How To Find A Septic Tank On Acreage? (Question)

Go to your basement or crawl space, and then look for the main sewer line that leads to your septic tank. Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside.

• Clues to Find Your Septic Tank: Look for an unusual mound of earth or a hill which indicated the presence of a septic tank around the property. Look for unusual greenery in any area.

Are septic tank locations public record?

Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.

How do I find out if my land is septic?

A surefire way to confirm whether or not your home has a septic system is to check your property records. It is likely that the building permit and blueprints for your home and property will contain information about the presence (or lack) of a septic tank.

Where are most septic tanks located?

Toe the Line. Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.

Can a metal detector find a septic tank?

If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.

What is OWTS?

An Onsite Wastewater Treatment Systems (OWTS) is a privately owned and maintained sewage disposal system. They are commonly referred to as septic systems. All OWTS have two basic components: a two-compartment septic tank and a disposal field.

Can you have a septic tank without a leach field?

The waste from most septic tanks flows to a soakaway system or a drainage field. If your septic tank doesn’t have a drainage field or soakaway system, the waste water will instead flow through a sealed pipe and empty straight into a ditch or a local water course.

How can I find out if a property is on mains drainage?

One way to find out if your property has surface water drainage is checking your property’s Title Deeds (you can do this through Gov), or looking at your original Planning Application.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

How deep should a septic tank be buried?

In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid.

How often should a septic tank be pumped?

Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.

Can I drive over my leach field?

Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.

How much does a pump for a septic tank cost?

Average Cost To Pump A Septic Tank The national average cost to clean and pump a septic tank is between $295 and $610 with most people spending around $375. Depending on the size of your septic tank, pumping could cost as low as $250 for a 750-gallon tank, or as high as $895 for a 1,250-gallon tank.

Can you use a metal detector to find sewer lines?

Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.

How To Find My Septic Tank

1. What is a septic tank
2. How do I know if I have a septic tank
3. And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
4. What to Do Once You’ve Discovered Your Septic Tank

You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.

“How can I locate my septic tank?” is one of the most often requested inquiries we receive.

When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.

The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.

In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.

How to Locate Your Septic Tank

Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.

What Is a Septic Tank?

Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.

Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.

An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.

Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.

Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.

How Do I Know If I Have a Septic Tank?

What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.

• A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
• A septic system is likely to be installed in your home if you reside in a rather rural location.
• Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
• When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
• Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.

Why It’s Important to Know the Location of Your Septic Tank

You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:

1. To Be Able to Care for It Properly

The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.

2. If You Want to Landscape or Remodel Your Property

If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.

For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.

3. If a Problem With Your Tank Occurs

Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.

4. Ease of Getting It Fixed

Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away

1. Use a Septic Tank Map

First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.

1. If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
2. The county health department is responsible for keeping track of septic systems.
3. A septic tank’s position could be depicted on a survey map, for example.
4. The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.

2. Follow the Pipes to Find Your Septic Tank

Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.

1. In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
2. By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
3. The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
4. Going via the sewage line itself is another method of locating the septic tank utilizing it.
5. Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
6. When the snake comes to a complete halt, it has almost certainly reached the tank.
7. While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
8. When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.

If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.

3. Inspect Your Yard

Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:

• Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
• Directly in front of the home Immediately adjacent to your well (if you have one)
• In close proximity to trees or densely planted regions
• In the shadow of a patio, deck, or other building

Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.

Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.

4. Talk to Your Neighbors

If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.

5. Look for Your Septic Tank Lid

It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.

The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.

What to Do After You Find Your Septic Tank

Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.

However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.

1. Mark Its Location

The likelihood is that you will not want to post a large sign in your yard that reads “Septic Tank Here!” but you will want to leave some sort of marking so that you can quickly locate the tank and lid when you need them. In an ideal situation, the marker will be substantial enough that it will not blow away in the wind and will not be readily moved by children who are playing in the yard. A patio paver, a potted plant, or a decorative gnome or rock are just a few of the possibilities. In addition to putting a physical sign beside the septic tank, you may draw a map or layout of the area around it to illustrate its position.

