What Is The Proper Way To Install A Septic Tank And Plumbing?

hunker.com

  • Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.

How deep should septic pipes be?

A standard leach line is considered to be three (3) feet wide and three (3) feet deep with a length as required.

How far should a septic tank be from a house?

Most importantly, a septic tank must be at least seven metres from a house, defined as a ‘habitable property’. Septic tanks are built underground and release wastewater slowly into the surrounding environment. For this reason, they must be a set distance away from a home.

Can you have a septic tank without a leach field?

The waste from most septic tanks flows to a soakaway system or a drainage field. If your septic tank doesn’t have a drainage field or soakaway system, the waste water will instead flow through a sealed pipe and empty straight into a ditch or a local water course.

What size pipe goes into septic tank?

Four-inch pipe is standard, and it should extend far enough under the house to connect with the main soil stack, which is a 3-inch pipe that extends vertically past the main bathroom and through the roof.

How deep is the septic tank outlet pipe?

After the solids settle out, effluent leaves the septic tank through the outlet pipe and flows to the drain field. The outlet pipe should be approximately 3 inches below the inlet pipe.

How far below the surface is a septic tank?

Septic tanks are typically rectangular in shape and measure approximately 5 feet by 8 feet. In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground.

Why the inlet pipe in the septic tank is higher than the outlet pipe?

Level the septic tank: The septic tank inlet tee is designed to be higher than the septic tank outlet tee. This helps assure that incoming sewage clears the baffle and enters the tank correctly, while outgoing effluent does not carry along floating solids, scum, or grease (which would clog the drainfield).

What is the fall on a 4 inch sewer pipe?

For 4-inch PVC piping and a building sewer less than 50 feet long, the minimum slope is 1 inch in 8 feet, or 1/8-inch per foot, and the maximum is 1/4-inch per foot. For sewers longer than 50 feet, the slope should be 1/4-inch per foot.

Why do I smell my septic tank when it rains?

Raining often causes atmospheric pressure changes, which can lead to the air becoming heavy. As such, the methane gases typically found in the septic tank don’t flow through the vent as they normally would. Instead, they stay low to the ground, causing a foul smell similar to rotten eggs.

Can I build a deck over my septic tank?

You should never build a deck over a septic field; doing so will prevent the natural draining and dissipation of the effluent. This can ruin the septic system, not to mention releasing foul smells into the air all around your deck. The dissipating effluent can also rot the deck from underneath.

Is planning permission required for septic tank?

The short answer is yes. You will need planning permission from a local authority in order to have a septic tank installed, no matter if it’s at your own home or on a business site.

What can I use instead of a septic tank?

Alternative Septic Systems

  • Raised Bed (Mound) Septic Tank Systems. A raised bed drain field (sometimes called a mound) is just like what it sounds.
  • Aerobic Treatment Systems (ATS) Aerobic systems are basically a small scale sewage treatment system.
  • Waterless Systems.

What is the difference between a septic tank and a leach field?

The septic tank stores solid waste products that are not reduced to liquid effluent until you have them pumped out and disposed of properly. The leech field is a series of perforated pipes that provide an effective means for disposing of contaminates without endangering animals or contaminating the ground water.

What is the alternative to a septic tank?

Mound systems work well as alternatives to septic tanks when the soil around your home or building is too dense or too shallow or when the water table is too high. Although they are more expensive and require more maintenance than conventional systems, mound systems are a common alternative.

How to Install a Septic System

Documentation Download Documentation Download Documentation In rural regions of the nation where waste water treatment is not accessible, private on-site wastewater treatment systems (POWTS), also known as septic systems, are utilized largely to treat waste water. Gravity fed/conventional systems are divided into two broad categories: 1. gravity fed/conventional systems and 2. alternative (pump) systems, which include aerobic treatment units (ATUs.) In most cases, electric pumps are used in alternative systems.

However, in many health jurisdictions across the United States, it is still feasible for an individual property owner with heavy equipment operation skills to utilize a backhoe to establish a septic system on their land.

Steps

  1. 1 Make a plan and design for your system. Performing a site survey and conducting a percolation (soil) test on the area where the POWTS is to be placed are both required initial steps in any septic system installation. In order to create a system, it is necessary to first gather information from surveyors and conduct a soil test. It is then possible to submit an application for the necessary permissions and approvals.
  • The following are some of the conclusions from the site survey that have an impact on the design:
  • Available space
  • Terrain
  • Intended purpose and projected water demand depending on the size of the residence or building that the system will serve
  • Location of the well and/or nearby wells
  • And other factors.
  • The following are examples of soil test findings that have an impact on the design:
  • The soil type and layering (sand, clay, rock, and where it is placed in relation to depth)
  • The soil’s ability to drain and filter wastewater
  • And the soil’s ability to drain and filter wastewater
  1. 2Wait for clearance before proceeding. The system may be deployed once all of the relevant permissions and approvals have been obtained. Make certain that all of the steps listed below are carried out in accordance with all applicable laws, plumbing rules, and building codes. Advertisement

Please keep in mind that the following procedure assumes that the system is being installed for the first time and not as a replacement.

