Where Is The Diverter Valve On A Septic Tank? (Question)

How do you repair a septic tank?

  • To repair a leach field, restore the septic tank to reduce the load on it, decrease the amount of waste put in the tank, avoid excessive wetting of the soil close to the field, and make a separate drain field for wash water. In addition, drain water from the septic tank, and remove any debris from the pipelines of the field regularly.

How do I find my septic diverter?

The D-box will at or near end of the drainfield area that is closest to the septic tank. Look at the site layout for where the D-box could possibly be located. For example, if the drainfield site is level and rectangular, the D-box would typically be at or near the edge of the drainfield closest to the septic tank.

Do septic systems have backflow valves?

If a septic system is located in a flood-prone area, a plumber should install a backflow preventer on the building sewer so sewage cannot back up into the home during a flood. A backflow preventer is recommended, as a simple check valve may not close properly and sewage may back up into the home.

Why is my septic tank overflowing outside?

This type of overflow is usually caused by either poor design or damaged drain pipes. If tree roots grow through pipes, the walls of the pipe could collapse and prevent proper drainage. Clogged or broken pipes can also cause overflow. Some septic system overflow happens because of improper design.

How do you find a metal detector with a septic tank?

6 Steps to Locate a Septic Tank

  1. Find Your Main Sewer Drain Line. Sewage from your toilets, sinks, and showers collects into a main drain line.
  2. Check Permits and Public Records.
  3. Determine Septic Tank Material.
  4. Time to Dig.
  5. Mark the Location for Future Maintenance.

Where is the distribution box on a septic tank?

If your layout consists of a rectangular and level drain site, your distribution box is likely to be located near the edge of the drain field, closest to the septic tank. You can also look for a depression in the ground between the septic tank and drain field a couple of feet in diameter.

Do I need a backwater valve on a septic tank?

Fact. – backflow valves or back flow preventers are not to be installed on septic systems because oxygen is required. Oxygen from the interior plumbing vent on your roof, commonly known as the “stink pipe”, needs to make it’s way into the tank to relieve methane and hydrogen sulfide gases.

Why does my septic tank overflow when it rains?

As rainwater floods over your drain field, the effluent from the septic tank will have no place to drain because the ground under the drain field is already saturated with water. As a consequence, the wastewater will back up in the tank and overflow in the leachfield.

Why is my septic backing up into my house?

Drains can become blocked with sludge, roots and dirt from broken pipes. In addition, if the ground is saturated because of high water table or heavy rainfall, then the septic tank will not drain and it will back up into the house.

How do u know when your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

  1. Your Drains Are Taking Forever.
  2. Standing Water Over Your Septic Tank.
  3. Bad Smells Coming From Your Yard.
  4. You Hear Gurgling Water.
  5. You Have A Sewage Backup.
  6. How often should you empty your septic tank?

Can I shower if my septic tank is full?

Only the water would get out into the leach field in a proper system unless you run too much water too fast. The thing to do is to run your shower water outside into it’s own drain area, but it may not be allowed where you are. Used to be called gray water system.

Will a flooded septic tank fix itself?

Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.

What to do if your septic tank is overflowing?

4 Things to Do When Your Septic Tank Is Flooded

  1. Check the Groundwater Level. Drainfields for septic tanks are normally between 2 to 4 feet from the top of the soil.
  2. Wait to Pump Until the Ground Dries.
  3. Reduce Water Sent Down the Drain.
  4. Make Changes to Help Your Newly Pumped Septic System.

Will toilet flush if septic tank is full?

A common indicator of septic tank problems is a toilet that’s slow to flush — or won’t flush at all — and a plunger can’t fix the issue. The tank may be full, or there could be a clog in the pipes.

How do I know if my drain field is failing?

The following are a few common signs of leach field failure:

  1. Grass over leach field is greener than the rest of the yard.
  2. The surrounding area is wet, mushy, or even has standing water.
  3. Sewage odors around drains, tank, or leach field.
  4. Slow running drains or backed up plumbing.

Add a Diverter Valve for a Septic Tank

It is used in a septic system to redirect waste from one drain field to another by opening and closing the diverter valve. When applied to this case, the principles of a diverter valve are quite similar to those of a diverter valve that is commonly seen in typical household applications such as showerheads. For those who have more than one drain field or leech field, you may want to think about upgrading your existing septic system to include a diverter valve. The steps to complete this project are outlined in the next section.

