How To Fix Clogged Sink If You Have Septic Tank? (Solution)

Lots and lots of bubbles that have the power to loosen and clear away most clogs. Pour half a box (or about 1 cup) of baking soda followed by a half cup of white vinegar down the affected drain. Stop up the drain and wait half an hour before flushing with hot (or boiling) water.

How do you unclog a sink with a septic tank?

Baking Soda and Vinegar Dump a couple of teaspoons of baking soda into your clogged drain, followed by one half cup of vinegar. This will create a fizzing action that may cause a fizz-like eruption. This is normal. This fizzing action may help to break the clog up and get things moving in your drain once again.

What Clog Remover is safe for septic tanks?

All Drano products are septic safe, and Drano Max Build-Up Remover is designed to be used on a monthly basis to replenish your septic system’s bacteria. Like septic safe Drano products, all Liquid Plumr products are safe for use with septic systems and will not upset the balance of bacteria in your tank.

Can you put Drano down a sink with a septic tank?

Will Drano^® products harm my septic system? No, all Drano^® products are septic safe drain cleaners and will not upset the bacterial action in septic systems. Use Drano^® Max Build-Up Remover on a monthly basis to replenish the bacteria in the septic system that help break down toilet paper and organic matter in pipes.

Can you use drain Unblocker with a septic tank?

One of the most powerful chemicals in any household is drain cleaner. Liquid drain cleaners are typically safe for septic systems, but you should check the label and/or the Internet to be sure. Foaming or solid drain cleaners can disable your septic tank and will probably cause damage.

Can you use baking soda and vinegar with a septic tank?

Will baking soda hurt a septic system? Baking soda and other common household solutions such as vinegar are not harmful to your septic system. Harsh chemicals such as bleach and ammonia can disrupt the good bacteria in your septic tank and should not be used as part of a septic treatment.

How do you unclog a main septic tank?

How to clear a main sewer line clog

Step 1: Loosen the cap on the drain pipe. Loosen the cap on the drain pipe.

Step 3: Feed the auger cable into the drain pipe.
Step 4: Run the auger until the clog is clear—and beyond.
Step 5: Hose down the pipe and auger cable.

Step 6: Slowly pull the auger back out of the pipe.

What is the best homemade drain cleaner?

Mix 1/2 cup baking soda with 1/4 cup table salt and pour down the drain giving you trouble. Follow by pouring 1 cup of heated vinegar down the drain (it will foam and bubble). Cover the drain with a plug or duct tape to prevent the mixture from escaping. Let it sit for 15 minutes.

What is a natural drain deodorizer?

Step 1: Mix 1/2 cup baking soda with 1/4 cup table salt. Step 2: Pour the mixture down the drain. Step 3: Pour 1 cup heated vinegar down your drain; the concoction is going to foam and bubble. Step 4: Let the solution stand for 15 minutes (longer does not work any better).

Is Liquid Plumr bad for septic tanks?

Yes. It’s safe to use Liquid-Plumr^® products if you have a septic system. The ingredients degrade rapidly and will not harm the bacteria in your tank.

Can you use bleach with a septic tank?

You might consider bleach to be a great cleaner to use for your septic system. Unfortunately, that mindset is a dangerous one to have because it’s usually recommended to avoid using bleach in your septic system. The chemicals within bleach can kill the bacteria that your septic tank relies on.

Is it safe to pour boiling water down the drain?

Do NOT pour boiling water down your sink or toilet. This can melt PVC piping and pipe seals, causing serious damage. In addition, using boiling water to clear a clogged toilet can melt the wax ring around the toilet, or even crack the porcelain bowl, leading to a pricey trip to your favorite hardware store.

How bad is Drano for septic?

When it comes to your septic system, this chemical combination is devastating for the bacterial environment, with as little as 0.4 ounces being enough to destroy the bacteria in your septic tank.

How do you dissolve sludge in a septic tank?

How to Reduce Sludge in a Septic Tank Without Pumping

Install an aeration system with diffused air in your septic tank.

Break up any compacted sludge.
Add a bio-activator or microbe blend.
Maintain the aeration system.

Add additional Microbes as required.

How do I know if my septic line is clogged?

Signs of Septic System Clogging: Water and sewage from toilets, drains and sinks backing up into your home. Bathtubs, showers, and sinks draining slowly. Gurgling sounds present in the plumbing system. Bad odors coming from the septic tank or drain field.

Septic-Safe Methods for Unclogging a Drain

A clogged drain is a source of frustration for any homeowner, but when a clogged drain occurs in a home with a septic system, one of the most pressing concerns is how to clear the drain without causing damage to the septic system itself. Many homeowners’ first instinct is to grab for a chemical drain cleaner, but if you have a septic system, these harsh chemicals should be the very last thing you use to unclog a drain to avoid damaging it. Drain unclogging procedures that are safe for septic systems are discussed in this section.

Why Chemical Drain Cleaners are Bad for Septic Systems

Despite the fact that chemical drain cleaners are appealing, they are a poor choice for unclogging clogged drains in houses that have septic systems, according to the American Chemical Society. The principle behind chemical drain cleaners is straightforward: send harsh chemicals down the drain, and the clog will be eaten away by the chemicals until it is tiny enough to flow through the pipes. The chemicals are physically melting the blockage away from the pipes. Chemical drain cleaners are among the household cleaners that are prohibited from being used with septic systems due to the presence of sodium hydroxide, sometimes known as lye, in one of its essential constituents.

All of these chemicals are not only detrimental to the bacterial environment of the septic system, but they are also very corrosive and will eat away at the tank’s structural integrity as well.