  1. 1 Assemble the equipment and tools that will be used throughout the dig. You will require the following items:
  • First, gather all of your excavation-related equipment and tools into one place. To complete this task, you will require the following materials:
  • 2 Determine the location of the entrance to the building in relation to the location of the septic tank. Make an excavation at least 2 feet deep and drill a hole through the wall, or go deeper and drill a hole beneath the footing, depending on your preference or the need. Because this is precisely what a gravity-fed system is designed to accomplish, expect the flow to continue to flow downhill from here. When transferring waste from the tank to the drain field, it does not employ any mechanical methods other than gravity.
  • The pipe should be 4″ Sch. 40 and should extend at least five feet outside the structure toward the tank, either through the wall or beneath it. Set it level where it will pass through a wall or under a footing, and from there, run it with approximately 1/8″ of pitch (slope) every foot of length toward the septic tank until it reaches the tank. If necessary, go even farther into the tank or all the way into the tank. If this is the case, switch to 4″ 3034 with the appropriate adaptor and pipe 3034 toward the tank.
  • Make sure you use a test cap on the end that will be entering the building. It is recommended that if you are going through a wall, you seal the area around the hole with hydraulic cement both inside and outside
  • Do not run too much pitch out to the tank. If there is an excessive amount, the water will run away quicker than the sediments, resulting in the solids remaining in the pipe. Additionally, depending on the depth of your drain field and how close it will be to the tank’s outflow, there may not be enough pitch to get to the drain field.
  • 3 Dig a hole large enough to accommodate the installation of the concrete aerobic tank below ground. Make use of the laser transit to “shoot” the top of the pipe that leads out to the tank with the laser. The distance between the top of the intake and the bottom of the tank is measured in feet and inches. To the number you fired off the top of the pipe, add this (go up on the grade pole) + 1 1/2″ to get the total. The depth of the grade pole has now been adjusted to the desired depth. Using this, continue to drill the hole to the desired depth
  • Prepare your leech field by laying it out and excavating it according to the results of the test performed during the permit application procedure. Maintaining a good flow between the tank and the drain field should be considered when planning out and digging the tank.
  1. Using the results of the leech field test conducted as part of the permit application procedure, lay out and dig your leech field. Maintaining a good flow between the tank and the drain field should be considered when planning out and digging.
  1. A pump chamber after the septic tank should be installed The pump chamber, also known as a pressure tank or dosing tank, is where the electric pump is housed, which is responsible for transporting wastewater from one location to another and finally into the drain field for final disposal.
  • Set up the pump chamber in the same manner as you would a septic tank. The effluent pump and floats are housed in the pump chamber, and they are responsible for pumping the effluent out to the drain field at predetermined or scheduled intervals. This is a hermetically sealed system. To ensure that the electrical installation complies with state standards, it is frequently necessary to hire a qualified electrician. It is important to remember that in places with high groundwater, the pump chamber or additional ATUs may remain essentially empty for long periods of time, and that these tanks may need to be safeguarded from floating by the installation of additional weight or other protective features.
  1. Secondly, all construction details, including the layout of all sewers outside of the home, the location and depth of all tanks, the routing and depth of pressurized effluent lines, and other system components, such as the drain field and any additional ATUs, must be consistent with the septic system plans approved by the local county health department. Cover the tank and pressurized lines once the inspector has given his final clearance and the system has been turned on. Advertisement

Create a new question

  • Question I had a tank put, but it isn’t level with the ground. What will be the ramifications of this, and should it be leveled? It is necessary to keep the tank level. It is difficult to predict what it will have an impact on because we do not know which direction it is off level. Question Is it necessary to be concerned about tree roots growing into the drainage area when using a gravity flow kind of tank? Whether or whether you have lateral lines is dependent on the kind of trees that are growing close or above them. Tree species that tend to extend roots into the lateral lines and obstruct them are known as ramifications. Due to the fact that they are buried deep in the ground and surrounded by a pocket of gravel that allows waste water to drain out, they are rarely affected by grass, weeds, and shrubs. Question What is the maximum depth that a pipe may be lowered into the leech bed? The majority of systems require 12 volts “in the form of rock The perforated pipe should be suspended in the top area of the rock
  • It should not be touching the rock. Question Maintaining a lush green grass on or above your pitch is it safe, or is it a good practice? According to what I’ve heard, brown or dead grass is preferred so that your field can breathe more easily. It is necessary for your field to take a breath. The presence of green grass across your field indicates that it is functioning well. With lush grass covering your field, it will be able to breathe. There should be no planting of woody shrubs or trees over the leach field. Question What is the recommended distance between the septic tank and the house/boundary? A minimum of fifty feet is required. States have different laws, but this is the most common distance
  • Nonetheless, other states have stricter laws. Question What is the average amount of soil that goes into a residential leach field? It is dependent on how chilly it becomes. There are no less than 12 in the northern United States “in the leach field’s surface
  • Question Is it possible to build a septic system during the cold months? What you should do will depend on whether or not you reside in a place where the ground freezes. Question What amount of water should I put in the tank to get it going? None. A typical tank holds 1,000 gallons and will fill up quite quickly if used on a regular basis. When liquid effluent is discharged to the drain field, the goal is to catch and pre-treat particles that have accumulated. It is possible that a pump system will require water to prime the pump. Question There is a misalignment between my septic field’s underground line and the pipe on the tank. Is it OK to utilize a 90-degree elbow on my septic tank? As long as you have decent downhill flow, you should be fine. Instead of using a 90, I would use two 45s. Question If I’m installing a septic system, when should I contact an inspector? Immediately following system installation but before earth is used to cover the system in place Always check with the inspector ahead of time to verify that they can satisfy your inspection needs
See also:  How To Fix A Backflowing Septic Tank? (Perfect answer)