Step 1 – Turn off Electricity

Remove all power from the entire house. To accomplish this, either turn off the primary power source on the circuit breaker panel or separate the fuse box from the main power source. You should never perform any sort of septic repair or addition without first cutting down the electricity to the system.

Step 2 – Get Prepared

Put on an old set of clothing or a pair of labor clothes. Put on a pair of rubber gardening gloves and a pair of goggles to protect your eyes from the sun. When you install a diverter valve, it may be a dirty process since you never know what kind of waste you will come up against.

Step 3 – Locate the Septic Tank Piping

Put on an old set of clothing or a pair of labor clothes. Put on a pair of rubber gardening gloves and a pair of goggles to protect your eyes from the sun. When you install a diverter valve, it may be a dirty process since you never know what kind of waste you will come up against.

Step 4 – Remove Piping

Put on an old set of clothing or a pair of labor clothes. Put on a pair of rubber gardening gloves and a pair of goggles to protect your eyes from the sun. When you install a diverter valve, it may be a dirty process since you never know what kind of waste you will come up against.

Step 5 – Add the Diverter

Incorporate the diverter into your septic system’s pump by screwing it in place. With a wrench, tighten the diverter valve until it is completely closed. A clamp should be installed on the diverter valve, especially where it meets the septic system.

Step 6 – Add the Piping

Incorporate the diverter into your septic system’s pump by screwing it in place. With a wrench, tighten the diverter valve until it is completely closed. A clamp should be installed on the diverter valve, especially where it meets the septic system.

Step 7 – Close the System

Change the direction of the diverter valve to the desired setting (pick any of the two or three locations). Close the septic tank’s lid and the tank itself.

Step 8 – Turn on Electricity

Return to the electrical panel and switch on the power to the entire home once more.

Step 9 – Check System

Check on the system on a regular basis during the following few of days to ensure that it is running properly.

Flow director valve tee splits effluent 50/50 or can direct 100% in one direction

The four inch flow director splitter valve includes an adjustable handle, a riser, a coupler, and a four inch threaded access cap in addition to the valve. The’versa-tee’ is equipped with special staggered hub fittings that allow it to handle PVC or ABS pipe up to 4 inches in diameter in both Sch40 and thin wall SDR35 sewage drain pipe. Please take note that there is a two-inch elevation difference between the intake pipe (base of tee) and two output pipes (top of tee) where the effluent flow divides.

  • It is possible to let one half of your leachfield to go fallow for a few months in order to refresh the soil, prevent overloading and decrease the formation of bio-matting with the use of a diverter.
  • Then there’s the possibility of allowing a quarter of the leachfield to go dry on a seasonal basis.
  • This is not a gate valve, but rather an internal weir that separates the flow.
  • When dealing with pressurized or siphon effluent systems, two gate valves and a tee manifold should be used instead of a director valve.
  • Director Valve Kits are delivered in the condition depicted, including a four-inch threaded access cap, riser pipe, coupler, and the adjustment handle.
  • Because it is not a pressured fitting, the “Versa-tee” may accommodate pipe with a diameter of 4 inches (Sch40 or SDR35) and can be used with ABS or PVC.
  • The item is in stock and will be shipped on the following business day.
See also:  What Would Make You Smell Septic Tank Or Sewer When It Rains? (Best solution)

Even little deviations in the level of distribution boxes and basic tee connections (as little as 1/8 inch) will result in a much less than equal 50/50 split.

Because the housing of the flow diverter distribution valve is made of ABS plastic, it is always best to use multi-purpose cement when attaching it to PVC pipe.

Directions for operating flow directer splitter valve Turn the handle to the left while standing at the inlet side of the tee (bottom of image), facing the two outlet pipes.

Handle rotates around 270 degrees, rather of the full 360 degrees, with a 50/50 flow split anywhere in the middle of the handle.

New rotational movement is somewhat sloppy, but it becomes more firm with continued usage.

For the sake of clarity, the housing tee is depicted in white above.

As a result, while connecting PVC pipe, multi-purpose cement should be used.

When it comes to septic and greywater systems, even effluent distribution is crucial for soil health.

Minor settling with a D-box or tee fitting manifold has a significant impact on the equitable distribution of the product.

One of the most important factors in extending the life of a septic or greywater system’s leach field is to maintain a healthy soil culture.

In addition, at the end of each run, you should always vent.