Septic-Safe Method1: Unclogging a Drain with Boiling Water

Sometimes the most straightforward option is the most effective. Small blockages in pipes may frequently be cleaned by gently pouring boiling water down the drain, which is quite effective. This approach is very effective for unclogging obstructions produced by oil, soap, or even tiny clumps of human hair. It is essential that the water is boiling for this procedure to be effective – not just hot, but boiling hot. This strategy, on the other hand, necessitates considerable caution. It is possible that pouring hot water upon a porcelain sink will result in the sink cracking.

Boiling water has the additional effect of softening the joints in PVC pipes, and as a result, we do not advocate using this procedure with PVC pipes.

Septic-Safe Method2: Unclogging a Drain with VinegarBaking Soda

As children, we used to make volcanoes out of baking soda, vinegar, and red food coloring, which we could see exploding from the ground. As adults, the same experiment (without the red food dye) may be used to unclog a clogged drain without causing damage to the septic system. Whenever baking soda and vinegar are mixed together, a chemical reaction happens, resulting in the formation of carbonic acid, which rapidly decomposes to produce carbon dioxide gas. As a result, what happened? Numerous bubbles with the ability to loosen and clear away the majority of obstructions are released into the air.

Repeat this process twice more. Close the drain and wait half an hour before flushing with hot (or boiling) water to clear the blockage. In addition to being septic-safe, this tried-and-true method of unclogging a drain is also totally safe for the plumbing inside your home.

Septic-Safe Method3: Unclogging a Drain Manually

After trying the first two techniques of cleaning a blocked drain and failing miserably, it may be necessary to don some dishwashing gloves and personally remove the obstruction. Carefully dislodge the clog with a plunger, a plastic drain cleaning tool, or a heavy-duty plumber’s snake to either loosen it enough to allow it to flow through the home’s plumbing or completely remove it from the pipes. The following methods should only be used as a last option, prior to hiring a plumber, and you must exercise caution to ensure that you do not mistakenly harm the afflicted drains by driving a snake into or out of the plumbing system.

Drain Maintenance

One effective method of dealing with blocked drains is to assist in preventing them from occurring in the first place. Fats, oils, and greases, which are responsible for a large number of kitchen drain blockages, should never be thrown down the drain. The fact that hair is the most prevalent cause of bathroom blockages suggests that using protective screens that prevent hair from entering the drain is a smart idea. A clogged drain that does not clear using these septic-safe procedures may indicate that your septic system is in need of repair or replacement.

To book a service visit, please contact us right away.

How Do You Unclog a Drain if You Have a Septic System?

A blockage in your drain may cause water to not drain as efficiently as it should. Most of the time, when this happens, you buy a bottle of chemical drain cleaner and pour some of it down the drain. The chemicals work their way through the clog, enabling water to flow freely through the drain once more. Chemical drain cleaners, on the other hand, should not be utilized if you have a septic system. In addition to killing beneficial enzymes and bacteria in your tank that aid in waste breakdown, chemical drain cleaners can also be harmful to the tank itself, causing it to rupture.

The simplest approach of trying to unclog a clogged drain is to just pour hot water down the drain until the obstruction is removed.
The hot water will help to release any oil or soap that is creating the blockage, and the rush of water will aid to loosen any hair clogs that have formed in the drain.

If hot water does not work, the next approach you may try is a combination of baking soda and vinegar, which should be effective.
This will induce a fizzing activity, which may result in a fizz-like explosion as a result.
In certain cases, the fizzing motion might assist to break up the blockage and get things moving in your drain once more.

In contrast to conventional drain cleaner, septic-safe drain cleaner does not include the potentially dangerous compounds found in regular drain cleaner.

Make certain, however, that the item you are using does mention that it is safe for septic systems. A septic-safe drain cleaning product should always be kept on hand in the event that your home is equipped with one. If all other procedures fail, you can use this approach to unclog your drains.

Clogged Drain or Clogged Septic Tank?

Robs Septicon is the author of this piece. Postings under Uncategorised A blocked septic tank can cause difficulties that are quite similar to those caused by a clogged drain. Knowing the difference between the two might assist you in taking care of your house. Here’s all you need to know about the situation. When a septic tank overflows, why do drains become clogged? The septic tank is a holding tank that is located underground. All of the wastewater from the house flows into the septic tank, which steadily fills up with garbage over time.

Towards the top of the tank, there is a pipe that flows into the yard, into an area known as the drain field, where the tank is located.

The dirt filters the water and kills the bacteria that are there.
It is possible for the septic tank to fill up without any water draining out if the line feeding into the drain field becomes plugged.
As the water rises via the main line, the capacity of fixtures in the house to drain correctly diminishes.

The drains will become sluggish if the septic tank is just half blocked, as the water strains to make its way down into the septic tank.
What Are the Signs of a Septic Tank Clog?
It might be difficult to detect the difference at times.

Due to the fact that they are the most closely associated with the septic tank, the lower drains in the home will be affected first when the septic tank overflows.

In addition to being more sluggish, they may begin to produce unusual noises, such as gurgling sounds, as they age.

Local clogs often only impact a single fixture or a small number of fixtures that are linked to it.

If all of the other fixtures in the house are operating properly, this is an indicator that there is a blockage in the house rather than in the septic tank itself.

A blockage in a septic tank should not be repaired by someone who has just rudimentary expertise or who lacks the necessary instruments.

In certain cases, you may be able to address the problem yourself if you suspect that the blockage is in the pipe rather than in the septic tank.

Allow for an hour or two for the mixture to settle in the pipe before using it.

Depending on how large the blockage is, this may be sufficient to empty the pipe.

An auger is made out of a long, rigid cable with a pointed, twisting end at the other end.

A plumber may be required if neither of these approaches proves effective in clearing the clog from the drain.

