How To Install A Riser On A Plastic Septic Tank? (TOP 5 Tips)

How To Instal Risers On A Septic Tank

Step 1 – Gather The Parts You Need.
Step 2 – Clean The Top Of Your Septic Tank.

Step 3 – Apply Butyl Rope To Tank Adapter Ring.
Step 4 – Put Adapter Ring Around Hole And Screw It Down.
Step 5 – Add Butyl Rope To The Bottom Of Each Riser.

Step 6 – Put Risers and Lids On The Adapter Ring.

How do you keep a plastic septic tank from floating?

How can you prevent this from happening?

Fill the tank with water after it’s pumped to keep weight in the tank and prevent floating.

Divert rainwater runoff away from your system.
Avoid pumping the tank during wet seasons if there is a risk that the tank could float.

Should I install a riser on my septic tank?

Having a riser in place can also significantly reduce the cost of septic tank maintenance over time through the ease of access and time on the job saved. Plus you will be spared digging up your lawn every time as well.

How far apart are septic tank lids?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

How many lids are on a septic tank?

A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle. A two-compartment tank installed after 1975 will have two lids of either fiberglass or polyethylene, centered at opposite ends of the rectangle.

How much does it cost to install risers on a septic?

Septic tank risers are not only convenient, but they are also cost-effective if you plan to say in your home for several years. Plastic septic tank risers typically cost $300 to $400 to install, parts and labor included.

Do they make square risers for septic tanks?

The Polylok square riser adapter ring is designed to connect the Polylok septic tank risers or lids to an existing concrete tank with large square or round openings.

How can buoyancy be prevented?

Buoyancy countermeasures

Base extension (cast-in-place or precast). Using the additional weight of soil by adding shelves is a common method used to counteract buoyancy.
Anti-flotation slab.
Increase member thickness.

Lower structure elevation and fill with additional concrete.

Will a septic tank float out of the ground?

A septic tank may also float out of place if it’s pumped while the ground is flooded. This can damage inlet and outlet pipes. Your system does need to be pumped as soon as possible after the water table is lowered. Before this happens, don’t drive any machinery near the septic area to avoid compressing the soil.

How to Install Septic Tank Risers

A septic-tank riser is a pipe that goes from a septic tank to the surface in order to raise the tank’s lid. Installation of these low-cost devices eliminates the need to dig in order to reach the tank’s lid for inspection or maintenance purposes, saving you time and money. To place risers on your tank without needing to employ a professional, simply follow these instructions.

Step 1 – Choose the Material

The materials used to make risers include concrete, polyvinyl chloride (PVC), and polyethylene. Concrete is the most common material utilized. The pricing, durability, and convenience of installation of these three materials are all different. Even while concrete is the most inexpensive material, it is also the most difficult to install due to its weight. Risers made of polyethylene are lighter and quicker to install, and they are more resistant to soil erosion than steel risers. They are, however, more susceptible to gas and water leaks than other alternatives.

This material is not only simple to install, but it also does not readily leak water or gas when exposed to extreme temperatures.

Step 2 – Decide Where to Install the Risers

Risers are used to replace the cover of the septic tank and to allow access to the tank closer to the ground’s surface. This access can be constructed above ground, where the risers are clearly visible, or it can be installed close below the surface, where the risers are not visible. Typically, above-ground installation is employed in regions that are neither visible nor interfere with grass maintenance procedures. Installing risers above ground also makes it easier to get to the tank when it is needed.

While this approach makes the risers more inconspicuous, you will have to remove the grass that has grown on top of the risers every time you need to get access to the tank in this manner.

Step 3 – Determine the Height

Septic tanks can be buried as far as three feet below the surface of the ground, although the typical depth is 18 inches, according to the EPA. Risers are available in two different heights: 6 inches and 12 inches. They are built on top of one another until they reach the surface or come to a halt just below the surface of the water. Measure the distance between the tank and the location where the new lid will be put in order to calculate the number of risers that will be required.

Step 4 – Gain Access to the Septic-Tank Lid

In order to install risers, you must first dig down to the septic tank’s lid in order to obtain access to the tank. Allow ample space, roughly 2 feet in all directions, for the installer to be able to move around without being obstructed.

Step 5 – Install an Adapter Ring

Remove the current septic tank cover from its position. Make use of an adapter ring to seal up the entry to the septic system. All of the risers will be attached to this ring at the same time. Concrete is used to hold the ring to the tank in place.

