How much do concrete septic tank lids cost?
- Concrete septic tank lids are more expensive. They are usually priced closer to $70. Still, one can argue that the added durability is well worth the additional bucks. Do note that the prices mentioned above are just for the replacement lids. You’ll have to pay an additional fee to get the lid professionally installed.
How much is a concrete septic tank riser?
The cost of a septic tank riser can vary, depending on the size, the material, the style, and your installer. Plan on spending at least $150 for a basic model, but know that they can cost up to $400, depending on the model you choose.
How much does a concrete riser cost?
Plastic septic tank risers typically cost $300 to $400 to install, parts and labor included. Concrete risers are more durable but also more expensive, and the cost will depend on the quote you receive from the installing contractor.
Can you pour concrete over septic tank?
It is never recommended to build a structure over any portion of your septic system. No permanent structures should be built over any portion of the system, but at least in this case the homeowner can pump out their septic tank.
Why does my septic tank have 2 lids?
Solid, watertight, buried tank made of concrete, plastic, fiberglass or metal. This tank has a way in (inlet), and a way out (outlet). So, most residential tanks should have (2) lids about 5′ away from each other. A septic tank holds all the liquid waste from your home (toilets, sinks, kitchen, bathtubs, floor drains).
How many lids should a concrete septic tank have?
Two or three lids may be included in your system. The average size of a sewage tank is approximately 5 feet by 8 feet. The lid is buried between 4 inches and 4 feet underground in most cases.
Should septic tank lid be sealed?
Like wells, septic systems have problems if they are not sealed from outside surface water. Most septic systems rely on buried pipes to get rid of the fluids. The lid covers should fit tightly — if they don’t, a company that specializes in septic repairs should be called to fix them.
Should septic tank lids be buried?
In most cases, all components of the septic tank including the lid are buried between 4 inches and 4 feet underground. Unless the septic tank has special risers that position the lid at ground level, you’ll have to dig for it.
Are septic risers worth it?
Having a riser in place can also significantly reduce the cost of septic tank maintenance over time through the ease of access and time on the job saved. Plus you will be spared digging up your lawn every time as well.
How many septic tank risers do I need?
A single riser is required for accessing the pump chamber for this type of system. If you don’t have two additional risers, you should locate your septic tank and install risers for both the inlet and outlet openings, as described above.
Do they make square risers for septic tanks?
The Polylok square riser adapter ring is designed to connect the Polylok septic tank risers or lids to an existing concrete tank with large square or round openings.
Septic Tank Risers, Lids, and Covers
Septic tank risers are intended to replace existing concrete, fiberglass, or metal septic tank lids by lowering the entrance to the ground level and allowing for better drainage. Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.
With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!
Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water?
It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.
With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!
FREQUENTLY ASKED QUESTIONS
The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered! Would the POLYLOK SEPTIC TANK LID fit directly on the ADAPTER RING, or will I need to use a RISER to ensure a proper fit on the tank? With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength.
- Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter.
- ALL other Polylok lids will attach straight to the adapter ring, eliminating the need for a riser or any other adaptor.
- No.
- Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.
- It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade.
- IS IT BETTER TO USE THE STANDARD LID OR THE HEAVY DUTY LID?
- If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended.
- Yes.
IS IT INCLUDED WITH THE POLYLOK SEPTIC TANK RISERS AND LIDS TO USE SCREWS? Yes. The Polylok Septic Tank Risers are assembled using stainless steel screws that allow them to be connected to one another. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].
THE POLYLOK SEPTIC TANK RISER ADVANTAGE
Riser systems are available in a variety of shapes, sizes, and designs on the market today. The Polylok septic tank risers are, without a doubt, the best money can buy in this category. There are several causes for this, but the following are the most significant:
FACTORY INSTALLED GASKETS
The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.
INTERNAL STRUCTURAL RIBS
The Polylok risers are reinforced with structural ribs that run internally around each riser segment, providing them with exceptional strength and allowing them to maintain their shape even after the hole is backfilled with dirt. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.
LOW PROFILE RISER LIDS WITH HANDLES
The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.
LARGE TANK ADAPTER RING
It is necessary to use an adapter ring in order to attach risers to your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!