2. Take Care of Your Septic Tank

Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.

In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.

For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.

Call a Professional Plumber

Maintenance of a septic system is not normally considered a do-it-yourself activity. In the Greater Syracuse region, whether your septic tank requires pumping out or cleaning, or if you want to replace your tank, you should use the services of a reputable plumbing firm to do the job right. If you’ve attempted to locate your septic tank on your own and are still unsure of its position, it may be necessary to enlist the assistance of a professional local plumber. Our team at Mr. Rooter Plumbing of Greater Syracuse can assist you with locating, maintaining, or replacing your home’s sewage tank.

Request an Estimate for the Job

How Do I Find My Septic Tank

What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00

How Do I Find My Septic Tank

Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.

A tiny proportion of septic tanks have a capacity of 3000L or more.

Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.

If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system. To learn more about our wastewater treatment plant, please visit our Waste Water Treatment Plant website.

How Can I Find My Septic Tank?

According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).

Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.

In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.

• They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
• Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
• A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
• Using an electronic service locator, you may locate a septic tank.
• In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
• Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
• Does it make sense for me to have many toilets and also multiple septic tanks?

It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:

• There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.

The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.

Check the rest of the toilets in the home by repeating the procedure.

Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.

a link to the page’s load

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

1. 3.
2. Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
3. Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
4. When you do, that’s when your septic tank comes into play!
5. Look for the Lid.
6. You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
7. Those areas should be excavated in order to disclose the lids.
8. Get in touch with the pros.
9. Lifting concrete lids will necessitate the use of specialized equipment.
10. A fall into an unprotected septic tank has the potential to be lethal.
11. Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

How to Locate a Septic Tank

A surprising number of homeowners have had to figure out how to find the location of a septic tank on their premises. If you’re purchasing a home with a septic system or discover that your property’s tank hasn’t been maintained in years, you’ll want to know where the tank is located because all septic tanks must be pumped at some point in time. In the course of a real estate transaction, the property owners or real estate agent may be aware of the location of the tank. Inquire about the “as-built,” which is a schematic of the septic system and the specifics of its installation.

Unfortunately, locating the septic tank may not be as simple as it appears.

Because septic system permits have only been needed in Oregon since 1972, you may have to depend on visual indicators to determine whether your system is working properly.

1.Follow the Outgoing Sewer Pipe

Look for the four-inch sewage pipe that runs through the structure and the location where it exits the building in the basement or crawl space. Locate the location outside the building where the pipe exits the building or the location of an access cover over the pipe. It is required that septic tanks be at least five feet away from the structure, although they are usually between 10 and 25 feet away. You may follow the pipe all the way to the tank using a metal probe. It is important to note that sewage lines may curve and run around the corner of a building rather than following a straight path to the holding tank.

2.Search for Septic Tank Risers and Lids

Depending on their age, septic tanks are either one- or two-compartment structures. Each compartment has a cover, with two additional lids for dual-compartment tanks that were added later. If the tank includes an access point known as a riser, the lid may be readily visible from outside. Look for round, plastic discs that are about a foot or two in diameter. Due to the fact that the lids might be flush with the ground or just a few inches above it, they can get overrun with grass and other plants over time.

Tanks without risers are likewise equipped with lids, however they are located underground.

3.Find the Drain Field First

In the absence of a riser and lid, search for indicators of a drain field, such as an area of grass that grows more quickly or more slowly than the rest of the yard, grass that is a different color from the rest of the yard, or areas where snow melts more quickly than in other parts of the yard. Spots of high or low ground in the yard might possibly indicate the presence of a subterranean tank or drain field. You will be able to discover the tank if you probe these regions.

Reasons to Hire a Contractor for Help

Attempting to locate a septic tank on your own can be risky, and in some cases, lethal, if the septic system is old and in danger of collapse. In the event that you fall into a cesspool, dry well, or septic tank, you will die.