Step 6 – Install the Risers

Install as many risers as necessary to attain the requisite height for an above- or below-ground installation, depending on the situation.

Screwing the risers together will allow them to be connected to one another. The fact that they are screwed together makes them watertight and airtight. It is simple to repair a septic-tank riser if one is ever damaged or destroyed.

Step 7 – Install a New Lid

Lids are available in a variety of sizes. Select a lid based on the size of the risers that you want to use. Installation Instructions: Place it on top of the final riser and fasten it using the two pins that are included.

Installing Access Risers

In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below. Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.

A few safety tips before you get started:

Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website

Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.

Gather all the MaterialsTools You will Need

It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.

Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.

Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.

See below for Step 4 on attaching risers to the tank entrance.

Tank Adapter Ring (TAR)

Riser Adapter Ring Kit
Butyl Rope
Risers

Domed Lid OR Flat Lid
Stainless Steel Screws

The following materials will be required for digging up your septic tank(s):

As-built condition of the sewage treatment system The following items are required: sketch on paper, measuring tape, shovel, probing instrument, eye protection, and work gloves.

To cut risers to the proper size, the following tools are required:

Circular saws, saber/jig saws, and hand saws

Drilling with a 1/4-inch bit File containing Raspor
Markingpen
A tape measure is a tool used to measure anything.

Materials required to seal the risers to the tank include:

High-strength concrete patch mix
A small bucket

A mixing stick
And gloves

Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.

Step 1: LocateYour Septic Tank(s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.

Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.

The presence of underground electricity or other utility lines and cables might put your septic tank in danger.

If you run into a power line, the consequences could be fatal. Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.

Step 2: Uncover Your Septic Tank (s)

Once you’ve discovered your septic tank, you may start digging about. The tank is typically 6 feet wide by 8 feet long, with the width being the largest size. Remove all of the pebbles and debris from around the tank’s lid openings and dig out the whole top of the tank. You will want to clean out any dirt that has accumulated on the surface of your septic tank. This will assist you in ensuring that you generate a high-quality seal. You should have two openings: one over the inlet (which comes from the home) and another over the outlet (which comes from the yard) (into the drainfield or pump chamber).

You’ll need a riser for each of the doors you open.

Typically, the inlet side is the one that is nearest to the home.
When cleaning the tank, it is beneficial to remove the complete top of the tank.
Risers must be modified in order to be correctly installed, and all manholes (holes 24 inches or bigger in diameter or square in shape) must also be updated, as well as the tankinlet and outlet baffle covers (if separate from the manholes).

If you discover one – and only one – riser already installed, it is most likely for the pump chamber, which only requires a single riser to provide access to the pump to function properly.
Remove the concrete lids so that they may be disposed when the project is completed.
Consult your’As-built’Recorddrawing to establish whether you have a distribution box (D-box), which you will also need to unearth and place a riser on if you have a typical gravity system.

Once the lids have been removed, proceed with caution around the tank.
Inform someone of your whereabouts in case you are involved in an accident.

You should be aware that exposure to sewage can result in serious sickness, so make sure you wear gloves and thoroughly wash your hands afterward with soap and water. It is also recommended that you wear eye protection in the event that debris falls into a tank and splashes back at you.

Step 3: Fit Risers to Component Openings

In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:

Theriser will fit into the tank hole if the aperture is between 26 and 29 inches in diameter. Measure the distance from the ground to the top of the septic tank and multiply the measurement by three inches. The following is required if the aperture is greater than 29 inches: a 3-foot square fiberglass plate (with a 22-inch hole in the middle) is required. In this case, it lies above the manhole and narrows the aperture, allowing a 24-inch riser to be utilized instead of a more expensive 30-inch riser, saving money.

The distance between the ground and the top of the fiberglass plate should be measured. You may choose to place the risers so that they are level with the surface of the ground, or you may want them to stand out a few inches above the ground (if a riser is above ground make sure you are careful when mowing). Tips: To shorten a big riser with ribs, drill a 1/4-inch hole between the ribs above the cut line and finish the cut by following one of the grooves between the ribs with a saber/jig saw to finish the cut.

By eliminating one of the ribs from the largeriser, it may be made to fit more snugly into a smaller manhole entrance.

Step 4: Attach Risers toSeptic Tank (s)

It is recommended to pump out an old septic tank that is 20 years or older in order to check its structural integrity and water-tightness before using it again. If the tank requires extensive repairs, it is preferable to replace it with a new septic tank that includes risers as part of the installation. A permit from the local health department is required for the replacement of a septic tank. Remove any dirt and debris from the tank’s surface by cleaning it off. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s instructions.

Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names available.
NOTE: For optimal results, just a little amount of concrete patch should be mixed at a time.

The patch mix should be used to seal the riser to the septic tank.
If you want to avoid a safety danger, make sure you properly attach theriser lid using the screws that come with it!
Risers for inlet or outlet apertures that are smaller than the openings should have the bottom few inches sanded with rough sandpaper to allow a firmer connection between the two surfaces.

A useful source of information on correct installation of risers on septic tanks may be found at your local hardware store where you purchased the risers and covers.

Thurston County Environmental Health is should be commended for providing the foundation for this documentation.

What You Should Know About Septic Tank Risers

Septic tank risers are an important part of any septic system, and they should be installed in every property. This article will provide you an overview of septic tank risers and how they may help your septic system. What Is the Function of a Septic Tank Riser? A septic tank riser is a conduit that connects your home’s surface drainage system to your septic tank beneath the ground level. An access port or the pump-out ports on the septic tank are where the riser connects to the tank. Septic tank risers are equipped with lids that can be quickly removed to allow you to check or pump your septic tank without having to dig up your yard.

These structures are often made of materials that disintegrate slowly over time, such as plastic or concrete.

What Are the Advantages of Using Risers?
Normally, this entails digging up your yard before the pump is installed and reburying the tank once it has been installed.
The use of a septic tank riser can help to minimize the amount of time spent pumping your septic tank.

The fact that the riser is visible above the surface of your yard makes it an ideal signal for locating your septic tank the first time you need to discover one in your yard.
For those who want to stay in their house for several years, septic tank risers are not only handy, but they are also cost-effective.
Concrete risers are more durable, but they are also more expensive, and the price will be determined by the quote you receive from the contractor who will be installing them.

Because labor expenses account for a large amount of the fees that contractors charge for septic system inspection and pumping, installing a riser may possibly reduce the future cost of septic service by as much as 50 percent.

Each and every property can profit from the installation of a septic tank riser, but this does not imply that you should do so immediately.

This allows for the installation of the pump and riser to be completed in a single step.

Because a riser should be considered a long-term investment, you should be certain that your tank is in good functioning shape before installing one.

A septic tank riser is a straightforward concept that may save you a significant amount of money and pain when it comes to septic system maintenance and repair.

We look forward to hearing from you and addressing any concerns you may have concerning your septic system requirements. Contact us now. Please let us know how we may be of assistance to you and your septic system right now!

Steps that you should follow to install risers on a septic tank

Septic tank risers are an important component of any septic system, and they should be installed in every property. Read this article to learn more about septic tank risers and how they might be beneficial to your septic tank. An explanation of what a Septic Tank Riser is, and how it works. In your yard, a septic tank riser is a conduit that connects the surface of the earth to the subterranean septic tank system. Septic tank risers are connected to septic tanks at the pump-out apertures or the access port.

Rising sewer lines must be constructed to endure harsh weather conditions.
When a new septic tank is installed, risers are nearly usually included; however, many homes with septic systems installed in the recent decade did not include risers.
It is recommended that you pump out your septic system every three to five years by the majority of septic system manufacturers and septic system contractors.

A septic tank not being where the contractor expected it to be will result in twice the amount of work being done to dig a new hole and find the tank, which will result in a higher cost.
Simply remove the secure lid of the riser and insert a pump line into it to get access to your tank, and your contractor will be on his or her way!
When it comes to the cost of a riser, Sitting in your house for numerous years means that septic tank risers will not only be handy, but they will also be cost-effective.

Concrete risers are more durable, but they are also more expensive, and the price will be determined by the proposal you receive from the contractor who will be installing them for you.

Due to the fact that labor expenses account for a large amount of the fees that contractors charge for septic system inspection and pumping, installing a riser may possibly reduce the future cost of septic service by half.

Despite the fact that every property might profit from the installation of a septic tank riser, this does not imply that you should do so immediately.

This allows for the installation of the pump and riser to be completed in a single operation.

You want to make sure that your tank is in good functioning shape before adding a riser since it should be considered a long-term investment.

It is a basic notion, but one that may save you a lot of money and heartache when it comes to septic system upkeep.

can help you if your septic system is in need of a riser or any other type of servicing. The opportunity to hear from you and answer all of your septic system-related inquiries is a privilege we welcome. Please let us know how we may be of assistance to you and your septic system right now.

Where does this waste water originate from? Toilets, showers, sinks, dishwashers, and washing machines are all potential sources.