Chemical drain cleaners have the potential to harm beneficial microorganisms in your septic tank, which might lead to another clog in the future.

Clogs in septic tanks can arise for a number of different causes.

Many septic tanks require pumping every three to five years, depending on the size of the tank.

Exactly What Should You Do If You Suspect You Have a Septic Tank Issue?

An inspection by a septic tank firm will allow them to determine whether or not the tank needs to be drained.

Rob’s Septic Tanks, Inc. can provide you with further information on clogs and septic tanks. We’ll be pleased to answer any questions you have and provide you with further information.

SEPTIC PROBLEMS THAT CAN MIMIC DRAIN CLOGS

Your bathroom drains may be running slowly, and you may be thinking pouring some chemical drain cleaner down the drain to clear the clog. However, in these situations, rather than relying on potentially harmful drugs, it is always preferable to consult with medical specialists for a diagnosis. Instead of a simple clogged drain, you may be dealing with a plumbing vent problem, a sewer line problem, or a septic system problem instead. Learn about three septic issues that might manifest themselves in ways that are similar to drain obstructions.

An entrance baffle and an output baffle are standard features of a septic tank.
The intake baffle assists in the smooth entry of wastewater into the tank.

This form of obstruction, like a drain clog, will cause drains to slow down or stop completely.
2.
In addition, there is the pipe that runs from your house to the septic system.

In addition to blockages, this main line is subject to earthquake damage, damage from huge machinery being driven over the region, and tree root damage, no matter what material it is constructed of.
Failure of the Drainfield It is possible that some homeowners are unaware that septic systems have a limited lifespan.

For this reason, you must have a reserve leach field site set aside when installing your sewer system, as mandated by federal laws.

One occurs when a large amount of solid waste is introduced into your system, causing them to get clogged to the point where they must be replaced.

Compaction is another issue that can cause a leach field to fail prematurely if it is not addressed.

Due to the fact that the field’s functioning is dependent in part on bacteria that require air in the soil to survive, this might render the region unusable.

Some of the symptoms of these three septic illnesses might be mistaken for those of a normal plugged drain in some cases.

Consequently, if you feel your drains are slowing down, get a professional to come out and take care of the problem.

Contact Upstate Septic Tank, LLC as soon as possible if you are in need of a diagnostic visit, sewer line cleaning, or a septic system cleaning and pumping. We’ll be pleased to assist you in keeping your septic system in the best possible condition.

How to Clear a Clogged Septic Line

If you have ever had to deal with a clogged drain, you are aware that the cleanup procedure is anything but enjoyable. Sewage line blockages are often caused by an obstruction in the pipes or when the septic pipe levels out and prevents gravity from conducting its work.

Symptoms of a Clogged Drain

In virtually all cases, when you have a clogged drain or pipe, you will feel at least one of two symptoms. An foul odor emanating from the sink, toilet, drain, or other plumbing fixture almost always indicates the presence of something as unpleasant impeding the course through the pipes. In sinks, it is almost always food that is the source of congestion. In toilets, it’s possible that someone flushed something they shouldn’t have, or that they truly emptied and should have used a mid-session flush instead of the first flush.

2. Water Going the Wrong Way

Water is intended to wash down the drain and not come back up, so it makes sense that it would. Some obstruction is causing your sink or shower to take an excessive amount of time to train. Even though a blocked line is typically caused by anything that has been flushed down the toilet, the source of the problem may be located deep inside the heart (and pipes) of the septic system itself. It is possible that tree roots are causing your septic system to back up. Obviously, if this is the case, you’ll want to consult with a specialist right away.

It is possible for your pipes to freeze during the winter months if they are not buried at the right depth.

Tips for Clearing a Clogged Drain

Before you call a septic company, there are a few things you may do to try to unclog your drain on your own that may be successful.

1. Avoid cleaners with chemicals

Chemical-laden cleansers have a tendency to degrade the enzymes in your septic system, which are designed to aid in the degradation of waste. Instead, use a drain cleaner that is suitable for septic systems and does not include any harsh chemicals. A professional cleaner should always be kept on call in the event of an emergency.

2. Pour hot water down the drain.

The surge of hot water, particularly in kitchen sinks, is typically sufficient to dislodge or dissolve any clog in the pipes. Check to see whether boiling water might be of assistance before seeking expert assistance.

3. Use baking soda and vinegar.

If water alone is ineffective in dissolving the obstruction, a baking soda and vinegar reaction may be used to achieve success. Pour a couple spoonfuls of baking soda down the drain, followed by a cup of vinegar, then flush the toilet. The fizzy explosion aids in the breakdown of waste and the restoration of normal flow. The fact that you are unable to unblock the blocked drain by yourself might indicate that the problem has reached a deeper level. An impediment other than food might be blocking one or more septic system pipes, which could be collapsing.

Septic systems are something we are very familiar with, and we can handle just about any septic problem, including a clogged drain or septic line, thanks to our 40 years of experience. If you have any reason to believe that there is an issue with your system, please contact us.

who should you call for septic issues?

Septic tank cleaning and septic tank pumping services are provided by Norway Septic Inc., a service-oriented company devoted to delivering outstanding septic tank cleaning and septic tank pumping services to households and business owners throughout the Michiana area. “We take great delight in finishing the task that others have left unfinished.” “They pump, we clean!” says our company’s motto. If you believe that your septic system is having troubles, or if you require septic replacement components such as septic filters, please contact us right once.

Our affiliate connections to these items generate a small profit for us if you decide to purchase them via our links.

