How Big Is Standard Lid On Septic Tank? (Solution)

Locate The Lid Most septic tanks are rectangular and measure about 5 feet by 8 feet. Probe around the tank to locate its edges and mark the perimeter of the rectangle. A septic tank installed before 1975 will have a single 24-inch concrete lid in the center of the rectangle.

What are the dimensions of a residential septic tank?

  • Septic Tanks are usually about 4.5 feet wide x 8.0 feet long x 6 feet tall. Tanks are typically buried 4 inches to 4 feet deep depending on local site conditions, shape, slope, and other factors.

How big is an old septic tank lid?

If your septic tank was installed after 1975, it will probably have two polyethylene or fiberglass lids centered at opposite sides of the perimeter. Older tanks will typically have a 24-inch concrete lid right in the center of the tank.

How are septic tank lids measured?

Dig a 30” diameter hole down to the inlet chamber lid. Open the lid and look for the end wall where the 4” sewer pipe comes into the tank from the house. Once you determine where the inlet is, measure the distance from the center of the inlet lid towards the opposite end of the tank to locate the outlet lid.

Can you replace the lid on a septic tank?

Concrete septic tank covers require replacement when they develop cracks or other damage. These can be purchased online or at a home improvement store near you. Many septic tanks have risers so the lid is visible above ground.

How thick should a septic tank lid be?

(12) The top, bottom, ends, and sides of the tank must have a minimum thickness of two and one-half inches. (13) A minimum 28-day concrete compressive strength of 3,500 pounds per square inch shall be used in the construction of the septic tank, concrete access riser and riser cover.

How many lids should a concrete septic tank have?

Two or three lids may be included in your system. The average size of a sewage tank is approximately 5 feet by 8 feet. The lid is buried between 4 inches and 4 feet underground in most cases.

Why does my septic tank have 2 lids?

Solid, watertight, buried tank made of concrete, plastic, fiberglass or metal. This tank has a way in (inlet), and a way out (outlet). So, most residential tanks should have (2) lids about 5′ away from each other. A septic tank holds all the liquid waste from your home (toilets, sinks, kitchen, bathtubs, floor drains).

Should septic tank lid be sealed?

Like wells, septic systems have problems if they are not sealed from outside surface water. Most septic systems rely on buried pipes to get rid of the fluids. The lid covers should fit tightly — if they don’t, a company that specializes in septic repairs should be called to fix them.

How much does a septic tank lid weigh?

The concrete covers also weigh 60 – 80 lbs. Because of the weight, many people are discouraged from removing the cover and doing an inspection. Modern plastic septic tank riser rings typically weigh less than 30 pounds.

How thick is a concrete septic tank lid?

The exterior walls of the septic tank are made of concrete, normally 4 inches thick.

What size is a septic tank lid?

Find the location of TheLid The majority of septic tanks are rectangular in shape and measure around 5 feet by 8 feet. Probe around the tank to identify its boundaries and draw a rectangle around the outside of the tank. The center of a rectangular aseptic tank with a single 24-inch concrete cover erected before to 1975 will be the center of the rectangle. The cost of a standard septic tank replacement lid can range between $30 and $70. Also, do septic tanks have concrete lids, as you may be aware?

While this is a satisfactory installation, many septic specialists recommend that the concrete lids be replaced with plastic risers and lids to provide for easier access to the tank for examining and cleaning.

How to Replace the Lid on a Septic Tank

  1. The first step is to locate the septic tank. To remove and replace the septic tank lid, search for and locate the septic tank. Identify the type of replacement lid that will be required in Step 2. Utilize a measuring tape to decide the size of lid you will want. Most lids are either 21 inches broad or 24 inches wide, so choose wisely. The third step is to remove and reinstall the Lid.

Is it OK to cover the lid of my septic tank with dirt? Some homeowners, on the other hand, may find a pipe orlid in the middle of their lawn to be an eyesore. When dealing with this issue, it is typical to place the riser’s lid a few inches below the surface of the lawn. Thelid can be covered with grass and a thin layer of dirt or another gardening surface in this manner.

Concrete Septic Tank Lid: Sizes, Weight & Cost (Explained)

An underground septic tank is used to store all of the foul-smelling soil that travels through the drain. A concrete septic tank not only removes the obstruction from the drain, but it also helps to maintain our environment clean. For the purpose of inspection and cleaning, a concrete-made septic tank lid is always required for the concrete septic tank to function properly. It also prevents the foul odor that emanates from the tank from reaching its surroundings outside of the tank. As a result, we have included a brief explanation of the sizes, weights, and prices of the concrete septic tank lid in this post.

How big and thick is a concrete septic tank lid?

Depending on the size of the tank, a concrete septic tank lid might be as large as 30 inches. The concrete tank lid can have a thickness of more than 3 inches, and the concrete thickness can range between 3000 and 6000 PSI, depending on the application. If the lid is composed of firm concrete with a high PSI, the thickness of the lid might be greater than 6 inches in some cases. The size of a septic tank lid is typically determined by the size of the actual septic tank. Because the typical dimension of a concrete septic tank is 40 inches by 60 inches, this is the most common configuration.

