How Many Risers On A Septic Tank? (Question)

How many risers should a septic tank have? A single riser is required for accessing the pump chamber for this type of system. If you don’t have two additional risers, you should locate your septic tank and install risers for both the inlet and outlet openings, as described above.

How many septic tank risers do I need?

A single riser is required for accessing the pump chamber for this type of system. If you don’t have two additional risers, you should locate your septic tank and install risers for both the inlet and outlet openings, as described above.

Can you stack septic tank risers?

A septic tank can be installed usually 3 feet below the surface, but the average is approximately 18 inches. Risers can be stacked on top of each other until they can reach right below the surface.

Should I put a riser on my septic tank?

Having a riser in place can also significantly reduce the cost of septic tank maintenance over time through the ease of access and time on the job saved. Plus you will be spared digging up your lawn every time as well.

Should I bury my septic tank lid?

A septic tank stores the solids from drains and needs to be pumped out about every two years, so it’s not a good idea to cover the area — you need to always be sure where to find the tank. Modern septic systems have an 8-inch plastic pipe that rises from the tank to a few inches above grade.

How do you measure a septic tank riser?

Measure the diameter of the manhole cover: If 26-29 inches, the riser will fit down into the tank opening. Measure the distance from ground to the top of the septic tank and ADD 3 inches. If more than 29 inches: a 3-foot square fiberglass plate (with 22-inch hole in the center) is needed.

How much weight can a septic tank riser lid hold?

The 24-inch solid fiberglass DuraFiber riser lid from Orenco Systems has a flat-style lip for PVC and HDPE pipe. It weighs 10 pounds, but resists damage from lawn equipment and can withstand a 20,000-pound load.

How high should septic risers be?

Determine Riser Height. Tank risers are typically installed about 3 inches above grade. Having the lid above grade will make it easy to find, however, some people will choose to have the lid just a couple of inches below grade so that is easier to mow over and less visible.

How do you seal a septic riser?

Seal the riser to the septic tank using the patch mix. You may finish sealing by adding Bentonite or casing sealer around the base, filling in gaps as needed. Make sure you then carefully secure the riser lid with the screws provided to avoid a safety hazard! All risers must be completely sealed to the septic tank.

Can you cover septic tank lids?

If you have a traditional septic system, the tank should be pumped every 3-5 years. That means that the septic lids should be accessible every 3-5 years. You can use almost any temporary, movable objects to cover your lids, like: Mulch (but not landscaping)

How far apart are septic tank lids?

The distance between lids will be different for each sized tank: 1000 gallon tank = 6-6.5 ft.; 1250 gallon = 7-7.5 ft.; 1500 gallon = 8.5-9 ft.. Dig up the outlet chamber access lid. If you are extraordinarily lucky, the as-built drawing is accurate and you have hit the lids spot on.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

What You Should Know About Septic Tank Risers

Septic tank risers are an important part of any septic system, and they should be installed in every home. This article will give you an overview of septic tank risers and how they can help your septic system. What Is the Function of a Septic Tank Riser? A septic tank riser is a pipe that connects your home’s surface drainage system to your septic tank beneath the ground level. The riser connects to the septic tank at the pump-out openings or access port. Septic tank risers are equipped with lids that can be easily removed to allow you to inspect or pump your septic tank without having to dig up your yard.

These structures are typically made of materials that degrade slowly over time, such as plastic or concrete.

What Are the Benefits of Risers?

Normally, this means digging up your yard before the pump and reburying the tank afterward.

With a septic tank riser, this can reduce the labor in pumping your septic tank.

Since the riser is visible above the surface of your yard, it also serves as an excellent signpost to easily locate your septic tank the first time.
Septic tank risers are not only convenient, but they are also cost-effective if you plan to say in your home for several years.
Concrete risers are more durable but also more expensive, and the cost will depend on the quote you receive from the installing contractor.

Labor costs make up a significant portion of what contractors charge for septic system inspection and pumping, so having a riser could potentially cut the future cost of septic service in half.
Every home can benefit from a septic tank riser, but that does not necessarily mean you should install one today.
This allows the pump and riser installation to be done in one step.

A riser should be a long-term investment, so you want to be sure that your tank is in good working order before installing one.
A septic tank riser is a simple concept that can save you a lot of money and frustration for septic system maintenance.

If your septic system needs a riser or any other service, contact us atSouthern Sanitary Systems Inc. We look forward to hearing from you and answering all your questions about your septic system needs. Please let us know how we can help you and your septic system today.

The benefits of septic tank risers

Installing septic tank access risers will save you money as well as your back. Accessing the septic tank is made simple by the use of rippers. | Photo courtesy of the Michigan State University College of Agriculture and Natural Resources The process of finding and pulling up the lid to your septic tank may be time-consuming and frustrating. In many cases, homeowners aren’t even sure where to begin their search for the lid to their septic tank. Some people are just unable to pull themselves out of a hole.