How to Unclog a Drain and Septic Tank : Tips and Tricks

Plumbing

Unclogging
Septic Tank
Blocked

Septic System
Pipes and Drains
How to Plumbing

A few methods for unclogging a septic tank drain, as well as suggestions for speeding up a slow drain, difficulties that may arise while unclogging a drain, and preventative steps to avoid blocked septic tanks and drains will be discussed in this article. As well as how to unclog a septic tank and strategies to handle typical septic problems that may arise as a consequence of a full septic tank or clogged septic lines, this article will teach you how to unclog a septic tank. Your kitchen sink drain or bathtub drain is attached to a specific branch line and drains at a slower rate than usual because of this.

Reasons for a clogged bath or kitchen drain:

Dumping food or solid stuff down the drains is prohibited. Putting oil or other sticky substances into the kitchen sink

Dumping chemicals or paints down the drains is not acceptable. Hair down the drains of the bathtub and shower
Ventilation that is improper and/or insufficient Drainage system that is clogged Septic intake or outlet that is clogged

Common Causes of Clogged Drains

Many various things may cause your kitchen sink drain or bathroom drains to get clogged, but the most typical reasons of clogged drains are still leftover food and grease from the kitchen that is poured down the kitchen sink, as well as hair that is flushed down the bathtub and shower drain. Another typical reason of clogged drains is the buildup of paints and other chemicals inside the drain pipe, which solidify and block the line. In many cases, you will be able to unclog a blocked kitchen sink or a clogged bathtub drain on your own.

Ways to unclog a drain:

Baking soda and vinegar drain unclogging is an alternate and more natural method of unclogging a clog in the drain. Vinegar and baking soda have no negative impact on the environment. A plunger can be used to clear a clogged drain. This method will work for clogs of modest size and will not cost you much money. If the obstruction continues, consult with a professional. Although it is more expensive, unclogging a drain with a cable or auger may be quite successful in removing solid obstructions in the drain and even breaking through thick roots
Yet, it is also more efficient. Pouring paint or other sticky and oily materials down the drain can produce blockages, and high-pressure water jetting is more successful at clearing them.

Before you begin utilizing high-pressure water jetting to unclog your drain, be sure that your pipes are capable of withstanding the high pressure that will be applied by the high-pressure jet. Otherwise, the high pressure will rip your pipes apart. Hydro jetting is best left to the professionals, such as your local plumbers.

Ways to avoid clogged drains and a full septic tank:

Avoid blocking your sink drain by pouring solid objects or oily stuff down it. Cover the drains in your toilet and kitchen with filters to protect hair and solid things from entering the drain system. Make certain that suitable numbers of air vents are provided, and that the diameters of the vents are acceptable for all of your fixtures.

Problem II: All of your home’s drainage lines are sluggish to drain, and the drain water from the main drainage line is backed up in a pool.

Possible causes for a slow drain:

An obstruction has formed in a section of the main drain line

An obstruction has formed at the drain intake or outflow of the septic tank. A section of the percolation pipes has become jammed
The septic tank vent has become obstructed. Low temperatures have caused the sewage tank or septic vents to become iced over
One of the distribution boxes has been blocked off

Ways to unclog a main drain or full septic tank:

To unclog the main drain line, use a snake or high-pressure water jetting. This is the work of a professional. By virtue of his knowledge and experience, he can snake a sluggish drain, determine if the blockage is caused by solid waste, oily substances, or roots, and apply the most appropriate procedure to unclog the drain. Verify that there is no blockage at the entrance or exit of the septic tank owing to solid wastes or scum, among other things. Check the distribution box, which is placed between the septic tank and the percolators, for easy flow once the block has been removed. If there are any obstacles, they should be removed. Check the region around the percolators for any problems. Check to see whether the area is damp, marshy, or smelly. It indicates that the percolation process is not working properly. Another type of work is where the earth is not absorbing the drain water at the same pace as it is being discharged. It might be because your water use has increased recently as a result of the increased number of guests, or it could be because the soil has been saturated as a result of moisture from other sources such as rainfall (which has been above average), or both. If your septic tank has frozen due to inclement weather, call an expert right away
If your septic tank has frozen due to inclement weather, call an expert right away. Use the septic tank as a storage tank until the tank has completely thawed on its own if you can’t find a professional or the tools you need to do the job. You will be able to hang on for a longer period of time if you make wise use of water. Winterizing the septic tank before the following winter will help to prevent it from freezing in the future.

Preventive measures to avoid a blocked main or slow drain:

Please be considerate of your septic tank. It is intended solely for the disposal of organic waste materials. Avoid dumping non-biodegradable and inorganic wastes in landfills. They will almost certainly overflow a septic tank and interfere with the normal operation of the septic tank. Use drain filters in your toilet and kitchen to catch hair and solid objects that are flowing down the drain. In order to prevent the septic tank from freezing in the winter, it should be winterized. If you are planning a long trip, you should empty your septic tank and seek professional assistance. Winterization is dependent on the area and weather conditions. A small investment here will save you from all of the difficulties you will face during the winter.

External References

Natural ways to unclog a drain include the use of vinegar, baking soda, and water (theGoodHuman.com), among others. On eHow.com, you can learn how to unclog a sink naturally.

Documentation Download Documentation Download Documentation In the event that you have slow drains, pooling water in your yard, or foul aromas near your septic system, it is possible that one of the pipes has become clogged. Fortunately, there are several methods for removing blockages from your sewage system that do not require the services of a septic service specialist. To begin, search for any apparent obstructions inside your septic tank and try if you can drive them out with a little force.

If you need to get to a clog that is further inside a pipe, you might want to consider utilizing a mechanical auger to cut through it. Following the removal of the blockage, be sure to properly maintain the septic system in order to keep it clean!