It’s critical to understand how your septic system operates and why flushing particles and chemicals down the toilet can have negative consequences. This might result in the need for more regular septic tank services, which no one wants to deal with. As you are undoubtedly aware, a septic tank is extremely essential since it aids in the separation of particles from wastewater, allowing as much of the material as possible to decompose as the liquid runs to the drain field and into the environment.

Installing risers on a septic tank with Blue Diamond pumps makes a lot of sense since they will make pumping, inspection, and maintenance much easier; not to mention the fact that they are required by law in many areas.

1.Get all the necessary parts together

In order to prepare to build a riser system on your septic tank, you will need to purchase a few goods. These items include a Tuf-Tite tank adapter ring (TAR), a kit for riser adapter rings, butyl rope, Tuf-Tite risers, a Tuf-Tite domed lid or a Tuf-Tite flat lid, and stainless steel screws. The adapter, lid, and risers should all be slightly bigger in diameter than the hole in your septic tank.

2.Make sure the top of the septic tank is clean

One of the most important steps in ensuring that you do a good job of installing risers on your septic tank is to ensure that you create a good seal; this means that you must ensure that the top of your septic tank is perfectly clean so that dirt does not ruin the seal during the installation process.

3.Applying the butyl rope to your tank adapter ring

The butyl rope that you ordered is primarily intended to assist you in achieving a watertight seal on your container. Your butyl rope must be applied carefully and methodically, immediately to the bottom of your Tuf-Tite tank adapter ring, making certain that it is applied completely around your tank adapter ring. Again, getting this correctly ensures a water-tight seal, so take your time and do it perfectly the first time.

4.Putting the adapter ring in place properly

The next stage in the process of placing risers on your septic tank is to ensure that the Tuf-Tite tankadapter ring is correctly secured in place. You’ll want to press the adapter ring onto the septic tank with a little force to ensure that it stays in place. As part of the package that you ordered, you should have a drill bit that will enable you to begin drilling holes in the areas where you see divots on the adapter ring. As soon as the holes are drilled, you may use the tapping screws that included with the package to fasten the adapter ring to the top of your system in the right manner.

5.Apply butyl rope to the risers

In order to make each riser watertight, butyl rope should be wrapped around the recessed rings on the bottom of each one.

6.Place the risers on the adapter ring

In order to make each riser watertight, butyl rope should be wrapped around the recessed rings at the bottom of each one.

Why You Should Install a Septic Tank Riser

Septic tank risers make it easier to access and pump your septic tank, which is beneficial for doing routine maintenance. Unfortunately, many older septic tank models are not equipped with septic risers, resulting in many homeowners being unsure of the location of their septic tank. When it comes to inspection and pumping appointments, homeowners who aren’t sure where their septic tank is are left with three choices: The following options are available: 1) examine public records to obtain a comprehensive map of their land, 2) dig up their yard, or 3) hire a plumber to dig up their yard and locate the tank.

By adding a septic tank riser, you may completely remove all of these issues. Continue reading to find out more information.

What Is a Septic Tank Riser?

A septic tank riser is a pipe made of plastic, concrete, or fiberglass that rises vertically from the septic tank to the ground level, allowing you to have direct and simple access to your septic tank and drain field. At the top of the pipe, a lid is installed, which can either be left open to allow for simple identification or covered with a very thin layer of earth or grass. The following are the four most significant advantages of adding a septic tank riser:

There will be no more digging: It is possible to look forward to never having to dig up your yard again for an inspection or pumping service once your tank riser has been placed. During the winter, it is simple to go there: Digging up the earth to get to your tank during the winter months may be extremely difficult, if not impossible, when the ground is frozen. Thanks to a septic tank riser, you may connect your tank directly to the rest of your system. Saves money in the following ways: During an inspection visit, most plumbing firms will charge you a lot of money if they are unable to locate your septic tank. A septic riser assists the plumber in quickly locating your tank, ensuring that you never have to worry about additional expenses. Saves time by avoiding repetitive tasks: It might take many hours to locate your septic tank. It is no longer necessary to hunt across your whole yard for your septic tank riser, which saves you a significant amount of time anytime you have maintenance appointments.

Call The Plumbing Experts!

Are you ready to put in a septic tank riser? The Plumbing Experts are there to assist you! Our professional plumbers are knowledgeable with all brands, models, and sizes of septic tanks, and they are here to make septic tank maintenance much easier by installing a septic riser in your system. Contact us today to learn more about our septic tank installation services. Our septic tank services include the following:

Septic tank repair, septic tank installation, and septic tank pumping are all services that we provide.