Removing septic tank lids on your own might potentially put you at risk of contracting bacterial or virus diseases. If you detect any of the following issues, please contact a contractor to assist you in locating or inspecting your septic tank:

• Soil that is sinking around the tank or drain field. Drainage backup into the home’s sewer system, or toilet backup
• A foul odor in the area where you assume the tank and drain field are located
• When there is no rain, pooling water, muddy soil, or spongy grass might occur. Septic tank covers that are rusted, cracked, or have been replaced with improvised lids are prohibited.

Even though you may be ashamed about forgetting where your septic tank is, it is a very frequent problem among homeowners. A contractor may assist you in locating it, and he or she may do it as part of the pumping service. If you need assistance locating your tank or if you have any other questions, please contact us at 503-630-7802. We are available to assist you!

Septic Systems-What To Ask Before You Buy Land

Articles on Septic Systems Testing of the Soil and Perc What a Septic System Is and How It Works Septic System Upkeep and Repair NEW! Septic Systems that are not conventional See Also: Septic System Frequently Asked Questions See all of our LAND BUYING articles In order to buy land in the country if you’re from an urban or suburban region, you’ll need to become familiar with wells and septic systems. For city dwellers, water arrives out of nowhere at the faucet, and wastewater travels off to a distant location just as effortlessly.

Problems with either the well or septic systems can result in major health consequences as well as significant repair costs.

HOW A SEPTIC SYSTEM WORKS

In locations where there are no municipal sewage systems, each residence is responsible for treating its own sewage on its own property, which is known as a “on-site sewage disposal system,” sometimes known as a septic system. Septic systems are typically comprised of a waste pipe from the home, a big concrete, fiberglass, or plastic septic tank, and an aleach field, among other components. One of the most frequent types of leach fields is composed of a succession of perforated distribution pipes that are placed one after another in a gravel-filled absorption trenches.

SEPTIC SYSTEM CAREMAINTENANCE

Many individuals don’t pay attention to their septic system until they experience difficulties, such as slow drains or backups of sewage. If the drain field is entirely blocked by that time, it may be beyond repair and may require replacement. Fortunately, basic care and affordable maintenance may keep your system functioning for decades without requiring any major repairs. click here to find out more

SOIL AND PERC TESTING

Traditional septic systems can only function properly if the soil in the leach area is sufficiently porous to allow the liquid effluent flowing into it to be absorbed by the soil. There must also be at least a few feet of decent soil between the bottom of the leach pipes and the rock or impermeable hardpan below, or from the bottom of the leach pipes to the water table. Depending on the municipality, particular criteria may differ, however any of these qualities may exclude the installation of a basic gravity-fed septic system.

ALTERNATIVE SEPTIC SYSTEMS

If your lot does not pass the perc test, some towns may enable you to construct an engineered system as a backup plan if the perc test fails. Because a “mound” system functions similarly to a normal system, with the exception of the fact that the leach field is elevated, it is frequently used when the issue soil is too thick (or, in certain situations, too permeable), too shallow (over bedrock or hardpan), or the water table is too high. The mound is comprised of a network of tiny distribution pipes that are embedded in a layer of gravel on top of a layer of sand that is normally one to two feet deep.

Whether or not alternative septic systems are permitted.

Is It Possible for Septic Systems to Last a Lifetime? How Much Slope Do You Need for a Septic Line? Performing an Inspection on a Septic System When Is the Best Time to Take a Perc Test? Should I use a Sand Filter with my existing septic system? Testing for the presence of WellSeptic

Reader Interactions

“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.

Why you need to know where your septic tank is located

If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.

In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.

How to find your septic tank

1. Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
2. Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.

After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.

• The post was published on July 16, 2019 under the category Septic Tank System.

Buying Vacant Land: Will You Need a Septic System?

Have you discovered the ideal plot of land on which to construct your dream home? Great! Although you may be satisfied to use an outhouse, you should investigate if a sewer system is already in place on the land, or whether you will be required to establish a sewer system. The response will have an impact on not just your overall plans for the property, but also on your building timetable and budget, among other things.

Is the Property Served by a Sewer?