1 Check the inflow pipe by lifting the access cover of the tank that is nearest to your residence. The plastic or concrete cover in your yard that is closest to your house should be the first place you look. Carefully raise the cover of the tank up and away from the tank so that you can see what’s within. If you notice a white or green pipe at the end of the tank closest to your home, look for anything that could be blocking the pipe’s outlet. If there is, it is possible that the blockage is the source of the problem.

Assuming the water level is below the level of the entrance pipe, the blockage might be located in the drain pipe that runs between the septic tank and your residence. If the water level is higher than the inlet but there is nothing blocking the end of the pipe, the clog is most likely in the leach field
However, this is not always the case. It may be necessary to dig up the access lid with a shovel or raise it with a pry bar in order to get access.

Advice: If you are unable to locate the access lid for your septic system, consult with your home’s as-built plans, which are blueprints prepared after your home is constructed, or with a professional septic service. 2 If the scum is trapped at the end of the input pipe, use a pole or a stick to push it out of the way. The scum layer is composed of solid waste that accumulates on the surface of the septic tank. Make use of a long, strong piece of wood or metal to slide the scum down or to the side of the entrance pipe as needed. Continue to remove as much scum as you can from the area around the pipe so that it can continue to fill your tank.

If you are working in your septic tank, you should always wear gloves to prevent bacteria and waste from getting on your hands. If water starts to flow out of the pipe after you’ve pushed the scum out of the way, you’ve successfully eliminated the clog.

s3 If the blockage is deeper inside the pipe, use the pole or stick to probe the end of the pipe. Insert the end of the stick or pole you’re using as far as it will go into the end of the pipe you’re working with. Make use of the end of your probe to scrape the edges of the pipe and draw any waste from the pipe into the tank. Even if the clog is at the very end of the pipe, you should be able to dislodge it and get the water flowing once again. It is likely that the clog is located deeper inside the pipe if water does not flow out of it.

Depending on where the pipe is located, you may or may not be able to insert your probe into the pipe.

4 Disinfect any instruments you used by mixing a 5:1 solution of water and bleach together. Stir up 1 part chlorine bleach and 5 parts clean water in a big bucket until the chlorine bleach is completely dissolved. Immerse your tools in the solution and allow them to soak for around 5 minutes to destroy any germs that may have remained on the surface. When you’re finished, drain the liquid back into your septic tank.

If at all possible, take a shower or bath as soon as possible after working on your septic tank
When you wash your garments, use bleach or laundry sanitizer to ensure that no bacteria is left on them after washing.

5 If you were able to resolve the issue, replace the access lid on the septic tank. Lift the lid and place it over the opening that leads into the septic tank to prevent it from closing. Slowly drop the lid down until it fully covers the hole and does not move around any more. Continue to leave the lid open in order to insert a mechanical auger if you haven’t removed the blockage.

Never leave the septic tank door open while you aren’t working on it to prevent anything from falling into the tank.

6 Make use of a reputable service. If your tank was completely filled, you should pump it within 5 days. It is conceivable that your tank will back up again even after you have removed the clog. This is especially true if your main tank is completely full to the entrance line. Inform septic service personnel that the scum level has reached the pipe by contacting them through telephone or email. It is best to schedule them within the following 5 days, otherwise you will increase the likelihood of septic fluid returning up the drainpipes. The service will drain your septic tank, ensuring that scum does not re-enter your plumbing system.

Having a septic tank pumped typically costs between $75 and $200 USD, depending on the size of the tank and the amount of waste that has to be removed. Every 3–5 years, or whenever the tank becomes full, have your septic tank cleaned and emptied.

In order to get to the inflow line, you must first remove the septic tank access lid that is closest to your residence. Because the intake pipe is more likely to be located on the access lid nearest to your home, if your septic tank has multiple access lids, select the one that is closest to your home. Using your hands, lift or pull the tank’s cover off and set it aside while you continue to work. Inside your tank, look for the end of a white or green pipe that protrudes from the side that is closest to your house.

If you are unsure about the location of your tank’s access lids, consult your home’s as-built plans or consult a professional service.

2 Insert the cutting blade of a mechanical auger into the jammed pipe’s end with the auger’s handle. A mechanical auger is comprised of a long metal cable that is inserted into your pipes and equipped with a revolving bit that cuts through the obstruction. Begin at the end of the blocked pipe or at an access point for the pipe, such as a cleanout port, to unclog the blockage. Placing the cutting blade of the auger inside the obstructed pipe and pushing the line in around 1–2 feet (30–61 cm) can clear the blockage.

It is possible to purchase a mechanical auger either online or from a local hardware shop. Investigate whether your local hardware shop provides equipment rentals to see if you can borrow an auger for the day without having to pay the whole price

3 Before you turn on the auger, make sure you have on your safety glasses and work gloves. Because mechanical augers feature spinning and moving elements, it is important to wear eye protection to avoid injuring yourself if you lose control of the machine while working. Wearing heavy-duty work gloves can help you prevent spreading germs and being harmed when handling the line. The auger should be connected to the nearest electrical outlet and the switch should be in the On or Forward position.

It’s possible that you’ll require an extension cord to connect the mechanical auger. You should never use the auger without wearing gloves or wearing safety eyewear since you might suffer a serious injury. Because the auger would spin violently if you start it with the cutting end outside of the pipe, you should never do so.

4) Continue to feed the auger deeper into the pipe until the obstruction is broken apart. Holding the auger’s line with both hands, guide it into the pipe until you encounter resistance if necessary. Try rotating the line in your hands to see how far it will travel within the pipe if the resistance feels substantial. It is possible that it has encountered a curve in the pipe. To drive the obstruction apart if this is not possible, use short, back and forth strokes to push and pull the auger. Continue to force the auger into the blocked piece of pipe until it is able to pass smoothly through it

If you successfully clear the clog, water will begin to flow through the pipe again while you are still inside it with the auger. Mechanical augers are available in a variety of lengths, so if the one you’re currently using isn’t long enough to reach the blockage, consider renting the next largest size.