STAINLESS STEEL SCREWS INCLUDED
At Septic Solutions, we strive to make the buying and installation process as simple as possible for our customers. All of our Polylok risers and lids are delivered with all of the stainless steel screws required for installation in one package.
Concrete Septic Tanks – Residential & Commercial
When it comes to wastewater management, J R Precast concrete septic products continue to be the industry standard due to their strength, ease of installation, serviceability, and efficiency, regardless of whether you are repairing or installing a new septic system. Only the highest-quality and most lasting precast septic products are designed, manufactured, and distributed by J R Precast, which continues to be based in Southern New England. Each and every one of J R Concrete’s precast concrete products is manufactured to meet or exceed all applicable state and ASTM requirements.
We have been the industry leader in precast concrete in Southeastern Massachusetts for more than 50 years because we base our engineering designs and production techniques on concrete concepts that have been proved time and time again to prevent failures.
All of our wastewater management solutions have been field-tested and confirmed to be the best available for the most demanding circumstances and applications in New England. Oil Water Separators, Grease Traps, and Interceptors are other terms for the same thing.
Septic Tank Risers
We frequently receive inquiries from clients who have an older septic tank and are seeking for a means to gain access to the tank from the surface. Many times, all that is present is a concrete cap over the opening that allows entry. When used in conjunction with an adapter ring, joint sealant, and tapcon screws, either of the risers mentioned above can be used as a substitute in this situation. Alternatively, we create concrete slabs with a riser cast into them, which may be used to quickly replace existing lids on a variety of containers.
- An adhesive or sealer such as a mastic rope can be used to attach the new concrete lid to the existing concrete tank, which will help to prevent leakage.
- The diagram below demonstrates what these risers look like and also contains their measurements for your convenience.
- When determining the size of the slab that will be used to cover your access hole, start by measuring the longest span of the hole.
- To account for the height of the replacement riser, subtract approximately 6 or 7 inches from the total height.
Tuf-Tite Septic Tank Riser, 24’x12′ – – Amazon.com
On July 14, 2018, a reviewer in the United States of America verified that they had made the purchase. All of the products in the shot were purchased by myself. I needed to install an RV sewer hookup, and this was the most environmentally friendly method. No more digging around for the lid when it comes to pump out time! 5.0 stars out of 5 for this product It’s a good fit. On July 14, 2018, Stephanie Stanley posted a blog entry. All of the products in the shot were purchased by myself. I needed to install an RV sewer hookup, and this was the most environmentally friendly method.
- The photographs in this review On December 30, 2017, a review was conducted in the United States.
- It was necessary to first install an adapter ring to the tank riser in order to adhere the risers to the septic tank, then an extra 24 x 6 riser to provide additional height, and lastly a 24 inch flat lid to complete the installation.
- Furthermore, if your septic system requires maintenance in the winter, there will be no digging in frozen earth.
- Made to be extremely durable.
- 5.0 stars out of 5 for this product A must-haveDurable and long-lasting Posted on December 30, 2017 by DM This is an absolute must-have if you want to get to your septic tank quickly for maintenance.
- You’ll never have to dig yourself out of a hole again.
- Simple to set up.
We eventually painted the lid a brownish color to match the surrounding landscape, which was an option.
In order to keep the adapter ring from moving about, I used cement sealing caulk on the bottom lip and then quick dry cement around the bottom edge.
It worked out well and was built to last.
On April 28, 2016, Justin posted a blog entry.
In order to keep the adapter ring from moving about, I used cement sealing caulk on the bottom lip and then quick dry cement around the bottom edge.
It worked out well and was built to last.
Purchase that has been verified I purchased and installed two of these Tuf-Tite risers on my septic tank to replace the concrete lids that were previously there.
In order to keep the water out, I utilized concrete anchors for the adapter ring and putty tape underneath the ring.
I elected to bury the risers approximately 6″ below the surface of the ground and designate their location with a surface marker.
The grass will eventually cover everything, and no one will be able to tell what is going on until the septic tank needs to be pumped again.
Because they would not come off no matter how much pressure I exerted, I was forced to chisel the concrete “lids” off my septic tank.