In addition, the size of the septic tank varies based on the size of the concrete tank used in the system.

Before discussing the thickness of a septic tank lid, it is important to remember that the thickness of the lid is directly proportional to the strength of the concrete.

Hard concrete is defined as having a PSI of 40000 to 60000 and a density of 40000 to 60000. A thicker lid can be used in this situation if the thickness is greater than 5 inches. The thickness of the concrete septic tank is also directly proportional to the size of the tank.

How much does a concrete septic tank lid weigh?

Most of the time, an unpainted concrete septic tank lid weighs between 10 and 12 pounds. The weight of the lid, on the other hand, is determined by the quality of the concrete as well as the strength of the concrete itself. If the primary sewage tank is 5 inches by 7 inches in dimension, a septic tank lid might weigh as much as 15 pounds. It is critical to accurately balance a septic tank lid in order to avoid damage to the tank. This is due to the fact that you will need to lift the septic tank’s cover in order to clean and check it.

Because the thickness of the lid will determine how much weight it will have, the greater the thickness of the lid will be.

If the PSI of the concrete is between 4000 and 6000, the weight of the lid might be greater than 15 pounds.

How much does a concrete septic tank lid cost?

Concrete sewage tank lids are typically priced based on the size of the primary septic tank. The cost of a lid that will precisely cover septic tanks ranging in size from 9000 to 13000 gallons (which is the largest) will be in the neighborhood of $500 or more. The typical size, which is 25 inches in length, will cost around 40 dollars to purchase. According to industry standards, the cost of a concrete septic tank lid is typically determined by the size of the concrete lid. The most expensive concrete septic tank lid is 130 inches in diameter and costs around 500 dollars.

How to build a concrete septic tank lid?

We’ve outlined the quickest and most straightforward procedure for constructing a septic tank cover. The following is a description of the procedure:

Measurement:

First and foremost, you will need to determine the size of the mouth or entrance region of your septic tank, which can be found here. Then, using a measuring tape, you must precisely determine the location of the septic tank’s perimeter.

Build a frame:

The following phase will be to construct a frame that will be based on the same measurement as the septic tank’s mouth. Aluminum or dry wood should be used to construct the frame. However, make certain that the frame is free of the cement once it has dried.

Pour the cement:

You have now finished pouring the cement into the frame. It is important to keep the lid thick enough to be durable and long-lasting, so make sure you keep it at least three inches thick. The surface of the cement must next be smoothed and flattened to complete the process. Check to see that you have used light-duty cement instead of heavy-duty cement.

How many lids should a concrete septic tank have?

Depending on the size of the septic tank, it may require at least two lids. This is because pouring concrete for your septic tank might be a difficult task. When you initially attempt to construct a lid for your concrete septic tank, you should be able to construct at least two lids. The reason for this is that, if you construct two covers for your septic tank, you will have an easier time during the cleaning and inspection processes.

Additionally, if you include two lids to the septic tank, the ventilation system of the septic tank will run more smoothly. The experts so advise that you incorporate at least two lids in your sewage treatment system.

How much does it cost to replace a septic tank lid?

The cost of constructing an average-sized septic tank lid will be around 60 dollars. A septic tank system with two lids will cost between 110 and 120 dollars, depending on how many are included. If you choose the heavy-duty free cement, the price will be somewhat greater than if you do not. Because strong duty-free cement provides a long-lasting and durable finish to the lid. Additionally, the cost of fabricating a custom-sized septic tank lid will be in the neighborhood of $100. To be more specific, it will cost more than 500 dollars to construct the largest possible lid, which is 130 inches in diameter.

How to lift and replace the concrete septic tank lid?

Lifting and replacing a concrete sewage tank lid is far more difficult than installing a new septic tank lid, as you may imagine. As a result, we’ve covered the quickest and most straightforward method of removing and replacing the concrete septic tank lid:

Dig around the lid:

First and foremost, you must excavate around the septic tank. Because it will provide additional room for lifting the lid. In order to dig around the lid, you will need to dig around 15 inches deep. It is preferable if you dig up the area surrounding the septic tank lid that is 15 inches in diameter after the first 15 inches.

Lift up the septic tank lid:

You will need to raise the lid with the assistance of a stout bar or pry bar at this point. Insert the bar between the tank’s lid and the tank’s bottom. You will next need to ask your assistance to lower the opposite end of the bar until it is flush with the ground. Repeat the procedure until the lid of the tank is entirely removed from the entrance of the tank’s opening.

Install the new lid:

It is now necessary to determine the size of the septic tank’s opening. Then you must purchase the lid, making certain that the measurements are accurate. Install the new lid by gently holding it in place with the assistance of your assistant. Finally, place the cover on top of the septic tank and secure it in place.

Can you replace a concrete septic lid with plastic?