What method do individuals use to locate the buried treasure that is their septic tank lid?
Others look for a clue, such as a dead spot of grass or other visual signals, to help them find their way.
Whatever way you choose, digging it out is still necessary, and if the correct location cannot be discovered, another hole must be excavated.

Some counties, such as Kalamazoo, Oakland, and Otsego, mandate that septic tank access risers be erected; these are just a few examples.
Contact your Michigan County to find out about the most recent onsite waste water rules that apply to you.
A septic tank riser is a pipe that can be built of plastic, fiberglass, or concrete to carry waste away from the tank.

The lid is then either left uncovered or covered with a very thin layer of soil and grass, depending on the preference of the gardener.

It goes without saying that any modifications to your septic tank or system will need to be approved by your county environmental health department or another qualified inspector.

You may arrange the installation of a riser in your septic system to coincide with your usual septic system maintenance schedule.

It is also possible that having a riser in place will dramatically lower the overall cost of septic tank maintenance over time, owing to the increased ease of access and reduced time spent on the operation.

MSU Extension Educator Beth Clawson can provide further information on the onsite waste water systems you may be interested in.

The Michigan Department of Natural Resources has a team of natural resources educators working to provide aquatic invasive species instructional programming and support throughout the state.

You can reach out to an educator using MSU Extension’s ” Find an Expert ” search engine by searching for “Natural Resources Water Quality” in the keywords field. Resources:

Did you find this article to be informative?

You Might Also Be Interested In

If you have an older septic system, you may be wondering what a septic tank riser is and why you would need one. Traditional systems were designed to be out of sight, out of mind; they were buried for 15-20 years with no consideration given until they required emergency pumping or repair. Newer septic systems now have risers, which are a positive thing, since they provide a more efficient way of draining the tank. Septic tank risers provide simple access to your septic tank from the ground level as well as increased view into the operation of your septic system.

The Benefits of a Septic Tank Riser

Before we go into the advantages, it’s important to understand what a septic tank riser is. Riser are often built of plastic or concrete, depending on the use. They are enormous circular pipes that are installed above the cleanout entrance of the septic tank and are long enough to extend the cleanout opening all the way to the ground level. The advantages are as follows:

Even when the ground is frozen, it is possible to get access during the winter months. Maintenance and pumping of the septic system may be done quickly and easily. Septic system repair should not need digging up your yard. A visual reminder of the importance of your septic system

The last advantage may appear to be somewhat counter-intuitive. What are the benefits of having a visual reminder of your septic system? Preventing premature septic system collapse is possible through periodic septic system maintenance. With a septic tank riser, you’ll not only be able to identify the position of your septic system, but you’ll also have a visual reminder to have your system pumped at least once every two to three years as well. However, the septic tank risers that we install are intended to fit in with the surrounding environment.

How Much a Septic Tank Riser Costs

In your house, your septic system is one of the most vital mechanical systems to have working properly. A septic tank riser, which costs only a one-time installation price, can safeguard your septic system for many years to come. The ease with which maintenance and pumping may be performed will almost instantly result in a return on your investment. You may also say goodbye to costly and unsightly excavations when it comes to upkeep. Although the ground may be frozen in winter, you will be able to inspect your septic system visually even during the coldest months of the year.

This will result in costly emergency repairs.

If you would like to learn more about how septic tank risers might assist you, please contact us at 800-595-7907.

Traditional systems were designed to be out of sight, out of mind; they were buried for 15-20 years with no consideration given until they required emergency pumping or repair.

Newer septic systems now have risers, which are a positive thing, since they provide a more efficient way of draining the tank. Septic tank risers provide simple access to your septic tank from the ground level as well as increased view into the operation of your septic system.

What are the benefits of a septic tank riser?

Even when the ground is frozen, it is possible to get access during the winter months. Maintenance and pumping of the septic system may be done quickly and easily. Septic system repair should not need digging up your yard. Your septic system will be visible as a reminder

The last advantage may appear to be a bit counter-intuitive. What are the benefits of having a visual reminder of your septic system? Preventing premature septic system collapse is possible through periodic septic system maintenance. With a septic tank riser, you’ll not only be able to identify the position of your septic system, but you’ll also have a visual reminder to have your system pumped at least once every two to three years as well. However, the septic tank risers that we install are intended to fit in with the surrounding environment.

How much does a septic tank riser cost?

In addition to protecting your system and saving you money, a septic tank riser is a reasonably easy solution.

We’d be happy to tell you more about how septic tank risers might help you.

for an appointment or to learn more about our services.