For many weeks, allowing a portion of your leach field to “fallow” and dry will provide the soil with an opportunity to dry and regenerate.

Constantly saturating a leach field trench with sewage effluent throughout the year leads to the development of an unhealthy sodden anaerobic (no oxygen) soil culture, which finally causes the trench to clog prematurely, culminating in leach field failure.

Septic drain field diverter valve stuck

It includes an adjustment handle, a riser, a coupler, and a four-inch threaded access cap in addition to the flow director splitter valve. The’versa-tee’ is equipped with special staggered hub fittings that allow it to handle PVC or ABS pipe up to 4 inches in diameter in both Sch40 and thin wall SDR35 sewer drain pipe configuration. Please take note that there is a two-inch elevation difference between the intake pipe (base of tee) and two output pipes (top of tee) where the effluent flow is separated.

  1. For a few months, a diverter permits one half of your septic system leachfield to be left fallow in order to rejuvenate the soil, minimize overloading, and slow the establishment of bio-matting.
  2. If you want to dry out a quarter of the leachfield on a seasonal basis, you may do that.
  3. This is not a gate valve, but rather an internal weir that separates the flow of fluid.
  4. In pressurized or siphon effluent systems, two gate valves and a tee manifold should be used instead of a director valve.
  5. Director Valve Kits are delivered in the manner depicted, and include a four-inch threaded access cap, riser pipe, coupler, and the adjustment handle.
  6. As a result of the fact that it is not a pressured fitting, the “Versa-tee” may accommodate pipe with a 4 inch diameter Sch40 or SDR35 and be utilized with ABS or PVC.
  7. Available for immediate shipment the following business day after purchase.

In the case of distribution boxes and basic tee fittings that are off-level by even a fraction of an inch, the 50/50 split will be significantly less than equal.

It is recommended that you use multi-purpose cement when attaching the flow diverter distribution valve to PVC pipe since the housing is made of ABS plastic.

Instructions for using a flow director splitter valve are provided.

This will direct all of the water to the right fork.

Checking the direction of the flow is easy since you can look down the riser assembly.

If the valve ever becomes too stiff to adjust readily, avoid pressing the handle and instead pour a pail of hot soapy water down the stand pipe to soften up the action, as seen in the video.

Not PVC, but a black ABS plastic material instead.

Prior to solvent welding with the multi-purpose cement, prime all seams with purple primer to ensure that they are completely waterproof.

Distribution boxes are notoriously unreliable, so don’t put your faith in them!

The variation in effluent distribution to several leach field lines caused by being out of level by as little as 1/8 of an inch can be significant.

Before constructing leach chambers or perforated pipe-in-gravel leach field lines, loosen the soil (scarify) twelve inches below the bottom of the trench and allow it to drain.

In order to ensure that one flow is always turned off and allowed to dry up for at least a couple of months at a time, you should rotate sewage effluent to your trenches (or pits) on a periodic basis.

Decomposition of organic matter occurs naturally in the soil when aerobic bacteria take control and decompose organic matter, avoiding the formation of bio-mat.

Constantly saturating a leach field trench with sewage effluent throughout the year leads to the development of an unhealthy sodden anaerobic (no oxygen) soil culture, which finally causes the leach field to collapse prematurely.

Using the flow diversion valve on a septic tank. (tanks, drain, installed) – House -remodeling, decorating, construction, energy use, kitchen, bathroom, bedroom, building, rooms

Please registerto participate in our discussions with 2 million other members – it’s free and quick! Some forums can only be seen by registered members. After youcreate your account, you’ll be able to customize options and access all our 15,000 new posts/day with fewer ads.

Hi:I need to turn the flow diversion valve on my septic tank so it uses the second drain field, but the septic tank company is charging me $200 to come and do this. I know where the valve is and I also have the rod for turning it, but I have no idea how to do it. The septic tank company said if I don’t do it correctly, I could end up breaking the valve so I should call them the first time and they can show it to me.Any suggestions? I did not find any directions on the internet.Regards,K
Probably a ball valve.