If your septic tank requires frequent examination and cleaning, you can opt to replace the concrete septic cover with a plastic one. Because most septic tanks need to be cleaned after 1 to 2 years, they are built with a thick cover to prevent this from happening. If you have a septic tank that has to be cleaned on a regular basis, it is preferable to use plastic covers. However, because plastic lids are easily lifted up, ensure sure the lock system on the plastic lid is functional.

Should septic tank lids be airtight? How to seal a concrete septic tank lid?

Yes, it is vital to seal the septic tank from the outside world. Because it is possible that exterior water will seep into the septic tank. Additionally, if your septic system is placed on top of the soil, it is essential that the septic tank be correctly installed. If this is not done, the tank will overflow due to the exterior water. Although many types of sealant ropes can be used to seal a concrete septic tank lid, the most common one is silicone.

There are several different types of butyl sealants available on the market that may be used to firmly seal the septic tank lid. It is also possible to fill the tank with a thick mixture of mortar and then cover it with heavy plastic to ensure that the lid is properly sealed.

Final thoughts

Septic tank lids are available in a variety of sizes ranging from 25 to 50 inches in diameter. Furthermore, the thickness of a typical-sized lid can reach up to 3 inches. However, the cost of a standard-sized lid is 50 dollars, and it may occasionally be even more expensive than this. In addition, the weight of a 25-inch lid might be as much as 50 pounds in some cases.

See also:  How To Care For Your Septic Tank? (Correct answer)

Tuf-Tite Lids – Septic Tank Lids (Various Sizes)

Tuff TiteLids are a brand of septic tank covers. Please keep in mind that this product does require screws to be used to join the pieces together. You’ll need to acquire stainless steel screws in order to mount them to the wall. You may purchase them at this link. It is necessary to use stainless steel screws since conventional screws will rust as a result of the moisture in your sewage system. Refer to the following list to ensure that you buy the appropriate number of screws. RisersLids = 3 Screws for a 12″ Riser 16″ RisersLids = 4 Screws on each side The number of screws needed for a 20″ RisersLid is 8.

  1. If you are ordering many goods, put the screw amounts together to find the total cost.
  2. (6X3=18) Tuf-Tite manufactures a complete array of Risers and accessories for use in Pre-Cast environments.
  3. Riser Lids are available in two styles: rounded lids or flat lids with molded-in gasket.
  4. Only the color green is allowed.
  5. Make your own concrete lids with the help of the Safety Pan.
  6. Fits a 16 inch waist “Riser Pans, 20″ x 24″ x 4” Only the color green is allowed.
  7. Only the color green is allowed.
  8. Stackable up to six high “a series of increases Available in diameters of 12, 16, 20, and 24 inches.
  9. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 “Tall Riser- This is used for septic tanks.
  10. Only the color green is allowed.
  11. If you are installing a Tuf-Tite riser system, make sure to include all necessary components (which are not shown in the picture).
  • Stainless Steel Screws- The Stainless Steel screws are not included with our risers. You will need to order them separately. In order to guarantee a watertight seal between your risers and the Tank Adapter Ring, you will need to place a ring of butyl rope in between them and underneath them. Tar Screw Kit- This kit is used to attach the Tank Adapter Ring to the top of your tank with tar screws.

Tank Types Express Septic Service

Septic tanks should be cleaned every 3 to 5 years, depending on the size of the household and how much water is used. When the septic tank is pump out on a regular basis, it will help to reduce the buildup of scum and sludge layers in the tank. Ideally, the scum layer should not be more than 24 inches thick. If the material is deeper than 24 inches, it will flow down the outflow pipe and into the drainfield, plugging up the drainfield and resulting in drainfield failure. In order to get your septic tank cleaned, you must first locate the main compartment2nd compartment lid of the septic tank and remove it.

The position of a septic tank lid and the number of lids on a tank varies depending on the year it was placed and the manufacturer.

If you prefer not to find and excavate the Septic Tank lids yourself, or if you are unsure of where the lids are placed, Express Septic Service may assist you with this task.

We may request an as-built drawing from the County Health Department on your behalf if one is available (NO CHARGE). When looking at an as-built, keep in mind that it will only show the overall placement of the sewage system components, not the actual location of the septic tanks.

Septic Diagrams:

1000 Gallon Septic Tanks: This tank design, which was in use from around 1976 to present, will have one main lid and two smaller baffle covers on either end of the tank, as seen in the diagram below.

Two Compartment

From late 1976 until the present, a septic tank layout of 1125-1200 gallons was erected. It is possible for this tank to have two main 24′′ lids or two main lids and two little baffle lids at both ends of the tank right above the inlet and output baffles, depending on the manufacturer. If there are risers to the surface of the tank, you will be searching for two lids that look like this. If the tank is not risered, you will discover concrete lids with a diameter of 2-24″, as seen in the figure below.