More information on the replies Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

  • The use of aerobic bacterial additions (which are available at most DIY stores) to maintain a healthy and well functioning system, as suggested by producers on a periodic basis, is contentious. The septic tank is an anaerobic (wet) environment in which the majority of yeasts and other additions will have little or no effect on the sewage being processed. When it comes to installing septic tanks, some old school installers believe that placing an additive, a shovel of muck, or even a dead cat in an empty tank will “start” the process. What naturally enters the tank serves as the only thing that is necessary. The aerobic (wet or dry) component of the system consists of hundreds of square feet of drain field, where additives will do little help even if they make it all the way to the end of the system. The use of chemicals in septic systems has not been the subject of an independent research that has been published in a respectable scientific publication anywhere in the world, including this nation. This will mostly certainly be confirmed by your local health department. Each phase of the building process will almost certainly include an examination by a health inspector before the work can be completed or covered up. On pressurized lines, the use of a sand embedment is recommended in order to reduce the amount of damage caused by moving soil that has a high concentration of clay. When pumps are turned on and off, pressurized lines might move as well. Four inches (10.2 cm) of sand bedding on all four sides of the lines will prevent sharp pebbles from the ground or backfill from wearing holes in the pipe over time
  • And

Thank you for submitting a suggestion for consideration! Advertisement

  • Keep the perforated pipe for the leech field in a vertical position while installing it to avoid having the holes in the pipe turn downward. It is necessary to lay the perforated drain field pipe ASTM 2729 dead level, so that the printed line on the pipe is facing up. The perforations on both sides of the pipe are on both sides of the pipe. All of the sections of perforated pipe are cemented together, and the ends of each leach line are capped to complete the installation. So, when waste water enters the pipe, it will fill the pipe to the height of the perforations and overflow from ALL of the holes, utilising the whole leach field as a means of treatment. In certain health authorities, you can utilize waste water to water grass or decorative plants, trees, vegetable gardens, and fruit trees if you place the perforated pipe on a slope. However, the water must first be cleaned by the system (tertiary treatment includes disinfection) in order to prevent pathogens (germs) from the septic system from being discharged into the environment throughout the process. Make sure to check with your local health authority to verify if the practice known as “reuse” is permitted in your community.

Advertisement

Things You’ll Need

  • The following tools are required: backhoe tractor, trencher, shovel, contractor’s laser level and rod, or a surveyor’s transit. Septic tanks
  • PVC pipe with perforations
  • Material for embedding
  • PVC adhesive, PVC fittings, and a septic tank outlet filter are all included. Hand saw
  • Course file
  • Sandpaper If necessary, effluent pumps and floats are installed. If an alternate system is used, a control panel is installed.

About This Article

The writers of this page have together authored a page that has been read 498,372 times.

Did this article help you?

To process and dispose of waste, a septic system has an underground septic tank constructed of plastic, concrete, fiberglass, or other material that is located beneath the earth. Designed to provide a customized wastewater treatment solution for business and residential locations, this system may be installed anywhere. Although it is possible to construct a septic tank on your own, we recommend that you hire a professional to do it owing to the amount of skill and specific equipment required.

Who Needs a Septic Tank?

For the most part, in densely populated areas of the nation, a home’s plumbing system is directly connected to the municipal sewer system. Because municipal sewer lines are not readily available in more rural regions, sewage must be treated in a septic tank. If you’re moving into a newly constructed house or onto land that doesn’t already have a septic tank, you’ll be responsible for putting in a septic system on your own.

How to Prepare for Your Septic Tank Installation

Here are a few pointers to keep in mind to make sure your septic tank installation goes as smoothly as possible.

Receive Multiple Estimates

Receiving quotations from licensed septic tank installers and reading reviews about each firm using trustworthy, third-party customer evaluations should be done before any excavation or signing of any paperwork is done.

Examine your options for a contractor and make sure they have the appropriate insurance and license, as well as the ability to include critical preparations such as excavation and drain field testing in their quotation.

Test the Soil and Obtain a Permit

For septic systems to function properly, permeable soil surrounding the tank must absorb and naturally handle liquid waste, ensuring that it does not pollute runoff water or seep into the groundwater. The drain or leach field is the name given to this region. Before establishing a septic tank, you are required by law to do a percolation test, sometimes known as a “perc” test. This test indicates that the soil fits the specifications established by the city and the local health agency. In most cases, suitable levels of permeable materials, such as sand or gravel, are necessary in a soil’s composition.

Note: If you wish to install a septic tank on your property, you must first ensure that the ground passes the percolation test.

Plan for Excavation

Excavation of the vast quantity of land required for a septic tank necessitates the use of heavy machinery. If you are presently residing on the property, be careful to account for landscaping fees to repair any damage that may have occurred during the excavation process. Plan the excavation for your new home at a period when it will have the least influence on the construction process if you are constructing a new home. Typically, this occurs before to the paving of roads and walkways, but after the basic structure of the home has been constructed and erected.