As a whole, this was around a $300 repair for two risers that should hopefully last the lifetime of the septic tank.
Purchase that has been verified The two of them that I bought will be installed on my septic tank.
The second one arrived a few days later, but it was so deformed (it was in the shape of an oval) that it couldn’t be fitted into the TAR or lid.
I tested the riser with a tape measure and it measured more than 25 inches across at one point and less than 23 inches across the other axis.
In the image, you can see it after I used massive wood clamps to mold it into a spherical enough form to be placed on the TAR.
The lack of quality control and the oval forms of many risers have caused my project to be delayed by more than a week, according to my estimates.
3.0 stars out of 5 for this product Poor quality control and a high number of returns On March 7, 2021, M.D.U.
The first one was excellent; it was a perfect fit for the flat lid and tank adapter ring (TAR).
Amazon issued a replacement, which arrived with the same oval watp as the original.
This lid will fit (barely), but I was unable to get the shape to fit into the TAR without the use of clamps (which do not fit into the hole when installing the risers) because of the form of the lid.
I like that Amazon makes it simple to exchange items, but yeesh.
Hopefully, the third replacement will be successful!
Purchase that has been verified Mine was a little oval, maybe 2 inches out of round, when it came.
There were also screws missing.
Insert the riser into the hole.
Continue to fill the hole with dirt and pack it down until it is full.
It is possible to pack a bit harder on the sides that are bent ‘outward’ if you know which ones they are.
Mine went from being 2″ out of round to being 1/16″ out of round using this procedure.
Purchase that has been verified The Polylok riser base and cover are in the possession of a neighbor.
The TuffTIght base and Riser are well-matched, however the screw points on the lid may be improved.
In addition, the lid specifies that it includes the safety screws, and the lid’s documentation specifies that all screws are included, when they are not in fact.
On September 26, 2019, a verified purchase was reviewed in the United States.
We had finally located the lid, but there was no way we were going to cover it and risk having to dig through this muck once more.
Everything arrived in record time, and the installation was straightforward.
It makes life a whole lot simpler.
By RaeraeandMikeysmom on September 26, 2019First and foremost, let me state unequivocally that digging for your septic tank while experiencing a problem with it is a complete nightmare.
That’s when we made the decision to put in the riser.
Everything arrived in record time, and the installation was straightforward. If you don’t already have one of these and find yourself digging every time you go outside, I strongly advise you to get one installed. It makes life a whole lot simpler. The photographs in this review
Best Price on Septic Tank Risers & Covers Online Guarenteed!
Septic Tank Risers and Lids are available from TGWasteWater in a variety of sizes and styles. We also provide a large selection of accessories for our riser products. Are you fed up with having to pay to have your system dug up and pumped every time it needs to be refilled? Are your present concrete risers at danger of collapsing? Is it becoming tiresome to have to lift a hefty concrete cover every time you need to access your tank? It is possible that you responded yes to any of these questions and that you should think about putting a riser system on your septic tank.
- Risers from Tuf-Tite and Polylok are available for purchase.
- Please keep in mind that Tuf-TitePolylok products are incompatible with one another.
- Consequently, if you want us to utilize a Tuf-Tite lid, you must purchase Tuf-Tite Risers, and the reverse is true.
- PLEASE CLICK HERE TO READ OUR INSTRUCTION GUIDE ON HOW TO INSTALL RISERS ON A CONCRETE SEPTIC TANK
Risers & Adapters « The Septic Store
Regardless of whether your septic tank is made of plastic or concrete, it will need to be pumped every 3-5 years. If your tank is buried, this will necessitate the excavation of the site. By utilizing risers and tank adapters, you can elevate the lids of your concrete or plastic tank up to grade, allowing you to access the tank all year long for pumping, filter cleaning, and any other necessary maintenance. Having a clog and backup in your tank in January is something you don’t want to happen to you.
Polylok Adapters
Tank adapters and adapter rings are available from Polylok for the conversion of concrete and plastic tanks. It is possible to prepare your current tank for the Polylok riser system and lids by fitting the adapters on the tank’s existing risers. Available in two sizes: 20′′ and 24′′ in diameter.