Felix Septic Service is a company that provides septic service. 2020-05-19T15:44:01-04:00

Installing Access Risers

In order to perform fundamental septic system maintenance, you must first evaluate the condition of your septic tank and pump chamber (if you have one), which can be time-consuming and labor-intensive if you do not have access ports known as risers. Consider the prospect of having to dig through two feet of dirt to check the oil on your vehicle. Installing septic tank risers for an off-site septic system is broken down into four steps, which are outlined below. Please keep in mind that the currentWashington State Coderequiresrisers for all septic systems, which means you may be forced to install one if you are asking for a construction permit, land division, or any other type of official action in the state.

A few safety tips before you get started:

Struck by an underground electrical wire while excavating may be quite dangerous! If you are in any way doubtful about the presence of subterranean lines on your property, you can have them found by contacting 1-800-424-5555 or 811, or by visiting the website
Use the buddy system to your advantage! Working with a partner is usually recommended since the fumes connected with open sewage can be dangerous and cause a person to go unconscious. Never leave a septic tank that is open unattended! Once the lids have been removed, exercise caution around the tank and keep dogs and children at a safe distance. Examine the structural integrity of your septic tank! If a septic tank is more than 20 years old, it is recommended that it be pumped to ensure that the tank’s structural integrity and water-tightness are not compromised. Instead of spending money on costly repairs, it is preferable to replace the tank with a contemporary septic tank that includes risers as part of the installation. A permit from your local Environmental Health department is required for the replacement of a septic tank.

Gather all the MaterialsTools You will Need

It should be possible to get most of the components required to construct a septic tank riser at your local plumbing hardware store or on the internet. PVC risers are available in a variety of shapes and sizes. Some of the brand names you might be familiar with include “Tuf-Tite,” “Polylok,” and “Orenco.” Risers are typically 24 inches in diameter and may be readily inserted into the tank hole opening without difficulty. Due to the fact that certain tanks have square openings, it might be difficult to fit a riser around the square entrance.

Some types of risers are made to order based on the height you want, while others are available in increments of 6-12 inches.

Then purchase an Adapter and Risers that are somewhat bigger in diameter than the hole.

See below for Step 4 on attaching risers to the tank entrance. For the purpose of installing a riser system on your septic tank, you will require the following components:

Tank Adapter Ring (TAR)

Riser Adapter Ring Kit
Butyl Rope
Risers

Domed Lid OR Flat Lid
Stainless Steel Screws

The following materials will be required for digging up your septic tank(s):

As-built condition of the sewage treatment system The following items are required: sketch on paper, measuring tape, shovel, probing instrument, eye protection, and work gloves.

To cut risers to the proper size, the following tools are required:

Circular saws, saber/jig saws, and hand saws

Raspor file
Marking pen
Tape measure

Drill with a 1/4″ bit

Materials required to seal the risers to the tank include:

High-strength concrete patch mix

A small bucket
A mixing stick
And gloves

Follow the four simple procedures shown below to install access risers on your septic components, or download and print a copy of theSeptic Tank Manhole and Access Riser Installationbrochure from Thurston County Environmental Health to get started right now.

Step 1: LocateYour Septic Tank(s)

When looking for your underground septic tank or tanks, it is essential to consult the ‘As-built’ Record Drawing linked with your septic system for assistance. Essentially, this is a plot diagram that shows where your septic system was put on your property, as well as distances between septic components and notable landmarks. The Online Permit System will guide you through the process of locating septic-related documentation if you do not have a “as-built” document. It is possible that you may need to contact Environmental Health to examine the paper records or seek a specialist to find your tank if an as-built is not accessible.

Probing the area around the septic tank with the probing instrument until you contact concrete should be done lightly.

The presence of underground electricity or other utility lines and cables might put your septic tank in danger.

Call 1-800-424-5555 or 811 or go online to make sure that any electrical utilities are found before you begin digging before you begin digging.

Step 2: Uncover Your Septic Tank (s)

Once you’ve discovered your septic tank, you may start digging about. The tank is typically 6 feet wide by 8 feet long, with the width being the largest size. Remove all of the pebbles and debris from around the tank’s lid openings and dig out the whole top of the tank. You will want to clean out any dirt that has accumulated on the surface of your septic tank. This will assist you in ensuring that you generate a high-quality seal. You should have two openings: one over the inlet (which comes from the home) and another over the outlet (which comes from the yard) (into the drainfield or pump chamber).

You’ll need a riser for each of the doors you open.
Typically, the inlet side is the one that is nearest to the home.

When cleaning the tank, it is beneficial to remove the complete top of the tank.
Risers must be modified in order to be correctly installed, and all manholes (holes 24 inches or bigger in diameter or square in shape) must also be updated, as well as the tankinlet and outlet baffle covers (if separate from the manholes).
If you discover one – and only one – riser already installed, it is most likely for the pump chamber, which only requires a single riser to provide access to the pump to function properly.

Remove the concrete lids so that they may be disposed when the project is completed.
Consult your’As-built’Recorddrawing to establish whether you have a distribution box (D-box), which you will also need to unearth and place a riser on if you have a typical gravity system.
Once the lids have been removed, proceed with caution around the tank.

