Go to your basement or crawl space, and then look for the main sewer line that leads to your septic tank. Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside.
Are septic tank locations public record?
Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.
How do you find a septic tank in an old house?
Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home. Insert a thin metal probe into the ground every few feet, until you strike polyethylene, fiberglass or flat concrete.
How do I find out if my septic tank is registered?
Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.
How do you find a metal detector with a septic tank?
6 Steps to Locate a Septic Tank
- Find Your Main Sewer Drain Line. Sewage from your toilets, sinks, and showers collects into a main drain line.
- Check Permits and Public Records.
- Determine Septic Tank Material.
- Time to Dig.
- Mark the Location for Future Maintenance.
How often should a septic tank be pumped?
Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.
How far is septic tank from house?
Septic tanks are required to be at least 5 feet from the house, although most are between 10 and 25 feet away.
Are septic tanks still legal?
Septic Tanks Explained… Septic tanks cannot discharge to surface water drains, rivers, canals, ditches, streams or any other type of waterway. you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.
Does a septic tank have to be registered?
A septic tank discharges water into the ground, and the quantity of such is important so as to avoid damage to the environment. If your septic tank discharges two cubic metres or less above ground, then you don’t need to register it. If it releases five cubic metres, or less, below ground level then it is also exempt.
Do I need consent to discharge septic tank?
You will require a ‘Permit to Discharge’, however you may qualify for an exempt status if your system meets certain requirements such as amount of discharge, septic tank or sewage treatment plant model (only EN 12566-3 2005 Certified plants accepted), plant location, intended discharge point, installation and
Can you use a metal detector to find sewer lines?
Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.
Are septic tanks metal?
Steel Septic Tank—Steel septic tanks are the least durable and least popular tank option. Designed to last no more than 20-25 years, they can be susceptible to rust even before that. Steel top covers can rust through and cause an unsuspecting person to fall into the tank.
Are septic tanks made of metal?
The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.
How To Find Septic Tank Location: A Guide for Property Owners
The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.
Follow the Main Sewer Line
Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.
If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.
Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.
Inspect Your Property
Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.
If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.
Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.
- Paved surfaces
- Unique landscaping
- Your water well, if you have one
- And other features.
If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.
Check the Property Records
Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.
Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.
Don’t Try to Fix Septic Tank Issues Yourself
Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.
Schedule Septic Tank Maintenance
The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.
We are open seven days a week, twenty-four hours a day.
Frequently Asked Questions
A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.
How do I know if I have a septic tank?
Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.
If you’re also using well water, it’s possible that you won’t receive one at all.
What do I do once I locate my septic tank?
Once you’ve discovered where your septic tank is, there are a few things you should do. It is critical to clearly mark the position of your septic tank. With our inspection, pumping, and repair services, you can save time whether you need a sewer line cleanout or a septic tank maintenance job completed quickly. Make a note of the location of your tank so that you can find it again if necessary. It should be heavy enough so that it does not fly away in windy conditions. A creative approach to accomplish this without having an unattractive flag or marking in your yard is to use garden décor or a potted plant.
This way, you’ll have it for future reference and will be able to quickly locate the exact position if necessary.
Then contact The Original Plumber to have your septic system maintained on a regular basis. Preventing worse problems and the need for costly repairs down the line may be accomplished via proper septic system maintenance. All of the heavy lifting has been delegated to our team of professionals.
How To Find My Septic Tank
- What is a septic tank
- How do I know if I have a septic tank
- And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
- What to Do Once You’ve Discovered Your Septic Tank
You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.
- “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
- When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
- The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
- In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.
How to Locate Your Septic Tank
Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.
What Is a Septic Tank?
Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.
Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.
How Do I Know If I Have a Septic Tank?
What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.
- A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
- A septic system is likely to be installed in your home if you reside in a rather rural location.
- Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
- When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
- Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.
Why It’s Important to Know the Location of Your Septic Tank
You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:
1. To Be Able to Care for It Properly
The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.
2. If You Want to Landscape or Remodel Your Property
If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.
For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.
3. If a Problem With Your Tank Occurs
Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.
4. Ease of Getting It Fixed
Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away
1. Use a Septic Tank Map
First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.
- If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
- The county health department is responsible for keeping track of septic systems.
- A septic tank’s position could be depicted on a survey map, for example.
- The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.
2. Follow the Pipes to Find Your Septic Tank
Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.
- In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
- By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
- The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
- Going via the sewage line itself is another method of locating the septic tank utilizing it.
- Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
- When the snake comes to a complete halt, it has almost certainly reached the tank.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.