Orenco AdaptersLids
In addition to concrete tank conversions, Orenco also provides solutions for plastic tank conversions. Their heavy-duty fiberglass adapters and lids are intended to operate with IPEX’s ultrarib or perma-lok pipe, which are both extremely robust and long-lasting.
EZset
Infiltrator Systems manufactures a product known as EZset. EZset not only serves as the principal riser system for Infiltrator’s brand of IM and TW series tanks, but it also provides tank adapters and lids for use when converting an existing concrete tank into a storage tank.
Premier Tech
Premier Tech’s tank adapter is one of the most substantial on the market. There are certain concrete tanks that have existing apertures that are bigger than the normal 30′′ tank adapter can handle.
Septic System Components
- To allow heavy solids or light greases to separate from sewage by allowing time and space for this to occur
- By using baffles and outlet tees, it is possible to direct effluent (discharge liquid) from the cleanest portion of the tank to the cleanest portion of the tank, resulting in up to a 60% reduction of undesirable solids and contaminants
- To provide a place for anaerobic (non-air breathing) bacteria to break down sewage, resulting in up to a 60% reduction of undesirable solids and contaminants
Components of a Typical Private Septic System
An underground waterproof container with a typical volume in excess of 750 gallons, plus air and scum space equal to roughly 25% of the water capacity. SEPTIC TANK: To avoid direct flow-through, the tank should be blocked or (ideally) segregated, and each compartment should have a riser to grade for cleaning. The tank should be constructed of a sturdy material that is robust enough to handle the weight of the earth and pedestrians. Selvage 5″ of concrete is used to support the concrete tanks and lids, which are designed to take 24″ risers to allow for easy inspection and thorough cleaning.
- TRANSFER VALVE: A diversion valve is a tiny box with one intake and two exits, with a diversion valve allowing you to alternate the outgoing flow.
- CONCRETE DISTRIBUTION BOX: A tiny concrete box with a single input and several exits for dispersing the flow of wastewater to multiple lines of a dispersal field.
- DISPERSAL FIELD (also known as a Leach Bed or Leach Field): A field used for the dispersal of waste.
- The field is built up of large trenches that are roughly 2 feet deep and are usually measured in lineal feet ranging from 12″ to 36″.
- Using the perforated pipe, the effluent is disseminated over top of the bed, where aerobic bacteria are present and work to clean the wastewater as it passes through.
- A 10′ x 20′ filter bed would have a surface area of 200 square feet, which is the standard unit of measurement for surface area.
- Because of shallow bedrock, shallow groundwater, and other factors, holding tanks are utilized in situations when an on-site wastewater disposal system cannot be placed on the land.
- Waste is transported to a landfill or a municipal treatment facility that has been permitted.
a container for collecting effluent, a pump or a siphon are used to lift or disperse fluid to a dispersal field, filter bed, or point of release. Lift stations are utilized in situations when flooding of a field or filter is desired, or where altitudes prevent gravity flow from taking place.
Septic System Components in Santa Rosa
Selling Septic Tanks in Santa Rosa, Petaluma, Vallejo, Napa, Novato, Rosenberg, Fairfield, and surrounding areas San Rafael is a city in the state of California.
Septic Tanks
The residential septic tanks we manufacture are made of precast concrete, providing homeowners in New England with a dependable wastewater management system. Shea’s precast concrete septic tanks are sturdy, waterproof, and ecologically friendly, making them an excellent choice for any home waste management system in the world. These precast septic tanks are manufactured to your specifications and are also simple to install in your house or business. For more information about our precast concrete residential septic tanks, please contact Shea Concrete Products at (800) 696-SHEA.
Take a look at the Case Study
Septic Tank 1000 Gallon
Listed below is a list of the septic tanks, chlorine contact tanks, and siphon dose tank packages thatCamden Supplyoffers, along with detailed descriptions of their features and specifications. Please call Camden Supply and chat with one of our staff if you require further information on a certain product.
Single Compartment Septic Tanks
A one-compartment steel-reinforced concrete septic tank, according to the script. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 56 inches
- Overall length is 79 inches
- Overall width is 48 inches
- Height to center line of inlet is 48 inches
- Height to center line of outflow is 45 inches
- Weight is 5,000 pounds.