Inform someone of your whereabouts in case you are involved in an accident.

You should be aware that exposure to sewage can result in serious sickness, so make sure you wear gloves and thoroughly wash your hands afterward with soap and water. It is also recommended that you wear eye protection in the event that debris falls into a tank and splashes back at you.

Step 3: Fit Risers to Component Openings

In accordance with the diameter of the septic tank manholes, huge risers will either sit on top of the septic tank or will fit down into the aperture of the tank by 1-3 inches. It’s important to keep this in mind while calculating the height of the riser. The surplus can be easily removed; nevertheless, it is difficult to add a few inches to the length. Take the following measurements of the manhole cover’s diameter:

Theriser will fit into the tank hole if the aperture is between 26 and 29 inches in diameter. Measure the distance from the ground to the top of the septic tank and multiply the measurement by three inches. The following is required if the aperture is greater than 29 inches: a 3-foot square fiberglass plate (with a 22-inch hole in the middle) is required. In this case, it lies above the manhole and narrows the aperture, allowing a 24-inch riser to be utilized instead of a more expensive 30-inch riser, saving money.

The distance between the ground and the top of the fiberglass plate should be measured. You may choose to place the risers so that they are level with the surface of the ground, or you may want them to stand out a few inches above the ground (if a riser is above ground make sure you are careful when mowing). Tips: To shorten a big riser with ribs, drill a 1/4-inch hole between the ribs above the cut line and finish the cut by following one of the grooves between the ribs with a saber/jig saw to finish the cut.

By eliminating one of the ribs from the largeriser, it may be made to fit more snugly into a smaller manhole entrance.

Step 4: Attach Risers toSeptic Tank (s)

It is recommended to pump out an old septic tank that is 20 years or older in order to check its structural integrity and water-tightness before using it again. If the tank requires extensive repairs, it is preferable to replace it with a new septic tank that includes risers as part of the installation. A permit from the local health department is required for the replacement of a septic tank. Remove any dirt and debris from the tank’s surface by cleaning it off. Using the butyl rope, construct the components of the risers in accordance with the manufacturer’s instructions.

Jet-Set, Rapid-Set, Thorough-Set, and Perco-Plug are just a few of the brand names available.
NOTE: For optimal results, just a little amount of concrete patch should be mixed at a time.
The patch mix should be used to seal the riser to the septic tank.

If you want to avoid a safety danger, make sure you properly attach theriser lid using the screws that come with it!
Risers for inlet or outlet apertures that are smaller than the openings should have the bottom few inches sanded with rough sandpaper to allow a firmer connection between the two surfaces.
A useful source of information on correct installation of risers on septic tanks may be found at your local hardware store where you purchased the risers and covers.

Thurston County Environmental Health is should be commended for providing the foundation for this documentation.

Septic Tank Risers & Lids

Sewage tank risers are meant to raise the access level of an underground septic tank to the surface, allowing for easier access for normal pumping and maintenance tasks. Riser installation in your septic tank eliminates the need for you to pay for a pumping service to dig up your tank or the need for you to do the digging yourself, saving you money. In addition to being strong enough for direct burial and foot traffic, our septic tank risers and lids are lightweight, which makes them easy to handle during the installation and removal of the tank lid.

We also sell septic covers for corrugated pipe in sizes such as 12″, 15″, 18″, 24″, and 30″.

Riser installation in your septic tank eliminates the need for you to pay for a pumping service to dig up your tank or the need for you to do the digging yourself, saving you money.

The Polylok risers and lids are available in three different diameters: 12″, 20″, and 24″.

THE POLYLOK SEPTIC TANK RISER ADVANTAGE

Risers for septic tanks are available in a variety of sizes, shapes, and designs on today’s market today. Our Polylok risers are simply the best that money can buy in terms of quality. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! Other products need you to purchase or apply some other type of sealant between each riser part, however our Polylok risers eliminate the need for this step completely!

INTERNAL STRUCTURAL RIBS

The Polylok risers are reinforced with structural ribs that run internally around each riser segment, providing them with exceptional strength and allowing them to maintain their shape even after the hole is backfilled with dirt. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

LOW PROFILE RISER LIDS WITH HANDLES

The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it.

The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE TANK ADAPTER RING

An adapter ring is required in order to properly install septic tank risers on your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

Septic Tank Riser Kits – Wholesale Septic Supply

Are you fed up with having to dig up your septic system every time it has to be repaired or serviced? If this describes you, we have a fantastic option for you. In order to modify the way you operate on your septic system, you may require a suitable septic riser, which can be found online.

Why choose Tuf Tite Risers?

The Tuf Tite Septic Riser System allows you to get access to your outside septic system in a quick and simple manner. With the help of this revolutionary instrument, septic system service becomes a snap, and you will never have to dig up your septic system again! This system eliminates any guessing by providing you with the riser and other components you require to complete the task. Because you are ordering all of the essential parts in a single package, you will save both time and money on the installation process.