The first question to ask is whether or not the property is already served by a sewer system. A septic system will be required in this case. The simplest approach to find out is to speak with the seller of the land or, if there is a real estate agent involved, ask them. If no one is immediately accessible to inquire, you can hunt for hints on your own if no one else is. Given that municipal water is readily available on the property, it’s likely that the property is also served by a sewage collection and treatment system.

Consequently, if the property is located in a city, township, or a densely populated region, a public sewer system is most likely available.

Aside from that, if the property is huge and spread out over many acres (for example, land suited for a ranch or a farm), it will almost certainly require its own septic system.

Costs of Connecting to and Using an Existing Sewer System

If the property is served by a sewage system, the process is quite straightforward. As a landowner, your primary responsibility is to establish the link between the new residence and the main system of distribution. If you wish to build your own septic system or alternative wastewater treatment system, you will very certainly be denied permission to do so. An competent general contractor or plumber should be able to provide you with an estimate of the time and money that will be required. Typically, the cost is less than the cost of constructing a standard septic system, which is a significant savings (and much less than to construct an alternative septic system, described further below).

Once you’ve been connected, your service provider will charge you a quarterly sewer use fee, which will most likely be added to your monthly water bill.

Depending on whether or not a sewer system is available, municipal rules may require you to pay sewer connection costs before you can be awarded a building permit.

If the Property Isn’t Served by a Sewer: Regulations on Septic Systems

If you are required to establish a septic system (since there is no sewer system available on the property), this will take more time and money than just connecting to a sewage system. The construction and maintenance of septic systems are governed by state and municipal legislation in nearly every jurisdiction since failed septic systems are a major source of water contamination (as a result of germs invading adjacent water supplies). Before you can establish a septic system, you must first verify that you are in compliance with all applicable regulations.

A site evaluation is typically necessary prior to the issuance of a septic permit.

A professional site evaluator or engineering company may do them for you, or the local health agency can do it for you.

What the Site Evaluation Will Tell You

It will be determined by the findings of the site evaluation whether you will be able to construct a conventional (gravity-fed) septic system or whether an alternative system will be necessary. Alternative septic systems are basically modified versions of conventional septic systems that are particularly designed to operate with the soils and terrain present on a particular site. Alternative septic systems are also known as bioretention systems. As a consequence of the site evaluation, if the results indicate that your property is inappropriate for a traditional septic system, an engineer or an expert in septic design will need to develop an alternate system.

It is possible that alternative systems will be many times more expensive than a traditional system. This is in addition to the expense of engaging a professional to do or evaluate a site evaluation as well as create the septic design for your system.

Make Sure You Have Enough Room Left for the Home

Septic rules also dictate where a septic system may be placed on a property and how large the system can be. It is required that septic systems be placed back a specific amount of distance from wells and other sources of water as well as from roads, driveways, buildings, and other structures as well as from property borders. These limitations might have a significant influence on where you can build your house. You must guarantee that there will be enough space to put the septic system in a good place, as well as a well (if necessary), and that there will be enough space to build the size of home you wish in an acceptable location when all of this is completed.

Protecting Your Interests Within the Purchase Contract

A site evaluation may have a significant influence on how much money a property is worth, thus it is smart to condition the acquisition of any unoccupied land without sewage connection on having an approved site report. Having the option to negotiate the purchase price or even cancel the contract if the findings of the site evaluation are unsatisfactory will be important to your success. The inclusion of such a contingency in your purchase contract should be made possible by the assistance of an expert real estate attorney.

Where’s my septic tank?

There are a few solutions available if the previous homeowner failed to supply this critical information or if you have misplaced your original copy:

• If your house was built in the previous five years or fewer, thelocal DHEC officemay have a copy of your permit on file. A copy of a septic tank permit can be obtained from the local office by any individual or group, regardless of whether or not they own the land in question. Because of this, it is highly recommended that you have as much of the following information as possible ready at the time of your request.