600 Gallon Single Septic Tank
Specifications:
- Overall height is 62 inches
- Overall length is 79 inches
- Overall width is 48 inches
- Height to center line of inlet is 52 inches
- Height to center line of outflow is 49 inches
- Weight is 5,000 pounds.
1000 Gallon Single Septic Tank
Septic tank with a single compartment made of steel reinforced concrete (SRC). Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 96 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 8,000 pounds.
1250 Gallon Single Septic Tank
A one-compartment steel-reinforced concrete septic tank with the lower portion cast as a single piece so that there are no seams that come into touch with effluent. Specifications:
- Overall height is 60 inches
- Overall length is 117 inches
- Overall width is 68 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 10,400 pounds.
1500 Gallon Single Septic Tank
Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 11,700 pounds.
25003500Gallon Single Septic Holding Tanks
Single Septic Holding Tank with a capacity of 2500 gallonsSpecifications:
- Overall height is 68 inches
- Overall length is 144 inches
- Overall width is 78 inches
- Height to center line of intake is 61 inches
- Height to center line of outflow is 61 inches
- Weight is 16,000 pounds.
Single Septic Holding Tank with 35 00 Gallon CapacitySpecifications:
- Overall height is 98 inches
- Overall length is 144 inches
- Overall width is 78 inches
- Height to center line of intake is 91 inches
- Height to center line of exit is 91 inches
- Weight is 20,000 pounds.
Dual Compartment Septic Tanks
Description:Two-compartment tank with solids separator between the first and second compartments, holding 500 gallons and 500 gallons, respectively. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 96 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 10,000 pounds.
1250 Gallon Dual Septic Tank
Description:Two-compartment tank with a solids separator between the first and second compartments, holding 625 gallons and 625 gallons. Specifications:
- Overall height is 60 inches
- Overall length is 117 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 10,700 pounds.
1500 Gallon Dual Septic Tank
Description:Two compartment system with a capacity of 1000 gallons in the first compartment and 500 gallons in the second compartment. The dosage pump portion is usually found in the second compartment. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 11,700 pounds.
Triple Compartment Septic Tanks
Description:Three-compartment system with a solids separator between the first and second compartments. Each compartment holds 500 gallons. The dosage pump segment is usually found in the third compartment. Lower part is cast as a single piece, with no seams that come into touch with effluent or other contaminants. Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of inlet is 52 inches
- Height to center line of exit is 49 inches
- Weight is 12,000 pounds.
Chlorine Contact Tanks
Specifications:
- Overall height is 56 inches
- Overall length is 79 inches
- Overall width is 48 inches
- Height to center line of inlet is 48 inches
- Height to center line of outflow is 45 inches
- Weight is 5,000 pounds.
Siphon Dose Tank Packages
Specifications:
- It measures 56 inches in height, 79 inches in length, 48 inches in width, 48 inches in height from center line of intake, 48 inches in height from center line of outlet, and 5,000 pounds in weight. It is equipped with an indoor alarm and alarm float.
1000 Gallon Siphon Tank Package
Specifications:
- It measures 60 inches in height, 102 inches in length, and 67 inches in width. It measures 52 inches in height from the center line of the inlet and 52 inches in height from the center line of the outlet. It weighs 10,000 pounds. It comes with an indoor alarm and an alarm float.
1250 Gallon Siphon Tank Package
Specifications:
- It measures 60 inches in height, 117 inches in length, and 68 inches in width. It measures 52 inches in height from the center line of the inlet and 52 inches in height from the center line of the outlet. It weighs 10,400 pounds. It comes with an indoor alarm and an alarm float.
1500 Gallon Siphon Tank Package
Specifications:
- Overall height is 60 inches
- Overall length is 150 inches
- Overall width is 67 inches
- Height to center line of intake is 52 inches
- Height to center line of exit is 52 inches
- Weight is 13,000 pounds
- Includes indoor alarm and alarm float
Aeration Septic – Septic Tank Risers and Lids
Septic tank lids, risers, and covers are an excellent method to save time and money while also increasing safety around the septic system and preventing flooding. Installing septic tank lids and risers to bring access to your system up to code can save you the money you would otherwise spend on having your system dug up every time it has to be pumped. If you replace heavy concrete lids with lightweight yet sturdy and durable plastic lids that can be attached securely to protect the safety of children and dogs in the vicinity of the system, you may save your back.