If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.
3. Inspect Your Yard
Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:
- Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
- Directly in front of the home Immediately adjacent to your well (if you have one)
- In close proximity to trees or densely planted regions
- In the shadow of a patio, deck, or other building
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.
Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.
4. Talk to Your Neighbors
If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.
5. Look for Your Septic Tank Lid
It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.
The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.
What to Do After You Find Your Septic Tank
Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.
However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.
1. Mark Its Location
The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.
2. Take Care of Your Septic Tank
Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.
In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.
For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.
Call a Professional Plumber
Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.
Request an Estimate for the Job
Looking for Your Septic Tank? Here’s How to Find It
“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved.
Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property. If you’re looking for a tank, we have some suggestions that may be of assistance.
Why you need to know where your septic tank is located
If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.
In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.
How to find your septic tank
- Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
- Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.
After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.
- The post was published on July 16, 2019 under the category Septic Tank System.
How To Locate a Septic Tank
Customers frequently inquire about the location of a septic tank. Unless your septic tank is equipped with special risers that elevate the lids above ground level, you may need to enlist the assistance of a qualified professional. However, there are a number of things you may do to prepare yourself before calling for assistance. When it comes time to have your septic system repaired, being how to find your own septic system will save you money. Public health records can be obtained by contacting your local health department.
- These permits should be accompanied by a graphic depicting the location of the septic system’s burying spot.
- Public Records Request for the County of Nevada Request for Public Records from the County of Placer Examine the findings of your inspection report.
- Make contact with the construction company that built your home.
- Find the location of the main sewer line.
- Locate the 4 inch sewer pipe that runs through your basement or crawlspace and take a measurement of the point at which it leaves the home.
- By carefully probing the yard every few feet and following the septic pipe across your yard, you should be able to detect any problems.
- The majority of septic tanks are placed 1 to 3 feet below and are located roughly 10 to 20 feet away from the house.
An electronic metal detector can find the reinforcing bars in a concrete tank if it is built out of concrete.
Please contact us.
We have specialized technology that we can use to pinpoint the location of your tank.
You should make a note of the position of your tank for future reference if you were successful in discovering it.
A riser elevates the septic lid above the ground, making it easier to find and access your septic tank and its contents.
As a result, you will not have to pay a professional to identify and dig up the lids every time your septic system is repaired, which will help to protect your landscape and save you money.
How to Find Your Septic Tank
Riverside, California 92504-17333 Van Buren Boulevard Call us right now at (951) 780-5922. Knowing where your septic tank is located on your property is critical to doing routine maintenance on your septic system. Eventually, all septic tanks will become overflowing and will require pumping. When your tank’s lid is difficult to locate, you may be at a loss for what to do or where to look for the lid when you need it. Most septic tanks are designed to be as unobtrusive as possible, making it quite difficult to locate one on your own in most cases.
If you remove the lids yourself, you run the risk of causing a septic system to collapse or a leaky system to transmit bacterial or viral diseases due to filthy circumstances.
Check the Map
The most straightforward method of locating your tank lid is to review the records. It is recommended that you submit this map with your home inspection documentation if you have recently acquired the property. If you don’t have one, you can request one from the county. The majority of septic systems come with a comprehensive map that will assist you in locating the lid. Because the data are normally so thorough, you can usually measure your way to the precise site.
Pipes Lead the Way
Every septic tank is connected to the main sewage line that runs from your house. You may follow this line all the way from its starting point at the home to the tank’s site. Fortunately for individuals who choose this strategy, there is no digging involved! Simply use a metal rod to probe the ground for the line, then follow it with your eyes closed. It is common for tanks to be positioned 10 to 25 feet from a home’s foundation and to be built of concrete, fiberglass, or polyethylene material.
Look For Signs
For whatever reason you do not have access to a map, or if you do have access to a map but are having difficulty locating the sewage line, you can seek for ground markers to guide you. Small hills or pits that appear to be out of place might be an indication of an earthquake. Even in the presence of grass or other plants, a septic tank with a surface area of 40 square feet will leave a little distortion in the ground, even if the tank is not completely filled. If none of the aforementioned approaches succeed in locating your tank lid, you may always engage the assistance of a knowledgeable specialist.
No matter how you establish the position of your septic system, make a note of it in your records or plainly mark the place with a permanent marker to avoid future complications and problems.
Contact Us Today
We at West Coast Sanitation understand that you are busy and do not have time to deal with septic issues. One of the most effective methods to maintain this balance and ensure that your septic system continues to function properly is to have your tank pumped on a regular basis.