Most of those things are a ball type valve. You turn it to the left or counter clockwise to open it. Turn it 90 degrees or 1/4 quarter turn only. It should have a built in stop, if you keep applying pressure it can break.Most of those deals the rod has a square hole in the socket at the end, you look down in there with a strong flashlight, then feel around to get the socket on the valve stem and then turn it one quarter turn counter clockwise to open it. Of course the opposite direction will close it.Depending on the situation, the valve typically will have an indictor to show if it is open or closed. Pointing down the pipe it is open, pointing across the pipe direction it is closed. Being a septic system, valve should not be that deep. Try to see it first with a good light. With those type valves if you are not sure of the position, you try both ways with very light pressure until it moves one way or the other. Septic application you expect it to be a PVC ball valve. Once the valve is opened there is zero restriction in terms of flow thru the valve. Just a ball with a hole thru it, in open position, nothing in the flow path, closed the undrilled part of the ball totally blocks the flowpath. Just remember it only requires a quarter of a turn. The strange one might be a gate valve and that requires a bunch of turns to get it open but you probably got a cheap ball valve. Use the eyeballs first.Gees $200 bucks to open a valve, how do I get in that business?

Location: Houston, Texas10,440 posts, read47,552,871timesReputation: 10550
Quote:Originally Posted byCosmicMost of those things are a ball type valve. You turn it to the left or counter clockwise to open it. Turn it 90 degrees or 1/4 quarter turn only. It should have a built in stop, if you keep applying pressure it can break.Most of those deals the rod has a square hole in the socket at the end, you look down in there with a strong flashlight, then feel around to get the socket on the valve stem and then turn it one quarter turn counter clockwise to open it. Of course the opposite direction will close it.Depending on the situation, the valve typically will have an indictor to show if it is open or closed. Pointing down the pipe it is open, pointing across the pipe direction it is closed. Being a septic system, valve should not be that deep. Try to see it first with a good light. With those type valves if you are not sure of the position, you try both ways with very light pressure until it moves one way or the other. Septic application you expect it to be a PVC ball valve. Once the valve is opened there is zero restriction in terms of flow thru the valve. Just a ball with a hole thru it, in open position, nothing in the flow path, closed the undrilled part of the ball totally blocks the flowpath. Just remember it only requires a quarter of a turn. The strange one might be a gate valve and that requires a bunch of turns to get it open but you probably got a cheap ball valve. Use the eyeballs first.Gees $200 bucks to open a valve, how do I get in that business?You ain’t kidding bout that.
Location: Apple Valley Calif7,474 posts, read21,803,056timesReputation: 5651
It doesn’t cost $200 to open a valve, it cost $200 for him to come to your house. He opens the valve for free.!
Location: Houston, Texas10,440 posts, read47,552,871timesReputation: 10550
Yea but $200 for a house call is more then a Doctor would charge. Oops I forgot, Plumbers charge more then Doctors. That defies logic but it’s true.
Sewer water in my septic tank diversion valve access pipe


Hi – I went to turn my septic tank diversion valve a few days ago and for the first time in ten years found about 6 inches of “effluent” at the bottom of the access pipe where the valve stem is. I turned the diversion valve stem but the effluent has not gone down.How did effluent get into the access pipe? And do I have a leaching problem (or some other type of problem) with one of my dual tanks?

Septic valve


Hi:I am having some issues with my septic tank. We installed a new pump approx. 3 months ago and everything has worked fine until early this week. The pump still works fine and pumps out large amounts of water. However, the water level in the tank doesnt go down. I found a valve approx. 35 feet away from the tank. The valve was closed for some reason. I figured that was our problem so we opened the valve but the water level still doesnt go down. Its the like the water being pumped doesnt have any where to go. We have tried snaking the 2in pipe and it goes through with no problems. Any suggestions on why the water level does not drop? Please help, Im about out of ideas.

I have a question about my septic tank. My father accidently backed the rv into another pipe that broke the velve. Its still in place. It basically cracked. My father is out of town and I needed to relocate due to my employment and am now staying in the trailer. Not sure how to fix this and or if I can still hook up the water. I’m scared to do anything because I dont want to make things worse. Thank u in advanced for your help.
If a valve is broken that is used to switch between drain fields, what is process of fixing it? What is cost to have it done?
Pleaseregisterto post and access all features of our very popular forum. It is free and quick. Over $68,000 in prizes has already been given out to active posters on our forum. Additional giveaways are planned. Detailed information about all U.S. cities, counties, and zip codes on our site:City-data.com.

All times are GMT -6.