Holding Tank

As an alternative to the traditional on-site sewage system, it is a good option. A holding tank is not the same thing as a septic tank. A holding tank is used to retain household waste and prevents any of its contents from leaking into a drainfield, whereas a septic tank is used to enable waste water to flow into a drain field. Concrete, fiberglass, and polyethylene can all be used to construct holding tanks. Depending on the location, holding tanks can be constructed above or below ground. Holding tanks must be pumped on a regular basis, depending on the amount of water and waste water used, as well as the size of the tank.

In the event that a holding tank is not properly pumped, waste water will back up into the home or spill onto the ground.

Pump Tank

Some homes may be equipped with a pump tank or a pump basin in addition to a septic tank. Typically, pump tanks are located underground near the septic tank; however, depending on the year the system was established, risers to the surface may be present, allowing for simple access to examine and repair the effluent pump for maintenance or if the pump has stopped operating. Before the effluent is pumped to the drainfield region, it is collected in a pump tank or basin from a septic tank or ATU (Alternative Treatment Unit).

It is necessary to configure the control floats such that a certain volume of effluent is discharged to the drainfield.

The pump then works to bring the level of wastewater back down until it reaches that of the off float setting.

When the alarm goes off, there is enough reserve storage in the pump tank to allow the homeowner to consume only a little amount of water until the problem with the system can be resolved and the alert turned off.

Aerobic Treatment Unit (ATU)

In some cases, an alternate treatment system may be used in place of a typical septic tank and gravel trenched drainfield, such as in cases of poor soil drainage, small lot size, or environmental concerns. The majority of alternative treatment systems are comprised of a multi compartmented tank known as an Aerobic Treatment Unit, or ATU for short. The majority of ATUs are divided into three compartments: a “waste” compartment, an aeration chamber, and a clarifying chamber. The trash compartment contains solids used in the pretreatment and liquification of garbage, as well as non-waste incidental products that are flushed down the toilet and into the drain.

  1. Clearing the effluent further improves its clarity since the leftover particles are allowed to settle in the clarifying chamber.
  2. These components are intended to kill bacteria and pathogens before the effluent is discharged into the drainfield.
  3. All of these models have undergone extensive testing before being certified.
  4. These can range from gravity to pressure distribution to Glendon mounds to sand filters to drip irrigation.
  5. For any routine operation and maintenance inspections or services, a Health Department Certified Operation and Maintenance Specialist will be required, and some manufacturers may require you to be certified by their firm in order to conduct these services.
  6. As previously said, it is important to have these sorts of systems monitored on a regular basis and fixed as needed in order to maintain correct performance and to keep your system free of problems.

Restaurant Grease Trap

Almost every food service facility that serves food and washes dishes, including restaurants, cafés, coffee shops, delicatessens and bakeries (among others), will have an interior grease trap located near the sinks to collect grease from the sinks. They are available in sizes ranging from 20 to 50 gallons. Fatty acids, oils, and grease (FOG) are prevented from entering your drain pipe by a grease trap, which is a chambered compartment.

Grease flows into the trap, enabling the grease to solidify and float to the top of the trap while weighted solids fall to the bottom of the trap, allowing the liquid to flow out via the drain pipes and into the septic tank or into the city sewage.

Grease Tank Interceptor Service

A grease interceptor is a huge tank that may be situated outside of the structure on the ground level. They can range in size from a few hundred gallons to several thousand gallons. You will need two tanks if you have an exterior tank. The first tank will be a grease trap (tank), which will hold grease until it is removed. The garbage from the restrooms will be disposed of in a tank that is specifically dedicated for this purpose; if the facility is on sewer, the waste will be disposed of in the city sewage.

In addition to a simple cleaning rooter service utilizing an electric snake, we also provide hydro-jetting, which uses high pressure water to break away hardened grease and keep the drain from backing up.

Septic Tank Risers, Lids, and Covers

Septic tank risers are intended to replace existing concrete, fiberglass, or metal septic tank lids by lowering the entrance to the ground level and allowing for better drainage. Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water? Do you despise having to lift and carry incredibly big concrete lids on your shoulders? It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.

  1. With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!
  2. Want to stop digging up your yard every time you need to have your septic system cleaned, repaired, or re-filled with water?
  3. It appears that you require septic tank risers to raise your access to ground level, as well as a lightweight, easily removable access cover.
  4. With the Polylok risers and lids from Septic Solutions, septic tank maintenance will be a breeze!

FREQUENTLY ASKED QUESTIONS

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered! Would the POLYLOK SEPTIC TANK LID fit directly on the ADAPTER RING, or will I need to use a RISER to ensure a proper fit on the tank? With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength.

  • Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter.
  • ALL other Polylok lids will attach straight to the adapter ring, eliminating the need for a riser or any other adaptor.
  • No.
  • Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.
  • It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade.
  • IS IT BETTER TO USE THE STANDARD LID OR THE HEAVY DUTY LID?
  • If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended.
  • Yes.