If you want assistance in identifying or maintaining your septic system, don’t hesitate to contact us. Please contact us at (951) 780-5922 as soon as possible. If you have any questions, we have specialists standing by to help you resolve them and get your system back up and running.
How to Find Septic Tanks
Every septic tank will eventually get clogged with solid waste and will need to be drained and cleaned. Pumping out the septic system on a regular basis is essential to maintaining it in excellent functioning order. But what can you do if you don’t know where the septic tank is? What are your options? How to locate and locate your septic tank will be covered in this section. Septic tanks should not be installed in any one location because each property is unique. Septic tanks are difficult to detect, but there are several principles and indicators that might assist you.
How to Locate Septic Tanks: Using Public Records:
- Inquire with the previous owner of the property. This may be the quickest and most convenient method of locating a septic tank. Simply contact the previous owner and inquire as to the whereabouts of his or her septic tank. In spite of the fact that the previous owner should have shared this information with you when selling the home, it is easy to forget normal maintenance data. If you are unable to contact the previous owner or if the previous owner does not know the location of the septic tank, do not give up hope just yet. There are several alternative methods of locating a septic tank
- However, Consult the County Records for more information. The county should have a copy of the septic tank installation permit documents for your property on file. This file should include a schematic or map of the property that shows the location of the septic tank. If the septic tank was erected more than a decade ago, the information may or may not be on file. Call a few different septic tank pumping companies in your area. It’s conceivable that your septic tank was installed by a local business or contractor. Check with several businesses to check whether they have your address on file.
How to Identify Septic Tanks on Your Own Septic tanks are hardly the most visually appealing or pleasurable of systems to see. They are installed in such a way that they are hardly visible and are not visually highlighted or exhibited. In the event that your septic tank is actively being concealed, you will have to figure out how to locate it. One method of locating the septic tank is to trace the waste line from the house to the septic tank’s location. Identify where the sewage line departs the home, which is usually in the basement, and then travel to the same location outside the property.
Consider the area where a septic tank is most likely to be found.
- Usually between 10 and 20 feet away from the structure. It should not be too near for reasons of health and safety. When it comes to building costs, it is preferable to keep excavating to a minimum by not locating it too far away. From the house, it’s all downhill. Gravity is used to transfer waste in the majority of plumbing systems. This is not always the case, however, because certain systems make use of pumps. Is there a well, a stream, or any other site feature on your property that might have an impact on the installation of a septic tank? There cannot be a septic tank in close proximity to wells or the property line. Seek out bald places where there is no grass growth, which might indicate the presence of a shallow-buried septic tank top. Locate any green grass, which may be indicative of a septic tank that is overflowing or leaking
- Assuming you already know where to go, here’s what you should be looking for now:
How to Locate Septic Tanks Using Visual Indications
- What is the appearance of a septic tank? Septic tanks are rectangular in shape and measure around 4ft x 8ft. Knowing this, seek for a rectangular depression or a rectangular region of sparse grass growth in a rectangle area of sparse vegetation. When septic tanks are placed shallowly and close to the surface, the outcome is often sparse or uneven grass growth
- This is due to the fact that they are buried shallowly and close to the surface. Pipes that are unexplained. Air vents and cleanouts are common features of septic systems. If you notice pipes jutting out of the ground, it is possible that they are for the septic system. Copper is not used in the construction of these pipes, which are typically 4 to 6 inches in diameter and composed of cast iron or white or black plastic. Detecting an unpleasant odor implies that you have located the drainfield and that it is failing
- Wet places that haven’t been explained. if there is an area of your land that is perpetually wet or moist for no apparent reason, it is possible that this is the location of your septic tank. Most of the time, it is accompanied by disagreeable smells. Look for markers such as a stake, stones, or other sorts of objects. In order to indicate the position of the septic tank’s pumpout access, it is customary practice to post a marker. Boxes for electrical equipment. Pumps and grinders are commonly seen in septic tanks that are powered by electricity. If you have an electrical connection or box protruding from the ground distant from the home and are unsure what it is for, it is possible that it is for the septic system
- Lush green grass
- Or irrigation system. This might be the case if your property has a single patch with especially lush green grass and you have not watered or fertilized it. If this is the case, the septic tank may be positioned in this location. Unfortunately, that lush green grass indicates that you are experiencing seepage from your septic tank
- Nonetheless, Random dirt depressions in the earth, each measuring around 2 square feet, which may indicate a former excavation for tank pumping
If you are still unable to locate the septic tank, it is likely that you should contact a professional. A professional sewer tank plumber will locate and service septic systems on a regular basis and will be equipped with the required equipment and knowledge to locate your home’s septic tank swiftly and efficiently. Don’t be tempted to lift the lid or conduct any other work on your septic tank now that you know where to look. Septic tank lids are extremely heavy, and septic tanks emit harmful vapors.