How a Diverter Box Should Work

Tour of the Diverter Box, as well as Common Issues and Maintenance Geauga County, Ohio is the location. Tom Frank: I’d want to thank you for your time. This is an example of a septic system, complete with leach trenches and what is known as a diverter box. In the leech trenches, the area is separated into two halves. We have two halves of the house: an upper portion that is closest to the septic tank, and a lower half that is the furthest away. There are two boxes in this section. In this box is the diverter box, and this trench is the first trench on the upper side of the structure.

  • You would need to take it in order to switch a diverter box.
  • The explanation for this elbow is that we aren’t utilizing it; it has been turned off completely.
  • We’ll be focusing on the bottom side for the time being and resting the upper side.
  • Putting the elbow on there will cause issues up in the septic tank, which you do not want to happen.
  • The reason for this is because the water that comes out of the septic tank is still a little turbid as it leaves the tank.
  • By giving this one a year’s rest, we want to allow it to repair itself and let nature to take its course, allowing some of the stuff to drain away so that when the water is returned to it, the water can get back into the soil.
  • If you notice a damp patch forming on the side of the house that you are currently using, you may need to replace it before the end of the year.

The purpose of the year is to allow for a complete cycle of seasons.

TF: Solids account for around 25-30 percent of the total volume.

As a result, the entire volume.

When it begins to rise beyond the 30 percent threshold, it is sent via your water system to the secondary treatment facility for treatment.

Everyone wants to know when their tank is full; yet, you don’t want your tank to be full since, similar to an oil filter, once it is full, it is too late to do anything about it.

To get out of the pipe and into the real problem area, that bacterium will have to work hard at it.

Why are we interested about what occurs when the water seeps through the perforated pipe and into the stone?

TF: Alternatively, it will just overflow the box.

Matt:because It’s of the puncture in the pipe.

We want it to get out of those ditches and into the soil as much as possible.

We can’t cure everyone, either, at this point.

So that’s what we’re going to try and do: try and accomplish something.

However, we must first understand the system’s past.

It’s important to understand what we’re dealing with, and sometimes we’ll go so far as to have a soil scientist come out and look at the soils around the system to determine whether we can get the water into the soil and if it will take the water away, or if the soil is simply too bad to take the water away.

When the water table rises to the surface of the earth, it is around 6-8 inches above the ground’s surface from October through April.

As a result, there is a soil process. There are air spaces in the soil, and those air pockets will be brimming with water during the winter months. So you’ve got a wet sponge out here, and you’re attempting to put additional water into a wet sponge, but it’s not going to work.

Stuck diverter valve after the tank

This system has been in operation for 30 years, and there are two lines that collect the liquid effluent. In addition, one of them has a high level that may be accessed for examination. I’m not sure whether any solids have made their way out of the tank, but the most recent examination revealed that everything was in working order and that the sucm was about what I expected. This comes from the pumper, who I imagine is well-versed in the finer points of what is good and bad. It was suggested that I investigate just allowing the liquids to pass through the valve and let the field to absorb it, one line at a time.

  1. The place where I reside in Santa Cruz County, California, is quite particular about how things are done, and they demand plans and inspections on everyone.
  2. The valve is required by law, but I am unable to comment on its technical merits or advantages.
  3. There aren’t any trees to interfere with it, or at least I don’t think the oak trees can reach that far out.
  4. All I hope is that I don’t break it.
  5. The tech had a look at the design prints for the valve’s internals and externals.
  6. So, I’m going to give it a go and see how it turns out.
  7. For those who are interested, I will provide an update.

Distribution Valves « The Septic Store

Drainfields, textile filters, and sand filters are among the systems that employ Orenco ®Distributing Valve Assemblies to dose filtered effluent to multiple-zone pressure distribution systems. They are mechanically driven and use a combination of pressure and flow to successively divert the pump’s flow to numerous zones or cells, which is done automatically.

  • Distribution Valve Model GuidePDF
  • Technical Data SheetPDF
  • Product Data SheetPDF
  • Distribution Valve Model Guide PDF
  • Automatic and mechanical operation are offered
  • A variety of flow ranges are provided. Smaller horsepower pumps may be used on big drainfields and sand filters, which saves money. PVC fittings, unions, ball valves, and pipe in the Schedule 40 size range
  • Distribution valves made of ABS polymer and stainless steel
  • Units with 2-4 outlets and units with 5-6 outlets are both available. Inlet and exit sizes of 1-14 inch or 1-12 inch NPS (32 or 40 mm DN) are available. Maximum head pressures of 170 feet or 345 feet (52 meters or 105 meters) are offered. Enclosures that are custom-built are available.