Sewage tank repair, installation, and pumping are all services that may be performed on a septic tank.

What Are Septic Tank Risers? – Septic Tank Pumping – B&B Pumping – Top Rated Septic Cleaning Services

Without a doubt, septic tanks are shrouded in mystery, which only adds to their intrigue. You might not think about your septic tank very often because it is buried beneath the earth and just has a cover to indicate its location. Inspection and pumping of your septic tank, on the other hand, may be a time-consuming and expensive operation, particularly if you are having a severe problem with your septic system. For this reason, we discuss new and beneficial features on our blog, such as septic tank risers, in order to make septic tank pumping more accessible for our clients.

Septic Tank Risers

Without a doubt, septic tanks are shrouded in mystery, and this is understandable. Septic tanks are commonly forgotten about since they are buried beneath the earth and only accessible by lifting a lid. Inspection and pumping of your septic tank, on the other hand, may be a time-consuming and expensive operation, particularly if you are suffering a severe issue with your septic system. Our company is dedicated to making septic tank pumping more accessible to our customers, which is why we highlight creative and beneficial features on our site, such as septic tank risers.

Your Local, Premier Septic Tank Pumping Company

We at BB Pumping are here to help you if your house in the Fort Worth region is in need of septic tank services. We proudly serve residents of Fort Worth, Decatur, Azle, Haslet, and Weatherford among other communities. Septic tank problems may be resolved quickly and inexpensively by our team of experts, and we can also provide you with the regular maintenance you require to keep your septic tank system functioning properly. Call us now to set up an appointment for servicing! OUR PRODUCTS AND SERVICES GET IN TOUCH WITH US

What is a Septic Tank Riser and How Do You Install One?

Disclosure: This post contains affiliate links, which means that if you purchase a product after clicking on one of our links, we may receive a commission or free product from the firms featured in this post. Amazon is a good illustration of this. When you purchase a new house with a septic tank, there are numerous phrases that you may not have previously heard of or understood; one of these terms was Septic Tank Riser, which was new to me at the time. What is a Septic Tank Riser and how does it work?

It can be made of plastic or concrete. Older septic tanks were frequently erected without a riser, which meant that their access ports were underground and needed the removal of the topsoil in order to be accessed.

Why Do You Need a Septic Tank Riser?

A septic tank riser is required for a variety of reasons, which you may wonder why you require one in the first place. Allow us to explain why you would want to access your septic tank access port in order to have a better understanding of what we are talking about. Whenever you need to empty your septic tank, you must get access to the pump-out outlet on the side of the tank. You will need to pump your tank about every three years, depending on the size of your tank, the number of people living in the house, and the amount of demand placed on the system.

Find the location of your septic tank. Make a mental note of the region above the access ports (you better hope you’ve properly designated this)

Dig down as far as you possibly can till you reach the tank.

Depending on the depth of your plumbing and the shape of your land, the depth of your septic tank will vary. However, it is not uncommon for your septic tank access ports to be around 4 feet below the level of the service line. As a result, if you have a septic tank that does not have risers built, you will have to perform some digging every time you need to reach your septic tank.

What are the Pros and Cons of Installing a Septic Tank Riser?

The apparent advantage is that you will make it much easier to reach your septic tank pumping port

Nevertheless, When you need to have your tank emptied, this will save you a significant amount of time and effort. Additionally, if you are unable to perform the digging yourself, you will almost always see an increase in the price of your septic tank service bill owing to the additional time and effort that your pumping business will have to put in when pumping your septic tank. The presence of a septic tank riser will make it easier for purchasers who are inexperienced with septic systems to comprehend the system if you decide to sell your home.

Cons of Septic Tank Risers

The most significant disadvantage of installing septic tank risers on your septic tank is that the lids will now be visible on the surface of your lawn, which can be a safety hazard. Which might be rather unsightly
A septic tank riser will need to be installed if your tank does not already have one

Otherwise, you will have to pay money to have one installed.

Can You Install a Septic Tank Riser on an Older Septic System?

It is quite likely that your septic system will have septic tank risers if you are having a new system installed. For those who have an older septic system, there is the possibility that your present septic system does not have septic tank risers installed. As a result, you may wonder if it is possible to put septic tank risers on an older septic tank. A septic tank riser may be installed on an older septic tank, and this is the correct answer.

How to Install a Septic Tank Riser?