IS IT INCLUDED WITH THE POLYLOK SEPTIC TANK RISERS AND LIDS TO USE SCREWS? Yes. The Polylok Septic Tank Risers are assembled using stainless steel screws that allow them to be connected to one another. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].

THE POLYLOK SEPTIC TANK RISER ADVANTAGE

Riser systems are available in a variety of shapes, sizes, and designs on the market today. The Polylok septic tank risers are, without a doubt, the best money can buy in this category. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

The Polylok risers are reinforced with structural ribs that run internally around each riser segment, providing them with exceptional strength and allowing them to maintain their shape even after the hole is backfilled with dirt. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

LOW PROFILE RISER LIDS WITH HANDLES

The septic tank access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise serviced. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

See also:  Why Is Extra Water In Septic Tank. Near The Drain? (Correct answer)

LARGE TANK ADAPTER RING

It is necessary to use an adapter ring in order to attach risers to your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

STAINLESS STEEL SCREWS INCLUDED

At Septic Solutions, we strive to make the buying and installation process as simple as possible for our customers. All of our Polylok risers and lids are delivered with all of the stainless steel screws required for installation in one package.

Septic Tanks Risers- Bring Your Access To Ground Level

Getting a little tired of having to dig up your yard every time your septic tank has to be pumped out or serviced? Are you getting tired of dealing with incredibly hefty concrete lids? It appears that you are in need of septic tank risers in order to bring your access down to ground level!

Our septic tank risers and covers are constructed of high-quality, heavy-duty polyethylene plastic, which makes them extremely sturdy and durable while also being lightweight and simple to handle.

THE POLYLOK ADVANTAGE

Septic tank risers are available in a variety of shapes, sizes, and designs on the current market. We believe our Polylok septic tank risers are the best money can buy in terms of quality. There are several causes for this, but the following are the most significant:

FACTORY INSTALLED GASKETS

The Polylok brand is the only one on the market that is sent to you from the factory with gaskets already in place, making it unique. This means that there is no further work necessary to ensure that the riser system is air and water tight! Keep ground water out of your tank, wastewater in your tank, and potentially hazardous gases out of your yard! In contrast to most other products, our Polylok septic tank risers do not require you to purchase or use any other type of sealant between each riser part.

INTERNAL STRUCTURAL RIBS

Once the hole has been backfilled, the structural ribs in the Polylok septic tank risers are inserted inside around each riser piece, providing them with tremendous strength and allowing them to maintain their shape under the pressure of the earth being pressed on them. As a result of the freezing and thawing of the ground in many parts of the country, it is necessary to have a smooth surface on the outside of the riser’s exterior. It is possible for items that have structural support on the outside of the riser to actually be lifted from the tank, causing damage to both the riser and seal, during periods of freezing and thawing.

LIDS WITH HANDLES

The access lid on a riser system is one of the most significant components since it is the part of the system that is visible from the outside and that must be removed every time the system is pumped or otherwise maintained. The Polylok lids are pre-installed with handles, which make it simple to remove the lid whenever you need to get access to the system or to replace it. The bottom of the lids is structurally supported, which allows them to remain relatively flat rather than domed in shape, as is the case with many other items on the market.

LARGE ADAPTER RING

An adapter ring is required in order to properly install septic tank risers on your septic tank. We have one of the largest adapter rings available on the market, allowing you to cover up to a 25″ square or 27″ circular aperture with a Polylok adapter ring. This ring fits both 20″ and 24″ risers, allowing you to have a great deal of versatility no matter what size your opening happens to be!

GET OUT YOUR MEASURING STICK!

A few measures must be taken before purchasing a septic tank riser system in order to ensure proper installation. The first thing to consider is the size of your opening. Take a measurement of the aperture in your septic tank at its widest point to determine the size of your tank. Instead than measuring the present lid, it’s critical to measure the opening. Because you will be removing the present cover, the measurements of the lid are no longer important and may differ from the size of the aperture itself.

The second measurement will be the distance between the top of the septic tank and the surface of the ground. You are now prepared to make a purchase based on these two measures!

THE COMPLETE RISER SYSTEM

We have a large selection of components from which you may pick to create your own own full riser system. Our many various options offer our product the adaptability to be utilized in virtually any application, but they may also be a bit daunting when attempting to pick which components to buy for a certain application. Each component is discussed in further depth below.

ADAPTER RINGS

The adapter ring is the first component that you’ll need to put together in order to assemble a full riser system. The adapter ring attaches directly to the septic tank, allowing the risers to stack, lock, and mount to it without the need for any additional hardware. Having this component is critical since the risers are not flat on the bottom because they are meant to be stackable, and it is not feasible to install them straight to the septic tank without this piece. The adapter ring provides the flat surface you need to mount to the tank while also being able to accommodate the stackable risers that are included with the tank.

Our square tank adapter ring can accommodate big square apertures up to 25 inches in diameter and large round openings up to 27 inches in diameter.

They are intended to be used with openings that are 24″ or less in diameter.

Concrete anchors, a masonry bit for installing the anchors, and butyl sealer are all included in this set.