Each Distributing Valve Assembly is custom-built to meet the precise requirements of a certain drainfield or drainage system. Call Orenco if you would like more information on obtaining a Distributing Valve Assembly for your project. Orenco Distributing Valve Assemblies can be housed in custom-built enclosures, which are available upon request.

septic emergency? help!

Hello everyone, I’m having a septic problem, and I’m expecting a large group of family members to arrive for the holidays. Please assist me! Septic tank and drain field are installed on our property. A few years ago, the prior owner had a whole second drain field with a diverter valve installed by a professional. I inquired as to why, and he responded that it allows one to rest. That looked unusual to me – why not just leave both lights on at the same time? We’ve been in the house for eight months.

  • I investigated.
  • As a result, he suggested I put something in there that would gobble it up, which may give me some time – or replace the fields (I ended up doing nothing and all has continued to work fine until now).
  • A copy of the actual septic work that was completed in 2008 was sent to me.
  • I got in touch with the contractor who had completed the new work.
  • He advised that it should be changed approximately every year.
  • So I walked outdoors with a long water main post/tool in hand, located the valve, and “swapped fields.” This occurred around 1.5 months ago.
  • As a result, I’ve done a lot of reading on septic systems, and I’ve heard that if a field is inundated, you’re screwed.

I looked at the invoices, and the previous owner had given this individual a substantial sum of money, and he has maintained his good reputation in the community.

A big downpour, for example, may cause some troubles in the basement, amongst other things.

Now, we’ve got a dilemma on our hands.

My wife did a ton of laundry today, and it just so happened that we and the kids all had showers/baths at the same time.

Even worse, I went to the bathroom on the first level.

We haven’t had much rain recently, and we haven’t gotten much rain in the previous several days.

As a result, it’s possible that the weather in Atlanta is holding moisture in the ground.

SOOOOO.

1.

The entire system has been hacked, and I require all new fields.

I’m OK – it’s simply a coincidence that we used so much water today that we flooded the system, and everything will be fine by the next day, I promise.

As a result, I should switch back. 4. The septic tank has reached capacity. Do you have any opinions on this? I’m well aware that there are several alternatives. But I’m running out of time and need to make a well-informed decision as soon as possible! Thanks!

septic system saga – please help!

Greetings, everyone! I’m having a septic problem, and I’m expecting a large number of family members for the holidays. Please assist me! Septic tank and drain field are installed on our property. An full second drain field with a diverter valve was added by the previous owner a few years ago, and it is still operational. In response to my question, he stated that it allows one to relax. After all, why not just leave both lights on at the same time? For the past eight months, we’ve been in the residence.

It was just a matter of time until I became concerned and called for help.

I dialed the phone number for my city and spoke with someone.

They brought back with them the original septic field and system architecture as well as their equipment.

“Dual systems” with diverter valves, according to him, were the greatest option and that everyone should consider installing one if they had the means to do so.

I’m working one drain field for a year, then another for a year, and so on and so forth.

Approximately 1.5 months have passed since this occurred.

As a result, I’ve done a lot of reading on septic systems, and I’ve heard that if a field is flooded, you’re screwed.

I looked at the records, and it appears that the previous owner spent a lot of money on this individual, who has maintained his good reputation in the community.

A severe downpour, for example, may cause some troubles in the basement, amongst other locations.

We have an issue right now, though.

As a result of my wife’s extensive washing today, we and the kids were able to have showers or bathes at the same time.

Adding to the misery, I went to use the restroom on the first level.

Our area hasn’t seen a lot of rain recently, and the previous few days have been particularly dry.

Because of this, it is possible that the weather in Atlanta is maintaining moisture in the soil.

SOOOOO.

There is a bug in the system and I need to add all fresh information.

I’m OK – it’s simply a coincidence that we used so much water today that we flooded the system, and everything will be fine by the next day.

Lastly, when I switched it 1.5 months ago, it went to an old field that had maybe been hacked and had not yet cleared itself of any corruption.

In such case, I should return to my previous position. It is necessary to pump out the septic tank. Do you have any opinions on this? I’m well aware that there are several options. My only problem is that I only have a limited amount of time and must make a decision as soon as possible! Thanks!

Leave a Comment

Your email address will not be published. Required fields are marked *