Polylok Septic Tank Risers and Lids
12″ x 6″ Septic Tank Riser made of Polylok
- Extra strength is provided by heavy-duty structural rib reinforcing. For UV-Rays, a green opaque hue is used. Molded warning signs that are clearly visible for safety
- Frost is prevented from clinging to frost prone locations by structural ribs on the interior.
Riser Lid for Septic Tank with Polylok 12″ Lid
- Surface that is skid resistant
- The highest level of UV protection currently available
- In order to dissuade unwanted entrance, square drive screws are used.
Septic Tank Riser Polylok 20″ x 6″ Polylok Septic Tank Riser
- Watertight and airtight
- Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction. Frost is prevented from clinging to frost-prone locations by structural ribs on the interior.
Septic Tank Riser Polylok 20″ x 12″ Polylok 20″ x 12″
- Watertight and airtight
- Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction.
Riser Lid for Septic Tank with Polylok 20″ Lid
- The surface is slip-resistant, and it has two recessed handles for simple removal. The most effective UV protection available
- In order to dissuade unwanted entrance, square drive screws are used.
The Polylok 20″ Heavy Duty Septic Tank Lid is made of polypropylene.
- Surface that is skid resistant
- The highest level of UV protection possible
- It has a foam gasket to provide an airtight and waterproof connection. In order to dissuade unwanted entrance, square drive screws are used.
The Polylok Septic Tank Riser measures 24″ x 6″.
- Watertight and airtight
- Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction. Bring the septic access up to grade in no time
The Polylok 24″ x 12″ Septic Tank Riser is made of polyethylene.
- Watertight and airtight
- Provides the highest level of UV protection currently available. High-density polyethylene is used in its construction.
Riser Lid for Septic Tank with Polylok 24″ Lid
- The surface is slip-resistant, and it has two recessed handles for simple removal. The most effective UV protection available
- In order to dissuade unwanted entrance, square drive screws are used.
Alternatively, you may phone us at 330-236-1561.
Tuf-TIte Septic Tank Risers and Lids
Tuf-Tite 20″ x 6″ Septic Tank Riser is made of polyethylene.
- Watertight and airtight construction
- Bring the septic access up to grade in no time
- Stackable
Tuf-Tite 20″ x 12″ Septic Tank Riser is made of polyethylene.
- Watertight and airtight construction
- Bring the septic access up to grade in no time
- Stackable
Tuf-Tite Heavy Duty Septic Tank Lid, 20″ in Diameter
- Air and watertight connection made possible by a foam gasket
- Heavy-duty, long-lasting structure
Tuf-Tite Septic Tank Riser (24″ x 6″ x 5″)
- Watertight and airtight construction
- Bring the septic access up to grade in no time
- Stackable
Tuf-Tite Septic Tank Riser (24″ x 12″ x 4″
- Watertight and airtight construction
- Bring the septic access up to grade in no time
- Stackable
Tuf-Tite Heavy Duty Septic Tank Lid, 24″ in Diameter
- A foam gasket is used to ensure an airtight and waterproof connection. Heavy-duty, long-lasting structure
- Screws made of stainless steel are provided.
Tuf-Tite Domed Septic Tank Lid, 24″ in Diameter
- Screws made of stainless steel are supplied
- Two horizontal safety screws are also included.
How septic tank lids and covers are saving you money – Aeration Septic
A septic tank system may be one of the most expensive mechanical elements on a property, making it one of the most important investments. It is also one of the least thought about or comprehended of all the concepts. It may be tempting to flush it down the toilet and forget about it, but doing so may be quite costly in the long run, since regular maintenance and monitoring can help to avoid pricey repair fees. Risers and lids for septic tanks are an excellent and cost-effective solution to ease future maintenance and monitoring of the tank.