The Cost of Installing a Septic Tank

There are a few installation charges and additional expenditures connected with constructing a new septic system, ranging from a percolation test to emptying the septic tank and everything in between.

Percolation Test

A percolation test can range in price from $250 to $1,000, depending on the area of the property and the soil characteristics that are being tested. Ordinarily, specialists will only excavate a small number of holes in the intended leach field region; however, if a land study is required to identify where to excavate, the cost of your test may rise.

Building Permit Application

A permit will be required if you want to install a septic tank on your property. State-by-state variations in permit prices exist, however they are normally priced around $200 and must be renewed every few years on average.

Excavation and Installation

When you have passed a percolation test and obtained a building permit, your septic tank is ready to be professionally placed. The cost of a new septic system is determined by the size of your home, the kind of system you choose, and the material used in your septic tank. The following is a list of the many treatment methods and storage tanks that are now available, as well as the normal pricing associated with each.

Types of Septic Tank Systems

Septic system that is used in the traditional sense Traditionally, a septic system relies on gravity to transport waste from the home into the septic tank. Solid trash settles at the bottom of the sewage treatment plant, while liquid sewage rises to the top. Whenever the amount of liquid sewage increases over the outflow pipe, the liquid waste is discharged into the drain field, where it continues to disintegrate. This type of traditional septic system is generally the most economical, with an average cost of roughly $3,000 on the market today.

Drain fields for alternative systems require less land than conventional systems and discharge cleaner effluent.

Septic system that has been engineered A poorly developed soil or a property placed on an uphill slope need the installation of an engineered septic system, which is the most difficult to install.

It is necessary to pump the liquid waste onto a leach field, rather than depending on gravity to drain it, in order to ensure that it is equally dispersed across the land. The average cost of these systems is roughly $8,000.

Types of Septic Tanks

  • Concrete septic tanks are long-lasting and rust-proof, but they are difficult to repair if they are damaged. It is possible that concrete tanks will cost up to $2,000 depending on their size. Plastic —While plastic tanks are cost-effective, they are also susceptible to damage. They are around $1,200 in price. Fiberglass —While fiberglass septic tanks are more durable than their plastic counterparts, they are susceptible to shifting or displacement if the water table rises to an excessive level. Depending on the model, these tanks may cost up to $2,000

More information may be found at: Septic Warranty Coverage and Costs.

Using Your Septic Tank

It is important to maintain the area around your new septic tank’s drain field and to frequently check your tank using the lids included with it. Never use a trash disposal in conjunction with your septic tank since it might cause the system to clog. Additionally, avoid driving over the land where your septic tank is located or putting heavy gear on top of your septic tank or drain field to prevent damage. Most of the time, after five years of septic system use, you’ll need to arrange a cleaning and pumping of the system.

Send an email to our Reviews Team [email protected] if you have any comments or questions regarding this post.

How to Install a Septic Tank and Field Line Sewer System

The installation of a septic tank is not a do-it-yourself project. Image courtesy of Kwangmoozaa/iStock/Getty Images. You shouldn’t try to install a septic system yourself unless you are a heavy equipment operator or a professional. Even if you have heavy machinery at your disposal and are familiar with how to operate it, you will still require a significant amount of professional assistance. There are several professionals you’ll need: a soil expert to assess the site, an engineer to design an appropriate system, a plumbing contractor to install and connect pipes, and possibly an electrician to assist with the installation of any pumps or timers that may be required.

Septic System Design Variations

A total of nine different types of septic systems are listed by the United States Environmental Protection Agency, and that doesn’t even include systems that are not gravity-fed and instead rely on a transfer pump. Septic tanks and a drain field sunk into the earth are the components of the traditional septic system. This is the system that most people envision, but it is only one of several options, and it is not necessarily the best one. It is possible that local health authorities will require an additional system, depending on the soil quality, topography, drainage conditions, anticipated usage, and other factors; in this case, it is necessary to hire an engineer who will work with the health authorities to design and obtain the necessary permits.

Installation Isn’t a Straight Shot

The designs are in hand, but it is not always a straight line from there to the actual installation for the homeowner who is working with an engineering firm. Mr. Rooter, in fact, gives the following advise to homeowners who are considering installing their own septic components: Don’t. Just too many things may go wrong with a system, leading to poor drainage, inadequate plumbing in the house, or pollution of the local water table, to mention. For those who are inclined to do it themselves, or for whom the circumstances demand that they do it themselves, and who have access to an excavator and crane, the installation of a standard system is quite straightforward to comprehend and execute.

To make the installation legally compliant, keep in mind that you’ll need to have every stage of the system evaluated before you backfill the hole.

Installing a Conventional Septic System

A traditional septic installation begins with the excavation of a hole for the tank in accordance with the placement specifications provided on your approved plan. After putting the tank into the hole, you link it to the building sewer using 3- or 4-inch waste pipe, which must maintain a minimum slope toward the tank, and you run a drain pipe from the other end of the tank to a distribution box positioned in the drain field, as shown in the diagram. After that, you’ll need to dig a series of parallel trenches that will reach from this box all the way across the drain field.