What are the Tuf Tite Product Specs?

Every riser system is simple to install on concrete septic tank lids, and the kit will even tell you what size access hole will work best with your septic system based on the information in the kit. The riser system is effective on 95 percent of septic systems with round diameter entrances ranging from 16 inches or less to 25 inches or less, and square sizes ranging from 11 inches by 11 inches to 18 inches by 18 inches. Looking for high-quality products? Look no further than this store! There are several sizes available for the Tuf Tite riser system, which has been engineered to last.

Septic tanks are normally installed below the surface of the earth.
Installing a riser kit is the most effective approach to deal with this issue.

When the riser comes into contact with the tank, an adapter ring should be used to seal the connection.
A number of risers will be stacked on top of each other and the adapter ring until they reach the ground level, at which point they will be removed.
This method will establish a barrier around the tank, protecting it from contamination while also making access to the tank more convenient.

In order to ensure that the circular riser will fit around your square or rectangular access port, there are a few things you may do.
The diagonal distance across the access will be the longest distance that a riser will have to cover before it may be used.
Assume that “a” is the length of one side of the port’s access.

For example, A is 12 inches in length and B is 12 inches in length.
The equations shown above can be used to estimate the diagonal distance of a rectangle in a rectangular coordinate system.
The only risers that should be utilized are those having an inner diameter that is bigger than the diagonal distance between the access port and the wall.

This approach will need the knowledge of the lengths of each side of your rectangular access port in order to work. Pythagorean theorem is something you may remember from your geometry training.

The Importance of Septic Tank Risers

Installing septic tank risers are a highly suggested addition to your septic system. Theseptic tank riserwill make maintenance and monitoring your septic system more easier and more convenient.

Septic Tank Risers will Lower Your Septic System Cost

On any new or updated septic system in the United States, authorized septic tank risers are required to be built by law in most states. This obligation, in contrast to many other legislative regulations, really provides advantages. Your septic system is one of the most expensive mechanical elements on your property. It is also one of the most complicated. It is also one of the least watched and least understood systems that you have in your possession, as well. If you don’t have septic tank risers, your system will be “out of sight and out of mind” for a long time.

The average cost of a septic system in the United States is around $15,000.

If you add the interest costs to the $15,000 and divide the total sum by the length of time the system will live, your septic system will cost you more than $1,000 a year to maintain.

The installation of septic tank risers is the most effective method of monitoring your septic system.

Advantages of Septic Tank Risers

Septic Tank Riser Made of Concrete The first advantage of an aseptic tank riser is that it is aesthetically pleasing. Every time you see the riser cover, it will serve as a constant reminder that you have a septic tank. This will help you to remember this truth on a frequent basis. Due to the unattractiveness of the old-style concrete covers, many individuals are uncomfortable with the idea of their septic tank risers being visible in their yard. Modern septic tank risers and covers are significantly more aesthetically pleasing, blend in with the surrounding environment, and are easier to install than previous models.

The concrete coverings are similarly heavy, weighing between 60 and 80 pounds.

Riser rings for septic tanks made of modern polymers are generally less than 30 pounds in weight.

Modern Septic Tank Risers Seal Surface Water

Septic Tank Riser of the 21st Century The fact that they are more easier to seal than older models means that they are better at keeping surface water from entering the tank. Old-fashioned concrete riser rings do not have a gasket included into them. As a result, surface water may readily flow between the connection between the tank and the riser ring, as well as between the lid and the riser ring, when the tank is filled with water. Nowadays, a watertight seal is installed between the septic tank and the base flange of the riser.

To keep little children from curiously messing with the cover and putting themselves in danger of falling into the septic tank, modern riser covers are fastened with threaded fasteners.

How to Inspect Your Septic Tank

On average, we recommend that you examine your septic tank visually once every six months. Simply removing the septic tank riser cover will allow you to do the check. Remove the cover from the tank and measure the height of the water level in the tank. The water level is typically 6″ to 8″ below the inside of the tank cover when the tank is full. The amount of air space above the water should be between 6″ and 8″ according to this rule. Because of how the clean-out cover is installed on your tank, you may be able to view the septic tank’s inlet or outflow baffle depending on the placement of the cover.

According to the outlet baffle (which should be closest to the drainfield), typical water level should be even with the bottom of pipe or no more than 14 inches deep in the pipe.

Other Benefits of Septic Tank Risers

Another advantage of installing a septic tank riser is that it will make the installation of an Aero-Stream Remediation System relatively straightforward. Take off the riser cover and drop the diffuser assembly and bio-brush into the tank. Then drill a 5/8″ hole in the plastic septic tank riser about 2-3″ below the surface of the water to allow for drainage. Connect the airline to the Aero-Stream aerobic generating unit by pushing it through the hole that has been bored. Done. Simple, Quick, and Efficient!

