanks are placed 1′ to 3′ (0.3 m to 1 m) underground, putting them outside of the acceptable range. An advanced sort of metal detector known as a Magnetic Locator, which can detect objects as deep as 16′ (4.8 m), is available for purchase.

How to Use a Metal Detector to Search for a Septic Tank

If you have a septic permit record, you may refer to it to figure out how far you need to go to install a septic tank. Start at the point where the drain line meets the home and work your way out to where the septic tank is shown on the diagram. Keep in mind that this graphic depicts the proposed installation area and may not accurately depict the actual ground conditions on the site. We’ll have a look at the illustration below. One inch (2.5 centimeters) is equivalent to fifty feet (50 meters).

By using a ruler to measure the design, we’ve determined that the septic tank should be roughly 13′ (3.96 m) away from the home.

1. To begin, start at the location you highlighted in Step 1 where the sewage drain line leaves the home. From here, you may switch on the locator and adjust the gain to a high setting. Walking over the search area, sweep the locator from left to right, as if looking for anything. As you go, make a note of the regions with the strongest signal strength. It is most likely that the tank-iron lid’s handles will be located in one of these positions
2. As soon as you’ve exhausted the search region in one direction, sweep over it perpendicularly and make note of the spots with the strongest signal strength. Continue on to Step 5

4B. If it’s Plastic or Fiberglass, Probe Gently

Septic tanks made of plastic or fiberglass are typically buried one to two feet (0.3 to 0.91 m) below ground level. They feature circular covers made of green or black plastic that are roughly two feet (0.91 m) wide and have a diameter of around two feet (0.91 m). Due to the fact that these tanks are totally made of plastic, a metal detector will not be of use in locating them. In this situation, a soil probe is really useful. An inexpensive soil sampling instrument, soil probes are comprised of a 4′ (1.2 m) metal rod with a pointed tip on one end and are used for soil sample.

Gently poke the earth with a soil probe every 2 to 3 feet, using a light touch (0.61 to 0.91 m).

Make a note of any areas where you encounter resistance and continue exploring around in your search area. The use of a soft touch is essential here, since the metal tip of the probe can cause damage to plastic septic tanks (and sewage lines) if too much force is used.

5. Time to Dig

Following the placement of an amagnetic locator (or the probing of the ground) to record the places with the highest signal strength, you are ready to begin digging. Septic tank lids can be located anywhere from 4″ (10 cm) to 4′ (1.2 m) below the surface of the ground.

6. Mark the Location for Future Maintenance

Having discovered your septic tank, you’ll want to ensure that it can be readily detected and accessed in the event that it has to be repaired or replaced. You may accomplish this by installing a septic tank riser. Sewage Tank Risers are devices that provide for easy access to the septic tank from the ground. They are shafts made of plastic or concrete that link the top of the tank to the surface of the ground below the tank. The tank lid will no longer require you to dig to access it whenever maintenance is required.