  1. Connect the pipes to the distribution box and cover the pipes with a sheet of plywood.
  2. In order for a gravity-fed septic system to function properly, the building and drain field must be on a consistent downhill slope.
  3. An alarm system that warns you if a fault occurs must be linked to the pump in addition to the power source.
  4. For this reason, having the pump installed by a professional electrician who can guarantee the job is highly advised.
See also:  What Are The Demensions Of A 1000 Gal. Septic Tank? (Correct answer)

How to Run a Septic Tank Line From Your House

A septic system is made up of two lengths of pipe that are connected together. Initially, it runs from the house, where the system services are located, to a tank, where the waste is separated and solids settle out. The second section runs from the tank to the drainage field, where fluids from the tank are dispersed into the earth underneath the tank. The process of installing the first run of pipe is quite similar to that of installing a traditional sewage line. It is necessary to maintain a downhill slope to the storage tank.

Locating the Septic Tank

The tank serves as the nerve center of the septic system. It is required to be situated between the residence and the drainage field. Each and every septic installation must begin with a soil test, and depending on the results, soil conditions may necessitate the placement of the tank in a less-than-ideal site for digging sewer lines. Also required are minimum setback distances from property borders, functioning wells, surface water and other obstructions to provide a safe working environment.

Tank Depth

A standard septic tank has a 4-inch intake at the top, which is positioned towards the bottom. Ideally, a 1/4-inch-per-foot slope toward the pipe from the house should be maintained by the pipe connecting to it. To put it another way, for every 10 feet of distance between a tank and a home, the inlet must be 2 1/2 inches lower than where the pipe departs the house at its lowest point.

The pipe usually exits at ground level, although it may need to pass beneath a foundation footing or concrete pad in rare cases. Because the pipe can never be reversed in its slope, the depth of the footing or pad at the bottom defines the depth of the tank below the surface.

Digging the Trench

The trench for the septic pipe should be dug before the hole for the tank since you will need a backhoe to complete the work and the tank will get in your way if it is already in the ground. To allow rainfall to drain properly, the pipe should be placed on a 2- or 3-inch bed of drain rock, so remember to account for this extra depth when digging. It is normal to use a four-inch pipe, and it should be installed far enough down to link with the main soil stack, which is a three-inch pipe that runs vertically past the main bathroom and through the roof of the home.

Precautions

Since you’ll need a backhoe for the task and the tank will get in the way of your work if it’s already in the ground, it’s usually best to build the trench for the septic line before digging a hole for it. Take into consideration that the pipe should be placed on a 2- or 3-inch layer of drain rock in order to allow rainfall to drain properly. It is typical to use a four-inch pipe, and it should be installed far enough underground to link with the main soil stack, which is a three-inch pipe that runs vertically past the main bathroom and through the roof of your home.

Greenville Septic Tank Repair

Unsanitary and unhealthy living conditions are made impossible without a properly installed and well-maintained septic tank. When your septic tank needs to be repaired or replaced, call the trained and experienced plumbers at Duckett Plumbing for a free consultation. For more than 50 years, we have been providing septic tank repair and installation in Greenville and Anderson, South Carolina. If you need septic tank repair or installation, contact (864) 664-2221 and one of our professional plumbers will be there to assist you.

Common Septic Tank Problems

Despite the fact that the septic tank is buried in the earth, there are several symptoms that indicate that there may be an issue with it. A septic system malfunction might be the cause of wastewater backing up into your home, a sewage stench in the yard or from the drains, sluggish drains within the house, gurgling sounds from the drains, or water collecting in the yard. If you observe any of these symptoms, call your local septic service provider. We can assist you with frequent difficulties that are caused by:

  • Wastewater backing up into the home because to clogs or leaks
  • The residence is creating more wastewater than the system is capable of dealing with. Infiltration of tree roots
  • The use of heavy machinery over the septic system can cause significant damage. System design or implementation that is substandard
  • The absence of upkeep

Any of the symptoms listed above indicate that you should contact an experienced septic tank repair technician as soon as possible. Quickly identifying the cause of the problem and obtaining expert assistance will help you prevent a more serious problem with your septic system and potential damage to your house.

Septic Tank Installation and Repair

Whether you want a new tank or a repair, we can provide Greenville septic tank repair and installation with service that is tailored to your specific requirements. If it is necessary to install a new septic tank, it is critical that the tank be the proper size. We can assist you in determining the tank size that is required to satisfy the unique needs of your house in order to ensure that the system will fulfill the demand. Problems with septic systems may frequently be resolved by a plumbing contractor who has had adequate training and experience.

We provide transparent pricing and written quotes for septic tank repair, which means you will only be responsible for the fee that we quote before we begin the service. You may be eligible for a refund of our in-person assessment cost if we complete your septic tank repair or installation.

Should You Repair or Replace Your Septic Tank System

Often, a simple repair is all that is required to keep your septic system up and operating smoothly. That being said, if you have an older system or one that is continuously in need of maintenance, you might think about having a new septic tank installed. Septic tanks have a lifespan of around 40 years, so if you are building a new house, you may want to consider replacing your system.

Maintaining Your Septic Tank

The majority of the time, a simple repair will suffice to keep your septic system operating effectively. In light of the foregoing, if you have an older system or one that is continuously in need of maintenance, you might think about installing a new septic tank. It is possible that your septic tank system may need to be replaced if you move into a new house after 40 years.