Always get your septic tank serviced by a licensed and insured septic tank plumber.
There are a few solutions available if the previous homeowner failed to supply this critical information or if you have misplaced your original copy:
- Your local DHEC office may have a copy of your building permit on file if your house was built within the last five years or fewer, according to the DHEC. A copy of a septic tank permit can be obtained from the local office by any individual or group, regardless of whether or not they own the land in question. Because of this, it is highly recommended that you have as much of the following information as possible ready at the time of your request.
- Number of the tax map
- Lot number
- Block number
- Address in the physical world
- When the system was installed or when the house was built (if this information is available)
- Name of the original permit holder (if any information is available)
- Name of the subdivision (if the property is located within a subdivision)
- You may also submit a request for a copy of the permission through our Freedom of Information office, although this is not mandatory. To obtain a copy through the Freedom of Information Office, please complete and submit a copy of the DHEC FOI form. Instructions are given with the application. If feasible, please include the information about the property that is stated above. When looking around your yard, search for manhole covers or lids that have been buried by grass or leaves if your house was constructed before 1990.
Septic Tank Alerts Septic Tank Alerts
How to Locate Your Septic Tank
It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.
This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.
How To Find A Septic Tank: Step By Step
It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.
1. Gather Some Helpful Tools
Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.
Using this method, you may also locate the cover for your septic tank.
While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.
2. Use a Septic Tank Map
If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation. You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.
3. Start Ruling Areas Out
The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:
- Immediately adjacent to your well
- Beneath your home
- Directly against your home
- For example, underneath your driveway
- Under trees
- And other locations. Structures like a patio or deck are good examples of this.
4. Inspect Your Property
If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.
When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.
The likelihood of your septic tank being discovered in a few specific locations is quite high. Because of code issues or just because it doesn’t make sense, it’s highly unlikely that your septic tank will be located near any of the following locations:
- Your water well, if you have one (for a variety of reasons that are rather clear)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
- Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping
5. Inspect Your Yard
A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:
- If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
- Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.
The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.
6. Follow Your Sewer Main/Sewer Pipes
Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.
The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.
If the line is labeled, it is usually made of plastic or rubber.
7. Check Your Property Records
Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.
If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.
What to Do Once You Find Your Septic Tank
Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities.
You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!
Online Septic Search
For residents in Indian River County as well as contractors and realtors, Septic SearchTMis a free web service that may be accessed over the Internet. This service will assist agencies, homeowners, buyers, sellers, contractors, and real estate agents in knowing more about the existing septic systems and wells in their communities. The Indian River County Department of Health has made its septic system and water well documentation available to the public on the internet. Site plans that were scanned are accessible for permits that were granted after January 1, 2000.
- Obtaining applications, permits, repairing or replacing an existing system, site evaluations, and inspections
To look for information on current septic systems and wells, go to the following website:
- Indian River County is a good choice. then pick Records Search from the drop-down menu. In the Indian River County Property Appraiser’s database, you may search by address or tax parcel number. Once your property has been located, click on View History. SelectView to show the scanned documents that are currently accessible for the property
- The green arrow at the top of each document allows you to navigate through the other papers after they have been opened.
If you require assistance or have any questions, please call the Environmental Health Office at (712) 794-7440 or send an email.
Online Septic Research
The Environmental Services Department of Maricopa County maintains a database that contains all of the county’s existing approved septic systems for the purpose of preservation. Please bear in mind that property owners are responsible for maintaining accurate records of the location and maintenance of their septic system for the duration of the system’s life.
An Alteration Permit will be required for onsite systems that have a failing tank or disposal field.
An Abandonment Permit will be required for any onsite systems that are to be abandoned in order to connect to the municipal sewage system or that are to be taken out of operation.
Option 1: You may perform your own study at no cost by using the Online Septic Search Tool (available at no expense). Option 2: You can call the Environmental Services Department and ask for a more in-depth search to be undertaken (fees will apply for research conducted by the department for each parcel).
- Researchers charge a fee of $30 for research requests that take 3 to 7 business days. Expedited researchers charge a $60 fee for research requests that take 1 to 2 business days. Septic Research Request Form.