See How Simple it it to install our Septic Tank Riser

Most homeowners consider their septic system to be a “out of sight, out of mind” service that receives little or no attention unless there is a problem. Septic systems are buried underground, and if you aren’t sure where your tank and its components are, it might be tough to discover your access ports or manhole covers if you aren’t familiar with your property’s layout. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings.

What is a septic tank riser and how does it work?
Risers, sometimes known as “extensions,” are available in a variety of heights to raise any access port up to grade.
Because the riser extends from your tank entrance to the lawn surface, it makes it much easier to reach your septic tank for pumping, maintenance, and inspections than it would otherwise be.

Digging down to your septic tank lid or access port and fitting the riser to the entrance are the steps involved in installation.
Then we’ll fill the area around the pipe with earth and put the lid on top of it once it’s in place.

To make the lid integrate smoothly into your yard and landscaping, you are invited to put grass or mulch around the top of the lid. The AdvantagesWhen it comes to septic tank risers, there are a plethora of advantages to consider.

The expense of installing a riser is one-time, but the advantages are long-lasting. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times

There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. This is in addition to the mess that it can create in your yard if the lid is buried several feet down
Nonetheless, it saves you money. Time is money, after all! Furthermore, since it is simpler to reach your septic tank, our staff can complete your task or resolve your problem much more quickly
It is critical to understand where everything is located. If you’re putting up a new patio, house addition, or backyard project, understanding where your tank and its components are located will be quite beneficial to your project. We’ll even draw you a schematic if you need one

Just let us know.

Are you ready to talk to us about septic risers and how they can make your next septic pumping job a whole lot easier? For a $20 discount, call 717-898-2333 and mention this article. We provide service to homes and businesses across Central Pennsylvania, and if you know your tank is due for a pumping, we can install your risers at the same time that your tank is being serviced.

undefined

The inefficiency of having to dig up your grass to access your septic tank whenever it has to be pumped or undergoes periodic maintenance is well known to those who own septic systems. The subterranean placement of the tank is normally a practical method to keep it secure and discreet, but it may make routine duties difficult, expensive, and time consuming. This is why many people opt to install a septic tank riser in order to alleviate these difficulties. As the name implies, it is a concrete or plastic pipe that runs from the pump-out hole to the ground level of a sewage system.

If you’re unsure whether to invest in a tank riser, consider the following advantages and disadvantages of doing so:

A septic tank riser makes it simple to determine where the system is located. PRO – Low maintenance: Besides being useful for maintenance, it may also be useful for monitoring the system’s operation and quickly accessing the system if something goes wrong. BEING ABLE TO FIND THE Septic System FAST may save you valuable time and work. Additionally, it may be able to assist minimize the expenses of any future service visits
Nevertheless, PRO – Protected from the elements: Septic tank risers are intended to endure everything Mother Nature throws at them, including snow, wind, and whatever else Mother Nature has in store for them. Depending on the material used, the riser can be formed of concrete or a thick heavy plastic that is fitted with a highly strong cover to keep the system totally free of dirt. This can help to decrease damage to the system and avoid the occurrence of additional problems. A pipe or lid in the center of a lawn may be considered an eyesore by some homeowners, regardless of how handy it may be in other ways. CON – Convenience: In order to allow the grass to grow over the top of the riser lid, one alternative is to set the lid a couple of inches below the level of the lawn. Afterwards, all you’ll have to do is dig up that location without disrupting the rest of the yard. In most cases, homeowners prefer to build a riser on an existing septic system rather than constructing a new one. This is a project that will require the services of a septic tank professional. Even while this will necessitate some digging and disturbance in the yard, it’s vital to remember that it will ultimately preserve your lawn. CON – Cost:There are certain costs connected with building a septic tank riser, notably the cost of the supplies and the labor involved. Although this is an expenditure that will pay for itself in the long term through years of cost savings during future inspections and maintenance, it is one that should be considered.

It’s evident that building a septic tank riser may be a desirable upgrade, despite the few small drawbacks that may be connected with the process. If you have any more questions, please don’t hesitate to contact the professionals at Mike’s SepticMcKinley Sewer Services. Throughout Prior Lake, MN, we are experts in everything septic. This includes tank and system design as well as installation, accessories, pumping, cleaning, and routine septic maintenance. Reach out to one of our septic system specialists immediately by phone or email!

Best Price on Septic Tank Risers & Covers Online Guarenteed!

Septic Tank Risers and Lids are available from TGWasteWater in a variety of sizes and styles. We also provide a large selection of accessories for our riser products. Are you fed up with having to pay to have your system dug up and pumped every time it needs to be refilled? Are your present concrete risers at danger of collapsing? Is it becoming tiresome to have to lift a hefty concrete cover every time you need to access your tank? It is possible that you responded yes to any of these questions and that you should think about putting a riser system on your septic tank.