What are septic tank risers and lids?
While your septic tank is located beneath the earth, septic tank risers provide a big diameter “well” that allows for a safe access point to the sewage tank to be located at ground level if necessary. The lid is attached to the top of the riser and is designed to completely encapsulate the system in an airtight and watertight manner. In this way, surface water and debris such as grass clippings, mulch, and soil are prevented from entering the tank. It also helps to keep gases and smells from leaking from the septic system as well.
There are several benefits to septic tank risers and lids
First and foremost, having a clearly visible septic tank lid on the property serves as a pleasant reminder that a septic system is in place. However, whereas older-style concrete coverings were considered to be heavy and unattractive, current plastic lids are lightweight and made to integrate with the surrounding environment. These lightweight variants make it simple and cost effective to install, monitor, and service your septic system, and they are also easy to transport. Savings on expenses By establishing an access point at ground level, service experts will have an easier time locating the septic system for routine maintenance, repairs, or to pump out the septic tank as necessary.
Stainless steel threaded fasteners are used to connect lids to the riser and keep them in place to avoid tampering by minors and potential falls into the septic tank.
The high duty riser and lid systems placed at ground level are sturdy enough to withstand being mowed directly over.
As a result, there is no need to spend the additional time and energy trimming around them.
At Aeration Septic Inc, we provide several different types and sizes of septic tank covers and lids. More information may be found by checking out our collection or by visiting our Amazon shop.
Septic Tanks – Graves Concrete
The items offered by Septic Supplies include Presby Environmental and Infiltrator Systems, Polylok FiltersRisers, Zabel Filters, Tuf-Tite FiltersRisers, SRW Fabrics, Poly Barriers, Trench Drains, PVC PipeFittings, Cast Iron FrameCovers, Liberty Pumps, Alarms, and Control Panels, among others.
View Septic Tank Delivery Charges
| Monolithic Tanks H10 | Cover | Price | |
| 500 | H10PDF | H10 Cover | $770.00 |
| 500 | H10 | H10 Cover with plastic risercover | $773.00 |
| 500 | H10 | 8″ Cover | $825.00 |
| 1000 | H10PDF | H10Cover | $836.00 |
| 1000 | H10 | H10 Cover with plastic risercover | $884.00 |
| 1000 | H10 | 8″ Cover | $913.00 |
| 1500 | H10PDF | H10 Cover | $935.00 |
| 1500 | H10 | H10 Cover with plastic riserscovers | $1079.00 |
| 1500 | H10 | 8″ Heavy Cover | $1045.00 |
| 1000/500 | H10PDF | H10 4″ Cover | $1034.00 |
| 1000/500 | H10 | H10 Cover with plastic riserscovers | $1178.00 |
| 1000/500 | H10 | 8″ Heavy Cover | $1144.00 |
2 Piece Tank
| 2000 | H10PDF | 4″ Cover | $1,870.00 | |
| 1386 / 693 | H10PDF | 2/3 – 1/3 | 4″ Cover | $2090.00 |
| 1386 / 693 | H20 | 2/3 – 1/3 | 4″ Cover | $3113.00 |
| 1500/500 | H10PDF | 4″ Cover | $1996.00 | |
| 2000 | H20PDF | 6″ Cover | $2904.00 | |
| 1500/500 | H20PDF | 6″ Cover | $3025.00 | |
| 3000 | H10PDF | 3 pc. | 6″ Cover | $3410.00 |
| 3000 | H20PDF | 3 pc. | 6″ Cover | $4320.00 |
Distribution Box
| 5 Outlet | H10 | $65.00 |
| 5 Outlet | H20 | $80.00 |
| 6 Outlet | H20 | $140.00 |
| 7 Outlet | H10 | $80.00 |
| 7 Outlet | H20 | $100.00 |
| 10 Outlet | H10 | $190.00 |
| 13 Outlet | H10 | $300.00 |
Riser
| 5 Outlet | H10 | $50.00 |
| 5 Outlet | H20 | $60.00 |
| 7 Outlet | H10 | $60.00 |
| 7 Outlet | H20 | $70.00 |
| 10 Outlet | H10 | $117.00 |