Keep at least one hand on the auger’s line while it is operating to ensure that it does not spin or rotate while you are trying to feed it. Before removing the auger from the pipe, be sure it is turned off. Make sure that the auger’s power switch is in the Off or Reverse position so that you can easily remove it from the ground. With both hands, gently guide the auger’s line back into the container, then slowly bring it back through the pipe to the other end. Using a hose or paper towel, carefully remove the auger end out of the pipe and clear off any dirt or trash that has become lodged on the end.

It is not advisable to remove the auger from the pipe while it is still operating since it might cause injury. Remember not to touch the auger’s line with your bare hands because it has just passed through a pipe that contains garbage and potentially deadly bacteria.

6 The tools should be cleaned with a solution made up of 5 parts water and 1 part bleach. Stir the solution together by pouring 1 part chlorine bleach and 5 parts clean water into a bucket and mixing thoroughly. Clean the end of the auger with a cleaning rag to eliminate any germs that may have remained on the surface and avoid contaminating other parts of the machine. You should drain the solution into your septic tank after you’re finished

Don’t flush the cleaning solution down the toilet since it contains bacteria from your septic tank that are dangerous.

7Remove the septic tank’s cover and replace it. Lift the lid off the ground by grabbing it by the handles or the sides of the container. Lift and carefully drop the lid back onto the opening going into your sewage treatment system until it is completely enclosed. Make sure the lid does not slip or shift in any way, or otherwise it may break loose and fall off the septic tank. Advertisement

1 Other than water and natural garbage, avoid dumping anything else down your drains. Water, human waste, and toilet paper are the only things that septic tanks are designed to handle
Thus, any additional products can cause the entire system to get clogged. To avoid clogging pipes, place paper towels, wet wipes, food scraps, and other solid waste in the ordinary garbage instead of in the recycling container. Make it clear to other people in your home what they can and cannot flush down the toilet to avoid clogging the drains and pipes.

Using strong chemical cleansers down your drain is not recommended due to the possibility that they can destroy the natural bacteria in your septic tank that is responsible for decomposition of solid waste. You should never pour cooking oil down the drain because it might harden in the pipes and cause blockages that are difficult to clear.

As a reminder, you do not need to add any additional natural enzymes or bacteria to your septic tank in order for it to properly break down solid waste. Any additional enzymes will be ineffective in comparison to the enzymes that naturally present in the tank
2 Reduce the amount of water you use in your home so that the septic system can drain correctly. Avoid running water in your home until absolutely necessary, since doing so may cause the tank to fill up too rapidly and overflow. Use as little water as possible when bathing or cleaning, so that you only have as much as is necessary at any one time. In the event that you have any outdated or leaking fixtures, you should repair them or replace them with more energy-efficient systems, such as toilets that flush less water or faucets with aerators.

It will also save you money on your utility bills if you keep your water consumption to a minimum.

3 Avoid driving or planting over the area where your septic tank is located. Heavy weight can cause pipes going from your septic tank to collapse or break, so if at all possible, avoid driving over the region in a vehicle as much as possible. Plant roots can also grow into the pipes or septic tank, causing them to clog more quickly than they otherwise would. Maintain a distance of at least 20–30 feet (6.1–9.1 m) between your septic system and any trees or plants you intend to plant so that the roots are not able to grow within.

Even if you use a mechanical auger to remove the roots out of your pipes, the roots will come back if the problem is not addressed. Root barriers purchased from gardening supply stores destroy roots on touch and can help to prevent overgrowth in your septic system. To protect your septic system from pipes, dig a trench around it that is 2 feet (61 cm) deep and 3 feet (91 cm) away from them. Make sure that you place the root barrier in the trench vertically before you fill the trench back up with earth.

4 Improve drainage by cleaning the effluent filter located on the outflow pipe. The effluent filter is a plastic cylinder that is installed in the exit line of your septic tank to prevent solid waste from escaping. Make sure the tank closest to your home has an access cover that can be opened. Look for a vertical white or green pipe that holds the filter and protrudes through the top layer of scum on the interior of the filter. Remove the filter from the vertical pipe by pulling it straight out and rinsing the waste back into the tank using a hose. Push the filter back into the pipe so that it may continue to prevent waste from escaping

Not every septic system will be equipped with an effluent filter
However, most will. Check your filter every time you have your tank pumped or examined to ensure that it does not become clogged.

5. Have a professional inspection of your septic tank performed once every three years. Septic tanks typically take 3–5 years to fill, however this might vary based on the size of the tank and the quantity of water it receives. Consult with a professional provider to have the water levels and pipes for your system checked to determine if any adjustments are necessary. If the provider has any issues, you should solve them as quickly as possible to avoid having a malfunctioning septic system later on. Advertisement