Risers from Tuf-Tite and Polylok are available for purchase.

Please keep in mind that Tuf-TitePolylok products are incompatible with one another.

Consequently, if you want us to utilize a Tuf-Tite lid, you must purchase Tuf-Tite Risers, and the reverse is true. Do you have questions about how to build a riser on a septic system? PLEASE CLICK HERE TO READ OUR INSTRUCTION GUIDE ON HOW TO INSTALL RISERS ON A CONCRETE SEPTIC TANK

Benefits of Installing Septic Tank Risers

Many people consider their septic system to be a “out of sight, out of mind” service that they don’t think about until there’s an issue. Due to the fact that septic tanks are underground, it might be difficult to discover the access ports if you aren’t familiar with the area where your tank and its components are placed. Septic tank risers are a straightforward, cost-effective solution to this problem that can result in significant long-term savings. Continue reading to learn more about septic tank riser installation in the Twin Tiers region, or contact us to arrange service now.

It is a large-diameter concrete or plastic pipe that runs vertically from the pump-out apertures or access ports on top of a sewage treatment system down to ground level.
With a lid that fits firmly on top of the riser and lies flush with the ground, digging and searching are no longer necessary.
Installation Every week, our staff completes the installation of risers.
When feasible, we’ll pick a riser that will stretch all the way to the surface of your grass, or we’ll trim one to fit.
To make the lid merge perfectly into your yard or landscape, you are welcome to put grass or mulch around the top.

The cost of installing a riser is a one-time expense. The cost of the extension will be covered after it is completed, and your tank will be easier to access for pumping, maintenance, and inspections. Never again will you have to look for your access ports! When we put your manhole cover up to grade, it will be clearly visible at all times
There will be no more digging! This is especially useful during the winter months, when digging out a buried manhole cover might take several hours and need specialized equipment. Furthermore, it saves you money by avoiding the mess that it might create in your yard. We understand that time is money, and when our staff has simpler access to your septic tank, we can get your project done or your problem resolved more quickly. It’s critical to be aware of where things are at all times. Are you thinking of building a new patio, home extension, or backyard project? The ability to pinpoint the location of your tank and its components is quite beneficial. We’ll even draw you a schematic if you need one
Just let us know.

Are you ready to speak with us about septic risers? When it comes to septic tank repair, this is a straightforward service that will make your life a whole lot simpler. To schedule service, please call us at: 607-564-7931.

Benefits of Tank Risers – Gainesville Plumber

Many vintage septic tanks don’t have risers; instead, they have an entry point in your backyard that’s buried several feet below ground level, frequently beneath several feet of earth. However, your septic repair firm will most likely be able to quickly adapt the tank with a riser to make things more convenient for everyone. Discover some of the advantages of using tank risers.

1. You May Save on Pumping Costs

How would you want to get up each morning and have to shovel through four feet of earth before you can go to work? Although digging down to uncover the septic tank was a standard component of the process in previous decades, installing a riser today can eliminate the need for this step entirely. In fact, some septic providers impose additional fees for the digging or just charge a higher labor rate as a result of the additional time that is required.

It will cost money to install a riser as well, but it is a one-time investment that will save you money on fees for years, if not decades, in the future.

2. You Will Avoid Messing Up Your Landscaping

Your neighbor’s tank riser has a large green lid, and you may decide that you do not want such an unpleasant element in your yard after taking a look at it. Unfortunately, the inevitable digging up of your landscaping that will inevitably occur as a result of a septic pumping is significantly more disruptive to the landscape. If you have a riser installed, you may effectively disguise it by using a miniature wishing well or other attractive cover to hide it from view. It will also allow you to landscape around it without the risk of all your hard work being dug up every few years as is the case with a traditional pond.

3. You Will Have Quicker Access for Emergencies

In the event that you have a riser, you will not be required to consult a map as if you were going to unearth a particularly stinky treasure box. In most cases, your septic professional will be able to arrive on the scene, open the lid, and commence to work straight away. In the event of a septic emergency, this time saving can be lifesaving. It enables workers to go immediately to work diagnosing and repairing the problem rather than wasting time on preliminary work or administrative tasks. Despite the fact that good septic management can lessen the likelihood of an emergency, it is always better to be safe than sorry.

4. You Can Have Safety Features

You want easy access to your septic tank for yourself and for maintenance and repair employees, but you don’t want anybody else to have access to it – such as your children. After all, falling into the tank has the potential to be devastating. As a result, you’ll be pleased to know that many new septic risers are equipped with safety measures to help avoid difficulties. For example, some have lids that are loaded with sand, making them too heavy for children to readily move around with. Others rely on safety screws or sophisticated locking systems to keep their belongings safe.

It will also be equipped with a sufficient number of sturdy screws or similar child-resistant locking device to keep the lid in place.

These four advantages demonstrate how septic risers may help you save time and money by providing a convenient feature that can make your life (and the life of your septic maintenance specialist) simpler.