Installing a septic tank riser on an older septic system may be accomplished in two different ways.

Obtain the Services of a Septic Tank Professional: This is self-explanatory, but if you’re not handy, like me, you might not realize it. You should next get in touch with a local septic tank specialist and inform them that you have an older septic tank and that you would want septic tank risers to be fitted. To learn more, please visit this page. If you need assistance locating a local septic tank service, please contact us. Installing a septic tank riser on your own is possible if you follow these steps: If you opt to do it yourself, you will be able to successfully install a septic tank riser.

DIY- How to Install a Septic Tank Riser Yourself?

So, if you decide to build your septic tank riser on your own, these are the procedures you will need to do.

Septic Tank Riser

Transition Ring
Caulk Gun with Henry’s Roofing Tar
Septic Tank Riser Lid

Septic Tank Riser

TO MAKE SURE THAT YOU GET THE RIGHT SIZES OF EVERYTHING, MAKE SURE THAT YOU CHECK THE SEPTIC TANK RISER, ADAPTIVE RING, AND LID FOR EACH ITEM. The following are the procedures you must follow in order to build your own septic tank riser on a concrete septic tank.

Find the location of your septic tank. Place the plants just over the access openings, to be more specific

Dig all the way down to the septic tank until you reach the top
Remove the concrete tank’s cover and set it aside. Measure the opening on the diagonal, from corner to corner, starting at one end and ending at the other. This will provide you with the information you want on the size of the riser. Make certain that you measure from corner to corner at an angle, otherwise you may end up with a diameter that is too tiny. Connect the Riser to the transition ring and apply the roofing tar where the two pieces come together. Roofing tar should be applied at the bottom of the transition ring. Afterwards, attach the septic tank riser just above the tank access hole.

Please see the video below for a fast demonstration of how to install septic tank risers in the correct manner. Installing your septic tank riser with anchors is a different method than the one described above.

What Brand of Septic Tank Riser is Best?

In terms of choosing an excellent septic tank riser, there are a handful of reliable manufacturers to consider. Tuf-Tite Septic Tank Risers, on the other hand, is the one that truly stands out in terms of consistent customer feedback. Because of this, you may find the Tuf-Tite Septic Tank Risers at your local septic tank wholesaler, or you can get them straight from Amazon, which is even more convenient. Here’s where you can get the most up-to-date pricing on Amazon. (Full disclosure: This is an affiliate link, which means that if you make a purchase after clicking on it, Amazon will provide me with a tiny commission.) If you do decide to go forward with it, please accept my thanks in advance.)

Adaptive Rings for Septic Tank Riser can be found at the lowest prices on Amazon
Click here to view the best Amazon pricing on Adaptive Rings for Septic Tank Riser.

Do I need to install a septic tank riser on my septic tank?

To see the best Amazon pricing on Septic Tank Riser Adaptive Rings, please visit this page: Septic Tank Riser Adaptive Rings (Amazon).

Can you hide your septic tank lids after installing a Septic tank Riser?

As a result, the purpose of installing a septic tank riser is to make it much simpler to really reach your septic tank, therefore you should be cautious while attempting to conceal it in your yard. Never cover it up with shrubs or with any other permanent building that would prevent you from accessing the port for your septic tank pumping system. However, having said that, I understand that having the lids in the center of your yard can be a little unattractive. Using camouflage style lid coverings, which are made to seem like rocks or other natural features on your lawn, is one option you might consider using.

Take a peek at this page if you want to see some great covers that look like rocks.

For those who require septic system servicing, our state by state list may help you locate a qualified local professional.

What is Septic Tank Riser

If you are one of the twenty percent of houses in the United States who are not linked to a centralized sewer system, the likelihood is that you have a septic system installed in your yard. A septic system is a sewage maintenance system that is installed on-site. While you are no longer required to pay monthly sewer fees to your local municipality, you are still responsible for the upkeep and maintenance of your septic tank system. Septic Connection, for example, is an excellent choice for an experienced septic service company in your area.

Installation of an aseptic tankriser can help to reduce the amount of time spent on sewer maintenance.
Due to the fact that septic tanks are often constructed many yards below and even the lids are just a few feet deep, locating and reaching the tank lid may be a time-consuming and difficult task.
The installation of a septic tank riser is a cost-effective solution to this issue.
The Advantages and Disadvantages of a Septic Tank Riser The world is not full of rainbows and butterflies.