  • Inspections to check for damage, broken pipes, and other concerns on a regular basis
  • The manual removal of extraneous items from within the tank
  • And There will be no need of harsh synthetic chemicals to clean the tank. Avoiding the use of foreign materials such as coffee grounds, diapers, cigarettes, and other such items

The best course of action if a problem emerges with your septic tank is to leave the repair to a professional who has the necessary expertise and understanding. Septic plumbing problems can be resolved the same day if they occur. In addition, we provide emergency plumbing and septic service for customers who are experiencing a plumbing or septic issue. You should contact (864) 664-2221 to schedule an examination if you have any reason to believe your septic tank is failing.

Septic Tank Installation Steps

Septic tank installation is a complex and time-consuming procedure that demands both expertise and patience. Our track record of providing high-quality septic tank installation and septic tank repair is something we are very proud of here at Septic Connection. Education is a critical component of our customer interaction strategy. The property owner, as the customer, should be aware of and understand the method in order to guarantee that the suitable system is put on their property. The septic system is essential for the proper regulation of plumbing and sewage flow.

  • Knowing what to expect throughout the installation process offers the client the ability to monitor and evaluate the work of the septic provider.
  • 1.Conducting research into the most appropriate septic system All property owners are highly recommended to perform extensive study before making a decision on which septic system to install.
  • Some of the things to take into consideration include the estimated production of wastewater, current municipal and federal rules, and other customer preferences, such as the availability of recycling services.
  • Our expertise will provide you with the direction and assistance you require to take off.
  • Before submitting your application, ensure that you have gathered all of the necessary documentation to enable for expedited processing and an appeal in the event of a refusal.
  • Some municipal or state rules will have a significant impact on the type of system you install, so it is important to contact with the septic firm and local officials before beginning the installation.
  • 3.Inspection of the property and installation of plumbing Surveying is essential since it will produce the data that will be used to develop the project plan.
  • The location chosen should be conveniently accessible in order to make the installation procedure and future septic tank maintenance as simple as possible.
  • Technicians from our septic firm, Septic Connection, will complete the plumbing to the best standards possible, preventing costly leaks and repairs in the future.
  • In compliance with applicable rules and regulations, this should be carried out.
  • To keep expenses down and prevent congestion, it should ideally rely on gravity to function.

Although it is not always essential, depending on the geography and other adjustments, it is occasionally necessary to have a pump in place to force the wastewater against gravity. We will evaluate the septic system before passing it over to the new owners so that we can make any required repairs.

Are You Planning to Install a Septic System?

Are you looking for a septic service provider? Please contact us immediately. Septic Connection is a well-established and properly licensed septic service company. We have put together a group of qualified specialists that will make the entire procedure simple and pleasurable for you by assisting you at every step of the process. Because we also provide septic tank repair services, we anticipate a long-term relationship. We make every effort to provide high-quality services on schedule. Contact us immediately to set up a meeting so that we can get started.

How to Build a DIY Septic Tank System

You may install a septic tank system yourself to save money on the costs of hiring a professional septic designer and digger, which can add up quickly. Even if you design your own DIY septic tank and drainage system from scratch, the cost of installing a new septic system is high. Although it is possible to save money by establishing your own septic tank system, it is not recommended.

Costs of a DIY Septic System

The connection of a waste disposal system to a septic tank is critical for the health and cleanliness of the community. The installation of a septic system will be required if your property is located in an area where there is already no underground sewerage system. The public health fees for permits to construct a septic tank system are determined mostly by the county in which you live, but you will almost certainly be unable to avoid paying the permit charge. In order to establish the retail prices of yourDIY septic system design, which includes the drain field, distribution box, and pipes, you must first determine the price of the building supplies.

When shopping for hardware and home improvement supplies, compare prices amongst different establishments.

On top of that, you’ll have to consider about the excavation as well.

Before You Start Digging

Before you begin the actual building work, it is generally a good idea to do a thorough assessment of the situation. A scale map of your home and property would be a good idea before you get your shovel out and start digging holes. The best location for a residential septic system is the backyard, underneath the garage, or any side of the house that is adjacent to a street. Choosing the location before you start digging the hole for your septic system is an important step in the process.Selecting the location before you start digging the hole for your septic system is an important step in the process.

When installing a tank, it is vital that it is done right the first time.

The Site Evaluation

In most jurisdictions, the old perc test has been replaced by a site evaluation as a means of demonstrating to your local health authority the treatment characteristics of your property’s infrastructure.

DIY Perc Testing

In most jurisdictions, the old perc test has been replaced by a site evaluation as a means of demonstrating to your local health authority the therapeutic characteristics of your property’s treatment facility.

Soil Classification

In most jurisdictions, the classic perc test has been replaced by a site evaluation as a means of demonstrating to your local health agency the treatment capabilities of your property.

Drainfield Trench Size

This does not affect the size of the drainfield, which is independent of the number of bathrooms or fixtures on the property. Almost all health departments employ the following methods to determine the flow rate:

  • An individual’s residence’s total number of bedrooms The amount of persons that are present in the residence
  • Water use on a daily basis
See also:  How Long Should A Septic Tank Drainage Field Be? (Solved)

The volume of sewage that must be discharged into the drainfield is determined by the flow rate. Once you have determined the kind of soil under your prospective drainfield, use the table shown here to calculate the drainfield area necessary for your house size, and you will have the drainfield size you require.