RISERS

Following your selection of the adapter ring, it is time to go shopping for risers. The Polylok risers are available in two heights: 6″ and 12″, as well as in two diameters: 24″ and 20″. Stackable, each unit has a gasket that has been fitted as well as stainless steel screws to allow for easy installation. Determine which risers will work best for your application based on the height measurement you made between the septic tank and ground level.

OPTIONAL SAFETY SCREEN

In addition to the 20″ and 24″ riser systems, Polylok also produces safety screens that fit within the riser systems. These screens serve as a supplementary layer of protection in the event that the riser cover is unintentionally damaged or removed, and they keep foreign objects from entering the septic tank. They also keep dogs from slipping into unprotected septic tank openings!

RISER LIDS

You will require a lid to complete your riser system, which is the final component you will require. Both the 20″ and 24″ riser systems may be used with the Polylok lids, which are available in two different types to suit your needs. For ease of access, the basic lid is equipped with handles and a gasket that has been factory placed, as well as stainless steel screws to keep it in place. These lids are strong enough to withstand foot traffic as well as the weight of a riding lawn mower driving across them.

Stainless steel screws are included for installation.

Installations below grade or in regions with a high volume of foot traffic are advised for the heavy-duty lids.

The shipping of these items in large boxes necessitates the addition of additional time, materials, and UPS shipping fees.

SIMPLY ADD THE ITEMS TO YOUR SHOPPING CART AND THEN CHECK YOUR SHIPPING COST. If you place your order before 2 PM CST, you will be able to get your order sent the same day you placed it.

FREQUENTLY ASKED QUESTIONS

The following are some of the most commonly asked inquiries that our customer support representatives are asked. Take a peek below; it’s possible that the queries you have have been answered!

WILL THE LID FIT DIRECTLY ON THE ADAPTER RING OR DO I NEED TO USE A RISER?

With the exception of the 24″ Heavy Duty Lid, the lid will often fit straight onto the adapter rings in the majority of cases. The underside of the 24″ Heavy Duty Lid is strengthened for added strength. The height of this reinforcement is actually more than the height of the adapter ring. Therefore, the 24″ Heavy Duty Lid will only be able to be used without using an adapter when the opening is at least 24″ in diameter. The lid will not fit through any aperture less than 24 inches in diameter.

CAN I CUT THE RISER SYSTEM DOWN TO A SPECIFIC HEIGHT?

No, the Polylok riser system is available in increments of 6″ and 12″, and it cannot be customized to a certain height. Cutting the riser will result in the lid not being adequately secured on the riser that has been cut down.

DO I BRING THE RISER SYSTEM JUST BELOW, AT, OR ABOVE GRADE?

It is entirely up to you whether you want to bring the riser system up to grade, raise it above grade, or leave it slightly below grade. Because the riser system is airtight and watertight, there is no danger in moving it up to or above grade level.

SHOULD I USE THE STANDARD OR THE HEAVY DUTY LID?

The regular lid is sturdy enough to withstand foot activity and weights up to the weight of a small riding lawn mower passing over it without bending or breaking. If the riser system is located in a high traffic location or is going to be run over by lawn equipment on a frequent basis, the heavy duty lid is recommended. If you have any more queries, please contact us at 1-877-925-5132 or [email protected].

Common Septic Tank Facts

Septic systems are a low-cost and frequently successful alternative to conventional sewer systems. Concrete tanks have been the most frequent since the 1940s, with 3 – 500lids for a 1000 gallon tank and 4 – 500lids for a 1500 gallon tank being the most typical. Tanks began to be equipped with 16″ square concrete plugs with a lifting bail in the late 1990s, allowing for easier access to both sides of the tank. Many tanks today are made of fiberglass or plastic. Over time, the concrete might degrade, and the lids may develop cracks or possibly shatter completely due to the pressure.

  • Even broken lids should be replaced for the sake of the public’s safety.
  • They get access to your septic tank by removing green covers that are 20 inches in diameter.
  • This is done in order to prevent anyone, especially children, from removing a lid and falling into the container.
  • A typical water level for a tank should be 6″ below the top of the tank, and the tank should be kept completely filled at all times.
  • The level of the water is often a good sign of potential problems.
  • Additionally, it might suggest a clogged intake line, which could be caused by roots, a damaged pipe, or a loose joint.
  • If there has been a lot of rain, the earth may get saturated, making it impossible for any additional water to seep through the soil to the surface.
  • If your tank has allowed particles to enter the field lines, this might cause the openings in the corrugated pipe to get clogged, preventing water from percolating through the soil as effectively as it should be.

An output filter may be placed to prevent particulates from entering the field lines, but it would need to be cleaned on an annual basis to ensure that this does not happen. Nonetheless, it is far less expensive than rebuilding field lines.

How to Find Your Septic Tank

Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.

5 Ways to Find Your Septic Tank

1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.