Septic tank risers are built of sturdy materials that protect the septic tank lid from the weather. They are installed on the outside of the tank. A septic tank riser not only makes the placement of your septic tank lid evident, but it also protects your septic tank against unintentional pressure buildup. It’s easy to lose track of where the septic tank is and end up parking your car over it or dumping heavy equipment on it, which is dangerous. In addition, homeowners may be concerned about the expense of installing a new septic tankriser, but it should be emphasized that installation is straightforward and inexpensive. In addition, the expense is insignificant when compared to the long-term savings. With a septic tank riser, you will save both time and money during future septic system maintenance because your septic service provider will be able to find the tank and perform the necessary repairs more quickly
And The problem of aesthetics is also a source of concern for many homeowners. The fact that you do not want a pipe protruding from your property is totally understandable. If aesthetics are important to you, inform your septic tank riser installation professional so that they can ensure that the riser is installed such that the top of the riser is a few inches below the ground surface. By doing so, you may cover the surface with a thin layer of dirt and grass.

These sturdy risers for septic tanks protect the septic tank lid from the weather and are designed to last for years. Septic tank risers safeguard your septic tank against unintentional pressure buildup by making the location of the septic tank lid evident. It’s easy to lose track of where the septic tank is and end up parking your car over it or dumping heavy equipment on it, which can cause serious problems. It is understandable that homeowners may be concerned about the expense of installing a septic tank riser; nevertheless, it should be highlighted that installation is quick and simple.

By installing a septic tank riser, you will be able to save both time and money on future septic system maintenance since your septic service provider will be able to simply find and perform the work; The problem of aesthetics is also a source of worry for many homebuyers.

When it comes to aesthetics, be sure to tell your septic tank riser installation professional so that they can ensure that the riser is installed such that its top is a few inches below ground level. Using this method, you may cover the top with a thin layer of dirt and grass.

Installing Access Hatches

Each and every septic tank is equipped with a cover, however tanks are nearly always placed below ground level. For pump-outs and inspections, you used to have to dig down into the dirt to reach the access hatches of your tank, which was a time-consuming process that many people put off. The inconvenience of this work is one of the reasons why people don’t get pump-outs done on a regular basis. The process of locating the tank, taking out dirt from above the hatches, and then replenishing the soil and re-establishing grass is simply too time-consuming.

There are a few of options for accomplishing this.
After passing through the riser, the tank is reached, where there may or may not be a second cover over the tank body itself.
It is normally possible to retrofit risers and ground-level covers into a plastic septic tank that does not have them originally utilizing hardware from the tank manufacturer.
Riser systems for concrete septic tanks are not often included with the tank when it leaves the manufacturer, but they can be constructed by the homeowner if they wish to avoid digging down to their septic tank in the future.
My initial set of risers and lids were built of pressure-treated timber, but they rotted away after only ten years of use.
Wood is a fantastic alternative as long as you use wood that is guaranteed not to decay under any conditions whatsoever.
The majority of the time, this is how access hatches for septic tanks are constructed at home.
Photograph courtesy of Steve Maxwell As a result, I’ve replaced the old rotted wood with concrete risers that I put in place on top of the tank, with a patio slab serving as a cover on top of that.
If you have any prior expertise mixing and pouring concrete, I strongly advise you to go with this choice.

Concrete risers not only make entry to the tank quick and easy, but they also prevent roots from penetrating your tank via the lids. No amount of effort can penetrate the barrier between the concrete riser and the top of the tank. This is true even for the eager roots of deciduous trees.

VIDEO 7: How to Make Concrete Tank Risers

Tank risers are extensions of the tank lids that are already in place. They are installed in lieu of the current tank lids, bringing the septic tank’s access ports to, or slightly below, ground level in the process. Advantages of Using a Tank Riser

There is no need for time-consuming and expensive excavating
There is easy access to the tank
There is rapid access for emergency pumping
There is regular maintenance

Tank risers practically remove the need for excavating to expose the tank lids for pumping, which saves time and money. If the Alpha Omega is equipped with tank risers, it can readily pump the majority of tanks in less than an hour. In addition, in an emergency situation, the tank may be accessed swiftly and without interruption. Finally, because of the simplicity with which tank risers may be accessed, they encourage frequent maintenance. Alpha Omega suggests that two tank risers be installed on each septic tank, one on each lid, according to the manufacturer.

Regular septic tank lids, which do not extend above the level of the earth, must be buried at least six inches below the surface of the ground in order to prevent gases from leaking out.
We provide risers with a diameter of twenty-four inches to allow for the tank to be maintained correctly and thoroughly in the most effective manner possible.
They are made of a high-quality plastic that has been treated with UV protection.