Size of The Septic Tank

The size of a septic tank construction is decided by the number of people living in the home or on the land for which it is being built. Consult the metric standards for the area in which the construction is to take place before proceeding. This is the most accurate method of determining the amount of septic tank you should use when constructing your own septic tank system. The size of your DIY septic system will also decide how frequently you will need to have your DIY septic system pumped by a professional septic pumping service, which will be determined by the size of your septic system.

Creating the Drawings

Before we can begin construction on our septic system, we must first develop the necessary designs to fulfill the requirements of your local health authority. Your DIY septic system designs may need to be more detailed than you think they need be, depending on your state’s requirements. All structures, pathways, property borders, retaining walls, and the position of the original test holes, on the other hand, must be clearly depicted.

Drainfield Layout

Your drainfield plan will necessitate the construction of a minimum of two ditches of similar size. The division of the water flow into two, three, or more lines is performed by using a distribution box, also known as a D-box, to split the flow. It is used in the distribution box to distribute water through pipes that include flow control valves in the form of eccentric plugs that distribute the water evenly across several drain lines. The effluent must travel downhill from the tank outlet, past the distribution box, and down the individual trenches before being disposed of.

Apply for a Building Permit

Now that you have the drawing, you should submit your ideas to the local health department’s office for consideration.

You will be required to complete an application form as well as pay the applicable permission cost. Following that, you will need to wait for the designs to be examined and authorized by the board of directors before moving on to the final construction phase of the project.

Building a Septic Tank System

To begin the construction process, the first step is to sketch up a rough schematic of the septic system. You’ll utilize this layout to put your construction designs into action on the ground. It is necessary to project the layout and position of all of the different components of the septic design onto the site.

Excavation of the Septic Tank System

When it comes to digging the site in order to prepare for the construction of the septic tank and drain lines, it is important to pay close attention to elevation in order to get the best possible results. The health inspector will need to inspect the job one more time after you have finished all of the excavation before you can begin backfilling. Once you have finished all of the excavating, you will need to schedule another appointment with him for a final inspection of the job before you can begin backfilling.

Backfilling the Septic Tank System

During the building process, all of the tanks, pipelines, and vaults should be backfilled around the perimeter. Your local authority may mandate that all tanks be subjected to vacuum testing, pressure testing, or water testing. Aside from that, an increasing number of counties are demanding leak testing of the tank these days. Consequently, the final backfilling of the concrete tanks can be delayed until after the final inspection to check for leaks has been completed. The final backfilling should not be completed until after the final health department inspection has been completed.

External References

  • How to Build a Septic Tank (mightyguide.net)
  • How to Build Septic Tank Systems (eco-nomic.com)
  • How to Build a Septic Tank System (eco-nomic.com)
  • How to Build a Septic Tank (mightyguide.net)
  • A Septic Tank: A Step-by-Step Guide (ehow.com)

Septic Tank Pumping in Atlanta, GA

At Integrated Plumbing Solutions, you can rely on us to provide cheap septic tank pumping and repair for industrial, residential, and commercial clients throughout MetroAtlanta and the surrounding areas. Transparency, honesty, and integrity underpin our work; there are no gimmicks, no games, and no avoiding the truth in our work. Since 1965, we have been offering septic services, and we promise that your septic tank will receive industry-leading treatment on a consistent basis. And with a track record of providing client satisfaction, there’s no reason to turn to anybody else for your septic tank repair requirements in Atlanta.

We promise that all pricing, including any additional charges, will be provided in advance and that all agreements will be reached BEFORE any work is undertaken.

In order to schedule septic tank pumping in the greater Atlanta region, please contact (770) 343-7370 right away!

Signs of External Septic System Problems

The drain field is frequently the source of the earliest signs of septic system difficulties (the underground wastewater disposal area your tank runs to.) The soil in your septic tank’s drain field is responsible for removing germs from the wastewater it treats. Eventually, however, the soils around the drain field might become polluted, resulting in a significant reduction in the system’s overall effectiveness. An inability to maintain proper drainage jeopardizes the effectiveness of the drainage system by enabling sediments to be driven into the drain field.

It is also possible for root penetration to cause difficulties for your septic lines, and driving over the system might cause damage if it has not been sufficiently buried underneath. If there is a problem with your septic system, you may begin to notice the following symptoms:

  • Septic Tank Drainage Issues: Constantly leaky or running toilets (as well as runny faucets) might indicate the presence of a septic tank drainage issue. Toilets that make a lot of noise, drain slowly, or have water flow issues might be signs of larger septic tank problems involving the home sewer or intake baffle tee (a component that helps limit the flow of wastewater). Issues with the Outlet Baffle Tee: Excessive waste might be escaping the outlet baffle if the septic tank is not properly maintained and cleaned. This might be a result of the baffle eroding, which would cause the system to fail gradually.

Depending on the severity of your septic problem, it may be preferable to replace your existing septic tank with a new and improved model. To find out more about our septic tank installation and replacement services, please contact us immediately.

Why Should I Get My Septic TankSystem Inspected?