  • 3.
  • Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
  • Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
  • When you do, that’s when your septic tank comes into play!
  • Look for the Lid.
  • You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
  • Those areas should be excavated in order to disclose the lids.
  • Get in touch with the pros.
  • Lifting concrete lids will necessitate the use of specialized equipment.
  • A fall into an unprotected septic tank has the potential to be lethal.
  • Produce your own diagram of your yard, which you may file away with your other important house paperwork.

That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!

How to Find Your Septic Tank Lid

Previous PostNext PostWhether you realize it or not, it is critical that you be aware of the position of your septic tank lid and the septic tank itself. Despite the fact that septic tanks are fairly huge, they can be difficult to identify, particularly if they have not been properly maintained over time. Continue reading to find out how to locate your septic tank lid.

See also:  What Will Dissolve Grease In Septic Tank? (Best solution)

Why It’s Good to Know Where to Find Your Septic Tank Lid

Knowing the location of your septic tank is a fantastic approach to spot septic tank problems as soon as they occur. Consider the following scenario: If you saw water near your septic tank lid, you would know right away that you could have a problem with your system being overloaded with waste. Furthermore, by understanding where your septic tank is located, you may avoid parking cars on top of it, which might cause the tank to collapse and create flooding. You’ll also be able to point service personnel in the right direction for septic tank services, which will eventually save them time and money while also saving you money.

How to Find Your Septic Tank Opening

Knowing how critical it is to know where your septic tank lid is located, it’s time to go out and find one for yourself. Keep an eye out for a circular lid that is roughly two feet in diameter during your quest. Septic tank lids are normally constructed of green or black plastic, however they can occasionally be made of concrete. It is not always simple to locate the septic tank lid, however, because untidy vegetation, mud, or debris might obscure the lid’s location. If you live in a snowy climate, seek for a spot of lawn where the snow melts more quickly than it does anywhere else on the property.

How to Find Your Septic Tank Lid as a New Homeowner

During the process of purchasing your house, you should have been provided with a map of your property that showed the location of your septic tank. This is normally included as a part of your home inspection service package. All you have to do from there is compare the diagram to your land, find the septic tank location, and potentially dig around it to check whether the lid has been hidden by vegetation or other obstructions. People have been known to place an object such as a huge rock on top of the septic lid, so be sure to look beneath landscaping stones as well.

How to Find Your Septic Tank Lid as an Existing Homeowner

Still having trouble locating your septic tank lid? There’s a significant probability it’ll end up in the ground. The pipes coming from your basement should be followed, as they will take you in the direction of your septic system, which is what we propose. You may identify the lid of your septic tank by prodding the ground every few feet with a metal probe once you’ve determined the direction. Once you’ve determined the direction, search for any high or low points in the yard that could suggest where your septic tank could be located.

You can also use a metal detector to locate your lid since most lids include a metal handle or clip to hold the lid closed.

Another reason you might not be able to locate your lid is the depth to which it was buried. The majority of lids are buried up to a foot deep, but some lids might be buried as deep as four feet in extreme cases! In some instances, a professional with specialized locating equipment may be required.

How to Maintain Your Septic Tank Lid

Following the discovery of your septic tank lid, keep it in good condition to avoid damage and ensure simple access for future septic tank maintenance, such as pumping your septic tank every three- to five-year period. Here are some pointers for keeping your septic tank lid in good working order:

  • Keeping the grass around the septic tank lid regularly mowed is important. Remove any dirt or debris that may have accumulated on your septic tank lid
  • Mark the area to ensure that no one parks or constructs structures there. It is possible to do this using a flag, garden décor, or ornamental pebbles.

Professional Septic Tank Services

Is it difficult to find trustworthy septic tank services or septic tank installation? If you are looking for septic tank installation, inspection, and cleaning services, check with your local Mr. Rooter ® Plumbing franchise. Mr. Rooter charges a set amount up front, with no overtime fees or additional expenses. To get started, call us at (855) 982-2028 or fill out our online estimate request form. Is the lid of your septic tank obscured by grass? Inquire with The Grounds Guys about routine lawn care and upkeep.

Rooter, is a member of Neighborly’s network of dependable home service experts, which includes Mr.

By hiring The Grounds Guys to provide trustworthy grass mowing and landscape care services, you can be assured that your septic tank lid will always be simple to locate.

How Far Apart Are Septic Tank Lids? (Find Out Now!)

If homeowners wish to keep their septic tanks in excellent working order, they must educate themselves and use caution when doing so. The information you possess may be able to avoid your family’s septic tank from suffering unneeded harm. The distance between the lids of your septic tank is one of the important details to understand. The placement of a septic tank’s lid varies depending on the tank’s size and kind. You’ll discover that there are a number of elements that play a role in determining where the lids are placed.

According to general rule, the space between the lids gets longer as the size of the tank gets larger.

Knowing more about your septic tank, as well as its lids, will assist you in providing better maintenance for them.