Create a new question

Question What is the location of your septic tank? David Balkan is a writer who lives in New York City. A professional plumber and the CEO of Balkan Sewer and Water Main David Balkan is a licensed professional plumber who also serves as the CEO of Balkan Sewer and Water Main Service and the President of Balkan Sewer and Drain Cleaning, among other positions. With over 40 years of experience as an active owner of these businesses, David is well-versed in the challenges that arise with water service lines, sewers, and drain lines. David has served on the Executive Committee of the Sub Surface Plumbers Association of New York for more than 30 years and is now the Chairman of the Master Plumbers Council’s Committee on Plumbing. As a result of his expertise and solution-oriented approach, Balkan Sewer and Water Main Service has grown to become the biggest and most trusted sewer and water main service in New York City, and the recipient of the 2017 Angie’s List Super Service Award. Answer from a Professional PlumberCEO of Balkan SewerWater MainExpert Because they have to be pumped out on a regular basis, they usually have clean outs that are visible to the public. The quickest and most straightforward method is to discover your major house trap or clean out. Typically, the first tank would be 15 feet or somewhat more away from the outer wall of your home because it is frequently the very minimum distance that is needed by building codes. Once you’ve identified your primary cleaner or trap, you may utilize the instruments that experts employ. Their electronic pipe tracing equipment may be inserted into your main sewer line, allowing them to find and locate where the tanks are located. Question Is it harmful to my septic tank to use too much Rid X at one time? Using excessive amounts of Rid X will have no negative consequences. Question Is it possible that heavy rains or storms might cause difficulties for my septic system? Daniel and Robin KirbyAnswer from the Community Identifying a concave indention over your field lines or over your septic tank is important if you’re experiencing troubles every time it pours rain. Because of this, water can accumulate directly on top of your field lines, resulting in an overflowing sewer system. To correct it, just fill up the sunken sections with concrete. A short hill in the middle, sloping down to normal grade on both sides of the field line for approximately two feet, may correct this
Nevertheless, Question Is there a natural enzyme, such as dry yeast, that may be utilized instead of paying for expensive enzyme treatments or having a septic system that has only been used by one person pumped out? The man that came to service our septic system had a lot of expertise. He informed me that we could save money by simply adding a package of standard yeast to the mix once or twice a month, rather of buying special yeast. I buy the store brand (which costs 79 cents a packet) and flush a couple of packets every month down the bathroom sink. That is all there is to it. Question What is the best product to use in the toilet to protect my septic system from damage? Daniel as well as Robin Kirby Community Answer Although there is enough of food for your bacteria in a septic tank, it dies due to a lack of oxygen, therefore if you add additional bacteria, they will die practically as soon as they are flushed out with the wastewater. A treatment plant, where oxygen is fed into the tank, may increase the number of bacteria from the millions that exist in a septic tank to billions when both aerobic and anaerobic bacteria can grow! Having said that, treatment plants should be drained out more frequently than septic tanks, according to industry standards. Question In the case of a septic system, what can I use to unclog a clogged sink drain? For myself, I prefer to use a plastic drain snake. It is a plastic ribbon with little barbs that grip anything is obstructing your drain and pulls it out of the way (usually hair). While they are inexpensive and quite effective, they are also a bit dirty
Question When my septic tank becomes clogged with oil and hair bleaching chemicals, what should I do to clear it out? No oil or grease should be flushed down the toilet or into the septic system. Put it in a grease can and toss it out of the window. As far as bleach is concerned, it destroys the microorganisms that your septic system requires in order to function properly. You might wish to look into septic-safe items
They are available.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

Unless you are skilled in septic tank unclogging or there is significant damage to the pipes, you should hire a septic specialist to conduct the necessary repairs for you to guarantee that everything is in compliance with the law. When working on your septic tank, always use protective eyewear and disposable gloves to prevent contamination.

Things You’ll Need

Hose
Paper towel
Mechanical auger
Safety glasses
Work gloves

About This Article

The writers of this page have together authored a page that has been read 314,294 times.

Did this article help you?

That feeling you get after flushing the toilet and nothing comes out is wonderful, isn’t it? It might be amusing to hear your toilet gurgle or to hear the water flowing continually, but it can also be frightening to hear the water level climb as you watch it. It’s an unpleasant situation, not to mention that it necessitates a great deal of hard effort and elbow grease in the process of plunging and cleaning up the subsequent mess. When anything gets stuck in your pipe or your toilet makes a mistake, you may have blockages and backups.

Clogs can form inside your septic tank from time to time, causing blockages in the tank and drainage troubles to arise.
What if we told you that you could fix it yourself?
While bringing in a professional may be required in certain cases, there are several things you may do to resolve the situation without calling for assistance right immediately.
In your search for solutions to unclog your septic tank, you may want to try things like slowly pouring hot water down the drain or pouring vinegar down your drains to break up obstructions, to name a few possibilities.
In order to clear blockages from your drain, you may need to use a professional drain cleaner that you pour down the drain.
However, although these chemical cleaners will eat away at obstructions, they will also kill off beneficial bacteria in your tank, disrupting the delicate bacterial balance in your tank.
Yes, the nasty bacteria will die off, but the healthy bacteria will also die off.

With regard to drain cleaners, the best option is to select one that has concentrated bacteria and enzymes that will eat away at the dangerous bacteria and materials in your tank while simultaneously boosting the amount of helpful bacteria and enzymes in your tank.

In the case of trying to rehabilitate your septic system, using a product such asSeptic Blastcan be really beneficial.

After that, the product will begin to gently eat away at the obstructions in your tank, therefore it’s vital to be patient throughout this process.

It is possible that you may need to repeat this method every day for several days in a succession before the blockage is completely removed.

Your septic tank has now been cleansed and returned to its original level of functionality.

Fortunately, here at Green Gobbler, we provide excellent alternatives to harsh chemicals and maintenance supplies, allowing you to address your problems while minimizing the impact on the environment and your plumbing system. Choose Septic Blast to do the task right away!

What Can Unclog a Drain & Be Safe for the Septic System?

Whenever you have a clogged drain and your home drains into a septic system, it’s critical to utilize a drain cleaner that is suitable for septic systems. Featured image courtesy of Bill Oxford/iStock/Getty Images Whenever you have a clogged drain and your home drains into a septic system, it’s critical to utilize a drain cleaner that is suitable for septic systems. Regular drain cleaners can interact with and destroy the microorganisms in your septic tank, which is why you should avoid them.