• Number of the tax map
• Lot number
• Block number
• Address in the physical world
• When the system was installed or when the house was built (if this information is available)
• Name of the original permit holder (if any information is available)
• Name of the subdivision (if the property is located within a subdivision)

• You may also submit a request for a copy of the permission through our Freedom of Information office, although this is not mandatory. To obtain a copy through the Freedom of Information Office, please complete and submit a copy of the DHEC FOI form. Instructions are given with the application. If feasible, please include the information about the property that is stated above. When looking around your yard, search for manhole covers or lids that have been buried by grass or leaves if your house was constructed before 1990.

Tags

Septic Tank Alerts Septic Tank Alerts

Septic & Land Development

When developing land, it is critical for the developer, engineer, or homeowner to schedule a meeting with SWDH in order to explain the project in detail.

SWDH requires that you attend this pre-development meeting before proceeding with the formal application process. Download the Subdivision Application from our Document Repository, which may be found under the Land Development category. Contact208-455-5400.

After the Idaho Department of Environmental Quality (IDEQ) or a Qualified Licensed Professional Engineer (QLPE) has conducted the necessary reviews of the specifications, the SWDH works in collaboration with the IDEQ to release sanitary restrictions on platted subdivisions that are served by city water and city sewer. Please adhere to the Mylar Signature Checklist, which may be found in our Document Repository under Land Development. for subdivisions including municipal water and city sewage services.

1. The SER can be downloaded from our Document Repositoryunder Land Development.
2. Additionally, depending on the location of the subdivision, the size of the lots, and the density of residences, the SWDH may require a Nutrient Pathogen Study to be completed.
3. When developing property, it is critical for the developer/engineer to organize a meeting with SWDH in order to explain the project in more detail.
4. Download the Subdivision Application from our Document Repository, which may be found under the Land Development category.

Fees:

Service Description	Charges
Subdivision Engineering Report Application Fee	$250.00
Cost Per Developable Lot	$300.00
Subdivision Application – City Services (Requires DEQ Approval)	$150.00
Central/LSAS	$1,000 + $100 per 250 gpd
Pre-development site evaluation for commercial or engineered lots (includes multiple test holes and evaluation results)	$850.00
Pre Development Meeting (Fee to apply toward SER application if within 12-months of pre-development meeting)	$100.00

The developer, engineer, or homeowner must schedule a meeting with SWDH in order to discuss the project before any work begins on the land. SWDH mandates that this pre-development meeting take place before the official application procedure may be initiated. Download the Subdivision Application from our Document Repository, which may be found under the Land Development section. Contact208-455-5400. SWDH works in collaboration with the Idaho Department of Environmental Quality (IDEQ), releasing sanitary restrictions on platted subdivisions that have city water and city sewer only after IDEQ or the Qualified Licensed Professional Engineer (QLPE) has conducted the necessary reviews of the specifications and approved the restrictions for release.

• Prior to relieving sanitary limitations on a subdivision that makes use of individual wells and individual subsurface sewage disposal systems, the subdivision must submit a Subdivision Engineering Report (SER), which may be found in our Document Repository under Land Development.
• Additionally, depending on the location of the subdivision, the size of the lots, and the density of residences, the SWDH may require a Nutrient Pathogen Study to be conducted.
• When developing property, it is critical for the developer/engineer to organize a meeting with SWDH in order to explain the project in further detail.
• Download the Subdivision Application from our Document Repository, which may be found under the Land Development section.

Subsurface Sewage Disposal Systems

The Southwest District Health (SWDH) Environmental Health Services division, in collaboration with the Idaho Department of Environmental Quality, controls underground sewage disposal systems (IDEQ). If the developer or homeowner has any questions about the application or permitting process for a subsurface sewage disposal system, they should contact SWDH at (208) 455-5400. This is especially important because a subsurface sewage permit is usually required before a county building permit can be obtained.

Process/ How to Apply

SWDH must perform an on-site examination prior to issuing a permit for underground sewage disposal before the permit may be issued. The applicant must make arrangements for a backhoe to be brought in to dig a ten (10) foot test hole at the time of the examination.