The Importance of Knowing the Distance between the Septic Tank’s Lids

You might be asking why it’s vital to be aware of the septic tank’s lids in the first place. Is it really important to know where the septic tank lids are or how far apart they are in the end? It is correct that knowing the answers to such questions will be beneficial in the long term. There are two primary reasons why homeowners should become more knowledgeable about septic tank lids. For starters, you will be unable to accomplish much with your yard if you do not know where the septic tank lids are located.

  • It is impossible to be casual with them and expect them to remain in good condition.
  • If you continue to make this error, it will only be a matter of time until the lids begin to fracture.
  • Even if you are able to identify the broken lids early on, you will still be responsible for the cost of replacements.
  • Homeowners should also pay attention to the lids, since they are frequently the first to indicate that a problem with the septic tank has occurred.
  • If the septic tank is overflowing or obstructed, foul odors may begin to seep out through the lids and into the surrounding area.

Beyond the aforementioned reasons, the pros you employ will also want to know how far away the lids are from one another, if at all possible. Having an understanding of the distance between the lids will help them to do their duties more effectively,

What Is the Distance between the Septic Tank Lids?

Septic tank lid spacing is not established at a certain distance apart. A significant factor in determining how far apart the lids should be spaced is the size of the tank itself. Septic tanks having a capacity of 1000 gallons or more are often equipped with lids that are six feet apart. There are also some 1000-gallon tanks with lids that are six and a half or even seven feet apart from one another on the market. Due to the widespread usage of 1000-gallon tanks in residences, it is possible that the tanks built on your property will have lids that are divided in this manner as well.

1500-gallon tanks with lids that are approximately eight feet apart are available for purchase.

Smaller septic tanks, on the other hand, tend to have lids that are closer between than their larger counterparts.

How Many Lids Does a Septic Tank Have?

Walking around your yard, you may see that there are a few moist areas that have developed. You’re probably expecting to see one or two damp patches, but you could notice a lot more than you think. Modern septic tanks are equipped with many lids. Modern septic tanks are required to have a minimum of two covers. However, there are still tanks that employ three or more cylinders. Furthermore, there is a possibility that your septic tank has only one cover. Before 1975, all of the tanks that were built and installed employed simply a single cover to keep the water in.

How Far Deep into the Ground Are the Septic Tank Lids?

It is also important for homeowners to be aware of how far down their septic tanks’ lids are buried. If you intend to inspect your septic tank on your own, you should be aware of the following information. Digging too far into the earth and damaging the lid is not something you want to happen inadvertently. The majority of septic tank lids are buried between four inches and four feet deep into the earth, depending on the model. Beginning with cautious, deliberate digging to avoid putting the sharp point of the shovel into the lid, If you want to limit the likelihood of harming the septic tank’s lid even more, you may install probes in it.

In addition, they can tell you if there is something substantial down there that you should avoid striking.

How Big Are the Septic Tank’s Lids?

Additionally, because of their size, the lids of septic tanks must be removed and stored separately. It is possible for a single septic tank lid to be as large as 24 inches in diameter. Even the smallest lids will reach a height of almost 20 inches. The lids that are used to keep septic tanks closed are also on the thicker side. Given the size of septic tank lids, working with them on your own is not suggested due to their thickness of three to four inches. They can be difficult to handle, and if you are not careful, you could damage yourself.

If you need to remove or replace the tank’s lid, you should consider contacting a professional to assist you. Instead of spending money on expert assistance, have a buddy over who can assist you with the cover and other tasks.

What Is the Right Way to Maintain a Septic Tank’s Lid?

The lids of the septic tank are probably the least complicated to maintain when compared to the other components. The first step is to make sure that the lid is not bearing an excessive amount of weight. It is important to avoid driving over the location where the lid is located on the vehicle. It’s also a good idea to avoid putting heavy fixtures on top of the lid. Some tiny ornamental components are OK, but larger items such as fountains or flowerbeds should be placed in a different location.

  • You don’t want any debris to go inside the container and maybe compromise the seal of the lid.
  • If the grass blades are beginning to grow too tall or if they are beginning to encroach on the lid, they should be cut back.
  • It is recommended that you check on them every few months or so to see whether they have suffered any harm.
  • However, if you have any reason to believe that the lid has been damaged, you should get it examined by a specialist.

How Do You Secure Septic Tank Lids?

You don’t want anyone tampering with the cover of your septic tank. Consider using nuts or screws to reinforce the lid to keep this from happening in the first place. In order to ensure that only you have access to the container, a lock can be attached to the lid.

Do You Need to Seal Your Septic Tank’s Lid?

The lid of the septic tank must be properly sealed at all times. The absence of a tight seal around the perimeter of the lid may allow a wide variety of debris to enter the tank and cause it to overflow. The act of creating a seal around the lid also helps to keep rainwater out while it’s pouring outside. Creating that barrier also prevents unpleasant odors from leaking from the septic tank during the cleaning process. It is possible to use mortar mix to create a tight seal along the opening of the tank and the lid’s opening.

Leave a Comment

Your email address will not be published. Required fields are marked *