All of the risers should be of excellent quality and have safety screens.

Get in contact with Billy Bell Plumbing Inc immediately if you would like more information about our pumping services or if you would need risers and safety screens fitted.

Tuf-Tite Septic Tank Riser, 24’x12′ – – Amazon.com

On July 14, 2018, a reviewer in the United States of America verified that they had made the purchase. All of the products in the shot were purchased by myself. I needed to install an RV sewer hookup, and this was the most environmentally friendly method. No more digging around for the lid when it comes to pump out time! 5.0 stars out of 5 for this product It’s a good fit. On July 14, 2018, Stephanie Stanley posted a blog entry. All of the products in the shot were purchased by myself. I needed to install an RV sewer hookup, and this was the most environmentally friendly method.

The photographs in this review On December 30, 2017, a review was conducted in the United States.

It was necessary to first install an adapter ring to the tank riser in order to adhere the risers to the septic tank, then an extra 24 x 6 riser to provide additional height, and lastly a 24 inch flat lid to complete the installation.

Furthermore, if your septic system requires maintenance in the winter, there will be no digging in frozen earth.

Made to be extremely durable.

5.0 stars out of 5 for this product A must-haveDurable and long-lasting Posted on December 30, 2017 by DM This is an absolute must-have if you want to get to your septic tank quickly for maintenance.

You’ll never have to dig yourself out of a hole again.

Simple to set up.

We eventually painted the lid a brownish color to match the surrounding landscape, which was an option.

In order to keep the adapter ring from moving about, I used cement sealing caulk on the bottom lip and then quick dry cement around the bottom edge.

It worked out well and was built to last.

On April 28, 2016, Justin posted a blog entry.

In order to keep the adapter ring from moving about, I used cement sealing caulk on the bottom lip and then quick dry cement around the bottom edge.

It worked out well and was built to last.

Purchase that has been verified I purchased and installed two of these Tuf-Tite risers on my septic tank to replace the concrete lids that were previously there.

In order to keep the water out, I utilized concrete anchors for the adapter ring and putty tape underneath the ring.

I elected to bury the risers approximately 6″ below the surface of the ground and designate their location with a surface marker.

The grass will eventually cover everything, and no one will be able to tell what is going on until the septic tank needs to be pumped again.

Because they would not come off no matter how much pressure I exerted, I was forced to chisel the concrete “lids” off my septic tank.

As a whole, this was around a $300 repair for two risers that should hopefully last the lifetime of the septic tank.

Purchase that has been verified The two of them that I bought will be installed on my septic tank.

The second one arrived a few days later, but it was so deformed (it was in the shape of an oval) that it couldn’t be fitted into the TAR or lid.

I tested the riser with a tape measure and it measured more than 25 inches across at one point and less than 23 inches across the other axis.

In the image, you can see it after I used massive wood clamps to mold it into a spherical enough form to be placed on the TAR.

The lack of quality control and the oval forms of many risers have caused my project to be delayed by more than a week, according to my estimates.

3.0 stars out of 5 for this product Poor quality control and a high number of returns On March 7, 2021, M.D.U.

The first one was excellent; it was a perfect fit for the flat lid and tank adapter ring (TAR).

Amazon issued a replacement, which arrived with the same oval watp as the original.

This lid will fit (barely), but I was unable to get the shape to fit into the TAR without the use of clamps (which do not fit into the hole when installing the risers) because of the form of the lid.

I like that Amazon makes it simple to exchange items, but yeesh.

Hopefully, the third replacement will be successful!

Purchase that has been verified Mine was a little oval, maybe 2 inches out of round, when it came.

There were also screws missing.

Insert the riser into the hole.

Continue to fill the hole with dirt and pack it down until it is full.

It is possible to pack a bit harder on the sides that are bent ‘outward’ if you know which ones they are.

Mine went from being 2″ out of round to being 1/16″ out of round using this procedure.

Purchase that has been verified The Polylok riser base and cover are in the possession of a neighbor.

The TuffTIght base and Riser are well-matched, however the screw points on the lid may be improved.

In addition, the lid specifies that it includes the safety screws, and the lid’s documentation specifies that all screws are included, when they are not in fact.

On September 26, 2019, a verified purchase was reviewed in the United States.

We had finally located the lid, but there was no way we were going to cover it and risk having to dig through this muck once more.

Everything arrived in record time, and the installation was straightforward.

It makes life a whole lot simpler.

By RaeraeandMikeysmom on September 26, 2019First and foremost, let me state unequivocally that digging for your septic tank while experiencing a problem with it is a complete nightmare.

That’s when we made the decision to put in the riser.

Everything arrived in record time, and the installation was straightforward. If you don’t already have one of these and find yourself digging every time you go outside, I strongly advise you to get one installed. It makes life a whole lot simpler. The photographs in this review