When submitting an application, SWDH requires a legal description, zoning certificate, tax assessment notice, or property profile, among other things. It is possible to obtain your legal description by contacting the county or by consulting a tax notice.

How to Apply

Download the Subsurface Sewage Disposal Application (PDF) from our Document Repository, which may be found under Septic Systems. Please also include an 8″ x 10″ copy of the home floor plans, verifying the amount of bedrooms, if the house is being built from scratch.

Accessory Use

Accessory Use permissions from the county may be necessary before a building permit may be issued for the construction of an addition, shop, or other structure on a piece of property in certain circumstances. The proposed plan will be evaluated by an Environmental Health Specialist at the time of the Accessory Use Application to see if it will necessitate a modification to the existing subsurface sewage disposal system. The Accessory Use Approval Application and Plot Plan (both in PDF format) may be found in our Document Repositoryunder Septic Systems and can be downloaded.

How to Tell If You Can Install a Septic System

Before acquiring a lot, take into consideration if the property has access to a sewer system – or whether it does not. Identifying whether or not the site will require a septic system or other wastewater treatment can make a significant impact in the kind of activities you can carry out on the property. The following are a few methods for determining whether or not your property will require a septic system or an alternate wastewater management system:

Does the Property Have Any Access to Municipal Sewer Lines?

If your property does not have access to municipal sewer services, you will be required to install a septic system. You can find out if this is the case by speaking with the vendor about the situation. Obtaining drawings, blueprints, or property documents can also assist you in determining whether or not the property has connection to the city sewer system. If your property is bordered by other buildings or houses, you may be able to inquire as to whether or not they are using a septic system or the sewer system for disposal.

In contrast, if the lot has a significant amount of land, is located outside of the town borders, or is located in an unpopulated location, you will almost certainly require a septic system.

Does the Property Have Public or Private Road Access Issues?

Is it possible to get to the unoccupied land through a public road? Is the land bordered by property that is held by another person? In some cases, access concerns might prevent you from connecting to public utilities. For example, if you have to travel via private roads to get to the property, sewer lines must likewise travel through private roads. When the majority of the lines must pass through private land, towns are less likely to expand their boundaries. Similarly, expanding out too far from the lot in order to try to reach the municipal boundaries might result in high construction costs and significant construction challenges.

It is possible that you may have to arrange an easement with your neighbor if your property is landlocked.

In contrast, requesting permission from a neighbor to lay a sewage line across their property will result in far more red tape, contractual duties, and other complications.

A septic system is a possible alternative for people who have difficulty getting to their homes. Septic systems may be required in some cases because to public and private access difficulties, rather than just being an option in other cases.

Does the Property Have the Permissions for Septic System Installation?

There are many different types of septic systems available, but many jurisdictions have rigorous laws and regulations in place surrounding them. For example, the state of Pennsylvania has septic system restrictions that apply across the whole state. In addition, local governments such as municipalities, boroughs, and townships have their own set of rules and laws. According to local ordinances, the type of septic system you may use, the location in which it can be installed, and the method by which you can install it on your land may all be restricted.

It is possible that the property may not be able to support a septic system at all and will require an alternate solution.

• There is insufficient room to fit the system. There are no suitable areas that are not too near to water supplies or other properties
• Land fails soil testing, and there is no way to remediate the soil
• Site conditions are deplorable, and there is no way to improve them

When soil testing results in a negative result, obtaining a permit to construct a septic system is almost always impossible. The soil drainage rate will be determined by the test, which is also known as a perc test. In order to function properly, septic systems must have adequate leech field drainage. If the drainage rate of your land does not satisfy the criteria of the town, you will be unable to establish a septic system. This does not rule out the possibility of building anything on the site at all, but it does rule out anything that may be used as a residence or place of business.

In rare situations, it may be possible to have the soil tested in a different location on the property.

If you find the information supplied by the municipality to be unintelligible, you can seek more clarification by doing web searches and posing questions to the municipality.

In addition to excavation, Walters Environmental Services also provides professional septic system services such as perc testing, system design, and other services.