Septic Riser & Lid Repair Statesville

Sewage Tank Risers and Lids or Lids are intended to be used in conjunction with existing concrete, fiberglass, or metal septic tank covers. Septic Risers are meant to raise the level of a septic tank’s below-grade opening to the same level as or higher than the surrounding ground. Risers are frequently absent from typical septic tanks, particularly in earlier types, and are thus difficult to find. The diameter of risers typically ranges from 8 to 24 inches. Septic tank riser installation services are provided by Lentz Wastewater Inc.

The aperture of the riser is protected by a tight-fitting lid.

Do I Need a Septic Tank Riser?

A septic tank riser system is an extremely beneficial addition to your septic system and is highly suggested by experts. This device will make the process of maintaining and monitoring your septic system more easier, more convenient, and less expensive. Septic tank risers that have been authorized by the state of North Carolina must be put on any new or updated septic system in the state. Your septic system is one of the most expensive mechanical elements on your property.

It is also one of the most complicated. It is also one of the least watched and least understood systems that you have in your possession, as well. If you don’t have septic tank risers, your system will be “out of sight and out of mind” for a long time.

Advantages of Septic Tank Risers

Rising and covering septic tanks in the modern day are significantly more aesthetically pleasing and mix in with their environment
The lightweight septic cover makes it simple to get access to the septic tank. The contemporary covers are lightweight, weighing less than 10 pounds, which makes maintaining your tank considerably simpler. The old-fashioned concrete septic tank riser rings are quite heavy, weighing hundreds of pounds. The concrete coverings are similarly heavy, weighing between 60 and 80 pounds. Many individuals are deterred from lifting the cover and doing an inspection because of the weight of the object. Septic tank riser rings made of modern polyethylene are often less than 30 pounds in weight. Septic tank risers also have the advantage of making it considerably easier to prevent surface water from entering the tank. In the olden days, concrete riser rings were not equipped with a gasket. As a result, surface water may readily flow between the connection between the tank and the riser ring, as well as between the lid and the riser ring, when the tank is filled with water. Nowadays, a watertight seal is installed between the septic tank and the base flange of the riser. The riser rings and covers are also equipped with a long-lasting closed-cell foam gasket to keep the junction between them from becoming leaky. To keep little children from curiously messing with the cover and putting themselves in danger of falling into the septic tank, modern riser covers are fastened with threaded screws.

Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover. Our septic tank risers and covers are constructed of high-quality, heavy-duty polyethylene plastic, which allows them to be both extremely robust and durable while still being lightweight and simple to handle and transport.

Damaged Septic Tank Cover?

In the event that you drive over your septic tank, which is not suggested at all, the cover or lid may be damaged. Lentz Wastewater fixed septic riser covers that were broken, damaged, or mi ssing.

Septic Tank Risers, Lids and Covers in Farmington, NH

It is critical to have properly constructed and maintained septic tank risers in Farmington, Strafford County, Belknap County, Rockingham County, and Carroll County, New Hampshire, in order to adequately service your septic system. More significantly, though, being familiar with your tank’s riser and lid will enable you to be more conscious of the tank’s subsurface presence. If you are unable to identify your riser, require a new riser to be placed, or are experiencing problems with your existing system that necessitate the intervention of a skilled expert, contactB.H.

Risers

If you are doing any type of construction, site grading, or landscaping, it is quite likely that the inlet or service port to your septic tank will be buried eighteen inches or more below the grade of your grass. In New Hampshire, the law states that you can’t dig more than 6 inches below the surface of the earth. A riser is an extension that is made to the entrance of your septic tank in order for your lid to be able to be put on the ground level. Simple acts such as the installation of an appropriately sized riser result in significant savings each time your tank is pumped since you will not be charged for the time spent digging off your tank lid by our crew when we pump your tank.

Having each offers its own set of advantages.

Lids (Covers)

Septic tank lids in Farmington, New Hampshire are used to allow access to your tank for cleaning purposes. They also serve to keep uninvited guests from accidentally entering the tank. You, your family, pets, and animals may be at risk if your lid has been degraded or broken. We keep a large inventory of plastic and concrete lids in store to satisfy the individual demands of your tank or tank system. Immediately contact us if your lid has broken and we will replace it with a new one that will be installed properly by our team of professionals.

For more information on risers and lids, septic pumping services, grease trap maintenance, or to have these critical components of your septic system handled, please contact us at 603-755-2110 now.