If you do not get your septic tank pumped after 3-5 years, the buildup of sludge will cause the pump to wear out prematurely since more water will be required to break up the particles. This lack of upkeep might result in extremely expensive repairs down the road. While the majority of septic tanks are positioned 18 inches below ground level, septic tanks that are deeper than this level may necessitate further excavation. Particularly relevant in cases when the tank is positioned beneath a deck, driveway, piece of landscaping or concrete surface.

As a result, our plumbing technicians, as well as the majority of health officials, strongly advise homeowners to pump their septic tanks every three to five years in Atlanta and Kennesaw.

Benefits of Septic Tank Pumping

You may be able to get the following benefits by scheduling an Atlanta septic system inspection every three to five years:

  • Save money by avoiding costly repairs. Check to see that your septic system is in perfect working order
  • Getting your home ready to sell (this service is often not included in home inspections)
  • Preparing your home to sell Prevent the polluting of groundwater
  • Water backups into your home and the consequent damage from wastewater are avoided.

Our septic inspection service includes a full system uncovering when you engage Integrated Plumbing Solutions for your septic inspection needs. It consists of septic tank pumping (which removes up to 24 inches of solid waste), toilet flushing, and checking for indicators of backups in the system. We will also check to see that all mechanical components are in proper working order and that the drain fields are receiving adequate water. It is vital to treat septic tanks before they reach 50% capacity since this is when the pre-treatment procedure is at its most difficult.

If this is the case, schedule an inspection as soon as possible!

For Metro Atlanta Septic Experts, Call Integrated Plumbing Solutions

Hopefully, at this point, we have established that we are specialists in the field of septic tanks and septic systems in general. To be sure, we also provide financing alternatives through GreenSky, which ensures that you can always acquire high-quality equipment at an affordable price no matter what your budget is. We also offer free estimates, so if you have even the slightest suspicion that you have a septic tank problem, you should give us a call. And with emergency repairs available 24 hours a day, you’ll never have to worry about septic or sewage problems again.

A Step-by-Step Guide to Installing Your New Septic System

Although septic tank installation in San Francisco is not always a task that can be completed by one person without the assistance of a team of specialists, you may be curious about how the procedure is carried out. First and first, if you still have an old system, you’ll need to get rid of it. Following the excavation, you may proceed to the installation of the plumbing and drainage systems, before filling up the space and testing the system to ensure that it is in proper working order, as needed.

  • Excavation and removal of waste In the event that you’ve never had a septic tank before, you won’t have to bother about digging up the old tank in order to install the new tank.
  • Sometimes, additional excavation may be required in order for your brand-new septic tank and the pipes that will be connected to it to be properly installed and function properly.
  • Plumbing and drainage systems are being installed.
  • Plumbing and drainage pipes are required for the septic tank in order for it to accept waste from the residence while also filtering it out into the drainage field.
  • The System is being filled and examined.

This last inspection is critical because it provides the specialists with an opportunity to identify any little issues that may have gone unnoticed previously, allowing your system to get off to a good start.

Can Your Septic Tank Be Under the House?

Do you want to know if it is possible to put a septic tank below a house? The answer is a resounding nay. The following are three reasons why septic tanks should never be built beneath residential structures:

  1. Your house will smell like rotten eggs: Septic tanks are meant to collect and handle waste after it has been discharged from your residence. It is possible to have a tank full of trash beneath your home, which can result in a variety of problems, including severe smells. Septic services will be difficult to come by, as follows: Septic tanks must be examined and pumped on a regular basis by licensed plumbers. During the course of these services, your plumber will have to dig up the earth. It is necessary to excavate the foundation of the home and the land underneath it in order to reach the septic tank if it is located under the house. Your health might be jeopardized if you don’t act quickly: Despite the fact that septic tanks are durable and long-lasting systems, it is possible for them to be compromised. In the event that your system gets broken and begins to seep waste into the ground beneath your house, you and your family may find yourself unexpectedly living in a very poisonous environment. If this occurs, you should seek immediate medical attention.

How Far Away Should a Septic Tank Be from the House?

However, the minimum distance required between a house and its septic tank can vary depending on where you live. Generally speaking, septic tanks should be between 10 and 20 feet away from a residence (at least). If you are utilizing a well or if you reside near a stream, lake, road, swimming pool, or reservoir, you will need to take additional precautionary measures. If you have a well on your property, your septic tank will most likely need to be at least 50 feet away from it in order to function properly.

Call The Plumbing Experts for All Things Septic Tanks!

In general, septic tanks should be between 10 and 20 feet away from a house, depending on the location. However, the minimum distance requirements vary depending on the region (at least). If you are utilizing a well or if you live near a stream, lake, road, swimming pool, or reservoir, you will need to take additional precautions to protect yourself. It is likely that your septic tank will need to be at least 50 feet away from your well if one is present on your property.

  • Septic tank inspections, septic tank pumping, septic tank installs, septic tank repairs, and septic tank replacements are all services that are provided by our company.

The Plumbing Experts is the company to call when you want trustworthy service you can count on. Please contact us by phone at (864) 210-3127 or by email to find out more about how we can help you with your septic tank. We look forward to being of service to you!

Leave a Comment

Your email address will not be published. Required fields are marked *