The importance of maintaining the right balance in your septic system cannot be overstated.

Drano and Liquid Plumr

When confronted with a clogged drain, the majority of people immediately grab for the chemical drain cleaners. This is not always a smart idea if you have a septic system installed. An effective septic tank is fundamentally a bacterial ecosystem, and maintaining a healthy mix of bacteria is critical to the process of decomposition of organic waste. Septic tank bacteria balance is disrupted mostly as a result of chemical exposure, which includes numerous drain cleaners and other household products.

All Drano products are septic-safe, and Drano Max Build-Up Remover is intended to be used on a monthly basis to replace the bacteria in your septic system’s biological filter.

Natural Drain Cleaners

Using a plunger to attempt to unclog a drain is one of the safest methods of doing so. It is non-invasive and frequently effective in clearing tiny obstructions. The use of a plunger while dealing with a chemical drain cleaner, even if it’s a septic safe drain cleaner, should be avoided at all costs since it can cause the product to splash back on you. Using a plunger is recommended before using a drain cleaner, but it is not required. Many homeowners are adamant about avoiding using a septic-safe Drano or Liquid Plumr solution for a variety of reasons.

An all-natural septic safe drain cleaner that is popular for more significant blockages is a combination of baking soda and vinegar.

Maintenance to Prevent Clogged Drains

You can do some simple maintenance on your septic system to maintain it in good working order and eliminate the need to unclog your drains. This will prevent blockages from accumulating in your pipes. The most straightforward approach to accomplish this is to avoid flushing anything down the drain that might clog a pipe, such as grease and oils. Because hair is a typical source of clogged drains, it’s a good idea to install protective screens over your shower and tub drains to collect any hair that may fall through.

For those who believe they will be unable to function without their disposal, there are various kinds on the market that are safe for use with septic systems.

As a result, regular home items such as bleach and certain soaps and detergents will aid to maintain the essential balance that can be thrown off by these products.

How To Unclog Your Drains At Home?

Drain obstructions are a frequent problem, but they may often be handled without the need for a professional’s assistance. Furthermore, you will not be need to employ dangerous chemicals in order to clean up your blockage. With a little patience and certain tried-and-true procedures, you can frequently unclog your own drain in a relatively short period of time with minimal effort. There may be additional considerations you should take into account when removing clogs from your septic system to ensure that back up does not negatively impact your septic tank or cause problems with septic tank pumping or solid wastes in theseptic tank.

First and foremost, attempt to physically remove whatever is causing the difficulty. Hair accumulated around a pop-up stopper or strainer is one of the most prevalent causes of blockages. You may be able to performdrain cleaning and remove the hair while also clearing thedrain clog, or you may be able to use a drain stick to clear obstructions in thedrain pipe produced by hair in a P-trap or an S-trap, depending on the situation. Sink trap cleaning may remove clogs caused by buildup or a foreign item
A plunger can clear clogs that aren’t too far down the pipes
And a plumbing snake can clear deep blockages
A chemical drain cleaner can break up persistent clogs. Select a product that is appropriate for your system as well as the sort of pipes you have. If you have a septic system, for example, you need make sure the drain cleaner is septic-safe. Drain cleaners should never be mixed, and you should avoid using any drain opening equipment after using a drain cleaner. Because the chemicals in drain cleaners are harsh compounds that can create chemical reactions, it is important not to allow them to come into contact with finished fixtures such as faucets, stoppers, or drain trim. A natural drain cleaner is a less harmful option. Aside from being softer on your pipes and other features, natural drain cleaners are less likely to have a negative impact on the environment than chemical drain cleaners. Natural drain cleaners that use particular enzymes or other septic safe drain cleaners are the most environmentally friendly. Drain Cleaner Made at Home: Pour 12 cup baking soda down the drain, ensuring sure it goes all the way down. Drain a 12 cup white vinegar into the drain and cover the drain with a stopper or a towel immediately to ensure that the bubbles remain in the drain. Remove the cloth or stopper and pour another 12 cup of vinegar into the drain, repeating the process for another 2 minutes. Once you’ve waited 15-30 minutes, flush the drain with a gallon of hot water. If the clog is really tenacious, you may have to repeat the procedure. Grease clogs are particularly susceptible to this treatment, which is why dish soap and hot water should be utilized. All you have to do is pour a generous amount of dish soap down the drain, followed by a pot full of boiling water
Pour a cup of hydrogen peroxide and one spoonful of baking soda down the drain and let it sit for a few minutes. Pour in enough boiling water to create foam, and the chemical reaction will take place, breaking up the blockage and clearing the sink drain/shower drains, kitchen drains, and other drains. Prevention is always preferable to cure. Never pour coffee grounds, grease, or anything else that has the potential to harden or clump down a sink or drain line. Make use of plenty of cold water if you are using a garbage disposal to flush down any food particles. Clean pop-up stoppers and strainers on a regular basis, and consider applying a treatment that is intended to decrease buildup and corrosion in pipework. This will help avoid clogged drains and gurgling, as well as the requirement for a plumber’s snake or auger to be installed.

When You Need a Professional Plumber’s Help

If you are unable to remove a clog, whether it is in your kitchen sink, main line, wastewater line, or anyplace else in your plumbing system, it may be necessary to bring in the pros at A-1 Sewer and Septic Service for assistance. As a family-owned business that has been serving the inhabitants of the Kansas City Metro Area since 1968, we have built a reputation for providing efficient service at competitive, up-front costs. We are accessible on your timetable and may provide same-day and weekend service if necessary.